From: Simon Guinot simon.guinot@sequanux.org

Consider that ide_preinit() succeed if at least one port is successfully initialized. This allows to iniatialize IDE support on a board with two SATA ports but a single hard disk available.

Signed-off-by: Simon Guinot simon.guinot@sequanux.org --- drivers/block/mvsata_ide.c | 14 ++++++++------ 1 files changed, 8 insertions(+), 6 deletions(-)

diff --git a/drivers/block/mvsata_ide.c b/drivers/block/mvsata_ide.c index 1be395f..c7357fc 100644 --- a/drivers/block/mvsata_ide.c +++ b/drivers/block/mvsata_ide.c @@ -150,23 +150,25 @@ static int mvsata_ide_initialize_port(struct mvsata_port_registers *port)

int ide_preinit(void) { + int ret = 1; int status; + /* Enable ATA port 0 (could be SATA port 0 or 1) if declared */ #if defined(CONFIG_SYS_ATA_IDE0_OFFSET) status = mvsata_ide_initialize_port( (struct mvsata_port_registers *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET)); - if (status) - return status; + if (status == MVSATA_STATUS_OK) + ret = 0; #endif /* Enable ATA port 1 (could be SATA port 0 or 1) if declared */ #if defined(CONFIG_SYS_ATA_IDE1_OFFSET) status = mvsata_ide_initialize_port( (struct mvsata_port_registers *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE1_OFFSET)); - if (status) - return status; + if (status == MVSATA_STATUS_OK) + ret = 0; #endif - /* return success if all ports initializations succeeded */ - return MVSATA_STATUS_OK; + /* Return success if at least one port initialization succeeded */ + return ret; }

From: Simon Guinot simon.guinot@sequanux.org

This patch adds support for the LaCie 2Big Network v2 board, based on the Marvell Kirkwood 6281 SoC.

Additional information is available at: http://lacie-nas.org/doku.php?id=2big_network_v2

Signed-off-by: Simon Guinot simon.guinot@sequanux.org --- MAINTAINERS | 1 + board/LaCie/net2big_v2/Makefile | 49 +++++++++ board/LaCie/net2big_v2/kwbimage.cfg | 162 ++++++++++++++++++++++++++++++ board/LaCie/net2big_v2/net2big_v2.c | 188 +++++++++++++++++++++++++++++++++++ board/LaCie/net2big_v2/net2big_v2.h | 43 ++++++++ boards.cfg | 1 + include/configs/net2big_v2.h | 161 ++++++++++++++++++++++++++++++ 7 files changed, 605 insertions(+), 0 deletions(-) create mode 100644 board/LaCie/net2big_v2/Makefile create mode 100644 board/LaCie/net2big_v2/kwbimage.cfg create mode 100644 board/LaCie/net2big_v2/net2big_v2.c create mode 100644 board/LaCie/net2big_v2/net2big_v2.h create mode 100644 include/configs/net2big_v2.h

diff --git a/MAINTAINERS b/MAINTAINERS index 21d1fef..8c2b3a6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -649,6 +649,7 @@ Simon Guinot simon.guinot@sequanux.org inetspace_v2 ARM926EJS (Kirkwood SoC) netspace_v2 ARM926EJS (Kirkwood SoC) netspace_max_v2 ARM926EJS (Kirkwood SoC) + net2big_v2 ARM926EJS (Kirkwood SoC)

Igor Grinberg grinberg@compulab.co.il

diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile new file mode 100644 index 0000000..4bacef4 --- /dev/null +++ b/board/LaCie/net2big_v2/Makefile @@ -0,0 +1,49 @@ +# +# Copyright (C) 2011 Simon Guinot sguinot@lacie.com +# +# Based on Kirkwood support: +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar prafulla@marvell.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := net2big_v2.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/LaCie/net2big_v2/kwbimage.cfg b/board/LaCie/net2big_v2/kwbimage.cfg new file mode 100644 index 0000000..8d9f153 --- /dev/null +++ b/board/LaCie/net2big_v2/kwbimage.cfg @@ -0,0 +1,162 @@ +# +# Copyright (C) 2011 Simon Guinot sguinot@lacie.com +# +# Based on Kirkwood support: +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar prafulla@marvell.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1B1B1B9B + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000C30 # DDR Configuration register +# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x38743000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000A32 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x0000CCCC # DDR Address Control +# bit1-0: 01, Cs0width=x16 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs2width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000662 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000044 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 1, DDR drive strenght reduced +# bit2: 1, DDR ODT control lsd enabled +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, enabled +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 1 , D2P Latency enabled +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) +# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E40F # CPU ODT Control +# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 +# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0 +# bit11-10:1, DQ_ODTSel. ODT select turned on + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c new file mode 100644 index 0000000..16d1405 --- /dev/null +++ b/board/LaCie/net2big_v2/net2big_v2.c @@ -0,0 +1,188 @@ +/* + * Copyright (C) 2011 Simon Guinot sguinot@lacie.com + * + * Based on Kirkwood support: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <common.h> +#include <miiphy.h> +#include <netdev.h> +#include <command.h> +#include <i2c.h> +#include <asm/arch/cpu.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/mpp.h> +#include <asm/arch/gpio.h> +#include "net2big_v2.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* GPIO configuration */ + kw_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH, + NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + u32 kwmpp_config[] = { + MPP0_SPI_SCn, + MPP1_SPI_MOSI, + MPP2_SPI_SCK, + MPP3_SPI_MISO, + MPP6_SYSRST_OUTn, + MPP7_GPO, /* Request power-off */ + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP13_GPIO, /* Rear power switch (on|auto) */ + MPP14_GPIO, /* USB fuse alarm */ + MPP15_GPIO, /* Rear power switch (auto|off) */ + MPP16_GPIO, /* SATA HDD1 power */ + MPP17_GPIO, /* SATA HDD2 power */ + MPP20_SATA1_ACTn, + MPP21_SATA0_ACTn, + MPP24_GPIO, /* USB mode select */ + MPP26_GPIO, /* USB device vbus */ + MPP28_GPIO, /* USB enable host vbus */ + MPP29_GPIO, /* GPIO extension ALE */ + MPP34_GPIO, /* Rear Push button 0=on 1=off */ + MPP35_GPIO, /* Inhibit switch power-off */ + MPP36_GPIO, /* SATA HDD1 presence */ + MPP37_GPIO, /* SATA HDD2 presence */ + MPP40_GPIO, /* eSATA presence */ + MPP44_GPIO, /* GPIO extension (data 0) */ + MPP45_GPIO, /* GPIO extension (data 1) */ + MPP46_GPIO, /* GPIO extension (data 2) */ + MPP47_GPIO, /* GPIO extension (addr 0) */ + MPP48_GPIO, /* GPIO extension (addr 1) */ + MPP49_GPIO, /* GPIO extension (addr 2) */ + 0 + }; + + kirkwood_mpp_conf(kwmpp_config); + + return 0; +} + +int board_init(void) +{ + /* Machine number */ + gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2; + + /* Boot parameters address */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + + return 0; +} + +int misc_init_r(void) +{ +#ifdef CONFIG_CMD_I2C + if (!getenv("ethaddr")) { + ushort version; + uchar mac[6]; + int ret; + + /* I2C-0 for on-board EEPROM */ + i2c_set_bus_num(0); + + /* Check layout version for EEPROM data */ + ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, + (uchar *) &version, 2); + if (ret != 0) { + printf("Error: failed to read I2C EEPROM @%02x\n", + CONFIG_SYS_I2C_EEPROM_ADDR); + return ret; + } + version = be16_to_cpu(version); + if (version < 1 || version > 3) { + printf("Error: unknown version %d for EEPROM data\n", + version); + return -1; + } + + /* Read Ethernet MAC address from EEPROM */ + ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac, 6); + if (ret != 0) { + printf("Error: failed to read I2C EEPROM @%02x\n", + CONFIG_SYS_I2C_EEPROM_ADDR); + return ret; + } + eth_setenv_enetaddr("ethaddr", mac); + } +#endif /* CONFIG_CMD_I2C */ + + return 0; +} + +void mv_phy_88e1116_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { + printf("Err..(%s) could not read PHY dev address\n", __func__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg); + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); + + /* reset the phy */ + if (miiphy_read(name, devadr, MII_BMCR, &reg) != 0) { + printf("Err..(%s) PHY status read failed\n", __func__); + return; + } + if (miiphy_write(name, devadr, MII_BMCR, reg | 0x8000) != 0) { + printf("Err..(%s) PHY reset failed\n", __func__); + return; + } + + debug("88E1116 Initialized on %s\n", name); +} + +/* Configure and initialize PHY */ +void reset_phy(void) +{ + mv_phy_88e1116_init("egiga0"); +} + +/* Return GPIO push button status */ +static int +do_read_push_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON); +} + +U_BOOT_CMD(button, 1, 1, do_read_push_button, + "Return GPIO push button status 0=off 1=on", ""); diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h new file mode 100644 index 0000000..bbe67af --- /dev/null +++ b/board/LaCie/net2big_v2/net2big_v2.h @@ -0,0 +1,43 @@ +/* + * Copyright (C) 2011 Simon Guinot sguinot@lacie.com + * + * Based on Kirkwood support: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef NET2BIG_V2_H +#define NET2BIG_V2_H + +/* GPIO configuration */ +#define NET2BIG_V2_OE_LOW 0x0600E000 +#define NET2BIG_V2_OE_HIGH 0x00000134 +#define NET2BIG_V2_OE_VAL_LOW 0x10030000 +#define NET2BIG_V2_OE_VAL_HIGH 0x00000000 + +/* Buttons */ +#define NET2BIG_V2_GPIO_PUSH_BUTTON 34 + +/* PHY related */ +#define MV88E1116_LED_FCTRL_REG 10 +#define MV88E1116_CPRSP_CR3_REG 21 +#define MV88E1116_MAC_CTRL_REG 21 +#define MV88E1116_PGADR_REG 22 +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) + +#endif /* NET2BIG_V2_H */ diff --git a/boards.cfg b/boards.cfg index 17effc8..6bb567b 100644 --- a/boards.cfg +++ b/boards.cfg @@ -138,6 +138,7 @@ km_kirkwood_pci arm arm926ejs km_arm keymile mgcoge3un arm arm926ejs km_arm keymile kirkwood portl2 arm arm926ejs km_arm keymile kirkwood inetspace_v2 arm arm926ejs netspace_v2 LaCie kirkwood netspace_v2:INETSPACE_V2 +net2big_v2 arm arm926ejs net2big_v2 LaCie kirkwood netspace_v2 arm arm926ejs netspace_v2 LaCie kirkwood netspace_v2:NETSPACE_V2 netspace_max_v2 arm arm926ejs netspace_v2 LaCie kirkwood netspace_v2:NETSPACE_MAX_V2 dreamplug arm arm926ejs - Marvell kirkwood diff --git a/include/configs/net2big_v2.h b/include/configs/net2big_v2.h new file mode 100644 index 0000000..9cf76d0 --- /dev/null +++ b/include/configs/net2big_v2.h @@ -0,0 +1,161 @@ +/* + * Copyright (C) 2011 Simon Guinot sguinot@lacie.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _CONFIG_NET2BIG_V2_H +#define _CONFIG_NET2BIG_V2_H + +/* + * Machine number information + */ +#define CONFIG_IDENT_STRING " 2Big v2" + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */ +#define CONFIG_KIRKWOOD /* SOC Family Name */ +#define CONFIG_KW88F6281 /* SOC Name */ +#define CONFIG_MACH_NET2BIG_V2 /* Machine type */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_SF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_USB + +/* + * Core clock definition. + */ +#define CONFIG_SYS_TCLK 166000000 /* 166MHz */ + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#define CONFIG_NR_DRAM_BANKS 2 +#include "mv-common.h" + +/* Remove or override few declarations from mv-common.h */ +#undef CONFIG_RBTREE +#undef CONFIG_ENV_SPI_MAX_HZ +#undef CONFIG_SYS_IDE_MAXBUS +#undef CONFIG_SYS_IDE_MAXDEVICE +#undef CONFIG_SYS_PROMPT +#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 1 +#define CONFIG_SYS_PROMPT "2big2> " + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_MISC_INIT_R /* Call misc_init_r() to initialize MAC address */ +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ +#define CONFIG_NETCONSOLE +#endif + +/* + * SATA Driver configuration + */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif + +/* + * Enable GPI0 support + */ +#define CONFIG_KIRKWOOD_GPIO + +/* + * Enable I2C support + */ +#ifdef CONFIG_CMD_I2C +/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */ +#define CONFIG_CMD_EEPROM +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */ +#endif /* CONFIG_CMD_I2C */ + +/* + * File systems support + */ +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT + +/* + * Use the HUSH parser + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * Console configuration + */ +#define CONFIG_CONSOLE_MUX +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +/* + * Enable device tree support + */ +#define CONFIG_OF_LIBFDT + +/* + * Environment variables configurations + */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64KB */ +#define CONFIG_ENV_SIZE 0x1000 /* 4KB */ +#define CONFIG_ENV_ADDR 0x70000 +#define CONFIG_ENV_OFFSET 0x70000 /* env starts here */ + +/* + * Default environment variables + */ +#define CONFIG_BOOTARGS "console=ttyS0,115200" + +#define CONFIG_BOOTCOMMAND \ + "dhcp && run netconsole; " \ + "if run usbload || run diskload; then bootm; fi" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "stdin=serial\0" \ + "stdout=serial\0" \ + "stderr=serial\0" \ + "bootfile=uImage\0" \ + "loadaddr=0x800000\0" \ + "autoload=no\0" \ + "netconsole=" \ + "set stdin $stdin,nc; " \ + "set stdout $stdout,nc; " \ + "set stderr $stderr,nc;\0" \ + "diskload=ide reset && " \ + "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \ + "usbload=usb start && " \ + "fatload usb 0:1 $loadaddr /boot/$bootfile\0" + +#endif /* _CONFIG_NET2BIG_V2_H */