[U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition

newer
[U-Boot] am35xx, twister: could...

older
[U-Boot] [PATCH] mx53ard: Remove...

Fabio Estevam

3 Jun 2012 3 Jun '12

9:53 a.m.

From: Fabio Estevam fabio.estevam@freescale.com

According to include/i2c.h:

"/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif "

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam fabio.estevam@freescale.com --- include/configs/imx31_phycore.h | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/imx31_phycore.h b/include/configs/imx31_phycore.h index 3153eb5..b3244b9 100644 --- a/include/configs/imx31_phycore.h +++ b/include/configs/imx31_phycore.h @@ -56,7 +56,6 @@ #define CONFIG_I2C_MXC #define CONFIG_SYS_I2C_MX31_PORT2 #define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0xfe

#define CONFIG_MXC_UART #define CONFIG_MXC_UART_BASE UART1_BASE

-- 1.7.1

Show replies by date

Fabio Estevam

3 Jun 3 Jun

9:53 a.m.

New subject: [U-Boot] [PATCH 2/6] mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition

From: Fabio Estevam fabio.estevam@freescale.com

According to include/i2c.h:

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam fabio.estevam@freescale.com --- include/configs/mx35pdk.h | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx35pdk.h b/include/configs/mx35pdk.h index bd57baa..5f75018 100644 --- a/include/configs/mx35pdk.h +++ b/include/configs/mx35pdk.h @@ -59,7 +59,6 @@ #define CONFIG_I2C_MXC #define CONFIG_SYS_I2C_MX35_PORT1 #define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0xfe #define CONFIG_MXC_SPI #define CONFIG_MXC_GPIO

-- 1.7.1

Fabio Estevam

9:53 a.m.

New subject: [U-Boot] [PATCH 3/6] mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition

According to include/i2c.h:

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam fabio.estevam@freescale.com --- include/configs/mx53ard.h | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h index f48a41e..f879edc 100644 --- a/include/configs/mx53ard.h +++ b/include/configs/mx53ard.h @@ -52,7 +52,6 @@ #define CONFIG_I2C_MXC #define CONFIG_SYS_I2C_MX53_PORT2 #define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0xfe

/* MMC Configs */ #define CONFIG_FSL_ESDHC

-- 1.7.1

Fabio Estevam

9:53 a.m.

New subject: [U-Boot] [PATCH 4/6] mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition

From: Fabio Estevam fabio.estevam@freescale.com

According to include/i2c.h:

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Cc: Jason Liu r64343@freescale.com Signed-off-by: Fabio Estevam fabio.estevam@freescale.com --- include/configs/mx53evk.h | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h index a77e5b2..2acefe9 100644 --- a/include/configs/mx53evk.h +++ b/include/configs/mx53evk.h @@ -55,7 +55,6 @@ #define CONFIG_I2C_MXC #define CONFIG_SYS_I2C_MX53_PORT2 1 #define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0xfe

/* PMIC Configs */ #define CONFIG_PMIC

-- 1.7.1

Fabio Estevam

9:53 a.m.

New subject: [U-Boot] [PATCH 5/6] mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition

From: Fabio Estevam fabio.estevam@freescale.com

According to include/i2c.h:

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Cc: Jason Liu r64343@freescale.com Signed-off-by: Fabio Estevam fabio.estevam@freescale.com --- include/configs/mx53loco.h | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h index 7d782e2..7c45647 100644 --- a/include/configs/mx53loco.h +++ b/include/configs/mx53loco.h @@ -92,7 +92,6 @@ #define CONFIG_I2C_MXC #define CONFIG_SYS_I2C_MX53_PORT1 #define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0xfe

/* PMIC Controller */ #define CONFIG_PMIC

-- 1.7.1

Fabio Estevam

9:53 a.m.

New subject: [U-Boot] [PATCH 6/6] mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition

From: Fabio Estevam fabio.estevam@freescale.com

According to include/i2c.h:

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam fabio.estevam@freescale.com --- include/configs/mx53smd.h | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/include/configs/mx53smd.h b/include/configs/mx53smd.h index a04db3f..61edd7f 100644 --- a/include/configs/mx53smd.h +++ b/include/configs/mx53smd.h @@ -52,7 +52,6 @@ #define CONFIG_I2C_MXC #define CONFIG_SYS_I2C_MX53_PORT2 #define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0xfe

/* MMC Configs */ #define CONFIG_FSL_ESDHC

-- 1.7.1

Stefano Babic

15 Jun 15 Jun

4:43 p.m.

On 03/06/2012 09:53, Fabio Estevam wrote:

...

From: Fabio Estevam fabio.estevam@freescale.com

According to include/i2c.h:

"/*

Many boards/controllers/drivers don't support an I2C slave interface so

provide a default slave address for them for use in common code. A real

value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does

support a slave interface.

*/ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif

Whole series applied to u-boot-imx, thanks.

Best regards, Stefano Babic

-- ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de =====================================================================

4711

Age (days ago)

4723

Last active (days ago)

List overview

Download

6 comments

2 participants

tags (0)

participants (2)

Fabio Estevam
Stefano Babic