U-Boot support for the CL-SOM-AM57x module is no longer required.

Signed-off-by: Uri Mashiach uri.mashiach@compulab.co.il --- arch/arm/dts/am57xx-cl-som-am57x.dts | 617 ----------------------------- arch/arm/dts/am57xx-sbc-am57x.dts | 179 --------- arch/arm/mach-omap2/omap5/Kconfig | 5 - board/compulab/cl-som-am57x/Kconfig | 12 - board/compulab/cl-som-am57x/MAINTAINERS | 6 - board/compulab/cl-som-am57x/Makefile | 17 - board/compulab/cl-som-am57x/cl-som-am57x.c | 78 ---- board/compulab/cl-som-am57x/eth.c | 198 --------- board/compulab/cl-som-am57x/mux.c | 123 ------ board/compulab/cl-som-am57x/spl.c | 238 ----------- configs/cl-som-am57x_defconfig | 64 --- include/configs/cl-som-am57x.h | 148 ------- 12 files changed, 1685 deletions(-) delete mode 100644 arch/arm/dts/am57xx-cl-som-am57x.dts delete mode 100644 arch/arm/dts/am57xx-sbc-am57x.dts delete mode 100644 board/compulab/cl-som-am57x/Kconfig delete mode 100644 board/compulab/cl-som-am57x/MAINTAINERS delete mode 100644 board/compulab/cl-som-am57x/Makefile delete mode 100644 board/compulab/cl-som-am57x/cl-som-am57x.c delete mode 100644 board/compulab/cl-som-am57x/eth.c delete mode 100644 board/compulab/cl-som-am57x/mux.c delete mode 100644 board/compulab/cl-som-am57x/spl.c delete mode 100644 configs/cl-som-am57x_defconfig delete mode 100644 include/configs/cl-som-am57x.h

diff --git a/arch/arm/dts/am57xx-cl-som-am57x.dts b/arch/arm/dts/am57xx-cl-som-am57x.dts deleted file mode 100644 index 203266f884..0000000000 --- a/arch/arm/dts/am57xx-cl-som-am57x.dts +++ /dev/null @@ -1,617 +0,0 @@ -/* - * Support for CompuLab CL-SOM-AM57x System-on-Module - * - * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/ - * Author: Dmitry Lifshitz lifshitz@compulab.co.il - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License version 2 as published by - * the Free Software Foundation. - */ - -/dts-v1/; - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/interrupt-controller/irq.h> -#include "dra74x.dtsi" - -/ { - model = "CompuLab CL-SOM-AM57x"; - compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7"; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x80000000 0x0 0x20000000>; /* 512 MB - minimal configuration */ - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&leds_pins_default>; - - led0 { - label = "cl-som-am57x:green"; - gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - }; - - vdd_3v3: fixedregulator-vdd_3v3 { - compatible = "regulator-fixed"; - regulator-name = "vdd_3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - ads7846reg: fixedregulator-ads7846-reg { - compatible = "regulator-fixed"; - regulator-name = "ads7846-reg"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - sound0: sound0 { - compatible = "simple-audio-card"; - simple-audio-card,name = "CL-SOM-AM57x-Sound-Card"; - simple-audio-card,format = "i2s"; - simple-audio-card,bitclock-master = <&dailink0_master>; - simple-audio-card,frame-master = <&dailink0_master>; - simple-audio-card,widgets = - "Headphone", "Headphone Jack", - "Microphone", "Microphone Jack", - "Line", "Line Jack"; - simple-audio-card,routing = - "Headphone Jack", "RHPOUT", - "Headphone Jack", "LHPOUT", - "LLINEIN", "Line Jack", - "MICIN", "Mic Bias", - "Mic Bias", "Microphone Jack"; - - dailink0_master: simple-audio-card,cpu { - sound-dai = <&mcasp3>; - }; - - simple-audio-card,codec { - sound-dai = <&wm8731>; - system-clock-frequency = <12000000>; - }; - }; -}; - -&dra7_pmx_core { - leds_pins_default: leds_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x347c, PIN_OUTPUT | MUX_MODE14) /* gpmc_a15.gpio2_5 */ - >; - }; - - i2c1_pins_default: i2c1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */ - DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */ - >; - }; - - i2c3_pins_default: i2c3_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */ - DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */ - >; - }; - - i2c4_pins_default: i2c4_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36ac, PIN_INPUT| MUX_MODE10) /* mcasp1_acl.i2c4_sda */ - DRA7XX_CORE_IOPAD(0x36b0, PIN_INPUT| MUX_MODE10) /* mcasp1_fsr.i2c4_scl */ - >; - }; - - tps659038_pins_default: tps659038_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */ - >; - }; - - mmc2_pins_default: mmc2_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ - DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ - DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ - DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ - DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ - DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ - DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ - DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ - DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ - DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ - >; - }; - - qspi1_pins: pinmux_qspi1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3474, PIN_INPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ - DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d0 */ - DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d1 */ - DRA7XX_CORE_IOPAD(0x3488, PIN_INPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ - DRA7XX_CORE_IOPAD(0x34b8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ - DRA7XX_CORE_IOPAD(0x34bc, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ - >; - }; - - cpsw_pins_default: cpsw_pins_default { - pinctrl-single,pins = < - /* Slave at addr 0x0 */ - DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii0_tclk */ - DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii0_tctl */ - DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td3 */ - DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td2 */ - DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td1 */ - DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td0 */ - DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rclk */ - DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rctl */ - DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd3 */ - DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd2 */ - DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd1 */ - DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rgmii0_rd0 */ - - /* Slave at addr 0x1 */ - DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_tclk */ - DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ - DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ - DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ - DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ - DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ - DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ - DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ - DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ - DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ - DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ - >; - }; - - cpsw_pins_sleep: cpsw_pins_sleep { - pinctrl-single,pins = < - /* Slave 1 */ - DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15) - - /* Slave 2 */ - DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15) - >; - }; - - davinci_mdio_pins_default: davinci_mdio_pins_default { - pinctrl-single,pins = < - /* MDIO */ - DRA7XX_CORE_IOPAD(0x3590, PIN_OUTPUT_PULLUP | MUX_MODE3)/* vin2a_d10.mdio_mclk */ - DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT_PULLUP | MUX_MODE3) /* vin2a_d11.mdio_d */ - >; - }; - - davinci_mdio_pins_sleep: davinci_mdio_pins_sleep { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3590, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT | MUX_MODE15) - >; - }; - - ads7846_pins: pinmux_ads7846_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3464, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpmc_a9.gpio1_31 */ - >; - }; - - mcasp3_pins_default: mcasp3_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */ - DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */ - DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */ - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */ - >; - }; - - mcasp3_pins_sleep: mcasp3_pins_sleep { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15) - >; - }; -}; - -&i2c1 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_default>; - clock-frequency = <400000>; -}; - -&i2c3 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_pins_default>; - clock-frequency = <400000>; -}; - -&i2c4 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c4_pins_default>; - clock-frequency = <400000>; - - tps659038: tps659038@58 { - compatible = "ti,tps659038"; - reg = <0x58>; - interrupt-parent = <&gpio1>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - - pinctrl-names = "default"; - pinctrl-0 = <&tps659038_pins_default>; - - #interrupt-cells = <2>; - interrupt-controller; - - ti,system-power-controller; - - tps659038_pmic { - compatible = "ti,tps659038-pmic"; - - regulators { - smps12_reg: smps12 { - /* VDD_MPU */ - regulator-name = "smps12"; - regulator-min-microvolt = < 850000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-boot-on; - }; - - smps3_reg: smps3 { - /* VDD_DDR */ - regulator-name = "smps3"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; - }; - - smps45_reg: smps45 { - /* VDD_DSPEVE */ - regulator-name = "smps45"; - regulator-min-microvolt = < 850000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-boot-on; - }; - - smps6_reg: smps6 { - /* VDD_GPU */ - regulator-name = "smps6"; - regulator-min-microvolt = < 850000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-boot-on; - }; - - smps7_reg: smps7 { - /* VDD_CORE */ - regulator-name = "smps7"; - regulator-min-microvolt = < 850000>; - regulator-max-microvolt = <1160000>; - regulator-always-on; - regulator-boot-on; - }; - - smps8_reg: smps8 { - /* VDD_IVA */ - regulator-name = "smps8"; - regulator-min-microvolt = < 850000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-boot-on; - }; - - smps9_reg: smps9 { - /* PMIC_3V3 */ - regulator-name = "smps9"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - - ldo1_reg: ldo1 { - /* VDD_SD / VDDSHV8 */ - regulator-name = "ldo1"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo2_reg: ldo2 { - /* VDD_1V8 */ - regulator-name = "ldo2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo3_reg: ldo3 { - /* VDDA_1V8_PHYA - supplies VDDA_SATA, VDDA_USB1/2/3 */ - regulator-name = "ldo3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo4_reg: ldo4 { - /* VDDA_1V8_PHYB - supplies VDDA_HDMI, VDDA_PCIE/0/1 */ - regulator-name = "ldo4"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo9_reg: ldo9 { - /* VDD_RTC */ - regulator-name = "ldo9"; - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1050000>; - regulator-always-on; - regulator-boot-on; - }; - - ldoln_reg: ldoln { - /* VDDA_1V8_PLL */ - regulator-name = "ldoln"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldousb_reg: ldousb { - /* VDDA_3V_USB: VDDA_USBHS33 */ - regulator-name = "ldousb"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - /* regen1 not used */ - }; - }; - - tps659038_pwr_button: tps659038_pwr_button { - compatible = "ti,palmas-pwrbutton"; - interrupt-parent = <&tps659038>; - interrupts = <1 IRQ_TYPE_EDGE_FALLING>; - wakeup-source; - ti,palmas-long-press-seconds = <12>; - }; - - tps659038_gpio: tps659038_gpio { - compatible = "ti,palmas-gpio"; - gpio-controller; - #gpio-cells = <2>; - }; - }; - - rtc0: rtc@56 { - compatible = "emmicro,em3027"; - reg = <0x56>; - }; - - eeprom_module: atmel@50 { - compatible = "atmel,24c08"; - reg = <0x50>; - pagesize = <16>; - }; - - wm8731: wm8731@1a { - #sound-dai-cells = <0>; - compatible = "wlf,wm8731"; - reg = <0x1a>; - status = "okay"; - }; -}; - -&cpu0 { - cpu0-supply = <&smps12_reg>; - voltage-tolerance = <1>; -}; - -&sata { - status = "okay"; -}; - -&mailbox5 { - status = "okay"; - mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { - status = "okay"; - }; - mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { - status = "okay"; - }; -}; - -&mailbox6 { - status = "okay"; - mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { - status = "okay"; - }; - mbox_dsp2_ipc3x: mbox_dsp2_ipc3x { - status = "okay"; - }; -}; - -&mmc2 { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_pins_default>; - - vmmc-supply = <&vdd_3v3>; - bus-width = <8>; - ti,non-removable; - cap-mmc-dual-data-rate; -}; - -&qspi { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&qspi1_pins>; - - spi-max-frequency = <48000000>; - - spi_flash: spi_flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "spansion,m25p80", "jedec,spi-nor"; - reg = <0>; /* CS0 */ - spi-max-frequency = <48000000>; - - partition@0 { - label = "uboot"; - reg = <0x0 0xc0000>; - }; - - partition@c0000 { - label = "uboot environment"; - reg = <0xc0000 0x40000>; - }; - - partition@100000 { - label = "reserved"; - reg = <0x100000 0x0>; - }; - }; - - /* touch controller */ - ads7846@0 { - pinctrl-names = "default"; - pinctrl-0 = <&ads7846_pins>; - - compatible = "ti,ads7846"; - vcc-supply = <&ads7846reg>; - - reg = <1>; /* CS1 */ - spi-max-frequency = <1500000>; - - interrupt-parent = <&gpio1>; - interrupts = <31 0>; - pendown-gpio = <&gpio1 31 0>; - - - ti,x-min = /bits/ 16 <0x0>; - ti,x-max = /bits/ 16 <0x0fff>; - ti,y-min = /bits/ 16 <0x0>; - ti,y-max = /bits/ 16 <0x0fff>; - - ti,x-plate-ohms = /bits/ 16 <180>; - ti,pressure-max = /bits/ 16 <255>; - - ti,debounce-max = /bits/ 16 <30>; - ti,debounce-tol = /bits/ 16 <10>; - ti,debounce-rep = /bits/ 16 <1>; - - wakeup-source; - }; -}; - -&mac { - status = "okay"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&cpsw_pins_default>; - pinctrl-1 = <&cpsw_pins_sleep>; - dual_emac; -}; - -&cpsw_emac0 { - phy_id = <&davinci_mdio>, <0>; - phy-mode = "rgmii-txid"; - dual_emac_res_vlan = <0>; -}; - -&cpsw_emac1 { - phy_id = <&davinci_mdio>, <1>; - phy-mode = "rgmii-txid"; - dual_emac_res_vlan = <1>; -}; - -&davinci_mdio { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&davinci_mdio_pins_default>; - pinctrl-1 = <&davinci_mdio_pins_sleep>; -}; - -&usb2_phy1 { - phy-supply = <&ldousb_reg>; -}; - -&usb2_phy2 { - phy-supply = <&ldousb_reg>; -}; - -&usb1 { - dr_mode = "host"; -}; - -&usb2 { - dr_mode = "host"; -}; - -&mcasp3 { - #sound-dai-cells = <0>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mcasp3_pins_default>; - pinctrl-1 = <&mcasp3_pins_sleep>; - status = "okay"; - - op-mode = <0>; /* MCASP_IIS_MODE */ - tdm-slots = <2>; - /* 4 serializers */ - serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ - 1 2 0 0 - >; -}; - -&gpio3 { - status = "okay"; - ti,no-reset-on-init; -}; - -&gpio2 { - status = "okay"; - ti,no-reset-on-init; -}; diff --git a/arch/arm/dts/am57xx-sbc-am57x.dts b/arch/arm/dts/am57xx-sbc-am57x.dts deleted file mode 100644 index 31f9be6324..0000000000 --- a/arch/arm/dts/am57xx-sbc-am57x.dts +++ /dev/null @@ -1,179 +0,0 @@ -/* - * Support for CompuLab SBC-AM57x single board computer - * - * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/ - * Author: Dmitry Lifshitz lifshitz@compulab.co.il - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License version 2 as published by - * the Free Software Foundation. - */ - -#include "am57xx-cl-som-am57x.dts" -#include "compulab-sb-som.dtsi" - -/ { - model = "CompuLab CL-SOM-AM57x on SB-SOM-AM57x"; - compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7"; - - aliases { - display0 = &lcd0; - display1 = &hdmi; - }; -}; - -&dra7_pmx_core { - uart3_pins_default: uart3_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */ - DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ - >; - }; - - mmc1_pins_default: mmc1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ - DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ - DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1_sdcd.gpio6_27 */ - DRA7XX_CORE_IOPAD(0x377c, PIN_INPUT | MUX_MODE14) /* mmc1_sdwp.gpio6_28 */ - >; - }; - - usb1_pins: pinmux_usb1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ - >; - }; - - i2c5_pins_default: i2c5_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT| MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT| MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ - >; - }; - - lcd_pins_default: lcd_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3564, PIN_OUTPUT | MUX_MODE14) /* vin2a_vsync0.gpio4_0 */ - >; - }; - - hdmi_pins: pinmux_hdmi_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ - DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ - >; - }; - - hdmi_conn_pins: pinmux_hdmi_conn_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT | MUX_MODE14) /* spi1_cs2.gpio7_12 */ - >; - }; -}; - -&uart3 { - status = "okay"; - interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, - <&dra7_pmx_core 0x3f8>; - - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins_default>; -}; - -&mmc1 { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_default>; - - vmmc-supply = <&ldo1_reg>; - bus-width = <4>; - cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; - wp-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>; -}; - -&usb1 { - pinctrl-names = "default"; - pinctrl-0 = <&usb1_pins>; -}; - -&i2c5 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c5_pins_default>; - clock-frequency = <400000>; - - eeprom_base: atmel@54 { - compatible = "atmel,24c08"; - reg = <0x54>; - pagesize = <16>; - }; - - pca9555: pca9555@20 { - compatible = "nxp,pca9555"; - reg = <0x20>; - gpio-controller; - #gpio-cells = <2>; - }; -}; - -&dss { - status = "ok"; - - vdda_video-supply = <&ldoln_reg>; - - port { - dpi_lcd_out: endpoint { - remote-endpoint = <&lcd_in>; - data-lines = <24>; - }; - }; -}; - -&lcd0 { - pinctrl-names = "default"; - pinctrl-0 = <&lcd_pins_default>; - - enable-gpios = <&pca9555 14 GPIO_ACTIVE_HIGH - &gpio4 0 GPIO_ACTIVE_HIGH>; - - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_lcd_out>; - data-lines = <24>; - }; - }; -}; - -&hdmi { - status = "ok"; - vdda-supply = <&ldo4_reg>; - - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_pins>; - - port { - hdmi_out: endpoint { - remote-endpoint = <&hdmi_connector_in>; - lanes = <1 0 3 2 5 4 7 6>; - }; - }; -}; - -&hdmi_conn { - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_conn_pins>; - - hpd-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&hdmi_out>; - }; - }; -}; diff --git a/arch/arm/mach-omap2/omap5/Kconfig b/arch/arm/mach-omap2/omap5/Kconfig index f083a4a385..fddbac9dec 100644 --- a/arch/arm/mach-omap2/omap5/Kconfig +++ b/arch/arm/mach-omap2/omap5/Kconfig @@ -9,10 +9,6 @@ choice prompt "OMAP5 board select" optional

-config TARGET_CL_SOM_AM57X - bool "CompuLab CL-SOM-AM57x" - select DRA7XX - config TARGET_CM_T54 bool "CompuLab CM-T54"

@@ -160,7 +156,6 @@ endchoice endmenu endif

-source "board/compulab/cl-som-am57x/Kconfig" source "board/compulab/cm_t54/Kconfig" source "board/ti/omap5_uevm/Kconfig" source "board/ti/dra7xx/Kconfig" diff --git a/board/compulab/cl-som-am57x/Kconfig b/board/compulab/cl-som-am57x/Kconfig deleted file mode 100644 index 85fc9a1fdb..0000000000 --- a/board/compulab/cl-som-am57x/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_CL_SOM_AM57X - -config SYS_BOARD - default "cl-som-am57x" - -config SYS_VENDOR - default "compulab" - -config SYS_CONFIG_NAME - default "cl-som-am57x" - -endif diff --git a/board/compulab/cl-som-am57x/MAINTAINERS b/board/compulab/cl-som-am57x/MAINTAINERS deleted file mode 100644 index e0195f4610..0000000000 --- a/board/compulab/cl-som-am57x/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -CL-SOM-AM57x BOARD -M: Uri Mashiach uri.mashiach@compulab.co.il -S: Maintained -F: board/compulab/cl-som-am57x/ -F: include/configs/cl-som-am57x.h -F: configs/cl-som-am57x_defconfig diff --git a/board/compulab/cl-som-am57x/Makefile b/board/compulab/cl-som-am57x/Makefile deleted file mode 100644 index 566366bf6e..0000000000 --- a/board/compulab/cl-som-am57x/Makefile +++ /dev/null @@ -1,17 +0,0 @@ -# -# Makefile -# -# (C) Copyright 2016 CompuLab, Ltd. <www.compulab.co.il> -# -# Author: Dmitry Lifshitz lifshitz@compulab.co.il -# -# SPDX-License-Identifier: GPL-2.0+ -# - -ifdef CONFIG_SPL_BUILD -obj-y += spl.o mux.o -else -obj-y += cl-som-am57x.o mux.o -endif - -obj-$(CONFIG_DRIVER_TI_CPSW) += eth.o diff --git a/board/compulab/cl-som-am57x/cl-som-am57x.c b/board/compulab/cl-som-am57x/cl-som-am57x.c deleted file mode 100644 index fcba2a0e2a..0000000000 --- a/board/compulab/cl-som-am57x/cl-som-am57x.c +++ /dev/null @@ -1,78 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Board functions for CompuLab cl_som_am57x board - * - * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/ - * - * Author: Dmitry Lifshitz lifshitz@compulab.co.il - */ - -#include <common.h> -#include <palmas.h> -#include <usb.h> -#include <asm/gpio.h> -#include <asm/arch/mmc_host_def.h> -#include <asm/arch/sys_proto.h> -#include "../common/common.h" -#include "../common/eeprom.h" -#include <asm/omap_common.h> - -DECLARE_GLOBAL_DATA_PTR; - -const struct omap_sysinfo sysinfo = { - "Board: CL-SOM-AM57x\n" -}; - -int board_init(void) -{ - /* Disable PMIC Powerhold feature, DEV_CTRL.DEV_ON = 1 */ - palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1); - - gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; - - return 0; -} - -#ifdef CONFIG_MMC -#define SB_SOM_CD_GPIO 187 -#define SB_SOM_WP_GPIO 188 - -int board_mmc_init(bd_t *bis) -{ - int ret0, ret1; - - ret0 = omap_mmc_init(0, 0, 0, SB_SOM_CD_GPIO, SB_SOM_WP_GPIO); - if (ret0) - printf("cl-som-am57x: failed to initialize mmc0\n"); - - ret1 = omap_mmc_init(1, 0, 0, -1, -1); - if (ret1) - printf("cl-som-am57x: failed to initialize mmc1\n"); - - return ret0 && ret1; -} -#endif /* CONFIG_MMC */ - -int misc_init_r(void) -{ - cl_print_pcb_info(); - - return 0; -} - -u32 get_board_rev(void) -{ - return cl_eeprom_get_board_rev(CONFIG_SYS_I2C_EEPROM_BUS); -} - -int board_usb_init(int index, enum usb_init_type init) -{ - enable_usb_clocks(index); - return 0; -} - -int board_usb_cleanup(int index, enum usb_init_type init) -{ - disable_usb_clocks(index); - return 0; -} diff --git a/board/compulab/cl-som-am57x/eth.c b/board/compulab/cl-som-am57x/eth.c deleted file mode 100644 index 3c59457341..0000000000 --- a/board/compulab/cl-som-am57x/eth.c +++ /dev/null @@ -1,198 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Ethernet specific code for CompuLab CL-SOM-AM57x module - * - * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/ - * - * Author: Uri Mashiach uri.mashiach@compulab.co.il - */ - -#include <common.h> -#include <cpsw.h> -#include <environment.h> -#include <miiphy.h> -#include <asm/gpio.h> -#include <asm/arch/sys_proto.h> -#include "../common/eeprom.h" - -static void cpsw_control(int enabled) -{ - /* VTP can be added here */ -} - -static struct cpsw_slave_data cl_som_am57x_cpsw_slaves[] = { - { - .slave_reg_ofs = 0x208, - .sliver_reg_ofs = 0xd80, - .phy_addr = 0, - .phy_if = PHY_INTERFACE_MODE_RMII, - }, - { - .slave_reg_ofs = 0x308, - .sliver_reg_ofs = 0xdc0, - .phy_addr = 1, - .phy_if = PHY_INTERFACE_MODE_RMII, - - }, -}; - -static struct cpsw_platform_data cl_som_am57_cpsw_data = { - .mdio_base = CPSW_MDIO_BASE, - .cpsw_base = CPSW_BASE, - .mdio_div = 0xff, - .channels = 8, - .cpdma_reg_ofs = 0x800, - .slaves = 2, - .slave_data = cl_som_am57x_cpsw_slaves, - .ale_reg_ofs = 0xd00, - .ale_entries = 1024, - .host_port_reg_ofs = 0x108, - .hw_stats_reg_ofs = 0x900, - .bd_ram_ofs = 0x2000, - .mac_control = (1 << 5), - .control = cpsw_control, - .host_port_num = 0, - .version = CPSW_CTRL_VERSION_2, -}; - -/* - * cl_som_am57x_efuse_read_mac_addr() - read Ethernet port MAC address. - * The information is retrieved from the SOC's registers. - * @buff: read buffer. - * @port_num: port number. - */ -static void cl_som_am57x_efuse_read_mac_addr(uchar *buff, uint port_num) -{ - uint32_t mac_hi, mac_lo; - - if (port_num) { - mac_lo = readl((*ctrl)->control_core_mac_id_1_lo); - mac_hi = readl((*ctrl)->control_core_mac_id_1_hi); - } else { - mac_lo = readl((*ctrl)->control_core_mac_id_0_lo); - mac_hi = readl((*ctrl)->control_core_mac_id_0_hi); - } - - buff[0] = (mac_hi & 0xFF0000) >> 16; - buff[1] = (mac_hi & 0xFF00) >> 8; - buff[2] = mac_hi & 0xFF; - buff[3] = (mac_lo & 0xFF0000) >> 16; - buff[4] = (mac_lo & 0xFF00) >> 8; - buff[5] = mac_lo & 0xFF; -} - -/* - * cl_som_am57x_handle_mac_address() - set MAC address in the U-Boot - * environment. - * The address is retrieved retrieved from an EEPROM field or from the - * SOC's registers. - * @env_name: U-Boot environment name. - * @field_name: EEPROM field name. - * @port_num: SOC's port number. - */ -static int cl_som_am57x_handle_mac_address(char *env_name, uint port_num) -{ - int ret; - uint8_t enetaddr[6]; - - ret = eth_env_get_enetaddr(env_name, enetaddr); - if (ret) - return 0; - - ret = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS); - - if (ret || !is_valid_ethaddr(enetaddr)) - cl_som_am57x_efuse_read_mac_addr(enetaddr, port_num); - - if (!is_valid_ethaddr(enetaddr)) - return -1; - - ret = eth_env_set_enetaddr(env_name, enetaddr); - if (ret) - printf("cl-som-am57x: Failed to set Eth port %d MAC address\n", - port_num); - - return ret; -} - -#define CL_SOM_AM57X_PHY_ADDR2 0x01 -#define AR8033_PHY_DEBUG_ADDR_REG 0x1d -#define AR8033_PHY_DEBUG_DATA_REG 0x1e -#define AR8033_DEBUG_RGMII_RX_CLK_DLY_REG 0x00 -#define AR8033_DEBUG_RGMII_TX_CLK_DLY_REG 0x05 -#define AR8033_DEBUG_RGMII_RX_CLK_DLY_MASK (1 << 15) -#define AR8033_DEBUG_RGMII_TX_CLK_DLY_MASK (1 << 8) - -/* - * cl_som_am57x_rgmii_clk_delay() - Set RGMII clock delay. - * Enable RX delay, disable TX delay. - */ -static void cl_som_am57x_rgmii_clk_delay(void) -{ - uint16_t mii_reg_val; - const char *devname; - - devname = miiphy_get_current_dev(); - /* PHY 2 */ - miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_ADDR_REG, - AR8033_DEBUG_RGMII_RX_CLK_DLY_REG); - miiphy_read(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG, - &mii_reg_val); - mii_reg_val |= AR8033_DEBUG_RGMII_RX_CLK_DLY_MASK; - miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG, - mii_reg_val); - - miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_ADDR_REG, - AR8033_DEBUG_RGMII_TX_CLK_DLY_REG); - miiphy_read(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG, - &mii_reg_val); - mii_reg_val &= ~AR8033_DEBUG_RGMII_TX_CLK_DLY_MASK; - miiphy_write(devname, CL_SOM_AM57X_PHY_ADDR2, AR8033_PHY_DEBUG_DATA_REG, - mii_reg_val); -} - -#define CL_SOM_AM57X_GPIO_PHY1_RST 92 /* GPIO3_28 */ -#define CL_SOM_AM57X_RGMII_PORT1 1 - -int board_eth_init(bd_t *bis) -{ - int ret; - uint32_t ctrl_val; - char *cpsw_phy_envval; - int cpsw_act_phy = 1; - - /* SB-SOM-AM57x primary Eth (P21) is routed to RGMII1 */ - ret = cl_som_am57x_handle_mac_address("ethaddr", - CL_SOM_AM57X_RGMII_PORT1); - - if (ret) - return -1; - - /* Select RGMII for GMII1_SEL */ - ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33); - ctrl_val |= 0x22; - writel(ctrl_val, (*ctrl)->control_core_control_io1); - mdelay(10); - - gpio_request(CL_SOM_AM57X_GPIO_PHY1_RST, "phy1_rst"); - gpio_direction_output(CL_SOM_AM57X_GPIO_PHY1_RST, 0); - mdelay(20); - - gpio_set_value(CL_SOM_AM57X_GPIO_PHY1_RST, 1); - mdelay(20); - - cpsw_phy_envval = env_get("cpsw_phy"); - if (cpsw_phy_envval != NULL) - cpsw_act_phy = simple_strtoul(cpsw_phy_envval, NULL, 0); - - cl_som_am57_cpsw_data.active_slave = cpsw_act_phy; - - ret = cpsw_register(&cl_som_am57_cpsw_data); - if (ret < 0) - printf("Error %d registering CPSW switch\n", ret); - - /* Set RGMII clock delay */ - cl_som_am57x_rgmii_clk_delay(); - - return ret; -} diff --git a/board/compulab/cl-som-am57x/mux.c b/board/compulab/cl-som-am57x/mux.c deleted file mode 100644 index 050f2aa3ef..0000000000 --- a/board/compulab/cl-som-am57x/mux.c +++ /dev/null @@ -1,123 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Pinmux configuration for CompuLab CL-SOM-AM57x board - * - * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/ - * - * Author: Dmitry Lifshitz lifshitz@compulab.co.il - */ -#include <asm/arch/sys_proto.h> -#include <asm/arch/mux_dra7xx.h> - -/* Serial console */ -static const struct pad_conf_entry cl_som_am57x_padconf_console[] = { - {UART3_RXD, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)}, /* UART3_RXD */ - {UART3_TXD, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)}, /* UART3_TXD */ -}; - -/* PMIC I2C */ -static const struct pad_conf_entry cl_som_am57x_padconf_pmic[] = { - {MCASP1_ACLKR, (M10 | PIN_INPUT)}, /* MCASP1_ACLKR.I2C4_SDA */ - {MCASP1_FSR, (M10 | PIN_INPUT)}, /* MCASP1_FSR.I2C4_SCL */ -}; - -/* Green GPIO led */ -static const struct pad_conf_entry cl_som_am57x_padconf_green_led[] = { - {GPMC_A15, (M14 | PIN_OUTPUT_PULLDOWN)}, /* GPMC_A15.GPIO2_5 */ -}; - -/* MMC/SD Card */ -static const struct pad_conf_entry cl_som_am57x_padconf_sd_card[] = { - {MMC1_CLK, (M0 | PIN_INPUT_PULLUP)}, /* MMC1_CLK */ - {MMC1_CMD, (M0 | PIN_INPUT_PULLUP)}, /* MMC1_CMD */ - {MMC1_DAT0, (M0 | PIN_INPUT_PULLUP)}, /* MMC1_DAT0 */ - {MMC1_DAT1, (M0 | PIN_INPUT_PULLUP)}, /* MMC1_DAT1 */ - {MMC1_DAT2, (M0 | PIN_INPUT_PULLUP)}, /* MMC1_DAT2 */ - {MMC1_DAT3, (M0 | PIN_INPUT_PULLUP)}, /* MMC1_DAT3 */ - {MMC1_SDCD, (M14 | PIN_INPUT) }, /* MMC1_SDCD */ - {MMC1_SDWP, (M14 | PIN_INPUT) }, /* MMC1_SDWP */ -}; - -/* WiFi - must be in the safe mode on boot */ -static const struct pad_conf_entry cl_som_am57x_padconf_wifi[] = { - {UART1_CTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART1_CTSN */ - {UART1_RTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART1_RTSN */ - {UART2_RXD, (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_RXD */ - {UART2_TXD, (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_TXD */ - {UART2_CTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_CTSN */ - {UART2_RTSN, (M15 | PIN_INPUT_PULLDOWN)}, /* UART2_RTSN */ -}; - -/* QSPI */ -static const struct pad_conf_entry cl_som_am57x_padconf_qspi[] = { - {GPMC_A13, (M1 | PIN_INPUT) }, /* GPMC_A13.QSPI1_RTCLK */ - {GPMC_A18, (M1 | PIN_INPUT) }, /* GPMC_A18.QSPI1_SCLK */ - {GPMC_A16, (M1 | PIN_INPUT) }, /* GPMC_A16.QSPI1_D0 */ - {GPMC_A17, (M1 | PIN_INPUT) }, /* GPMC_A17.QSPI1_D1 */ - {GPMC_CS2, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_CS2.QSPI1_CS0 */ -}; - -/* GPIO Expander I2C */ -static const struct pad_conf_entry cl_som_am57x_padconf_i2c_gpio[] = { - {MCASP1_AXR0, (M10 | PIN_INPUT)}, /* MCASP1_AXR0.I2C5_SDA */ - {MCASP1_AXR1, (M10 | PIN_INPUT)}, /* MCASP1_AXR1.I2C5_SCL */ -}; - -/* eMMC internal storage */ -static const struct pad_conf_entry cl_som_am57x_padconf_emmc[] = { - {GPMC_A19, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A19.MMC2_DAT4 */ - {GPMC_A20, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A20.MMC2_DAT5 */ - {GPMC_A21, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A21.MMC2_DAT6 */ - {GPMC_A22, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A22.MMC2_DAT7 */ - {GPMC_A23, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A23.MMC2_CLK */ - {GPMC_A24, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A24.MMC2_DAT0 */ - {GPMC_A25, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A25.MMC2_DAT1 */ - {GPMC_A26, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A26.MMC2_DAT2 */ - {GPMC_A27, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_A27.MMC2_DAT3 */ - {GPMC_CS1, (M1 | PIN_INPUT_PULLUP)}, /* GPMC_CS1.MMC2_CMD */ -}; - -/* usb1_drvvbus */ -static const struct pad_conf_entry cl_som_am57x_padconf_usb[] = { - /* USB1_DRVVBUS.USB1_DRVVBUS */ - {USB1_DRVVBUS, (M0 | PIN_OUTPUT_PULLDOWN | SLEWCONTROL) }, -}; - -/* Ethernet */ -static const struct pad_conf_entry cl_som_am57x_padconf_ethernet[] = { - /* MDIO bus */ - {VIN2A_D10, (M3 | PIN_OUTPUT_PULLUP) }, /* VIN2A_D10.MDIO_MCLK */ - {VIN2A_D11, (M3 | PIN_INPUT_PULLUP) }, /* VIN2A_D11.MDIO_D */ - /* EMAC Slave 1 at addr 0x1 - Default interface */ - {VIN2A_D12, (M3 | PIN_OUTPUT) }, /* VIN2A_D12.RGMII1_TXC */ - {VIN2A_D13, (M3 | PIN_OUTPUT) }, /* VIN2A_D13.RGMII1_TXCTL */ - {VIN2A_D14, (M3 | PIN_OUTPUT) }, /* VIN2A_D14.RGMII1_TXD3 */ - {VIN2A_D15, (M3 | PIN_OUTPUT) }, /* VIN2A_D15.RGMII1_TXD2 */ - {VIN2A_D16, (M3 | PIN_OUTPUT) }, /* VIN2A_D16.RGMII1_TXD1 */ - {VIN2A_D17, (M3 | PIN_OUTPUT) }, /* VIN2A_D17.RGMII1_TXD0 */ - {VIN2A_D18, (M3 | PIN_INPUT_PULLDOWN) }, /* VIN2A_D18.RGMII1_RXC */ - {VIN2A_D19, (M3 | PIN_INPUT_PULLDOWN) }, /* VIN2A_D19.RGMII1_RXCTL */ - {VIN2A_D20, (M3 | PIN_INPUT_PULLDOWN) }, /* VIN2A_D20.RGMII1_RXD3 */ - {VIN2A_D21, (M3 | PIN_INPUT_PULLDOWN) }, /* VIN2A_D21.RGMII1_RXD2 */ - {VIN2A_D22, (M3 | PIN_INPUT_PULLDOWN) }, /* VIN2A_D22.RGMII1_RXD1 */ - {VIN2A_D23, (M3 | PIN_INPUT_PULLDOWN) }, /* VIN2A_D23.RGMII1_RXD0 */ - /* Eth PHY1 reset GPIOs*/ - {VIN2A_CLK0, (M14 | PIN_OUTPUT_PULLDOWN)}, /* VIN2A_CLK0.GPIO3_28 */ -}; - -#define SET_MUX(mux_array) do_set_mux32((*ctrl)->control_padconf_core_base, \ - mux_array, ARRAY_SIZE(mux_array)) - -void set_muxconf_regs(void) -{ - SET_MUX(cl_som_am57x_padconf_console); - SET_MUX(cl_som_am57x_padconf_pmic); - SET_MUX(cl_som_am57x_padconf_green_led); - SET_MUX(cl_som_am57x_padconf_sd_card); - SET_MUX(cl_som_am57x_padconf_wifi); - SET_MUX(cl_som_am57x_padconf_qspi); - SET_MUX(cl_som_am57x_padconf_i2c_gpio); - SET_MUX(cl_som_am57x_padconf_emmc); - SET_MUX(cl_som_am57x_padconf_usb); - SET_MUX(cl_som_am57x_padconf_ethernet); -} diff --git a/board/compulab/cl-som-am57x/spl.c b/board/compulab/cl-som-am57x/spl.c deleted file mode 100644 index 0fb3d84a02..0000000000 --- a/board/compulab/cl-som-am57x/spl.c +++ /dev/null @@ -1,238 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * SPL data and initialization for CompuLab CL-SOM-AM57x board - * - * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/ - * - * Author: Uri Mashiach uri.mashiach@compulab.co.il - */ - -#include <asm/emif.h> -#include <asm/omap_common.h> -#include <asm/arch/sys_proto.h> - -static const struct dmm_lisa_map_regs cl_som_am57x_lisa_regs = { - .dmm_lisa_map_3 = 0x80740300, - .is_ma_present = 0x1 -}; - -void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs) -{ - /* Disable SDRAM controller EMIF2 for single core SOC */ - *dmm_lisa_regs = &cl_som_am57x_lisa_regs; - if (omap_revision() == DRA722_ES1_0) { - ((struct dmm_lisa_map_regs *) *dmm_lisa_regs)->dmm_lisa_map_3 = - 0x80640100; - } -} - -static const struct emif_regs cl_som_am57x_emif1_ddr3_532mhz_emif_regs = { - .sdram_config_init = 0x61852332, - .sdram_config = 0x61852332, - .sdram_config2 = 0x00000000, - .ref_ctrl = 0x000040f1, - .ref_ctrl_final = 0x00001040, - .sdram_tim1 = 0xeeef36f3, - .sdram_tim2 = 0x348f7fda, - .sdram_tim3 = 0x027f88a8, - .read_idle_ctrl = 0x00050000, - .zq_config = 0x1007190b, - .temp_alert_config = 0x00000000, - .emif_ddr_phy_ctlr_1_init = 0x0034400b, - .emif_ddr_phy_ctlr_1 = 0x0e34400b, - .emif_ddr_ext_phy_ctrl_1 = 0x04040100, - .emif_ddr_ext_phy_ctrl_2 = 0x00740074, - .emif_ddr_ext_phy_ctrl_3 = 0x00780078, - .emif_ddr_ext_phy_ctrl_4 = 0x007c007c, - .emif_ddr_ext_phy_ctrl_5 = 0x007b007b, - .emif_rd_wr_lvl_rmp_win = 0x00000000, - .emif_rd_wr_lvl_rmp_ctl = 0x80000000, - .emif_rd_wr_lvl_ctl = 0x00000000, - .emif_rd_wr_exec_thresh = 0x00000305 -}; - -/* Ext phy ctrl regs 1-35 */ -static const u32 cl_som_am57x_emif1_ddr3_ext_phy_ctrl_regs[] = { - 0x10040100, - 0x00740074, - 0x00780078, - 0x007c007c, - 0x007b007b, - 0x00800080, - 0x00360036, - 0x00340034, - 0x00360036, - 0x00350035, - 0x00350035, - - 0x01ff01ff, - 0x01ff01ff, - 0x01ff01ff, - 0x01ff01ff, - 0x01ff01ff, - - 0x00430043, - 0x003e003e, - 0x004a004a, - 0x00470047, - 0x00400040, - - 0x00000000, - 0x00600020, - 0x40011080, - 0x08102040, - - 0x00400040, - 0x00400040, - 0x00400040, - 0x00400040, - 0x00400040, - 0x0, - 0x0, - 0x0, - 0x0, - 0x0 -}; - -static const struct emif_regs cl_som_am57x_emif2_ddr3_532mhz_emif_regs = { - .sdram_config_init = 0x61852332, - .sdram_config = 0x61852332, - .sdram_config2 = 0x00000000, - .ref_ctrl = 0x000040f1, - .ref_ctrl_final = 0x00001040, - .sdram_tim1 = 0xeeef36f3, - .sdram_tim2 = 0x348f7fda, - .sdram_tim3 = 0x027f88a8, - .read_idle_ctrl = 0x00050000, - .zq_config = 0x1007190b, - .temp_alert_config = 0x00000000, - .emif_ddr_phy_ctlr_1_init = 0x0034400b, - .emif_ddr_phy_ctlr_1 = 0x0e34400b, - .emif_ddr_ext_phy_ctrl_1 = 0x04040100, - .emif_ddr_ext_phy_ctrl_2 = 0x00740074, - .emif_ddr_ext_phy_ctrl_3 = 0x00780078, - .emif_ddr_ext_phy_ctrl_4 = 0x007c007c, - .emif_ddr_ext_phy_ctrl_5 = 0x007b007b, - .emif_rd_wr_lvl_rmp_win = 0x00000000, - .emif_rd_wr_lvl_rmp_ctl = 0x80000000, - .emif_rd_wr_lvl_ctl = 0x00000000, - .emif_rd_wr_exec_thresh = 0x00000305 -}; - -static const u32 cl_som_am57x_emif2_ddr3_ext_phy_ctrl_regs[] = { - 0x10040100, - 0x00820082, - 0x008b008b, - 0x00800080, - 0x007e007e, - 0x00800080, - 0x00370037, - 0x00390039, - 0x00360036, - 0x00370037, - 0x00350035, - 0x01ff01ff, - 0x01ff01ff, - 0x01ff01ff, - 0x01ff01ff, - 0x01ff01ff, - 0x00540054, - 0x00540054, - 0x004e004e, - 0x004c004c, - 0x00400040, - - 0x00000000, - 0x00600020, - 0x40011080, - 0x08102040, - - 0x00400040, - 0x00400040, - 0x00400040, - 0x00400040, - 0x00400040, - 0x0, - 0x0, - 0x0, - 0x0, - 0x0 -}; - -static struct vcores_data cl_som_am57x_volts = { - .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, - .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, - .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, - .mpu.addr = TPS659038_REG_ADDR_SMPS12, - .mpu.pmic = &tps659038, - - .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, - .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, - .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, - .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, - .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, - .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, - .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, - .eve.addr = TPS659038_REG_ADDR_SMPS45, - .eve.pmic = &tps659038, - - .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, - .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, - .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, - .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, - .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, - .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, - .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, - .gpu.addr = TPS659038_REG_ADDR_SMPS6, - .gpu.pmic = &tps659038, - - .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, - .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, - .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, - .core.addr = TPS659038_REG_ADDR_SMPS7, - .core.pmic = &tps659038, - - .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, - .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, - .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, - .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, - .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, - .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, - .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, - .iva.addr = TPS659038_REG_ADDR_SMPS8, - .iva.pmic = &tps659038, -}; - -void hw_data_init(void) -{ - *prcm = &dra7xx_prcm; - *dplls_data = &dra7xx_dplls; - *omap_vcores = &cl_som_am57x_volts; - *ctrl = &dra7xx_ctrl; -} - -void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs) -{ - switch (emif_nr) { - case 1: - *regs = &cl_som_am57x_emif1_ddr3_532mhz_emif_regs; - break; - case 2: - *regs = &cl_som_am57x_emif2_ddr3_532mhz_emif_regs; - break; - } -} - -void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size) -{ - switch (emif_nr) { - case 1: - *regs = cl_som_am57x_emif1_ddr3_ext_phy_ctrl_regs; - *size = ARRAY_SIZE(cl_som_am57x_emif1_ddr3_ext_phy_ctrl_regs); - break; - case 2: - *regs = cl_som_am57x_emif2_ddr3_ext_phy_ctrl_regs; - *size = ARRAY_SIZE(cl_som_am57x_emif2_ddr3_ext_phy_ctrl_regs); - break; - } -} diff --git a/configs/cl-som-am57x_defconfig b/configs/cl-som-am57x_defconfig deleted file mode 100644 index fd8353ede5..0000000000 --- a/configs/cl-som-am57x_defconfig +++ /dev/null @@ -1,64 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_OMAP2PLUS=y -CONFIG_OMAP54XX=y -CONFIG_TARGET_CL_SOM_AM57X=y -CONFIG_SPL=y -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_NR_DRAM_BANKS=2 -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_VERSION_VARIABLE=y -# CONFIG_SPL_FS_EXT4 is not set -# CONFIG_SPL_NAND_SUPPORT is not set -CONFIG_SPL_SPI_LOAD=y -CONFIG_SYS_PROMPT="U-Boot# " -CONFIG_CMD_ASKENV=y -CONFIG_CMD_EEPROM=y -CONFIG_CMD_EEPROM_LAYOUT=y -CONFIG_EEPROM_LAYOUT_HELP_STRING="v2, v3" -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_SPI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_EXT4_WRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y -CONFIG_SCSI_AHCI=y -CONFIG_CMD_PCA953X=y -CONFIG_LED_STATUS=y -CONFIG_LED_STATUS_GPIO=y -CONFIG_LED_STATUS0=y -CONFIG_LED_STATUS_BIT=37 -CONFIG_LED_STATUS_STATE=2 -CONFIG_MMC_OMAP_HS=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_SPEED=48000000 -CONFIG_SPI_FLASH_ATMEL=y -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_GIGADEVICE=y -CONFIG_SPI_FLASH_MACRONIX=y -CONFIG_SPI_FLASH_SPANSION=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_SPI_FLASH_WINBOND=y -CONFIG_MII=y -CONFIG_DRIVER_TI_CPSW=y -CONFIG_CONS_INDEX=3 -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_TI_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -CONFIG_OMAP_USB_PHY=y -CONFIG_USB_HOST_ETHER=y -CONFIG_USB_ETHER_ASIX=y -CONFIG_USB_ETHER_MCS7830=y -CONFIG_USB_ETHER_SMSC95XX=y -CONFIG_FAT_WRITE=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/cl-som-am57x.h b/include/configs/cl-som-am57x.h deleted file mode 100644 index bf2bb44d48..0000000000 --- a/include/configs/cl-som-am57x.h +++ /dev/null @@ -1,148 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuration settings for CompuLab CL-SOM-AM57x board - * - * (C) Copyright 2016 CompuLab, Ltd. http://compulab.co.il/ - * - * Author: Dmitry Lifshitz lifshitz@compulab.co.il - */ - -#ifndef __CONFIG_CL_SOM_AM57X_H -#define __CONFIG_CL_SOM_AM57X_H - -#define CONSOLEDEV "ttyO2" -#define CONFIG_SYS_NS16550_COM3 UART3_BASE /* UART3 */ - -#define CONFIG_SYS_OMAP_ABE_SYSCK - -#define PARTS_DEFAULT - -#include <configs/ti_omap5_common.h> - -/* misc */ -#define CONFIG_REVISION_TAG - -/* PMIC I2C bus number */ -#define CONFIG_SYS_SPD_BUS_NUM 3 - -/* SPI Flash support */ -#define CONFIG_TI_SPI_MMAP - -/* SPI SPL defines */ -/* Offsets: 0K - SPL1, 64K - SPL2, 128K - SPL3, 192K - SPL4, 256K - U-Boot */ -#define CONFIG_SYS_SPI_U_BOOT_OFFS (256 * 1024) -#define CONFIG_SPL_SPI_SUPPORT - -/* SD/MMC RAW/FS boot */ -#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" -#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 - -/* Environment */ -#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB env size */ - -#define CONFIG_ENV_SECT_SIZE (64 * 1024) -#define CONFIG_ENV_OFFSET (768 * 1024) - -/* EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_I2C_EEPROM_BUS 3 - -#define CONFIG_ENV_EEPROM_IS_ON_I2C -#define CONFIG_SYS_EEPROM_SIZE 256 - -#ifndef CONFIG_SPL_BUILD -/* SATA */ -#define CONFIG_SCSI_AHCI_PLAT -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 -#define CONFIG_SYS_SCSI_MAX_LUN 1 -#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ - CONFIG_SYS_SCSI_MAX_LUN) -/* PCA9555 GPIO expander support */ -#define CONFIG_PCA953X -#define CONFIG_SYS_I2C_PCA953X_ADDR 0x20 -#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x20, 16} } - -#endif /* !CONFIG_SPL_BUILD */ - -/* USB xHCI HOST */ -#define CONFIG_USB_XHCI_OMAP - -#define CONFIG_OMAP_USB3PHY1_HOST - -/* USB Networking options */ - -/* CPSW Ethernet */ -#define CONFIG_BOOTP_DEFAULT -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_PHY_ATHEROS -#define CONFIG_SYS_RX_ETH_BUFFER 64 -#define PHY_ANEG_TIMEOUT 8000 - -#define CONFIG_BOOTP_DNS2 -#define CONFIG_NET_RETRY_COUNT 10 - -/* Default environment */ -#undef CONFIG_EXTRA_ENV_SETTINGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - DEFAULT_LINUX_BOOT_ENV \ - "autoload=no\0" \ - "baudrate=115200\0" \ - "console=ttyO2,115200n8\0" \ - "bootdelay=3\0" \ - "fdtfile=am57xx-sbc-am57x.dtb\0" \ - "kernel=zImage-cl-som-am57x\0" \ - "bootscr=bootscr.img\0" \ - "displaytype=hdmi\0" \ - "bootkernel=bootz ${loadaddr} - ${fdtaddr}\0" \ - "mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \ - "mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \ - "emmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \ - "emmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \ - "load_mmc=mmc dev ${mmcdev} && mmc rescan && " \ - "run mmcloadkernel && run mmcloadfdt\0" \ - "mmcroot=/dev/mmcblk1p2\0" \ - "mmcrootfstype=ext4 rw rootwait\0" \ - "mmcargs=setenv bootargs console=${console} root=${mmcroot} " \ - "rootfstype=${mmcrootfstype}\0" \ - "mmcbootscript=setenv mmcdev 0; mmc dev ${mmcdev} && mmc rescan && " \ - "load mmc ${mmcdev} ${loadaddr} ${bootscr} && " \ - "echo Running bootscript from MMC/SD Card ... && " \ - "source ${loadaddr}\0" \ - "mmcboot=setenv mmcdev 0 && run load_mmc && " \ - "run mmcargs && echo Booting from MMC/SD Card ... && " \ - "run bootkernel\0" \ - "emmcroot=/dev/mmcblk0p2\0" \ - "emmcrootfstype=ext4 rw rootwait\0" \ - "emmcargs=setenv bootargs console=${console} " \ - "root=${emmcroot} " \ - "rootfstype=${emmcrootfstype}\0" \ - "emmcbootscript=setenv mmcdev 1; mmc dev ${mmcdev} && mmc rescan && " \ - "load mmc ${mmcdev} ${loadaddr} ${bootscr} && " \ - "echo Running bootscript from eMMC ... && " \ - "source ${loadaddr}\0" \ - "emmcboot=setenv mmcdev 1 && run load_mmc && " \ - "run emmcargs && echo Booting from eMMC ... && " \ - "run bootkernel\0" \ - "sataroot=/dev/sda2\0" \ - "satarootfstype=ext4 rw rootwait\0" \ - "load_sata=load scsi 0 ${loadaddr} ${kernel} && " \ - "load scsi 0 ${fdtaddr} ${fdtfile}\0" \ - "sataargs=setenv bootargs console=${console} " \ - "root=${sataroot} " \ - "rootfstype=${satarootfstype}\0" \ - "satabootscript=load scsi 0 ${loadaddr} ${bootscr} && " \ - "echo Running bootscript from SATA ... && " \ - "source ${loadaddr}\0" \ - "sataboot=run load_sata && run sataargs && " \ - "echo Booting from SATA ... && " \ - "run bootkernel\0" - -#undef CONFIG_BOOTCOMMAND -#define CONFIG_BOOTCOMMAND \ - "run mmcbootscript || run mmcboot || " \ - "run satabootscript || run sataboot || " \ - "run emmcbootscript || run emmcboot" - - -#endif /* __CONFIG_CL_SOM_AM57X_H */