This patch add I2C support for Freescale MX53 processor

Signed-off-by: Jason Liu r64343@freescale.com

--- Changes for v2: -address the comments of Heiko, add #if defined(CONFIG_MX31) to avoid break MX31 build. Move CONFIG_HARD_I2C to the top of the file and fix the error message from: #error "define CONFIG_SYS_I2C_PORT to use the I2C driver" to #error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver"

Changes for v3: -address the comments from Albert, change #ifdef to #if defined() for the sake of homogeneity --- drivers/i2c/mxc_i2c.c | 21 ++++++++++++++++++--- 1 files changed, 18 insertions(+), 3 deletions(-)

diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c old mode 100644 new mode 100755 index 8e10fbb..1ebec14 --- a/drivers/i2c/mxc_i2c.c +++ b/drivers/i2c/mxc_i2c.c @@ -26,8 +26,14 @@

#if defined(CONFIG_HARD_I2C)

+#if defined(CONFIG_MX31) #include <asm/arch/mx31.h> #include <asm/arch/mx31-regs.h> +#endif + +#if defined(CONFIG_MX53) +#include <asm/arch/clock.h> +#endif

#define IADR 0x00 #define IFDR 0x04 @@ -47,7 +53,7 @@ #define I2SR_IIF (1 << 1) #define I2SR_RX_NO_AK (1 << 0)

-#ifdef CONFIG_SYS_I2C_MX31_PORT1 +#if defined(CONFIG_SYS_I2C_MX31_PORT1) #define I2C_BASE 0x43f80000 #define I2C_CLK_OFFSET 26 #elif defined (CONFIG_SYS_I2C_MX31_PORT2) @@ -56,8 +62,12 @@ #elif defined (CONFIG_SYS_I2C_MX31_PORT3) #define I2C_BASE 0x43f84000 #define I2C_CLK_OFFSET 30 +#elif defined(CONFIG_SYS_I2C_MX53_PORT1) +#define I2C_BASE I2C1_BASE_ADDR +#elif defined(CONFIG_SYS_I2C_MX53_PORT2) +#define I2C_BASE I2C2_BASE_ADDR #else -#error "define CONFIG_SYS_I2C_MX31_PORTx to use the mx31 I2C driver" +#error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver" #endif

#ifdef DEBUG @@ -72,11 +82,16 @@ static u16 div[] = { 30, 32, 36, 42, 48, 52, 60, 72, 80, 88, 104, 128, 144,

void i2c_init(int speed, int unused) { - int freq = mx31_get_ipg_clk(); + int freq; int i;

+#if defined(CONFIG_MX31) + freq = mx31_get_ipg_clk(); /* start the required I2C clock */ __REG(CCM_CGR0) = __REG(CCM_CGR0) | (3 << I2C_CLK_OFFSET); +#else + freq = mxc_get_clock(MXC_IPG_PERCLK); +#endif

for (i = 0; i < 0x1f; i++) if (freq / div[i] <= speed)