Add Atmel sama5d3 SoC new pmc register

Signed-off-by: Bo Shen voice.shen@atmel.com --- Changes in v3: - New splitted patch file.

Changes in v2: - No change

arch/arm/include/asm/arch-at91/at91_pmc.h | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)

diff --git a/arch/arm/include/asm/arch-at91/at91_pmc.h b/arch/arm/include/asm/arch-at91/at91_pmc.h index 086cb9b..66075b4 100644 --- a/arch/arm/include/asm/arch-at91/at91_pmc.h +++ b/arch/arm/include/asm/arch-at91/at91_pmc.h @@ -55,7 +55,16 @@ typedef struct at91_pmc { u32 reserved5[21]; u32 wpmr; /* 0xE4 Write Protect Mode Register (CAP0) */ u32 wpsr; /* 0xE8 Write Protect Status Register (CAP0) */ +#ifdef CONFIG_SAMA5D3 + u32 reserved6[8]; + u32 pcer1; /* 0x100 Periperial Clock Enable Register 1 */ + u32 pcdr1; /* 0x104 Periperial Clock Disable Register 1 */ + u32 pcsr1; /* 0x108 Periperial Clock Status Register 1 */ + u32 pcr; /* 0x10c Periperial Control Register */ + u32 ocr; /* 0x110 Oscillator Calibration Register */ +#else u32 reserved8[5]; +#endif } at91_pmc_t;

#endif /* end not assembly */ @@ -82,6 +91,16 @@ typedef struct at91_pmc { #define AT91_PMC_MCKR_CSS_PLLB 0x00000003 #define AT91_PMC_MCKR_CSS_MASK 0x00000003

+#ifdef CONFIG_SAMA5D3 +#define AT91_PMC_MCKR_PRES_1 0x00000000 +#define AT91_PMC_MCKR_PRES_2 0x00000010 +#define AT91_PMC_MCKR_PRES_4 0x00000020 +#define AT91_PMC_MCKR_PRES_8 0x00000030 +#define AT91_PMC_MCKR_PRES_16 0x00000040 +#define AT91_PMC_MCKR_PRES_32 0x00000050 +#define AT91_PMC_MCKR_PRES_64 0x00000060 +#define AT91_PMC_MCKR_PRES_MASK 0x00000070 +#else #define AT91_PMC_MCKR_PRES_1 0x00000000 #define AT91_PMC_MCKR_PRES_2 0x00000004 #define AT91_PMC_MCKR_PRES_4 0x00000008 @@ -90,6 +109,7 @@ typedef struct at91_pmc { #define AT91_PMC_MCKR_PRES_32 0x00000014 #define AT91_PMC_MCKR_PRES_64 0x00000018 #define AT91_PMC_MCKR_PRES_MASK 0x0000001C +#endif

#ifdef CONFIG_AT91RM9200 #define AT91_PMC_MCKR_MDIV_1 0x00000000 @@ -100,6 +120,9 @@ typedef struct at91_pmc { #else #define AT91_PMC_MCKR_MDIV_1 0x00000000 #define AT91_PMC_MCKR_MDIV_2 0x00000100 +#ifdef CONFIG_SAMA5D3 +#define AT91_PMC_MCKR_MDIV_3 0x00000300 +#endif #define AT91_PMC_MCKR_MDIV_4 0x00000200 #define AT91_PMC_MCKR_MDIV_MASK 0x00000300 #endif

Add sama5d3xek support with following feature - boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector - boot from SPI flash support - boot from SD card support - LCD support - EMAC support - USB OHCI support

Signed-off-by: Bo Shen voice.shen@atmel.com --- Changes in v3: - Split new pmc register in a standalone patch - The EMAC support need: net: macb: using AT91FAMILY replace #ifdeferry - http://patchwork.ozlabs.org/patch/239064/

Changes in v2: - Remove unneeded #undef - Using string directly - Add missed copyright - Using pull up for usart Tx line - Using pull up for spi cs - make code more readable in clock.c file - move LCD higher 8 bit to board file (This is board related)

MAINTAINERS | 1 + arch/arm/cpu/armv7/at91/Makefile | 52 +++++ arch/arm/cpu/armv7/at91/clock.c | 125 ++++++++++++ arch/arm/cpu/armv7/at91/cpu.c | 90 +++++++++ arch/arm/cpu/armv7/at91/reset.c | 47 +++++ arch/arm/cpu/armv7/at91/sama5d3_devices.c | 196 ++++++++++++++++++ arch/arm/cpu/armv7/at91/timer.c | 139 +++++++++++++ arch/arm/include/asm/arch-at91/at91_dbu.h | 4 + arch/arm/include/asm/arch-at91/clk.h | 1 + arch/arm/include/asm/arch-at91/hardware.h | 2 + arch/arm/include/asm/arch-at91/sama5d3.h | 212 ++++++++++++++++++++ arch/arm/include/asm/arch-at91/sama5d3_smc.h | 79 ++++++++ board/atmel/sama5d3xek/Makefile | 51 +++++ board/atmel/sama5d3xek/sama5d3xek.c | 275 ++++++++++++++++++++++++++ boards.cfg | 3 + include/configs/sama5d3xek.h | 245 +++++++++++++++++++++++ 16 files changed, 1522 insertions(+) create mode 100644 arch/arm/cpu/armv7/at91/Makefile create mode 100644 arch/arm/cpu/armv7/at91/clock.c create mode 100644 arch/arm/cpu/armv7/at91/cpu.c create mode 100644 arch/arm/cpu/armv7/at91/reset.c create mode 100644 arch/arm/cpu/armv7/at91/sama5d3_devices.c create mode 100644 arch/arm/cpu/armv7/at91/timer.c create mode 100644 arch/arm/include/asm/arch-at91/sama5d3.h create mode 100644 arch/arm/include/asm/arch-at91/sama5d3_smc.h create mode 100644 board/atmel/sama5d3xek/Makefile create mode 100644 board/atmel/sama5d3xek/sama5d3xek.c create mode 100644 include/configs/sama5d3xek.h

diff --git a/MAINTAINERS b/MAINTAINERS index efc2ecc..2bd0a98 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -918,6 +918,7 @@ Matt Sealey matt@genesi-usa.com

Bo Shen voice.shen@atmel.com at91sam9x5ek ARM926EJS (AT91SAM9G15,G25,G35,X25,X35 SoC) + sama5d3xek ARMV7 (SAMA5D31, D33, D34, D35 SoC)

Rajeshwari Shinde rajeshwari.s@samsung.com

diff --git a/arch/arm/cpu/armv7/at91/Makefile b/arch/arm/cpu/armv7/at91/Makefile new file mode 100644 index 0000000..040c67d --- /dev/null +++ b/arch/arm/cpu/armv7/at91/Makefile @@ -0,0 +1,52 @@ +# +# (C) Copyright 2000-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2013 +# Bo Shen voice.shen@atmel.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(SOC).o + +COBJS-$(CONFIG_SAMA5D3) += sama5d3_devices.o +COBJS-y += clock.o +COBJS-y += cpu.o +COBJS-y += reset.o +COBJS-y += timer.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y)) + +all: $(obj).depend $(LIB) + +$(LIB): $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/arch/arm/cpu/armv7/at91/clock.c b/arch/arm/cpu/armv7/at91/clock.c new file mode 100644 index 0000000..624b52c --- /dev/null +++ b/arch/arm/cpu/armv7/at91/clock.c @@ -0,0 +1,125 @@ +/* + * [origin: Linux kernel linux/arch/arm/mach-at91/clock.c] + * + * Copyright (C) 2005 David Brownell + * Copyright (C) 2005 Ivan Kokshaysky + * Copyright (C) 2009 Jean-Christophe PLAGNIOL-VILLARD plagnioj@jcrosoft.com + * Copyright (C) 2013 Bo Shen voice.shen@atmel.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> + +#if !defined(CONFIG_AT91FAMILY) +# error You need to define CONFIG_AT91FAMILY in your board config! +#endif + +DECLARE_GLOBAL_DATA_PTR; + +static unsigned long at91_css_to_rate(unsigned long css) +{ + switch (css) { + case AT91_PMC_MCKR_CSS_SLOW: + return CONFIG_SYS_AT91_SLOW_CLOCK; + case AT91_PMC_MCKR_CSS_MAIN: + return gd->arch.main_clk_rate_hz; + case AT91_PMC_MCKR_CSS_PLLA: + return gd->arch.plla_rate_hz; + } + + return 0; +} + +static u32 at91_pll_rate(u32 freq, u32 reg) +{ + unsigned mul, div; + + div = reg & 0xff; + mul = (reg >> 18) & 0x7f; + if (div && mul) { + freq /= div; + freq *= mul + 1; + } else { + freq = 0; + } + + return freq; +} + +int at91_clock_init(unsigned long main_clock) +{ + unsigned freq, mckr; + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; +#ifndef CONFIG_SYS_AT91_MAIN_CLOCK + unsigned tmp; + /* + * When the bootloader initialized the main oscillator correctly, + * there's no problem using the cycle counter. But if it didn't, + * or when using oscillator bypass mode, we must be told the speed + * of the main clock. + */ + if (!main_clock) { + do { + tmp = readl(&pmc->mcfr); + } while (!(tmp & AT91_PMC_MCFR_MAINRDY)); + tmp &= AT91_PMC_MCFR_MAINF_MASK; + main_clock = tmp * (CONFIG_SYS_AT91_SLOW_CLOCK / 16); + } +#endif + gd->arch.main_clk_rate_hz = main_clock; + + /* report if PLLA is more than mildly overclocked */ + gd->arch.plla_rate_hz = at91_pll_rate(main_clock, readl(&pmc->pllar)); + + /* + * MCK and CPU derive from one of those primary clocks. + * For now, assume this parentage won't change. + */ + mckr = readl(&pmc->mckr); + + /* plla divisor by 2 */ + if (mckr & (1 << 12)) + gd->arch.plla_rate_hz >>= 1; + + gd->arch.mck_rate_hz = at91_css_to_rate(mckr & AT91_PMC_MCKR_CSS_MASK); + freq = gd->arch.mck_rate_hz; + + /* prescale */ + freq >>= mckr & AT91_PMC_MCKR_PRES_MASK; + + switch (mckr & AT91_PMC_MCKR_MDIV_MASK) { + case AT91_PMC_MCKR_MDIV_2: + gd->arch.mck_rate_hz = freq / 2; + break; + case AT91_PMC_MCKR_MDIV_3: + gd->arch.mck_rate_hz = freq / 3; + break; + case AT91_PMC_MCKR_MDIV_4: + gd->arch.mck_rate_hz = freq / 4; + break; + default: + break; + } + + gd->arch.cpu_clk_rate_hz = freq; + + return 0; +} + +void at91_periph_clk_enable(int id) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + if (id > 31) + writel(1 << (id - 32), &pmc->pcer1); + else + writel(1 << id, &pmc->pcer); +} diff --git a/arch/arm/cpu/armv7/at91/cpu.c b/arch/arm/cpu/armv7/at91/cpu.c new file mode 100644 index 0000000..3df6143 --- /dev/null +++ b/arch/arm/cpu/armv7/at91/cpu.c @@ -0,0 +1,90 @@ +/* + * (C) Copyright 2010 + * Reinhard Meyer, reinhard.meyer@emk-elektronik.de + * (C) Copyright 2009 + * Jean-Christophe PLAGNIOL-VILLARD plagnioj@jcrosoft.com + * (C) Copyright 2013 + * Bo Shen voice.shen@atmel.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_dbu.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_pit.h> +#include <asm/arch/at91_gpbr.h> +#include <asm/arch/clk.h> + +#ifndef CONFIG_SYS_AT91_MAIN_CLOCK +#define CONFIG_SYS_AT91_MAIN_CLOCK 0 +#endif + +int arch_cpu_init(void) +{ + return at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK); +} + +void arch_preboot_os(void) +{ + ulong cpiv; + at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT; + + cpiv = AT91_PIT_MR_PIV_MASK(readl(&pit->piir)); + + /* + * Disable PITC + * Add 0x1000 to current counter to stop it faster + * without waiting for wrapping back to 0 + */ + writel(cpiv + 0x1000, &pit->mr); +} + +#if defined(CONFIG_DISPLAY_CPUINFO) +int print_cpuinfo(void) +{ + char buf[32]; + + printf("CPU: %s\n", get_cpu_name()); + printf("Crystal frequency: %8s MHz\n", + strmhz(buf, get_main_clk_rate())); + printf("CPU clock : %8s MHz\n", + strmhz(buf, get_cpu_clk_rate())); + printf("Master clock : %8s MHz\n", + strmhz(buf, get_mck_clk_rate())); + + return 0; +} +#endif + +void enable_caches(void) +{ +} + +unsigned int get_chip_id(void) +{ + return readl(ATMEL_BASE_DBGU + AT91_DBU_CIDR) & ~AT91_DBU_CIDR_MASK; +} + +unsigned int get_extension_chip_id(void) +{ + return readl(ATMEL_BASE_DBGU + AT91_DBU_EXID); +} diff --git a/arch/arm/cpu/armv7/at91/reset.c b/arch/arm/cpu/armv7/at91/reset.c new file mode 100644 index 0000000..b9f83d9 --- /dev/null +++ b/arch/arm/cpu/armv7/at91/reset.c @@ -0,0 +1,47 @@ +/* + * (C) Copyright 2007-2008 + * Stelian Pop stelian@popies.net + * Lead Tech Design <www.leadtechdesign.com> + * + * (C) Copyright 2013 + * Bo Shen voice.shen@atmel.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_rstc.h> + +/* Reset the cpu by telling the reset controller to do so */ +void reset_cpu(ulong ignored) +{ + at91_rstc_t *rstc = (at91_rstc_t *)ATMEL_BASE_RSTC; + + writel(AT91_RSTC_KEY + | AT91_RSTC_CR_PROCRST /* Processor Reset */ + | AT91_RSTC_CR_PERRST /* Peripheral Reset */ +#ifdef CONFIG_AT91RESET_EXTRST + | AT91_RSTC_CR_EXTRST /* External Reset (assert nRST pin) */ +#endif + , &rstc->cr); + /* never reached */ + do { } while (1); +} diff --git a/arch/arm/cpu/armv7/at91/sama5d3_devices.c b/arch/arm/cpu/armv7/at91/sama5d3_devices.c new file mode 100644 index 0000000..acf8b43 --- /dev/null +++ b/arch/arm/cpu/armv7/at91/sama5d3_devices.c @@ -0,0 +1,196 @@ +/* + * Copyright (C) 2012-2013 Atmel Corporation + * Bo Shen voice.shen@atmel.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/arch/sama5d3.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> +#include <asm/arch/gpio.h> +#include <asm/io.h> + +unsigned int has_emac() +{ + return cpu_is_sama5d31() || cpu_is_sama5d35(); +} + +unsigned int has_gmac() +{ + return !cpu_is_sama5d31(); +} + +unsigned int has_lcdc() +{ + return !cpu_is_sama5d35(); +} + +char *get_cpu_name() +{ + unsigned int extension_id = get_extension_chip_id(); + + if (cpu_is_sama5d3()) + switch (extension_id) { + case ARCH_EXID_SAMA5D31: + return "SAMA5D31"; + case ARCH_EXID_SAMA5D33: + return "SAMA5D33"; + case ARCH_EXID_SAMA5D34: + return "SAMA5D34"; + case ARCH_EXID_SAMA5D35: + return "SAMA5D35"; + default: + return "Unknown CPU type"; + } + else + return "Unknown CPU type"; +} + +void at91_serial0_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTD, 18, 1); /* TXD0 */ + at91_set_a_periph(AT91_PIO_PORTD, 17, 0); /* RXD0 */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_USART0); +} + +void at91_serial1_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTB, 29, 1); /* TXD1 */ + at91_set_a_periph(AT91_PIO_PORTB, 28, 0); /* RXD1 */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_USART1); +} + +void at91_serial2_hw_init(void) +{ + at91_set_b_periph(AT91_PIO_PORTE, 26, 1); /* TXD2 */ + at91_set_b_periph(AT91_PIO_PORTE, 25, 0); /* RXD2 */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_USART2); +} + +void at91_seriald_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTB, 31, 1); /* DTXD */ + at91_set_a_periph(AT91_PIO_PORTB, 30, 0); /* DRXD */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_SYS); +} + +#if defined(CONFIG_ATMEL_SPI) +void at91_spi0_hw_init(unsigned long cs_mask) +{ + at91_set_a_periph(AT91_PIO_PORTD, 10, 0); /* SPI0_MISO */ + at91_set_a_periph(AT91_PIO_PORTD, 11, 0); /* SPI0_MOSI */ + at91_set_a_periph(AT91_PIO_PORTD, 12, 0); /* SPI0_SPCK */ + + if (cs_mask & (1 << 0)) + at91_set_pio_output(AT91_PIO_PORTD, 13, 1); + if (cs_mask & (1 << 1)) + at91_set_pio_output(AT91_PIO_PORTD, 14, 1); + if (cs_mask & (1 << 2)) + at91_set_pio_output(AT91_PIO_PORTD, 15, 1); + if (cs_mask & (1 << 3)) + at91_set_pio_output(AT91_PIO_PORTD, 16, 1); + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_SPI0); +} +#endif + +#ifdef CONFIG_GENERIC_ATMEL_MCI +void at91_mci_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTD, 0, 0); /* MCI0 CMD */ + at91_set_a_periph(AT91_PIO_PORTD, 1, 0); /* MCI0 DA0 */ + at91_set_a_periph(AT91_PIO_PORTD, 2, 0); /* MCI0 DA1 */ + at91_set_a_periph(AT91_PIO_PORTD, 3, 0); /* MCI0 DA2 */ + at91_set_a_periph(AT91_PIO_PORTD, 4, 0); /* MCI0 DA3 */ +#ifdef CONFIG_ATMEL_MCI_8BIT + at91_set_a_periph(AT91_PIO_PORTD, 5, 0); /* MCI0 DA4 */ + at91_set_a_periph(AT91_PIO_PORTD, 6, 0); /* MCI0 DA5 */ + at91_set_a_periph(AT91_PIO_PORTD, 7, 0); /* MCI0 DA6 */ + at91_set_a_periph(AT91_PIO_PORTD, 8, 0); /* MCI0 DA7 */ +#endif + at91_set_a_periph(AT91_PIO_PORTD, 9, 0); /* MCI0 CLK */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_MCI0); +} +#endif + +#ifdef CONFIG_MACB +void at91_macb_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* ETXCK_EREFCK */ + at91_set_a_periph(AT91_PIO_PORTC, 5, 0); /* ERXDV */ + at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* ERX0 */ + at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* ERX1 */ + at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* ERXER */ + at91_set_a_periph(AT91_PIO_PORTC, 4, 0); /* ETXEN */ + at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* ETX0 */ + at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* ETX1 */ + at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* EMDIO */ + at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* EMDC */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_EMAC); +} +#endif + +#ifdef CONFIG_LCD +void at91_lcd_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTA, 24, 0); /* LCDPWM */ + at91_set_a_periph(AT91_PIO_PORTA, 25, 0); /* LCDDISP */ + at91_set_a_periph(AT91_PIO_PORTA, 26, 0); /* LCDVSYNC */ + at91_set_a_periph(AT91_PIO_PORTA, 27, 0); /* LCDHSYNC */ + at91_set_a_periph(AT91_PIO_PORTA, 28, 0); /* LCDDOTCK */ + at91_set_a_periph(AT91_PIO_PORTA, 29, 0); /* LCDDEN */ + + /* The lower 16-bit of LCD only available on Port A */ + at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* LCDD0 */ + at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* LCDD1 */ + at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* LCDD2 */ + at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* LCDD3 */ + at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* LCDD4 */ + at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* LCDD5 */ + at91_set_a_periph(AT91_PIO_PORTA, 6, 0); /* LCDD6 */ + at91_set_a_periph(AT91_PIO_PORTA, 7, 0); /* LCDD7 */ + at91_set_a_periph(AT91_PIO_PORTA, 8, 0); /* LCDD8 */ + at91_set_a_periph(AT91_PIO_PORTA, 9, 0); /* LCDD9 */ + at91_set_a_periph(AT91_PIO_PORTA, 10, 0); /* LCDD10 */ + at91_set_a_periph(AT91_PIO_PORTA, 11, 0); /* LCDD11 */ + at91_set_a_periph(AT91_PIO_PORTA, 12, 0); /* LCDD12 */ + at91_set_a_periph(AT91_PIO_PORTA, 13, 0); /* LCDD13 */ + at91_set_a_periph(AT91_PIO_PORTA, 14, 0); /* LCDD14 */ + at91_set_a_periph(AT91_PIO_PORTA, 15, 0); /* LCDD15 */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_LCDC); +} +#endif diff --git a/arch/arm/cpu/armv7/at91/timer.c b/arch/arm/cpu/armv7/at91/timer.c new file mode 100644 index 0000000..b3a450f --- /dev/null +++ b/arch/arm/cpu/armv7/at91/timer.c @@ -0,0 +1,139 @@ +/* + * (C) Copyright 2007-2008 + * Stelian Pop stelian@popies.net + * Lead Tech Design <www.leadtechdesign.com> + * + * (C) Copyright 2013 + * Bo Shen voice.shen@atmel.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/at91_pit.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> +#include <div64.h> + +#if !defined(CONFIG_AT91FAMILY) +# error You need to define CONFIG_AT91FAMILY in your board config! +#endif + +DECLARE_GLOBAL_DATA_PTR; + +/* + * We're using the SAMA5D3x PITC in 32 bit mode, by + * setting the 20 bit counter period to its maximum (0xfffff). + * (See the relevant data sheets to understand that this really works) + * + * We do also mimic the typical powerpc way of incrementing + * two 32 bit registers called tbl and tbu. + * + * Those registers increment at 1/16 the main clock rate. + */ + +#define TIMER_LOAD_VAL 0xfffff + +static inline unsigned long long tick_to_time(unsigned long long tick) +{ + tick *= CONFIG_SYS_HZ; + do_div(tick, gd->arch.timer_rate_hz); + + return tick; +} + +static inline unsigned long long usec_to_tick(unsigned long long usec) +{ + usec *= gd->arch.timer_rate_hz; + do_div(usec, 1000000); + + return usec; +} + +/* + * Use the PITC in full 32 bit incrementing mode + */ +int timer_init(void) +{ + at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT; + + /* Enable PITC Clock */ + at91_periph_clk_enable(ATMEL_ID_SYS); + + /* Enable PITC */ + writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr); + + gd->arch.timer_rate_hz = gd->arch.mck_rate_hz / 16; + gd->arch.tbu = 0; + gd->arch.tbl = 0; + + return 0; +} + +/* + * Get the current 64 bit timer tick count + */ +unsigned long long get_ticks(void) +{ + at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT; + + ulong now = readl(&pit->piir); + + /* increment tbu if tbl has rolled over */ + if (now < gd->arch.tbl) + gd->arch.tbu++; + gd->arch.tbl = now; + return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl; +} + +void __udelay(unsigned long usec) +{ + unsigned long long start; + ulong tmo; + + start = get_ticks(); /* get current timestamp */ + tmo = usec_to_tick(usec); /* convert usecs to ticks */ + while ((get_ticks() - start) < tmo) + ; /* loop till time has passed */ +} + +/* + * get_timer(base) can be used to check for timeouts or + * to measure elasped time relative to an event: + * + * ulong start_time = get_timer(0) sets start_time to the current + * time value. + * get_timer(start_time) returns the time elapsed since then. + * + * The time is used in CONFIG_SYS_HZ units! + */ +ulong get_timer(ulong base) +{ + return tick_to_time(get_ticks()) - base; +} + +/* + * Return the number of timer ticks per second. + */ +ulong get_tbclk(void) +{ + return gd->arch.timer_rate_hz; +} diff --git a/arch/arm/include/asm/arch-at91/at91_dbu.h b/arch/arm/include/asm/arch-at91/at91_dbu.h index 3429293..9a640a5 100644 --- a/arch/arm/include/asm/arch-at91/at91_dbu.h +++ b/arch/arm/include/asm/arch-at91/at91_dbu.h @@ -38,4 +38,8 @@ typedef struct at91_dbu { #define AT91_DBU_CID_ARCH_9xx 0x01900000 #define AT91_DBU_CID_ARCH_9XExx 0x02900000

+#define AT91_DBU_CIDR_MASK 0x1f +#define AT91_DBU_CIDR 0x40 +#define AT91_DBU_EXID 0x44 + #endif diff --git a/arch/arm/include/asm/arch-at91/clk.h b/arch/arm/include/asm/arch-at91/clk.h index d4852a3..04b0f83 100644 --- a/arch/arm/include/asm/arch-at91/clk.h +++ b/arch/arm/include/asm/arch-at91/clk.h @@ -95,4 +95,5 @@ static inline unsigned long get_mci_clk_rate(void) }

int at91_clock_init(unsigned long main_clock); +void at91_periph_clk_enable(int id); #endif /* __ASM_ARM_ARCH_CLK_H__ */ diff --git a/arch/arm/include/asm/arch-at91/hardware.h b/arch/arm/include/asm/arch-at91/hardware.h index 8812b11..b04641e 100644 --- a/arch/arm/include/asm/arch-at91/hardware.h +++ b/arch/arm/include/asm/arch-at91/hardware.h @@ -43,6 +43,8 @@ # include <asm/arch/at91cap9.h> #elif defined(CONFIG_AT91X40) # include <asm/arch/at91x40.h> +#elif defined(CONFIG_SAMA5D3) +# include <asm/arch/sama5d3.h> #else # error "Unsupported AT91 processor" #endif diff --git a/arch/arm/include/asm/arch-at91/sama5d3.h b/arch/arm/include/asm/arch-at91/sama5d3.h new file mode 100644 index 0000000..883b932 --- /dev/null +++ b/arch/arm/include/asm/arch-at91/sama5d3.h @@ -0,0 +1,212 @@ +/* + * Chip-specific header file for the SAMA5D3 family + * + * (C) 2012 - 2013 Atmel Corporation. + * Bo Shen voice.shen@atmel.com + * + * Definitions for the SoC: + * SAMA5D3 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef SAMA5D3_H +#define SAMA5D3_H + +/* + * defines to be used in other places + */ +#define CONFIG_ARMV7 /* ARM A5 Core */ +#define CONFIG_AT91FAMILY /* it's a member of AT91 */ + +/* + * Peripheral identifiers/interrupts. + */ +#define ATMEL_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ +#define ATMEL_ID_SYS 1 /* System Controller Interrupt */ +#define ATMEL_ID_DBGU 2 /* Debug Unit Interrupt */ +#define ATMEL_ID_PIT 3 /* Periodic Interval Timer Interrupt */ +#define ATMEL_ID_WDT 4 /* Watchdog timer Interrupt */ +#define ATMEL_ID_SMC 5 /* Multi-bit ECC Interrupt */ +#define ATMEL_ID_PIOA 6 /* Parallel I/O Controller A */ +#define ATMEL_ID_PIOB 7 /* Parallel I/O Controller B */ +#define ATMEL_ID_PIOC 8 /* Parallel I/O Controller C */ +#define ATMEL_ID_PIOD 9 /* Parallel I/O Controller D */ +#define ATMEL_ID_PIOE 10 /* Parallel I/O Controller E */ +#define ATMEL_ID_SMD 11 /* SMD Soft Modem */ +#define ATMEL_ID_USART0 12 /* USART 0 */ +#define ATMEL_ID_USART1 13 /* USART 1 */ +#define ATMEL_ID_USART2 14 /* USART 2 */ +#define ATMEL_ID_USART3 15 /* USART 3 */ +#define ATMEL_ID_UART0 16 +#define ATMEL_ID_UART1 17 +#define ATMEL_ID_TWI0 18 /* Two-Wire Interface 0 */ +#define ATMEL_ID_TWI1 19 /* Two-Wire Interface 1 */ +#define ATMEL_ID_TWI2 20 /* Two-Wire Interface 2 */ +#define ATMEL_ID_MCI0 21 /* High Speed Multimedia Card Interface 0 */ +#define ATMEL_ID_MCI1 22 /* */ +#define ATMEL_ID_MCI2 23 /* */ +#define ATMEL_ID_SPI0 24 /* Serial Peripheral Interface 0 */ +#define ATMEL_ID_SPI1 25 /* Serial Peripheral Interface 1 */ +#define ATMEL_ID_TC0 26 /* */ +#define ATMEL_ID_TC1 27 /* */ +#define ATMEL_ID_PWMC 28 /* Pulse Width Modulation Controller */ +#define ATMEL_ID_TSC 29 /* Touch Screen ADC Controller */ +#define ATMEL_ID_DMA0 30 /* DMA Controller */ +#define ATMEL_ID_DMA1 31 /* DMA Controller */ +#define ATMEL_ID_UHPHS 32 /* USB Host High Speed */ +#define ATMEL_ID_UDPHS 33 /* USB Device High Speed */ +#define ATMEL_ID_GMAC 34 +#define ATMEL_ID_EMAC 35 /* Ethernet MAC */ +#define ATMEL_ID_LCDC 36 /* LCD Controller */ +#define ATMEL_ID_ISI 37 /* Image Sensor Interface */ +#define ATMEL_ID_SSC0 38 /* Synchronous Serial Controller 0 */ +#define ATMEL_ID_SSC1 39 /* Synchronous Serial Controller 1 */ +#define ATMEL_ID_CAN0 40 +#define ATMEL_ID_CAN1 41 +#define ATMEL_ID_SHA 42 +#define ATMEL_ID_AES 43 +#define ATMEL_ID_TDES 44 +#define ATMEL_ID_TRNG 45 +#define ATMEL_ID_ARM 46 +#define ATMEL_ID_IRQ0 47 /* Advanced Interrupt Controller */ +#define ATMEL_ID_FUSE 48 +#define ATMEL_ID_MPDDRC 49 + +/* sama5d3 series chip id definitions */ +#define ARCH_ID_SAMA5D3 0x8a5c07c0 +#define ARCH_EXID_SAMA5D31 0x00444300 +#define ARCH_EXID_SAMA5D33 0x00414300 +#define ARCH_EXID_SAMA5D34 0x00414301 +#define ARCH_EXID_SAMA5D35 0x00584300 + +#define cpu_is_sama5d3() (get_chip_id() == ARCH_ID_SAMA5D3) +#define cpu_is_sama5d31() (cpu_is_sama5d3() && \ + (get_extension_chip_id() == ARCH_EXID_SAMA5D31)) +#define cpu_is_sama5d33() (cpu_is_sama5d3() && \ + (get_extension_chip_id() == ARCH_EXID_SAMA5D33)) +#define cpu_is_sama5d34() (cpu_is_sama5d3() && \ + (get_extension_chip_id() == ARCH_EXID_SAMA5D34)) +#define cpu_is_sama5d35() (cpu_is_sama5d3() && \ + (get_extension_chip_id() == ARCH_EXID_SAMA5D35)) + +/* + * User Peripherals physical base addresses. + */ +#define ATMEL_BASE_MCI0 0xf0000000 +#define ATMEL_BASE_SPI0 0xf0004000 +#define ATMEL_BASE_SSC0 0xf000C000 +#define ATMEL_BASE_TC2 0xf0010000 +#define ATMEL_BASE_TWI0 0xf0014000 +#define ATMEL_BASE_TWI1 0xf0018000 +#define ATMEL_BASE_USART0 0xf001c000 +#define ATMEL_BASE_USART1 0xf0020000 +#define ATMEL_BASE_UART0 0xf0024000 +#define ATMEL_BASE_GMAC 0xf0028000 +#define ATMEL_BASE_PWMC 0xf002c000 +#define ATMEL_BASE_LCDC 0xf0030000 +#define ATMEL_BASE_ISI 0xf0034000 +#define ATMEL_BASE_SFR 0xf0038000 +/* Reserved: 0xf003c000 - 0xf8000000 */ +#define ATMEL_BASE_MCI1 0xf8000000 +#define ATMEL_BASE_MCI2 0xf8004000 +#define ATMEL_BASE_SPI1 0xf8008000 +#define ATMEL_BASE_SSC1 0xf800c000 +#define ATMEL_BASE_CAN1 0xf8010000 +#define ATMEL_BASE_TC3 0xf8014000 +#define ATMEL_BASE_TSADC 0xf8018000 +#define ATMEL_BASE_TWI2 0xf801c000 +#define ATMEL_BASE_USART2 0xf8020000 +#define ATMEL_BASE_USART3 0xf8024000 +#define ATMEL_BASE_UART1 0xf8028000 +#define ATMEL_BASE_EMAC 0xf802c000 +#define ATMEL_BASE_UDHPS 0xf8030000 +#define ATMEL_BASE_SHA 0xf8034000 +#define ATMEL_BASE_AES 0xf8038000 +#define ATMEL_BASE_TDES 0xf803c000 +#define ATMEL_BASE_TRNG 0xf8040000 +/* Reserved: 0xf804400 - 0xffffc00 */ + +/* + * System Peripherals physical base addresses. + */ +#define ATMEL_BASE_SYS 0xffffc000 +#define ATMEL_BASE_SMC 0xffffc000 +#define ATMEL_BASE_PMECC (ATMEL_BASE_SMC + 0x070) +#define ATMEL_BASE_PMERRLOC (ATMEL_BASE_SMC + 0x500) +#define ATMEL_BASE_FUSE 0xffffe400 +#define ATMEL_BASE_DMAC0 0xffffe600 +#define ATMEL_BASE_DMAC1 0xffffe800 +#define ATMEL_BASE_MPDDRC 0xffffea00 +#define ATMEL_BASE_MATRIX 0xffffec00 +#define ATMEL_BASE_DBGU 0xffffee00 +#define ATMEL_BASE_AIC 0xfffff000 +#define ATMEL_BASE_PIOA 0xfffff200 +#define ATMEL_BASE_PIOB 0xfffff400 +#define ATMEL_BASE_PIOC 0xfffff600 +#define ATMEL_BASE_PIOD 0xfffff800 +#define ATMEL_BASE_PIOE 0xfffffa00 +#define ATMEL_BASE_PMC 0xfffffc00 +#define ATMEL_BASE_RSTC 0xfffffe00 +#define ATMEL_BASE_SHDWN 0xfffffe10 +#define ATMEL_BASE_PIT 0xfffffe30 +#define ATMEL_BASE_WDT 0xfffffe40 +#define ATMEL_BASE_SCKCR 0xfffffe50 +#define ATMEL_BASE_GPBR 0xfffffe60 +#define ATMEL_BASE_RTC 0xfffffeb0 +/* Reserved: 0xfffffee0 - 0xffffffff */ + +/* + * Internal Memory. + */ +#define ATMEL_BASE_ROM 0x00100000 /* Internal ROM base address */ +#define ATMEL_BASE_SRAM 0x00200000 /* Internal ROM base address */ +#define ATMEL_BASE_SRAM0 0x00300000 /* Internal SRAM base address */ +#define ATMEL_BASE_SRAM1 0x00310000 /* Internal SRAM base address */ +#define ATMEL_BASE_SMD 0x00400000 /* Internal ROM base address */ +#define ATMEL_BASE_UDPHS_FIFO 0x00500000 /* USB Device HS controller */ +#define ATMEL_BASE_OHCI 0x00600000 /* USB Host controller (OHCI) */ +#define ATMEL_BASE_EHCI 0x00700000 /* USB Host controller (EHCI) */ +#define ATMEL_BASE_AXI 0x00800000 /* Video Decoder Controller */ +#define ATMEL_BASE_DAP 0x00900000 /* Video Decoder Controller */ + +/* + * External memory + */ +#define ATMEL_BASE_CS0 0x10000000 +#define ATMEL_BASE_DDRCS 0x20000000 +#define ATMEL_BASE_CS1 0x40000000 +#define ATMEL_BASE_CS2 0x50000000 +#define ATMEL_BASE_CS3 0x60000000 + +/* + * Other misc defines + */ +#define ATMEL_PIO_PORTS 5 +#define CPU_HAS_PIO3 +#define PIO_SCDR_DIV 0x3fff + +/* + * PMECC table in ROM + */ +#define ATMEL_PMECC_INDEX_OFFSET_512 0x10000 +#define ATMEL_PMECC_INDEX_OFFSET_1024 0x18000 +#define ATMEL_PMECC_ALPHA_OFFSET_512 0x10000 +#define ATMEL_PMECC_ALPHA_OFFSET_1024 0x18000 + +/* + * SAMA5D3 specific prototypes + */ +#ifndef __ASSEMBLY__ +unsigned int get_chip_id(void); +unsigned int get_extension_chip_id(void); +unsigned int has_emac(void); +unsigned int has_gmac(void); +unsigned int has_lcdc(void); +char *get_cpu_name(void); +#endif + +#endif diff --git a/arch/arm/include/asm/arch-at91/sama5d3_smc.h b/arch/arm/include/asm/arch-at91/sama5d3_smc.h new file mode 100644 index 0000000..eb53eba --- /dev/null +++ b/arch/arm/include/asm/arch-at91/sama5d3_smc.h @@ -0,0 +1,79 @@ +/* + * Copyright (C) 2012 Atmel Corporation. + * + * Static Memory Controllers (SMC) - System peripherals registers. + * Based on SAMA5D3 datasheet. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef SAMA5D3_SMC_H +#define SAMA5D3_SMC_H + +#ifdef __ASSEMBLY__ +#define AT91_ASM_SMC_SETUP0 (ATMEL_BASE_SMC + 0x600) +#define AT91_ASM_SMC_PULSE0 (ATMEL_BASE_SMC + 0x604) +#define AT91_ASM_SMC_CYCLE0 (ATMEL_BASE_SMC + 0x608) +#define AT91_ASM_SMC_MODE0 (ATMEL_BASE_SMC + 0x60C) +#else +struct at91_cs { + u32 reserved[96]; + u32 setup; /* 0x600 SMC Setup Register */ + u32 pulse; /* 0x604 SMC Pulse Register */ + u32 cycle; /* 0x608 SMC Cycle Register */ + u32 timings; /* 0x60C SMC Cycle Register */ + u32 mode; /* 0x610 SMC Mode Register */ +}; + +struct at91_smc { + struct at91_cs cs[4]; +}; +#endif /* __ASSEMBLY__ */ + +#define AT91_SMC_SETUP_NWE(x) (x & 0x3f) +#define AT91_SMC_SETUP_NCS_WR(x) ((x & 0x3f) << 8) +#define AT91_SMC_SETUP_NRD(x) ((x & 0x3f) << 16) +#define AT91_SMC_SETUP_NCS_RD(x) ((x & 0x3f) << 24) + +#define AT91_SMC_PULSE_NWE(x) (x & 0x3f) +#define AT91_SMC_PULSE_NCS_WR(x) ((x & 0x3f) << 8) +#define AT91_SMC_PULSE_NRD(x) ((x & 0x3f) << 16) +#define AT91_SMC_PULSE_NCS_RD(x) ((x & 0x3f) << 24) + +#define AT91_SMC_CYCLE_NWE(x) (x & 0x1ff) +#define AT91_SMC_CYCLE_NRD(x) ((x & 0x1ff) << 16) + +#define AT91_SMC_TIMINGS_TCLR(x) (x & 0xf) +#define AT91_SMC_TIMINGS_TADL(x) ((x & 0xf) << 4) +#define AT91_SMC_TIMINGS_TAR(x) ((x & 0xf) << 8) +#define AT91_SMC_TIMINGS_OCMS(x) ((x & 0x1) << 12) +#define AT91_SMC_TIMINGS_TRR(x) ((x & 0xf) << 16) +#define AT91_SMC_TIMINGS_TWB(x) ((x & 0xf) << 24) +#define AT91_SMC_TIMINGS_RBNSEL(x) ((x & 0xf) << 28) +#define AT91_SMC_TIMINGS_NFSEL(x) ((x & 0x1) << 31) + +#define AT91_SMC_MODE_RM_NCS 0x00000000 +#define AT91_SMC_MODE_RM_NRD 0x00000001 +#define AT91_SMC_MODE_WM_NCS 0x00000000 +#define AT91_SMC_MODE_WM_NWE 0x00000002 + +#define AT91_SMC_MODE_EXNW_DISABLE 0x00000000 +#define AT91_SMC_MODE_EXNW_FROZEN 0x00000020 +#define AT91_SMC_MODE_EXNW_READY 0x00000030 + +#define AT91_SMC_MODE_BAT 0x00000100 +#define AT91_SMC_MODE_DBW_8 0x00000000 +#define AT91_SMC_MODE_DBW_16 0x00001000 +#define AT91_SMC_MODE_DBW_32 0x00002000 +#define AT91_SMC_MODE_TDF_CYCLE(x) ((x & 0xf) << 16) +#define AT91_SMC_MODE_TDF 0x00100000 +#define AT91_SMC_MODE_PMEN 0x01000000 +#define AT91_SMC_MODE_PS_4 0x00000000 +#define AT91_SMC_MODE_PS_8 0x10000000 +#define AT91_SMC_MODE_PS_16 0x20000000 +#define AT91_SMC_MODE_PS_32 0x30000000 + +#endif diff --git a/board/atmel/sama5d3xek/Makefile b/board/atmel/sama5d3xek/Makefile new file mode 100644 index 0000000..45d24d2 --- /dev/null +++ b/board/atmel/sama5d3xek/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2008 +# Stelian Pop stelian@popies.net +# Lead Tech Design <www.leadtechdesign.com> +# +# (C) Copyright 2013 +# Bo Shen voice.shen@atmel.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += sama5d3xek.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/atmel/sama5d3xek/sama5d3xek.c b/board/atmel/sama5d3xek/sama5d3xek.c new file mode 100644 index 0000000..541296d --- /dev/null +++ b/board/atmel/sama5d3xek/sama5d3xek.c @@ -0,0 +1,275 @@ +/* + * Copyright (C) 2012 - 2013 Atmel Corporation + * Bo Shen voice.shen@atmel.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <mmc.h> +#include <asm/io.h> +#include <asm/arch/sama5d3_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/clk.h> +#include <lcd.h> +#include <atmel_lcdc.h> +#include <atmel_mci.h> +#include <net.h> +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* ------------------------------------------------------------------------- */ +/* + * Miscelaneous platform dependent initialisations + */ + +#ifdef CONFIG_NAND_ATMEL +void sama5d3xek_nand_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + + at91_periph_clk_enable(ATMEL_ID_SMC); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(1) | + AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(1), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(5), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8), + &smc->cs[3].cycle); + writel(AT91_SMC_TIMINGS_TCLR(3) | AT91_SMC_TIMINGS_TADL(10) | + AT91_SMC_TIMINGS_TAR(3) | AT91_SMC_TIMINGS_TRR(4) | + AT91_SMC_TIMINGS_TWB(5) | AT91_SMC_TIMINGS_RBNSEL(3)| + AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | +#ifdef CONFIG_SYS_NAND_DBW_16 + AT91_SMC_MODE_DBW_16 | +#else /* CONFIG_SYS_NAND_DBW_8 */ + AT91_SMC_MODE_DBW_8 | +#endif + AT91_SMC_MODE_TDF_CYCLE(3), + &smc->cs[3].mode); +} +#endif + +#ifdef CONFIG_CMD_USB +static void sama5d3xek_usb_hw_init(void) +{ + at91_set_pio_output(AT91_PIO_PORTD, 25, 0); + at91_set_pio_output(AT91_PIO_PORTD, 26, 0); + at91_set_pio_output(AT91_PIO_PORTD, 27, 0); +} +#endif + +#ifdef CONFIG_GENERIC_ATMEL_MCI +static void sama5d3xek_mci_hw_init(void) +{ + at91_mci_hw_init(); + + at91_set_pio_output(AT91_PIO_PORTB, 10, 0); /* MCI0 Power */ +} +#endif + +#ifdef CONFIG_LCD +vidinfo_t panel_info = { + .vl_col = 800, + .vl_row = 480, + .vl_clk = 24000000, + .vl_sync = ATMEL_LCDC_INVLINE_NORMAL | ATMEL_LCDC_INVFRAME_NORMAL, + .vl_bpix = LCD_BPP, + .vl_tft = 1, + .vl_hsync_len = 128, + .vl_left_margin = 64, + .vl_right_margin = 64, + .vl_vsync_len = 2, + .vl_upper_margin = 22, + .vl_lower_margin = 21, + .mmio = ATMEL_BASE_LCDC, +}; + +void lcd_enable(void) +{ +} + +void lcd_disable(void) +{ +} + +static void sama5d3xek_lcd_hw_init(void) +{ + gd->fb_base = CONFIG_SAMA5D3_LCD_BASE; + + /* The higher 8 bit of LCD is board related */ + at91_set_c_periph(AT91_PIO_PORTC, 14, 0); /* LCDD16 */ + at91_set_c_periph(AT91_PIO_PORTC, 13, 0); /* LCDD17 */ + at91_set_c_periph(AT91_PIO_PORTC, 12, 0); /* LCDD18 */ + at91_set_c_periph(AT91_PIO_PORTC, 11, 0); /* LCDD19 */ + at91_set_c_periph(AT91_PIO_PORTC, 10, 0); /* LCDD20 */ + at91_set_c_periph(AT91_PIO_PORTC, 15, 0); /* LCDD21 */ + at91_set_c_periph(AT91_PIO_PORTE, 27, 0); /* LCDD22 */ + at91_set_c_periph(AT91_PIO_PORTE, 28, 0); /* LCDD23 */ + + /* Configure lower 16 bit of LCD and enable clock */ + at91_lcd_hw_init(); +} + +#ifdef CONFIG_LCD_INFO +#include <nand.h> +#include <version.h> + +void lcd_show_board_info(void) +{ + ulong dram_size, nand_size; + int i; + char temp[32]; + + lcd_printf("%s\n", U_BOOT_VERSION); + lcd_printf("(C) 2013 ATMEL Corp\n"); + lcd_printf("at91@atmel.com\n"); + lcd_printf("%s CPU at %s MHz\n", get_cpu_name(), + strmhz(temp, get_cpu_clk_rate())); + + dram_size = 0; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) + dram_size += gd->bd->bi_dram[i].size; + + nand_size = 0; +#ifdef CONFIG_NAND_ATMEL + for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) + nand_size += nand_info[i].size; +#endif + lcd_printf("%ld MB SDRAM, %ld MB NAND\n", + dram_size >> 20, nand_size >> 20); +} +#endif /* CONFIG_LCD_INFO */ +#endif /* CONFIG_LCD */ + +int board_early_init_f(void) +{ + at91_seriald_hw_init(); + + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + +#ifdef CONFIG_NAND_ATMEL + sama5d3xek_nand_hw_init(); +#endif +#ifdef CONFIG_CMD_USB + sama5d3xek_usb_hw_init(); +#endif +#ifdef CONFIG_GENERIC_ATMEL_MCI + sama5d3xek_mci_hw_init(); +#endif +#ifdef CONFIG_ATMEL_SPI + at91_spi0_hw_init(1 << 0); +#endif +#ifdef CONFIG_MACB + if (has_emac()) + at91_macb_hw_init(); +#endif +#ifdef CONFIG_LCD + if (has_lcdc()) + sama5d3xek_lcd_hw_init(); +#endif + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; +} + +int board_eth_init(bd_t *bis) +{ + int rc = 0; + +#ifdef CONFIG_MACB + if (has_emac()) + rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00); +#endif + + return rc; +} + +#ifdef CONFIG_GENERIC_ATMEL_MCI +int board_mmc_init(bd_t *bis) +{ + int rc = 0; + + rc = atmel_mci_init((void *)ATMEL_BASE_MCI0); + + return rc; +} +#endif + +/* SPI chip select control */ +#ifdef CONFIG_ATMEL_SPI +#include <spi.h> + +int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{ + return bus == 0 && cs < 4; +} + +void spi_cs_activate(struct spi_slave *slave) +{ + switch (slave->cs) { + case 0: + at91_set_pio_output(AT91_PIO_PORTD, 13, 0); + case 1: + at91_set_pio_output(AT91_PIO_PORTD, 14, 0); + case 2: + at91_set_pio_output(AT91_PIO_PORTD, 15, 0); + case 3: + at91_set_pio_output(AT91_PIO_PORTD, 16, 0); + default: + break; + } +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + switch (slave->cs) { + case 0: + at91_set_pio_output(AT91_PIO_PORTD, 13, 1); + case 1: + at91_set_pio_output(AT91_PIO_PORTD, 14, 1); + case 2: + at91_set_pio_output(AT91_PIO_PORTD, 15, 1); + case 3: + at91_set_pio_output(AT91_PIO_PORTD, 16, 1); + default: + break; + } +} +#endif /* CONFIG_ATMEL_SPI */ diff --git a/boards.cfg b/boards.cfg index ef1817f..c99bab8 100644 --- a/boards.cfg +++ b/boards.cfg @@ -249,6 +249,9 @@ am335x_evm_uart5 arm armv7 am335x ti am335x_evm_usbspl arm armv7 am335x ti am33xx am335x_evm:SERIAL1,CONS_INDEX=1,SPL_USBETH_SUPPORT ti814x_evm arm armv7 ti814x ti am33xx pcm051 arm armv7 pcm051 phytec am33xx pcm051 +sama5d3xek_mmc arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_MMC +sama5d3xek_nandflash arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_NANDFLASH +sama5d3xek_spiflash arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_SERIALFLASH highbank arm armv7 highbank - highbank m53evk arm armv7 m53evk denx mx5 m53evk:IMX_CONFIG=board/denx/m53evk/imximage.cfg mx51_efikamx arm armv7 mx51_efikamx genesi mx5 mx51_efikamx:MACH_TYPE=MACH_TYPE_MX51_EFIKAMX,IMX_CONFIG=board/genesi/mx51_efikamx/imximage_mx.cfg diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h new file mode 100644 index 0000000..c13e983 --- /dev/null +++ b/include/configs/sama5d3xek.h @@ -0,0 +1,245 @@ +/* + * Configuation settings for the SAMA5D3xEK board. + * + * Copyright (C) 2012 - 2013 Atmel + * + * based on at91sam9m10g45ek.h by: + * Stelian Pop stelian@popies.net + * Lead Tech Design <www.leadtechdesign.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/hardware.h> + +#define CONFIG_SYS_TEXT_BASE 0x26f00000 + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_AT91FAMILY +#define CONFIG_ARCH_CPU_INIT + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT /* Device Tree support */ + +/* general purpose I/O */ +#define CONFIG_AT91_GPIO + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_DBGU + +/* + * This needs to be defined for the OHCI code to work but it is defined as + * ATMEL_ID_UHPHS in the CPU specific header files. + */ +#define ATMEL_ID_UHP ATMEL_ID_UHPHS + +/* + * Specify the clock enable bit in the PMC_SCER register. + */ +#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP + +/* LCD */ +#define CONFIG_LCD +#define LCD_BPP LCD_COLOR16 +#define LCD_OUTPUT_BPP 24 +#define CONFIG_LCD_LOGO +#undef LCD_TEST_PATTERN +#define CONFIG_LCD_INFO +#define CONFIG_LCD_INFO_BELOW_LOGO +#define CONFIG_SYS_WHITE_ON_BLACK +#define CONFIG_ATMEL_HLCD +#define CONFIG_ATMEL_LCD_RGB565 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +/* board specific (not enough SRAM) */ +#define CONFIG_SAMA5D3_LCD_BASE 0x23E00000 + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* No NOR flash */ +#define CONFIG_SYS_NO_FLASH + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_LOADS +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS +#define CONFIG_SYS_SDRAM_SIZE 0x20000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) + +/* SerialFlash */ +#define CONFIG_CMD_SF + +#ifdef CONFIG_CMD_SF +#define CONFIG_ATMEL_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#endif + +/* NAND flash */ +#define CONFIG_CMD_NAND + +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_MAX_CHIPS 1 +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ONFI_DETECTION +/* PMECC & PMERRLOC */ +#define CONFIG_ATMEL_NAND_HWECC +#define CONFIG_ATMEL_NAND_HW_PMECC +#define CONFIG_PMECC_CAP 4 +#define CONFIG_PMECC_SECTOR_SIZE 512 +#define CONFIG_PMECC_INDEX_TABLE_OFFSET ATMEL_PMECC_INDEX_OFFSET_512 +#define CONFIG_CMD_NAND_TRIMFFS +#endif + +/* Ethernet Hardware */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_MULTI +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_MACB_SEARCH_PHY + +/* MMC */ +#define CONFIG_CMD_MMC + +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#define ATMEL_BASE_MMCI ATMEL_BASE_MCI0 +#endif + +/* USB */ +#define CONFIG_CMD_USB + +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "sama5d3" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3 +#define CONFIG_DOS_PARTITION +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) +#define CONFIG_CMD_FAT +#endif + +#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ + +#ifdef CONFIG_SYS_USE_SERIALFLASH +/* bootstrap + u-boot + env + linux in serial flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x5000 +#define CONFIG_ENV_SIZE 0x3000 +#define CONFIG_ENV_SECT_SIZE 0x1000 +#define CONFIG_BOOTCOMMAND "sf probe 0; " \ + "sf read 0x22000000 0x42000 0x300000; " \ + "bootm 0x22000000" +#elif CONFIG_SYS_USE_NANDFLASH +/* bootstrap + u-boot + env in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0xc0000 +#define CONFIG_ENV_OFFSET_REDUND 0x100000 +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \ + "nand read 0x22000000 0x200000 0x600000;" \ + "bootm 0x22000000 - 0x21000000" +#elif CONFIG_SYS_USE_MMC +/* bootstrap + u-boot + env in sd card */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 dtb; " \ + "fatload mmc 0:1 0x22000000 uImage; " \ + "bootm 0x22000000 - 0x21000000" +#define CONFIG_SYS_MMC_ENV_DEV 0 +#else +#define CONIG_ENV_IS_NOWHERE +#endif + +#ifdef CONFIG_SYS_USE_MMC +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "root=/dev/mmcblk0p2 rw rootwait" +#else +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ + "256K(env),256k(evn_redundent),256k(spare)," \ + "512k(dtb),6M(kernel)ro,-(rootfs) " \ + "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs" +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) + +#endif