[PATCH] board: rockchip: Add Pine64 PineTab2
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566 SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0: - SD-card boot - eMMC boot - SPI Flash boot - USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64, commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64 PineTab2").
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- This patch depend on the series "rockchip: rk35xx: Sync device tree with linux v6.8-rc1" [1].
[1] https://patchwork.ozlabs.org/cover/1891669/ --- arch/arm/dts/Makefile | 2 + arch/arm/dts/rk3566-pinetab2-u-boot.dtsi | 44 + arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v0.1.dts | 28 + arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v2.0.dts | 48 + arch/arm/dts/rk3566-pinetab2.dtsi | 943 ++++++++++++++++++ board/pine64/quartz64_rk3566/MAINTAINERS | 11 + configs/pinetab2-rk3566_defconfig | 119 +++ doc/board/rockchip/rockchip.rst | 1 + 10 files changed, 1202 insertions(+) create mode 100644 arch/arm/dts/rk3566-pinetab2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1.dts create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0.dts create mode 100644 arch/arm/dts/rk3566-pinetab2.dtsi create mode 100644 configs/pinetab2-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 50f35e3db3f0..825fa1cd368a 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -173,6 +173,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3566-anbernic-rgxx3.dtb \ + rk3566-pinetab2-v0.1.dtb \ + rk3566-pinetab2-v2.0.dtb \ rk3566-quartz64-a.dtb \ rk3566-quartz64-b.dtb \ rk3566-radxa-cm3-io.dtb \ diff --git a/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi new file mode 100644 index 000000000000..4aa6ab1c848c --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi @@ -0,0 +1,44 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include "rk356x-u-boot.dtsi" + +&fspi_dual_io_pins { + bootph-all; +}; + +&gpio0 { + bootph-all; +}; + +&i2c0 { + bootph-pre-ram; +}; + +&rk817 { + bootph-pre-ram; + + regulators { + bootph-pre-ram; + }; +}; + +&sdhci { + cap-mmc-highspeed; +}; + +&sdmmc_pwren_l { + bootph-all; +}; + +&sfc { + bootph-pre-ram; + u-boot,spl-sfc-no-dma; + + flash@0 { + bootph-pre-ram; + }; +}; + +&vcc3v3_sd { + bootph-pre-ram; +}; diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1.dts b/arch/arm/dts/rk3566-pinetab2-v0.1.dts new file mode 100644 index 000000000000..5fe6ca5da9d3 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1.dts @@ -0,0 +1,28 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; + +#include "rk3566-pinetab2.dtsi" + +/ { + model = "Pine64 PineTab2 v0.1"; + compatible = "pine64,pinetab2-v0.1", "pine64,pinetab2", "rockchip,rk3566"; +}; + +&lcd { + reset-gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>; +}; + +&pinctrl { + lcd0 { + lcd0_rst_l: lcd0-rst-l { + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&sdmmc1 { + vmmc-supply = <&vcc3v3_sys>; +}; diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0.dts b/arch/arm/dts/rk3566-pinetab2-v2.0.dts new file mode 100644 index 000000000000..9349541cbbd0 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0.dts @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; + +#include "rk3566-pinetab2.dtsi" + +/ { + model = "Pine64 PineTab2 v2.0"; + compatible = "pine64,pinetab2-v2.0", "pine64,pinetab2", "rockchip,rk3566"; +}; + +&gpio_keys { + pinctrl-0 = <&kb_id_det>, <&hall_int_l>; + + event-hall-sensor { + debounce-interval = <20>; + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>; + label = "Hall Sensor"; + linux,code = <SW_LID>; + linux,input-type = <EV_SW>; + wakeup-event-action = <EV_ACT_DEASSERTED>; + wakeup-source; + }; +}; + +&lcd { + reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>; +}; + +&pinctrl { + lcd0 { + lcd0_rst_l: lcd0-rst-l { + rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hall { + hall_int_l: hall-int-l { + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&sdmmc1 { + vmmc-supply = <&vcc_sys>; +}; diff --git a/arch/arm/dts/rk3566-pinetab2.dtsi b/arch/arm/dts/rk3566-pinetab2.dtsi new file mode 100644 index 000000000000..db40281eafbe --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2.dtsi @@ -0,0 +1,943 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,vop2.h> +#include <dt-bindings/usb/pd.h> +#include "rk3566.dtsi" + +/ { + chassis-type = "tablet"; + + aliases { + mmc0 = &sdhci; + mmc1 = &sdmmc0; + }; + + chosen { + stdout-path = "serial2:1500000n8"; + }; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1800000>; + poll-interval = <25>; + + button-vol-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <297500>; + }; + + button-vol-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <1750>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm4 0 25000 0>; + brightness-levels = <20 220>; + num-interpolated-steps = <200>; + default-brightness-level = <100>; + power-supply = <&vcc_sys>; + }; + + battery: battery { + compatible = "simple-battery"; + charge-full-design-microamp-hours = <6000000>; + charge-term-current-microamp = <300000>; + constant-charge-current-max-microamp = <2000000>; + constant-charge-voltage-max-microvolt = <4300000>; + voltage-max-design-microvolt = <4350000>; + voltage-min-design-microvolt = <3400000>; + + ocv-capacity-celsius = <20>; + ocv-capacity-table-0 = <4322000 100>, <4250000 95>, <4192000 90>, <4136000 85>, + <4080000 80>, <4022000 75>, <3972000 70>, <3928000 65>, + <3885000 60>, <3833000 55>, <3798000 50>, <3780000 45>, + <3776000 40>, <3773000 35>, <3755000 30>, <3706000 25>, + <3640000 20>, <3589000 15>, <3535000 10>, <3492000 5>, + <3400000 0>; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&kb_id_det>; + + tablet-mode-switch { + debounce-interval = <20>; + gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>; + label = "Tablet Mode"; + linux,input-type = <EV_SW>; + linux,code = <SW_TABLET_MODE>; + }; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "d"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + led-0 { + compatible = "regulator-led"; + vled-supply = <&vcc5v0_flashled>; + color = <LED_COLOR_ID_WHITE>; + function = LED_FUNCTION_FLASH; + }; + + rk817-sound { + compatible = "simple-audio-card"; + pinctrl-names = "default"; + pinctrl-0 = <&hp_det_l>; + simple-audio-card,format = "i2s"; + simple-audio-card,name = "rk817_ext"; + simple-audio-card,mclk-fs = <256>; + + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Headphone", "Headphones", + "Speaker", "Internal Speakers"; + + simple-audio-card,routing = + "MICR", "Mic Jack", + "Headphones", "HPOL", + "Headphones", "HPOR", + "Internal Speakers", "Speaker Amplifier OUTL", + "Internal Speakers", "Speaker Amplifier OUTR", + "Speaker Amplifier INL", "HPOL", + "Speaker Amplifier INR", "HPOR"; + simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>; + simple-audio-card,aux-devs = <&speaker_amp>; + simple-audio-card,pin-switches = "Internal Speakers"; + + simple-audio-card,cpu { + sound-dai = <&i2s1_8ch>; + }; + + simple-audio-card,codec { + sound-dai = <&rk817>; + }; + }; + + speaker_amp: speaker-amplifier { + compatible = "simple-audio-amplifier"; + pinctrl-names = "default"; + pinctrl-0 = <&spk_ctl>; + enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>; + sound-name-prefix = "Speaker Amplifier"; + VCC-supply = <&vcc_bat>; + }; + + vcc_3v3: vcc-3v3-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc3v3_sys>; + }; + + vcc3v3_minipcie: vcc3v3-minipcie-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_pwren_h>; + regulator-name = "vcc3v3_minipcie"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_sys>; + }; + + vcc3v3_sd: vcc3v3-sd-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwren_l>; + regulator-name = "vcc3v3_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc3v3_sys>; + }; + + vcc5v0_flashled: vcc5v0-flashled-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&flash_led_en_h>; + regulator-name = "vcc5v0_flashled"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v_midu>; + }; + + vcc5v0_usb_host0: vcc5v0-usb-host0-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_host_pwren1_h>; + regulator-name = "vcc5v0_usb_host0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v_midu>; + }; + + vcc5v0_usb_host2: vcc5v0-usb-host2-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_host_pwren2_h>; + regulator-name = "vcc5v0_usb_host2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v_midu>; + }; + + vcc_bat: vcc-bat-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_bat"; + regulator-always-on; + regulator-boot-on; + }; + + vcc_sys: vcc-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_bat>; + }; + + vdd1v2_dvp: vdd1v2-dvp-regulator { + compatible = "regulator-fixed"; + regulator-name = "vdd1v2_dvp"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <&vcc_3v3>; + }; +}; + +&combphy1 { + status = "okay"; +}; + +&combphy2 { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu1 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu2 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu3 { + cpu-supply = <&vdd_cpu>; +}; + +&cru { + assigned-clocks = <&pmucru CLK_RTC_32K>, <&cru PLL_GPLL>, + <&pmucru PLL_PPLL>, <&cru PLL_VPLL>; + assigned-clock-rates = <32768>, <1200000000>, <200000000>, <500000000>; + assigned-clock-parents = <&pmucru CLK_RTC32K_FRAC>; +}; + +&csi_dphy { + status = "okay"; +}; + +&dsi0 { + status = "okay"; + clock-master; + #address-cells = <1>; + #size-cells = <0>; + + lcd: panel@0 { + compatible = "boe,th101mb31ig002-28a"; + reg = <0>; + backlight = <&backlight>; + enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>; + rotation = <90>; + power-supply = <&vcc_3v3>; + + port@0 { + panel_in_dsi: endpoint@0 { + remote-endpoint = <&dsi0_out_con>; + }; + }; + }; +}; + +&dsi0_in { + dsi0_in_vp1: endpoint { + remote-endpoint = <&vp1_out_dsi0>; + }; +}; + +&dsi0_out { + dsi0_out_con: endpoint { + remote-endpoint = <&panel_in_dsi>; + }; +}; + +&dsi_dphy0 { + status = "okay"; +}; + +&gpu { + mali-supply = <&vdd_gpu_npu>; + status = "okay"; +}; + +&hdmi { + avdd-0v9-supply = <&vdda_0v9_p>; + avdd-1v8-supply = <&vcc_1v8>; + status = "okay"; +}; + +&hdmi_in { + hdmi_in_vp0: endpoint { + remote-endpoint = <&vp0_out_hdmi>; + }; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&hdmi_sound { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + vdd_cpu: regulator@1c { + compatible = "tcs,tcs4525"; + reg = <0x1c>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-ramp-delay = <2300>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + rk817: pmic@20 { + compatible = "rockchip,rk817"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; + assigned-clocks = <&cru I2S1_MCLKOUT_TX>; + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>; + clock-names = "mclk"; + clocks = <&cru I2S1_MCLKOUT_TX>; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + #clock-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>; + rockchip,system-power-controller; + #sound-dai-cells = <0>; + wakeup-source; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc5-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; + vcc8-supply = <&vcc_sys>; + vcc9-supply = <&vcc5v_midu>; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-name = "vdd_logic"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu_npu: DCDC_REG2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-name = "vdd_gpu_npu"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc3v3_sys: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <0x2>; + regulator-name = "vcc3v3_sys"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca1v8_pmu: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca1v8_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vdda_0v9_p: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdda_0v9_p"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_pmu: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdda0v9_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vccio_acodec: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_acodec"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_pmu: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_1v8: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_1v8"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc1v8_dvp: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8_dvp"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc2v8_dvp: LDO_REG9 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc2v8_dvp"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc5v_midu: BOOST { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "boost"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vbus: OTG_SWITCH { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "otg_switch"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + + charger { + monitored-battery = <&battery>; + rockchip,resistor-sense-micro-ohms = <10000>; + rockchip,sleep-enter-current-microamp = <300000>; + rockchip,sleep-filter-current-microamp = <100000>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + status = "okay"; + + touchscreen@5d { + compatible = "goodix,gt911"; + reg = <0x5d>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PB0 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&tp_int_l_pmuio2>, <&tp_rst_l_pmuio2>; + AVDD28-supply = <&vcc3v3_pmu>; + VDDIO-supply = <&vcca1v8_pmu>; + irq-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-0 = <&i2c2m1_xfer>; + status = "okay"; + + vcm@c { + compatible = "dongwoon,dw9714"; + reg = <0x0c>; + vcc-supply = <&vcc1v8_dvp>; + }; + + camera@36 { + compatible = "ovti,ov5648"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&camerab_pdn_l &camerab_rst_l>; + + clocks = <&cru CLK_CIF_OUT>; + assigned-clocks = <&cru CLK_CIF_OUT>; + assigned-clock-rates = <24000000>; + + avdd-supply = <&vcc2v8_dvp>; + dvdd-supply = <&vdd1v2_dvp>; + dovdd-supply = <&vcc1v8_dvp>; + powerdown-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio4 RK_PB1 GPIO_ACTIVE_LOW>; + + port { + endpoint { + data-lanes = <1 2>; + remote-endpoint = <0>; + link-frequencies = /bits/ 64 <210000000 168000000>; + }; + }; + }; +}; + +&i2c5 { + clock-frequency = <400000>; + status = "okay"; + + accelerometer@18 { + compatible = "silan,sc7a20"; + reg = <0x18>; + interrupt-parent = <&gpio3>; + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&gsensor_int_l>; + st,drdy-int-pin = <1>; + vdd-supply = <&vcc_1v8>; + vddio-supply = <&vcc_1v8>; + mount-matrix = "1", "0", "0", + "0", "0", "1", + "0", "1", "0"; + }; +}; + +&i2s0_8ch { + status = "okay"; +}; + +&i2s1_8ch { + pinctrl-names = "default"; + pinctrl-0 = <&i2s1m0_sclktx + &i2s1m0_lrcktx + &i2s1m0_sdi0 + &i2s1m0_sdo0>; + rockchip,trcm-sync-tx-only; + status = "okay"; +}; + +&pcie2x1 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_reset_h>; + reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_minipcie>; + status = "okay"; +}; + +&pinctrl { + camerab { + camerab_pdn_l: camerab-pdn-l { + rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + camerab_rst_l: camerab-rst-l { + rockchip,pins = <4 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + cameraf { + cameraf_pdn_l: cameraf-pdn-l { + rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + cameraf_rst_l: cameraf-rst-l { + rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + flash { + flash_led_en_h: flash-led-en-h { + rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + fspi { + fspi_dual_io_pins: fspi-dual-io-pins { + rockchip,pins = + /* fspi_clk */ + <1 RK_PD0 1 &pcfg_pull_none>, + /* fspi_cs0n */ + <1 RK_PD3 1 &pcfg_pull_none>, + /* fspi_d0 */ + <1 RK_PD1 1 &pcfg_pull_none>, + /* fspi_d1 */ + <1 RK_PD2 1 &pcfg_pull_none>; + }; + }; + + gsensor { + gsensor_int_l: gsensor-int-l { + rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + kb { + kb_id_det: kb-id-det { + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + lcd { + lcd_pwren_h: lcd-pwren-h { + rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pcie { + pcie_pwren_h: pcie-pwren-h { + rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie_reset_h: pcie-reset-h { + rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + sdmmc { + sdmmc_pwren_l: sdmmc-pwren-l { + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sound { + hp_det_l: hp-det-l { + rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + spk_ctl: spk-ctl { + rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + tp { + tp_int_l_pmuio2: tp-int-l-pmuio2 { + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + tp_rst_l_pmuio2: tp-rst-l-pmuio2 { + rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb { + usbcc_int_l: usbcc-int-l { + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + usb_host_pwren1_h: usb-host-pwren1-h { + rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + usb_host_pwren2_h: usb-host-pwren2-h { + rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + wifi { + host_wake_wl: host-wake-wl { + rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + wifi_wake_host_h: wifi-wake-host-h { + rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; +}; + +&pmu_io_domains { + pmuio1-supply = <&vcc3v3_pmu>; + pmuio2-supply = <&vcca1v8_pmu>; + vccio1-supply = <&vccio_acodec>; + vccio2-supply = <&vcc_1v8>; + vccio3-supply = <&vccio_sd>; + vccio4-supply = <&vcc_1v8>; + vccio5-supply = <&vcc_1v8>; + vccio6-supply = <&vcc1v8_dvp>; + vccio7-supply = <&vcc_3v3>; + status = "okay"; +}; + +&pwm4 { + status = "okay"; +}; + +&saradc { + vref-supply = <&vcc_1v8>; + status = "okay"; +}; + +&sdhci { + bus-width = <8>; + no-sdio; + no-sd; + non-removable; + max-frequency = <200000000>; + mmc-hs200-1_8v; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_bus8 + &emmc_clk + &emmc_cmd + &emmc_datastrobe + &emmc_rstnout>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc_1v8>; + status = "okay"; +}; + +&sdmmc0 { + bus-width = <4>; + cap-sd-highspeed; + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>; + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_bus4 + &sdmmc0_clk + &sdmmc0_cmd + &sdmmc0_det>; + sd-uhs-sdr104; + vmmc-supply = <&vcc3v3_sd>; + vqmmc-supply = <&vccio_sd>; + status = "okay"; +}; + +&sdmmc1 { + bus-width = <4>; + cap-sd-highspeed; + cap-sdio-irq; + keep-power-in-suspend; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc1_bus4 + &sdmmc1_cmd + &sdmmc1_clk>; + sd-uhs-sdr104; + vqmmc-supply = <&vcca1v8_pmu>; + status = "okay"; +}; + +&sfc { + pinctrl-names = "default"; + pinctrl-0 = <&fspi_dual_io_pins>; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <100000000>; + spi-rx-bus-width = <2>; + spi-tx-bus-width = <1>; + }; +}; + +&tsadc { + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <0>; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +}; + +&usb_host0_xhci { + status = "okay"; +}; + +&usb_host1_xhci { + status = "okay"; +}; + +&usb2phy0 { + status = "okay"; +}; + +&usb2phy0_host { + phy-supply = <&vcc5v0_usb_host0>; + status = "okay"; +}; + +&usb2phy0_otg { + status = "okay"; +}; + +&usb2phy1 { + status = "okay"; +}; + +&usb2phy1_otg { + phy-supply = <&vcc5v0_usb_host2>; + status = "okay"; +}; + +&vop { + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; + status = "okay"; +}; + +&vop_mmu { + status = "okay"; +}; + +&vp0 { + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { + reg = <ROCKCHIP_VOP2_EP_HDMI0>; + remote-endpoint = <&hdmi_in_vp0>; + }; +}; + +&vp1 { + vp1_out_dsi0: endpoint@ROCKCHIP_VOP2_EP_MIPI0 { + reg = <ROCKCHIP_VOP2_EP_MIPI0>; + remote-endpoint = <&dsi0_in_vp1>; + }; +}; diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS index 6b75b35a1243..37b8c1eb78b6 100644 --- a/board/pine64/quartz64_rk3566/MAINTAINERS +++ b/board/pine64/quartz64_rk3566/MAINTAINERS @@ -21,3 +21,14 @@ F: arch/arm/dts/rk3566-soquartz-cm4.dts F: arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi F: arch/arm/dts/rk3566-soquartz-model-a.dts F: arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi + +PINETAB2-RK3566 +M: Jonas Karlman jonas@kwiboo.se +S: Maintained +F: configs/pinetab2-rk3566_defconfig +F: arch/arm/dts/rk3566-pinetab2.dtsi +F: arch/arm/dts/rk3566-pinetab2-u-boot.dtsi +F: arch/arm/dts/rk3566-pinetab2-v0.1.dts +F: arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi +F: arch/arm/dts/rk3566-pinetab2-v2.0.dts +F: arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi diff --git a/configs/pinetab2-rk3566_defconfig b/configs/pinetab2-rk3566_defconfig new file mode 100644 index 000000000000..19b396eef975 --- /dev/null +++ b/configs/pinetab2-rk3566_defconfig @@ -0,0 +1,119 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_GPIO=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x1000 +CONFIG_DEFAULT_DEVICE_TREE="rk3566-pinetab2-v2.0" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y +CONFIG_ROCKCHIP_SPI_IMAGE=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_TARGET_QUARTZ64_RK3566=y +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-pinetab2-v2.0.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_I2C=y +CONFIG_SPL_POWER=y +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_POWEROFF=y +CONFIG_CMD_USB=y +CONFIG_CMD_ROCKUSB=y +CONFIG_CMD_USB_MASS_STORAGE=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_OF_LIST="rk3566-pinetab2-v0.1 rk3566-pinetab2-v2.0" +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_BUTTON=y +CONFIG_BUTTON_ADC=y +CONFIG_BUTTON_GPIO=y +CONFIG_SPL_CLK=y +# CONFIG_USB_FUNCTION_FASTBOOT is not set +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_SF_DEFAULT_BUS=4 +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_SILICONKAISER=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_SPL_PMIC_RK8XX=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_SPL_DM_REGULATOR_FIXED=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_ROCKCHIP_SFC=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_PSCI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_ETHER_ASIX88179=y +CONFIG_USB_ETHER_RTL8152=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_PRODUCT_NUM=0x350a +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_FUNCTION_ROCKUSB=y +CONFIG_ERRNO_STR=y diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst index 9fe69fc9422f..fda2282b2c26 100644 --- a/doc/board/rockchip/rockchip.rst +++ b/doc/board/rockchip/rockchip.rst @@ -93,6 +93,7 @@ List of mainline supported Rockchip boards:
* rk3566 - Anbernic RGxx3 (anbernic-rgxx3-rk3566) + - Pine64 PineTab2 (pinetab2-rk3566) - Pine64 Quartz64-A Board (quartz64-a-rk3566) - Pine64 Quartz64-B Board (quartz64-b-rk3566) - Pine64 SOQuartz on Blade (soquartz-blade-rk3566)
Hi Jonas,
On 2024/2/5 01:30, Jonas Karlman wrote:
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566 SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64, commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64 PineTab2").
Signed-off-by: Jonas Karlman jonas@kwiboo.se
This patch depend on the series "rockchip: rk35xx: Sync device tree with linux v6.8-rc1" [1].
[1] https://patchwork.ozlabs.org/cover/1891669/
arch/arm/dts/Makefile | 2 + arch/arm/dts/rk3566-pinetab2-u-boot.dtsi | 44 + arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v0.1.dts | 28 +
Does this v0.1 version dts really needed? This seems like a test version instead of release version hardware?
Thanks,
- Kever
arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v2.0.dts | 48 + arch/arm/dts/rk3566-pinetab2.dtsi | 943 ++++++++++++++++++ board/pine64/quartz64_rk3566/MAINTAINERS | 11 + configs/pinetab2-rk3566_defconfig | 119 +++ doc/board/rockchip/rockchip.rst | 1 + 10 files changed, 1202 insertions(+) create mode 100644 arch/arm/dts/rk3566-pinetab2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1.dts create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0.dts create mode 100644 arch/arm/dts/rk3566-pinetab2.dtsi create mode 100644 configs/pinetab2-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 50f35e3db3f0..825fa1cd368a 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -173,6 +173,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3566-anbernic-rgxx3.dtb \
- rk3566-pinetab2-v0.1.dtb \
- rk3566-pinetab2-v2.0.dtb \ rk3566-quartz64-a.dtb \ rk3566-quartz64-b.dtb \ rk3566-radxa-cm3-io.dtb \
diff --git a/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi new file mode 100644 index 000000000000..4aa6ab1c848c --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi @@ -0,0 +1,44 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk356x-u-boot.dtsi"
+&fspi_dual_io_pins {
- bootph-all;
+};
+&gpio0 {
- bootph-all;
+};
+&i2c0 {
- bootph-pre-ram;
+};
+&rk817 {
- bootph-pre-ram;
- regulators {
bootph-pre-ram;- };
+};
+&sdhci {
- cap-mmc-highspeed;
+};
+&sdmmc_pwren_l {
- bootph-all;
+};
+&sfc {
- bootph-pre-ram;
- u-boot,spl-sfc-no-dma;
- flash@0 {
bootph-pre-ram;- };
+};
+&vcc3v3_sd {
- bootph-pre-ram;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1.dts b/arch/arm/dts/rk3566-pinetab2-v0.1.dts new file mode 100644 index 000000000000..5fe6ca5da9d3 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1.dts @@ -0,0 +1,28 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "rk3566-pinetab2.dtsi"
+/ {
- model = "Pine64 PineTab2 v0.1";
- compatible = "pine64,pinetab2-v0.1", "pine64,pinetab2", "rockchip,rk3566";
+};
+&lcd {
- reset-gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+&pinctrl {
- lcd0 {
lcd0_rst_l: lcd0-rst-l {rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
+};
+&sdmmc1 {
- vmmc-supply = <&vcc3v3_sys>;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0.dts b/arch/arm/dts/rk3566-pinetab2-v2.0.dts new file mode 100644 index 000000000000..9349541cbbd0 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0.dts @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "rk3566-pinetab2.dtsi"
+/ {
- model = "Pine64 PineTab2 v2.0";
- compatible = "pine64,pinetab2-v2.0", "pine64,pinetab2", "rockchip,rk3566";
+};
+&gpio_keys {
- pinctrl-0 = <&kb_id_det>, <&hall_int_l>;
- event-hall-sensor {
debounce-interval = <20>;gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;label = "Hall Sensor";linux,code = <SW_LID>;linux,input-type = <EV_SW>;wakeup-event-action = <EV_ACT_DEASSERTED>;wakeup-source;- };
+};
+&lcd {
- reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+&pinctrl {
- lcd0 {
lcd0_rst_l: lcd0-rst-l {rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- hall {
hall_int_l: hall-int-l {rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
+};
+&sdmmc1 {
- vmmc-supply = <&vcc_sys>;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2.dtsi b/arch/arm/dts/rk3566-pinetab2.dtsi new file mode 100644 index 000000000000..db40281eafbe --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2.dtsi @@ -0,0 +1,943 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,vop2.h> +#include <dt-bindings/usb/pd.h> +#include "rk3566.dtsi"
+/ {
- chassis-type = "tablet";
- aliases {
mmc0 = &sdhci;mmc1 = &sdmmc0;- };
- chosen {
stdout-path = "serial2:1500000n8";- };
- adc-keys {
compatible = "adc-keys";io-channels = <&saradc 0>;io-channel-names = "buttons";keyup-threshold-microvolt = <1800000>;poll-interval = <25>;button-vol-up {label = "Volume Up";linux,code = <KEY_VOLUMEUP>;press-threshold-microvolt = <297500>;};button-vol-down {label = "Volume Down";linux,code = <KEY_VOLUMEDOWN>;press-threshold-microvolt = <1750>;};- };
- backlight: backlight {
compatible = "pwm-backlight";pwms = <&pwm4 0 25000 0>;brightness-levels = <20 220>;num-interpolated-steps = <200>;default-brightness-level = <100>;power-supply = <&vcc_sys>;- };
- battery: battery {
compatible = "simple-battery";charge-full-design-microamp-hours = <6000000>;charge-term-current-microamp = <300000>;constant-charge-current-max-microamp = <2000000>;constant-charge-voltage-max-microvolt = <4300000>;voltage-max-design-microvolt = <4350000>;voltage-min-design-microvolt = <3400000>;ocv-capacity-celsius = <20>;ocv-capacity-table-0 = <4322000 100>, <4250000 95>, <4192000 90>, <4136000 85>,<4080000 80>, <4022000 75>, <3972000 70>, <3928000 65>,<3885000 60>, <3833000 55>, <3798000 50>, <3780000 45>,<3776000 40>, <3773000 35>, <3755000 30>, <3706000 25>,<3640000 20>, <3589000 15>, <3535000 10>, <3492000 5>,<3400000 0>;- };
- gpio_keys: gpio-keys {
compatible = "gpio-keys";pinctrl-names = "default";pinctrl-0 = <&kb_id_det>;tablet-mode-switch {debounce-interval = <20>;gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;label = "Tablet Mode";linux,input-type = <EV_SW>;linux,code = <SW_TABLET_MODE>;};- };
- hdmi-connector {
compatible = "hdmi-connector";type = "d";port {hdmi_con_in: endpoint {remote-endpoint = <&hdmi_out_con>;};};- };
- led-0 {
compatible = "regulator-led";vled-supply = <&vcc5v0_flashled>;color = <LED_COLOR_ID_WHITE>;function = LED_FUNCTION_FLASH;- };
- rk817-sound {
compatible = "simple-audio-card";pinctrl-names = "default";pinctrl-0 = <&hp_det_l>;simple-audio-card,format = "i2s";simple-audio-card,name = "rk817_ext";simple-audio-card,mclk-fs = <256>;simple-audio-card,widgets ="Microphone", "Mic Jack","Headphone", "Headphones","Speaker", "Internal Speakers";simple-audio-card,routing ="MICR", "Mic Jack","Headphones", "HPOL","Headphones", "HPOR","Internal Speakers", "Speaker Amplifier OUTL","Internal Speakers", "Speaker Amplifier OUTR","Speaker Amplifier INL", "HPOL","Speaker Amplifier INR", "HPOR";simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;simple-audio-card,aux-devs = <&speaker_amp>;simple-audio-card,pin-switches = "Internal Speakers";simple-audio-card,cpu {sound-dai = <&i2s1_8ch>;};simple-audio-card,codec {sound-dai = <&rk817>;};- };
- speaker_amp: speaker-amplifier {
compatible = "simple-audio-amplifier";pinctrl-names = "default";pinctrl-0 = <&spk_ctl>;enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;sound-name-prefix = "Speaker Amplifier";VCC-supply = <&vcc_bat>;- };
- vcc_3v3: vcc-3v3-regulator {
compatible = "regulator-fixed";regulator-name = "vcc_3v3";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;vin-supply = <&vcc3v3_sys>;- };
- vcc3v3_minipcie: vcc3v3-minipcie-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&pcie_pwren_h>;regulator-name = "vcc3v3_minipcie";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;vin-supply = <&vcc_sys>;- };
- vcc3v3_sd: vcc3v3-sd-regulator {
compatible = "regulator-fixed";gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&sdmmc_pwren_l>;regulator-name = "vcc3v3_sd";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;vin-supply = <&vcc3v3_sys>;- };
- vcc5v0_flashled: vcc5v0-flashled-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&flash_led_en_h>;regulator-name = "vcc5v0_flashled";regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;vin-supply = <&vcc5v_midu>;- };
- vcc5v0_usb_host0: vcc5v0-usb-host0-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&usb_host_pwren1_h>;regulator-name = "vcc5v0_usb_host0";regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;vin-supply = <&vcc5v_midu>;- };
- vcc5v0_usb_host2: vcc5v0-usb-host2-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&usb_host_pwren2_h>;regulator-name = "vcc5v0_usb_host2";regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;vin-supply = <&vcc5v_midu>;- };
- vcc_bat: vcc-bat-regulator {
compatible = "regulator-fixed";regulator-name = "vcc_bat";regulator-always-on;regulator-boot-on;- };
- vcc_sys: vcc-sys-regulator {
compatible = "regulator-fixed";regulator-name = "vcc_sys";regulator-always-on;regulator-boot-on;vin-supply = <&vcc_bat>;- };
- vdd1v2_dvp: vdd1v2-dvp-regulator {
compatible = "regulator-fixed";regulator-name = "vdd1v2_dvp";regulator-min-microvolt = <1200000>;regulator-max-microvolt = <1200000>;vin-supply = <&vcc_3v3>;- };
+};
+&combphy1 {
- status = "okay";
+};
+&combphy2 {
- status = "okay";
+};
+&cpu0 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu1 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu2 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu3 {
- cpu-supply = <&vdd_cpu>;
+};
+&cru {
- assigned-clocks = <&pmucru CLK_RTC_32K>, <&cru PLL_GPLL>,
<&pmucru PLL_PPLL>, <&cru PLL_VPLL>;- assigned-clock-rates = <32768>, <1200000000>, <200000000>, <500000000>;
- assigned-clock-parents = <&pmucru CLK_RTC32K_FRAC>;
+};
+&csi_dphy {
- status = "okay";
+};
+&dsi0 {
- status = "okay";
- clock-master;
- #address-cells = <1>;
- #size-cells = <0>;
- lcd: panel@0 {
compatible = "boe,th101mb31ig002-28a";reg = <0>;backlight = <&backlight>;enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;rotation = <90>;power-supply = <&vcc_3v3>;port@0 {panel_in_dsi: endpoint@0 {remote-endpoint = <&dsi0_out_con>;};};- };
+};
+&dsi0_in {
- dsi0_in_vp1: endpoint {
remote-endpoint = <&vp1_out_dsi0>;- };
+};
+&dsi0_out {
- dsi0_out_con: endpoint {
remote-endpoint = <&panel_in_dsi>;- };
+};
+&dsi_dphy0 {
- status = "okay";
+};
+&gpu {
- mali-supply = <&vdd_gpu_npu>;
- status = "okay";
+};
+&hdmi {
- avdd-0v9-supply = <&vdda_0v9_p>;
- avdd-1v8-supply = <&vcc_1v8>;
- status = "okay";
+};
+&hdmi_in {
- hdmi_in_vp0: endpoint {
remote-endpoint = <&vp0_out_hdmi>;- };
+};
+&hdmi_out {
- hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;- };
+};
+&hdmi_sound {
- status = "okay";
+};
+&i2c0 {
- clock-frequency = <400000>;
- status = "okay";
- vdd_cpu: regulator@1c {
compatible = "tcs,tcs4525";reg = <0x1c>;fcs,suspend-voltage-selector = <1>;regulator-name = "vdd_cpu";regulator-min-microvolt = <800000>;regulator-max-microvolt = <1150000>;regulator-ramp-delay = <2300>;regulator-always-on;regulator-boot-on;vin-supply = <&vcc_sys>;regulator-state-mem {regulator-off-in-suspend;};- };
- rk817: pmic@20 {
compatible = "rockchip,rk817";reg = <0x20>;interrupt-parent = <&gpio0>;interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;assigned-clocks = <&cru I2S1_MCLKOUT_TX>;assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;clock-names = "mclk";clocks = <&cru I2S1_MCLKOUT_TX>;clock-output-names = "rk808-clkout1", "rk808-clkout2";#clock-cells = <1>;pinctrl-names = "default";pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;rockchip,system-power-controller;#sound-dai-cells = <0>;wakeup-source;vcc1-supply = <&vcc_sys>;vcc2-supply = <&vcc_sys>;vcc3-supply = <&vcc_sys>;vcc4-supply = <&vcc_sys>;vcc5-supply = <&vcc_sys>;vcc6-supply = <&vcc_sys>;vcc7-supply = <&vcc_sys>;vcc8-supply = <&vcc_sys>;vcc9-supply = <&vcc5v_midu>;regulators {vdd_logic: DCDC_REG1 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <500000>;regulator-max-microvolt = <1350000>;regulator-ramp-delay = <6001>;regulator-initial-mode = <0x2>;regulator-name = "vdd_logic";regulator-state-mem {regulator-off-in-suspend;};};vdd_gpu_npu: DCDC_REG2 {regulator-min-microvolt = <500000>;regulator-max-microvolt = <1350000>;regulator-ramp-delay = <6001>;regulator-initial-mode = <0x2>;regulator-name = "vdd_gpu_npu";regulator-state-mem {regulator-off-in-suspend;};};vcc_ddr: DCDC_REG3 {regulator-always-on;regulator-boot-on;regulator-initial-mode = <0x2>;regulator-name = "vcc_ddr";regulator-state-mem {regulator-on-in-suspend;};};vcc3v3_sys: DCDC_REG4 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-initial-mode = <0x2>;regulator-name = "vcc3v3_sys";regulator-state-mem {regulator-off-in-suspend;};};vcca1v8_pmu: LDO_REG1 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-name = "vcca1v8_pmu";regulator-state-mem {regulator-on-in-suspend;};};vdda_0v9_p: LDO_REG2 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <900000>;regulator-max-microvolt = <900000>;regulator-name = "vdda_0v9_p";regulator-state-mem {regulator-off-in-suspend;};};vdda0v9_pmu: LDO_REG3 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <900000>;regulator-max-microvolt = <900000>;regulator-name = "vdda0v9_pmu";regulator-state-mem {regulator-on-in-suspend;};};vccio_acodec: LDO_REG4 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-name = "vccio_acodec";regulator-state-mem {regulator-off-in-suspend;};};vccio_sd: LDO_REG5 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <3300000>;regulator-name = "vccio_sd";regulator-state-mem {regulator-off-in-suspend;};};vcc3v3_pmu: LDO_REG6 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-name = "vcc3v3_pmu";regulator-state-mem {regulator-on-in-suspend;};};vcc_1v8: LDO_REG7 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-name = "vcc_1v8";regulator-state-mem {regulator-off-in-suspend;};};vcc1v8_dvp: LDO_REG8 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-name = "vcc1v8_dvp";regulator-state-mem {regulator-off-in-suspend;};};vcc2v8_dvp: LDO_REG9 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <2800000>;regulator-max-microvolt = <2800000>;regulator-name = "vcc2v8_dvp";regulator-state-mem {regulator-off-in-suspend;};};vcc5v_midu: BOOST {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;regulator-name = "boost";regulator-state-mem {regulator-off-in-suspend;};};vbus: OTG_SWITCH {regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;regulator-name = "otg_switch";regulator-state-mem {regulator-off-in-suspend;};};};charger {monitored-battery = <&battery>;rockchip,resistor-sense-micro-ohms = <10000>;rockchip,sleep-enter-current-microamp = <300000>;rockchip,sleep-filter-current-microamp = <100000>;};- };
+};
+&i2c1 {
- clock-frequency = <400000>;
- status = "okay";
- touchscreen@5d {
compatible = "goodix,gt911";reg = <0x5d>;interrupt-parent = <&gpio0>;interrupts = <RK_PB0 IRQ_TYPE_EDGE_FALLING>;pinctrl-names = "default";pinctrl-0 = <&tp_int_l_pmuio2>, <&tp_rst_l_pmuio2>;AVDD28-supply = <&vcc3v3_pmu>;VDDIO-supply = <&vcca1v8_pmu>;irq-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;reset-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;- };
+};
+&i2c2 {
- clock-frequency = <400000>;
- pinctrl-0 = <&i2c2m1_xfer>;
- status = "okay";
- vcm@c {
compatible = "dongwoon,dw9714";reg = <0x0c>;vcc-supply = <&vcc1v8_dvp>;- };
- camera@36 {
compatible = "ovti,ov5648";reg = <0x36>;pinctrl-names = "default";pinctrl-0 = <&camerab_pdn_l &camerab_rst_l>;clocks = <&cru CLK_CIF_OUT>;assigned-clocks = <&cru CLK_CIF_OUT>;assigned-clock-rates = <24000000>;avdd-supply = <&vcc2v8_dvp>;dvdd-supply = <&vdd1v2_dvp>;dovdd-supply = <&vcc1v8_dvp>;powerdown-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;reset-gpios = <&gpio4 RK_PB1 GPIO_ACTIVE_LOW>;port {endpoint {data-lanes = <1 2>;remote-endpoint = <0>;link-frequencies = /bits/ 64 <210000000 168000000>;};};- };
+};
+&i2c5 {
- clock-frequency = <400000>;
- status = "okay";
- accelerometer@18 {
compatible = "silan,sc7a20";reg = <0x18>;interrupt-parent = <&gpio3>;interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;pinctrl-names = "default";pinctrl-0 = <&gsensor_int_l>;st,drdy-int-pin = <1>;vdd-supply = <&vcc_1v8>;vddio-supply = <&vcc_1v8>;mount-matrix = "1", "0", "0","0", "0", "1","0", "1", "0";- };
+};
+&i2s0_8ch {
- status = "okay";
+};
+&i2s1_8ch {
- pinctrl-names = "default";
- pinctrl-0 = <&i2s1m0_sclktx
&i2s1m0_lrcktx&i2s1m0_sdi0&i2s1m0_sdo0>;- rockchip,trcm-sync-tx-only;
- status = "okay";
+};
+&pcie2x1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pcie_reset_h>;
- reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
- vpcie3v3-supply = <&vcc3v3_minipcie>;
- status = "okay";
+};
+&pinctrl {
- camerab {
camerab_pdn_l: camerab-pdn-l {rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;};camerab_rst_l: camerab-rst-l {rockchip,pins = <4 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- cameraf {
cameraf_pdn_l: cameraf-pdn-l {rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;};cameraf_rst_l: cameraf-rst-l {rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- flash {
flash_led_en_h: flash-led-en-h {rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- fspi {
fspi_dual_io_pins: fspi-dual-io-pins {rockchip,pins =/* fspi_clk */<1 RK_PD0 1 &pcfg_pull_none>,/* fspi_cs0n */<1 RK_PD3 1 &pcfg_pull_none>,/* fspi_d0 */<1 RK_PD1 1 &pcfg_pull_none>,/* fspi_d1 */<1 RK_PD2 1 &pcfg_pull_none>;};- };
- gsensor {
gsensor_int_l: gsensor-int-l {rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;};- };
- kb {
kb_id_det: kb-id-det {rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- lcd {
lcd_pwren_h: lcd-pwren-h {rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- pcie {
pcie_pwren_h: pcie-pwren-h {rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;};pcie_reset_h: pcie-reset-h {rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- pmic {
pmic_int_l: pmic-int-l {rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;};- };
- sdmmc {
sdmmc_pwren_l: sdmmc-pwren-l {rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- sound {
hp_det_l: hp-det-l {rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;};spk_ctl: spk-ctl {rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- tp {
tp_int_l_pmuio2: tp-int-l-pmuio2 {rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;};tp_rst_l_pmuio2: tp-rst-l-pmuio2 {rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- usb {
usbcc_int_l: usbcc-int-l {rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;};usb_host_pwren1_h: usb-host-pwren1-h {rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;};usb_host_pwren2_h: usb-host-pwren2-h {rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- wifi {
host_wake_wl: host-wake-wl {rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;};wifi_wake_host_h: wifi-wake-host-h {rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;};- };
+};
+&pmu_io_domains {
- pmuio1-supply = <&vcc3v3_pmu>;
- pmuio2-supply = <&vcca1v8_pmu>;
- vccio1-supply = <&vccio_acodec>;
- vccio2-supply = <&vcc_1v8>;
- vccio3-supply = <&vccio_sd>;
- vccio4-supply = <&vcc_1v8>;
- vccio5-supply = <&vcc_1v8>;
- vccio6-supply = <&vcc1v8_dvp>;
- vccio7-supply = <&vcc_3v3>;
- status = "okay";
+};
+&pwm4 {
- status = "okay";
+};
+&saradc {
- vref-supply = <&vcc_1v8>;
- status = "okay";
+};
+&sdhci {
- bus-width = <8>;
- no-sdio;
- no-sd;
- non-removable;
- max-frequency = <200000000>;
- mmc-hs200-1_8v;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_bus8
&emmc_clk&emmc_cmd&emmc_datastrobe&emmc_rstnout>;- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&vcc_1v8>;
- status = "okay";
+};
+&sdmmc0 {
- bus-width = <4>;
- cap-sd-highspeed;
- cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
- disable-wp;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc0_bus4
&sdmmc0_clk&sdmmc0_cmd&sdmmc0_det>;- sd-uhs-sdr104;
- vmmc-supply = <&vcc3v3_sd>;
- vqmmc-supply = <&vccio_sd>;
- status = "okay";
+};
+&sdmmc1 {
- bus-width = <4>;
- cap-sd-highspeed;
- cap-sdio-irq;
- keep-power-in-suspend;
- non-removable;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc1_bus4
&sdmmc1_cmd&sdmmc1_clk>;- sd-uhs-sdr104;
- vqmmc-supply = <&vcca1v8_pmu>;
- status = "okay";
+};
+&sfc {
- pinctrl-names = "default";
- pinctrl-0 = <&fspi_dual_io_pins>;
- status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
- flash@0 {
compatible = "jedec,spi-nor";reg = <0>;spi-max-frequency = <100000000>;spi-rx-bus-width = <2>;spi-tx-bus-width = <1>;- };
+};
+&tsadc {
- rockchip,hw-tshut-mode = <1>;
- rockchip,hw-tshut-polarity = <0>;
- status = "okay";
+};
+&uart2 {
- status = "okay";
+};
+&usb_host0_ehci {
- status = "okay";
+};
+&usb_host0_ohci {
- status = "okay";
+};
+&usb_host0_xhci {
- status = "okay";
+};
+&usb_host1_xhci {
- status = "okay";
+};
+&usb2phy0 {
- status = "okay";
+};
+&usb2phy0_host {
- phy-supply = <&vcc5v0_usb_host0>;
- status = "okay";
+};
+&usb2phy0_otg {
- status = "okay";
+};
+&usb2phy1 {
- status = "okay";
+};
+&usb2phy1_otg {
- phy-supply = <&vcc5v0_usb_host2>;
- status = "okay";
+};
+&vop {
- assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
- assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
- status = "okay";
+};
+&vop_mmu {
- status = "okay";
+};
+&vp0 {
- vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
reg = <ROCKCHIP_VOP2_EP_HDMI0>;remote-endpoint = <&hdmi_in_vp0>;- };
+};
+&vp1 {
- vp1_out_dsi0: endpoint@ROCKCHIP_VOP2_EP_MIPI0 {
reg = <ROCKCHIP_VOP2_EP_MIPI0>;remote-endpoint = <&dsi0_in_vp1>;- };
+}; diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS index 6b75b35a1243..37b8c1eb78b6 100644 --- a/board/pine64/quartz64_rk3566/MAINTAINERS +++ b/board/pine64/quartz64_rk3566/MAINTAINERS @@ -21,3 +21,14 @@ F: arch/arm/dts/rk3566-soquartz-cm4.dts F: arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi F: arch/arm/dts/rk3566-soquartz-model-a.dts F: arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
+PINETAB2-RK3566 +M: Jonas Karlman jonas@kwiboo.se +S: Maintained +F: configs/pinetab2-rk3566_defconfig +F: arch/arm/dts/rk3566-pinetab2.dtsi +F: arch/arm/dts/rk3566-pinetab2-u-boot.dtsi +F: arch/arm/dts/rk3566-pinetab2-v0.1.dts +F: arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi +F: arch/arm/dts/rk3566-pinetab2-v2.0.dts +F: arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi diff --git a/configs/pinetab2-rk3566_defconfig b/configs/pinetab2-rk3566_defconfig new file mode 100644 index 000000000000..19b396eef975 --- /dev/null +++ b/configs/pinetab2-rk3566_defconfig @@ -0,0 +1,119 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_GPIO=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x1000 +CONFIG_DEFAULT_DEVICE_TREE="rk3566-pinetab2-v2.0" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y +CONFIG_ROCKCHIP_SPI_IMAGE=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_TARGET_QUARTZ64_RK3566=y +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-pinetab2-v2.0.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_I2C=y +CONFIG_SPL_POWER=y +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_POWEROFF=y +CONFIG_CMD_USB=y +CONFIG_CMD_ROCKUSB=y +CONFIG_CMD_USB_MASS_STORAGE=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_OF_LIST="rk3566-pinetab2-v0.1 rk3566-pinetab2-v2.0" +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_BUTTON=y +CONFIG_BUTTON_ADC=y +CONFIG_BUTTON_GPIO=y +CONFIG_SPL_CLK=y +# CONFIG_USB_FUNCTION_FASTBOOT is not set +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_SF_DEFAULT_BUS=4 +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_SILICONKAISER=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_SPL_PMIC_RK8XX=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_SPL_DM_REGULATOR_FIXED=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_ROCKCHIP_SFC=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_PSCI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_ETHER_ASIX88179=y +CONFIG_USB_ETHER_RTL8152=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_PRODUCT_NUM=0x350a +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_FUNCTION_ROCKUSB=y +CONFIG_ERRNO_STR=y diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst index 9fe69fc9422f..fda2282b2c26 100644 --- a/doc/board/rockchip/rockchip.rst +++ b/doc/board/rockchip/rockchip.rst @@ -93,6 +93,7 @@ List of mainline supported Rockchip boards:
- rk3566
- Anbernic RGxx3 (anbernic-rgxx3-rk3566)
- Pine64 PineTab2 (pinetab2-rk3566) - Pine64 Quartz64-A Board (quartz64-a-rk3566) - Pine64 Quartz64-B Board (quartz64-b-rk3566) - Pine64 SOQuartz on Blade (soquartz-blade-rk3566)
Hi Kever,
On 2024-02-05 08:04, Kever Yang wrote:
Hi Jonas,
On 2024/2/5 01:30, Jonas Karlman wrote:
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566 SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64, commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64 PineTab2").
Signed-off-by: Jonas Karlman jonas@kwiboo.se
This patch depend on the series "rockchip: rk35xx: Sync device tree with linux v6.8-rc1" [1].
[1] https://patchwork.ozlabs.org/cover/1891669/
arch/arm/dts/Makefile | 2 + arch/arm/dts/rk3566-pinetab2-u-boot.dtsi | 44 + arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v0.1.dts | 28 +
Does this v0.1 version dts really needed? This seems like a test version instead of release version hardware?
The initial v0.1 was sent out to community developers and v2.0 is the production version sold, so both versions exists in the wild.
In current state they could probably share a single DT for U-Boot usage but in future if panel support is added to U-Boot the two versions does differ a little bit.
Was safer to just include both device trees.
Regards, Jonas
Thanks,
- Kever
arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v2.0.dts | 48 + arch/arm/dts/rk3566-pinetab2.dtsi | 943 ++++++++++++++++++ board/pine64/quartz64_rk3566/MAINTAINERS | 11 + configs/pinetab2-rk3566_defconfig | 119 +++ doc/board/rockchip/rockchip.rst | 1 + 10 files changed, 1202 insertions(+) create mode 100644 arch/arm/dts/rk3566-pinetab2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1.dts create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0.dts create mode 100644 arch/arm/dts/rk3566-pinetab2.dtsi create mode 100644 configs/pinetab2-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 50f35e3db3f0..825fa1cd368a 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -173,6 +173,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3566-anbernic-rgxx3.dtb \
- rk3566-pinetab2-v0.1.dtb \
- rk3566-pinetab2-v2.0.dtb \ rk3566-quartz64-a.dtb \ rk3566-quartz64-b.dtb \ rk3566-radxa-cm3-io.dtb \
diff --git a/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi new file mode 100644 index 000000000000..4aa6ab1c848c --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi @@ -0,0 +1,44 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk356x-u-boot.dtsi"
+&fspi_dual_io_pins {
- bootph-all;
+};
+&gpio0 {
- bootph-all;
+};
+&i2c0 {
- bootph-pre-ram;
+};
+&rk817 {
- bootph-pre-ram;
- regulators {
bootph-pre-ram;- };
+};
+&sdhci {
- cap-mmc-highspeed;
+};
+&sdmmc_pwren_l {
- bootph-all;
+};
+&sfc {
- bootph-pre-ram;
- u-boot,spl-sfc-no-dma;
- flash@0 {
bootph-pre-ram;- };
+};
+&vcc3v3_sd {
- bootph-pre-ram;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1.dts b/arch/arm/dts/rk3566-pinetab2-v0.1.dts new file mode 100644 index 000000000000..5fe6ca5da9d3 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1.dts @@ -0,0 +1,28 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "rk3566-pinetab2.dtsi"
+/ {
- model = "Pine64 PineTab2 v0.1";
- compatible = "pine64,pinetab2-v0.1", "pine64,pinetab2", "rockchip,rk3566";
+};
+&lcd {
- reset-gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+&pinctrl {
- lcd0 {
lcd0_rst_l: lcd0-rst-l {rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
+};
+&sdmmc1 {
- vmmc-supply = <&vcc3v3_sys>;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0.dts b/arch/arm/dts/rk3566-pinetab2-v2.0.dts new file mode 100644 index 000000000000..9349541cbbd0 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0.dts @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "rk3566-pinetab2.dtsi"
+/ {
- model = "Pine64 PineTab2 v2.0";
- compatible = "pine64,pinetab2-v2.0", "pine64,pinetab2", "rockchip,rk3566";
+};
+&gpio_keys {
- pinctrl-0 = <&kb_id_det>, <&hall_int_l>;
- event-hall-sensor {
debounce-interval = <20>;gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;label = "Hall Sensor";linux,code = <SW_LID>;linux,input-type = <EV_SW>;wakeup-event-action = <EV_ACT_DEASSERTED>;wakeup-source;- };
+};
+&lcd {
- reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+&pinctrl {
- lcd0 {
lcd0_rst_l: lcd0-rst-l {rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- hall {
hall_int_l: hall-int-l {rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
+};
+&sdmmc1 {
- vmmc-supply = <&vcc_sys>;
+};
[snip]
On 2024/2/5 01:30, Jonas Karlman wrote:
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566 SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64, commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64 PineTab2").
Signed-off-by: Jonas Karlman jonas@kwiboo.se
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
This patch depend on the series "rockchip: rk35xx: Sync device tree with linux v6.8-rc1" [1].
[1] https://patchwork.ozlabs.org/cover/1891669/
arch/arm/dts/Makefile | 2 + arch/arm/dts/rk3566-pinetab2-u-boot.dtsi | 44 + arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v0.1.dts | 28 + arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v2.0.dts | 48 + arch/arm/dts/rk3566-pinetab2.dtsi | 943 ++++++++++++++++++ board/pine64/quartz64_rk3566/MAINTAINERS | 11 + configs/pinetab2-rk3566_defconfig | 119 +++ doc/board/rockchip/rockchip.rst | 1 + 10 files changed, 1202 insertions(+) create mode 100644 arch/arm/dts/rk3566-pinetab2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1.dts create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0.dts create mode 100644 arch/arm/dts/rk3566-pinetab2.dtsi create mode 100644 configs/pinetab2-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 50f35e3db3f0..825fa1cd368a 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -173,6 +173,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3566-anbernic-rgxx3.dtb \
- rk3566-pinetab2-v0.1.dtb \
- rk3566-pinetab2-v2.0.dtb \ rk3566-quartz64-a.dtb \ rk3566-quartz64-b.dtb \ rk3566-radxa-cm3-io.dtb \
diff --git a/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi new file mode 100644 index 000000000000..4aa6ab1c848c --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-u-boot.dtsi @@ -0,0 +1,44 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk356x-u-boot.dtsi"
+&fspi_dual_io_pins {
- bootph-all;
+};
+&gpio0 {
- bootph-all;
+};
+&i2c0 {
- bootph-pre-ram;
+};
+&rk817 {
- bootph-pre-ram;
- regulators {
bootph-pre-ram;- };
+};
+&sdhci {
- cap-mmc-highspeed;
+};
+&sdmmc_pwren_l {
- bootph-all;
+};
+&sfc {
- bootph-pre-ram;
- u-boot,spl-sfc-no-dma;
- flash@0 {
bootph-pre-ram;- };
+};
+&vcc3v3_sd {
- bootph-pre-ram;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v0.1.dts b/arch/arm/dts/rk3566-pinetab2-v0.1.dts new file mode 100644 index 000000000000..5fe6ca5da9d3 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v0.1.dts @@ -0,0 +1,28 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "rk3566-pinetab2.dtsi"
+/ {
- model = "Pine64 PineTab2 v0.1";
- compatible = "pine64,pinetab2-v0.1", "pine64,pinetab2", "rockchip,rk3566";
+};
+&lcd {
- reset-gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+&pinctrl {
- lcd0 {
lcd0_rst_l: lcd0-rst-l {rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
+};
+&sdmmc1 {
- vmmc-supply = <&vcc3v3_sys>;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi new file mode 100644 index 000000000000..061dc3c2c375 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi @@ -0,0 +1,3 @@ +// SPDX-License-Identifier: GPL-2.0+
+#include "rk3566-pinetab2-u-boot.dtsi" diff --git a/arch/arm/dts/rk3566-pinetab2-v2.0.dts b/arch/arm/dts/rk3566-pinetab2-v2.0.dts new file mode 100644 index 000000000000..9349541cbbd0 --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2-v2.0.dts @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "rk3566-pinetab2.dtsi"
+/ {
- model = "Pine64 PineTab2 v2.0";
- compatible = "pine64,pinetab2-v2.0", "pine64,pinetab2", "rockchip,rk3566";
+};
+&gpio_keys {
- pinctrl-0 = <&kb_id_det>, <&hall_int_l>;
- event-hall-sensor {
debounce-interval = <20>;gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;label = "Hall Sensor";linux,code = <SW_LID>;linux,input-type = <EV_SW>;wakeup-event-action = <EV_ACT_DEASSERTED>;wakeup-source;- };
+};
+&lcd {
- reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+&pinctrl {
- lcd0 {
lcd0_rst_l: lcd0-rst-l {rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- hall {
hall_int_l: hall-int-l {rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;};- };
+};
+&sdmmc1 {
- vmmc-supply = <&vcc_sys>;
+}; diff --git a/arch/arm/dts/rk3566-pinetab2.dtsi b/arch/arm/dts/rk3566-pinetab2.dtsi new file mode 100644 index 000000000000..db40281eafbe --- /dev/null +++ b/arch/arm/dts/rk3566-pinetab2.dtsi @@ -0,0 +1,943 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,vop2.h> +#include <dt-bindings/usb/pd.h> +#include "rk3566.dtsi"
+/ {
- chassis-type = "tablet";
- aliases {
mmc0 = &sdhci;mmc1 = &sdmmc0;- };
- chosen {
stdout-path = "serial2:1500000n8";- };
- adc-keys {
compatible = "adc-keys";io-channels = <&saradc 0>;io-channel-names = "buttons";keyup-threshold-microvolt = <1800000>;poll-interval = <25>;button-vol-up {label = "Volume Up";linux,code = <KEY_VOLUMEUP>;press-threshold-microvolt = <297500>;};button-vol-down {label = "Volume Down";linux,code = <KEY_VOLUMEDOWN>;press-threshold-microvolt = <1750>;};- };
- backlight: backlight {
compatible = "pwm-backlight";pwms = <&pwm4 0 25000 0>;brightness-levels = <20 220>;num-interpolated-steps = <200>;default-brightness-level = <100>;power-supply = <&vcc_sys>;- };
- battery: battery {
compatible = "simple-battery";charge-full-design-microamp-hours = <6000000>;charge-term-current-microamp = <300000>;constant-charge-current-max-microamp = <2000000>;constant-charge-voltage-max-microvolt = <4300000>;voltage-max-design-microvolt = <4350000>;voltage-min-design-microvolt = <3400000>;ocv-capacity-celsius = <20>;ocv-capacity-table-0 = <4322000 100>, <4250000 95>, <4192000 90>, <4136000 85>,<4080000 80>, <4022000 75>, <3972000 70>, <3928000 65>,<3885000 60>, <3833000 55>, <3798000 50>, <3780000 45>,<3776000 40>, <3773000 35>, <3755000 30>, <3706000 25>,<3640000 20>, <3589000 15>, <3535000 10>, <3492000 5>,<3400000 0>;- };
- gpio_keys: gpio-keys {
compatible = "gpio-keys";pinctrl-names = "default";pinctrl-0 = <&kb_id_det>;tablet-mode-switch {debounce-interval = <20>;gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;label = "Tablet Mode";linux,input-type = <EV_SW>;linux,code = <SW_TABLET_MODE>;};- };
- hdmi-connector {
compatible = "hdmi-connector";type = "d";port {hdmi_con_in: endpoint {remote-endpoint = <&hdmi_out_con>;};};- };
- led-0 {
compatible = "regulator-led";vled-supply = <&vcc5v0_flashled>;color = <LED_COLOR_ID_WHITE>;function = LED_FUNCTION_FLASH;- };
- rk817-sound {
compatible = "simple-audio-card";pinctrl-names = "default";pinctrl-0 = <&hp_det_l>;simple-audio-card,format = "i2s";simple-audio-card,name = "rk817_ext";simple-audio-card,mclk-fs = <256>;simple-audio-card,widgets ="Microphone", "Mic Jack","Headphone", "Headphones","Speaker", "Internal Speakers";simple-audio-card,routing ="MICR", "Mic Jack","Headphones", "HPOL","Headphones", "HPOR","Internal Speakers", "Speaker Amplifier OUTL","Internal Speakers", "Speaker Amplifier OUTR","Speaker Amplifier INL", "HPOL","Speaker Amplifier INR", "HPOR";simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;simple-audio-card,aux-devs = <&speaker_amp>;simple-audio-card,pin-switches = "Internal Speakers";simple-audio-card,cpu {sound-dai = <&i2s1_8ch>;};simple-audio-card,codec {sound-dai = <&rk817>;};- };
- speaker_amp: speaker-amplifier {
compatible = "simple-audio-amplifier";pinctrl-names = "default";pinctrl-0 = <&spk_ctl>;enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;sound-name-prefix = "Speaker Amplifier";VCC-supply = <&vcc_bat>;- };
- vcc_3v3: vcc-3v3-regulator {
compatible = "regulator-fixed";regulator-name = "vcc_3v3";regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;vin-supply = <&vcc3v3_sys>;- };
- vcc3v3_minipcie: vcc3v3-minipcie-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&pcie_pwren_h>;regulator-name = "vcc3v3_minipcie";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;vin-supply = <&vcc_sys>;- };
- vcc3v3_sd: vcc3v3-sd-regulator {
compatible = "regulator-fixed";gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&sdmmc_pwren_l>;regulator-name = "vcc3v3_sd";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;vin-supply = <&vcc3v3_sys>;- };
- vcc5v0_flashled: vcc5v0-flashled-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&flash_led_en_h>;regulator-name = "vcc5v0_flashled";regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;vin-supply = <&vcc5v_midu>;- };
- vcc5v0_usb_host0: vcc5v0-usb-host0-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&usb_host_pwren1_h>;regulator-name = "vcc5v0_usb_host0";regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;vin-supply = <&vcc5v_midu>;- };
- vcc5v0_usb_host2: vcc5v0-usb-host2-regulator {
compatible = "regulator-fixed";enable-active-high;gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;pinctrl-names = "default";pinctrl-0 = <&usb_host_pwren2_h>;regulator-name = "vcc5v0_usb_host2";regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;vin-supply = <&vcc5v_midu>;- };
- vcc_bat: vcc-bat-regulator {
compatible = "regulator-fixed";regulator-name = "vcc_bat";regulator-always-on;regulator-boot-on;- };
- vcc_sys: vcc-sys-regulator {
compatible = "regulator-fixed";regulator-name = "vcc_sys";regulator-always-on;regulator-boot-on;vin-supply = <&vcc_bat>;- };
- vdd1v2_dvp: vdd1v2-dvp-regulator {
compatible = "regulator-fixed";regulator-name = "vdd1v2_dvp";regulator-min-microvolt = <1200000>;regulator-max-microvolt = <1200000>;vin-supply = <&vcc_3v3>;- };
+};
+&combphy1 {
- status = "okay";
+};
+&combphy2 {
- status = "okay";
+};
+&cpu0 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu1 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu2 {
- cpu-supply = <&vdd_cpu>;
+};
+&cpu3 {
- cpu-supply = <&vdd_cpu>;
+};
+&cru {
- assigned-clocks = <&pmucru CLK_RTC_32K>, <&cru PLL_GPLL>,
<&pmucru PLL_PPLL>, <&cru PLL_VPLL>;- assigned-clock-rates = <32768>, <1200000000>, <200000000>, <500000000>;
- assigned-clock-parents = <&pmucru CLK_RTC32K_FRAC>;
+};
+&csi_dphy {
- status = "okay";
+};
+&dsi0 {
- status = "okay";
- clock-master;
- #address-cells = <1>;
- #size-cells = <0>;
- lcd: panel@0 {
compatible = "boe,th101mb31ig002-28a";reg = <0>;backlight = <&backlight>;enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;rotation = <90>;power-supply = <&vcc_3v3>;port@0 {panel_in_dsi: endpoint@0 {remote-endpoint = <&dsi0_out_con>;};};- };
+};
+&dsi0_in {
- dsi0_in_vp1: endpoint {
remote-endpoint = <&vp1_out_dsi0>;- };
+};
+&dsi0_out {
- dsi0_out_con: endpoint {
remote-endpoint = <&panel_in_dsi>;- };
+};
+&dsi_dphy0 {
- status = "okay";
+};
+&gpu {
- mali-supply = <&vdd_gpu_npu>;
- status = "okay";
+};
+&hdmi {
- avdd-0v9-supply = <&vdda_0v9_p>;
- avdd-1v8-supply = <&vcc_1v8>;
- status = "okay";
+};
+&hdmi_in {
- hdmi_in_vp0: endpoint {
remote-endpoint = <&vp0_out_hdmi>;- };
+};
+&hdmi_out {
- hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;- };
+};
+&hdmi_sound {
- status = "okay";
+};
+&i2c0 {
- clock-frequency = <400000>;
- status = "okay";
- vdd_cpu: regulator@1c {
compatible = "tcs,tcs4525";reg = <0x1c>;fcs,suspend-voltage-selector = <1>;regulator-name = "vdd_cpu";regulator-min-microvolt = <800000>;regulator-max-microvolt = <1150000>;regulator-ramp-delay = <2300>;regulator-always-on;regulator-boot-on;vin-supply = <&vcc_sys>;regulator-state-mem {regulator-off-in-suspend;};- };
- rk817: pmic@20 {
compatible = "rockchip,rk817";reg = <0x20>;interrupt-parent = <&gpio0>;interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;assigned-clocks = <&cru I2S1_MCLKOUT_TX>;assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;clock-names = "mclk";clocks = <&cru I2S1_MCLKOUT_TX>;clock-output-names = "rk808-clkout1", "rk808-clkout2";#clock-cells = <1>;pinctrl-names = "default";pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;rockchip,system-power-controller;#sound-dai-cells = <0>;wakeup-source;vcc1-supply = <&vcc_sys>;vcc2-supply = <&vcc_sys>;vcc3-supply = <&vcc_sys>;vcc4-supply = <&vcc_sys>;vcc5-supply = <&vcc_sys>;vcc6-supply = <&vcc_sys>;vcc7-supply = <&vcc_sys>;vcc8-supply = <&vcc_sys>;vcc9-supply = <&vcc5v_midu>;regulators {vdd_logic: DCDC_REG1 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <500000>;regulator-max-microvolt = <1350000>;regulator-ramp-delay = <6001>;regulator-initial-mode = <0x2>;regulator-name = "vdd_logic";regulator-state-mem {regulator-off-in-suspend;};};vdd_gpu_npu: DCDC_REG2 {regulator-min-microvolt = <500000>;regulator-max-microvolt = <1350000>;regulator-ramp-delay = <6001>;regulator-initial-mode = <0x2>;regulator-name = "vdd_gpu_npu";regulator-state-mem {regulator-off-in-suspend;};};vcc_ddr: DCDC_REG3 {regulator-always-on;regulator-boot-on;regulator-initial-mode = <0x2>;regulator-name = "vcc_ddr";regulator-state-mem {regulator-on-in-suspend;};};vcc3v3_sys: DCDC_REG4 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-initial-mode = <0x2>;regulator-name = "vcc3v3_sys";regulator-state-mem {regulator-off-in-suspend;};};vcca1v8_pmu: LDO_REG1 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-name = "vcca1v8_pmu";regulator-state-mem {regulator-on-in-suspend;};};vdda_0v9_p: LDO_REG2 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <900000>;regulator-max-microvolt = <900000>;regulator-name = "vdda_0v9_p";regulator-state-mem {regulator-off-in-suspend;};};vdda0v9_pmu: LDO_REG3 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <900000>;regulator-max-microvolt = <900000>;regulator-name = "vdda0v9_pmu";regulator-state-mem {regulator-on-in-suspend;};};vccio_acodec: LDO_REG4 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-name = "vccio_acodec";regulator-state-mem {regulator-off-in-suspend;};};vccio_sd: LDO_REG5 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <3300000>;regulator-name = "vccio_sd";regulator-state-mem {regulator-off-in-suspend;};};vcc3v3_pmu: LDO_REG6 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;regulator-name = "vcc3v3_pmu";regulator-state-mem {regulator-on-in-suspend;};};vcc_1v8: LDO_REG7 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-name = "vcc_1v8";regulator-state-mem {regulator-off-in-suspend;};};vcc1v8_dvp: LDO_REG8 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;regulator-name = "vcc1v8_dvp";regulator-state-mem {regulator-off-in-suspend;};};vcc2v8_dvp: LDO_REG9 {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <2800000>;regulator-max-microvolt = <2800000>;regulator-name = "vcc2v8_dvp";regulator-state-mem {regulator-off-in-suspend;};};vcc5v_midu: BOOST {regulator-always-on;regulator-boot-on;regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;regulator-name = "boost";regulator-state-mem {regulator-off-in-suspend;};};vbus: OTG_SWITCH {regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;regulator-name = "otg_switch";regulator-state-mem {regulator-off-in-suspend;};};};charger {monitored-battery = <&battery>;rockchip,resistor-sense-micro-ohms = <10000>;rockchip,sleep-enter-current-microamp = <300000>;rockchip,sleep-filter-current-microamp = <100000>;};- };
+};
+&i2c1 {
- clock-frequency = <400000>;
- status = "okay";
- touchscreen@5d {
compatible = "goodix,gt911";reg = <0x5d>;interrupt-parent = <&gpio0>;interrupts = <RK_PB0 IRQ_TYPE_EDGE_FALLING>;pinctrl-names = "default";pinctrl-0 = <&tp_int_l_pmuio2>, <&tp_rst_l_pmuio2>;AVDD28-supply = <&vcc3v3_pmu>;VDDIO-supply = <&vcca1v8_pmu>;irq-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;reset-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;- };
+};
+&i2c2 {
- clock-frequency = <400000>;
- pinctrl-0 = <&i2c2m1_xfer>;
- status = "okay";
- vcm@c {
compatible = "dongwoon,dw9714";reg = <0x0c>;vcc-supply = <&vcc1v8_dvp>;- };
- camera@36 {
compatible = "ovti,ov5648";reg = <0x36>;pinctrl-names = "default";pinctrl-0 = <&camerab_pdn_l &camerab_rst_l>;clocks = <&cru CLK_CIF_OUT>;assigned-clocks = <&cru CLK_CIF_OUT>;assigned-clock-rates = <24000000>;avdd-supply = <&vcc2v8_dvp>;dvdd-supply = <&vdd1v2_dvp>;dovdd-supply = <&vcc1v8_dvp>;powerdown-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;reset-gpios = <&gpio4 RK_PB1 GPIO_ACTIVE_LOW>;port {endpoint {data-lanes = <1 2>;remote-endpoint = <0>;link-frequencies = /bits/ 64 <210000000 168000000>;};};- };
+};
+&i2c5 {
- clock-frequency = <400000>;
- status = "okay";
- accelerometer@18 {
compatible = "silan,sc7a20";reg = <0x18>;interrupt-parent = <&gpio3>;interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;pinctrl-names = "default";pinctrl-0 = <&gsensor_int_l>;st,drdy-int-pin = <1>;vdd-supply = <&vcc_1v8>;vddio-supply = <&vcc_1v8>;mount-matrix = "1", "0", "0","0", "0", "1","0", "1", "0";- };
+};
+&i2s0_8ch {
- status = "okay";
+};
+&i2s1_8ch {
- pinctrl-names = "default";
- pinctrl-0 = <&i2s1m0_sclktx
&i2s1m0_lrcktx&i2s1m0_sdi0&i2s1m0_sdo0>;- rockchip,trcm-sync-tx-only;
- status = "okay";
+};
+&pcie2x1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pcie_reset_h>;
- reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
- vpcie3v3-supply = <&vcc3v3_minipcie>;
- status = "okay";
+};
+&pinctrl {
- camerab {
camerab_pdn_l: camerab-pdn-l {rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;};camerab_rst_l: camerab-rst-l {rockchip,pins = <4 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- cameraf {
cameraf_pdn_l: cameraf-pdn-l {rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;};cameraf_rst_l: cameraf-rst-l {rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- flash {
flash_led_en_h: flash-led-en-h {rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- fspi {
fspi_dual_io_pins: fspi-dual-io-pins {rockchip,pins =/* fspi_clk */<1 RK_PD0 1 &pcfg_pull_none>,/* fspi_cs0n */<1 RK_PD3 1 &pcfg_pull_none>,/* fspi_d0 */<1 RK_PD1 1 &pcfg_pull_none>,/* fspi_d1 */<1 RK_PD2 1 &pcfg_pull_none>;};- };
- gsensor {
gsensor_int_l: gsensor-int-l {rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;};- };
- kb {
kb_id_det: kb-id-det {rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- lcd {
lcd_pwren_h: lcd-pwren-h {rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- pcie {
pcie_pwren_h: pcie-pwren-h {rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;};pcie_reset_h: pcie-reset-h {rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- pmic {
pmic_int_l: pmic-int-l {rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;};- };
- sdmmc {
sdmmc_pwren_l: sdmmc-pwren-l {rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- sound {
hp_det_l: hp-det-l {rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;};spk_ctl: spk-ctl {rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- tp {
tp_int_l_pmuio2: tp-int-l-pmuio2 {rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;};tp_rst_l_pmuio2: tp-rst-l-pmuio2 {rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- usb {
usbcc_int_l: usbcc-int-l {rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;};usb_host_pwren1_h: usb-host-pwren1-h {rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;};usb_host_pwren2_h: usb-host-pwren2-h {rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;};- };
- wifi {
host_wake_wl: host-wake-wl {rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;};wifi_wake_host_h: wifi-wake-host-h {rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;};- };
+};
+&pmu_io_domains {
- pmuio1-supply = <&vcc3v3_pmu>;
- pmuio2-supply = <&vcca1v8_pmu>;
- vccio1-supply = <&vccio_acodec>;
- vccio2-supply = <&vcc_1v8>;
- vccio3-supply = <&vccio_sd>;
- vccio4-supply = <&vcc_1v8>;
- vccio5-supply = <&vcc_1v8>;
- vccio6-supply = <&vcc1v8_dvp>;
- vccio7-supply = <&vcc_3v3>;
- status = "okay";
+};
+&pwm4 {
- status = "okay";
+};
+&saradc {
- vref-supply = <&vcc_1v8>;
- status = "okay";
+};
+&sdhci {
- bus-width = <8>;
- no-sdio;
- no-sd;
- non-removable;
- max-frequency = <200000000>;
- mmc-hs200-1_8v;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_bus8
&emmc_clk&emmc_cmd&emmc_datastrobe&emmc_rstnout>;- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&vcc_1v8>;
- status = "okay";
+};
+&sdmmc0 {
- bus-width = <4>;
- cap-sd-highspeed;
- cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
- disable-wp;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc0_bus4
&sdmmc0_clk&sdmmc0_cmd&sdmmc0_det>;- sd-uhs-sdr104;
- vmmc-supply = <&vcc3v3_sd>;
- vqmmc-supply = <&vccio_sd>;
- status = "okay";
+};
+&sdmmc1 {
- bus-width = <4>;
- cap-sd-highspeed;
- cap-sdio-irq;
- keep-power-in-suspend;
- non-removable;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc1_bus4
&sdmmc1_cmd&sdmmc1_clk>;- sd-uhs-sdr104;
- vqmmc-supply = <&vcca1v8_pmu>;
- status = "okay";
+};
+&sfc {
- pinctrl-names = "default";
- pinctrl-0 = <&fspi_dual_io_pins>;
- status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
- flash@0 {
compatible = "jedec,spi-nor";reg = <0>;spi-max-frequency = <100000000>;spi-rx-bus-width = <2>;spi-tx-bus-width = <1>;- };
+};
+&tsadc {
- rockchip,hw-tshut-mode = <1>;
- rockchip,hw-tshut-polarity = <0>;
- status = "okay";
+};
+&uart2 {
- status = "okay";
+};
+&usb_host0_ehci {
- status = "okay";
+};
+&usb_host0_ohci {
- status = "okay";
+};
+&usb_host0_xhci {
- status = "okay";
+};
+&usb_host1_xhci {
- status = "okay";
+};
+&usb2phy0 {
- status = "okay";
+};
+&usb2phy0_host {
- phy-supply = <&vcc5v0_usb_host0>;
- status = "okay";
+};
+&usb2phy0_otg {
- status = "okay";
+};
+&usb2phy1 {
- status = "okay";
+};
+&usb2phy1_otg {
- phy-supply = <&vcc5v0_usb_host2>;
- status = "okay";
+};
+&vop {
- assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
- assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
- status = "okay";
+};
+&vop_mmu {
- status = "okay";
+};
+&vp0 {
- vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
reg = <ROCKCHIP_VOP2_EP_HDMI0>;remote-endpoint = <&hdmi_in_vp0>;- };
+};
+&vp1 {
- vp1_out_dsi0: endpoint@ROCKCHIP_VOP2_EP_MIPI0 {
reg = <ROCKCHIP_VOP2_EP_MIPI0>;remote-endpoint = <&dsi0_in_vp1>;- };
+}; diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS index 6b75b35a1243..37b8c1eb78b6 100644 --- a/board/pine64/quartz64_rk3566/MAINTAINERS +++ b/board/pine64/quartz64_rk3566/MAINTAINERS @@ -21,3 +21,14 @@ F: arch/arm/dts/rk3566-soquartz-cm4.dts F: arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi F: arch/arm/dts/rk3566-soquartz-model-a.dts F: arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
+PINETAB2-RK3566 +M: Jonas Karlman jonas@kwiboo.se +S: Maintained +F: configs/pinetab2-rk3566_defconfig +F: arch/arm/dts/rk3566-pinetab2.dtsi +F: arch/arm/dts/rk3566-pinetab2-u-boot.dtsi +F: arch/arm/dts/rk3566-pinetab2-v0.1.dts +F: arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi +F: arch/arm/dts/rk3566-pinetab2-v2.0.dts +F: arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi diff --git a/configs/pinetab2-rk3566_defconfig b/configs/pinetab2-rk3566_defconfig new file mode 100644 index 000000000000..19b396eef975 --- /dev/null +++ b/configs/pinetab2-rk3566_defconfig @@ -0,0 +1,119 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_GPIO=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x1000 +CONFIG_DEFAULT_DEVICE_TREE="rk3566-pinetab2-v2.0" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y +CONFIG_ROCKCHIP_SPI_IMAGE=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_TARGET_QUARTZ64_RK3566=y +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-pinetab2-v2.0.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_I2C=y +CONFIG_SPL_POWER=y +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_POWEROFF=y +CONFIG_CMD_USB=y +CONFIG_CMD_ROCKUSB=y +CONFIG_CMD_USB_MASS_STORAGE=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_OF_LIST="rk3566-pinetab2-v0.1 rk3566-pinetab2-v2.0" +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_BUTTON=y +CONFIG_BUTTON_ADC=y +CONFIG_BUTTON_GPIO=y +CONFIG_SPL_CLK=y +# CONFIG_USB_FUNCTION_FASTBOOT is not set +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_SF_DEFAULT_BUS=4 +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_SILICONKAISER=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_SPL_PMIC_RK8XX=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_SPL_DM_REGULATOR_FIXED=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_ROCKCHIP_SFC=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_PSCI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_ETHER_ASIX88179=y +CONFIG_USB_ETHER_RTL8152=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_PRODUCT_NUM=0x350a +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_FUNCTION_ROCKUSB=y +CONFIG_ERRNO_STR=y diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst index 9fe69fc9422f..fda2282b2c26 100644 --- a/doc/board/rockchip/rockchip.rst +++ b/doc/board/rockchip/rockchip.rst @@ -93,6 +93,7 @@ List of mainline supported Rockchip boards:
- rk3566
- Anbernic RGxx3 (anbernic-rgxx3-rk3566)
- Pine64 PineTab2 (pinetab2-rk3566) - Pine64 Quartz64-A Board (quartz64-a-rk3566) - Pine64 Quartz64-B Board (quartz64-b-rk3566) - Pine64 SOQuartz on Blade (soquartz-blade-rk3566)
Hi Kever,
On 2024-03-14 07:50, Kever Yang wrote:
On 2024/2/5 01:30, Jonas Karlman wrote:
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566 SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64, commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64 PineTab2").
Signed-off-by: Jonas Karlman jonas@kwiboo.se
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, I will send a v2 with small adjustments to bootph flags used in board u-boot.dtsi and update defconfig to take advantage of the new ROCKCHIP_COMMON_STACK_ADDR bss and stack addresses.
Regards, Jonas
Thanks,
- Kever
This patch depend on the series "rockchip: rk35xx: Sync device tree with linux v6.8-rc1" [1].
[1] https://patchwork.ozlabs.org/cover/1891669/
arch/arm/dts/Makefile | 2 + arch/arm/dts/rk3566-pinetab2-u-boot.dtsi | 44 + arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v0.1.dts | 28 + arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi | 3 + arch/arm/dts/rk3566-pinetab2-v2.0.dts | 48 + arch/arm/dts/rk3566-pinetab2.dtsi | 943 ++++++++++++++++++ board/pine64/quartz64_rk3566/MAINTAINERS | 11 + configs/pinetab2-rk3566_defconfig | 119 +++ doc/board/rockchip/rockchip.rst | 1 + 10 files changed, 1202 insertions(+) create mode 100644 arch/arm/dts/rk3566-pinetab2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v0.1.dts create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-pinetab2-v2.0.dts create mode 100644 arch/arm/dts/rk3566-pinetab2.dtsi create mode 100644 configs/pinetab2-rk3566_defconfig
[snip]
participants (2)
-
Jonas Karlman -
Kever Yang