Update the am64 and am642 device-trees from linux v6.6-rc1. This needed the following tweaks to the u-boot specific dtsi as well:

- Switch tick-timer to the main_timer as it's now defined in the main dtsi - Secure proxies are defined in SoC dtsi - Drop duplicate nodes - u-boot.dtsi is included in r5-*.dts, no need for either the definitions from main.dtsi OR duplication from u-boot.dtsi - deal with both am642-evm and am642-sk

Signed-off-by: Roger Quadros rogerq@kernel.org --- arch/arm/dts/k3-am64-main.dtsi | 209 ++++++++++++++++++++++---- arch/arm/dts/k3-am64-mcu.dtsi | 53 ++++++- arch/arm/dts/k3-am64-thermal.dtsi | 33 ++++ arch/arm/dts/k3-am64.dtsi | 22 +-- arch/arm/dts/k3-am642-evm-u-boot.dtsi | 70 +++++---- arch/arm/dts/k3-am642-evm.dts | 177 +++++++++++++++++----- arch/arm/dts/k3-am642-r5-evm.dts | 194 ++---------------------- arch/arm/dts/k3-am642-r5-sk.dts | 194 +----------------------- arch/arm/dts/k3-am642-sk-u-boot.dtsi | 61 ++++---- arch/arm/dts/k3-am642-sk.dts | 174 +++++++++++++++------ arch/arm/dts/k3-am642.dtsi | 1 + arch/arm/dts/k3-serdes.h | 204 +++++++++++++++++++++++++ 12 files changed, 815 insertions(+), 577 deletions(-) create mode 100644 arch/arm/dts/k3-am64-thermal.dtsi create mode 100644 arch/arm/dts/k3-serdes.h

diff --git a/arch/arm/dts/k3-am64-main.dtsi b/arch/arm/dts/k3-am64-main.dtsi index 5e8036f32d..0df54a7418 100644 --- a/arch/arm/dts/k3-am64-main.dtsi +++ b/arch/arm/dts/k3-am64-main.dtsi @@ -44,11 +44,28 @@ #size-cells = <1>; ranges = <0x0 0x0 0x43000000 0x20000>;

+ chipid@14 { + compatible = "ti,am654-chipid"; + reg = <0x00000014 0x4>; + }; + serdes_ln_ctrl: mux-controller { compatible = "mmio-mux"; #mux-control-cells = <1>; mux-reg-masks = <0x4080 0x3>; /* SERDES0 lane0 select */ }; + + phy_gmii_sel: phy@4044 { + compatible = "ti,am654-phy-gmii-sel"; + reg = <0x4044 0x8>; + #phy-cells = <1>; + }; + + epwm_tbclk: clock-controller@4140 { + compatible = "ti,am64-epwm-tbclk"; + reg = <0x4130 0x4>; + #clock-cells = <1>; + }; };

gic500: interrupt-controller@1800000 { @@ -203,29 +220,154 @@ pinctrl-single,function-mask = <0xffffffff>; };

- main_conf: syscon@43000000 { - compatible = "syscon", "simple-mfd"; - reg = <0x00 0x43000000 0x00 0x20000>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x00 0x00 0x43000000 0x20000>; + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 36 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 36 1>; + assigned-clock-parents = <&k3_clks 36 2>; + power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + };

- chipid@14 { - compatible = "ti,am654-chipid"; - reg = <0x00000014 0x4>; - }; + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 37 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 37 1>; + assigned-clock-parents = <&k3_clks 37 2>; + power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + };

- phy_gmii_sel: phy@4044 { - compatible = "ti,am654-phy-gmii-sel"; - reg = <0x4044 0x8>; - #phy-cells = <1>; - }; + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 38 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 38 1>; + assigned-clock-parents = <&k3_clks 38 2>; + power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + };

- epwm_tbclk: clock@4140 { - compatible = "ti,am64-epwm-tbclk", "syscon"; - reg = <0x4130 0x4>; - #clock-cells = <1>; - }; + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 39 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 39 1>; + assigned-clock-parents = <&k3_clks 39 2>; + power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 40 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 40 1>; + assigned-clock-parents = <&k3_clks 40 2>; + power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 41 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 41 1>; + assigned-clock-parents = <&k3_clks 41 2>; + power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 42 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 42 1>; + assigned-clock-parents = <&k3_clks 42 2>; + power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 43 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 43 1>; + assigned-clock-parents = <&k3_clks 43 2>; + power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer8: timer@2480000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2480000 0x00 0x400>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 44 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 44 1>; + assigned-clock-parents = <&k3_clks 44 2>; + power-domains = <&k3_pds 44 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer9: timer@2490000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2490000 0x00 0x400>; + interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 45 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 45 1>; + assigned-clock-parents = <&k3_clks 45 2>; + power-domains = <&k3_pds 45 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer10: timer@24a0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24a0000 0x00 0x400>; + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 46 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 46 1>; + assigned-clock-parents = <&k3_clks 46 2>; + power-domains = <&k3_pds 46 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer11: timer@24b0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24b0000 0x00 0x400>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 47 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 47 1>; + assigned-clock-parents = <&k3_clks 47 2>; + power-domains = <&k3_pds 47 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_esm: esm@420000 { + compatible = "ti,j721e-esm"; + reg = <0x00 0x420000 0x00 0x1000>; + ti,esm-pins = <160>, <161>; };

main_uart0: serial@2800000 { @@ -233,7 +375,6 @@ reg = <0x00 0x02800000 0x00 0x100>; interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 146 0>; clock-names = "fclk"; @@ -245,7 +386,6 @@ reg = <0x00 0x02810000 0x00 0x100>; interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 152 0>; clock-names = "fclk"; @@ -257,7 +397,6 @@ reg = <0x00 0x02820000 0x00 0x100>; interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 153 0>; clock-names = "fclk"; @@ -269,7 +408,6 @@ reg = <0x00 0x02830000 0x00 0x100>; interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 154 0>; clock-names = "fclk"; @@ -281,7 +419,6 @@ reg = <0x00 0x02840000 0x00 0x100>; interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 155 0>; clock-names = "fclk"; @@ -293,7 +430,6 @@ reg = <0x00 0x02850000 0x00 0x100>; interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 156 0>; clock-names = "fclk"; @@ -305,7 +441,6 @@ reg = <0x00 0x02860000 0x00 0x100>; interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 158 0>; clock-names = "fclk"; @@ -590,7 +725,7 @@ pinctrl-single,function-mask = <0x000107ff>; };

- usbss0: cdns-usb@f900000{ + usbss0: cdns-usb@f900000 { compatible = "ti,am64-usb"; reg = <0x00 0xf900000 0x00 0x100>; power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>; @@ -601,7 +736,7 @@ #address-cells = <2>; #size-cells = <2>; ranges; - usb0: usb@f400000{ + usb0: usb@f400000 { compatible = "cdns,usb3"; reg = <0x00 0xf400000 0x00 0x10000>, <0x00 0xf410000 0x00 0x10000>, @@ -630,6 +765,7 @@ assigned-clock-parents = <&k3_clks 0 3>; assigned-clock-rates = <60000000>; clock-names = "fck"; + status = "disabled";

adc { #io-channel-cells = <1>; @@ -659,6 +795,7 @@ assigned-clock-parents = <&k3_clks 75 7>; assigned-clock-rates = <166666666>; power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; };

@@ -676,6 +813,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; };

mailbox0_cluster3: mailbox@29030000 { @@ -686,6 +824,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; };

mailbox0_cluster4: mailbox@29040000 { @@ -696,6 +835,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; };

mailbox0_cluster5: mailbox@29050000 { @@ -706,6 +846,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; };

mailbox0_cluster6: mailbox@29060000 { @@ -715,6 +856,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; };

mailbox0_cluster7: mailbox@29070000 { @@ -724,6 +866,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; };

main_r5fss0: r5fss@78000000 { @@ -1392,4 +1535,12 @@ clock-names = "fck"; status = "disabled"; }; + + main_vtm0: temperature-sensor@b00000 { + compatible = "ti,j7200-vtm"; + reg = <0x00 0xb00000 0x00 0x400>, + <0x00 0xb01000 0x00 0x400>; + power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; }; diff --git a/arch/arm/dts/k3-am64-mcu.dtsi b/arch/arm/dts/k3-am64-mcu.dtsi index 38ddf0b3b8..686d497907 100644 --- a/arch/arm/dts/k3-am64-mcu.dtsi +++ b/arch/arm/dts/k3-am64-mcu.dtsi @@ -6,11 +6,55 @@ */

&cbass_mcu { + /* + * The MCU domain timer interrupts are routed only to the ESM module, + * and not currently available for Linux. The MCU domain timers are + * of limited use without interrupts, and likely reserved by the ESM. + */ + mcu_timer0: timer@4800000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4800000 0x00 0x400>; + clocks = <&k3_clks 35 1>; + clock-names = "fck"; + power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + + mcu_timer1: timer@4810000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4810000 0x00 0x400>; + clocks = <&k3_clks 48 1>; + clock-names = "fck"; + power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + + mcu_timer2: timer@4820000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4820000 0x00 0x400>; + clocks = <&k3_clks 49 1>; + clock-names = "fck"; + power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + + mcu_timer3: timer@4830000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4830000 0x00 0x400>; + clocks = <&k3_clks 50 1>; + clock-names = "fck"; + power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + mcu_uart0: serial@4a00000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x04a00000 0x00 0x100>; interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>; - current-speed = <115200>; power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 149 0>; clock-names = "fclk"; @@ -21,7 +65,6 @@ compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x04a10000 0x00 0x100>; interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; - current-speed = <115200>; power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 160 0>; clock-names = "fclk"; @@ -109,4 +152,10 @@ pinctrl-single,register-width = <32>; pinctrl-single,function-mask = <0xffffffff>; }; + + mcu_esm: esm@4100000 { + compatible = "ti,j721e-esm"; + reg = <0x00 0x4100000 0x00 0x1000>; + ti,esm-pins = <0>, <1>; + }; }; diff --git a/arch/arm/dts/k3-am64-thermal.dtsi b/arch/arm/dts/k3-am64-thermal.dtsi new file mode 100644 index 0000000000..036db56ba7 --- /dev/null +++ b/arch/arm/dts/k3-am64-thermal.dtsi @@ -0,0 +1,33 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include <dt-bindings/thermal/thermal.h> + +thermal_zones: thermal-zones { + main0_thermal: main0-thermal { + polling-delay-passive = <250>; /* milliSeconds */ + polling-delay = <500>; /* milliSeconds */ + thermal-sensors = <&main_vtm0 0>; + + trips { + main0_crit: main0-crit { + temperature = <105000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; + + main1_thermal: main1-thermal { + polling-delay-passive = <250>; /* milliSeconds */ + polling-delay = <500>; /* milliSeconds */ + thermal-sensors = <&main_vtm0 1>; + + trips { + main1_crit: main1-crit { + temperature = <105000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; +}; diff --git a/arch/arm/dts/k3-am64.dtsi b/arch/arm/dts/k3-am64.dtsi index c858725133..8e9c2bc70f 100644 --- a/arch/arm/dts/k3-am64.dtsi +++ b/arch/arm/dts/k3-am64.dtsi @@ -8,9 +8,10 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/pinctrl/k3.h> #include <dt-bindings/soc/ti,sci_pm_domain.h>

+#include "k3-pinctrl.h" + / { model = "Texas Instruments K3 AM642 SoC"; compatible = "ti,am642"; @@ -18,22 +19,6 @@ #address-cells = <2>; #size-cells = <2>;

- aliases { - serial0 = &mcu_uart0; - serial1 = &mcu_uart1; - serial2 = &main_uart0; - serial3 = &main_uart1; - serial4 = &main_uart2; - serial5 = &main_uart3; - serial6 = &main_uart4; - serial7 = &main_uart5; - serial8 = &main_uart6; - ethernet0 = &cpsw_port1; - ethernet1 = &cpsw_port2; - mmc0 = &sdhci0; - mmc1 = &sdhci1; - }; - chosen { };

firmware { @@ -69,6 +54,7 @@ <0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */ <0x00 0x00600000 0x00 0x00600000 0x00 0x00001100>, /* GPIO */ <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* Timesync router */ + <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */ <0x00 0x01000000 0x00 0x01000000 0x00 0x02330400>, /* First peripheral window */ <0x00 0x08000000 0x00 0x08000000 0x00 0x00200000>, /* Main CPSW */ <0x00 0x0d000000 0x00 0x0d000000 0x00 0x00800000>, /* PCIE_CORE */ @@ -105,6 +91,8 @@ ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; /* Peripheral window */ }; }; + + #include "k3-am64-thermal.dtsi" };

/* Now include the peripherals for each bus segments */ diff --git a/arch/arm/dts/k3-am642-evm-u-boot.dtsi b/arch/arm/dts/k3-am642-evm-u-boot.dtsi index 73577e8cfd..f90917d132 100644 --- a/arch/arm/dts/k3-am642-evm-u-boot.dtsi +++ b/arch/arm/dts/k3-am642-evm-u-boot.dtsi @@ -7,8 +7,7 @@

/ { chosen { - stdout-path = "serial2:115200n8"; - tick-timer = &timer1; + tick-timer = &main_timer0; };

memory@80000000 { @@ -16,15 +15,18 @@ }; };

-&cbass_main{ +&cbass_main { bootph-pre-ram; - timer1: timer@2400000 { - compatible = "ti,omap5430-timer"; - reg = <0x0 0x2400000 0x0 0x80>; - ti,timer-alwon; - clock-frequency = <200000000>; - bootph-pre-ram; - }; +}; + +&main_timer0 { + bootph-pre-ram; + clock-frequency = <200000000>; + /delete-property/ clocks; + /delete-property/ clock-names; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ power-domains; };

&main_conf { @@ -36,27 +38,32 @@

&main_pmx0 { bootph-pre-ram; - main_i2c0_pins_default: main-i2c0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ - AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ - >; - }; };

&main_i2c0 { - status = "okay"; bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_i2c0_pins_default>; - clock-frequency = <400000>; +}; + +&main_i2c0_pins_default { + bootph-pre-ram; };

&main_uart0 { bootph-pre-ram; };

+&main_uart0_pins_default { + bootph-pre-ram; +}; + +&main_uart1 { + bootph-pre-ram; +}; + +&main_uart1_pins_default { + bootph-pre-ram; +}; + &usb0 { dr_mode="peripheral"; bootph-pre-ram; @@ -110,19 +117,16 @@ bootph-pre-ram; };

+&main_mmc1_pins_default { + bootph-pre-ram; +}; + &cpsw3g { - reg = <0x0 0x8000000 0x0 0x200000>, - <0x0 0x43000200 0x0 0x8>; - reg-names = "cpsw_nuss", "mac_efuse"; - /delete-property/ ranges; - pinctrl-0 = <&mdio1_pins_default /* HACK: as MDIO driver is not DM enabled */ - &rgmii1_pins_default - &rgmii2_pins_default>; - - cpsw-phy-sel@04044 { - compatible = "ti,am64-phy-gmii-sel"; - reg = <0x0 0x43004044 0x0 0x8>; - }; + bootph-pre-ram; +}; + +&cpsw_port1 { + bootph-pre-ram; };

&cpsw_port2 { diff --git a/arch/arm/dts/k3-am642-evm.dts b/arch/arm/dts/k3-am642-evm.dts index 39feea78a0..b4a1f73d4f 100644 --- a/arch/arm/dts/k3-am642-evm.dts +++ b/arch/arm/dts/k3-am642-evm.dts @@ -6,26 +6,38 @@ /dts-v1/;

#include <dt-bindings/phy/phy.h> -#include <dt-bindings/mux/ti-serdes.h> #include <dt-bindings/leds/common.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/net/ti-dp83867.h> #include "k3-am642.dtsi"

+#include "k3-serdes.h" + / { compatible = "ti,am642-evm", "ti,am642"; model = "Texas Instruments AM642 EVM";

chosen { - stdout-path = "serial2:115200n8"; - bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + stdout-path = &main_uart0; + }; + + aliases { + serial0 = &mcu_uart0; + serial1 = &main_uart1; + serial2 = &main_uart0; + serial3 = &main_uart3; + i2c0 = &main_i2c0; + i2c1 = &main_i2c1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + ethernet0 = &cpsw_port1; + ethernet1 = &cpsw_port2; };

memory@80000000 { device_type = "memory"; /* 2G RAM */ reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - };

reserved-memory { @@ -94,7 +106,7 @@ }; };

- evm_12v0: fixedregulator-evm12v0 { + evm_12v0: regulator-0 { /* main DC jack */ compatible = "regulator-fixed"; regulator-name = "evm_12v0"; @@ -104,7 +116,7 @@ regulator-boot-on; };

- vsys_5v0: fixedregulator-vsys5v0 { + vsys_5v0: regulator-1 { /* output of LM5140 */ compatible = "regulator-fixed"; regulator-name = "vsys_5v0"; @@ -115,7 +127,7 @@ regulator-boot-on; };

- vsys_3v3: fixedregulator-vsys3v3 { + vsys_3v3: regulator-2 { /* output of LM5140 */ compatible = "regulator-fixed"; regulator-name = "vsys_3v3"; @@ -126,7 +138,7 @@ regulator-boot-on; };

- vdd_mmc1: fixed-regulator-sd { + vdd_mmc1: regulator-3 { /* TPS2051BD */ compatible = "regulator-fixed"; regulator-name = "vdd_mmc1"; @@ -138,7 +150,7 @@ gpio = <&exp1 6 GPIO_ACTIVE_HIGH>; };

- vddb: fixedregulator-vddb { + vddb: regulator-4 { compatible = "regulator-fixed"; regulator-name = "vddb_3v3_display"; regulator-min-microvolt = <3300000>; @@ -148,6 +160,20 @@ regulator-boot-on; };

+ vtt_supply: regulator-5 { + compatible = "regulator-fixed"; + regulator-name = "vtt"; + pinctrl-names = "default"; + pinctrl-0 = <&ddr_vtt_pins_default>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; + vin-supply = <&vsys_3v3>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + }; + leds { compatible = "gpio-leds";

@@ -201,7 +227,7 @@ };

&main_pmx0 { - main_mmc1_pins_default: main-mmc1-pins-default { + main_mmc1_pins_default: main-mmc1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ @@ -215,7 +241,16 @@ >; };

- main_uart0_pins_default: main-uart0-pins-default { + main_uart1_pins_default: main-uart1-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ + AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ + AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ + AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ + >; + }; + + main_uart0_pins_default: main-uart0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ @@ -224,7 +259,7 @@ >; };

- main_spi0_pins_default: main-spi0-pins-default { + main_spi0_pins_default: main-spi0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0210, PIN_INPUT, 0) /* (D13) SPI0_CLK */ AM64X_IOPAD(0x0208, PIN_OUTPUT, 0) /* (D12) SPI0_CS0 */ @@ -233,21 +268,28 @@ >; };

- main_i2c1_pins_default: main-i2c1-pins-default { + main_i2c0_pins_default: main-i2c0-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ + AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */ AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */ >; };

- mdio1_pins_default: mdio1-pins-default { + mdio1_pins_default: mdio1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ >; };

- rgmii1_pins_default: rgmii1-pins-default { + rgmii1_pins_default: rgmii1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */ AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */ @@ -264,7 +306,7 @@ >; };

- rgmii2_pins_default: rgmii2-pins-default { + rgmii2_pins_default: rgmii2-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ @@ -281,13 +323,13 @@ >; };

- main_usb0_pins_default: main-usb0-pins-default { + main_usb0_pins_default: main-usb0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ >; };

- ospi0_pins_default: ospi0-pins-default { + ospi0_pins_default: ospi0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */ @@ -303,36 +345,58 @@ >; };

- main_ecap0_pins_default: main-ecap0-pins-default { + main_ecap0_pins_default: main-ecap0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */ >; };

- main_mcan0_pins_default: main-mcan0-pins-default { + main_mcan0_pins_default: main-mcan0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0254, PIN_INPUT, 0) /* (B17) MCAN0_RX */ AM64X_IOPAD(0x0250, PIN_OUTPUT, 0) /* (A17) MCAN0_TX */ >; };

- main_mcan1_pins_default: main-mcan1-pins-default { + main_mcan1_pins_default: main-mcan1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x025c, PIN_INPUT, 0) /* (D17) MCAN1_RX */ AM64X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (C17) MCAN1_TX */ >; }; + + ddr_vtt_pins_default: ddr-vtt-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7) /* (L18) OSPI0_CSN1.GPIO0_12 */ + >; + }; };

&main_uart0 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&main_uart0_pins_default>; + current-speed = <115200>; };

/* main_uart1 is reserved for firmware usage */ &main_uart1 { status = "reserved"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart1_pins_default>; +}; + +&main_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@50 { + /* AT24CM01 */ + compatible = "atmel,24c1024"; + reg = <0x50>; + }; };

&main_i2c1 { @@ -425,8 +489,7 @@

&cpsw3g { pinctrl-names = "default"; - pinctrl-0 = <&rgmii1_pins_default - &rgmii2_pins_default>; + pinctrl-0 = <&rgmii1_pins_default>, <&rgmii2_pins_default>; };

&cpsw_port1 { @@ -457,6 +520,7 @@ };

&ospi0 { + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&ospi0_pins_default>;

@@ -471,10 +535,53 @@ cdns,tchsh-ns = <60>; cdns,tslch-ns = <60>; cdns,read-delay = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ospi.tiboot3"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "ospi.tispl"; + reg = <0x100000 0x200000>; + }; + + partition@300000 { + label = "ospi.u-boot"; + reg = <0x300000 0x400000>; + }; + + partition@700000 { + label = "ospi.env"; + reg = <0x700000 0x40000>; + }; + + partition@740000 { + label = "ospi.env.backup"; + reg = <0x740000 0x40000>; + }; + + partition@800000 { + label = "ospi.rootfs"; + reg = <0x800000 0x37c0000>; + }; + + partition@3fc0000 { + label = "ospi.phypattern"; + reg = <0x3fc0000 0x40000>; + }; + }; }; };

&mailbox0_cluster2 { + status = "okay"; + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; @@ -486,11 +593,9 @@ }; };

-&mailbox0_cluster3 { - status = "disabled"; -}; - &mailbox0_cluster4 { + status = "okay"; + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; @@ -502,41 +607,35 @@ }; };

-&mailbox0_cluster5 { - status = "disabled"; -}; - &mailbox0_cluster6 { + status = "okay"; + mbox_m4_0: mbox-m4-0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; }; };

-&mailbox0_cluster7 { - status = "disabled"; -}; - &main_r5fss0_core0 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core0>; memory-region = <&main_r5fss0_core0_dma_memory_region>, <&main_r5fss0_core0_memory_region>; };

&main_r5fss0_core1 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core1>; memory-region = <&main_r5fss0_core1_dma_memory_region>, <&main_r5fss0_core1_memory_region>; };

&main_r5fss1_core0 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core0>; memory-region = <&main_r5fss1_core0_dma_memory_region>, <&main_r5fss1_core0_memory_region>; };

&main_r5fss1_core1 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core1>; memory-region = <&main_r5fss1_core1_dma_memory_region>, <&main_r5fss1_core1_memory_region>; }; diff --git a/arch/arm/dts/k3-am642-r5-evm.dts b/arch/arm/dts/k3-am642-r5-evm.dts index b49064181a..a5fe5db2d1 100644 --- a/arch/arm/dts/k3-am642-r5-evm.dts +++ b/arch/arm/dts/k3-am642-r5-evm.dts @@ -5,30 +5,18 @@

/dts-v1/;

-#include "k3-am642.dtsi" +#include "k3-am642-evm.dts" #include "k3-am64-evm-ddr4-1600MTs.dtsi" #include "k3-am64-ddr.dtsi" -#include "k3-am64x-binman.dtsi"

-/ { - chosen { - stdout-path = "serial2:115200n8"; - tick-timer = &timer1; - }; +#include "k3-am642-evm-u-boot.dtsi"

+/ { aliases { remoteproc0 = &sysctrler; remoteproc1 = &a53_0; };

- memory@80000000 { - device_type = "memory"; - /* 2G RAM */ - reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - - bootph-pre-ram; - }; - a53_0: a53@0 { compatible = "ti,am654-rproc"; reg = <0x00 0x00a90000 0x00 0x10>; @@ -46,34 +34,12 @@ bootph-pre-ram; };

- reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - secure_ddr: optee@9e800000 { - reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ - alignment = <0x1000>; - no-map; - }; - }; - clk_200mhz: dummy-clock-200mhz { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <200000000>; bootph-pre-ram; }; - - vtt_supply: vtt-supply { - compatible = "regulator-gpio"; - regulator-name = "vtt"; - regulator-min-microvolt = <0>; - regulator-max-microvolt = <3300000>; - gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; - states = <0 0x0 3300000 0x1>; - bootph-pre-ram; - }; };

&cbass_main { @@ -85,131 +51,20 @@ }; };

-&cbass_main { - main_esm: esm@420000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x420000 0x0 0x1000>; - ti,esm-pins = <160>, <161>; - bootph-pre-ram; - }; +&main_esm { + bootph-pre-ram; };

&cbass_mcu { bootph-pre-ram; - mcu_esm: esm@4100000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x4100000 0x0 0x1000>; - ti,esm-pins = <0>, <1>; - bootph-pre-ram; - }; };

-&main_pmx0 { +&mcu_esm { bootph-pre-ram; - main_uart0_pins_default: main-uart0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ - AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ - AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */ - AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ - >; - }; - - main_uart1_pins_default: main-uart1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ - AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ - AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ - AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ - >; - }; - - main_mmc0_pins_default: main-mmc0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */ - AM64X_IOPAD(0x01aC, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */ - AM64X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */ - AM64X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */ - AM64X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */ - AM64X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */ - AM64X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */ - AM64X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */ - AM64X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */ - AM64X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */ - AM64X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */ - >; - }; - - main_mmc1_pins_default: main-mmc1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ - AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ - AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ - AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ - AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ - AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ - AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ - AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */ - >; - }; - - ddr_vtt_pins_default: ddr-vtt-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7) /* (L18) OSPI0_CSN1.GPIO0_12 */ - >; - }; - - main_usb0_pins_default: main-usb0-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ - >; - }; - - mdio1_pins_default: mdio1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ - AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ - >; - }; - - rgmii1_pins_default: rgmii1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */ - AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */ - AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* (V6) PRG0_PRU1_GPO10.RGMII1_RD2 */ - AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */ - AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* (AA5) PRG0_PRU0_GPO10.RGMII1_RXC */ - AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* (W6) PRG0_PRU0_GPO9.RGMII1_RX_CTL */ - AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ - AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ - AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ - AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ - AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ - AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ - >; - }; +};

- rgmii2_pins_default: rgmii2-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ - AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ - AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */ - AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */ - AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */ - AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */ - AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */ - AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */ - AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */ - AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */ - AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */ - AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */ - >; - }; +&main_pmx0 { + bootph-pre-ram; };

&dmsc { @@ -225,39 +80,22 @@ /delete-property/ power-domains; /delete-property/ clocks; /delete-property/ clock-names; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart0_pins_default>; - status = "okay"; -}; - -&main_uart1 { - bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart1_pins_default>; };

&memorycontroller { vtt-supply = <&vtt_supply>; - pinctrl-names = "default"; - pinctrl-0 = <&ddr_vtt_pins_default>; };

&sdhci0 { /delete-property/ power-domains; clocks = <&clk_200mhz>; clock-names = "clk_xin"; - ti,driver-strength-ohm = <50>; - disable-wp; - pinctrl-0 = <&main_mmc0_pins_default>; };

&sdhci1 { /delete-property/ power-domains; clocks = <&clk_200mhz>; clock-names = "clk_xin"; - ti,driver-strength-ohm = <50>; - disable-wp; - pinctrl-0 = <&main_mmc1_pins_default>; };

&main_gpio0 { @@ -269,17 +107,3 @@ &main_i2c0 { /delete-property/ power-domains; }; - -&usbss0 { - ti,vbus-divider; - ti,usb2-only; -}; - -&usb0 { - dr_mode = "otg"; - maximum-speed = "high-speed"; - pinctrl-names = "default"; - pinctrl-0 = <&main_usb0_pins_default>; -}; - -#include "k3-am642-evm-u-boot.dtsi" diff --git a/arch/arm/dts/k3-am642-r5-sk.dts b/arch/arm/dts/k3-am642-r5-sk.dts index 32d4c31728..5482e7f153 100644 --- a/arch/arm/dts/k3-am642-r5-sk.dts +++ b/arch/arm/dts/k3-am642-r5-sk.dts @@ -5,31 +5,18 @@

/dts-v1/;

-#include <dt-bindings/mux/ti-serdes.h> -#include <dt-bindings/phy/phy.h> -#include <dt-bindings/net/ti-dp83867.h> -#include "k3-am642.dtsi" +#include "k3-am642-sk.dts" #include "k3-am64-sk-lp4-1600MTs.dtsi" #include "k3-am64-ddr.dtsi"

-/ { - chosen { - stdout-path = "serial2:115200n8"; - tick-timer = &timer1; - }; +#include "k3-am642-sk-u-boot.dtsi"

+/ { aliases { remoteproc0 = &sysctrler; remoteproc1 = &a53_0; };

- memory@80000000 { - device_type = "memory"; - /* 2G RAM */ - reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - bootph-pre-ram; - }; - a53_0: a53@0 { compatible = "ti,am654-rproc"; reg = <0x00 0x00a90000 0x00 0x10>; @@ -47,18 +34,6 @@ bootph-pre-ram; };

- reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - secure_ddr: optee@9e800000 { - reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ - alignment = <0x1000>; - no-map; - }; - }; - clk_200mhz: dummy-clock-200mhz { compatible = "fixed-clock"; #clock-cells = <0>; @@ -76,108 +51,16 @@ }; };

-&cbass_main { - main_esm: esm@420000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x420000 0x0 0x1000>; - ti,esm-pins = <160>, <161>; - bootph-pre-ram; - }; +&main_esm { + bootph-pre-ram; };

&cbass_mcu { bootph-pre-ram; - mcu_esm: esm@4100000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x4100000 0x0 0x1000>; - ti,esm-pins = <0>, <1>; - bootph-pre-ram; - }; };

-&main_pmx0 { +&mcu_esm { bootph-pre-ram; - main_uart0_pins_default: main-uart0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ - AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ - AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */ - AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ - >; - }; - - main_uart1_pins_default: main-uart1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ - AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ - AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ - AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ - >; - }; - - main_mmc1_pins_default: main-mmc1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ - AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ - AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ - AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ - AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ - AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ - AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ - AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */ - >; - }; - - main_usb0_pins_default: main-usb0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ - >; - }; - - mdio1_pins_default: mdio1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ - AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ - >; - }; - - rgmii1_pins_default: rgmii1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x011c, PIN_INPUT, 4) /* (AA13) PRG1_PRU1_GPO5.RGMII1_RD0 */ - AM64X_IOPAD(0x0128, PIN_INPUT, 4) /* (U12) PRG1_PRU1_GPO8.RGMII1_RD1 */ - AM64X_IOPAD(0x0150, PIN_INPUT, 4) /* (Y13) PRG1_PRU1_GPO18.RGMII1_RD2 */ - AM64X_IOPAD(0x0154, PIN_INPUT, 4) /* (V12) PRG1_PRU1_GPO19.RGMII1_RD3 */ - AM64X_IOPAD(0x00d8, PIN_INPUT, 4) /* (W13) PRG1_PRU0_GPO8.RGMII1_RXC */ - AM64X_IOPAD(0x00cc, PIN_INPUT, 4) /* (V13) PRG1_PRU0_GPO5.RGMII1_RX_CTL */ - AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ - AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ - AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ - AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ - AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ - AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ - >; - }; - - rgmii2_pins_default: rgmii2-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ - AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ - AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */ - AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */ - AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */ - AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */ - AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */ - AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */ - AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */ - AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */ - AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */ - AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */ - >; - }; };

&dmsc { @@ -193,75 +76,10 @@ /delete-property/ power-domains; /delete-property/ clocks; /delete-property/ clock-names; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart0_pins_default>; - status = "okay"; -}; - -&main_uart1 { - bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart1_pins_default>; };

&sdhci1 { /delete-property/ power-domains; clocks = <&clk_200mhz>; clock-names = "clk_xin"; - ti,driver-strength-ohm = <50>; - disable-wp; - pinctrl-0 = <&main_mmc1_pins_default>; -}; - -&serdes_ln_ctrl { - idle-states = <AM64_SERDES0_LANE0_USB>; -}; - -&serdes_wiz0 { - status = "okay"; -}; - -&serdes0 { - serdes0_usb_link: link@0 { - reg = <0>; - cdns,num-lanes = <1>; - #phy-cells = <0>; - cdns,phy-type = <PHY_TYPE_USB3>; - resets = <&serdes_wiz0 1>; - }; -}; - -&usbss0 { - ti,vbus-divider; -}; - -&usb0 { - dr_mode = "host"; - maximum-speed = "super-speed"; - pinctrl-names = "default"; - pinctrl-0 = <&main_usb0_pins_default>; - phys = <&serdes0_usb_link>; - phy-names = "cdns3,usb3-phy"; -}; - -&cpsw3g { - pinctrl-names = "default"; - pinctrl-0 = <&mdio1_pins_default - &rgmii1_pins_default - &rgmii2_pins_default>; }; - -&cpsw_port2 { - phy-mode = "rgmii-rxid"; - phy-handle = <&cpsw3g_phy1>; -}; - -&cpsw3g_mdio { - cpsw3g_phy1: ethernet-phy@1 { - reg = <1>; - ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; - ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; - }; -}; - -#include "k3-am642-sk-u-boot.dtsi" diff --git a/arch/arm/dts/k3-am642-sk-u-boot.dtsi b/arch/arm/dts/k3-am642-sk-u-boot.dtsi index 4431750dc6..712da56740 100644 --- a/arch/arm/dts/k3-am642-sk-u-boot.dtsi +++ b/arch/arm/dts/k3-am642-sk-u-boot.dtsi @@ -7,12 +7,7 @@

/ { chosen { - stdout-path = "serial2:115200n8"; - tick-timer = &timer1; - }; - - aliases { - mmc1 = &sdhci1; + tick-timer = &main_timer0; };

memory@80000000 { @@ -22,13 +17,16 @@

&cbass_main{ bootph-pre-ram; - timer1: timer@2400000 { - compatible = "ti,omap5430-timer"; - reg = <0x0 0x2400000 0x0 0x80>; - ti,timer-alwon; - clock-frequency = <200000000>; - bootph-pre-ram; - }; +}; + +&main_timer0 { + bootph-pre-ram; + clock-frequency = <200000000>; + /delete-property/ clocks; + /delete-property/ clock-names; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ power-domains; };

&main_conf { @@ -40,26 +38,32 @@

&main_pmx0 { bootph-pre-ram; - main_i2c0_pins_default: main-i2c0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ - AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ - >; - }; +}; + +&main_i2c0_pins_default { + bootph-pre-ram; };

&main_i2c0 { bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_i2c0_pins_default>; - clock-frequency = <400000>; };

&main_uart0 { bootph-pre-ram; };

+&main_uart0_pins_default { + bootph-pre-ram; +}; + +&main_uart1 { + bootph-pre-ram; +}; + +&main_uart1_pins_default { + bootph-pre-ram; +}; + &dmss { bootph-pre-ram; }; @@ -102,18 +106,8 @@ };

&cpsw3g { - reg = <0x0 0x8000000 0x0 0x200000>, - <0x0 0x43000200 0x0 0x8>; - reg-names = "cpsw_nuss", "mac_efuse"; - /delete-property/ ranges; bootph-pre-ram;

- cpsw-phy-sel@04044 { - compatible = "ti,am64-phy-gmii-sel"; - reg = <0x0 0x43004044 0x0 0x8>; - bootph-pre-ram; - }; - ethernet-ports { bootph-pre-ram; }; @@ -160,7 +154,6 @@ };

&usb0 { - dr_mode = "host"; bootph-pre-ram; };

diff --git a/arch/arm/dts/k3-am642-sk.dts b/arch/arm/dts/k3-am642-sk.dts index 2e2d40da36..722fd285a3 100644 --- a/arch/arm/dts/k3-am642-sk.dts +++ b/arch/arm/dts/k3-am642-sk.dts @@ -5,27 +5,38 @@

/dts-v1/;

-#include <dt-bindings/mux/ti-serdes.h> #include <dt-bindings/phy/phy.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/net/ti-dp83867.h> #include <dt-bindings/leds/common.h> #include "k3-am642.dtsi"

+#include "k3-serdes.h" + / { compatible = "ti,am642-sk", "ti,am642"; model = "Texas Instruments AM642 SK";

chosen { - stdout-path = "serial2:115200n8"; - bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + stdout-path = &main_uart0; + }; + + aliases { + serial0 = &mcu_uart0; + serial1 = &main_uart1; + serial2 = &main_uart0; + i2c0 = &main_i2c0; + i2c1 = &main_i2c1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + ethernet0 = &cpsw_port1; + ethernet1 = &cpsw_port2; };

memory@80000000 { device_type = "memory"; /* 2G RAM */ reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - };

reserved-memory { @@ -94,7 +105,7 @@ }; };

- vusb_main: fixed-regulator-vusb-main5v0 { + vusb_main: regulator-0 { /* USB MAIN INPUT 5V DC */ compatible = "regulator-fixed"; regulator-name = "vusb_main5v0"; @@ -104,7 +115,7 @@ regulator-boot-on; };

- vcc_3v3_sys: fixedregulator-vcc-3v3-sys { + vcc_3v3_sys: regulator-1 { /* output of LP8733xx */ compatible = "regulator-fixed"; regulator-name = "vcc_3v3_sys"; @@ -115,7 +126,7 @@ regulator-boot-on; };

- vdd_mmc1: fixed-regulator-sd { + vdd_mmc1: regulator-2 { /* TPS2051BD */ compatible = "regulator-fixed"; regulator-name = "vdd_mmc1"; @@ -127,7 +138,7 @@ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>; };

- com8_ls_en: regulator-1 { + com8_ls_en: regulator-3 { compatible = "regulator-fixed"; regulator-name = "com8_ls_en"; regulator-min-microvolt = <3300000>; @@ -139,7 +150,7 @@ gpio = <&main_gpio0 62 GPIO_ACTIVE_LOW>; };

- wlan_en: regulator-2 { + wlan_en: regulator-4 { /* output of SN74AVC4T245RSVR */ compatible = "regulator-fixed"; regulator-name = "wlan_en"; @@ -222,20 +233,21 @@ };

&main_pmx0 { - main_mmc1_pins_default: main-mmc1-pins-default { + main_mmc1_pins_default: main-mmc1-default-pins { pinctrl-single,pins = < - AM64X_IOPAD(0x0294, PIN_INPUT, 0) /* (J19) MMC1_CMD */ + AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */ + AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ + AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* (#N/A) MMC1_CLKLB */ - AM64X_IOPAD(0x028c, PIN_INPUT, 0) /* (L20) MMC1_CLK */ - AM64X_IOPAD(0x0288, PIN_INPUT, 0) /* (K21) MMC1_DAT0 */ - AM64X_IOPAD(0x0284, PIN_INPUT, 0) /* (L21) MMC1_DAT1 */ - AM64X_IOPAD(0x0280, PIN_INPUT, 0) /* (K19) MMC1_DAT2 */ - AM64X_IOPAD(0x027c, PIN_INPUT, 0) /* (K18) MMC1_DAT3 */ - AM64X_IOPAD(0x0298, PIN_INPUT, 0) /* (D19) MMC1_SDCD */ + AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ + AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ + AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ + AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ + AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ >; };

- main_uart0_pins_default: main-uart0-pins-default { + main_uart0_pins_default: main-uart0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ @@ -244,27 +256,43 @@ >; };

- main_usb0_pins_default: main-usb0-pins-default { + main_uart1_pins_default: main-uart1-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ + AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ + AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ + AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ + >; + }; + + main_usb0_pins_default: main-usb0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ >; };

- main_i2c1_pins_default: main-i2c1-pins-default { + main_i2c0_pins_default: main-i2c0-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ + AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */ AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */ >; };

- mdio1_pins_default: mdio1-pins-default { + mdio1_pins_default: mdio1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ >; };

- rgmii1_pins_default: rgmii1-pins-default { + rgmii1_pins_default: rgmii1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x011c, PIN_INPUT, 4) /* (AA13) PRG1_PRU1_GPO5.RGMII1_RD0 */ AM64X_IOPAD(0x0128, PIN_INPUT, 4) /* (U12) PRG1_PRU1_GPO8.RGMII1_RD1 */ @@ -281,7 +309,7 @@ >; };

- rgmii2_pins_default: rgmii2-pins-default { + rgmii2_pins_default: rgmii2-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ @@ -298,7 +326,7 @@ >; };

- ospi0_pins_default: ospi0-pins-default { + ospi0_pins_default: ospi0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */ @@ -314,24 +342,24 @@ >; };

- main_ecap0_pins_default: main-ecap0-pins-default { + main_ecap0_pins_default: main-ecap0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */ >; }; - main_wlan_en_pins_default: main-wlan-en-pins-default { + main_wlan_en_pins_default: main-wlan-en-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x00c4, PIN_OUTPUT_PULLUP, 7) /* (V8) GPIO0_48 */ >; };

- main_com8_ls_en_pins_default: main-com8-ls-en-pins-default { + main_com8_ls_en_pins_default: main-com8-ls-en-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x00fc, PIN_OUTPUT, 7) /* (U7) PRG1_PRU0_GPO17.GPIO0_62 */ >; };

- main_wlan_pins_default: main-wlan-pins-default { + main_wlan_pins_default: main-wlan-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */ >; @@ -342,11 +370,26 @@ status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&main_uart0_pins_default>; + current-speed = <115200>; };

&main_uart1 { /* main_uart1 is reserved for firmware usage */ status = "reserved"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart1_pins_default>; +}; + +&main_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@51 { + compatible = "atmel,24c512"; + reg = <0x51>; + }; };

&main_i2c1 { @@ -439,8 +482,7 @@

&cpsw3g { pinctrl-names = "default"; - pinctrl-0 = <&rgmii1_pins_default - &rgmii2_pins_default>; + pinctrl-0 = <&rgmii1_pins_default>, <&rgmii2_pins_default>; };

&cpsw_port1 { @@ -471,11 +513,8 @@ }; };

-&tscadc0 { - status = "disabled"; -}; - &ospi0 { + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&ospi0_pins_default>;

@@ -490,10 +529,53 @@ cdns,tchsh-ns = <60>; cdns,tslch-ns = <60>; cdns,read-delay = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ospi.tiboot3"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "ospi.tispl"; + reg = <0x100000 0x200000>; + }; + + partition@300000 { + label = "ospi.u-boot"; + reg = <0x300000 0x400000>; + }; + + partition@700000 { + label = "ospi.env"; + reg = <0x700000 0x40000>; + }; + + partition@740000 { + label = "ospi.env.backup"; + reg = <0x740000 0x40000>; + }; + + partition@800000 { + label = "ospi.rootfs"; + reg = <0x800000 0x37c0000>; + }; + + partition@3fc0000 { + label = "ospi.phypattern"; + reg = <0x3fc0000 0x40000>; + }; + }; }; };

&mailbox0_cluster2 { + status = "okay"; + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; @@ -505,11 +587,9 @@ }; };

-&mailbox0_cluster3 { - status = "disabled"; -}; - &mailbox0_cluster4 { + status = "okay"; + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; @@ -521,41 +601,35 @@ }; };

-&mailbox0_cluster5 { - status = "disabled"; -}; - &mailbox0_cluster6 { + status = "okay"; + mbox_m4_0: mbox-m4-0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; }; };

-&mailbox0_cluster7 { - status = "disabled"; -}; - &main_r5fss0_core0 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core0>; memory-region = <&main_r5fss0_core0_dma_memory_region>, <&main_r5fss0_core0_memory_region>; };

&main_r5fss0_core1 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core1>; memory-region = <&main_r5fss0_core1_dma_memory_region>, <&main_r5fss0_core1_memory_region>; };

&main_r5fss1_core0 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core0>; memory-region = <&main_r5fss1_core0_dma_memory_region>, <&main_r5fss1_core0_memory_region>; };

&main_r5fss1_core1 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core1>; memory-region = <&main_r5fss1_core1_dma_memory_region>, <&main_r5fss1_core1_memory_region>; }; diff --git a/arch/arm/dts/k3-am642.dtsi b/arch/arm/dts/k3-am642.dtsi index 8a76f4821b..7a6eedea3a 100644 --- a/arch/arm/dts/k3-am642.dtsi +++ b/arch/arm/dts/k3-am642.dtsi @@ -58,6 +58,7 @@ L2_0: l2-cache0 { compatible = "cache"; cache-level = <2>; + cache-unified; cache-size = <0x40000>; cache-line-size = <64>; cache-sets = <256>; diff --git a/arch/arm/dts/k3-serdes.h b/arch/arm/dts/k3-serdes.h new file mode 100644 index 0000000000..29167f85c1 --- /dev/null +++ b/arch/arm/dts/k3-serdes.h @@ -0,0 +1,204 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * This header provides constants for SERDES MUX for TI SoCs + * + * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/ + */ + +#ifndef DTS_ARM64_TI_K3_SERDES_H +#define DTS_ARM64_TI_K3_SERDES_H + +/* J721E */ + +#define J721E_SERDES0_LANE0_QSGMII_LANE1 0x0 +#define J721E_SERDES0_LANE0_PCIE0_LANE0 0x1 +#define J721E_SERDES0_LANE0_USB3_0_SWAP 0x2 +#define J721E_SERDES0_LANE0_IP4_UNUSED 0x3 + +#define J721E_SERDES0_LANE1_QSGMII_LANE2 0x0 +#define J721E_SERDES0_LANE1_PCIE0_LANE1 0x1 +#define J721E_SERDES0_LANE1_USB3_0 0x2 +#define J721E_SERDES0_LANE1_IP4_UNUSED 0x3 + +#define J721E_SERDES1_LANE0_QSGMII_LANE3 0x0 +#define J721E_SERDES1_LANE0_PCIE1_LANE0 0x1 +#define J721E_SERDES1_LANE0_USB3_1_SWAP 0x2 +#define J721E_SERDES1_LANE0_SGMII_LANE0 0x3 + +#define J721E_SERDES1_LANE1_QSGMII_LANE4 0x0 +#define J721E_SERDES1_LANE1_PCIE1_LANE1 0x1 +#define J721E_SERDES1_LANE1_USB3_1 0x2 +#define J721E_SERDES1_LANE1_SGMII_LANE1 0x3 + +#define J721E_SERDES2_LANE0_IP1_UNUSED 0x0 +#define J721E_SERDES2_LANE0_PCIE2_LANE0 0x1 +#define J721E_SERDES2_LANE0_USB3_1_SWAP 0x2 +#define J721E_SERDES2_LANE0_SGMII_LANE0 0x3 + +#define J721E_SERDES2_LANE1_IP1_UNUSED 0x0 +#define J721E_SERDES2_LANE1_PCIE2_LANE1 0x1 +#define J721E_SERDES2_LANE1_USB3_1 0x2 +#define J721E_SERDES2_LANE1_SGMII_LANE1 0x3 + +#define J721E_SERDES3_LANE0_IP1_UNUSED 0x0 +#define J721E_SERDES3_LANE0_PCIE3_LANE0 0x1 +#define J721E_SERDES3_LANE0_USB3_0_SWAP 0x2 +#define J721E_SERDES3_LANE0_IP4_UNUSED 0x3 + +#define J721E_SERDES3_LANE1_IP1_UNUSED 0x0 +#define J721E_SERDES3_LANE1_PCIE3_LANE1 0x1 +#define J721E_SERDES3_LANE1_USB3_0 0x2 +#define J721E_SERDES3_LANE1_IP4_UNUSED 0x3 + +#define J721E_SERDES4_LANE0_EDP_LANE0 0x0 +#define J721E_SERDES4_LANE0_IP2_UNUSED 0x1 +#define J721E_SERDES4_LANE0_QSGMII_LANE5 0x2 +#define J721E_SERDES4_LANE0_IP4_UNUSED 0x3 + +#define J721E_SERDES4_LANE1_EDP_LANE1 0x0 +#define J721E_SERDES4_LANE1_IP2_UNUSED 0x1 +#define J721E_SERDES4_LANE1_QSGMII_LANE6 0x2 +#define J721E_SERDES4_LANE1_IP4_UNUSED 0x3 + +#define J721E_SERDES4_LANE2_EDP_LANE2 0x0 +#define J721E_SERDES4_LANE2_IP2_UNUSED 0x1 +#define J721E_SERDES4_LANE2_QSGMII_LANE7 0x2 +#define J721E_SERDES4_LANE2_IP4_UNUSED 0x3 + +#define J721E_SERDES4_LANE3_EDP_LANE3 0x0 +#define J721E_SERDES4_LANE3_IP2_UNUSED 0x1 +#define J721E_SERDES4_LANE3_QSGMII_LANE8 0x2 +#define J721E_SERDES4_LANE3_IP4_UNUSED 0x3 + +/* J7200 */ + +#define J7200_SERDES0_LANE0_QSGMII_LANE3 0x0 +#define J7200_SERDES0_LANE0_PCIE1_LANE0 0x1 +#define J7200_SERDES0_LANE0_IP3_UNUSED 0x2 +#define J7200_SERDES0_LANE0_IP4_UNUSED 0x3 + +#define J7200_SERDES0_LANE1_QSGMII_LANE4 0x0 +#define J7200_SERDES0_LANE1_PCIE1_LANE1 0x1 +#define J7200_SERDES0_LANE1_IP3_UNUSED 0x2 +#define J7200_SERDES0_LANE1_IP4_UNUSED 0x3 + +#define J7200_SERDES0_LANE2_QSGMII_LANE1 0x0 +#define J7200_SERDES0_LANE2_PCIE1_LANE2 0x1 +#define J7200_SERDES0_LANE2_IP3_UNUSED 0x2 +#define J7200_SERDES0_LANE2_IP4_UNUSED 0x3 + +#define J7200_SERDES0_LANE3_QSGMII_LANE2 0x0 +#define J7200_SERDES0_LANE3_PCIE1_LANE3 0x1 +#define J7200_SERDES0_LANE3_USB 0x2 +#define J7200_SERDES0_LANE3_IP4_UNUSED 0x3 + +/* AM64 */ + +#define AM64_SERDES0_LANE0_PCIE0 0x0 +#define AM64_SERDES0_LANE0_USB 0x1 + +/* J721S2 */ + +#define J721S2_SERDES0_LANE0_EDP_LANE0 0x0 +#define J721S2_SERDES0_LANE0_PCIE1_LANE0 0x1 +#define J721S2_SERDES0_LANE0_IP3_UNUSED 0x2 +#define J721S2_SERDES0_LANE0_IP4_UNUSED 0x3 + +#define J721S2_SERDES0_LANE1_EDP_LANE1 0x0 +#define J721S2_SERDES0_LANE1_PCIE1_LANE1 0x1 +#define J721S2_SERDES0_LANE1_USB 0x2 +#define J721S2_SERDES0_LANE1_IP4_UNUSED 0x3 + +#define J721S2_SERDES0_LANE2_EDP_LANE2 0x0 +#define J721S2_SERDES0_LANE2_PCIE1_LANE2 0x1 +#define J721S2_SERDES0_LANE2_IP3_UNUSED 0x2 +#define J721S2_SERDES0_LANE2_IP4_UNUSED 0x3 + +#define J721S2_SERDES0_LANE3_EDP_LANE3 0x0 +#define J721S2_SERDES0_LANE3_PCIE1_LANE3 0x1 +#define J721S2_SERDES0_LANE3_USB 0x2 +#define J721S2_SERDES0_LANE3_IP4_UNUSED 0x3 + +/* J784S4 */ + +#define J784S4_SERDES0_LANE0_IP1_UNUSED 0x0 +#define J784S4_SERDES0_LANE0_PCIE1_LANE0 0x1 +#define J784S4_SERDES0_LANE0_IP3_UNUSED 0x2 +#define J784S4_SERDES0_LANE0_IP4_UNUSED 0x3 + +#define J784S4_SERDES0_LANE1_IP1_UNUSED 0x0 +#define J784S4_SERDES0_LANE1_PCIE1_LANE1 0x1 +#define J784S4_SERDES0_LANE1_IP3_UNUSED 0x2 +#define J784S4_SERDES0_LANE1_IP4_UNUSED 0x3 + +#define J784S4_SERDES0_LANE2_PCIE3_LANE0 0x0 +#define J784S4_SERDES0_LANE2_PCIE1_LANE2 0x1 +#define J784S4_SERDES0_LANE2_IP3_UNUSED 0x2 +#define J784S4_SERDES0_LANE2_IP4_UNUSED 0x3 + +#define J784S4_SERDES0_LANE3_PCIE3_LANE1 0x0 +#define J784S4_SERDES0_LANE3_PCIE1_LANE3 0x1 +#define J784S4_SERDES0_LANE3_USB 0x2 +#define J784S4_SERDES0_LANE3_IP4_UNUSED 0x3 + +#define J784S4_SERDES1_LANE0_QSGMII_LANE3 0x0 +#define J784S4_SERDES1_LANE0_PCIE0_LANE0 0x1 +#define J784S4_SERDES1_LANE0_IP3_UNUSED 0x2 +#define J784S4_SERDES1_LANE0_IP4_UNUSED 0x3 + +#define J784S4_SERDES1_LANE1_QSGMII_LANE4 0x0 +#define J784S4_SERDES1_LANE1_PCIE0_LANE1 0x1 +#define J784S4_SERDES1_LANE1_IP3_UNUSED 0x2 +#define J784S4_SERDES1_LANE1_IP4_UNUSED 0x3 + +#define J784S4_SERDES1_LANE2_QSGMII_LANE1 0x0 +#define J784S4_SERDES1_LANE2_PCIE0_LANE2 0x1 +#define J784S4_SERDES1_LANE2_PCIE2_LANE0 0x2 +#define J784S4_SERDES1_LANE2_IP4_UNUSED 0x3 + +#define J784S4_SERDES1_LANE3_QSGMII_LANE2 0x0 +#define J784S4_SERDES1_LANE3_PCIE0_LANE3 0x1 +#define J784S4_SERDES1_LANE3_PCIE2_LANE1 0x2 +#define J784S4_SERDES1_LANE3_IP4_UNUSED 0x3 + +#define J784S4_SERDES2_LANE0_QSGMII_LANE5 0x0 +#define J784S4_SERDES2_LANE0_IP2_UNUSED 0x1 +#define J784S4_SERDES2_LANE0_IP3_UNUSED 0x2 +#define J784S4_SERDES2_LANE0_IP4_UNUSED 0x3 + +#define J784S4_SERDES2_LANE1_QSGMII_LANE6 0x0 +#define J784S4_SERDES2_LANE1_IP2_UNUSED 0x1 +#define J784S4_SERDES2_LANE1_IP3_UNUSED 0x2 +#define J784S4_SERDES2_LANE1_IP4_UNUSED 0x3 + +#define J784S4_SERDES2_LANE2_QSGMII_LANE7 0x0 +#define J784S4_SERDES2_LANE2_QSGMII_LANE1 0x1 +#define J784S4_SERDES2_LANE2_IP3_UNUSED 0x2 +#define J784S4_SERDES2_LANE2_IP4_UNUSED 0x3 + +#define J784S4_SERDES2_LANE3_QSGMII_LANE8 0x0 +#define J784S4_SERDES2_LANE3_QSGMII_LANE2 0x1 +#define J784S4_SERDES2_LANE3_IP3_UNUSED 0x2 +#define J784S4_SERDES2_LANE3_IP4_UNUSED 0x3 + +#define J784S4_SERDES4_LANE0_EDP_LANE0 0x0 +#define J784S4_SERDES4_LANE0_QSGMII_LANE5 0x1 +#define J784S4_SERDES4_LANE0_IP3_UNUSED 0x2 +#define J784S4_SERDES4_LANE0_IP4_UNUSED 0x3 + +#define J784S4_SERDES4_LANE1_EDP_LANE1 0x0 +#define J784S4_SERDES4_LANE1_QSGMII_LANE6 0x1 +#define J784S4_SERDES4_LANE1_IP3_UNUSED 0x2 +#define J784S4_SERDES4_LANE1_IP4_UNUSED 0x3 + +#define J784S4_SERDES4_LANE2_EDP_LANE2 0x0 +#define J784S4_SERDES4_LANE2_QSGMII_LANE7 0x1 +#define J784S4_SERDES4_LANE2_IP3_UNUSED 0x2 +#define J784S4_SERDES4_LANE2_IP4_UNUSED 0x3 + +#define J784S4_SERDES4_LANE3_EDP_LANE3 0x0 +#define J784S4_SERDES4_LANE3_QSGMII_LANE8 0x1 +#define J784S4_SERDES4_LANE3_USB 0x2 +#define J784S4_SERDES4_LANE3_IP4_UNUSED 0x3 + +#endif /* DTS_ARM64_TI_K3_SERDES_H */