The TPS62517 PMIC driver has been partially converted to DM, so the legacy I2C access layer isn't needed anymore.

Signed-off-by: Hannes Schmelzer hannes.schmelzer@br-automation.com

---

board/BuR/brppt1/board.c | 5 ++--- board/BuR/brxre1/board.c | 2 +- board/BuR/common/bur_common.h | 2 +- board/BuR/common/common.c | 7 ++++--- configs/brppt1_mmc_defconfig | 1 - configs/brppt1_nand_defconfig | 1 - configs/brppt1_spi_defconfig | 1 - 7 files changed, 8 insertions(+), 11 deletions(-)

diff --git a/board/BuR/brppt1/board.c b/board/BuR/brppt1/board.c index d2e7c72..b8ab19c 100644 --- a/board/BuR/brppt1/board.c +++ b/board/BuR/brppt1/board.c @@ -106,9 +106,8 @@ void am33xx_spl_board_init(void)

/* setup I2C */ enable_i2c_pin_mux(); - i2c_set_bus_num(0); - i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); - pmicsetup(0); + + pmicsetup(0, 0);

/* peripheral reset */ rc = gpio_request(64 + 29, "GPMC_WAIT1"); diff --git a/board/BuR/brxre1/board.c b/board/BuR/brxre1/board.c index 41ed28b..82c53d5 100644 --- a/board/BuR/brxre1/board.c +++ b/board/BuR/brxre1/board.c @@ -132,7 +132,7 @@ void am33xx_spl_board_init(void) puts("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n"); }

- pmicsetup(0); + pmicsetup(0, 0); }

const struct dpll_params *get_dpll_ddr_params(void) diff --git a/board/BuR/common/bur_common.h b/board/BuR/common/bur_common.h index 5f2d0d0..f743194 100644 --- a/board/BuR/common/bur_common.h +++ b/board/BuR/common/bur_common.h @@ -15,7 +15,7 @@

int load_lcdtiming(struct am335x_lcdpanel *panel); void br_summaryscreen(void); -void pmicsetup(u32 mpupll); +void pmicsetup(u32 mpupll, unsigned int bus); void enable_uart0_pin_mux(void); void enable_i2c_pin_mux(void); void enable_board_pin_mux(void); diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c index f3eae5c..a1f7c44 100644 --- a/board/BuR/common/common.c +++ b/board/BuR/common/common.c @@ -269,13 +269,14 @@ int ft_board_setup(void *blob, bd_t *bd)

static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;

-void pmicsetup(u32 mpupll) +void pmicsetup(u32 mpupll, unsigned int bus) { int mpu_vdd; int usb_cur_lim;

- if (i2c_probe(TPS65217_CHIP_PM)) { - puts("PMIC (0x24) not found! skip further initalization.\n"); + if (power_tps65217_init(bus)) { + printf("WARN: cannot setup PMIC 0x24 @ bus #%d, not found!.\n", + bus); return; }

diff --git a/configs/brppt1_mmc_defconfig b/configs/brppt1_mmc_defconfig index 083b5f7..f2d8220 100644 --- a/configs/brppt1_mmc_defconfig +++ b/configs/brppt1_mmc_defconfig @@ -71,7 +71,6 @@ CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_BOOTCOUNT_LIMIT=y CONFIG_DM_GPIO=y CONFIG_DM_I2C=y -CONFIG_DM_I2C_COMPAT=y CONFIG_I2C_SET_DEFAULT_BUS_NUM=y CONFIG_MISC=y CONFIG_DM_MMC=y diff --git a/configs/brppt1_nand_defconfig b/configs/brppt1_nand_defconfig index 1cfd5fc..275727d 100644 --- a/configs/brppt1_nand_defconfig +++ b/configs/brppt1_nand_defconfig @@ -73,7 +73,6 @@ CONFIG_BLK=y CONFIG_BOOTCOUNT_LIMIT=y CONFIG_DM_GPIO=y CONFIG_DM_I2C=y -CONFIG_DM_I2C_COMPAT=y CONFIG_I2C_SET_DEFAULT_BUS_NUM=y CONFIG_MISC=y # CONFIG_MMC is not set diff --git a/configs/brppt1_spi_defconfig b/configs/brppt1_spi_defconfig index 3737396..668c4c2 100644 --- a/configs/brppt1_spi_defconfig +++ b/configs/brppt1_spi_defconfig @@ -76,7 +76,6 @@ CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_BOOTCOUNT_LIMIT=y CONFIG_DM_GPIO=y CONFIG_DM_I2C=y -CONFIG_DM_I2C_COMPAT=y CONFIG_I2C_SET_DEFAULT_BUS_NUM=y CONFIG_MISC=y CONFIG_DM_MMC=y