[U-Boot] [PATCH V2 0/9] Add Device Tree for OMAP3 and omap3_logic
This patch series copies the Linux Device trees for the OMAP3 and OMAP3630 platforms as well as some additional device trees to support the Logic PD Torpedo and Logic PD SOM-LV both based on DM3730 (OMAP3630) processors. There are no changes to patches 2-6 from the initial version posted as RFC, but I added "Reviewed-by: Lokesh Vutla lokeshvutla@ti.com" to patches 2-6
Part 1 Changes the method for the MMC base address offsets to be caluclated. These offsets are different between OMAP3 and am33xx and omap4+. This moves away from an #ifdef method to a method of that uses .compatible to determine the offset. This is needed for OMAP3 device tree support.
This rest of this series allows us move to DM_I2C and DM_MMC and push the DM_SERIAL setup to the OF except when in SPL. This should give enough background for other OMAP3 boards to migrate to device tree.
The dm uclass dump is as follows:
uclass 0: root - * root_driver @ 8df38028, seq 0, (req -1)
uclass 9: simple_bus - * ocp@68000000 @ 8df382e0, seq 0, (req -1) - l4@48000000 @ 8df38348 - scm@2000 @ 8df383b0 - scm_conf@270 @ 8df38418
uclass 19: gpio - gpio_omap @ 8df380b0 - gpio_omap @ 8df38108 - gpio_omap @ 8df38160 - gpio_omap @ 8df381b8 - gpio_omap @ 8df38210 - gpio_omap @ 8df38268 - gpio@48310000 @ 8df38480 - gpio@49050000 @ 8df384e8 - gpio@49052000 @ 8df38550 - * gpio@49054000 @ 8df385b8, seq 0, (req -1) - gpio@49056000 @ 8df38620 - gpio@49058000 @ 8df38688
uclass 20: i2c - * i2c@48070000 @ 8df38880, seq 0, (req 0) - i2c@48072000 @ 8df388d8, seq -1, (req 1) - i2c@48060000 @ 8df38930, seq -1, (req 2)
uclass 22: i2c_generic - * generic_4b @ 8df4b178, seq 0, (req -1)
uclass 31: mmc - * mmc@4809c000 @ 8df389a8, seq 0, (req -1) - * mmc@480ad000 @ 8df38b80, seq 1, (req -1)
uclass 52: serial - * serial@4806a000 @ 8df38710, seq 0, (req 0) - serial@4806c000 @ 8df38780, seq -1, (req 1) - serial@49020000 @ 8df387f0, seq -1, (req 2) - serial@49042000 @ 8df38d58, seq -1, (req 3)
Adam Ford (9): omap_hsmmc: update struct hsmmc to accommodate omap3 from DT omap3: Copy Device tree from Linux 4.9.y stable omap3630: Copy Device tree from Linux 4.9.y stable ARM: OMAP: I2C: Support New read, write and probe functions for OMAP3 omap3: Copy twl4030 device tree from Linux 4.9.y stable OMAP3: Add SMSC9221 device tree for omap devices connected on GPMC. ARM: DTS: Add Logic PD DM3730 SOM-LV initial support ARM: DTS: Add Logic PD DM3730 Torpedo Device Tree omap3_logic: Add Device Tree Support and more DM drivers
arch/arm/dts/Makefile | 4 + arch/arm/dts/logicpd-som-lv-37xx-devkit.dts | 269 ++++ arch/arm/dts/logicpd-som-lv.dtsi | 271 ++++ arch/arm/dts/logicpd-torpedo-37xx-devkit.dts | 411 +++++ arch/arm/dts/logicpd-torpedo-som.dtsi | 217 +++ arch/arm/dts/omap-gpmc-smsc9221.dtsi | 58 + arch/arm/dts/omap3.dtsi | 854 ++++++++++ arch/arm/dts/omap34xx-omap36xx-clocks.dtsi | 268 ++++ .../omap36xx-am35xx-omap3430es2plus-clocks.dtsi | 242 +++ arch/arm/dts/omap36xx-clocks.dtsi | 110 ++ arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi | 198 +++ arch/arm/dts/omap36xx.dtsi | 118 ++ arch/arm/dts/omap3xxx-clocks.dtsi | 1665 ++++++++++++++++++++ arch/arm/dts/twl4030.dtsi | 161 ++ arch/arm/dts/twl4030_omap3.dtsi | 42 + arch/arm/include/asm/omap_mmc.h | 3 - board/logicpd/omap3som/README | 19 + board/logicpd/omap3som/omap3logic.c | 18 +- configs/omap3_logic_defconfig | 8 +- drivers/i2c/omap24xx_i2c.c | 1 + drivers/mmc/omap_hsmmc.c | 35 +- include/configs/omap3_logic.h | 25 +- include/dt-bindings/media/omap3-isp.h | 22 + 23 files changed, 4993 insertions(+), 26 deletions(-) create mode 100644 arch/arm/dts/logicpd-som-lv-37xx-devkit.dts create mode 100644 arch/arm/dts/logicpd-som-lv.dtsi create mode 100644 arch/arm/dts/logicpd-torpedo-37xx-devkit.dts create mode 100644 arch/arm/dts/logicpd-torpedo-som.dtsi create mode 100644 arch/arm/dts/omap-gpmc-smsc9221.dtsi create mode 100644 arch/arm/dts/omap3.dtsi create mode 100644 arch/arm/dts/omap34xx-omap36xx-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx.dtsi create mode 100644 arch/arm/dts/omap3xxx-clocks.dtsi create mode 100644 arch/arm/dts/twl4030.dtsi create mode 100644 arch/arm/dts/twl4030_omap3.dtsi create mode 100644 board/logicpd/omap3som/README create mode 100644 include/dt-bindings/media/omap3-isp.h
This patch changes the way DM_MMC calculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the .compatible flags.
Signed-off-by: Adam Ford aford173@gmail.com
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3
diff --git a/arch/arm/include/asm/omap_mmc.h b/arch/arm/include/asm/omap_mmc.h index f2bf645..93e003a 100644 --- a/arch/arm/include/asm/omap_mmc.h +++ b/arch/arm/include/asm/omap_mmc.h @@ -26,9 +26,6 @@ #define OMAP_MMC_H_
struct hsmmc { -#ifdef CONFIG_DM_MMC - unsigned char res0[0x100]; -#endif unsigned char res1[0x10]; unsigned int sysconfig; /* 0x10 */ unsigned int sysstatus; /* 0x14 */ diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c index 83dda09..d151fe7 100644 --- a/drivers/mmc/omap_hsmmc.c +++ b/drivers/mmc/omap_hsmmc.c @@ -61,6 +61,10 @@ struct omap_hsmmc_plat { struct mmc mmc; };
+struct omap2_mmc_platform_config { + u32 reg_offset; +}; + struct omap_hsmmc_data { struct hsmmc *base_addr; #ifndef CONFIG_DM_MMC @@ -778,12 +782,14 @@ static int omap_hsmmc_ofdata_to_platdata(struct udevice *dev) struct omap_hsmmc_data *priv = dev_get_priv(dev); struct omap_hsmmc_plat *plat = dev_get_platdata(dev); struct mmc_config *cfg = &plat->cfg; + struct omap2_mmc_platform_config *data = + (struct omap2_mmc_platform_config *)dev_get_driver_data(dev); const void *fdt = gd->fdt_blob; int node = dev_of_offset(dev); int val;
priv->base_addr = map_physmem(dev_get_addr(dev), sizeof(struct hsmmc *), - MAP_NOCACHE); + MAP_NOCACHE) + data->reg_offset;
cfg->host_caps = MMC_MODE_HS_52MHz | MMC_MODE_HS; val = fdtdec_get_int(fdt, node, "bus-width", -1); @@ -854,10 +860,31 @@ static int omap_hsmmc_probe(struct udevice *dev) return 0; }
+static const struct omap2_mmc_platform_config omap3_mmc_pdata = { + .reg_offset = 0, +}; + +static const struct omap2_mmc_platform_config am33xx_mmc_pdata = { + .reg_offset = 0x100, +}; + +static const struct omap2_mmc_platform_config omap4_mmc_pdata = { + .reg_offset = 0x100, +}; + static const struct udevice_id omap_hsmmc_ids[] = { - { .compatible = "ti,omap3-hsmmc" }, - { .compatible = "ti,omap4-hsmmc" }, - { .compatible = "ti,am33xx-hsmmc" }, + { + .compatible = "ti,omap3-hsmmc", + .data = (ulong)&omap3_mmc_pdata + }, + { + .compatible = "ti,omap4-hsmmc", + .data = (ulong)&omap4_mmc_pdata + }, + { + .compatible = "ti,am33xx-hsmmc", + .data = (ulong)&am33xx_mmc_pdata + }, { } };
On Monday 17 April 2017 06:39 PM, Adam Ford wrote:
This patch changes the way DM_MMC calculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the .compatible flags.
Signed-off-by: Adam Ford aford173@gmail.com
Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
Thanks and regards, Lokesh
On 25 April 2017 at 22:57, Lokesh Vutla lokeshvutla@ti.com wrote:
On Monday 17 April 2017 06:39 PM, Adam Ford wrote:
This patch changes the way DM_MMC calculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the .compatible flags.
Signed-off-by: Adam Ford aford173@gmail.com
Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
Thanks and regards, Lokesh
Reviewed-by: Simon Glass sjg@chromium.org
On Mon, Apr 17, 2017 at 08:09:37AM -0500, Adam Ford wrote:
This patch changes the way DM_MMC calculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the .compatible flags.
Signed-off-by: Adam Ford aford173@gmail.com
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3 Reviewed-by: Lokesh Vutla lokeshvutla@ti.com Reviewed-by: Simon Glass sjg@chromium.org
diff --git a/arch/arm/include/asm/omap_mmc.h b/arch/arm/include/asm/omap_mmc.h index f2bf645..93e003a 100644
Applied to u-boot/master, thanks!
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/omap3.dtsi b/arch/arm/dts/omap3.dtsi new file mode 100644 index 0000000..a0f2412 --- /dev/null +++ b/arch/arm/dts/omap3.dtsi @@ -0,0 +1,854 @@ +/* + * Device Tree Source for OMAP3 SoC + * + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/omap.h> + +/ { + compatible = "ti,omap3430", "ti,omap3"; + interrupt-parent = <&intc>; + #address-cells = <1>; + #size-cells = <1>; + chosen { }; + + aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a8"; + device_type = "cpu"; + reg = <0x0>; + + clocks = <&dpll1_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + }; + }; + + pmu@54000000 { + compatible = "arm,cortex-a8-pmu"; + reg = <0x54000000 0x800000>; + interrupts = <3>; + ti,hwmods = "debugss"; + }; + + /* + * The soc node represents the soc top level view. It is used for IPs + * that are not memory mapped in the MPU view or for the MPU itself. + */ + soc { + compatible = "ti,omap-infra"; + mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; + }; + + iva: iva { + compatible = "ti,iva2.2"; + ti,hwmods = "iva"; + + dsp { + compatible = "ti,omap3-c64"; + }; + }; + }; + + /* + * XXX: Use a flat representation of the OMAP3 interconnect. + * The real OMAP interconnect network is quite complex. + * Since it will not bring real advantage to represent that in DT for + * the moment, just use a fake OCP bus entry to represent the whole bus + * hierarchy. + */ + ocp@68000000 { + compatible = "ti,omap3-l3-smx", "simple-bus"; + reg = <0x68000000 0x10000>; + interrupts = <9 10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "l3_main"; + + l4_core: l4@48000000 { + compatible = "ti,omap3-l4-core", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48000000 0x1000000>; + + scm: scm@2000 { + compatible = "ti,omap3-scm", "simple-bus"; + reg = <0x2000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + omap3_pmx_core: pinmux@30 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0x30 0x238>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + + scm_conf: scm_conf@270 { + compatible = "syscon", "simple-bus"; + reg = <0x270 0x330>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x270 0x330>; + + pbias_regulator: pbias_regulator@2b0 { + compatible = "ti,pbias-omap3", "ti,pbias-omap"; + reg = <0x2b0 0x4>; + syscon = <&scm_conf>; + pbias_mmc_reg: pbias_mmc_omap2430 { + regulator-name = "pbias_mmc_omap2430"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; + + omap3_pmx_wkup: pinmux@a00 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0xa00 0x5c>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + }; + }; + + aes: aes@480c5000 { + compatible = "ti,omap3-aes"; + ti,hwmods = "aes"; + reg = <0x480c5000 0x50>; + interrupts = <0>; + dmas = <&sdma 65 &sdma 66>; + dma-names = "tx", "rx"; + }; + + prm: prm@48306000 { + compatible = "ti,omap3-prm"; + reg = <0x48306000 0x4000>; + interrupts = <11>; + + prm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prm_clockdomains: clockdomains { + }; + }; + + cm: cm@48004000 { + compatible = "ti,omap3-cm"; + reg = <0x48004000 0x4000>; + + cm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_clockdomains: clockdomains { + }; + }; + + counter32k: counter@48320000 { + compatible = "ti,omap-counter32k"; + reg = <0x48320000 0x20>; + ti,hwmods = "counter_32k"; + }; + + intc: interrupt-controller@48200000 { + compatible = "ti,omap3-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x48200000 0x1000>; + }; + + sdma: dma-controller@48056000 { + compatible = "ti,omap3630-sdma", "ti,omap3430-sdma"; + reg = <0x48056000 0x1000>; + interrupts = <12>, + <13>, + <14>, + <15>; + #dma-cells = <1>; + dma-channels = <32>; + dma-requests = <96>; + }; + + gpio1: gpio@48310000 { + compatible = "ti,omap3-gpio"; + reg = <0x48310000 0x200>; + interrupts = <29>; + ti,hwmods = "gpio1"; + ti,gpio-always-on; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@49050000 { + compatible = "ti,omap3-gpio"; + reg = <0x49050000 0x200>; + interrupts = <30>; + ti,hwmods = "gpio2"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@49052000 { + compatible = "ti,omap3-gpio"; + reg = <0x49052000 0x200>; + interrupts = <31>; + ti,hwmods = "gpio3"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@49054000 { + compatible = "ti,omap3-gpio"; + reg = <0x49054000 0x200>; + interrupts = <32>; + ti,hwmods = "gpio4"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio5: gpio@49056000 { + compatible = "ti,omap3-gpio"; + reg = <0x49056000 0x200>; + interrupts = <33>; + ti,hwmods = "gpio5"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio6: gpio@49058000 { + compatible = "ti,omap3-gpio"; + reg = <0x49058000 0x200>; + interrupts = <34>; + ti,hwmods = "gpio6"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart1: serial@4806a000 { + compatible = "ti,omap3-uart"; + reg = <0x4806a000 0x2000>; + reg-shift = <2>; + interrupts-extended = <&intc 72>; + dmas = <&sdma 49 &sdma 50>; + dma-names = "tx", "rx"; + ti,hwmods = "uart1"; + clock-frequency = <48000000>; + }; + + uart2: serial@4806c000 { + compatible = "ti,omap3-uart"; + reg = <0x4806c000 0x400>; + interrupts-extended = <&intc 73>; + dmas = <&sdma 51 &sdma 52>; + dma-names = "tx", "rx"; + ti,hwmods = "uart2"; + clock-frequency = <48000000>; + }; + + uart3: serial@49020000 { + compatible = "ti,omap3-uart"; + reg = <0x49020000 0x400>; + interrupts-extended = <&intc 74>; + dmas = <&sdma 53 &sdma 54>; + dma-names = "tx", "rx"; + ti,hwmods = "uart3"; + clock-frequency = <48000000>; + }; + + i2c1: i2c@48070000 { + compatible = "ti,omap3-i2c"; + reg = <0x48070000 0x80>; + interrupts = <56>; + dmas = <&sdma 27 &sdma 28>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + }; + + i2c2: i2c@48072000 { + compatible = "ti,omap3-i2c"; + reg = <0x48072000 0x80>; + interrupts = <57>; + dmas = <&sdma 29 &sdma 30>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c2"; + }; + + i2c3: i2c@48060000 { + compatible = "ti,omap3-i2c"; + reg = <0x48060000 0x80>; + interrupts = <61>; + dmas = <&sdma 25 &sdma 26>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c3"; + }; + + mailbox: mailbox@48094000 { + compatible = "ti,omap3-mailbox"; + ti,hwmods = "mailbox"; + reg = <0x48094000 0x200>; + interrupts = <26>; + #mbox-cells = <1>; + ti,mbox-num-users = <2>; + ti,mbox-num-fifos = <2>; + mbox_dsp: dsp { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <1 0 0>; + }; + }; + + mcspi1: spi@48098000 { + compatible = "ti,omap2-mcspi"; + reg = <0x48098000 0x100>; + interrupts = <65>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; + dmas = <&sdma 35>, + <&sdma 36>, + <&sdma 37>, + <&sdma 38>, + <&sdma 39>, + <&sdma 40>, + <&sdma 41>, + <&sdma 42>; + dma-names = "tx0", "rx0", "tx1", "rx1", + "tx2", "rx2", "tx3", "rx3"; + }; + + mcspi2: spi@4809a000 { + compatible = "ti,omap2-mcspi"; + reg = <0x4809a000 0x100>; + interrupts = <66>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi2"; + ti,spi-num-cs = <2>; + dmas = <&sdma 43>, + <&sdma 44>, + <&sdma 45>, + <&sdma 46>; + dma-names = "tx0", "rx0", "tx1", "rx1"; + }; + + mcspi3: spi@480b8000 { + compatible = "ti,omap2-mcspi"; + reg = <0x480b8000 0x100>; + interrupts = <91>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi3"; + ti,spi-num-cs = <2>; + dmas = <&sdma 15>, + <&sdma 16>, + <&sdma 23>, + <&sdma 24>; + dma-names = "tx0", "rx0", "tx1", "rx1"; + }; + + mcspi4: spi@480ba000 { + compatible = "ti,omap2-mcspi"; + reg = <0x480ba000 0x100>; + interrupts = <48>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi4"; + ti,spi-num-cs = <1>; + dmas = <&sdma 70>, <&sdma 71>; + dma-names = "tx0", "rx0"; + }; + + hdqw1w: 1w@480b2000 { + compatible = "ti,omap3-1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + ti,hwmods = "hdq1w"; + }; + + mmc1: mmc@4809c000 { + compatible = "ti,omap3-hsmmc"; + reg = <0x4809c000 0x200>; + interrupts = <83>; + ti,hwmods = "mmc1"; + ti,dual-volt; + dmas = <&sdma 61>, <&sdma 62>; + dma-names = "tx", "rx"; + pbias-supply = <&pbias_mmc_reg>; + }; + + mmc2: mmc@480b4000 { + compatible = "ti,omap3-hsmmc"; + reg = <0x480b4000 0x200>; + interrupts = <86>; + ti,hwmods = "mmc2"; + dmas = <&sdma 47>, <&sdma 48>; + dma-names = "tx", "rx"; + }; + + mmc3: mmc@480ad000 { + compatible = "ti,omap3-hsmmc"; + reg = <0x480ad000 0x200>; + interrupts = <94>; + ti,hwmods = "mmc3"; + dmas = <&sdma 77>, <&sdma 78>; + dma-names = "tx", "rx"; + }; + + mmu_isp: mmu@480bd400 { + #iommu-cells = <0>; + compatible = "ti,omap2-iommu"; + reg = <0x480bd400 0x80>; + interrupts = <24>; + ti,hwmods = "mmu_isp"; + ti,#tlb-entries = <8>; + }; + + mmu_iva: mmu@5d000000 { + #iommu-cells = <0>; + compatible = "ti,omap2-iommu"; + reg = <0x5d000000 0x80>; + interrupts = <28>; + ti,hwmods = "mmu_iva"; + status = "disabled"; + }; + + wdt2: wdt@48314000 { + compatible = "ti,omap3-wdt"; + reg = <0x48314000 0x80>; + ti,hwmods = "wd_timer2"; + }; + + mcbsp1: mcbsp@48074000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x48074000 0xff>; + reg-names = "mpu"; + interrupts = <16>, /* OCP compliant interrupt */ + <59>, /* TX interrupt */ + <60>; /* RX interrupt */ + interrupt-names = "common", "tx", "rx"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp1"; + dmas = <&sdma 31>, + <&sdma 32>; + dma-names = "tx", "rx"; + clocks = <&mcbsp1_fck>; + clock-names = "fck"; + status = "disabled"; + }; + + mcbsp2: mcbsp@49022000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49022000 0xff>, + <0x49028000 0xff>; + reg-names = "mpu", "sidetone"; + interrupts = <17>, /* OCP compliant interrupt */ + <62>, /* TX interrupt */ + <63>, /* RX interrupt */ + <4>; /* Sidetone */ + interrupt-names = "common", "tx", "rx", "sidetone"; + ti,buffer-size = <1280>; + ti,hwmods = "mcbsp2", "mcbsp2_sidetone"; + dmas = <&sdma 33>, + <&sdma 34>; + dma-names = "tx", "rx"; + clocks = <&mcbsp2_fck>, <&mcbsp2_ick>; + clock-names = "fck", "ick"; + status = "disabled"; + }; + + mcbsp3: mcbsp@49024000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49024000 0xff>, + <0x4902a000 0xff>; + reg-names = "mpu", "sidetone"; + interrupts = <22>, /* OCP compliant interrupt */ + <89>, /* TX interrupt */ + <90>, /* RX interrupt */ + <5>; /* Sidetone */ + interrupt-names = "common", "tx", "rx", "sidetone"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp3", "mcbsp3_sidetone"; + dmas = <&sdma 17>, + <&sdma 18>; + dma-names = "tx", "rx"; + clocks = <&mcbsp3_fck>, <&mcbsp3_ick>; + clock-names = "fck", "ick"; + status = "disabled"; + }; + + mcbsp4: mcbsp@49026000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49026000 0xff>; + reg-names = "mpu"; + interrupts = <23>, /* OCP compliant interrupt */ + <54>, /* TX interrupt */ + <55>; /* RX interrupt */ + interrupt-names = "common", "tx", "rx"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp4"; + dmas = <&sdma 19>, + <&sdma 20>; + dma-names = "tx", "rx"; + clocks = <&mcbsp4_fck>; + clock-names = "fck"; + status = "disabled"; + }; + + mcbsp5: mcbsp@48096000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x48096000 0xff>; + reg-names = "mpu"; + interrupts = <27>, /* OCP compliant interrupt */ + <81>, /* TX interrupt */ + <82>; /* RX interrupt */ + interrupt-names = "common", "tx", "rx"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp5"; + dmas = <&sdma 21>, + <&sdma 22>; + dma-names = "tx", "rx"; + clocks = <&mcbsp5_fck>; + clock-names = "fck"; + status = "disabled"; + }; + + sham: sham@480c3000 { + compatible = "ti,omap3-sham"; + ti,hwmods = "sham"; + reg = <0x480c3000 0x64>; + interrupts = <49>; + dmas = <&sdma 69>; + dma-names = "rx"; + }; + + smartreflex_core: smartreflex@480cb000 { + compatible = "ti,omap3-smartreflex-core"; + ti,hwmods = "smartreflex_core"; + reg = <0x480cb000 0x400>; + interrupts = <19>; + }; + + smartreflex_mpu_iva: smartreflex@480c9000 { + compatible = "ti,omap3-smartreflex-iva"; + ti,hwmods = "smartreflex_mpu_iva"; + reg = <0x480c9000 0x400>; + interrupts = <18>; + }; + + timer1: timer@48318000 { + compatible = "ti,omap3430-timer"; + reg = <0x48318000 0x400>; + interrupts = <37>; + ti,hwmods = "timer1"; + ti,timer-alwon; + }; + + timer2: timer@49032000 { + compatible = "ti,omap3430-timer"; + reg = <0x49032000 0x400>; + interrupts = <38>; + ti,hwmods = "timer2"; + }; + + timer3: timer@49034000 { + compatible = "ti,omap3430-timer"; + reg = <0x49034000 0x400>; + interrupts = <39>; + ti,hwmods = "timer3"; + }; + + timer4: timer@49036000 { + compatible = "ti,omap3430-timer"; + reg = <0x49036000 0x400>; + interrupts = <40>; + ti,hwmods = "timer4"; + }; + + timer5: timer@49038000 { + compatible = "ti,omap3430-timer"; + reg = <0x49038000 0x400>; + interrupts = <41>; + ti,hwmods = "timer5"; + ti,timer-dsp; + }; + + timer6: timer@4903a000 { + compatible = "ti,omap3430-timer"; + reg = <0x4903a000 0x400>; + interrupts = <42>; + ti,hwmods = "timer6"; + ti,timer-dsp; + }; + + timer7: timer@4903c000 { + compatible = "ti,omap3430-timer"; + reg = <0x4903c000 0x400>; + interrupts = <43>; + ti,hwmods = "timer7"; + ti,timer-dsp; + }; + + timer8: timer@4903e000 { + compatible = "ti,omap3430-timer"; + reg = <0x4903e000 0x400>; + interrupts = <44>; + ti,hwmods = "timer8"; + ti,timer-pwm; + ti,timer-dsp; + }; + + timer9: timer@49040000 { + compatible = "ti,omap3430-timer"; + reg = <0x49040000 0x400>; + interrupts = <45>; + ti,hwmods = "timer9"; + ti,timer-pwm; + }; + + timer10: timer@48086000 { + compatible = "ti,omap3430-timer"; + reg = <0x48086000 0x400>; + interrupts = <46>; + ti,hwmods = "timer10"; + ti,timer-pwm; + }; + + timer11: timer@48088000 { + compatible = "ti,omap3430-timer"; + reg = <0x48088000 0x400>; + interrupts = <47>; + ti,hwmods = "timer11"; + ti,timer-pwm; + }; + + timer12: timer@48304000 { + compatible = "ti,omap3430-timer"; + reg = <0x48304000 0x400>; + interrupts = <95>; + ti,hwmods = "timer12"; + ti,timer-alwon; + ti,timer-secure; + }; + + usbhstll: usbhstll@48062000 { + compatible = "ti,usbhs-tll"; + reg = <0x48062000 0x1000>; + interrupts = <78>; + ti,hwmods = "usb_tll_hs"; + }; + + usbhshost: usbhshost@48064000 { + compatible = "ti,usbhs-host"; + reg = <0x48064000 0x400>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci@48064400 { + compatible = "ti,ohci-omap3"; + reg = <0x48064400 0x400>; + interrupt-parent = <&intc>; + interrupts = <76>; + }; + + usbhsehci: ehci@48064800 { + compatible = "ti,ehci-omap"; + reg = <0x48064800 0x400>; + interrupt-parent = <&intc>; + interrupts = <77>; + }; + }; + + gpmc: gpmc@6e000000 { + compatible = "ti,omap3430-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x02d0>; + interrupts = <20>; + dmas = <&sdma 4>; + dma-names = "rxtx"; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + + usb_otg_hs: usb_otg_hs@480ab000 { + compatible = "ti,omap3-musb"; + reg = <0x480ab000 0x1000>; + interrupts = <92>, <93>; + interrupt-names = "mc", "dma"; + ti,hwmods = "usb_otg_hs"; + multipoint = <1>; + num-eps = <16>; + ram-bits = <12>; + }; + + dss: dss@48050000 { + compatible = "ti,omap3-dss"; + reg = <0x48050000 0x200>; + status = "disabled"; + ti,hwmods = "dss_core"; + clocks = <&dss1_alwon_fck>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dispc@48050400 { + compatible = "ti,omap3-dispc"; + reg = <0x48050400 0x400>; + interrupts = <25>; + ti,hwmods = "dss_dispc"; + clocks = <&dss1_alwon_fck>; + clock-names = "fck"; + }; + + dsi: encoder@4804fc00 { + compatible = "ti,omap3-dsi"; + reg = <0x4804fc00 0x200>, + <0x4804fe00 0x40>, + <0x4804ff00 0x20>; + reg-names = "proto", "phy", "pll"; + interrupts = <25>; + status = "disabled"; + ti,hwmods = "dss_dsi1"; + clocks = <&dss1_alwon_fck>, <&dss2_alwon_fck>; + clock-names = "fck", "sys_clk"; + }; + + rfbi: encoder@48050800 { + compatible = "ti,omap3-rfbi"; + reg = <0x48050800 0x100>; + status = "disabled"; + ti,hwmods = "dss_rfbi"; + clocks = <&dss1_alwon_fck>, <&dss_ick>; + clock-names = "fck", "ick"; + }; + + venc: encoder@48050c00 { + compatible = "ti,omap3-venc"; + reg = <0x48050c00 0x100>; + status = "disabled"; + ti,hwmods = "dss_venc"; + clocks = <&dss_tv_fck>; + clock-names = "fck"; + }; + }; + + ssi: ssi-controller@48058000 { + compatible = "ti,omap3-ssi"; + ti,hwmods = "ssi"; + + status = "disabled"; + + reg = <0x48058000 0x1000>, + <0x48059000 0x1000>; + reg-names = "sys", + "gdd"; + + interrupts = <71>; + interrupt-names = "gdd_mpu"; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ssi_port1: ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805a000 0x800>, + <0x4805a800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <67>, + <68>; + }; + + ssi_port2: ssi-port@4805b000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805b000 0x800>, + <0x4805b800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <69>, + <70>; + }; + }; + }; +}; + +/include/ "omap3xxx-clocks.dtsi" diff --git a/arch/arm/dts/omap3xxx-clocks.dtsi b/arch/arm/dts/omap3xxx-clocks.dtsi new file mode 100644 index 0000000..7455ab5 --- /dev/null +++ b/arch/arm/dts/omap3xxx-clocks.dtsi @@ -0,0 +1,1665 @@ +/* + * Device Tree Source for OMAP3 clock data + * + * Copyright (C) 2013 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +&prm_clocks { + virt_16_8m_ck: virt_16_8m_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <16800000>; + }; + + osc_sys_ck: osc_sys_ck@d40 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&virt_12m_ck>, <&virt_13m_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_38_4m_ck>, <&virt_16_8m_ck>; + reg = <0x0d40>; + }; + + sys_ck: sys_ck@1270 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&osc_sys_ck>; + ti,bit-shift = <6>; + ti,max-div = <3>; + reg = <0x1270>; + ti,index-starts-at-one; + }; + + sys_clkout1: sys_clkout1@d70 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&osc_sys_ck>; + reg = <0x0d70>; + ti,bit-shift = <7>; + }; + + dpll3_x2_ck: dpll3_x2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll3_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + dpll3_m2x2_ck: dpll3_m2x2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll3_m2_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + dpll4_x2_ck: dpll4_x2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll4_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + corex2_fck: corex2_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll3_m2x2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + wkup_l4_ick: wkup_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_ck>; + clock-mult = <1>; + clock-div = <1>; + }; +}; + +&scm_clocks { + mcbsp5_mux_fck: mcbsp5_mux_fck@68 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <4>; + reg = <0x68>; + }; + + mcbsp5_fck: mcbsp5_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&mcbsp5_gate_fck>, <&mcbsp5_mux_fck>; + }; + + mcbsp1_mux_fck: mcbsp1_mux_fck@4 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <2>; + reg = <0x04>; + }; + + mcbsp1_fck: mcbsp1_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&mcbsp1_gate_fck>, <&mcbsp1_mux_fck>; + }; + + mcbsp2_mux_fck: mcbsp2_mux_fck@4 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&per_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <6>; + reg = <0x04>; + }; + + mcbsp2_fck: mcbsp2_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&mcbsp2_gate_fck>, <&mcbsp2_mux_fck>; + }; + + mcbsp3_mux_fck: mcbsp3_mux_fck@68 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&per_96m_fck>, <&mcbsp_clks>; + reg = <0x68>; + }; + + mcbsp3_fck: mcbsp3_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&mcbsp3_gate_fck>, <&mcbsp3_mux_fck>; + }; + + mcbsp4_mux_fck: mcbsp4_mux_fck@68 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&per_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <2>; + reg = <0x68>; + }; + + mcbsp4_fck: mcbsp4_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&mcbsp4_gate_fck>, <&mcbsp4_mux_fck>; + }; +}; +&cm_clocks { + dummy_apb_pclk: dummy_apb_pclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0x0>; + }; + + omap_32k_fck: omap_32k_fck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + }; + + virt_12m_ck: virt_12m_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <12000000>; + }; + + virt_13m_ck: virt_13m_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <13000000>; + }; + + virt_19200000_ck: virt_19200000_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <19200000>; + }; + + virt_26000000_ck: virt_26000000_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; + + virt_38_4m_ck: virt_38_4m_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <38400000>; + }; + + dpll4_ck: dpll4_ck@d00 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-per-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0d00>, <0x0d20>, <0x0d44>, <0x0d30>; + }; + + dpll4_m2_ck: dpll4_m2_ck@d48 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll4_ck>; + ti,max-div = <63>; + reg = <0x0d48>; + ti,index-starts-at-one; + }; + + dpll4_m2x2_mul_ck: dpll4_m2x2_mul_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll4_m2_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + dpll4_m2x2_ck: dpll4_m2x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll4_m2x2_mul_ck>; + ti,bit-shift = <0x1b>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + omap_96m_alwon_fck: omap_96m_alwon_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll4_m2x2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + dpll3_ck: dpll3_ck@d00 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-core-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0d00>, <0x0d20>, <0x0d40>, <0x0d30>; + }; + + dpll3_m3_ck: dpll3_m3_ck@1140 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll3_ck>; + ti,bit-shift = <16>; + ti,max-div = <31>; + reg = <0x1140>; + ti,index-starts-at-one; + }; + + dpll3_m3x2_mul_ck: dpll3_m3x2_mul_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll3_m3_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + dpll3_m3x2_ck: dpll3_m3x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll3_m3x2_mul_ck>; + ti,bit-shift = <0xc>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + emu_core_alwon_ck: emu_core_alwon_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll3_m3x2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + sys_altclk: sys_altclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0x0>; + }; + + mcbsp_clks: mcbsp_clks { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0x0>; + }; + + dpll3_m2_ck: dpll3_m2_ck@d40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll3_ck>; + ti,bit-shift = <27>; + ti,max-div = <31>; + reg = <0x0d40>; + ti,index-starts-at-one; + }; + + core_ck: core_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll3_m2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + dpll1_fck: dpll1_fck@940 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&core_ck>; + ti,bit-shift = <19>; + ti,max-div = <7>; + reg = <0x0940>; + ti,index-starts-at-one; + }; + + dpll1_ck: dpll1_ck@904 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-clock"; + clocks = <&sys_ck>, <&dpll1_fck>; + reg = <0x0904>, <0x0924>, <0x0940>, <0x0934>; + }; + + dpll1_x2_ck: dpll1_x2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll1_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + dpll1_x2m2_ck: dpll1_x2m2_ck@944 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll1_x2_ck>; + ti,max-div = <31>; + reg = <0x0944>; + ti,index-starts-at-one; + }; + + cm_96m_fck: cm_96m_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_96m_alwon_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + omap_96m_fck: omap_96m_fck@d40 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&cm_96m_fck>, <&sys_ck>; + ti,bit-shift = <6>; + reg = <0x0d40>; + }; + + dpll4_m3_ck: dpll4_m3_ck@e40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll4_ck>; + ti,bit-shift = <8>; + ti,max-div = <32>; + reg = <0x0e40>; + ti,index-starts-at-one; + }; + + dpll4_m3x2_mul_ck: dpll4_m3x2_mul_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll4_m3_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + dpll4_m3x2_ck: dpll4_m3x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll4_m3x2_mul_ck>; + ti,bit-shift = <0x1c>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + omap_54m_fck: omap_54m_fck@d40 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&dpll4_m3x2_ck>, <&sys_altclk>; + ti,bit-shift = <5>; + reg = <0x0d40>; + }; + + cm_96m_d2_fck: cm_96m_d2_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&cm_96m_fck>; + clock-mult = <1>; + clock-div = <2>; + }; + + omap_48m_fck: omap_48m_fck@d40 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&cm_96m_d2_fck>, <&sys_altclk>; + ti,bit-shift = <3>; + reg = <0x0d40>; + }; + + omap_12m_fck: omap_12m_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_48m_fck>; + clock-mult = <1>; + clock-div = <4>; + }; + + dpll4_m4_ck: dpll4_m4_ck@e40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll4_ck>; + ti,max-div = <32>; + reg = <0x0e40>; + ti,index-starts-at-one; + }; + + dpll4_m4x2_mul_ck: dpll4_m4x2_mul_ck { + #clock-cells = <0>; + compatible = "ti,fixed-factor-clock"; + clocks = <&dpll4_m4_ck>; + ti,clock-mult = <2>; + ti,clock-div = <1>; + ti,set-rate-parent; + }; + + dpll4_m4x2_ck: dpll4_m4x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll4_m4x2_mul_ck>; + ti,bit-shift = <0x1d>; + reg = <0x0d00>; + ti,set-bit-to-disable; + ti,set-rate-parent; + }; + + dpll4_m5_ck: dpll4_m5_ck@f40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll4_ck>; + ti,max-div = <63>; + reg = <0x0f40>; + ti,index-starts-at-one; + }; + + dpll4_m5x2_mul_ck: dpll4_m5x2_mul_ck { + #clock-cells = <0>; + compatible = "ti,fixed-factor-clock"; + clocks = <&dpll4_m5_ck>; + ti,clock-mult = <2>; + ti,clock-div = <1>; + ti,set-rate-parent; + }; + + dpll4_m5x2_ck: dpll4_m5x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll4_m5x2_mul_ck>; + ti,bit-shift = <0x1e>; + reg = <0x0d00>; + ti,set-bit-to-disable; + ti,set-rate-parent; + }; + + dpll4_m6_ck: dpll4_m6_ck@1140 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll4_ck>; + ti,bit-shift = <24>; + ti,max-div = <63>; + reg = <0x1140>; + ti,index-starts-at-one; + }; + + dpll4_m6x2_mul_ck: dpll4_m6x2_mul_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll4_m6_ck>; + clock-mult = <2>; + clock-div = <1>; + }; + + dpll4_m6x2_ck: dpll4_m6x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll4_m6x2_mul_ck>; + ti,bit-shift = <0x1f>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + emu_per_alwon_ck: emu_per_alwon_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll4_m6x2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + clkout2_src_gate_ck: clkout2_src_gate_ck@d70 { + #clock-cells = <0>; + compatible = "ti,composite-no-wait-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <7>; + reg = <0x0d70>; + }; + + clkout2_src_mux_ck: clkout2_src_mux_ck@d70 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_ck>, <&sys_ck>, <&cm_96m_fck>, <&omap_54m_fck>; + reg = <0x0d70>; + }; + + clkout2_src_ck: clkout2_src_ck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&clkout2_src_gate_ck>, <&clkout2_src_mux_ck>; + }; + + sys_clkout2: sys_clkout2@d70 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&clkout2_src_ck>; + ti,bit-shift = <3>; + ti,max-div = <64>; + reg = <0x0d70>; + ti,index-power-of-two; + }; + + mpu_ck: mpu_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll1_x2m2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + arm_fck: arm_fck@924 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&mpu_ck>; + reg = <0x0924>; + ti,max-div = <2>; + }; + + emu_mpu_alwon_ck: emu_mpu_alwon_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&mpu_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + l3_ick: l3_ick@a40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&core_ck>; + ti,max-div = <3>; + reg = <0x0a40>; + ti,index-starts-at-one; + }; + + l4_ick: l4_ick@a40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&l3_ick>; + ti,bit-shift = <2>; + ti,max-div = <3>; + reg = <0x0a40>; + ti,index-starts-at-one; + }; + + rm_ick: rm_ick@c40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&l4_ick>; + ti,bit-shift = <1>; + ti,max-div = <3>; + reg = <0x0c40>; + ti,index-starts-at-one; + }; + + gpt10_gate_fck: gpt10_gate_fck@a00 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <11>; + reg = <0x0a00>; + }; + + gpt10_mux_fck: gpt10_mux_fck@a40 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <6>; + reg = <0x0a40>; + }; + + gpt10_fck: gpt10_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt10_gate_fck>, <&gpt10_mux_fck>; + }; + + gpt11_gate_fck: gpt11_gate_fck@a00 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <12>; + reg = <0x0a00>; + }; + + gpt11_mux_fck: gpt11_mux_fck@a40 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <7>; + reg = <0x0a40>; + }; + + gpt11_fck: gpt11_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt11_gate_fck>, <&gpt11_mux_fck>; + }; + + core_96m_fck: core_96m_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_96m_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + mmchs2_fck: mmchs2_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <25>; + }; + + mmchs1_fck: mmchs1_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <24>; + }; + + i2c3_fck: i2c3_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <17>; + }; + + i2c2_fck: i2c2_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <16>; + }; + + i2c1_fck: i2c1_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <15>; + }; + + mcbsp5_gate_fck: mcbsp5_gate_fck@a00 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&mcbsp_clks>; + ti,bit-shift = <10>; + reg = <0x0a00>; + }; + + mcbsp1_gate_fck: mcbsp1_gate_fck@a00 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&mcbsp_clks>; + ti,bit-shift = <9>; + reg = <0x0a00>; + }; + + core_48m_fck: core_48m_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_48m_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + mcspi4_fck: mcspi4_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <21>; + }; + + mcspi3_fck: mcspi3_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <20>; + }; + + mcspi2_fck: mcspi2_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <19>; + }; + + mcspi1_fck: mcspi1_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <18>; + }; + + uart2_fck: uart2_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <14>; + }; + + uart1_fck: uart1_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <13>; + }; + + core_12m_fck: core_12m_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_12m_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + hdq_fck: hdq_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_12m_fck>; + reg = <0x0a00>; + ti,bit-shift = <22>; + }; + + core_l3_ick: core_l3_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l3_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + sdrc_ick: sdrc_ick@a10 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_l3_ick>; + reg = <0x0a10>; + ti,bit-shift = <1>; + }; + + gpmc_fck: gpmc_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&core_l3_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + core_l4_ick: core_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + mmchs2_ick: mmchs2_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <25>; + }; + + mmchs1_ick: mmchs1_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <24>; + }; + + hdq_ick: hdq_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <22>; + }; + + mcspi4_ick: mcspi4_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <21>; + }; + + mcspi3_ick: mcspi3_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <20>; + }; + + mcspi2_ick: mcspi2_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <19>; + }; + + mcspi1_ick: mcspi1_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <18>; + }; + + i2c3_ick: i2c3_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <17>; + }; + + i2c2_ick: i2c2_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <16>; + }; + + i2c1_ick: i2c1_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <15>; + }; + + uart2_ick: uart2_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <14>; + }; + + uart1_ick: uart1_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <13>; + }; + + gpt11_ick: gpt11_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <12>; + }; + + gpt10_ick: gpt10_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <11>; + }; + + mcbsp5_ick: mcbsp5_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <10>; + }; + + mcbsp1_ick: mcbsp1_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <9>; + }; + + omapctrl_ick: omapctrl_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <6>; + }; + + dss_tv_fck: dss_tv_fck@e00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&omap_54m_fck>; + reg = <0x0e00>; + ti,bit-shift = <2>; + }; + + dss_96m_fck: dss_96m_fck@e00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&omap_96m_fck>; + reg = <0x0e00>; + ti,bit-shift = <2>; + }; + + dss2_alwon_fck: dss2_alwon_fck@e00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&sys_ck>; + reg = <0x0e00>; + ti,bit-shift = <1>; + }; + + dummy_ck: dummy_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + }; + + gpt1_gate_fck: gpt1_gate_fck@c00 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <0>; + reg = <0x0c00>; + }; + + gpt1_mux_fck: gpt1_mux_fck@c40 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + reg = <0x0c40>; + }; + + gpt1_fck: gpt1_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt1_gate_fck>, <&gpt1_mux_fck>; + }; + + aes2_ick: aes2_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + ti,bit-shift = <28>; + reg = <0x0a10>; + }; + + wkup_32k_fck: wkup_32k_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_32k_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + gpio1_dbck: gpio1_dbck@c00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&wkup_32k_fck>; + reg = <0x0c00>; + ti,bit-shift = <3>; + }; + + sha12_ick: sha12_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <27>; + }; + + wdt2_fck: wdt2_fck@c00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&wkup_32k_fck>; + reg = <0x0c00>; + ti,bit-shift = <5>; + }; + + wdt2_ick: wdt2_ick@c10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&wkup_l4_ick>; + reg = <0x0c10>; + ti,bit-shift = <5>; + }; + + wdt1_ick: wdt1_ick@c10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&wkup_l4_ick>; + reg = <0x0c10>; + ti,bit-shift = <4>; + }; + + gpio1_ick: gpio1_ick@c10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&wkup_l4_ick>; + reg = <0x0c10>; + ti,bit-shift = <3>; + }; + + omap_32ksync_ick: omap_32ksync_ick@c10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&wkup_l4_ick>; + reg = <0x0c10>; + ti,bit-shift = <2>; + }; + + gpt12_ick: gpt12_ick@c10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&wkup_l4_ick>; + reg = <0x0c10>; + ti,bit-shift = <1>; + }; + + gpt1_ick: gpt1_ick@c10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&wkup_l4_ick>; + reg = <0x0c10>; + ti,bit-shift = <0>; + }; + + per_96m_fck: per_96m_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_96m_alwon_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + per_48m_fck: per_48m_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_48m_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + uart3_fck: uart3_fck@1000 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&per_48m_fck>; + reg = <0x1000>; + ti,bit-shift = <11>; + }; + + gpt2_gate_fck: gpt2_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <3>; + reg = <0x1000>; + }; + + gpt2_mux_fck: gpt2_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + reg = <0x1040>; + }; + + gpt2_fck: gpt2_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt2_gate_fck>, <&gpt2_mux_fck>; + }; + + gpt3_gate_fck: gpt3_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <4>; + reg = <0x1000>; + }; + + gpt3_mux_fck: gpt3_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <1>; + reg = <0x1040>; + }; + + gpt3_fck: gpt3_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt3_gate_fck>, <&gpt3_mux_fck>; + }; + + gpt4_gate_fck: gpt4_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <5>; + reg = <0x1000>; + }; + + gpt4_mux_fck: gpt4_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <2>; + reg = <0x1040>; + }; + + gpt4_fck: gpt4_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt4_gate_fck>, <&gpt4_mux_fck>; + }; + + gpt5_gate_fck: gpt5_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <6>; + reg = <0x1000>; + }; + + gpt5_mux_fck: gpt5_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <3>; + reg = <0x1040>; + }; + + gpt5_fck: gpt5_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt5_gate_fck>, <&gpt5_mux_fck>; + }; + + gpt6_gate_fck: gpt6_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <7>; + reg = <0x1000>; + }; + + gpt6_mux_fck: gpt6_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <4>; + reg = <0x1040>; + }; + + gpt6_fck: gpt6_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt6_gate_fck>, <&gpt6_mux_fck>; + }; + + gpt7_gate_fck: gpt7_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <8>; + reg = <0x1000>; + }; + + gpt7_mux_fck: gpt7_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <5>; + reg = <0x1040>; + }; + + gpt7_fck: gpt7_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt7_gate_fck>, <&gpt7_mux_fck>; + }; + + gpt8_gate_fck: gpt8_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <9>; + reg = <0x1000>; + }; + + gpt8_mux_fck: gpt8_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <6>; + reg = <0x1040>; + }; + + gpt8_fck: gpt8_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt8_gate_fck>, <&gpt8_mux_fck>; + }; + + gpt9_gate_fck: gpt9_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <10>; + reg = <0x1000>; + }; + + gpt9_mux_fck: gpt9_mux_fck@1040 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&omap_32k_fck>, <&sys_ck>; + ti,bit-shift = <7>; + reg = <0x1040>; + }; + + gpt9_fck: gpt9_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&gpt9_gate_fck>, <&gpt9_mux_fck>; + }; + + per_32k_alwon_fck: per_32k_alwon_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_32k_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + gpio6_dbck: gpio6_dbck@1000 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&per_32k_alwon_fck>; + reg = <0x1000>; + ti,bit-shift = <17>; + }; + + gpio5_dbck: gpio5_dbck@1000 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&per_32k_alwon_fck>; + reg = <0x1000>; + ti,bit-shift = <16>; + }; + + gpio4_dbck: gpio4_dbck@1000 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&per_32k_alwon_fck>; + reg = <0x1000>; + ti,bit-shift = <15>; + }; + + gpio3_dbck: gpio3_dbck@1000 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&per_32k_alwon_fck>; + reg = <0x1000>; + ti,bit-shift = <14>; + }; + + gpio2_dbck: gpio2_dbck@1000 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&per_32k_alwon_fck>; + reg = <0x1000>; + ti,bit-shift = <13>; + }; + + wdt3_fck: wdt3_fck@1000 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&per_32k_alwon_fck>; + reg = <0x1000>; + ti,bit-shift = <12>; + }; + + per_l4_ick: per_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + gpio6_ick: gpio6_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <17>; + }; + + gpio5_ick: gpio5_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <16>; + }; + + gpio4_ick: gpio4_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <15>; + }; + + gpio3_ick: gpio3_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <14>; + }; + + gpio2_ick: gpio2_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <13>; + }; + + wdt3_ick: wdt3_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <12>; + }; + + uart3_ick: uart3_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <11>; + }; + + uart4_ick: uart4_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <18>; + }; + + gpt9_ick: gpt9_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <10>; + }; + + gpt8_ick: gpt8_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <9>; + }; + + gpt7_ick: gpt7_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <8>; + }; + + gpt6_ick: gpt6_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <7>; + }; + + gpt5_ick: gpt5_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <6>; + }; + + gpt4_ick: gpt4_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <5>; + }; + + gpt3_ick: gpt3_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <4>; + }; + + gpt2_ick: gpt2_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <3>; + }; + + mcbsp2_ick: mcbsp2_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <0>; + }; + + mcbsp3_ick: mcbsp3_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <1>; + }; + + mcbsp4_ick: mcbsp4_ick@1010 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&per_l4_ick>; + reg = <0x1010>; + ti,bit-shift = <2>; + }; + + mcbsp2_gate_fck: mcbsp2_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&mcbsp_clks>; + ti,bit-shift = <0>; + reg = <0x1000>; + }; + + mcbsp3_gate_fck: mcbsp3_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&mcbsp_clks>; + ti,bit-shift = <1>; + reg = <0x1000>; + }; + + mcbsp4_gate_fck: mcbsp4_gate_fck@1000 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&mcbsp_clks>; + ti,bit-shift = <2>; + reg = <0x1000>; + }; + + emu_src_mux_ck: emu_src_mux_ck@1140 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>; + reg = <0x1140>; + }; + + emu_src_ck: emu_src_ck { + #clock-cells = <0>; + compatible = "ti,clkdm-gate-clock"; + clocks = <&emu_src_mux_ck>; + }; + + pclk_fck: pclk_fck@1140 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&emu_src_ck>; + ti,bit-shift = <8>; + ti,max-div = <7>; + reg = <0x1140>; + ti,index-starts-at-one; + }; + + pclkx2_fck: pclkx2_fck@1140 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&emu_src_ck>; + ti,bit-shift = <6>; + ti,max-div = <3>; + reg = <0x1140>; + ti,index-starts-at-one; + }; + + atclk_fck: atclk_fck@1140 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&emu_src_ck>; + ti,bit-shift = <4>; + ti,max-div = <3>; + reg = <0x1140>; + ti,index-starts-at-one; + }; + + traceclk_src_fck: traceclk_src_fck@1140 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>; + ti,bit-shift = <2>; + reg = <0x1140>; + }; + + traceclk_fck: traceclk_fck@1140 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&traceclk_src_fck>; + ti,bit-shift = <11>; + ti,max-div = <7>; + reg = <0x1140>; + ti,index-starts-at-one; + }; + + secure_32k_fck: secure_32k_fck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + }; + + gpt12_fck: gpt12_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&secure_32k_fck>; + clock-mult = <1>; + clock-div = <1>; + }; + + wdt1_fck: wdt1_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&secure_32k_fck>; + clock-mult = <1>; + clock-div = <1>; + }; +}; + +&cm_clockdomains { + core_l3_clkdm: core_l3_clkdm { + compatible = "ti,clockdomain"; + clocks = <&sdrc_ick>; + }; + + dpll3_clkdm: dpll3_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dpll3_ck>; + }; + + dpll1_clkdm: dpll1_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dpll1_ck>; + }; + + per_clkdm: per_clkdm { + compatible = "ti,clockdomain"; + clocks = <&uart3_fck>, <&gpio6_dbck>, <&gpio5_dbck>, + <&gpio4_dbck>, <&gpio3_dbck>, <&gpio2_dbck>, + <&wdt3_fck>, <&gpio6_ick>, <&gpio5_ick>, <&gpio4_ick>, + <&gpio3_ick>, <&gpio2_ick>, <&wdt3_ick>, <&uart3_ick>, + <&uart4_ick>, <&gpt9_ick>, <&gpt8_ick>, <&gpt7_ick>, + <&gpt6_ick>, <&gpt5_ick>, <&gpt4_ick>, <&gpt3_ick>, + <&gpt2_ick>, <&mcbsp2_ick>, <&mcbsp3_ick>, + <&mcbsp4_ick>; + }; + + emu_clkdm: emu_clkdm { + compatible = "ti,clockdomain"; + clocks = <&emu_src_ck>; + }; + + dpll4_clkdm: dpll4_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dpll4_ck>; + }; + + wkup_clkdm: wkup_clkdm { + compatible = "ti,clockdomain"; + clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>, + <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>, + <&gpt1_ick>; + }; + + dss_clkdm: dss_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dss_tv_fck>, <&dss_96m_fck>, <&dss2_alwon_fck>; + }; + + core_l4_clkdm: core_l4_clkdm { + compatible = "ti,clockdomain"; + clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>, + <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>, + <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>, + <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>, + <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>, + <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>, + <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, + <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, + <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>; + }; +};
On Mon, Apr 17, 2017 at 08:09:38AM -0500, Adam Ford wrote:
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/omap3.dtsi b/arch/arm/dts/omap3.dtsi new file mode 100644 index 0000000..a0f2412
Applied to u-boot/master, thanks!
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards. DM3730 can use this same device tree.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/omap34xx-omap36xx-clocks.dtsi b/arch/arm/dts/omap34xx-omap36xx-clocks.dtsi new file mode 100644 index 0000000..db47f12 --- /dev/null +++ b/arch/arm/dts/omap34xx-omap36xx-clocks.dtsi @@ -0,0 +1,268 @@ +/* + * Device Tree Source for OMAP34XX/OMAP36XX clock data + * + * Copyright (C) 2013 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +&cm_clocks { + security_l4_ick2: security_l4_ick2 { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + aes1_ick: aes1_ick@a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + ti,bit-shift = <3>; + reg = <0x0a14>; + }; + + rng_ick: rng_ick@a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x0a14>; + ti,bit-shift = <2>; + }; + + sha11_ick: sha11_ick@a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x0a14>; + ti,bit-shift = <1>; + }; + + des1_ick: des1_ick@a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x0a14>; + ti,bit-shift = <0>; + }; + + cam_mclk: cam_mclk@f00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll4_m5x2_ck>; + ti,bit-shift = <0>; + reg = <0x0f00>; + ti,set-rate-parent; + }; + + cam_ick: cam_ick@f10 { + #clock-cells = <0>; + compatible = "ti,omap3-no-wait-interface-clock"; + clocks = <&l4_ick>; + reg = <0x0f10>; + ti,bit-shift = <0>; + }; + + csi2_96m_fck: csi2_96m_fck@f00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0f00>; + ti,bit-shift = <1>; + }; + + security_l3_ick: security_l3_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l3_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + pka_ick: pka_ick@a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l3_ick>; + reg = <0x0a14>; + ti,bit-shift = <4>; + }; + + icr_ick: icr_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <29>; + }; + + des2_ick: des2_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <26>; + }; + + mspro_ick: mspro_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <23>; + }; + + mailboxes_ick: mailboxes_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <7>; + }; + + ssi_l4_ick: ssi_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + sr1_fck: sr1_fck@c00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&sys_ck>; + reg = <0x0c00>; + ti,bit-shift = <6>; + }; + + sr2_fck: sr2_fck@c00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&sys_ck>; + reg = <0x0c00>; + ti,bit-shift = <7>; + }; + + sr_l4_ick: sr_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + dpll2_fck: dpll2_fck@40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&core_ck>; + ti,bit-shift = <19>; + ti,max-div = <7>; + reg = <0x0040>; + ti,index-starts-at-one; + }; + + dpll2_ck: dpll2_ck@4 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-clock"; + clocks = <&sys_ck>, <&dpll2_fck>; + reg = <0x0004>, <0x0024>, <0x0040>, <0x0034>; + ti,low-power-stop; + ti,lock; + ti,low-power-bypass; + }; + + dpll2_m2_ck: dpll2_m2_ck@44 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll2_ck>; + ti,max-div = <31>; + reg = <0x0044>; + ti,index-starts-at-one; + }; + + iva2_ck: iva2_ck@0 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&dpll2_m2_ck>; + reg = <0x0000>; + ti,bit-shift = <0>; + }; + + modem_fck: modem_fck@a00 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&sys_ck>; + reg = <0x0a00>; + ti,bit-shift = <31>; + }; + + sad2d_ick: sad2d_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&l3_ick>; + reg = <0x0a10>; + ti,bit-shift = <3>; + }; + + mad2d_ick: mad2d_ick@a18 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&l3_ick>; + reg = <0x0a18>; + ti,bit-shift = <3>; + }; + + mspro_fck: mspro_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <23>; + }; +}; + +&cm_clockdomains { + cam_clkdm: cam_clkdm { + compatible = "ti,clockdomain"; + clocks = <&cam_ick>, <&csi2_96m_fck>; + }; + + iva2_clkdm: iva2_clkdm { + compatible = "ti,clockdomain"; + clocks = <&iva2_ck>; + }; + + dpll2_clkdm: dpll2_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dpll2_ck>; + }; + + wkup_clkdm: wkup_clkdm { + compatible = "ti,clockdomain"; + clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>, + <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>, + <&gpt1_ick>, <&sr1_fck>, <&sr2_fck>; + }; + + d2d_clkdm: d2d_clkdm { + compatible = "ti,clockdomain"; + clocks = <&modem_fck>, <&sad2d_ick>, <&mad2d_ick>; + }; + + core_l4_clkdm: core_l4_clkdm { + compatible = "ti,clockdomain"; + clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>, + <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>, + <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>, + <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>, + <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>, + <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>, + <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, + <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, + <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&icr_ick>, + <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>, + <&mspro_fck>; + }; +}; diff --git a/arch/arm/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi b/arch/arm/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi new file mode 100644 index 0000000..572cb53 --- /dev/null +++ b/arch/arm/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi @@ -0,0 +1,242 @@ +/* + * Device Tree Source for OMAP36xx/AM35xx/OMAP34xx clock data + * + * Copyright (C) 2013 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +&prm_clocks { + corex2_d3_fck: corex2_d3_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&corex2_fck>; + clock-mult = <1>; + clock-div = <3>; + }; + + corex2_d5_fck: corex2_d5_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&corex2_fck>; + clock-mult = <1>; + clock-div = <5>; + }; +}; +&cm_clocks { + dpll5_ck: dpll5_ck@d04 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0d04>, <0x0d24>, <0x0d4c>, <0x0d34>; + ti,low-power-stop; + ti,lock; + }; + + dpll5_m2_ck: dpll5_m2_ck@d50 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll5_ck>; + ti,max-div = <31>; + reg = <0x0d50>; + ti,index-starts-at-one; + }; + + sgx_gate_fck: sgx_gate_fck@b00 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <1>; + reg = <0x0b00>; + }; + + core_d3_ck: core_d3_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&core_ck>; + clock-mult = <1>; + clock-div = <3>; + }; + + core_d4_ck: core_d4_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&core_ck>; + clock-mult = <1>; + clock-div = <4>; + }; + + core_d6_ck: core_d6_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&core_ck>; + clock-mult = <1>; + clock-div = <6>; + }; + + omap_192m_alwon_fck: omap_192m_alwon_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll4_m2x2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + core_d2_ck: core_d2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&core_ck>; + clock-mult = <1>; + clock-div = <2>; + }; + + sgx_mux_fck: sgx_mux_fck@b40 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_d3_ck>, <&core_d4_ck>, <&core_d6_ck>, <&cm_96m_fck>, <&omap_192m_alwon_fck>, <&core_d2_ck>, <&corex2_d3_fck>, <&corex2_d5_fck>; + reg = <0x0b40>; + }; + + sgx_fck: sgx_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&sgx_gate_fck>, <&sgx_mux_fck>; + }; + + sgx_ick: sgx_ick@b10 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&l3_ick>; + reg = <0x0b10>; + ti,bit-shift = <0>; + }; + + cpefuse_fck: cpefuse_fck@a08 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&sys_ck>; + reg = <0x0a08>; + ti,bit-shift = <0>; + }; + + ts_fck: ts_fck@a08 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&omap_32k_fck>; + reg = <0x0a08>; + ti,bit-shift = <1>; + }; + + usbtll_fck: usbtll_fck@a08 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&dpll5_m2_ck>; + reg = <0x0a08>; + ti,bit-shift = <2>; + }; + + usbtll_ick: usbtll_ick@a18 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a18>; + ti,bit-shift = <2>; + }; + + mmchs3_ick: mmchs3_ick@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <30>; + }; + + mmchs3_fck: mmchs3_fck@a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <30>; + }; + + dss1_alwon_fck: dss1_alwon_fck_3430es2@e00 { + #clock-cells = <0>; + compatible = "ti,dss-gate-clock"; + clocks = <&dpll4_m4x2_ck>; + ti,bit-shift = <0>; + reg = <0x0e00>; + ti,set-rate-parent; + }; + + dss_ick: dss_ick_3430es2@e10 { + #clock-cells = <0>; + compatible = "ti,omap3-dss-interface-clock"; + clocks = <&l4_ick>; + reg = <0x0e10>; + ti,bit-shift = <0>; + }; + + usbhost_120m_fck: usbhost_120m_fck@1400 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll5_m2_ck>; + reg = <0x1400>; + ti,bit-shift = <1>; + }; + + usbhost_48m_fck: usbhost_48m_fck@1400 { + #clock-cells = <0>; + compatible = "ti,dss-gate-clock"; + clocks = <&omap_48m_fck>; + reg = <0x1400>; + ti,bit-shift = <0>; + }; + + usbhost_ick: usbhost_ick@1410 { + #clock-cells = <0>; + compatible = "ti,omap3-dss-interface-clock"; + clocks = <&l4_ick>; + reg = <0x1410>; + ti,bit-shift = <0>; + }; +}; + +&cm_clockdomains { + dpll5_clkdm: dpll5_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dpll5_ck>; + }; + + sgx_clkdm: sgx_clkdm { + compatible = "ti,clockdomain"; + clocks = <&sgx_ick>; + }; + + dss_clkdm: dss_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dss_tv_fck>, <&dss_96m_fck>, <&dss2_alwon_fck>, + <&dss1_alwon_fck>, <&dss_ick>; + }; + + core_l4_clkdm: core_l4_clkdm { + compatible = "ti,clockdomain"; + clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>, + <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>, + <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>, + <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>, + <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>, + <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>, + <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, + <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, + <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, + <&cpefuse_fck>, <&ts_fck>, <&usbtll_fck>, + <&usbtll_ick>, <&mmchs3_ick>, <&mmchs3_fck>; + }; + + usbhost_clkdm: usbhost_clkdm { + compatible = "ti,clockdomain"; + clocks = <&usbhost_120m_fck>, <&usbhost_48m_fck>, + <&usbhost_ick>; + }; +}; diff --git a/arch/arm/dts/omap36xx-clocks.dtsi b/arch/arm/dts/omap36xx-clocks.dtsi new file mode 100644 index 0000000..9c7ed03 --- /dev/null +++ b/arch/arm/dts/omap36xx-clocks.dtsi @@ -0,0 +1,110 @@ +/* + * Device Tree Source for OMAP36xx clock data + * + * Copyright (C) 2013 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +&cm_clocks { + dpll4_ck: dpll4_ck@d00 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-per-j-type-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0d00>, <0x0d20>, <0x0d44>, <0x0d30>; + }; + + dpll4_m5x2_ck: dpll4_m5x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,hsdiv-gate-clock"; + clocks = <&dpll4_m5x2_mul_ck>; + ti,bit-shift = <0x1e>; + reg = <0x0d00>; + ti,set-rate-parent; + ti,set-bit-to-disable; + }; + + dpll4_m2x2_ck: dpll4_m2x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,hsdiv-gate-clock"; + clocks = <&dpll4_m2x2_mul_ck>; + ti,bit-shift = <0x1b>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + dpll3_m3x2_ck: dpll3_m3x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,hsdiv-gate-clock"; + clocks = <&dpll3_m3x2_mul_ck>; + ti,bit-shift = <0xc>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + dpll4_m3x2_ck: dpll4_m3x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,hsdiv-gate-clock"; + clocks = <&dpll4_m3x2_mul_ck>; + ti,bit-shift = <0x1c>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + dpll4_m6x2_ck: dpll4_m6x2_ck@d00 { + #clock-cells = <0>; + compatible = "ti,hsdiv-gate-clock"; + clocks = <&dpll4_m6x2_mul_ck>; + ti,bit-shift = <0x1f>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + uart4_fck: uart4_fck@1000 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&per_48m_fck>; + reg = <0x1000>; + ti,bit-shift = <18>; + }; +}; + +&dpll4_m2x2_mul_ck { + clock-mult = <1>; +}; + +&dpll4_m3x2_mul_ck { + clock-mult = <1>; +}; + +&dpll4_m4x2_mul_ck { + ti,clock-mult = <1>; +}; + +&dpll4_m5x2_mul_ck { + ti,clock-mult = <1>; +}; + +&dpll4_m6x2_mul_ck { + clock-mult = <1>; +}; + +&cm_clockdomains { + dpll4_clkdm: dpll4_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dpll4_ck>; + }; + + per_clkdm: per_clkdm { + compatible = "ti,clockdomain"; + clocks = <&uart3_fck>, <&gpio6_dbck>, <&gpio5_dbck>, + <&gpio4_dbck>, <&gpio3_dbck>, <&gpio2_dbck>, + <&wdt3_fck>, <&gpio6_ick>, <&gpio5_ick>, <&gpio4_ick>, + <&gpio3_ick>, <&gpio2_ick>, <&wdt3_ick>, <&uart3_ick>, + <&uart4_ick>, <&gpt9_ick>, <&gpt8_ick>, <&gpt7_ick>, + <&gpt6_ick>, <&gpt5_ick>, <&gpt4_ick>, <&gpt3_ick>, + <&gpt2_ick>, <&mcbsp2_ick>, <&mcbsp3_ick>, + <&mcbsp4_ick>, <&uart4_fck>; + }; +}; diff --git a/arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi b/arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi new file mode 100644 index 0000000..a9eec1b --- /dev/null +++ b/arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi @@ -0,0 +1,198 @@ +/* + * Device Tree Source for OMAP34xx/OMAP36xx clock data + * + * Copyright (C) 2013 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +&cm_clocks { + ssi_ssr_gate_fck_3430es2: ssi_ssr_gate_fck_3430es2@a00 { + #clock-cells = <0>; + compatible = "ti,composite-no-wait-gate-clock"; + clocks = <&corex2_fck>; + ti,bit-shift = <0>; + reg = <0x0a00>; + }; + + ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2@a40 { + #clock-cells = <0>; + compatible = "ti,composite-divider-clock"; + clocks = <&corex2_fck>; + ti,bit-shift = <8>; + reg = <0x0a40>; + ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>; + }; + + ssi_ssr_fck: ssi_ssr_fck_3430es2 { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&ssi_ssr_gate_fck_3430es2>, <&ssi_ssr_div_fck_3430es2>; + }; + + ssi_sst_fck: ssi_sst_fck_3430es2 { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&ssi_ssr_fck>; + clock-mult = <1>; + clock-div = <2>; + }; + + hsotgusb_ick_3430es2: hsotgusb_ick_3430es2@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-hsotgusb-interface-clock"; + clocks = <&core_l3_ick>; + reg = <0x0a10>; + ti,bit-shift = <4>; + }; + + ssi_l4_ick: ssi_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + ssi_ick: ssi_ick_3430es2@a10 { + #clock-cells = <0>; + compatible = "ti,omap3-ssi-interface-clock"; + clocks = <&ssi_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <0>; + }; + + usim_gate_fck: usim_gate_fck@c00 { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&omap_96m_fck>; + ti,bit-shift = <9>; + reg = <0x0c00>; + }; + + sys_d2_ck: sys_d2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_ck>; + clock-mult = <1>; + clock-div = <2>; + }; + + omap_96m_d2_fck: omap_96m_d2_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_96m_fck>; + clock-mult = <1>; + clock-div = <2>; + }; + + omap_96m_d4_fck: omap_96m_d4_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_96m_fck>; + clock-mult = <1>; + clock-div = <4>; + }; + + omap_96m_d8_fck: omap_96m_d8_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_96m_fck>; + clock-mult = <1>; + clock-div = <8>; + }; + + omap_96m_d10_fck: omap_96m_d10_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&omap_96m_fck>; + clock-mult = <1>; + clock-div = <10>; + }; + + dpll5_m2_d4_ck: dpll5_m2_d4_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll5_m2_ck>; + clock-mult = <1>; + clock-div = <4>; + }; + + dpll5_m2_d8_ck: dpll5_m2_d8_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll5_m2_ck>; + clock-mult = <1>; + clock-div = <8>; + }; + + dpll5_m2_d16_ck: dpll5_m2_d16_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll5_m2_ck>; + clock-mult = <1>; + clock-div = <16>; + }; + + dpll5_m2_d20_ck: dpll5_m2_d20_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll5_m2_ck>; + clock-mult = <1>; + clock-div = <20>; + }; + + usim_mux_fck: usim_mux_fck@c40 { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&sys_ck>, <&sys_d2_ck>, <&omap_96m_d2_fck>, <&omap_96m_d4_fck>, <&omap_96m_d8_fck>, <&omap_96m_d10_fck>, <&dpll5_m2_d4_ck>, <&dpll5_m2_d8_ck>, <&dpll5_m2_d16_ck>, <&dpll5_m2_d20_ck>; + ti,bit-shift = <3>; + reg = <0x0c40>; + ti,index-starts-at-one; + }; + + usim_fck: usim_fck { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&usim_gate_fck>, <&usim_mux_fck>; + }; + + usim_ick: usim_ick@c10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&wkup_l4_ick>; + reg = <0x0c10>; + ti,bit-shift = <9>; + }; +}; + +&cm_clockdomains { + core_l3_clkdm: core_l3_clkdm { + compatible = "ti,clockdomain"; + clocks = <&sdrc_ick>, <&hsotgusb_ick_3430es2>; + }; + + wkup_clkdm: wkup_clkdm { + compatible = "ti,clockdomain"; + clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>, + <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>, + <&gpt1_ick>, <&usim_ick>; + }; + + core_l4_clkdm: core_l4_clkdm { + compatible = "ti,clockdomain"; + clocks = <&cpefuse_fck>, <&ts_fck>, <&usbtll_fck>, + <&usbtll_ick>, <&mmchs3_ick>, <&mmchs3_fck>, + <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>, + <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>, + <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>, + <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>, + <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>, + <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>, + <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, + <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, + <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, + <&ssi_ick>; + }; +}; diff --git a/arch/arm/dts/omap36xx.dtsi b/arch/arm/dts/omap36xx.dtsi new file mode 100644 index 0000000..fc22f0d --- /dev/null +++ b/arch/arm/dts/omap36xx.dtsi @@ -0,0 +1,118 @@ +/* + * Device Tree Source for OMAP3 SoC + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <dt-bindings/media/omap3-isp.h> + +#include "omap3.dtsi" + +/ { + aliases { + serial3 = &uart4; + }; + + cpus { + /* OMAP3630/OMAP37xx 'standard device' variants OPP50 to OPP130 */ + cpu@0 { + operating-points = < + /* kHz uV */ + 300000 1012500 + 600000 1200000 + 800000 1325000 + >; + clock-latency = <300000>; /* From legacy driver */ + }; + }; + + ocp@68000000 { + uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + dmas = <&sdma 81 &sdma 82>; + dma-names = "tx", "rx"; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + }; + + abb_mpu_iva: regulator-abb-mpu { + compatible = "ti,abb-v1"; + regulator-name = "abb_mpu_iva"; + #address-cells = <0>; + #size-cells = <0>; + reg = <0x483072f0 0x8>, <0x48306818 0x4>; + reg-names = "base-address", "int-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sys_ck>; + ti,settling-time = <30>; + ti,clock-cycles = <8>; + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1012500 0 0 0 0 0 + 1200000 0 0 0 0 0 + 1325000 0 0 0 0 0 + 1375000 1 0 0 0 0 + >; + }; + + omap3_pmx_core2: pinmux@480025a0 { + compatible = "ti,omap3-padconf", "pinctrl-single"; + reg = <0x480025a0 0x5c>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + + isp: isp@480bc000 { + compatible = "ti,omap3-isp"; + reg = <0x480bc000 0x12fc + 0x480bd800 0x0600>; + interrupts = <24>; + iommus = <&mmu_isp>; + syscon = <&scm_conf 0x2f0>; + ti,phy-type = <OMAP3ISP_PHY_TYPE_CSIPHY>; + #clock-cells = <1>; + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + bandgap@48002524 { + reg = <0x48002524 0x4>; + compatible = "ti,omap36xx-bandgap"; + #thermal-sensor-cells = <0>; + }; + }; +}; + +/* OMAP3630 needs dss_96m_fck for VENC */ +&venc { + clocks = <&dss_tv_fck>, <&dss_96m_fck>; + clock-names = "fck", "tv_dac_clk"; +}; + +&ssi { + status = "ok"; + + clocks = <&ssi_ssr_fck>, + <&ssi_sst_fck>, + <&ssi_ick>; + clock-names = "ssi_ssr_fck", + "ssi_sst_fck", + "ssi_ick"; +}; + +/include/ "omap34xx-omap36xx-clocks.dtsi" +/include/ "omap36xx-omap3430es2plus-clocks.dtsi" +/include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi" +/include/ "omap36xx-clocks.dtsi" diff --git a/include/dt-bindings/media/omap3-isp.h b/include/dt-bindings/media/omap3-isp.h new file mode 100644 index 0000000..4e42084 --- /dev/null +++ b/include/dt-bindings/media/omap3-isp.h @@ -0,0 +1,22 @@ +/* + * include/dt-bindings/media/omap3-isp.h + * + * Copyright (C) 2015 Sakari Ailus + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + */ + +#ifndef __DT_BINDINGS_OMAP3_ISP_H__ +#define __DT_BINDINGS_OMAP3_ISP_H__ + +#define OMAP3ISP_PHY_TYPE_COMPLEX_IO 0 +#define OMAP3ISP_PHY_TYPE_CSIPHY 1 + +#endif /* __DT_BINDINGS_OMAP3_ISP_H__ */
On Mon, Apr 17, 2017 at 08:09:39AM -0500, Adam Ford wrote:
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards. DM3730 can use this same device tree.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/omap34xx-omap36xx-clocks.dtsi b/arch/arm/dts/omap34xx-omap36xx-clocks.dtsi new file mode 100644 index 0000000..db47f12
Applied to u-boot/master, thanks!
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4 (4430/60/70), OMAP5 (5430) and AM335X (3359) were added in 960187ffa125( "ARM: OMAP: I2C: New read, write and probe functions") but not tested on OMAP3. This patch will allow the updated drivers using device tree and DM_I2C to operate on OMAP3.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c index 26996e9..a23737a 100644 --- a/drivers/i2c/omap24xx_i2c.c +++ b/drivers/i2c/omap24xx_i2c.c @@ -910,6 +910,7 @@ static const struct dm_i2c_ops omap_i2c_ops = { };
static const struct udevice_id omap_i2c_ids[] = { + { .compatible = "ti,omap3-i2c" }, { .compatible = "ti,omap4-i2c" }, { } };
On Mon, Apr 17, 2017 at 08:09:40AM -0500, Adam Ford wrote:
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4 (4430/60/70), OMAP5 (5430) and AM335X (3359) were added in 960187ffa125( "ARM: OMAP: I2C: New read, write and probe functions") but not tested on OMAP3. This patch will allow the updated drivers using device tree and DM_I2C to operate on OMAP3.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c index 26996e9..a23737a 100644
Applied to u-boot/master, thanks!
Many OMAP3 boards use a TWL4030 PMIC. This brings in the related device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/twl4030.dtsi b/arch/arm/dts/twl4030.dtsi new file mode 100644 index 0000000..6cb0a01 --- /dev/null +++ b/arch/arm/dts/twl4030.dtsi @@ -0,0 +1,161 @@ +/* + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Integrated Power Management Chip + */ +&twl { + compatible = "ti,twl4030"; + interrupt-controller; + #interrupt-cells = <1>; + + rtc { + compatible = "ti,twl4030-rtc"; + interrupts = <11>; + }; + + charger: bci { + compatible = "ti,twl4030-bci"; + interrupts = <9>, <2>; + bci3v1-supply = <&vusb3v1>; + }; + + watchdog { + compatible = "ti,twl4030-wdt"; + }; + + vaux1: regulator-vaux1 { + compatible = "ti,twl4030-vaux1"; + }; + + vaux2: regulator-vaux2 { + compatible = "ti,twl4030-vaux2"; + }; + + vaux3: regulator-vaux3 { + compatible = "ti,twl4030-vaux3"; + }; + + vaux4: regulator-vaux4 { + compatible = "ti,twl4030-vaux4"; + }; + + vcc: regulator-vdd1 { + compatible = "ti,twl4030-vdd1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1450000>; + }; + + vdac: regulator-vdac { + compatible = "ti,twl4030-vdac"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vio: regulator-vio { + compatible = "ti,twl4030-vio"; + }; + + vintana1: regulator-vintana1 { + compatible = "ti,twl4030-vintana1"; + }; + + vintana2: regulator-vintana2 { + compatible = "ti,twl4030-vintana2"; + }; + + vintdig: regulator-vintdig { + compatible = "ti,twl4030-vintdig"; + }; + + vmmc1: regulator-vmmc1 { + compatible = "ti,twl4030-vmmc1"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; + }; + + vmmc2: regulator-vmmc2 { + compatible = "ti,twl4030-vmmc2"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; + }; + + vusb1v5: regulator-vusb1v5 { + compatible = "ti,twl4030-vusb1v5"; + }; + + vusb1v8: regulator-vusb1v8 { + compatible = "ti,twl4030-vusb1v8"; + }; + + vusb3v1: regulator-vusb3v1 { + compatible = "ti,twl4030-vusb3v1"; + }; + + vpll1: regulator-vpll1 { + compatible = "ti,twl4030-vpll1"; + }; + + vpll2: regulator-vpll2 { + compatible = "ti,twl4030-vpll2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vsim: regulator-vsim { + compatible = "ti,twl4030-vsim"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + + twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + usb2_phy: twl4030-usb { + compatible = "ti,twl4030-usb"; + interrupts = <10>, <4>; + usb1v5-supply = <&vusb1v5>; + usb1v8-supply = <&vusb1v8>; + usb3v1-supply = <&vusb3v1>; + usb_mode = <1>; + #phy-cells = <0>; + }; + + twl_pwm: pwm { + compatible = "ti,twl4030-pwm"; + #pwm-cells = <2>; + }; + + twl_pwmled: pwmled { + compatible = "ti,twl4030-pwmled"; + #pwm-cells = <2>; + }; + + twl_pwrbutton: pwrbutton { + compatible = "ti,twl4030-pwrbutton"; + interrupts = <8>; + }; + + twl_keypad: keypad { + compatible = "ti,twl4030-keypad"; + interrupts = <1>; + keypad,num-rows = <8>; + keypad,num-columns = <8>; + }; + + twl_madc: madc { + compatible = "ti,twl4030-madc"; + interrupts = <3>; + #io-channel-cells = <1>; + }; +}; diff --git a/arch/arm/dts/twl4030_omap3.dtsi b/arch/arm/dts/twl4030_omap3.dtsi new file mode 100644 index 0000000..f9aaa53 --- /dev/null +++ b/arch/arm/dts/twl4030_omap3.dtsi @@ -0,0 +1,42 @@ +/* + * Copyright (C) 2013 Linaro, Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&twl { + pinctrl-names = "default"; + pinctrl-0 = <&twl4030_pins &twl4030_vpins>; +}; + +&omap3_pmx_core { + /* + * On most OMAP3 platforms, the twl4030 IRQ line is connected + * to the SYS_NIRQ line on OMAP. Therefore, configure the + * defaults for the SYS_NIRQ pin here. + */ + twl4030_pins: pinmux_twl4030_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21e0, PIN_INPUT_PULLUP | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* sys_nirq.sys_nirq */ + >; + }; +}; + +/* + * If your board is not using the I2C4 pins with twl4030, then don't include + * this file. For proper idle mode signaling with sys_clkreq and sys_off_mode + * pins we need to configure I2C4, or else use the legacy sys_nvmode1 and + * sys_nvmode2 signaling. + */ +&omap3_pmx_wkup { + twl4030_vpins: pinmux_twl4030_vpins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a00, PIN_INPUT | MUX_MODE0) /* i2c4_scl.i2c4_scl */ + OMAP3_WKUP_IOPAD(0x2a02, PIN_INPUT | MUX_MODE0) /* i2c4_sda.i2c4_sda */ + OMAP3_WKUP_IOPAD(0x2a06, PIN_OUTPUT | MUX_MODE0) /* sys_clkreq.sys_clkreq */ + OMAP3_WKUP_IOPAD(0x2a18, PIN_OUTPUT | MUX_MODE0) /* sys_off_mode.sys_off_mode */ + >; + }; +};
On Mon, Apr 17, 2017 at 08:09:41AM -0500, Adam Ford wrote:
Many OMAP3 boards use a TWL4030 PMIC. This brings in the related device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/twl4030.dtsi b/arch/arm/dts/twl4030.dtsi new file mode 100644 index 0000000..6cb0a01
Applied to u-boot/master, thanks!
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus. This copies this device tree from Linux 4.9.y stable
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/omap-gpmc-smsc9221.dtsi b/arch/arm/dts/omap-gpmc-smsc9221.dtsi new file mode 100644 index 0000000..73e272f --- /dev/null +++ b/arch/arm/dts/omap-gpmc-smsc9221.dtsi @@ -0,0 +1,58 @@ +/* + * Common file for GPMC connected smsc9221 on omaps + * + * Compared to smsc911x, smsc9221 (and others like smsc9217 + * or smsc 9218) has faster timings, leading to higher + * bandwidth. + * + * Note that the board specifc DTS file needs to specify + * ranges, pinctrl, reg, interrupt parent and interrupts. + */ + +/ { + vddvario: regulator-vddvario { + compatible = "regulator-fixed"; + regulator-name = "vddvario"; + regulator-always-on; + }; + + vdd33a: regulator-vdd33a { + compatible = "regulator-fixed"; + regulator-name = "vdd33a"; + regulator-always-on; + }; +}; + +&gpmc { + ethernet@gpmc { + compatible = "smsc,lan9221","smsc,lan9115"; + bank-width = <2>; + + gpmc,mux-add-data; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <42>; + gpmc,cs-wr-off-ns = <36>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <12>; + gpmc,adv-wr-off-ns = <12>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <42>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <36>; + gpmc,rd-cycle-ns = <60>; + gpmc,wr-cycle-ns = <54>; + gpmc,access-ns = <36>; + gpmc,page-burst-access-ns = <0>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,wr-data-mux-bus-ns = <18>; + gpmc,wr-access-ns = <42>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + + vddvario-supply = <&vddvario>; + vdd33a-supply = <&vdd33a>; + reg-io-width = <4>; + smsc,save-mac-address; + }; +};
On Mon, Apr 17, 2017 at 08:09:42AM -0500, Adam Ford wrote:
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus. This copies this device tree from Linux 4.9.y stable
Signed-off-by: Adam Ford aford173@gmail.com Reviewed-by: Lokesh Vutla lokeshvutla@ti.com
diff --git a/arch/arm/dts/omap-gpmc-smsc9221.dtsi b/arch/arm/dts/omap-gpmc-smsc9221.dtsi new file mode 100644 index 0000000..73e272f
Applied to u-boot/master, thanks!
This adds the device tree. Previous commit added both boards at the same time.
Signed-off-by: Adam Ford aford173@gmail.com
Changes in V2: Split the SOM-LV from Torpedo
diff --git a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts new file mode 100644 index 0000000..1702b9e --- /dev/null +++ b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts @@ -0,0 +1,269 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap36xx.dtsi" +#include "logicpd-som-lv.dtsi" +#include "omap-gpmc-smsc9221.dtsi" + +/ { + model = "LogicPD Zoom DM3730 SOM-LV Development Kit"; + compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3"; + + chosen { + stdout-path = &uart1; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins>; + + sysboot2 { + label = "gpio3"; + gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* gpio_111 / uP_GPIO_3 */ + linux,code = <BTN_0>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &led_pins_wkup>; + + led1 { + label = "led1"; + gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* gpio133 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* gpio11 */ + linux,default-trigger = "none"; + }; + }; +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <1 0 0x08000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + + ethernet@gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; /* gpio_152 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + lcd0: display@0 { + compatible = "panel-dpi"; + label = "28"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + pinctrl-0 = <&lcd_enable_pin>; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <2>; + vsync-len = <11>; + hsync-active = <1>; + vsync-active = <1>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&twl_pwm 0 5000000>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&mmc2 { + status = "disabled"; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4) /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 */ + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */ + >; + }; + + lcd_enable_pin: pinmux_lcd_enable_pin { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + >; + }; +}; + +&omap3_pmx_wkup { + led_pins_wkup: pinmux_led_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* sys_boot6.gpio_8 */ + >; + }; +}; + + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi new file mode 100644 index 0000000..46dae55 --- /dev/null +++ b/arch/arm/dts/logicpd-som-lv.dtsi @@ -0,0 +1,271 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/input/input.h> + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0>; + }; + + wl12xx_vmmc: wl12xx_vmmc { + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 3 0>; /* gpio_3 */ + startup-delay-us = <70000>; + enable-active-high; + vin-supply = <&vmmc2>; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */ + }; +}; + +&gpmc { + ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */ + + nand@0,0 { + compatible = "ti,omap2-nand"; + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ + <1 IRQ_TYPE_NONE>; /* termcount */ + linux,mtd-name = "micron,mt29f4g16abbda3w"; + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + gpmc,device-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + + /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */ + + x-loader@0 { + label = "x-loader"; + reg = <0 0x80000>; + }; + + bootloaders@80000 { + label = "u-boot"; + reg = <0x80000 0x1e0000>; + }; + + bootloaders_env@260000 { + label = "u-boot-env"; + reg = <0x260000 0x20000>; + }; + + kernel@280000 { + label = "kernel"; + reg = <0x280000 0x400000>; + }; + + filesystem@680000 { + label = "fs"; + reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */ + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; +}; + +&mmc3 { + interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; + pinctrl-0 = <&mmc3_pins>; + pinctrl-names = "default"; + vmmc-supply = <&wl12xx_vmmc>; + non-removable; + bus-width = <4>; + cap-power-off-card; + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1273"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ + ref-clock-frequency = <26000000>; + }; +}; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb2_pins>; + + mmc3_pins: pinmux_mm3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */ + OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */ + OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */ + >; + }; + mcbsp2_pins: pinmux_mcbsp2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ + OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */ + OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */ + OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */ + >; + }; + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ + OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ + OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ + OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */ + >; + }; + mcspi1_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ + >; + }; + + hsusb2_pins: pinmux_hsusb2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + >; + }; + + hsusb_otg_pins: pinmux_hsusb_otg_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + >; + }; + + +}; + +&omap3_pmx_wkup { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb2_reset_pin>; + hsusb2_reset_pin: pinmux_hsusb1_reset_pin { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ + >; + }; +}; + +&omap3_pmx_core2 { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb2_2_pins>; + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; +}; + +&uart2 { + interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&mcspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi1_pins>; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&twl { + twl_power: power { + compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle"; + ti,use_poweroff; + }; +}; + +&twl_gpio { + ti,use-leds; +};
On Mon, Apr 17, 2017 at 08:09:43AM -0500, Adam Ford wrote:
This adds the device tree. Previous commit added both boards at the same time.
Signed-off-by: Adam Ford aford173@gmail.com
Changes in V2: Split the SOM-LV from Torpedo
diff --git a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts new file mode 100644 index 0000000..1702b9e
Applied to u-boot/master, thanks!
Previous commit has this combined with SOM-LV. This commit has only the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes: disable mmc2 and stdout-path = &uart1. Both of those two changes will be submitted to the linux-omap list
Signed-off-by: Adam Ford aford173@gmail.com
Changes in V2: Split device tree from other board
diff --git a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts new file mode 100644 index 0000000..de603a4 --- /dev/null +++ b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts @@ -0,0 +1,411 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap36xx.dtsi" +#include "logicpd-torpedo-som.dtsi" +#include "omap-gpmc-smsc9221.dtsi" + +/ { + model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; + compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; + + chosen { + stdout-path = &uart1; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>; + + sysboot2 { + label = "sysboot2"; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* gpio2 */ + linux,code = <BTN_0>; + wakeup-source; + }; + + sysboot5 { + label = "sysboot5"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; /* gpio7 */ + linux,code = <BTN_1>; + wakeup-source; + }; + + gpio1 { + label = "gpio1"; + gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; /* gpio181 */ + linux,code = <BTN_2>; + wakeup-source; + }; + + gpio2 { + label = "gpio2"; + gpios = <&gpio6 18 GPIO_ACTIVE_LOW>; /* gpio178 */ + linux,code = <BTN_3>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + led1 { + label = "led1"; + gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; /* gpio180 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>; /* gpio179 */ + linux,default-trigger = "none"; + }; + }; + + pwm10: dmtimer-pwm { + compatible = "ti,omap-dmtimer-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + ti,timers = <&timer10>; + #pwm-cells = <3>; + }; + +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ + 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + + ethernet@gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + pinctrl-names = "default"; + pinctrl-0 = <&panel_pwr_pins>; + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + }; + + lcd0: display { + compatible = "panel-dpi"; + label = "15"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&pwm10 0 5000000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins &mmc1_cd>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&mmc2 { + status = "disabled"; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_clk.gpio_178 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 */ + >; + }; + + pwm_pins: pinmux_pwm_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4) /* gpio_180 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ + >; + }; + + isp_pins: pinmux_isp_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */ + OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */ + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */ + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */ + + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */ + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */ + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */ + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */ + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */ + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */ + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */ + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */ + >; + }; + + panel_pwr_pins: pinmux_panel_pwr_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data17.dss_data17 */ + + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data18.dss_data0 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data19.dss_data1 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data20.dss_data2 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data21.dss_data3 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data22.dss_data4 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data23.dss_data5 */ + >; + }; +}; + +&omap3_pmx_wkup { + gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot0.gpio_2 */ + OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot5.gpio_7 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ + >; + }; + + mmc1_cd: pinmux_mmc1_cd { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_127 */ + >; + }; +}; + +&i2c2 { + mt9p031@48 { + compatible = "aptina,mt9p031"; + reg = <0x48>; + clocks = <&isp 0>; + vaa-supply = <&vaux4>; + vdd-supply = <&vaux4>; + vdd_io-supply = <&vaux4>; + port { + mt9p031_out: endpoint { + input-clock-frequency = <24000000>; + pixel-clock-frequency = <72000000>; + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; + +&i2c3 { + touchscreen: tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vaux1>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +}; + +&mcspi1 { + at25@0 { + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; +}; + +&isp { + pinctrl-names = "default"; + pinctrl-0 = <&isp_pins>; + ports { + port@0 { + reg = <0>; + ccdc_ep: endpoint { + remote-endpoint = <&mt9p031_out>; + bus-width = <8>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; +}; + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/dts/logicpd-torpedo-som.dtsi b/arch/arm/dts/logicpd-torpedo-som.dtsi new file mode 100644 index 0000000..23c9228 --- /dev/null +++ b/arch/arm/dts/logicpd-torpedo-som.dtsi @@ -0,0 +1,217 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/input/input.h> + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0>; + }; + + leds { + compatible = "gpio-leds"; + user0 { + label = "user0"; + gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */ + linux,default-trigger = "none"; + }; + }; + + wl12xx_vmmc: wl12xx_vmmc { + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 29 0>; /* gpio157 */ + startup-delay-us = <70000>; + enable-active-high; + vin-supply = <&vmmc2>; + }; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ + + nand@0,0 { + compatible = "ti,omap2-nand"; + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ + <1 IRQ_TYPE_NONE>; /* termcount */ + linux,mtd-name = "micron,mt29f4g16abbda3w"; + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + gpmc,device-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; + at24@50 { + compatible = "at24,24c02"; + readonly; + reg = <0x50>; + }; +}; + +/* + * Only found on the wireless SOM. For the SOM without wireless, the pins for + * MMC3 can be routed with jumpers to the second MMC slot on the devkit and + * gpio157 is not connected. So this should be OK to keep common for now, + * probably device tree overlays is the way to go with the various SOM and + * jumpering combinations for the long run. + */ +&mmc3 { + interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; + pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; + pinctrl-names = "default"; + vmmc-supply = <&wl12xx_vmmc>; + non-removable; + bus-width = <4>; + cap-power-off-card; + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1283"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ + ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; + }; +}; + +&omap3_pmx_core { + mmc3_pins: pinmux_mm3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ + >; + }; + mcbsp2_pins: pinmux_mcbsp2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ + OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */ + OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */ + OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */ + >; + }; + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ + OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ + OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ + OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */ + >; + }; + mcspi1_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ + >; + }; + hsusb_otg_pins: pinmux_hsusb_otg_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + >; + }; +}; + +&uart2 { + interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&mcspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi1_pins>; +}; + +&omap3_pmx_core2 { + mmc3_core2_pins: pinmux_mmc3_core2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ + >; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&twl { + twl_power: power { + compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle"; + ti,use_poweroff; + }; +}; + +&twl_gpio { + ti,use-leds; +};
On Mon, Apr 17, 2017 at 08:09:44AM -0500, Adam Ford wrote:
Previous commit has this combined with SOM-LV. This commit has only the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes: disable mmc2 and stdout-path = &uart1. Both of those two changes will be submitted to the linux-omap list
Signed-off-by: Adam Ford aford173@gmail.com
Changes in V2: Split device tree from other board
diff --git a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts new file mode 100644 index 0000000..de603a4
Applied to u-boot/master, thanks!
This patch also removes all the excessive code for NS16550 intiailization as the device tree can do that now. This also adds DM_I2C and DM_MMC since the overlying drivers have the built-in support already. The corresponding include/config/omap3_logic.h also reduced in size due to the new device tree support.
Signed-off-by: Adam Ford aford173@gmail.com
Changes in V2: Retain Auto-detect ability between SOM-LV and Torpedo Split this off from the device sub submissions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 7378c88..44c586d 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -341,6 +341,10 @@ dtb-$(CONFIG_SOC_KEYSTONE) += keystone-k2hk-evm.dtb \ keystone-k2e-evm.dtb \ keystone-k2g-evm.dtb
+dtb-$(CONFIG_TARGET_OMAP3_LOGIC) += \ + logicpd-torpedo-37xx-devkit.dtb \ + logicpd-som-lv-37xx-devkit.dts + dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \ at91-sama5d2_xplained.dtb
diff --git a/board/logicpd/omap3som/README b/board/logicpd/omap3som/README new file mode 100644 index 0000000..06b3998 --- /dev/null +++ b/board/logicpd/omap3som/README @@ -0,0 +1,19 @@ +Summary +======= + +The source for omap3som encompases the DM3730 SOM-LV and DM3730 Torpedo platforms. + +By default, the Torpedo Device Tree is integrated into U-Boot,but the MMC controller, GPIO and I2C controllers are the same, so for the purposes of loading U-Boot, it should be sufficient. However this will display the Model as "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit" upon boot. + +The actual board remains autodetected and the Board will read "DM37xx SOM LV" when used on the DM37 SOM-LV. The device tree loaded with Linux is also correct. + +Integrating the SOM-LV Device Tree into U-Boot +============================================== + +This step is optional, but should you want to change the default to the SOM-LV, locate the configs/omap3_logic_defconfig file and make the following change. + + CONFIG_DEFAULT_DEVICE_TREE="logicpd-som-lv-37xx-devkit" + + make distclean + make omap3_logic_defconfig + diff --git a/board/logicpd/omap3som/omap3logic.c b/board/logicpd/omap3som/omap3logic.c index 4ad496e..ce17db6 100644 --- a/board/logicpd/omap3som/omap3logic.c +++ b/board/logicpd/omap3som/omap3logic.c @@ -36,16 +36,8 @@
DECLARE_GLOBAL_DATA_PTR;
-#define CONTROL_WKUP_CTRL 0x48002a5c -#define GPIO_IO_PWRDNZ (1 << 6) -#define PBIASLITEVMODE1 (1 << 8) - -/* - * two dimensional array of strucures containining board name and Linux - * machine IDs; row it selected based on CPU column is slected based - * on hsusb0_data5 pin having a pulldown resistor - */ - +/* This is only needed until SPL gets OF support */ +#ifdef CONFIG_SPL_BUILD static const struct ns16550_platdata omap3logic_serial = { .base = OMAP34XX_UART1, .reg_shift = 2, @@ -57,7 +49,13 @@ U_BOOT_DEVICE(omap3logic_uart) = { "ns16550_serial", &omap3logic_serial }; +#endif
+/* + * two dimensional array of strucures containining board name and Linux + * machine IDs; row it selected based on CPU column is slected based + * on hsusb0_data5 pin having a pulldown resistor + */ static struct board_id { char *name; int machine_id; diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig index 89bf38f..86f34bb 100644 --- a/configs/omap3_logic_defconfig +++ b/configs/omap3_logic_defconfig @@ -3,6 +3,8 @@ CONFIG_OMAP34XX=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_TARGET_OMAP3_LOGIC=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_DEFAULT_DEVICE_TREE="logicpd-torpedo-37xx-devkit" +CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="NAND" CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y @@ -36,6 +38,11 @@ CONFIG_CMD_FS_GENERIC=y CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y CONFIG_EFI_PARTITION=y +CONFIG_OF_CONTROL=y +# CONFIG_BLK is not set +CONFIG_DM_I2C=y +CONFIG_DM_MMC=y +# CONFIG_DM_MMC_OPS is not set CONFIG_MMC_OMAP_HS=y CONFIG_MMC_OMAP36XX_PINS=y CONFIG_SYS_NS16550=y @@ -46,4 +53,3 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="TI" CONFIG_G_DNL_VENDOR_NUM=0x0451 CONFIG_G_DNL_PRODUCT_NUM=0xd022 -CONFIG_OF_LIBFDT=y diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index 706175c..772fc60 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -17,12 +17,28 @@
#include <configs/ti_omap3_common.h>
+#ifdef CONFIG_SPL_BUILD +/* + * Disable MMC DM for SPL build and can be re-enabled after adding + * DM support in SPL + */ +#undef CONFIG_DM_MMC +#undef OMAP_HSMMC_USE_GPIO + +/* select serial console configuration for SPL */ +#undef CONFIG_CONS_INDEX +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 +#endif + + /* * We are only ever GP parts and will utilize all of the "downloaded image" * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in * order to allow for BCH8 to fit in. */ #undef CONFIG_SPL_TEXT_BASE +#define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_TEXT_BASE 0x40200000
#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */ @@ -34,16 +50,11 @@ /* Hardware drivers */
/* GPIO banks */ +#define CONFIG_OMAP3_GPIO_4 /* GPIO 96..128 is in GPIO bank 4 */ #define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
#define CONFIG_USB_OMAP3
-/* select serial console configuration */ -#undef CONFIG_CONS_INDEX -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 -#define CONFIG_SERIAL1 1 /* UART1 on OMAP Logic boards */ - /* commands to include */ #define CONFIG_CMD_NAND #define CONFIG_CMD_MTDPARTS @@ -52,8 +63,6 @@ /* I2C */ #define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */ -#define EXPANSION_EEPROM_I2C_BUS 2 /* I2C Bus for AT24C64 */ -#define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID
/* USB */ #define CONFIG_USB_MUSB_OMAP2PLUS
On Mon, Apr 17, 2017 at 08:09:45AM -0500, Adam Ford wrote:
This patch also removes all the excessive code for NS16550 intiailization as the device tree can do that now. This also adds DM_I2C and DM_MMC since the overlying drivers have the built-in support already. The corresponding include/config/omap3_logic.h also reduced in size due to the new device tree support.
Signed-off-by: Adam Ford aford173@gmail.com
Changes in V2: Retain Auto-detect ability between SOM-LV and Torpedo Split this off from the device sub submissions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 7378c88..44c586d 100644
Applied to u-boot/master, thanks!
participants (4)
-
Adam Ford -
Lokesh Vutla -
Simon Glass -
Tom Rini