[U-Boot] Unable to power the USB Keyboard on u-boot
Dear All,
I am trying to use "usb keyboard" on u-boot. I am using the u-boot stack which was shared by you. Can you help me to know where problem is going. I am sending some of debug prints which i found on my "Beagle board xM".
I have connected usb mouse and usb keyboard on same side of port, here usb mouse lights up but the keyboard does not powers on. Both keyboard and Mouse are from logitech.
Please help me to make this up as i have scheduled demo.
/***************** usb reset *************************************/
OMAP3 beagleboard.org # usb reset
(Re)start USB...
USB: Initializing OMAP EHCI OMAP
UHH_REVISION 0x10
OMAP EHCI init done
Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... New Device 0
New Device 1
New Device 2
New Device 3
New Device 4
5 USB Device(s) found
USB KBD: found set protocol...
USB KBD:
found set idle...
USB KBD: enable interrupt pipe...
USB KBD: found set up device.
USB KBD: register.
usb_kbd_dev.name- usbkbd
before stdio register
clone _dev->name-usbkbd,dev->name-usbkbd
clone _dev->flag- 80000003
in stdio register,usb_kbd_dev.name- usbkbd
After stdio register
before strcmp
stdin name- serial
After strcmp
stdin name- serial
before over write
before console assign
before error test
scan end
scanning bus for storage devices... 0 Storage Device(s) found
scanning bus for ethernet devices... Warning: failed to set MAC address
1 Ethernet Device(s) found
OMAP3 beagleboard.org # /*****************************************************/
/******************* coninfo **************************/
OMAP3 beagleboard.org # coninfo
List of available devices:
serial 80000003 SIO stdout stderr
usbtty 00000003 .IO
usbkbd 80000003 SIO stdin
OMAP3 beagleboard.org # ---------------------------------------------------------------> here i am able to switch the console using "setenv stdin usbkbd" but No power on keyboard does not help. /******************************************************/
/**************** usb info ***************************/
OMAP3 beagleboard.org# usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms
2: Hub, USB Revision 2.0
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0424 Product 0x9514 Version 2.0
Configuration: 1
- Interfaces: 1 Self Powered Remote Wakeup 2mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms
- Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms
3: Vendor specific, USB Revision 2.0
- Class: Vendor specific
- PacketSize: 64 Configurations: 1
- Vendor: 0x0424 Product 0xec00 Version 2.0
Configuration: 1
- Interfaces: 1 Self Powered Remote Wakeup 2mA
Interface: 0
- Alternate Setting 0, Endpoints: 3
- Class Vendor specific
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
- Endpoint 3 In Interrupt MaxPacket 16 Interval 4ms
4: Human Interface, USB Revision 1.10
- LITEON Technology USB Multimedia Keyboard
- Class: (from Interface) Human Interface
- PacketSize: 8 Configurations: 1
- Vendor: 0x046d Product 0xc312 Version 1.1
Configuration: 1
- Interfaces: 1 Bus Powered Remote Wakeup 70mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Human Interface, Subclass: Boot Keyboard
- Endpoint 1 In Interrupt MaxPacket 8 Interval 24ms
5: Human Interface, USB Revision 2.0
- Logitech USB Optical Mouse
- Class: (from Interface) Human Interface
- PacketSize: 8 Configurations: 1
- Vendor: 0x046d Product 0xc018 Version 67.1
Configuration: 1
- Interfaces: 1 Bus Powered Remote Wakeup 100mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Human Interface, Subclass: Boot Mouse
- Endpoint 1 In Interrupt MaxPacket 5 Interval 10ms
OMAP3 beagleboard.org # /****************************************************/
Thanks & Regards Atul Kumar
Dear Atul Kumar,
Dear All,
I am trying to use "usb keyboard" on u-boot. I am using theu-boot stack which was shared by you. Can you help me to know where problem is going. I am sending some of debug prints which i found on my "Beagle board xM".
I have connected usb mouse and usb keyboard on same side of port, here usb mouse lights up but the keyboard does not powers on. Both keyboard and Mouse are from logitech.
Please help me to make this up as i have scheduled demo.
[...]
What version of uboot is that? Try with latest u-boot git head, it should have the beagleboard/usb patches in there.
Best regards, Marek Vasut
On Friday 20 July 2012 07:10 PM, Marek Vasut wrote: Dear Marek, Thanks for your reply..
Dear Atul Kumar,
Dear All,
I am trying to use "usb keyboard" on u-boot. I am using theu-boot stack which was shared by you. Can you help me to know where problem is going. I am sending some of debug prints which i found on my "Beagle board xM".
I have connected usb mouse and usb keyboard on same side of port, here usb mouse lights up but the keyboard does not powers on. Both keyboard and Mouse are from logitech.
Please help me to make this up as i have scheduled demo.
[...]
What version of uboot is that? Try with latest u-boot git head, it should have the beagleboard/usb patches in there.
Best regards, Marek Vasut
I am using "u-boot version 2011-12" shared by Mr. Govind (ti) which was 1st updated by him.. I have also tried with the latest git: "u-boot-2012.07-rc1" but it is poping with "error : v7_dcache_inval_range - start address is not aligned". Do we have any solution for this. As i have also tried with Externally powered usb hub but it does not even initializes with it. Although i can see the device Name in u"usb tree". Any suggestion or solutions are always welcome.
Thanks & Regards Atul Kumar
Dear atulronu,
On Friday 20 July 2012 07:10 PM, Marek Vasut wrote: Dear Marek, Thanks for your reply..
Dear Atul Kumar,
Dear All,
I am trying to use "usb keyboard" on u-boot. I am using theu-boot stack which was shared by you. Can you help me to know where problem is going. I am sending some of debug prints which i found on my "Beagle board xM".
I have connected usb mouse and usb keyboard on same side of port, here usb
mouse lights up but the keyboard does not powers on. Both keyboard and Mouse are from logitech.
Please help me to make this up as i have scheduled demo.
[...]
What version of uboot is that? Try with latest u-boot git head, it should have the beagleboard/usb patches in there.
Best regards, Marek Vasut
I am using "u-boot version 2011-12" shared by Mr. Govind (ti) whichwas 1st updated by him.. I have also tried with the latest git: "u-boot-2012.07-rc1" but it is poping with "error : v7_dcache_inval_range - start address is not aligned". Do we have any solution for this.
Yes, latest git (-rc2 and soon to be released .07) has a fix for that. Tom?
As i have also tried with Externally powered usb hub but it does not even initializes with it. Although i can see the device Name in u"usb tree". Any suggestion or solutions are always welcome.
Thanks & Regards Atul Kumar
Best regards, Marek Vasut
On 07/24/2012 12:44 PM, Marek Vasut wrote:
Dear atulronu,
On Friday 20 July 2012 07:10 PM, Marek Vasut wrote: Dear Marek, Thanks for your reply..
Dear Atul Kumar,
Dear All,
I am trying to use "usb keyboard" on u-boot. I am using theu-boot stack which was shared by you. Can you help me to know where problem is going. I am sending some of debug prints which i found on my "Beagle board xM".
I have connected usb mouse and usb keyboard on same side of port, here usb
mouse lights up but the keyboard does not powers on. Both keyboard and Mouse are from logitech.
Please help me to make this up as i have scheduled demo.
[...]
What version of uboot is that? Try with latest u-boot git head, it should have the beagleboard/usb patches in there.
Best regards, Marek Vasut
I am using "u-boot version 2011-12" shared by Mr. Govind (ti) whichwas 1st updated by him.. I have also tried with the latest git: "u-boot-2012.07-rc1" but it is poping with "error : v7_dcache_inval_range - start address is not aligned". Do we have any solution for this.
Yes, latest git (-rc2 and soon to be released .07) has a fix for that. Tom?
I've gotten success reports from everyone I had that had found various breakage previously with the previous attempts.
participants (4)
-
Atul Kumar -
atulronu
-
Marek Vasut -
Tom Rini