This patch adds support for the Favr-32 board made by EarthLCD.

This kit, which is also called ezLCD-101 when running with EarthLCD firmware, has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash, Ethernet, audio out, USB device, SD-card slot, USART and various other connectors for cennecting stuff to SPI, I2C, GPIO, etc.

Signed-off-by: Hans-Christian Egtvedt hans-christian.egtvedt@atmel.com --- The board will so far need to have a flash driver, since the CFI driver does not work for the time being. Håvard said he might look into it soon, and this board will be updated when the CFI driver can handle AT49BV6416 devices (and that family).

MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + board/earthlcd/favr-32-ezkit/Makefile | 42 +++++ board/earthlcd/favr-32-ezkit/config.mk | 4 + board/earthlcd/favr-32-ezkit/favr-32-ezkit.c | 96 +++++++++++ board/earthlcd/favr-32-ezkit/flash.c | 230 ++++++++++++++++++++++++++ board/earthlcd/favr-32-ezkit/u-boot.lds | 71 ++++++++ include/configs/favr-32-ezkit.h | 201 ++++++++++++++++++++++ 9 files changed, 652 insertions(+), 0 deletions(-) create mode 100644 board/earthlcd/favr-32-ezkit/Makefile create mode 100644 board/earthlcd/favr-32-ezkit/config.mk create mode 100644 board/earthlcd/favr-32-ezkit/favr-32-ezkit.c create mode 100644 board/earthlcd/favr-32-ezkit/flash.c create mode 100644 board/earthlcd/favr-32-ezkit/u-boot.lds create mode 100644 include/configs/favr-32-ezkit.h

diff --git a/MAINTAINERS b/MAINTAINERS index cbe5c47..0ff2add 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -709,6 +709,10 @@ Haavard Skinnemoen hskinnemoen@atmel.com ATSTK1006 AT32AP7000 ATNGW100 AT32AP7000

+Hans-Christian Egtvedt hans-christian.egtvedt@atmel.com + + FAVR-32-EZKIT AT32AP7000 + ######################################################################### # SuperH Systems: # # # diff --git a/MAKEALL b/MAKEALL index ee83cca..76dd334 100755 --- a/MAKEALL +++ b/MAKEALL @@ -714,6 +714,7 @@ LIST_avr32=" \ atstk1004 \ atstk1006 \ atngw100 \ + favr-32-ezkit \ "

######################################################################### diff --git a/Makefile b/Makefile index 3179c67..ebbf2bc 100644 --- a/Makefile +++ b/Makefile @@ -2911,6 +2911,9 @@ atstk1004_config : unconfig atstk1006_config : unconfig @$(MKCONFIG) $(@:_config=) avr32 at32ap atstk1000 atmel at32ap700x

+favr-32-ezkit_config : unconfig + @$(MKCONFIG) $(@:_config=) avr32 at32ap favr-32-ezkit earthlcd at32ap700x + #======================================================================== # SH3 (SuperH) #======================================================================== diff --git a/board/earthlcd/favr-32-ezkit/Makefile b/board/earthlcd/favr-32-ezkit/Makefile new file mode 100644 index 0000000..3e67a65 --- /dev/null +++ b/board/earthlcd/favr-32-ezkit/Makefile @@ -0,0 +1,42 @@ +# +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2008 Atmel Corporation +# +# See file CREDITS for list of people who contributed to this project. +# +# This program is free software; you can redistribute it and/or modify it under +# the terms of the GNU General Public License as published by the Free Software +# Foundation; either version 2 of the License, or (at your option) any later +# version. +# +# This program is distributed in the hope that it will be useful, but WITHOUT +# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS +# FOR A PARTICULAR PURPOSE. See the GNU General Public License for more +# details. +# +# You should have received a copy of the GNU General Public License along with +# this program; if not, write to the Free Software Foundation, Inc., 59 Temple +# Place, Suite 330, Boston, MA 02111-1307 USA + +include $(TOPDIR)/config.mk + +LIB := $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o flash.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/earthlcd/favr-32-ezkit/config.mk b/board/earthlcd/favr-32-ezkit/config.mk new file mode 100644 index 0000000..2337d62 --- /dev/null +++ b/board/earthlcd/favr-32-ezkit/config.mk @@ -0,0 +1,4 @@ +PLATFORM_RELFLAGS += -ffunction-sections -fdata-sections +PLATFORM_LDFLAGS += --gc-sections +TEXT_BASE = 0x00000000 +LDSCRIPT = $(obj)board/earthlcd/favr-32-ezkit/u-boot.lds diff --git a/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c b/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c new file mode 100644 index 0000000..22b6981 --- /dev/null +++ b/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c @@ -0,0 +1,96 @@ +/* + * Copyright (C) 2008 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 Temple + * Place, Suite 330, Boston, MA 02111-1307 USA + */ +#include <common.h> + +#include <asm/io.h> +#include <asm/sdram.h> +#include <asm/arch/clk.h> +#include <asm/arch/gpio.h> +#include <asm/arch/hmatrix.h> + +DECLARE_GLOBAL_DATA_PTR; + +static const struct sdram_config sdram_config = { + /* MT48LC4M32B2P-6 (16 MB) */ + .data_bits = SDRAM_DATA_32BIT, + .row_bits = 12, + .col_bits = 8, + .bank_bits = 2, + .cas = 3, + .twr = 2, + .trc = 7, + .trp = 2, + .trcd = 2, + .tras = 5, + .txsr = 5, + /* 15.6 us */ + .refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000, +}; + +int board_early_init_f(void) +{ + /* Enable SDRAM in the EBI mux */ + hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE)); + + gpio_enable_ebi(); + gpio_enable_usart3(); +#if defined(CONFIG_MACB) + gpio_enable_macb0(); +#endif +#if defined(CONFIG_MMC) + gpio_enable_mmci(); +#endif + + return 0; +} + +phys_size_t initdram(int board_type) +{ + unsigned long expected_size; + unsigned long actual_size; + void *sdram_base; + + sdram_base = map_physmem(EBI_SDRAM_BASE, EBI_SDRAM_SIZE, MAP_NOCACHE); + + expected_size = sdram_init(sdram_base, &sdram_config); + actual_size = get_ram_size(sdram_base, expected_size); + + unmap_physmem(sdram_base, EBI_SDRAM_SIZE); + + if (expected_size != actual_size) + printf("Warning: Only %u of %u MiB SDRAM is working\n", + actual_size >> 20, expected_size >> 20); + + return actual_size; +} + +void board_init_info(void) +{ + gd->bd->bi_phy_id[0] = 0x01; +} + +#if defined(CONFIG_MACB) && defined(CONFIG_CMD_NET) +extern int macb_eth_initialize(int id, void *regs, unsigned int phy_addr); + +int board_eth_init(bd_t *bi) +{ + return macb_eth_initialize(0, (void *)MACB0_BASE, bi->bi_phy_id[0]); +} +#endif diff --git a/board/earthlcd/favr-32-ezkit/flash.c b/board/earthlcd/favr-32-ezkit/flash.c new file mode 100644 index 0000000..49a715a --- /dev/null +++ b/board/earthlcd/favr-32-ezkit/flash.c @@ -0,0 +1,230 @@ +/* + * Copyright (C) 2008 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 Temple + * Place, Suite 330, Boston, MA 02111-1307 USA + */ +#include <common.h> + +#ifdef CONFIG_FAVR32_EZKIT_EXT_FLASH +#include <asm/cacheflush.h> +#include <asm/io.h> +#include <asm/sections.h> + +DECLARE_GLOBAL_DATA_PTR; + +flash_info_t flash_info[1]; + +static void flash_identify(uint16_t *flash, flash_info_t *info) +{ + unsigned long flags; + + flags = disable_interrupts(); + + dcache_flush_unlocked(); + + writew(0xaa, flash + 0x555); + writew(0x55, flash + 0xaaa); + writew(0x90, flash + 0x555); + info->flash_id = readl(flash); + writew(0xff, flash); + + readw(flash); + + if (flags) + enable_interrupts(); +} + +unsigned long flash_init(void) +{ + unsigned long addr; + unsigned int i; + + flash_info[0].size = CFG_FLASH_SIZE; + flash_info[0].sector_count = 135; + + flash_identify(uncached((void *)CFG_FLASH_BASE), &flash_info[0]); + + for (i = 0, addr = 0; i < 8; i++, addr += 0x2000) + flash_info[0].start[i] = addr; + for (; i < flash_info[0].sector_count; i++, addr += 0x10000) + flash_info[0].start[i] = addr; + + return CFG_FLASH_SIZE; +} + +void flash_print_info(flash_info_t *info) +{ + printf("Flash: Vendor ID: 0x%02x, Product ID: 0x%02x\n", + info->flash_id >> 16, info->flash_id & 0xffff); + printf("Size: %ld MB in %d sectors\n", + info->size >> 10, info->sector_count); +} + +int flash_erase(flash_info_t *info, int s_first, int s_last) +{ + unsigned long flags; + unsigned long start_time; + uint16_t *fb, *sb; + unsigned int i; + int ret; + uint16_t status; + + if ((s_first < 0) || (s_first > s_last) + || (s_last >= info->sector_count)) { + puts("Error: first and/or last sector out of range\n"); + return ERR_INVAL; + } + + for (i = s_first; i < s_last; i++) + if (info->protect[i]) { + printf("Error: sector %d is protected\n", i); + return ERR_PROTECTED; + } + + fb = (uint16_t *)uncached(info->start[0]); + + dcache_flush_unlocked(); + + for (i = s_first; (i <= s_last) && !ctrlc(); i++) { + printf("Erasing sector %3d...", i); + + sb = (uint16_t *)uncached(info->start[i]); + + flags = disable_interrupts(); + + start_time = get_timer(0); + + /* Unlock sector */ + writew(0xaa, fb + 0x555); + writew(0x70, sb); + + /* Erase sector */ + writew(0xaa, fb + 0x555); + writew(0x55, fb + 0xaaa); + writew(0x80, fb + 0x555); + writew(0xaa, fb + 0x555); + writew(0x55, fb + 0xaaa); + writew(0x30, sb); + + /* Wait for completion */ + ret = ERR_OK; + do { + /* TODO: Timeout */ + status = readw(sb); + } while ((status != 0xffff) && !(status & 0x28)); + + writew(0xf0, fb); + + /* + * Make sure the command actually makes it to the bus + * before we re-enable interrupts. + */ + readw(fb); + + if (flags) + enable_interrupts(); + + if (status != 0xffff) { + printf("Flash erase error at address 0x%p: 0x%02x\n", + sb, status); + ret = ERR_PROG_ERROR; + break; + } + } + + if (ctrlc()) + printf("User interrupt!\n"); + + return ERR_OK; +} + +int write_buff(flash_info_t *info, uchar *src, + ulong addr, ulong count) +{ + unsigned long flags; + uint16_t *base, *p, *s, *end; + uint16_t word, status, status1; + int ret = ERR_OK; + + if (addr < info->start[0] + || (addr + count) > (info->start[0] + info->size) + || (addr + count) < addr) { + puts("Error: invalid address range\n"); + return ERR_INVAL; + } + + if (addr & 1 || count & 1 || (unsigned int)src & 1) { + puts("Error: misaligned source, destination or count\n"); + return ERR_ALIGN; + } + + base = (uint16_t *)uncached(info->start[0]); + end = (uint16_t *)uncached(addr + count); + + flags = disable_interrupts(); + + dcache_flush_unlocked(); + sync_write_buffer(); + + for (p = (uint16_t *)uncached(addr), s = (uint16_t *)src; + p < end && !ctrlc(); p++, s++) { + word = *s; + + writew(0xaa, base + 0x555); + writew(0x55, base + 0xaaa); + writew(0xa0, base + 0x555); + writew(word, p); + + sync_write_buffer(); + + /* Wait for completion */ + status1 = readw(p); + do { + /* TODO: Timeout */ + status = status1; + status1 = readw(p); + } while (((status ^ status1) & 0x40) /* toggled */ + && !(status1 & 0x28)); /* error bits */ + + /* + * We'll need to check once again for toggle bit + * because the toggle bit may stop toggling as I/O5 + * changes to "1" (ref at49bv642.pdf p9) + */ + status1 = readw(p); + status = readw(p); + if ((status ^ status1) & 0x40) { + printf("Flash write error at address 0x%p: " + "0x%02x != 0x%02x\n", + p, status,word); + ret = ERR_PROG_ERROR; + writew(0xf0, base); + readw(base); + break; + } + + writew(0xf0, base); + readw(base); + } + + if (flags) + enable_interrupts(); + + return ret; +} + +#endif /* CONFIG_FAVR32_EZKIT_EXT_FLASH */ diff --git a/board/earthlcd/favr-32-ezkit/u-boot.lds b/board/earthlcd/favr-32-ezkit/u-boot.lds new file mode 100644 index 0000000..ad056b3 --- /dev/null +++ b/board/earthlcd/favr-32-ezkit/u-boot.lds @@ -0,0 +1,71 @@ +/* -*- Fundamental -*- + * + * Copyright (C) 2008 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 Temple + * Place, Suite 330, Boston, MA 02111-1307 USA + */ +OUTPUT_FORMAT("elf32-avr32", "elf32-avr32", "elf32-avr32") +OUTPUT_ARCH(avr32) +ENTRY(_start) + +SECTIONS +{ + . = 0; + _text = .; + .text : { + *(.exception.text) + *(.text) + *(.text.*) + } + _etext = .; + + .rodata : { + *(.rodata) + *(.rodata.*) + } + + . = ALIGN(8); + _data = .; + .data : { + *(.data) + *(.data.*) + } + + . = ALIGN(4); + __u_boot_cmd_start = .; + .u_boot_cmd : { + KEEP(*(.u_boot_cmd)) + } + __u_boot_cmd_end = .; + + . = ALIGN(4); + _got = .; + .got : { + *(.got) + } + _egot = .; + + . = ALIGN(8); + _edata = .; + + .bss (NOLOAD) : { + *(.bss) + *(.bss.*) + } + . = ALIGN(8); + _end = .; +} diff --git a/include/configs/favr-32-ezkit.h b/include/configs/favr-32-ezkit.h new file mode 100644 index 0000000..6f77c25 --- /dev/null +++ b/include/configs/favr-32-ezkit.h @@ -0,0 +1,201 @@ +/* + * Copyright (C) 2008 Atmel Corporation + * + * Configuration settings for the Favr-32 EarthLCD LCD kit. + * + * See file CREDITS for list of people who contributed to this project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., 59 Temple + * Place, Suite 330, Boston, MA 02111-1307 USA + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/memory-map.h> + +#define CONFIG_AVR32 1 +#define CONFIG_AT32AP 1 +#define CONFIG_AT32AP7000 1 +#define CONFIG_FAVR32_EZKIT 1 + +#define CONFIG_FAVR32_EZKIT_EXT_FLASH 1 + +/* + * Timer clock frequency. We're using the CPU-internal COUNT register + * for this, so this is equivalent to the CPU core clock frequency + */ +#define CFG_HZ 1000 + +/* + * Set up the PLL to run at 140 MHz, the CPU to run at the PLL + * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the + * PLL frequency. + * (CFG_OSC0_HZ * CFG_PLL0_MUL) / CFG_PLL0_DIV = PLL MHz + */ +#define CONFIG_PLL 1 +#define CFG_POWER_MANAGER 1 +#define CFG_OSC0_HZ 20000000 +#define CFG_PLL0_DIV 1 +#define CFG_PLL0_MUL 7 +#define CFG_PLL0_SUPPRESS_CYCLES 16 +/* + * Set the CPU running at: + * PLL / (2^CFG_CLKDIV_CPU) = CPU MHz + */ +#define CFG_CLKDIV_CPU 0 +/* + * Set the HSB running at: + * PLL / (2^CFG_CLKDIV_HSB) = HSB MHz + */ +#define CFG_CLKDIV_HSB 1 +/* + * Set the PBA running at: + * PLL / (2^CFG_CLKDIV_PBA) = PBA MHz + */ +#define CFG_CLKDIV_PBA 2 +/* + * Set the PBB running at: + * PLL / (2^CFG_CLKDIV_PBB) = PBB MHz + */ +#define CFG_CLKDIV_PBB 1 + +/* + * The PLLOPT register controls the PLL like this: + * icp = PLLOPT<2> + * ivco = PLLOPT<1:0> + * + * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). + */ +#define CFG_PLL0_OPT 0x04 + +#undef CONFIG_USART0 +#undef CONFIG_USART1 +#undef CONFIG_USART2 +#define CONFIG_USART3 1 + +/* User serviceable stuff */ +#define CONFIG_DOS_PARTITION 1 + +#define CONFIG_CMDLINE_TAG 1 +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_STACKSIZE (2048) + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTARGS \ + "root=/dev/mtdblock1 rootfstype=jffs fbmem=1800k" + +#define CONFIG_BOOTCOMMAND \ + "fsload; bootm $(fileaddr)" + +/* + * Only interrupt autoboot if <space> is pressed. Otherwise, garbage + * data on the serial line may interrupt the boot sequence. + */ +#define CONFIG_BOOTDELAY 1 +#define CONFIG_AUTOBOOT 1 +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n" +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * After booting the board for the first time, new ethernet addresses + * should be generated and assigned to the environment variables + * "ethaddr" and "eth1addr". This is normally done during production. + */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 +#define CONFIG_NET_MULTI 1 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MMC + +#undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_XIMG + +#define CONFIG_ATMEL_USART 1 +#define CONFIG_MACB 1 +#define CONFIG_PIO2 1 +#define CFG_NR_PIOS 5 +#define CFG_HSDRAMC 1 +#define CONFIG_MMC 1 +#define CONFIG_ATMEL_MCI 1 + +#define CFG_DCACHE_LINESZ 32 +#define CFG_ICACHE_LINESZ 32 + +#define CONFIG_NR_DRAM_BANKS 1 + +/* External flash on Favr-32 */ +#if 0 +#define CFG_FLASH_CFI 1 +#define CFG_FLASH_CFI_DRIVER 1 +#endif + +#define CFG_FLASH_BASE 0x00000000 +#define CFG_FLASH_SIZE 0x800000 +#define CFG_MAX_FLASH_BANKS 1 +#define CFG_MAX_FLASH_SECT 135 + +#define CFG_MONITOR_BASE CFG_FLASH_BASE + +#define CFG_INTRAM_BASE INTERNAL_SRAM_BASE +#define CFG_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CFG_SDRAM_BASE EBI_SDRAM_BASE + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 65536 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_FLASH_SIZE - CFG_ENV_SIZE) + +#define CFG_INIT_SP_ADDR (CFG_INTRAM_BASE + CFG_INTRAM_SIZE) + +#define CFG_MALLOC_LEN (256*1024) +#define CFG_DMA_ALLOC_LEN (16384) + +/* Allow 4MB for the kernel run-time image */ +#define CFG_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) +#define CFG_BOOTPARAMS_LEN (16 * 1024) + +/* Other configuration settings that shouldn't have to change all that often */ +#define CFG_PROMPT "U-Boot> " +#define CFG_CBSIZE 256 +#define CFG_MAXARGS 16 +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_LONGHELP 1 + +#define CFG_MEMTEST_START EBI_SDRAM_BASE +#define CFG_MEMTEST_END (CFG_MEMTEST_START + 0x700000) +#define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } + +#endif /* __CONFIG_H */