Signed-off-by: Andreas Bießmann andreas.devel@googlemail.com ---

arch/avr32/Kconfig | 4 - board/earthlcd/favr-32-ezkit/Kconfig | 15 -- board/earthlcd/favr-32-ezkit/MAINTAINERS | 6 - board/earthlcd/favr-32-ezkit/Makefile | 9 -- board/earthlcd/favr-32-ezkit/favr-32-ezkit.c | 81 ---------- board/earthlcd/favr-32-ezkit/flash.c | 216 --------------------------- configs/favr-32-ezkit_defconfig | 2 - include/configs/favr-32-ezkit.h | 181 ---------------------- 8 files changed, 514 deletions(-) delete mode 100644 board/earthlcd/favr-32-ezkit/Kconfig delete mode 100644 board/earthlcd/favr-32-ezkit/MAINTAINERS delete mode 100644 board/earthlcd/favr-32-ezkit/Makefile delete mode 100644 board/earthlcd/favr-32-ezkit/favr-32-ezkit.c delete mode 100644 board/earthlcd/favr-32-ezkit/flash.c delete mode 100644 configs/favr-32-ezkit_defconfig delete mode 100644 include/configs/favr-32-ezkit.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index e4b37bc..aa08d3e 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -22,9 +22,6 @@ config TARGET_ATSTK1004 config TARGET_ATSTK1006 bool "Support atstk1006"

-config TARGET_FAVR_32_EZKIT - bool "Support favr-32-ezkit" - config TARGET_GRASSHOPPER bool "Support grasshopper"

@@ -38,7 +35,6 @@ endchoice

source "board/atmel/atngw100mkii/Kconfig" source "board/atmel/atstk1000/Kconfig" -source "board/earthlcd/favr-32-ezkit/Kconfig" source "board/in-circuit/grasshopper/Kconfig" source "board/mimc/mimc200/Kconfig" source "board/miromico/hammerhead/Kconfig" diff --git a/board/earthlcd/favr-32-ezkit/Kconfig b/board/earthlcd/favr-32-ezkit/Kconfig deleted file mode 100644 index 50e29ec..0000000 --- a/board/earthlcd/favr-32-ezkit/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_FAVR_32_EZKIT - -config SYS_BOARD - default "favr-32-ezkit" - -config SYS_VENDOR - default "earthlcd" - -config SYS_SOC - default "at32ap700x" - -config SYS_CONFIG_NAME - default "favr-32-ezkit" - -endif diff --git a/board/earthlcd/favr-32-ezkit/MAINTAINERS b/board/earthlcd/favr-32-ezkit/MAINTAINERS deleted file mode 100644 index 89ba862..0000000 --- a/board/earthlcd/favr-32-ezkit/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -FAVR-32-EZKIT BOARD -#M: Hans-Christian Egtvedt hans-christian.egtvedt@atmel.com -S: Orphan (since 2014-06) -F: board/earthlcd/favr-32-ezkit/ -F: include/configs/favr-32-ezkit.h -F: configs/favr-32-ezkit_defconfig diff --git a/board/earthlcd/favr-32-ezkit/Makefile b/board/earthlcd/favr-32-ezkit/Makefile deleted file mode 100644 index f712ab9..0000000 --- a/board/earthlcd/favr-32-ezkit/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# Copyright (C) 2008 Atmel Corporation -# -# SPDX-License-Identifier: GPL-2.0+ - -obj-y := favr-32-ezkit.o flash.o diff --git a/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c b/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c deleted file mode 100644 index f9ac330..0000000 --- a/board/earthlcd/favr-32-ezkit/favr-32-ezkit.c +++ /dev/null @@ -1,81 +0,0 @@ -/* - * Copyright (C) 2008 Atmel Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <netdev.h> - -#include <asm/io.h> -#include <asm/sdram.h> -#include <asm/arch/clk.h> -#include <asm/arch/hmatrix.h> -#include <asm/arch/mmu.h> -#include <asm/arch/portmux.h> - -DECLARE_GLOBAL_DATA_PTR; - -struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = { - { - .virt_pgno = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT, - .nr_pages = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_NONE, - }, { - .virt_pgno = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT, - .nr_pages = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_WRBACK, - }, -}; - -static const struct sdram_config sdram_config = { - /* MT48LC4M32B2P-6 (16 MB) */ - .data_bits = SDRAM_DATA_32BIT, - .row_bits = 12, - .col_bits = 8, - .bank_bits = 2, - .cas = 3, - .twr = 2, - .trc = 7, - .trp = 2, - .trcd = 2, - .tras = 5, - .txsr = 5, - /* 15.6 us */ - .refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000, -}; - -int board_early_init_f(void) -{ - /* Enable SDRAM in the EBI mux */ - hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE)); - - portmux_enable_ebi(32, 23, 0, PORTMUX_DRIVE_HIGH); - - sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config); - - portmux_enable_usart3(PORTMUX_DRIVE_MIN); -#if defined(CONFIG_MACB) - portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH); -#endif -#if defined(CONFIG_MMC) - portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW); -#endif - - return 0; -} - -int board_early_init_r(void) -{ - gd->bd->bi_phy_id[0] = 0x01; - return 0; -} - -#if defined(CONFIG_MACB) && defined(CONFIG_CMD_NET) -int board_eth_init(bd_t *bi) -{ - return macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, - bi->bi_phy_id[0]); -} -#endif diff --git a/board/earthlcd/favr-32-ezkit/flash.c b/board/earthlcd/favr-32-ezkit/flash.c deleted file mode 100644 index e45c6f4..0000000 --- a/board/earthlcd/favr-32-ezkit/flash.c +++ /dev/null @@ -1,216 +0,0 @@ -/* - * Copyright (C) 2008 Atmel Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> - -#ifdef CONFIG_FAVR32_EZKIT_EXT_FLASH -#include <asm/arch/cacheflush.h> -#include <asm/io.h> -#include <asm/sections.h> - -DECLARE_GLOBAL_DATA_PTR; - -flash_info_t flash_info[1]; - -static void flash_identify(uint16_t *flash, flash_info_t *info) -{ - unsigned long flags; - - flags = disable_interrupts(); - - dcache_flush_unlocked(); - - writew(0xaa, flash + 0x555); - writew(0x55, flash + 0xaaa); - writew(0x90, flash + 0x555); - info->flash_id = readl(flash); - writew(0xff, flash); - - readw(flash); - - if (flags) - enable_interrupts(); -} - -unsigned long flash_init(void) -{ - unsigned long addr; - unsigned int i; - - flash_info[0].size = CONFIG_SYS_FLASH_SIZE; - flash_info[0].sector_count = 135; - - flash_identify(uncached((void *)CONFIG_SYS_FLASH_BASE), &flash_info[0]); - - for (i = 0, addr = 0; i < 8; i++, addr += 0x2000) - flash_info[0].start[i] = addr; - for (; i < flash_info[0].sector_count; i++, addr += 0x10000) - flash_info[0].start[i] = addr; - - return CONFIG_SYS_FLASH_SIZE; -} - -void flash_print_info(flash_info_t *info) -{ - printf("Flash: Vendor ID: 0x%02lx, Product ID: 0x%02lx\n", - info->flash_id >> 16, info->flash_id & 0xffff); - printf("Size: %ld MB in %d sectors\n", - info->size >> 10, info->sector_count); -} - -int flash_erase(flash_info_t *info, int s_first, int s_last) -{ - unsigned long flags; - unsigned long start_time; - uint16_t *fb, *sb; - unsigned int i; - int ret; - uint16_t status; - - if ((s_first < 0) || (s_first > s_last) - || (s_last >= info->sector_count)) { - puts("Error: first and/or last sector out of range\n"); - return ERR_INVAL; - } - - for (i = s_first; i < s_last; i++) - if (info->protect[i]) { - printf("Error: sector %d is protected\n", i); - return ERR_PROTECTED; - } - - fb = (uint16_t *)uncached(info->start[0]); - - dcache_flush_unlocked(); - - for (i = s_first; (i <= s_last) && !ctrlc(); i++) { - printf("Erasing sector %3d...", i); - - sb = (uint16_t *)uncached(info->start[i]); - - flags = disable_interrupts(); - - start_time = get_timer(0); - - /* Unlock sector */ - writew(0xaa, fb + 0x555); - writew(0x70, sb); - - /* Erase sector */ - writew(0xaa, fb + 0x555); - writew(0x55, fb + 0xaaa); - writew(0x80, fb + 0x555); - writew(0xaa, fb + 0x555); - writew(0x55, fb + 0xaaa); - writew(0x30, sb); - - /* Wait for completion */ - ret = ERR_OK; - do { - /* TODO: Timeout */ - status = readw(sb); - } while ((status != 0xffff) && !(status & 0x28)); - - writew(0xf0, fb); - - /* - * Make sure the command actually makes it to the bus - * before we re-enable interrupts. - */ - readw(fb); - - if (flags) - enable_interrupts(); - - if (status != 0xffff) { - printf("Flash erase error at address 0x%p: 0x%02x\n", - sb, status); - ret = ERR_PROG_ERROR; - break; - } - } - - if (ctrlc()) - printf("User interrupt!\n"); - - return ERR_OK; -} - -int write_buff(flash_info_t *info, uchar *src, - ulong addr, ulong count) -{ - unsigned long flags; - uint16_t *base, *p, *s, *end; - uint16_t word, status, status1; - int ret = ERR_OK; - - if (addr < info->start[0] - || (addr + count) > (info->start[0] + info->size) - || (addr + count) < addr) { - puts("Error: invalid address range\n"); - return ERR_INVAL; - } - - if (addr & 1 || count & 1 || (unsigned int)src & 1) { - puts("Error: misaligned source, destination or count\n"); - return ERR_ALIGN; - } - - base = (uint16_t *)uncached(info->start[0]); - end = (uint16_t *)uncached(addr + count); - - flags = disable_interrupts(); - - dcache_flush_unlocked(); - sync_write_buffer(); - - for (p = (uint16_t *)uncached(addr), s = (uint16_t *)src; - p < end && !ctrlc(); p++, s++) { - word = *s; - - writew(0xaa, base + 0x555); - writew(0x55, base + 0xaaa); - writew(0xa0, base + 0x555); - writew(word, p); - - sync_write_buffer(); - - /* Wait for completion */ - status1 = readw(p); - do { - /* TODO: Timeout */ - status = status1; - status1 = readw(p); - } while (((status ^ status1) & 0x40) /* toggled */ - && !(status1 & 0x28)); /* error bits */ - - /* - * We'll need to check once again for toggle bit - * because the toggle bit may stop toggling as I/O5 - * changes to "1" (ref at49bv642.pdf p9) - */ - status1 = readw(p); - status = readw(p); - if ((status ^ status1) & 0x40) { - printf("Flash write error at address 0x%p: " - "0x%02x != 0x%02x\n", - p, status,word); - ret = ERR_PROG_ERROR; - writew(0xf0, base); - readw(base); - break; - } - - writew(0xf0, base); - readw(base); - } - - if (flags) - enable_interrupts(); - - return ret; -} - -#endif /* CONFIG_FAVR32_EZKIT_EXT_FLASH */ diff --git a/configs/favr-32-ezkit_defconfig b/configs/favr-32-ezkit_defconfig deleted file mode 100644 index 941e028..0000000 --- a/configs/favr-32-ezkit_defconfig +++ /dev/null @@ -1,2 +0,0 @@ -CONFIG_AVR32=y -CONFIG_TARGET_FAVR_32_EZKIT=y diff --git a/include/configs/favr-32-ezkit.h b/include/configs/favr-32-ezkit.h deleted file mode 100644 index 75bff4c..0000000 --- a/include/configs/favr-32-ezkit.h +++ /dev/null @@ -1,181 +0,0 @@ -/* - * Copyright (C) 2008 Atmel Corporation - * - * Configuration settings for the Favr-32 EarthLCD LCD kit. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <asm/arch/hardware.h> - -#define CONFIG_AT32AP -#define CONFIG_AT32AP7000 -#define CONFIG_FAVR32_EZKIT - -#define CONFIG_FAVR32_EZKIT_EXT_FLASH - -/* - * Set up the PLL to run at 140 MHz, the CPU to run at the PLL - * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the - * PLL frequency. - * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz - */ -#define CONFIG_PLL -#define CONFIG_SYS_POWER_MANAGER -#define CONFIG_SYS_OSC0_HZ 20000000 -#define CONFIG_SYS_PLL0_DIV 1 -#define CONFIG_SYS_PLL0_MUL 7 -#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 -/* - * Set the CPU running at: - * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz - */ -#define CONFIG_SYS_CLKDIV_CPU 0 -/* - * Set the HSB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz - */ -#define CONFIG_SYS_CLKDIV_HSB 1 -/* - * Set the PBA running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz - */ -#define CONFIG_SYS_CLKDIV_PBA 2 -/* - * Set the PBB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz - */ -#define CONFIG_SYS_CLKDIV_PBB 1 - -/* Reserve VM regions for SDRAM and NOR flash */ -#define CONFIG_SYS_NR_VM_REGIONS 2 - -/* - * The PLLOPT register controls the PLL like this: - * icp = PLLOPT<2> - * ivco = PLLOPT<1:0> - * - * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). - */ -#define CONFIG_SYS_PLL0_OPT 0x04 - -#define CONFIG_USART_BASE ATMEL_BASE_USART3 -#define CONFIG_USART_ID 3 - -/* User serviceable stuff */ -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_STACKSIZE (2048) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTARGS \ - "root=/dev/mtdblock1 rootfstype=jffs fbmem=1800k" - -#define CONFIG_BOOTCOMMAND \ - "fsload; bootm $(fileaddr)" - -/* - * Only interrupt autoboot if <space> is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 1 -#define CONFIG_AUTOBOOT -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -/* - * After booting the board for the first time, new ethernet addresses - * should be generated and assigned to the environment variables - * "ethaddr" and "eth1addr". This is normally done during production. - */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MMC - -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_SETGETDCR -#undef CONFIG_CMD_SOURCE -#undef CONFIG_CMD_XIMG - -#define CONFIG_ATMEL_USART -#define CONFIG_MACB -#define CONFIG_PORTMUX_PIO -#define CONFIG_SYS_NR_PIOS 5 -#define CONFIG_SYS_HSDRAMC -#define CONFIG_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_GENERIC_MMC - -#define CONFIG_SYS_DCACHE_LINESZ 32 -#define CONFIG_SYS_ICACHE_LINESZ 32 - -#define CONFIG_NR_DRAM_BANKS 1 - -/* External flash on Favr-32 */ -#if 0 -#define CONFIG_SYS_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#endif - -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x800000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE -#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE -#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 65536 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) - -#define CONFIG_SYS_MALLOC_LEN (256*1024) - -/* Allow 4MB for the kernel run-time image */ -#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) -#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) - -/* Other configuration settings that shouldn't have to change all that often */ -#define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP - -#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x700000) -#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } - -#endif /* __CONFIG_H */

Signed-off-by: Andreas Bießmann andreas.devel@googlemail.com ---

arch/avr32/Kconfig | 4 - board/miromico/hammerhead/Kconfig | 15 ---- board/miromico/hammerhead/MAINTAINERS | 6 -- board/miromico/hammerhead/Makefile | 6 -- board/miromico/hammerhead/hammerhead.c | 91 ------------------- configs/hammerhead_defconfig | 2 - include/configs/hammerhead.h | 157 --------------------------------- 7 files changed, 281 deletions(-) delete mode 100644 board/miromico/hammerhead/Kconfig delete mode 100644 board/miromico/hammerhead/MAINTAINERS delete mode 100644 board/miromico/hammerhead/Makefile delete mode 100644 board/miromico/hammerhead/hammerhead.c delete mode 100644 configs/hammerhead_defconfig delete mode 100644 include/configs/hammerhead.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index aa08d3e..8cc6cea 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -28,15 +28,11 @@ config TARGET_GRASSHOPPER config TARGET_MIMC200 bool "Support mimc200"

-config TARGET_HAMMERHEAD - bool "Support hammerhead" - endchoice

source "board/atmel/atngw100mkii/Kconfig" source "board/atmel/atstk1000/Kconfig" source "board/in-circuit/grasshopper/Kconfig" source "board/mimc/mimc200/Kconfig" -source "board/miromico/hammerhead/Kconfig"

endmenu diff --git a/board/miromico/hammerhead/Kconfig b/board/miromico/hammerhead/Kconfig deleted file mode 100644 index 1f09ef7..0000000 --- a/board/miromico/hammerhead/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_HAMMERHEAD - -config SYS_BOARD - default "hammerhead" - -config SYS_VENDOR - default "miromico" - -config SYS_SOC - default "at32ap700x" - -config SYS_CONFIG_NAME - default "hammerhead" - -endif diff --git a/board/miromico/hammerhead/MAINTAINERS b/board/miromico/hammerhead/MAINTAINERS deleted file mode 100644 index a87ceee..0000000 --- a/board/miromico/hammerhead/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -HAMMERHEAD BOARD -M: Alex Raimondi alex.raimondi@miromico.ch -S: Maintained -F: board/miromico/hammerhead/ -F: include/configs/hammerhead.h -F: configs/hammerhead_defconfig diff --git a/board/miromico/hammerhead/Makefile b/board/miromico/hammerhead/Makefile deleted file mode 100644 index 638a9df..0000000 --- a/board/miromico/hammerhead/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# -# Copyright (C) 2008 Miromico AG -# -# SPDX-License-Identifier: GPL-2.0+ - -obj-y := hammerhead.o diff --git a/board/miromico/hammerhead/hammerhead.c b/board/miromico/hammerhead/hammerhead.c deleted file mode 100644 index a0c7d3b..0000000 --- a/board/miromico/hammerhead/hammerhead.c +++ /dev/null @@ -1,91 +0,0 @@ -/* - * Copyright (C) 2008 Miromico AG - * - * Mostly copied form atmel ATNGW100 sources - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <netdev.h> - -#include <asm/io.h> -#include <asm/sdram.h> -#include <asm/arch/clk.h> -#include <asm/arch/hmatrix.h> -#include <asm/arch/hardware.h> -#include <asm/arch/mmu.h> -#include <asm/arch/portmux.h> - -DECLARE_GLOBAL_DATA_PTR; - -struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = { - { - .virt_pgno = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT, - .nr_pages = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_NONE, - }, { - .virt_pgno = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT, - .nr_pages = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_WRBACK, - }, -}; - -static const struct sdram_config sdram_config = { - .data_bits = SDRAM_DATA_32BIT, - .row_bits = 13, - .col_bits = 9, - .bank_bits = 2, - .cas = 3, - .twr = 2, - .trc = 7, - .trp = 2, - .trcd = 2, - .tras = 5, - .txsr = 5, - /* 7.81 us */ - .refresh_period = (781 * (SDRAMC_BUS_HZ / 1000)) / 100000, -}; - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bis) -{ - return macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, - bis->bi_phy_id[0]); -} -#endif - -int board_early_init_f(void) -{ - /* Enable SDRAM in the EBI mux */ - hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE)); - - portmux_enable_ebi(32, 23, 0, PORTMUX_DRIVE_HIGH); - sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config); - - portmux_enable_usart1(PORTMUX_DRIVE_MIN); - -#if defined(CONFIG_MACB) - portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH); -#endif -#if defined(CONFIG_MMC) - portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW); -#endif - return 0; -} - -int board_early_init_r(void) -{ - gd->bd->bi_phy_id[0] = 0x01; - return 0; -} - -int board_postclk_init(void) -{ - /* Hammerhead boards uses GCLK3 as 25MHz output to ethernet PHY */ - gclk_enable_output(3, PORTMUX_DRIVE_LOW); - gclk_set_rate(3, GCLK_PARENT_OSC0, 25000000); - return 0; -} diff --git a/configs/hammerhead_defconfig b/configs/hammerhead_defconfig deleted file mode 100644 index 0d69cc6..0000000 --- a/configs/hammerhead_defconfig +++ /dev/null @@ -1,2 +0,0 @@ -CONFIG_AVR32=y -CONFIG_TARGET_HAMMERHEAD=y diff --git a/include/configs/hammerhead.h b/include/configs/hammerhead.h deleted file mode 100644 index 0bc42f1..0000000 --- a/include/configs/hammerhead.h +++ /dev/null @@ -1,157 +0,0 @@ -/* - * Copyright (C) 2008 Miromico AG - * - * Configuration settings for the Miromico Hammerhead AVR32 board - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_AT32AP -#define CONFIG_AT32AP7000 -#define CONFIG_HAMMERHEAD - -/* - * Set up the PLL to run at 125 MHz, the CPU to run at the PLL - * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency - * and the PBA bus to run at 1/4 the PLL frequency. - */ -#define CONFIG_PLL -#define CONFIG_SYS_POWER_MANAGER -#define CONFIG_SYS_OSC0_HZ 25000000 -#define CONFIG_SYS_PLL0_DIV 1 -#define CONFIG_SYS_PLL0_MUL 5 -#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 -#define CONFIG_SYS_CLKDIV_CPU 0 -#define CONFIG_SYS_CLKDIV_HSB 1 -#define CONFIG_SYS_CLKDIV_PBA 2 -#define CONFIG_SYS_CLKDIV_PBB 1 - -/* Reserve VM regions for SDRAM and NOR flash */ -#define CONFIG_SYS_NR_VM_REGIONS 2 - -/* - * The PLLOPT register controls the PLL like this: - * icp = PLLOPT<2> - * ivco = PLLOPT<1:0> - * - * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). - */ -#define CONFIG_SYS_PLL0_OPT 0x04 - -#define CONFIG_USART_BASE ATMEL_BASE_USART1 -#define CONFIG_USART_ID 1 - -#define CONFIG_HOSTNAME hammerhead - -/* User serviceable stuff */ -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_STACKSIZE (2048) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTARGS \ - "console=ttyS0 root=mtd1 rootfstype=jffs2" -#define CONFIG_BOOTCOMMAND \ - "fsload; bootm" - -/* - * Only interrupt autoboot if <space> is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 1 -#define CONFIG_AUTOBOOT -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -/* - * After booting the board for the first time, new ethernet address - * should be generated and assigned to the environment variables - * "ethaddr". This is normally done during production. - */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -/* - * BOOTP/DHCP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MMC -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_SETGETDCR - -#define CONFIG_ATMEL_USART -#define CONFIG_MACB -#define CONFIG_PORTMUX_PIO -#define CONFIG_SYS_NR_PIOS 5 -#define CONFIG_SYS_HSDRAMC -#define CONFIG_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_GENERIC_MMC - -#define CONFIG_SYS_DCACHE_LINESZ 32 -#define CONFIG_SYS_ICACHE_LINESZ 32 - -#define CONFIG_NR_DRAM_BANKS 1 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x800000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_SYS_INTRAM_BASE 0x24000000 -#define CONFIG_SYS_INTRAM_SIZE 0x8000 - -#define CONFIG_SYS_SDRAM_BASE 0x10000000 - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 65536 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) - -#define CONFIG_SYS_MALLOC_LEN (256*1024) - - -/* Allow 4MB for the kernel run-time image */ -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x00400000) -#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) - -/* Other configuration settings that shouldn't have to change all that often */ -#define CONFIG_SYS_PROMPT "Hammerhead> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP - -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x1f00000) - -#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } - -#endif /* __CONFIG_H */

Signed-off-by: Andreas Bießmann andreas.devel@googlemail.com ---

arch/avr32/Kconfig | 4 - board/mimc/mimc200/Kconfig | 15 ---- board/mimc/mimc200/MAINTAINERS | 6 -- board/mimc/mimc200/Makefile | 6 -- board/mimc/mimc200/mimc200.c | 197 ----------------------------------------- configs/mimc200_defconfig | 2 - include/configs/mimc200.h | 177 ------------------------------------ 7 files changed, 407 deletions(-) delete mode 100644 board/mimc/mimc200/Kconfig delete mode 100644 board/mimc/mimc200/MAINTAINERS delete mode 100644 board/mimc/mimc200/Makefile delete mode 100644 board/mimc/mimc200/mimc200.c delete mode 100644 configs/mimc200_defconfig delete mode 100644 include/configs/mimc200.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index 8cc6cea..c5c06ba 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -25,14 +25,10 @@ config TARGET_ATSTK1006 config TARGET_GRASSHOPPER bool "Support grasshopper"

-config TARGET_MIMC200 - bool "Support mimc200" - endchoice

source "board/atmel/atngw100mkii/Kconfig" source "board/atmel/atstk1000/Kconfig" source "board/in-circuit/grasshopper/Kconfig" -source "board/mimc/mimc200/Kconfig"

endmenu diff --git a/board/mimc/mimc200/Kconfig b/board/mimc/mimc200/Kconfig deleted file mode 100644 index 18736d7..0000000 --- a/board/mimc/mimc200/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_MIMC200 - -config SYS_BOARD - default "mimc200" - -config SYS_VENDOR - default "mimc" - -config SYS_SOC - default "at32ap700x" - -config SYS_CONFIG_NAME - default "mimc200" - -endif diff --git a/board/mimc/mimc200/MAINTAINERS b/board/mimc/mimc200/MAINTAINERS deleted file mode 100644 index 6cb51dd..0000000 --- a/board/mimc/mimc200/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MIMC200 BOARD -M: Mark Jackson mpfj@mimc.co.uk -S: Maintained -F: board/mimc/mimc200/ -F: include/configs/mimc200.h -F: configs/mimc200_defconfig diff --git a/board/mimc/mimc200/Makefile b/board/mimc/mimc200/Makefile deleted file mode 100644 index 5c30c0d..0000000 --- a/board/mimc/mimc200/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# -# Copyright (C) 2005-2006 Atmel Corporation -# -# SPDX-License-Identifier: GPL-2.0+ - -obj-y := mimc200.o diff --git a/board/mimc/mimc200/mimc200.c b/board/mimc/mimc200/mimc200.c deleted file mode 100644 index f078295..0000000 --- a/board/mimc/mimc200/mimc200.c +++ /dev/null @@ -1,197 +0,0 @@ -/* - * Copyright (C) 2006 Atmel Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <netdev.h> - -#include <asm/io.h> -#include <asm/sdram.h> -#include <asm/arch/clk.h> -#include <asm/arch/gpio.h> -#include <asm/arch/hmatrix.h> -#include <asm/arch/mmu.h> -#include <asm/arch/portmux.h> -#include <atmel_lcdc.h> -#include <lcd.h> - -#include "../../../arch/avr32/cpu/hsmc3.h" - -struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = { - { - .virt_pgno = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT, - .nr_pages = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_NONE, - }, { - .virt_pgno = EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT, - .nr_pages = EBI_SRAM_CS2_SIZE >> MMU_PAGE_SHIFT, - .phys = (EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_NONE, - }, { - .virt_pgno = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT, - .nr_pages = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_WRBACK, - }, -}; - -#if defined(CONFIG_LCD) -/* 480x272x16 @ 72 Hz */ -vidinfo_t panel_info = { - .vl_col = 480, /* Number of columns */ - .vl_row = 272, /* Number of rows */ - .vl_clk = 5000000, /* pixel clock in ps */ - .vl_sync = ATMEL_LCDC_INVCLK_INVERTED | - ATMEL_LCDC_INVLINE_INVERTED | - ATMEL_LCDC_INVFRAME_INVERTED, - .vl_bpix = LCD_COLOR16, /* Bits per pixel, BPP = 2^n */ - .vl_tft = 1, /* 0 = passive, 1 = TFT */ - .vl_hsync_len = 42, /* Length of horizontal sync */ - .vl_left_margin = 1, /* Time from sync to picture */ - .vl_right_margin = 1, /* Time from picture to sync */ - .vl_vsync_len = 1, /* Length of vertical sync */ - .vl_upper_margin = 12, /* Time from sync to picture */ - .vl_lower_margin = 1, /* Time from picture to sync */ - .mmio = LCDC_BASE, /* Memory mapped registers */ -}; - -void lcd_enable(void) -{ -} - -void lcd_disable(void) -{ -} -#endif - -DECLARE_GLOBAL_DATA_PTR; - -static const struct sdram_config sdram_config = { - .data_bits = SDRAM_DATA_16BIT, - .row_bits = 13, - .col_bits = 9, - .bank_bits = 2, - .cas = 3, - .twr = 2, - .trc = 6, - .trp = 2, - .trcd = 2, - .tras = 6, - .txsr = 6, - /* 15.6 us */ - .refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000, -}; - -int board_early_init_f(void) -{ - /* Enable SDRAM in the EBI mux */ - hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE)); - - /* Enable 26 address bits and NCS2 */ - portmux_enable_ebi(16, 26, PORTMUX_EBI_CS(2), PORTMUX_DRIVE_HIGH); - sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config); - - portmux_enable_usart1(PORTMUX_DRIVE_MIN); - - /* de-assert "force sys reset" pin */ - portmux_select_gpio(PORTMUX_PORT_D, 1 << 15, - PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH); - - /* init custom i/o */ - /* cpu type inputs */ - portmux_select_gpio(PORTMUX_PORT_E, (1 << 19) | (1 << 20) | (1 << 23), - PORTMUX_DIR_INPUT); - /* main board type inputs */ - portmux_select_gpio(PORTMUX_PORT_B, (1 << 19) | (1 << 29), - PORTMUX_DIR_INPUT); - /* DEBUG input (use weak pullup) */ - portmux_select_gpio(PORTMUX_PORT_E, 1 << 21, - PORTMUX_DIR_INPUT | PORTMUX_PULL_UP); - - /* are we suppressing the console ? */ - if (gpio_get_value(GPIO_PIN_PE(21)) == 1) - gd->flags |= (GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE); - - /* reset phys */ - portmux_select_gpio(PORTMUX_PORT_E, 1 << 24, PORTMUX_DIR_INPUT); - portmux_select_gpio(PORTMUX_PORT_C, 1 << 18, - PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH); - - udelay(5000); - - /* release phys reset */ - gpio_set_value(GPIO_PIN_PC(18), 0); /* PHY RESET (Release) */ - - /* setup Data Flash chip select (NCS2) */ - hsmc3_writel(MODE2, 0x20121003); - hsmc3_writel(CYCLE2, 0x000a0009); - hsmc3_writel(PULSE2, 0x0a060806); - hsmc3_writel(SETUP2, 0x00030102); - - /* setup FRAM chip select (NCS3) */ - hsmc3_writel(MODE3, 0x10120001); - hsmc3_writel(CYCLE3, 0x001e001d); - hsmc3_writel(PULSE3, 0x08040704); - hsmc3_writel(SETUP3, 0x02050204); - -#if defined(CONFIG_MACB) - /* init macb0 pins */ - portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH); - portmux_enable_macb1(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH); -#endif - -#if defined(CONFIG_MMC) - portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW); -#endif - -#if defined(CONFIG_LCD) - portmux_enable_lcdc(1); -#endif - - return 0; -} - -int board_early_init_r(void) -{ - gd->bd->bi_phy_id[0] = 0x01; - gd->bd->bi_phy_id[1] = 0x03; - return 0; -} - -int board_postclk_init(void) -{ - /* Use GCLK0 as 10MHz output */ - gclk_enable_output(0, PORTMUX_DRIVE_LOW); - gclk_set_rate(0, GCLK_PARENT_OSC0, 10000000); - return 0; -} - -/* SPI chip select control */ -#ifdef CONFIG_ATMEL_SPI -#include <spi.h> - -int spi_cs_is_valid(unsigned int bus, unsigned int cs) -{ - return (bus == 0) && (cs == 0); -} - -void spi_cs_activate(struct spi_slave *slave) -{ -} - -void spi_cs_deactivate(struct spi_slave *slave) -{ -} -#endif /* CONFIG_ATMEL_SPI */ - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bi) -{ - macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]); - macb_eth_initialize(1, (void *)ATMEL_BASE_MACB1, bi->bi_phy_id[1]); - - return 0; -} -#endif diff --git a/configs/mimc200_defconfig b/configs/mimc200_defconfig deleted file mode 100644 index f6edbc7..0000000 --- a/configs/mimc200_defconfig +++ /dev/null @@ -1,2 +0,0 @@ -CONFIG_AVR32=y -CONFIG_TARGET_MIMC200=y diff --git a/include/configs/mimc200.h b/include/configs/mimc200.h deleted file mode 100644 index 2fd3add..0000000 --- a/include/configs/mimc200.h +++ /dev/null @@ -1,177 +0,0 @@ -/* - * Copyright (C) 2006 Atmel Corporation - * - * Configuration settings for the AVR32 Network Gateway - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <asm/arch/hardware.h> - -#define CONFIG_AT32AP -#define CONFIG_AT32AP7000 -#define CONFIG_MIMC200 - -#define CONFIG_MIMC200_EXT_FLASH - -/* - * Set up the PLL to run at 140 MHz, the CPU to run at the PLL - * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency - * and the PBA bus to run at 1/4 the PLL frequency. - */ -#define CONFIG_PLL -#define CONFIG_SYS_POWER_MANAGER -#define CONFIG_SYS_OSC0_HZ 10000000 -#define CONFIG_SYS_PLL0_DIV 1 -#define CONFIG_SYS_PLL0_MUL 15 -#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 -#define CONFIG_SYS_CLKDIV_CPU 0 -#define CONFIG_SYS_CLKDIV_HSB 1 -#define CONFIG_SYS_CLKDIV_PBA 2 -#define CONFIG_SYS_CLKDIV_PBB 1 - -/* Reserve VM regions for SDRAM, NOR flash and FRAM */ -#define CONFIG_SYS_NR_VM_REGIONS 3 - -/* - * The PLLOPT register controls the PLL like this: - * icp = PLLOPT<2> - * ivco = PLLOPT<1:0> - * - * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). - */ -#define CONFIG_SYS_PLL0_OPT 0x04 - -#define CONFIG_USART_BASE ATMEL_BASE_USART1 -#define CONFIG_USART_ID 1 - -#define CONFIG_MIMC200_DBGLINK 1 - -/* User serviceable stuff */ -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_STACKSIZE (2048) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTARGS \ - "root=/dev/mtdblock1 rootfstype=jffs2 fbmem=512k console=ttyS1" -#define CONFIG_BOOTCOMMAND \ - "fsload boot/uImage; bootm" - -#define CONFIG_SILENT_CONSOLE /* enable silent startup */ -#define CONFIG_DISABLE_CONSOLE /* disable console */ -#define CONFIG_SYS_DEVICE_NULLDEV /* include nulldev device */ - -#define CONFIG_LCD 1 - -/* - * Only interrupt autoboot if <space> is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 0 -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_AUTOBOOT - -/* - * After booting the board for the first time, new ethernet addresses - * should be generated and assigned to the environment variables - * "ethaddr" and "eth1addr". This is normally done during production. - */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -/* - * BOOTP/DHCP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MMC -#define CONFIG_CMD_NET - -#define CONFIG_ATMEL_USART -#define CONFIG_MACB -#define CONFIG_PORTMUX_PIO -#define CONFIG_SYS_NR_PIOS 5 -#define CONFIG_SYS_HSDRAMC -#define CONFIG_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_GENERIC_MMC - -#if defined(CONFIG_LCD) -#define CONFIG_CMD_BMP -#define CONFIG_ATMEL_LCD 1 -#define LCD_BPP LCD_COLOR16 -#define CONFIG_BMP_16BPP 1 -#define CONFIG_FB_ADDR 0x10600000 -#define CONFIG_WHITE_ON_BLACK 1 -#define CONFIG_VIDEO_BMP_GZIP 1 -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE 262144 -#define CONFIG_ATMEL_LCD_BGR555 1 -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -#define CONFIG_SPLASH_SCREEN 1 -#endif - -#define CONFIG_SYS_DCACHE_LINESZ 32 -#define CONFIG_SYS_ICACHE_LINESZ 32 - -#define CONFIG_NR_DRAM_BANKS 1 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x800000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE -#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE -#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE - -#define CONFIG_SYS_FRAM_BASE 0x08000000 -#define CONFIG_SYS_FRAM_SIZE 0x20000 - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 65536 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) - -#define CONFIG_SYS_MALLOC_LEN (1024*1024) - -/* Allow 4MB for the kernel run-time image */ -#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) -#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) - -/* Other configuration settings that shouldn't have to change all that often */ -#define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP - -#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x1f00000) - -#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } - -#endif /* __CONFIG_H */

Signed-off-by: Andreas Bießmann andreas.devel@googlemail.com ---

arch/avr32/Kconfig | 9 -- board/atmel/atstk1000/Kconfig | 48 ---------- board/atmel/atstk1000/MAINTAINERS | 6 -- board/atmel/atstk1000/atstk1000.c | 23 +---- configs/atstk1003_defconfig | 2 - configs/atstk1004_defconfig | 2 - configs/atstk1006_defconfig | 2 - include/configs/atstk1003.h | 161 ---------------------------------- include/configs/atstk1004.h | 161 ---------------------------------- include/configs/atstk1006.h | 178 -------------------------------------- 10 files changed, 1 insertion(+), 591 deletions(-) delete mode 100644 configs/atstk1003_defconfig delete mode 100644 configs/atstk1004_defconfig delete mode 100644 configs/atstk1006_defconfig delete mode 100644 include/configs/atstk1003.h delete mode 100644 include/configs/atstk1004.h delete mode 100644 include/configs/atstk1006.h

diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index c5c06ba..2228dc1 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -13,15 +13,6 @@ config TARGET_ATNGW100MKII config TARGET_ATSTK1002 bool "Support atstk1002"

-config TARGET_ATSTK1003 - bool "Support atstk1003" - -config TARGET_ATSTK1004 - bool "Support atstk1004" - -config TARGET_ATSTK1006 - bool "Support atstk1006" - config TARGET_GRASSHOPPER bool "Support grasshopper"

diff --git a/board/atmel/atstk1000/Kconfig b/board/atmel/atstk1000/Kconfig index 6d41514..b4fa9a2 100644 --- a/board/atmel/atstk1000/Kconfig +++ b/board/atmel/atstk1000/Kconfig @@ -13,51 +13,3 @@ config SYS_CONFIG_NAME default "atstk1002"

endif - -if TARGET_ATSTK1003 - -config SYS_BOARD - default "atstk1000" - -config SYS_VENDOR - default "atmel" - -config SYS_SOC - default "at32ap700x" - -config SYS_CONFIG_NAME - default "atstk1003" - -endif - -if TARGET_ATSTK1004 - -config SYS_BOARD - default "atstk1000" - -config SYS_VENDOR - default "atmel" - -config SYS_SOC - default "at32ap700x" - -config SYS_CONFIG_NAME - default "atstk1004" - -endif - -if TARGET_ATSTK1006 - -config SYS_BOARD - default "atstk1000" - -config SYS_VENDOR - default "atmel" - -config SYS_SOC - default "at32ap700x" - -config SYS_CONFIG_NAME - default "atstk1006" - -endif diff --git a/board/atmel/atstk1000/MAINTAINERS b/board/atmel/atstk1000/MAINTAINERS index 378e1b3..6143846 100644 --- a/board/atmel/atstk1000/MAINTAINERS +++ b/board/atmel/atstk1000/MAINTAINERS @@ -4,9 +4,3 @@ S: Orphan (since 2014-06) F: board/atmel/atstk1000/ F: include/configs/atstk1002.h F: configs/atstk1002_defconfig -F: include/configs/atstk1003.h -F: configs/atstk1003_defconfig -F: include/configs/atstk1004.h -F: configs/atstk1004_defconfig -F: include/configs/atstk1006.h -F: configs/atstk1006_defconfig diff --git a/board/atmel/atstk1000/atstk1000.c b/board/atmel/atstk1000/atstk1000.c index fd4363b..679b674 100644 --- a/board/atmel/atstk1000/atstk1000.c +++ b/board/atmel/atstk1000/atstk1000.c @@ -30,32 +30,12 @@ struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = { };

static const struct sdram_config sdram_config = { -#if defined(CONFIG_ATSTK1006) - /* Dual MT48LC16M16A2-7E (64 MB) on daughterboard */ .data_bits = SDRAM_DATA_32BIT, - .row_bits = 13, - .col_bits = 9, - .bank_bits = 2, - .cas = 2, - .twr = 2, - .trc = 7, - .trp = 2, - .trcd = 2, - .tras = 4, - .txsr = 7, - /* 7.81 us */ - .refresh_period = (781 * (SDRAMC_BUS_HZ / 1000)) / 100000, -#else - /* MT48LC2M32B2P-5 (8 MB) on motherboard */ -#ifdef CONFIG_ATSTK1004 - .data_bits = SDRAM_DATA_16BIT, -#else - .data_bits = SDRAM_DATA_32BIT, -#endif #ifdef CONFIG_ATSTK1000_16MB_SDRAM /* MT48LC4M32B2P-6 (16 MB) on mod'ed motherboard */ .row_bits = 12, #else + /* MT48LC2M32B2P-5 (8 MB) on motherboard */ .row_bits = 11, #endif .col_bits = 8, @@ -69,7 +49,6 @@ static const struct sdram_config sdram_config = { .txsr = 5, /* 15.6 us */ .refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000, -#endif };

int board_early_init_f(void) diff --git a/configs/atstk1003_defconfig b/configs/atstk1003_defconfig deleted file mode 100644 index b704532..0000000 --- a/configs/atstk1003_defconfig +++ /dev/null @@ -1,2 +0,0 @@ -CONFIG_AVR32=y -CONFIG_TARGET_ATSTK1003=y diff --git a/configs/atstk1004_defconfig b/configs/atstk1004_defconfig deleted file mode 100644 index 7650254..0000000 --- a/configs/atstk1004_defconfig +++ /dev/null @@ -1,2 +0,0 @@ -CONFIG_AVR32=y -CONFIG_TARGET_ATSTK1004=y diff --git a/configs/atstk1006_defconfig b/configs/atstk1006_defconfig deleted file mode 100644 index 54beb0b..0000000 --- a/configs/atstk1006_defconfig +++ /dev/null @@ -1,2 +0,0 @@ -CONFIG_AVR32=y -CONFIG_TARGET_ATSTK1006=y diff --git a/include/configs/atstk1003.h b/include/configs/atstk1003.h deleted file mode 100644 index 63704b1..0000000 --- a/include/configs/atstk1003.h +++ /dev/null @@ -1,161 +0,0 @@ -/* - * Copyright (C) 2007 Atmel Corporation - * - * Configuration settings for the ATSTK1003 CPU daughterboard - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <asm/arch/hardware.h> - -#define CONFIG_AT32AP -#define CONFIG_AT32AP7001 -#define CONFIG_ATSTK1003 -#define CONFIG_ATSTK1000 - -/* - * Set up the PLL to run at 140 MHz, the CPU to run at the PLL - * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the - * PLL frequency. - * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz - */ -#define CONFIG_PLL -#define CONFIG_SYS_POWER_MANAGER -#define CONFIG_SYS_OSC0_HZ 20000000 -#define CONFIG_SYS_PLL0_DIV 1 -#define CONFIG_SYS_PLL0_MUL 7 -#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 -/* - * Set the CPU running at: - * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz - */ -#define CONFIG_SYS_CLKDIV_CPU 0 -/* - * Set the HSB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz - */ -#define CONFIG_SYS_CLKDIV_HSB 1 -/* - * Set the PBA running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz - */ -#define CONFIG_SYS_CLKDIV_PBA 2 -/* - * Set the PBB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz - */ -#define CONFIG_SYS_CLKDIV_PBB 1 - -/* Reserve VM regions for SDRAM and NOR flash */ -#define CONFIG_SYS_NR_VM_REGIONS 2 - -/* - * The PLLOPT register controls the PLL like this: - * icp = PLLOPT<2> - * ivco = PLLOPT<1:0> - * - * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). - */ -#define CONFIG_SYS_PLL0_OPT 0x04 - -#define CONFIG_USART_BASE ATMEL_BASE_USART1 -#define CONFIG_USART_ID 1 - -/* User serviceable stuff */ -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_STACKSIZE (2048) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTARGS \ - "console=ttyS0 root=/dev/mmcblk0p1 rootwait" - -#define CONFIG_BOOTCOMMAND \ - "mmc rescan; ext2load mmc 0:1 0x10400000 /boot/uImage; bootm" - -/* - * Only interrupt autoboot if <space> is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 1 -#define CONFIG_AUTOBOOT -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MMC - -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_SETGETDCR -#undef CONFIG_CMD_XIMG - -#define CONFIG_ATMEL_USART -#define CONFIG_PORTMUX_PIO -#define CONFIG_SYS_HSDRAMC -#define CONFIG_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_GENERIC_MMC - -#define CONFIG_SYS_DCACHE_LINESZ 32 -#define CONFIG_SYS_ICACHE_LINESZ 32 - -#define CONFIG_NR_DRAM_BANKS 1 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x800000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE -#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE -#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 65536 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) - -#define CONFIG_SYS_MALLOC_LEN (256*1024) - -/* Allow 4MB for the kernel run-time image */ -#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) -#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) - -/* Other configuration settings that shouldn't have to change all that often */ -#define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP - -#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x700000) -#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } - -#endif /* __CONFIG_H */ diff --git a/include/configs/atstk1004.h b/include/configs/atstk1004.h deleted file mode 100644 index 331a60d..0000000 --- a/include/configs/atstk1004.h +++ /dev/null @@ -1,161 +0,0 @@ -/* - * Copyright (C) 2007 Atmel Corporation - * - * Configuration settings for the ATSTK1003 CPU daughterboard - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <asm/arch/hardware.h> - -#define CONFIG_AT32AP -#define CONFIG_AT32AP7002 -#define CONFIG_ATSTK1004 -#define CONFIG_ATSTK1000 - -/* - * Set up the PLL to run at 140 MHz, the CPU to run at the PLL - * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the - * PLL frequency. - * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz - */ -#define CONFIG_PLL -#define CONFIG_SYS_POWER_MANAGER -#define CONFIG_SYS_OSC0_HZ 20000000 -#define CONFIG_SYS_PLL0_DIV 1 -#define CONFIG_SYS_PLL0_MUL 7 -#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 -/* - * Set the CPU running at: - * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz - */ -#define CONFIG_SYS_CLKDIV_CPU 0 -/* - * Set the HSB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz - */ -#define CONFIG_SYS_CLKDIV_HSB 1 -/* - * Set the PBA running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz - */ -#define CONFIG_SYS_CLKDIV_PBA 2 -/* - * Set the PBB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz - */ -#define CONFIG_SYS_CLKDIV_PBB 1 - -/* Reserve VM regions for SDRAM and NOR flash */ -#define CONFIG_SYS_NR_VM_REGIONS 2 - -/* - * The PLLOPT register controls the PLL like this: - * icp = PLLOPT<2> - * ivco = PLLOPT<1:0> - * - * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). - */ -#define CONFIG_SYS_PLL0_OPT 0x04 - -#define CONFIG_USART_BASE ATMEL_BASE_USART1 -#define CONFIG_USART_ID 1 - -/* User serviceable stuff */ -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_STACKSIZE (2048) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTARGS \ - "console=ttyS0 root=/dev/mmcblk0p1 rootwait" - -#define CONFIG_BOOTCOMMAND \ - "mmc rescan; ext2load mmc 0:1 0x10200000 /boot/uImage; bootm" - -/* - * Only interrupt autoboot if <space> is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 1 -#define CONFIG_AUTOBOOT -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MMC - -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_SETGETDCR -#undef CONFIG_CMD_XIMG - -#define CONFIG_ATMEL_USART -#define CONFIG_PORTMUX_PIO -#define CONFIG_SYS_HSDRAMC -#define CONFIG_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_GENERIC_MMC - -#define CONFIG_SYS_DCACHE_LINESZ 32 -#define CONFIG_SYS_ICACHE_LINESZ 32 - -#define CONFIG_NR_DRAM_BANKS 1 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x800000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE -#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE -#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 65536 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) - -#define CONFIG_SYS_MALLOC_LEN (256*1024) - -/* Allow 2MB for the kernel run-time image */ -#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00200000) -#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) - -/* Other configuration settings that shouldn't have to change all that often */ -#define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP - -#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x700000) -#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } - -#endif /* __CONFIG_H */ diff --git a/include/configs/atstk1006.h b/include/configs/atstk1006.h deleted file mode 100644 index 25090a6..0000000 --- a/include/configs/atstk1006.h +++ /dev/null @@ -1,178 +0,0 @@ -/* - * Copyright (C) 2005-2006 Atmel Corporation - * - * Configuration settings for the ATSTK1002 CPU daughterboard - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <asm/arch/hardware.h> - -#define CONFIG_AT32AP -#define CONFIG_AT32AP7000 -#define CONFIG_ATSTK1006 -#define CONFIG_ATSTK1000 - - -/* - * Set up the PLL to run at 140 MHz, the CPU to run at the PLL - * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the - * PLL frequency. - * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz - */ -#define CONFIG_PLL -#define CONFIG_SYS_POWER_MANAGER -#define CONFIG_SYS_OSC0_HZ 20000000 -#define CONFIG_SYS_PLL0_DIV 1 -#define CONFIG_SYS_PLL0_MUL 7 -#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 -/* - * Set the CPU running at: - * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz - */ -#define CONFIG_SYS_CLKDIV_CPU 0 -/* - * Set the HSB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz - */ -#define CONFIG_SYS_CLKDIV_HSB 1 -/* - * Set the PBA running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz - */ -#define CONFIG_SYS_CLKDIV_PBA 2 -/* - * Set the PBB running at: - * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz - */ -#define CONFIG_SYS_CLKDIV_PBB 1 - -/* Reserve VM regions for SDRAM and NOR flash */ -#define CONFIG_SYS_NR_VM_REGIONS 2 - -/* - * The PLLOPT register controls the PLL like this: - * icp = PLLOPT<2> - * ivco = PLLOPT<1:0> - * - * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). - */ -#define CONFIG_SYS_PLL0_OPT 0x04 - -#define CONFIG_USART_BASE ATMEL_BASE_USART1 -#define CONFIG_USART_ID 1 - -/* User serviceable stuff */ -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_STACKSIZE (2048) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTARGS \ - "console=ttyS0 root=mtd3 fbmem=2400k" - -#define CONFIG_BOOTCOMMAND \ - "fsload; bootm $(fileaddr)" - -/* - * Only interrupt autoboot if <space> is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 1 -#define CONFIG_AUTOBOOT -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -/* - * After booting the board for the first time, new ethernet addresses - * should be generated and assigned to the environment variables - * "ethaddr" and "eth1addr". This is normally done during production. - */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MMC - -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_SETGETDCR -#undef CONFIG_CMD_SOURCE -#undef CONFIG_CMD_XIMG - -#define CONFIG_ATMEL_USART -#define CONFIG_MACB -#define CONFIG_PORTMUX_PIO -#define CONFIG_SYS_NR_PIOS 5 -#define CONFIG_SYS_HSDRAMC -#define CONFIG_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_GENERIC_MMC - -#define CONFIG_SYS_DCACHE_LINESZ 32 -#define CONFIG_SYS_ICACHE_LINESZ 32 - -#define CONFIG_NR_DRAM_BANKS 1 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x800000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE -#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE -#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 65536 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) - -#define CONFIG_SYS_MALLOC_LEN (256*1024) - -/* Allow 4MB for the kernel run-time image */ -#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) -#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) - -/* Other configuration settings that shouldn't have to change all that often */ -#define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP - -#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x3f00000) -#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } - -#endif /* __CONFIG_H */

I have this board at work, so I can trun tests on it.

Signed-off-by: Andreas Bießmann andreas.devel@googlemail.com ---

board/atmel/atstk1000/MAINTAINERS | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/board/atmel/atstk1000/MAINTAINERS b/board/atmel/atstk1000/MAINTAINERS index 6143846..1070f98 100644 --- a/board/atmel/atstk1000/MAINTAINERS +++ b/board/atmel/atstk1000/MAINTAINERS @@ -1,6 +1,6 @@ ATSTK1000 BOARD -#M: Haavard Skinnemoen haavard.skinnemoen@atmel.com -S: Orphan (since 2014-06) +M: Andreas Bießmann andreas.biessmann@corscience.de +S: Maintained F: board/atmel/atstk1000/ F: include/configs/atstk1002.h F: configs/atstk1002_defconfig

Signed-off-by: Andreas Bießmann andreas.devel@googlemail.com ---

arch/avr32/lib/Makefile | 3 - arch/avr32/lib/board.c | 256 ------------------------------------------------ 2 files changed, 259 deletions(-) delete mode 100644 arch/avr32/lib/board.c

diff --git a/arch/avr32/lib/Makefile b/arch/avr32/lib/Makefile index 6750913..8108ae5 100644 --- a/arch/avr32/lib/Makefile +++ b/arch/avr32/lib/Makefile @@ -8,9 +8,6 @@ #

obj-y += memset.o -ifndef CONFIG_SYS_GENERIC_BOARD -obj-y += board.o -endif obj-$(CONFIG_CMD_BOOTM) += bootm.o obj-y += interrupts.o obj-y += dram_init.o diff --git a/arch/avr32/lib/board.c b/arch/avr32/lib/board.c deleted file mode 100644 index aacfcbf..0000000 --- a/arch/avr32/lib/board.c +++ /dev/null @@ -1,256 +0,0 @@ -/* - * Copyright (C) 2004-2006 Atmel Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <command.h> -#include <malloc.h> -#include <stdio_dev.h> -#include <version.h> -#include <net.h> - -#ifdef CONFIG_BITBANGMII -#include <miiphy.h> -#endif - -#include <asm/sections.h> -#include <asm/arch/mmu.h> -#include <asm/arch/hardware.h> - -#ifndef CONFIG_IDENT_STRING -#define CONFIG_IDENT_STRING "" -#endif - -#ifdef CONFIG_GENERIC_ATMEL_MCI -#include <mmc.h> -#endif -DECLARE_GLOBAL_DATA_PTR; - -unsigned long monitor_flash_len; - -__weak void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; - gd->bd->bi_dram[0].size = gd->ram_size; -} - -/* Weak aliases for optional board functions */ -static int __do_nothing(void) -{ - return 0; -} -int board_postclk_init(void) __attribute__((weak, alias("__do_nothing"))); -int board_early_init_r(void) __attribute__((weak, alias("__do_nothing"))); - -static int init_baudrate(void) -{ - gd->baudrate = getenv_ulong("baudrate", 10, CONFIG_BAUDRATE); - return 0; -} - -static int display_banner (void) -{ - printf ("\n\n%s\n\n", version_string); - printf ("U-Boot code: %08lx -> %08lx data: %08lx -> %08lx\n", - (unsigned long)_text, (unsigned long)_etext, - (unsigned long)_data, (unsigned long)(&__bss_end)); - return 0; -} - -static int display_dram_config (void) -{ - int i; - - puts ("DRAM Configuration:\n"); - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - printf ("Bank #%d: %08lx ", i, gd->bd->bi_dram[i].start); - print_size (gd->bd->bi_dram[i].size, "\n"); - } - - return 0; -} - -static void display_flash_config (void) -{ - puts ("Flash: "); - print_size(gd->bd->bi_flashsize, " "); - printf("at address 0x%08lx\n", gd->bd->bi_flashstart); -} - -void board_init_f(ulong board_type) -{ - gd_t gd_data; - gd_t *new_gd; - bd_t *bd; - unsigned long *new_sp; - unsigned long monitor_len; - unsigned long monitor_addr; - unsigned long addr; - - /* Initialize the global data pointer */ - memset(&gd_data, 0, sizeof(gd_data)); - gd = &gd_data; - - /* Perform initialization sequence */ - board_early_init_f(); - arch_cpu_init(); - board_postclk_init(); - env_init(); - init_baudrate(); - serial_init(); - console_init_f(); - display_banner(); - dram_init(); - - /* If we have no SDRAM, we can't go on */ - if (gd->ram_size <= 0) - panic("No working SDRAM available\n"); - - /* - * Now that we have DRAM mapped and working, we can - * relocate the code and continue running from DRAM. - * - * Reserve memory at end of RAM for (top down in that order): - * - u-boot image - * - heap for malloc() - * - board info struct - * - global data struct - * - stack - */ - addr = CONFIG_SYS_SDRAM_BASE + gd->ram_size; - monitor_len = (char *)(&__bss_end) - _text; - - /* - * Reserve memory for u-boot code, data and bss. - * Round down to next 4 kB limit. - */ - addr -= monitor_len; - addr &= ~(4096UL - 1); - monitor_addr = addr; - - /* Reserve memory for malloc() */ - addr -= CONFIG_SYS_MALLOC_LEN; - -#ifdef CONFIG_LCD -#ifdef CONFIG_FB_ADDR - printf("LCD: Frame buffer allocated at preset 0x%08x\n", - CONFIG_FB_ADDR); - gd->fb_base = CONFIG_FB_ADDR; -#else - addr = lcd_setmem(addr); - printf("LCD: Frame buffer allocated at 0x%08lx\n", addr); - gd->fb_base = addr; -#endif /* CONFIG_FB_ADDR */ -#endif /* CONFIG_LCD */ - - /* Allocate a Board Info struct on a word boundary */ - addr -= sizeof(bd_t); - addr &= ~3UL; - gd->bd = bd = (bd_t *)addr; - - /* Allocate a new global data copy on a 8-byte boundary. */ - addr -= sizeof(gd_t); - addr &= ~7UL; - new_gd = (gd_t *)addr; - - /* And finally, a new, bigger stack. */ - new_sp = (unsigned long *)addr; - gd->start_addr_sp = addr; - *(--new_sp) = 0; - *(--new_sp) = 0; - - dram_init_banksize(); - - memcpy(new_gd, gd, sizeof(gd_t)); - - relocate_code((unsigned long)new_sp, new_gd, monitor_addr); -} - -void board_init_r(gd_t *new_gd, ulong dest_addr) -{ -#ifndef CONFIG_ENV_IS_NOWHERE - extern char * env_name_spec; -#endif - bd_t *bd; - - gd = new_gd; - bd = gd->bd; - - gd->flags |= GD_FLG_RELOC; - gd->reloc_off = dest_addr - CONFIG_SYS_MONITOR_BASE; - - /* Enable the MMU so that we can keep u-boot simple */ - mmu_init_r(dest_addr); - - board_early_init_r(); - - monitor_flash_len = _edata - _text; - -#if defined(CONFIG_NEEDS_MANUAL_RELOC) - /* - * We have to relocate the command table manually - */ - fixup_cmdtable(ll_entry_start(cmd_tbl_t, cmd), - ll_entry_count(cmd_tbl_t, cmd)); -#endif /* defined(CONFIG_NEEDS_MANUAL_RELOC) */ - - /* there are some other pointer constants we must deal with */ -#ifndef CONFIG_ENV_IS_NOWHERE - env_name_spec += gd->reloc_off; -#endif - - timer_init(); - - /* The malloc area is right below the monitor image in RAM */ - mem_malloc_init(CONFIG_SYS_MONITOR_BASE + gd->reloc_off - - CONFIG_SYS_MALLOC_LEN, CONFIG_SYS_MALLOC_LEN); - - enable_interrupts(); - - bd->bi_flashstart = 0; - bd->bi_flashsize = 0; - bd->bi_flashoffset = 0; - -#ifndef CONFIG_SYS_NO_FLASH - bd->bi_flashstart = CONFIG_SYS_FLASH_BASE; - bd->bi_flashsize = flash_init(); - bd->bi_flashoffset = (unsigned long)_edata - (unsigned long)_text; - - if (bd->bi_flashsize) - display_flash_config(); -#endif - - if (bd->bi_dram[0].size) - display_dram_config(); - - gd->bd->bi_boot_params = malloc(CONFIG_SYS_BOOTPARAMS_LEN); - if (!gd->bd->bi_boot_params) - puts("WARNING: Cannot allocate space for boot parameters\n"); - - /* initialize environment */ - env_relocate(); - - stdio_init(); - jumptable_init(); - console_init_r(); - - /* Initialize from environment */ - load_addr = getenv_ulong("loadaddr", 16, load_addr); - -#ifdef CONFIG_BITBANGMII - bb_miiphy_init(); -#endif -#if defined(CONFIG_CMD_NET) - puts("Net: "); - eth_initialize(); -#endif - -#ifdef CONFIG_GENERIC_ATMEL_MCI - mmc_initialize(gd->bd); -#endif - for (;;) { - main_loop(); - } -}