Signed-off-by: Lubomir Popov lpopov@mm-sol.com

---

The som5_evb is an evaluation board for the APM-5 - a OMAP5430-based SOM (system On a Module) designed by MMS and manufactured under license by Jorjin Technologies.

arch/arm/include/asm/mach-types.h | 13 ++ board/mms/som5_evb/Makefile | 49 +++++ board/mms/som5_evb/s5evb_mux_data.h | 376 +++++++++++++++++++++++++++++++++++ board/mms/som5_evb/som5_evb.c | 200 +++++++++++++++++++ boards.cfg | 1 + include/configs/omap5_som5_evb.h | 336 +++++++++++++++++++++++++++++++ 6 files changed, 975 insertions(+) create mode 100644 board/mms/som5_evb/Makefile create mode 100644 board/mms/som5_evb/s5evb_mux_data.h create mode 100644 board/mms/som5_evb/som5_evb.c create mode 100644 include/configs/omap5_som5_evb.h

diff --git a/arch/arm/include/asm/mach-types.h b/arch/arm/include/asm/mach-types.h index a676b6d..236fa17 100644 --- a/arch/arm/include/asm/mach-types.h +++ b/arch/arm/include/asm/mach-types.h @@ -1107,6 +1107,7 @@ extern unsigned int __machine_arch_type; #define MACH_TYPE_OMAP5_SEVM 3777 #define MACH_TYPE_ARMADILLO_800EVA 3863 #define MACH_TYPE_KZM9G 4140 +#define MACH_TYPE_SOM5_EVB 4545

#ifdef CONFIG_ARCH_EBSA110 # ifdef machine_arch_type @@ -14248,6 +14249,18 @@ extern unsigned int __machine_arch_type; # define machine_is_kzm9g() (0) #endif

+#ifdef CONFIG_MACH_SOM5_EVB +# ifdef machine_arch_type +# undef machine_arch_type +# define machine_arch_type __machine_arch_type +# else +# define machine_arch_type MACH_TYPE_SOM5_EVB +# endif +# define machine_is_som5_evb() (machine_arch_type == MACH_TYPE_SOM5_EVB) +#else +# define machine_is_som5_evb() (0) +#endif + /* * These have not yet been registered */ diff --git a/board/mms/som5_evb/Makefile b/board/mms/som5_evb/Makefile new file mode 100644 index 0000000..248e5cc --- /dev/null +++ b/board/mms/som5_evb/Makefile @@ -0,0 +1,49 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := som5_evb.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/mms/som5_evb/s5evb_mux_data.h b/board/mms/som5_evb/s5evb_mux_data.h new file mode 100644 index 0000000..791a4ad --- /dev/null +++ b/board/mms/som5_evb/s5evb_mux_data.h @@ -0,0 +1,376 @@ +/* + * Copyright (C) 2013 MM Solutions AD, <www.mm-sol.com> + * + * Lubomir Popov lpopov@mm-sol.com l-popov@ti.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _SOM5_EVB_MUX_DATA_H +#define _SOM5_EVB_MUX_DATA_H + +#include <asm/arch/mux_omap5.h> + +const struct pad_conf_entry core_padconf_array_essential[] = { + + {EMMC_CLK, (PTU | IEN | M0)}, /* EMMC_CLK */ + {EMMC_CMD, (PTU | IEN | M0)}, /* EMMC_CMD */ + {EMMC_DATA0, (PTU | IEN | M0)}, /* EMMC_DATA0 */ + {EMMC_DATA1, (PTU | IEN | M0)}, /* EMMC_DATA1 */ + {EMMC_DATA2, (PTU | IEN | M0)}, /* EMMC_DATA2 */ + {EMMC_DATA3, (PTU | IEN | M0)}, /* EMMC_DATA3 */ + {EMMC_DATA4, (PTU | IEN | M0)}, /* EMMC_DATA4 */ + {EMMC_DATA5, (PTU | IEN | M0)}, /* EMMC_DATA5 */ + {EMMC_DATA6, (PTU | IEN | M0)}, /* EMMC_DATA6 */ + {EMMC_DATA7, (PTU | IEN | M0)}, /* EMMC_DATA7 */ + + {SDCARD_CLK, (PTU | IEN | M0)}, /* SDCARD_CLK */ + {SDCARD_CMD, (PTU | IEN | M0)}, /* SDCARD_CMD */ + {SDCARD_DATA0, (PTU | IEN | M0)}, /* SDCARD_DATA0 */ + {SDCARD_DATA1, (PTU | IEN | M0)}, /* SDCARD_DATA1 */ + {SDCARD_DATA2, (PTU | IEN | M0)}, /* SDCARD_DATA2 */ + {SDCARD_DATA3, (PTU | IEN | M0)}, /* SDCARD_DATA3 */ + + {UART3_RX_IRRX, (PTU | IEN | M0)},/* UART3_RX_IRRX */ + {UART3_TX_IRTX, (M0)}, /* UART3_TX_IRTX */ + + {HSI2_CAREADY, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_CLK */ + {HSI2_ACREADY, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_NXT */ + {HSI2_CAWAKE, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DIR */ + {HSI2_ACWAKE, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_STP */ + {HSI2_CAFLAG, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA0 */ + {HSI2_CADATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA1 */ + {HSI2_ACFLAG, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA2 */ + {HSI2_ACDATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA3 */ + {UART2_RTS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA4 */ + {UART2_CTS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA5 */ + {UART2_RX, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA6 */ + {UART2_TX, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* USBB1_ULPIPHY_DATA7 */ + + {USBB2_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB2_HSIC_STROBE */ + {USBB2_HSIC_DATA, (PTU | IEN | M0)}, /* USBB2_HSIC_DATA */ + + {USBB3_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB3_HSIC_STROBE */ + {USBB3_HSIC_DATA, (PTU | IEN | M0)}, /* USBB3_HSIC_DATA */ + + {USBD0_HS_DP, (IEN | M0)}, /* USBD0_HS_DP */ + {USBD0_HS_DM, (IEN | M0)}, /* USBD0_HS_DM */ + {USBD0_SS_RX, (IEN | M0)}, /* USBD0_SS_RX (LP: WTF is this for?) */ + +}; + +const struct pad_conf_entry wkup_padconf_array_essential[] = { + + {SR_PMIC_SCL, (PTU | IEN | M0)}, /* SR_PMIC_SCL */ + {SR_PMIC_SDA, (PTU | IEN | M0)}, /* SR_PMIC_SDA */ + + {SYS_32K, (IEN | M0)}, /* SYS_32K */ + +}; + +const struct pad_conf_entry core_padconf_array_non_essential[] = { +#if 0 +/* GPMC is actually not useable directly as we don't have + the GPMC_NOE_NRE signal available, and some external logic + shall be needed. Anyway, M4 is the reset default. +*/ + {C2C_DATAIN0, (IEN | M4)}, /* GPMC_AD0 */ + {C2C_DATAIN1, (IEN | M4)}, /* GPMC_AD1 */ + {C2C_DATAIN2, (IEN | M4)}, /* GPMC_AD2 */ + {C2C_DATAIN3, (IEN | M4)}, /* GPMC_AD3 */ + {C2C_DATAIN4, (IEN | M4)}, /* GPMC_AD4 */ + {C2C_DATAIN5, (IEN | M4)}, /* GPMC_AD5 */ + {C2C_DATAIN6, (IEN | M4)}, /* GPMC_AD6 */ + {C2C_DATAIN7, (IEN | M4)}, /* GPMC_AD7 */ + {C2C_CLKIN1, (IEN | M4)}, /* GPMC_CLK */ + {C2C_CLKIN0, (M5)}, /* GPMC_NBE1 */ + {C2C_CLKOUT0, (M4)}, /* GPMC_NADV_ALE */ + {C2C_CLKOUT1, (M4)}, /* GPMC_NBE0_CLE */ + {C2C_DATAOUT0, (IEN | M4)}, /* GPMC_AD8 */ + {C2C_DATAOUT1, (IEN | M4)}, /* GPMC_AD9 */ + {C2C_DATAOUT2, (IEN | M4)}, /* GPMC_AD10 */ + {C2C_DATAOUT3, (IEN | M4)}, /* GPMC_AD11 */ + {C2C_DATAOUT4, (IEN | M4)}, /* GPMC_AD12 */ + {C2C_DATAOUT5, (IEN | M4)}, /* GPMC_AD13 */ + {C2C_DATAOUT6, (IEN | M4)}, /* GPMC_AD14 */ + {C2C_DATAOUT7, (IEN | M4)}, /* GPMC_AD15 */ + {C2C_DATA8, (M4)}, /* GPMC_A16 */ + {C2C_DATA9, (M4)}, /* GPMC_A17 */ + {C2C_DATA10, (M4)}, /* GPMC_A18 */ + {C2C_DATA11, (M4)}, /* GPMC_A19 */ + {C2C_DATA12, (M4)}, /* GPMC_A20 */ + {C2C_DATA13, (M4)}, /* GPMC_A21 */ + {C2C_DATA14, (M4)}, /* GPMC_A22 */ + {C2C_DATA15, (M4)}, /* GPMC_A23 */ + {LLIA_WAKEREQOUT, (PTU | IEN | M4)}, /* GPMC_WAIT0 */ + {UART1_RTS, (M4)}, /* GPMC_NCS7 */ +#else +/* Test in GPIO mode. Convention: left (odd) pins on connector are + outputs (initialized to PD), right (even) pins are inputs with PU. +*/ + {C2C_DATAIN0, (IEN | PTU | M6)}, /* GPIO2_37 In J201:06 */ + {C2C_DATAIN1, (IEN | PTU | M6)}, /* GPIO2_38 In J201:04 */ + {C2C_DATAIN2, (IEN | PTU | M6)}, /* GPIO2_39 In J201:10 */ + {C2C_DATAIN3, (IEN | PTU | M6)}, /* GPIO2_40 In J201:08 */ + {C2C_DATAIN4, (IEN | PTU | M6)}, /* GPIO2_41 In J201:16 */ + {C2C_DATAIN5, (IEN | PTU | M6)}, /* GPIO2_42 In J201:12 */ + {C2C_DATAIN6, (IEN | PTU | M6)}, /* GPIO2_43 In J201:20 */ + {C2C_DATAIN7, (IEN | PTU | M6)}, /* GPIO2_44 In J201:18 */ + {C2C_CLKIN1, (PTD | M6)}, /* GPIO2_36 Out J201:03 */ + {C2C_CLKIN0, (PTD | M6)}, /* GPIO2_35 Out J201:11 */ + {C2C_CLKOUT0, (PTD | M6)}, /* GPIO2_33 Out J201:17 */ + {C2C_CLKOUT1, (PTD | M6)}, /* GPIO2_34 Out J201:09 */ + {C2C_DATAOUT0, (PTD | M6)}, /* GPIO2_56 Out J201:31 */ + {C2C_DATAOUT1, (PTD | M6)}, /* GPIO2_57 Out J201:23 */ + {C2C_DATAOUT2, (PTD | M6)}, /* GPIO2_58 Out J201:25 */ + {C2C_DATAOUT3, (PTD | M6)}, /* GPIO2_59 Out J201:15 */ + {C2C_DATAOUT4, (PTD | M6)}, /* GPIO2_60 Out J201:29 */ + {C2C_DATAOUT5, (PTD | M6)}, /* GPIO2_61 Out J201:21 */ + {C2C_DATAOUT6, (IEN | PTU | M6)}, /* GPIO2_62 In J201:22 */ + {C2C_DATAOUT7, (IEN | PTU | M6)}, /* GPIO2_63 In J201:24 */ + {C2C_DATA8, (IEN | PTU | M6)}, /* GPIO4_113 In J201:32 */ + {C2C_DATA9, (IEN | PTU | M6)}, /* GPIO4_114 In J201:30 */ + {C2C_DATA10, (IEN | PTU | M6)}, /* GPIO4_115 In J201:36 */ + {C2C_DATA11, (IEN | PTU | M6)}, /* GPIO4_116 In J201:26 */ + {C2C_DATA12, (PTD | M6)}, /* GPIO4_117 Out J201:35 */ + {C2C_DATA13, (PTD | M6)}, /* GPIO4_118 Out J201:33 */ + {C2C_DATA14, (IEN | PTU | M6)}, /* GPIO4_119 In J201:38 */ + {C2C_DATA15, (IEN | PTU | M6)}, /* GPIO4_120 In J201:34 */ + {LLIA_WAKEREQOUT, (PTD | M6)}, /* GPIO2_45 Out J201:07 */ + {UART1_RTS, (PTD | M6)}, /* GPIO3_75 Out J201:37 */ +#endif + {LLIB_WAKEREQOUT, (PTU | IEN | M6)}, /* GPIO2_32 In I/O Exp Int */ + + {HSI1_ACREADY, (PTD | M6)}, /* GPIO3_64 Out J701:28 */ + {HSI1_CAREADY, (PTD | M6)}, /* GPIO3_65 Out J701:26 */ + {HSI1_ACWAKE, (PTD | M6)}, /* GPIO3_66 Out J801:25 */ + {HSI1_CAWAKE, (PTU | IEN | M6)}, /* GPIO3_67 In SDcard:CD */ + {HSI1_ACFLAG, (PTU | IEN | M6)}, /* GPIO3_68 In J801:22 */ + {HSI1_ACDATA, (PTD | M6)}, /* GPIO3_69 Out J801:21 */ + {HSI1_CAFLAG, (PTU | IEN | M6)}, /* GPIO3_70 In J801:32 */ + {HSI1_CADATA, (PTD | M6)}, /* GPIO3_71 Out J801:29 */ + {UART1_TX, (PTU | IEN | M6)}, /* GPIO3_72 In J801:26 */ + {UART1_CTS, (PTD | M6)}, /* GPIO3_73 Out J801:31 */ + {UART1_RX, (PTU | IEN | M6)}, /* GPIO3_74 In J801:30 */ + + {USBB1_HSIC_STROBE, (PTU | IEN | M6)}, /* GPIO3_92 In NU */ + {USBB1_HSIC_DATA, (PTU | IEN | M6)}, /* GPIO3_93 In NU */ + + {TIMER10_PWM_EVT, (PTD | M6)}, /* GPIO6_188 Out J802:11 */ + {DSIPORTA_TE0, (PTU | IEN | M6)}, /* GPIO6_189 In J802:26 */ + {DSIPORTA_LANE0X, (IEN | M0)}, /* DSIPORTA_LANE0X J704 */ + {DSIPORTA_LANE0Y, (IEN | M0)}, /* DSIPORTA_LANE0Y J704 */ + {DSIPORTA_LANE1X, (IEN | M0)}, /* DSIPORTA_LANE1X J704 */ + {DSIPORTA_LANE1Y, (IEN | M0)}, /* DSIPORTA_LANE1Y J704 */ + {DSIPORTA_LANE2X, (IEN | M0)}, /* DSIPORTA_LANE2X J704 */ + {DSIPORTA_LANE2Y, (IEN | M0)}, /* DSIPORTA_LANE2Y J704 */ + {DSIPORTA_LANE3X, (IEN | M0)}, /* DSIPORTA_LANE3X J704 */ + {DSIPORTA_LANE3Y, (IEN | M0)}, /* DSIPORTA_LANE3Y J704 */ + {DSIPORTA_LANE4X, (IEN | M0)}, /* DSIPORTA_LANE4X J704 */ + {DSIPORTA_LANE4Y, (IEN | M0)}, /* DSIPORTA_LANE4Y J704 */ + + {TIMER9_PWM_EVT, (PTU | IEN | M6)}, /* GPIO6_190 In J802:12 */ + {DSIPORTC_TE0, (PTD | M6)}, /* GPIO6_191 Out J802:15 */ + {DSIPORTC_LANE0X, (IEN | M0)}, /* DSIPORTC_LANE0X J702 */ + {DSIPORTC_LANE0Y, (IEN | M0)}, /* DSIPORTC_LANE0Y J702 */ + {DSIPORTC_LANE1X, (IEN | M0)}, /* DSIPORTC_LANE1X J702 */ + {DSIPORTC_LANE1Y, (IEN | M0)}, /* DSIPORTC_LANE1Y J702 */ + {DSIPORTC_LANE2X, (IEN | M0)}, /* DSIPORTC_LANE2X J702 */ + {DSIPORTC_LANE2Y, (IEN | M0)}, /* DSIPORTC_LANE2Y J702 */ + {DSIPORTC_LANE3X, (IEN | M0)}, /* DSIPORTC_LANE3X J702 */ + {DSIPORTC_LANE3Y, (IEN | M0)}, /* DSIPORTC_LANE3Y J702 */ + {DSIPORTC_LANE4X, (IEN | M0)}, /* DSIPORTC_LANE4X J702 */ + {DSIPORTC_LANE4Y, (IEN | M0)}, /* DSIPORTC_LANE4Y J702 */ + + {RFBI_HSYNC0, (M4)}, /* KBD_COL5 (Out) HOME */ + {RFBI_TE_VSYNC0, (PTD | M6)}, /* GPIO6_161 Out J704:24 3D_MODE_EN */ + {RFBI_WE, (PTD | M5)}, /* DRM_EMU2 (Out) */ + {RFBI_CS0, (PTD | M5)}, /* DRM_EMU3 (Out) */ + {RFBI_RE, (M4)}, /* KBD_COL4 (Out) SEND */ + {RFBI_A0, (PTU | IEN | M6)}, /* GPIO6_165 In SH2_SENS_INT */ + {RFBI_DATA0, (PTD | M5)}, /* DRM_EMU4 (Out) */ + {RFBI_DATA1, (PTD | M5)}, /* DRM_EMU5 (Out) */ + {RFBI_DATA2, (PTD | M5)}, /* DRM_EMU6 (Out) */ + {RFBI_DATA3, (PTD | M6)}, /* GPIO6_169 Out J704:22 3D_LCD_BANK_SEL */ + {RFBI_DATA4, (PTU | IEN | M6)}, /* GPIO6_170 In TEMP_ALERT on SOM (OD) */ + {RFBI_DATA5, (PTU | IEN | M6)}, /* GPIO6_171 In J802:30 */ + {RFBI_DATA6, (PTD | M6)}, /* GPIO6_172 Out LAN9730 nRESET */ + {RFBI_DATA7, (PTD | M6)}, /* GPIO6_173 Out USB4640 nRESET */ + {RFBI_DATA8, (M4)}, /* KBD_COL3 (Out) VOL- */ + {RFBI_DATA9, (PTD | M6)}, /* GPIO6_175 Out MCLK_1E */ + {RFBI_DATA10, (PTD | M6)}, /* GPIO6_176 Out MCLK_2E */ + {RFBI_DATA11, (PTD | M6)}, /* GPIO6_177 Out MCLK_3E */ + {RFBI_DATA12, (PTD | M6)}, /* GPIO6_178 Out J703:25 CAM_SUBPM_EN */ + {RFBI_DATA13, (PTU | IEN | M6)}, /* GPIO6_179 In J704:27 TSCR_INT (OD) */ + {RFBI_DATA14, (M4)}, /* KBD_COL7 (Out) SEARCH */ + {RFBI_DATA15, (M4)}, /* KBD_COL6 (Out) END */ + + {GPIO6_182, (PTU | IEN | M6)}, /* GPIO6_182 In J802:28 */ + {GPIO6_183, (PTD | M6)}, /* GPIO6_183 Out J704:25 nLCD_RESET */ + {GPIO6_184, (M4)}, /* KBD_COL2 (Out) VOL+ */ + {GPIO6_185, (PTU | IEN | M6)}, /* GPIO6_185 In J802:32 */ + {GPIO6_186, (PTD | M6)}, /* GPIO6_186 Out J802:25 */ + {GPIO6_187, (PTU | IEN | M4)}, /* KBD_ROW2 (In) All btns*/ +#if 0 + {MCSPI2_CS0, (M0)}, /* MCSPI2_CS0 J802:31 */ + {MCSPI2_CLK, (IEN | M0)}, /* MCSPI2_CLK J802:23 */ + {MCSPI2_SIMO, (IEN | M0)}, /* MCSPI2_SIMO J802:29 */ + {MCSPI2_SOMI, (PTU | IEN | M0)}, /* MCSPI2_SOMI J802:18 */ +#else + {MCSPI2_CS0, (PTD | M6)}, /* GPIO7_196 Out J802:31 */ + {MCSPI2_CLK, (PTD | M6)}, /* GPIO7_197 Out J802:23 */ + {MCSPI2_SIMO, (PTD | M6)}, /* GPIO7_198 Out J802:29 */ + {MCSPI2_SOMI, (PTU | IEN | M6)}, /* GPIO7_199 In J802:18 */ +#endif + {I2C4_SCL, (IEN | PTU | M0)}, /* I2C4_SCL */ + {I2C4_SDA, (IEN | PTU | M0)}, /* I2C4_SDA */ + + {HDMI_CEC, (IEN | M0)}, /* HDMI_CEC */ + {HDMI_HPD, (PTD | IEN | M0)}, /* HDMI_HPD */ + {HDMI_DDC_SCL, (IEN | M0)}, /* HDMI_DDC_SCL */ + {HDMI_DDC_SDA, (IEN | M0)}, /* HDMI_DDC_SDA */ + + {CSIPORTA_LANE0X, (IEN | M0)}, /* CSIPORTA_LANE0X */ + {CSIPORTA_LANE0Y, (IEN | M0)}, /* CSIPORTA_LANE0Y */ + {CSIPORTA_LANE1Y, (IEN | M0)}, /* CSIPORTA_LANE1Y */ + {CSIPORTA_LANE1X, (IEN | M0)}, /* CSIPORTA_LANE1X */ + {CSIPORTA_LANE2Y, (IEN | M0)}, /* CSIPORTA_LANE2Y */ + {CSIPORTA_LANE2X, (IEN | M0)}, /* CSIPORTA_LANE2X */ + {CSIPORTA_LANE3X, (IEN | M0)}, /* CSIPORTA_LANE3X */ + {CSIPORTA_LANE3Y, (IEN | M0)}, /* CSIPORTA_LANE3Y */ + {CSIPORTA_LANE4X, (IEN | M0)}, /* CSIPORTA_LANE4X */ + {CSIPORTA_LANE4Y, (IEN | M0)}, /* CSIPORTA_LANE4Y */ + + {CSIPORTB_LANE0X, (IEN | M0)}, /* CSIPORTB_LANE0X */ + {CSIPORTB_LANE0Y, (IEN | M0)}, /* CSIPORTB_LANE0Y */ + {CSIPORTB_LANE1Y, (IEN | M0)}, /* CSIPORTB_LANE1Y */ + {CSIPORTB_LANE1X, (IEN | M0)}, /* CSIPORTB_LANE1X */ + {CSIPORTB_LANE2Y, (IEN | M0)}, /* CSIPORTB_LANE2Y */ + {CSIPORTB_LANE2X, (IEN | M0)}, /* CSIPORTB_LANE2X */ + + {CSIPORTC_LANE0Y, (IEN | M0)}, /* CSIPORTC_LANE0Y */ + {CSIPORTC_LANE0X, (IEN | M0)}, /* CSIPORTC_LANE0X */ + {CSIPORTC_LANE1Y, (IEN | M0)}, /* CSIPORTC_LANE1Y */ + {CSIPORTC_LANE1X, (IEN | M0)}, /* CSIPORTC_LANE1X */ + + {CAM_SHUTTER, (M0)}, /* CAM_SHUTTER/224 J701:22 */ + {CAM_STROBE, (M0)}, /* CAM_STROBE/225 J701:24 */ + {CAM_GLOBALRESET, (IEN | M0)}, /* CAM_GLOBALRESET/226 J701:20 */ + {TIMER11_PWM_EVT, (PTD | M6)}, /* GPIO8_227 Out J703:26 PRIMARY_5M_RESET_N */ + {TIMER5_PWM_EVT, (PTD | M6)}, /* GPIO8_228 Out J703:28 SECONDARY_5M_RESET_N */ + {TIMER6_PWM_EVT, (PTD | M6)}, /* GPIO8_229 Out J701:18 */ + {TIMER8_PWM_EVT, (PTD | M6)}, /* GPIO8_230 Out J701:16 */ + + {I2C3_SCL, (IEN | PTU | M0)}, /* I2C3_SCL */ + {I2C3_SDA, (IEN | PTU | M0)}, /* I2C3_SDA */ + + {GPIO8_233, (PTD | M6)}, /* GPIO8_233 Out J701:25 */ + + {ABE_CLKS, (IEN | M0)}, /* ABE_CLKS */ + {ABEDMIC_DIN1, (PTD | M6)}, /* GPIO4_97 Out J801:13 */ + {ABEDMIC_DIN2, (PTU | IEN | M6)}, /* GPIO4_98 In J801:12 */ + {ABEDMIC_DIN3, (PTD | M6)}, /* GPIO4_99 Out J801:11 */ + {ABEDMIC_CLK1, (PTU | IEN | M6)}, /* GPIO4_100 In J801:14 */ + + {ABEDMIC_CLK2, (IEN | M1)}, /* ABEMCBSP1_FSX BT Aud */ + {ABEDMIC_CLK3, (M1)}, /* ABEMCBSP1_DX BT Aud */ + {ABESLIMBUS1_CLOCK, (IEN | M1)}, /* ABEMCBSP1_CLKX BT Aud */ + {ABESLIMBUS1_DATA, (IEN | M1)}, /* ABEMCBSP1_DR BT Aud */ + + {ABEMCBSP2_DR, (IEN | M0)}, /* ABEMCBSP2_DR FM Aud */ + {ABEMCBSP2_DX, (M0)}, /* ABEMCBSP2_DX FM Aud */ + {ABEMCBSP2_FSX, (IEN | M0)}, /* ABEMCBSP2_FSX FM Aud */ + {ABEMCBSP2_CLKX, (IEN | M0)}, /* ABEMCBSP2_CLKX FM Aud */ + + {ABEMCPDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_UL_DATA */ + {ABEMCPDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_DL_DATA */ + {ABEMCPDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_FRAME */ + {ABEMCPDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_LB_CLK */ + + {WLSDIO_CLK, (PTU | IEN | M0)}, /* WLSDIO_CLK */ + {WLSDIO_CMD, (PTU | IEN | M0)}, /* WLSDIO_CMD */ + {WLSDIO_DATA0, (PTU | IEN | M0)}, /* WLSDIO_DATA0 */ + {WLSDIO_DATA1, (PTU | IEN | M0)}, /* WLSDIO_DATA1 */ + {WLSDIO_DATA2, (PTU | IEN | M0)}, /* WLSDIO_DATA2 */ + {WLSDIO_DATA3, (PTU | IEN | M0)}, /* WLSDIO_DATA3 */ + + {UART5_RX, (PTU | IEN | M0)}, /* UART5_RX BT HCI */ + {UART5_TX, (M0)}, /* UART5_TX BT HCI */ + {UART5_CTS, (PTU | IEN | M0)}, /* UART5_CTS BT HCI */ + {UART5_RTS, (M0)}, /* UART5_RTS BT HCI */ + + {I2C2_SCL, (IEN | M0)}, /* I2C2_SCL */ + {I2C2_SDA, (IEN | M0)}, /* I2C2_SDA */ + + {MCSPI1_CLK, (PTD | M6)}, /* GPIO5_140 Out WLAN EN */ + {MCSPI1_SOMI, (PTD | M6)}, /* GPIO5_141 Out J802:17 */ + {MCSPI1_SIMO, (PTD | M6)}, /* GPIO5_142 Out BT EN */ + {MCSPI1_CS0, (PTD | M6)}, /* GPIO5_143 Out BT Wkup */ + {MCSPI1_CS1, (PTD | IEN | M6)}, /* GPIO5_144 In Host WU */ + + {I2C5_SCL, (IEN | PTU | M0)}, /* I2C5_SCL */ + {I2C5_SDA, (IEN | PTU | M0)}, /* I2C5_SDA */ + + {PERSLIMBUS2_CLOCK, (PTD | M6)}, /* GPIO5_145 Out AUDPWRON*/ + {PERSLIMBUS2_DATA, (PTD | M6)}, /* GPIO5_146 Out J802:27 */ + {UART6_TX, (PTD | M6)}, /* GPIO5_149 Out J802:13 */ + {UART6_RX, (PTU | IEN | M6)}, /* GPIO5_150 In J802:20 */ + {UART6_CTS, (PTU | IEN | M6)}, /* GPIO5_151 In J802:21 EXCEPTION TO RULE, SHORT WITH PIN 23 */ + {UART6_RTS, (PTD | M6)}, /* GPIO5_152 Out J802:19 */ + {UART3_CTS_RCTX, (PTD | IEN | M6)}, /* GPIO5_153 In J802:14 or SATA_ACTLED Out (M1). PTD! */ + {UART3_RTS_IRSD, (PTU | IEN | M6)}, /* GPIO5_154 In J802:16 */ + + {I2C1_PMIC_SCL, (PTU | IEN | M0)}, /* I2C1_PMIC_SCL */ + {I2C1_PMIC_SDA, (PTU | IEN | M0)}, /* I2C1_PMIC_SDA */ + +}; + +const struct pad_conf_entry wkup_padconf_array_non_essential[] = { + + {LLIA_WAKEREQIN, (PTU | IEN | M6)}, /* GPIO1_WK14 In J201:19 */ + {LLIB_WAKEREQIN, (PTU | IEN | M6)}, /* GPIO1_WK15 In J801:18 */ + {DRM_EMU0, (PTU | IEN | M0)}, /* DRM_EMU0 */ + {DRM_EMU1, (PTU | IEN | M0)}, /* DRM_EMU1 */ + {JTAG_NTRST, (IEN | M0)}, /* JTAG_NTRST */ + {JTAG_TCK, (IEN | M0)}, /* JTAG_TCK */ + {JTAG_RTCK, (M0)}, /* JTAG_RTCK */ + {JTAG_TMSC, (IEN | M0)}, /* JTAG_TMSC */ + {JTAG_TDI, (IEN | M0)}, /* JTAG_TDI */ + {JTAG_TDO, (M0)}, /* JTAG_TDO */ + {FREF_CLK_IOREQ, (PTU | IEN | M6)}, /* GPIO1_WK13 In ETH_WAKE */ + {FREF_CLK0_OUT, (M0)}, /* FREF_CLK0_OUT */ + {FREF_CLK1_OUT, (M0)}, /* FREF_CLK1_OUT */ + {FREF_CLK2_OUT, (M0)}, /* FREF_CLK2_OUT */ + {FREF_CLK2_REQ, (PTU | IEN | M6)}, /* GPIO1_WK9 In WiLink Int */ + {FREF_CLK1_REQ, (PTU | IEN | M6)}, /* GPIO1_WK8 In SH2_MSP_INT */ + {SYS_NRESPWRON, (IEN | M0)}, /* SYS_NRESPWRON */ + {SYS_NRESWARM, (PTU | IEN | M0)}, /* SYS_NRESWARM */ + {SYS_PWR_REQ, (M0)}, /* SYS_PWR_REQ */ + {SYS_NIRQ1, (PTU | IEN | M0)}, /* SYS_NIRQ1 */ + {SYS_NIRQ2, (PTU | IEN | M0)}, /* SYS_NIRQ2 */ + {SYS_BOOT0, (IEN | M0)}, /* SYS_BOOT0 */ + {SYS_BOOT1, (IEN | M0)}, /* SYS_BOOT1 */ + {SYS_BOOT2, (IEN | M0)}, /* SYS_BOOT2 */ + {SYS_BOOT3, (IEN | M0)}, /* SYS_BOOT3 */ + {SYS_BOOT4, (IEN | M0)}, /* SYS_BOOT4 */ + {SYS_BOOT5, (IEN | M0)}, /* SYS_BOOT5 */ + +}; + +#endif /* _SOM5_EVB_MUX_DATA_H */ + diff --git a/board/mms/som5_evb/som5_evb.c b/board/mms/som5_evb/som5_evb.c new file mode 100644 index 0000000..a84672e --- /dev/null +++ b/board/mms/som5_evb/som5_evb.c @@ -0,0 +1,200 @@ +/* + * Copyright (C) 2013 MM Solutions AD, <www.mm-sol.com> + * + * 02/2013 Derived from OMAP5 EVM and modified for the SOM5 EVB + * by Lubomir Popov lpopov@mm-sol.com l-popov@ti.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <twl6035.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/mmc_host_def.h> +#include <asm/gpio.h> +#include <asm/omap_common.h> + +#include "s5evb_mux_data.h" + +#ifdef CONFIG_USB_EHCI +#include <usb.h> +#include <asm/arch/ehci.h> +#include <asm/ehci-omap.h> +#endif + +DECLARE_GLOBAL_DATA_PTR; + +const struct omap_sysinfo sysinfo = { + "Board: MM Solutions SOM5 EVB\n" +}; + +/** + * @brief board_init + * + * @return 0 + */ +int board_init(void) +{ + gpmc_init(); + gd->bd->bi_arch_number = MACH_TYPE_SOM5_EVB; + gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */ + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + return 0; +} + +/** + * @brief misc_init_r - Configure SOM5 EVB board specific features + * such as power configurations, ethernet initialization as phase2 + * of boot sequence + * + * @return 0 + */ +int misc_init_r(void) +{ +#ifdef CONFIG_TWL6035_POWER + twl6035_init_settings(); +#ifdef CONFIG_TWL6035_AUDPWR + /* Useful for measuring voltages around the codec. + * Works with a TWL604x only. + */ + twl6035_audio_power(1); /* Power on 2.1 V SMPS, enable 32 kHz */ + udelay(1000); /* Allow ramp-up */ + /* Start TWL6040 internal power on sequence: */ + gpio_request(CONFIG_OMAP_AUDPWRON_GPIO, "AUDPWRON"); + gpio_direction_output(CONFIG_OMAP_AUDPWRON_GPIO, 1); +#endif +#ifdef CONFIG_BB_CHRG + /* Board has a 3 V super-cap for BB */ + twl6035_enable_bb_charge(BB_HIGH_ICHRG | BB_VSEL_3V0 | BB_CHRG_EN); +#endif +#endif /* CONFIG_TWL6035_POWER */ +#ifdef CONFIG_SYSCLK_OUT_EN + /* Enable FREF_XTAL_CLK output (19.2 MHz). + * Used as Audio MCLK; for measurement only. + * TODO: Use proper defines + * control_ckobuffer + */ + writel(0x10000000, 0x4ae0cdb4); +#endif + return 0; +} + +void set_muxconf_regs_essential(void) +{ + do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_essential, + sizeof(core_padconf_array_essential) / + sizeof(struct pad_conf_entry)); + + do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_essential, + sizeof(wkup_padconf_array_essential) / + sizeof(struct pad_conf_entry)); + + /* Set the MSECURE Mode for GPIO234 pin */ + if (get_device_type() == DEVICE_GP) { + u32 msecure_pad = CONTROL_PADCONF_CORE + GPIO8_234; + writew((readw(msecure_pad) & ~M7) | M1, msecure_pad); + } +#ifdef CONFIG_I2C_INTERNAL_PULLUPS + /* Enable internal I2C-compatible pullups on all buses + * TODO: Replace this ugly hardcoding with proper defines (omap.h) + * control_smart3io_padconf_0, control_i2c_0 + */ + writel(0x00554000, 0x4a002dc0); /* First set drive strength */ + writel(0, 0x4a002e04); /* Now enable pull-ups */ +#endif +} + +void set_muxconf_regs_non_essential(void) +{ + do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, + sizeof(core_padconf_array_non_essential) / + sizeof(struct pad_conf_entry)); + + do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, + sizeof(wkup_padconf_array_non_essential) / + sizeof(struct pad_conf_entry)); +} + +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) +int board_mmc_init(bd_t *bis) +{ + omap_mmc_init(0, 0, 0, -1, -1); + omap_mmc_init(1, 0, 0, -1, -1); + return 0; +} +#endif + +#ifdef CONFIG_USB_EHCI + +#define USB_HOST_HS_CLKCTRL_MASK 0x0100D7C0 /* CM_L3INIT_USB_HOST_HS_CLKCTRL */ +#define USB_TLL_HS_CLKCTRL_MASK 0x00000700 /* CM_L3INIT_USB_TLL_HS_CLKCTRL */ + +static struct omap_usbhs_board_data usbhs_bdata = { + .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, /* USBB1: ULPI PHY TUSB1210 */ + .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC, /* USBB2: HSIC USB4640 hub */ + .port_mode[2] = OMAP_EHCI_PORT_MODE_HSIC, /* USBB3: HSIC LAN9730 Ethernet ctrl */ +}; + +int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor) +{ + int ret; + + /* Enbale all 3 USB ports UHH, UTMI and HSIC clocks */ + setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, + USB_HOST_HS_CLKCTRL_MASK); + + /* Enbale all 3 USB host ports TLL clocks */ + setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl, + USB_TLL_HS_CLKCTRL_MASK); + + /* USBB1 ULPI PHY uses OMAP FREF_CLK0_OUT. Must turn it on. + * TODO: Replace this ugly hardcoding with proper defines + */ + writel(0x0100, 0x4ae0a310); + udelay(1000); /* Let PHY PLL lock */ + + ret = omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor); + if (ret < 0) + return ret; + + return 0; +} + +int ehci_hcd_stop(void) +{ + int ret; + + ret = omap_ehci_hcd_stop(); + + clrbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, + USB_HOST_HS_CLKCTRL_MASK); + clrbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl, + USB_TLL_HS_CLKCTRL_MASK); + + /* TODO: Replace this ugly hardcoding with proper defines + */ + writel(0, 0x4ae0a310); /* Stop FREF_CLK0_OUT */ + return ret; +} +#endif /* CONFIG_USB_EHCI */ + diff --git a/boards.cfg b/boards.cfg index 5fc70be..337dc42 100644 --- a/boards.cfg +++ b/boards.cfg @@ -292,6 +292,7 @@ twister arm armv7 twister technex nokia_rx51 arm armv7 rx51 nokia omap3 omap4_panda arm armv7 panda ti omap4 omap4_sdp4430 arm armv7 sdp4430 ti omap4 +omap5_som5_evb arm armv7 som5_evb mms omap5 omap5_evm arm armv7 omap5_evm ti omap5 dra7xx_evm arm armv7 dra7xx ti omap5 s5p_goni arm armv7 goni samsung s5pc1xx diff --git a/include/configs/omap5_som5_evb.h b/include/configs/omap5_som5_evb.h new file mode 100644 index 0000000..46a9c0c --- /dev/null +++ b/include/configs/omap5_som5_evb.h @@ -0,0 +1,336 @@ +/* + * Copyright (C) 2013 MM Solutions AD, <www.mm-sol.com> + * + * 02/2013 Derived from OMAP5 EVM and modified for the SOM5 EVB + * by Lubomir Popov lpopov@mm-sol.com l-popov@ti.com + * + * Configuration settings for the MMS SOM5 (APM-5) Evaluation Board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_ARMV7 /* This is an ARM V7 CPU core */ +#define CONFIG_OMAP /* in a TI OMAP core */ +#define CONFIG_OMAP54XX /* which is a 54XX */ +#define CONFIG_OMAP5430 /* which is in a 5430 */ +#define CONFIG_SOM5EVB /* working with the SOM5 EVB */ +/* Machine type for Linux */ +#define CONFIG_MACH_TYPE MACH_TYPE_SOM5_EVB + +#define CONFIG_OMAP_GPIO + +/* Get CPU defs */ +#include <asm/arch/cpu.h> +#include <asm/arch/omap.h> + +/* Display CPU and Board Info */ +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +/* Clock Defines */ +#define V_OSCK 19200000 /* Clock output from T2 */ +#define V_SCLK V_OSCK +/* Enable all clocks: */ +/*#define CONFIG_SYS_CLOCKS_ENABLE_ALL*/ + +#define CONFIG_SYS_ENABLE_PADS_ALL /* Enable all PADS for now */ + +#define CONFIG_MISC_INIT_R + +#define CONFIG_OF_LIBFDT +#define CONFIG_CMD_BOOTZ + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG + +/* + * Size of malloc() pool + * Total Size Environment - 128k + * Malloc - add 256k + */ +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10)) +/* Vector Base */ +#define CONFIG_SYS_CA15_VECTOR_BASE SRAM_ROM_VECT_BASE + +/* + * Hardware drivers + */ + +/* + * serial port - NS16550 compatible + */ +#define V_NS16550_CLK 48000000 + +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK +#define CONFIG_CONS_INDEX 3 +#define CONFIG_SYS_NS16550_COM3 UART3_BASE + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, \ + 57600, 115200} + +/* I2C */ +#define CONFIG_HARD_I2C +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0x00 /* Own slave addr */ +#define CONFIG_DRIVER_OMAP54XX_I2C +#define CONFIG_I2C_MULTI_BUS +/* MUST be defined if external pullups are not populated: */ +#define CONFIG_I2C_INTERNAL_PULLUPS +/* Define to use Repeated Start by i2c_read (otherwise Stop-Start + * shall be used between the address and data phases): + */ +#undef CONFIG_I2C_REPEATED_START +/* Used by i2c mm/mw; needed for correct write to EEPROM: */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* TWL6035 */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_TWL6035_POWER +/* Undef to disable forced PWM mode for the 1.8 V SMPS: */ +#define CONFIG_TWL6035_SMPS7_FPWM +/* Following define enables testing of the TWL6040 audio codec power + * supply environment: the PMIC 2.1 V SMPS, and the codec's internal + * REF, NCP and HS/LS LDOs. Undef to disable powering up codec. */ +#define CONFIG_TWL6035_AUDPWR + +#ifdef CONFIG_TWL6035_AUDPWR +#define CONFIG_OMAP_AUDPWRON_GPIO 145 +#endif +/* Undef to disable BB (super-cap) charging: */ +#define CONFIG_BB_CHRG +#endif /* CONFIG_SPL_BUILD */ + +/* For Audio MCLK test/measurement only; enables the + * OMAP5 FREF_XTAL_CLK output: */ +#define CONFIG_SYSCLK_OUT_EN + +/* MMC */ +#define CONFIG_GENERIC_MMC +#define CONFIG_MMC +#define CONFIG_OMAP_HSMMC +#define CONFIG_DOS_PARTITION + +/* MMC ENV related defines */ +#define CONFIG_ENV_IS_NOWHERE +#ifdef CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */ +#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_CMD_SAVEENV +#endif + +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +/* Flash */ +#define CONFIG_SYS_NO_FLASH + +/* Cache */ +#define CONFIG_SYS_CACHELINE_SIZE 64 +#define CONFIG_SYS_CACHELINE_SHIFT 6 + +/* USB UHH support options */ +#define CONFIG_CMD_USB +#define CONFIG_USB_HOST +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_OMAP +#define CONFIG_USB_ULPI +#define CONFIG_USB_ULPI_VIEWPORT_OMAP +#define CONFIG_USB_STORAGE +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 + +/* No signals to reset external PHYs on this board: */ +/*#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO xxx */ + +/* Due to HSIC connect ussues, device reset is required upon + * applying port power. A GPIO is needed per HSIC device: + */ +#define CONFIG_OMAP_HSIC_PORT2_RESET_GPIO 173 /* Combo hub */ +#define CONFIG_OMAP_HSIC_PORT3_RESET_GPIO 172 /* Ethernet Ctrlr */ + +/* USB Networking options */ + +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_SMSC95XX + +/* Commands to include */ +#include <config_cmd_default.h> + +/* Enabled commands */ +#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ +#define CONFIG_CMD_NFS /* NFS support */ +#define CONFIG_CMD_DHCP /* DHCP support */ +#define CONFIG_CMD_PING /* PING support */ +#define CONFIG_NET_MULTI + +#define CONFIG_CMD_EXT2 /* EXT2 support */ +#define CONFIG_CMD_FAT /* FAT support */ +#define CONFIG_CMD_I2C /* I2C serial bus support */ +#define CONFIG_CMD_MMC /* MMC support */ +#define CONFIG_CMD_GPIO /* GPIO support */ + +/* Disabled commands */ +#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ +#undef CONFIG_CMD_IMLS /* List all found images */ + +/* + * Environment setup + */ +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "usbethaddr=9e:77:39:1b:c4:2d\0" \ + "loadaddr=0x82000000\0" \ + "console=ttyO2,115200n8\0" \ + "usbtty=cdc_acm\0" \ + "vram=16M\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 rw\0" \ + "mmcrootfstype=ext3 rootwait\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "vram=${vram} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ + "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \ + "source ${loadaddr}\0" \ + "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ + "mmcboot=echo Booting from mmc${mmcdev} ...; " \ + "run mmcargs; " \ + "bootm ${loadaddr}\0" \ + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; " \ + "if mmc rescan ; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "fi; " \ + "fi; " \ + "fi " + +#define CONFIG_AUTO_COMPLETE 1 + +/* + * Miscellaneous configurable options + */ + +#define CONFIG_SYS_PROMPT "SOM5_EVB # " + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_CBSIZE 256 +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) + +/* + * memtest setup + */ +#define CONFIG_SYS_MEMTEST_START 0xb8000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (256 << 20)) +/* Undef following two for simple mtest */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_SCRATCH 0x81000000 + +/* Default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x80000000 + +/* Use General purpose timer 1 */ +#define CONFIG_SYS_TIMERBASE GPT2_BASE +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 + +/* + * SDRAM Memory Map + * Even though we use two CS all the memory + * is mapped to one contiguous block + */ +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 + +#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ + GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS + +/* Defines for SDRAM init */ +#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS +#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION +#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS +#endif + +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x40300350 +#define CONFIG_SPL_MAX_SIZE 0x19000 /* 100K */ +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#define CONFIG_SPL_DISPLAY_PRINT + +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" + +/* + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x80E7FFC0--0x80E80000 should not be used for any + * other needs. + */ +#define CONFIG_SYS_TEXT_BASE 0x80E80000 + +/* + * BSS and malloc area 64MB into memory to allow enough + * space for the kernel at the beginning of memory + */ +#define CONFIG_SPL_BSS_START_ADDR 0x84000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */ +#define CONFIG_SYS_SPL_MALLOC_START 0x84100000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ +#define CONFIG_SPL_GPIO_SUPPORT + +#endif /* __CONFIG_H */