commit 010a958b (arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h) breaks building keymile arm targets, when u-boot.kwb tries to generate the binary with mkimage. A simple make <board> or MAKEALL succeeded because it don't try to build the kirwood binary at the end.

Due this commit we use the CONFIG_SYS_KWD_CONFIG from the arch-kirkwood/config.h and it was removed from the board config. But it was forgotten to include the header. Now the header is included in km_arm.h. Some other defines were obsolete due to this include, these are also removed in this commit.

Signed-off-by: Holger Brunck holger.brunck@keymile.com cc: Valentin Longchamp valentin.longchamp@keymile.com cc: Prafulla Wadaskar prafulla@marvell.com cc: Heiko Schocher hs@denx.de --- changes for v2: - move CONFIG_KW88F6281 to original place, it was unneeded to touch this for the initial patch

include/configs/km/km_arm.h | 28 ++++++---------------------- include/configs/mgcoge3un.h | 1 + 2 files changed, 7 insertions(+), 22 deletions(-)

diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index 20ee6ea..4741278 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -40,7 +40,6 @@ * High Level Configuration Options (easy to change) */ #define CONFIG_MARVELL -#define CONFIG_ARM926EJS /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */ #define CONFIG_KIRKWOOD /* SOC Family Name */ #define CONFIG_KW88F6281 /* SOC Name */ @@ -49,6 +48,12 @@ /* include common defines/options for all Keymile boards */ #include "keymile-common.h"

+#define CONFIG_CMD_NAND +#define CONFIG_CMD_SF +#define CONFIG_SOFT_I2C /* I2C bit-banged */ + +#include "asm/arch/config.h" + #define CONFIG_SYS_TEXT_BASE 0x04000000 /* code address after reloc */ #define CONFIG_ENV_SIZE (128 << 10) /* NAND chip block size */ #define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ @@ -75,12 +80,7 @@

#define CONFIG_KM_ARCH_DBG_FILE "scripts/debug-arm-env.txt"

-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#undef CONFIG_KIRKWOOD_PCIE_INIT /* Disable PCIE Port0 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - #define CONFIG_MISC_INIT_R

/* @@ -116,7 +116,6 @@ */ #define CONFIG_CMD_ELF #define CONFIG_CMD_MTDPARTS -#define CONFIG_CMD_NAND #define CONFIG_CMD_NFS

/* @@ -131,8 +130,6 @@ */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_NAND_BASE 0xd8000000

#define BOOTFLASH_START 0x0

@@ -175,8 +172,6 @@ /* * I2C related stuff */ -#define CONFIG_SOFT_I2C /* I2C bit-banged */ - #define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */ #if defined(CONFIG_SOFT_I2C) #ifndef __ASSEMBLY__ @@ -200,8 +195,6 @@ int get_scl(void); #define I2C_DELAY udelay(3) /* 1/4 I2C clock duration */ #define I2C_SOFT_DECLARATIONS

-#define CONFIG_SYS_I2C_SLAVE 0x0 -#define CONFIG_SYS_I2C_SPEED 100000 #endif

#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 @@ -224,15 +217,8 @@ int get_scl(void); #define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */ #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

-#define CONFIG_CMD_SF - #define CONFIG_SPI_FLASH -#define CONFIG_HARD_SPI -#define CONFIG_KIRKWOOD_SPI #define CONFIG_SPI_FLASH_STMICRO -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50Mhz */

#define FLASH_GPIO_PIN 0x00010000

@@ -272,8 +258,6 @@ int get_scl(void);

/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 -/* Kirkwood has 2k of Security SRAM, use it for SP */ -#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 /* Do early setups now in board_init_f() */ #define CONFIG_BOARD_EARLY_INIT_F

diff --git a/include/configs/mgcoge3un.h b/include/configs/mgcoge3un.h index 6d56d7d..8d1b61f 100644 --- a/include/configs/mgcoge3un.h +++ b/include/configs/mgcoge3un.h @@ -48,6 +48,7 @@ #define KM_ENV_BUS "pca9547:70:d" /* I2C2 (Mux-Port 5)*/

/* we use a new RAM type on mgcoge3un board */ +#undef CONFIG_SYS_KWD_CONFIG #define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg

/*

-----Original Message----- From: Holger Brunck [mailto:holger.brunck@keymile.com] Sent: Wednesday, June 15, 2011 1:42 PM To: u-boot@lists.denx.de Cc: Holger Brunck; Valentin Longchamp; Prafulla Wadaskar; Heiko Schocher Subject: [PATCH v2 1/2] arm/kirkwood: if CONFIG_SOFT_I2C is set don't set CONFIG_I2C_MVTWSI

Some boards e.g. keymile arm boards have CONFIG_CMD_I2C switched on but they use soft i2c on kirkwood. So don't switch CONFIG_I2C_MVTWSI on in this case.

Signed-off-by: Holger Brunck holger.brunck@keymile.com cc: Valentin Longchamp valentin.longchamp@keymile.com cc: Prafulla Wadaskar prafulla@marvell.com cc: Heiko Schocher hs@denx.de

---

changes for v2:

• nothing

arch/arm/include/asm/arch-kirkwood/config.h | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h index 71ba464..b7dae1e 100644 --- a/arch/arm/include/asm/arch-kirkwood/config.h +++ b/arch/arm/include/asm/arch-kirkwood/config.h @@ -137,7 +137,9 @@

• I2C related stuff

*/ #ifdef CONFIG_CMD_I2C +#ifndef CONFIG_SOFT_I2C #define CONFIG_I2C_MVTWSI +#endif #define CONFIG_SYS_I2C_SLAVE 0x0 #define CONFIG_SYS_I2C_SPEED 100000 #endif

Applied to u-boot-marvell.git next brach

Regards.. Prafulla . .

-- 1.7.1