[U-Boot] [PATCH v3 0/3] imx: mx6slevk add pmic support
This patch set is extracted from the previous "imx:mx6 add ldo bypass" patch set, with only one return value change.
patch 1/3 is add pad settings for I2C1 patch 2/3 is add I2C and PMIC support in board header file patch 3/3 is to add pmic support for mx6slevk.
patch 3/3 is from patch 3/12 in previous "imx:mx6 add ldo bypass" patch, with only one small change is return value.
Changes v3: Take Fabio's suggestion, for patch 3/3, remove ret variable, and directly "return pfuze_mode_init(xxx)"
Changes v2: Changing "return -EIO" to "return ret".
Peng Fan (3): imx:mx6sl add I2c pad settings imx:mx6slevk add pmic and i2c configuration imx:mx6slevk implement power init board
arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 5 ++++ board/freescale/mx6slevk/mx6slevk.c | 42 ++++++++++++++++++++++++++++++ include/configs/mx6slevk.h | 12 +++++++++ 3 files changed, 59 insertions(+)
A few pad settings are I2C1
Signed-off-by: Peng Fan Peng.Fan@freescale.com --- arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 5 +++++ 1 file changed, 5 insertions(+)
diff --git a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h index 9ded3d8..0475203 100644 --- a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h +++ b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h @@ -58,5 +58,10 @@ enum {
MX6_PAD_KEY_COL4__USB_USBOTG1_PWR = IOMUX_PAD(0x0484, 0x017C, 6, 0x0000, 0, 0), MX6_PAD_KEY_COL5__USB_USBOTG2_PWR = IOMUX_PAD(0x0488, 0x0180, 6, 0x0000, 0, 0), + + MX6_PAD_I2C1_SDA__I2C1_SDA = IOMUX_PAD(0x0450, 0x0160, 0x10, 0x0720, 2, 0), + MX6_PAD_I2C1_SDA__GPIO_3_13 = IOMUX_PAD(0x0450, 0x0160, 5, 0x0000, 0, 0), + MX6_PAD_I2C1_SCL__I2C1_SCL = IOMUX_PAD(0x044C, 0x015C, 0x10, 0x071C, 2, 0), + MX6_PAD_I2C1_SCL__GPIO_3_12 = IOMUX_PAD(0x044C, 0x015C, 5, 0x0000, 0, 0), }; #endif /* __ASM_ARCH_MX6_MX6SL_PINS_H__ */
On 12/02/2015 02:36, Peng Fan wrote:
A few pad settings are I2C1
Signed-off-by: Peng Fan Peng.Fan@freescale.com
Applied to u-boot-imx, thanks !
Best regards, Stefano Babic
Add pmic and i2c configuration in board header file.
Signed-off-by: Peng Fan Peng.Fan@freescale.com --- include/configs/mx6slevk.h | 12 ++++++++++++ 1 file changed, 12 insertions(+)
diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h index c567d9d..1221418 100644 --- a/include/configs/mx6slevk.h +++ b/include/configs/mx6slevk.h @@ -48,6 +48,18 @@ #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION
+/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_PFUZE100 +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 + #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_MII
On 12/02/2015 02:36, Peng Fan wrote:
Add pmic and i2c configuration in board header file.
Signed-off-by: Peng Fan Peng.Fan@freescale.com
Applied to u-boot-imx, thanks !
Best regards, Stefano Babic
Implement power_init_board and related I2C interface configuration.
After adding this, uboot can successfully detect and configure pmic.
" U-Boot 2015.01-00281-ge29eddf (Feb 12 2015 - 09:24:01)
CPU: Freescale i.MX6SL rev1.0 at 396 MHz Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 "
Signed-off-by: Peng Fan Peng.Fan@freescale.com --- board/freescale/mx6slevk/mx6slevk.c | 42 +++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+)
diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c index 838ea6c..c65f72b 100644 --- a/board/freescale/mx6slevk/mx6slevk.c +++ b/board/freescale/mx6slevk/mx6slevk.c @@ -13,13 +13,18 @@ #include <asm/arch/sys_proto.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> #include <asm/imx-common/spi.h> #include <asm/io.h> #include <linux/sizes.h> #include <common.h> #include <fsl_esdhc.h> +#include <i2c.h> #include <mmc.h> #include <netdev.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h> +#include "../common/pfuze.h" #include <usb.h> #include <usb/ehci-fsl.h>
@@ -40,6 +45,11 @@ DECLARE_GLOBAL_DATA_PTR; #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) + #define ETH_PHY_RESET IMX_GPIO_NR(4, 21)
int dram_init(void) @@ -221,6 +231,34 @@ int board_mmc_init(bd_t *bis) return 0; }
+#ifdef CONFIG_SYS_I2C_MXC +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +/* I2C1 for PMIC */ +struct i2c_pads_info i2c_pad_info1 = { + .sda = { + .i2c_mode = MX6_PAD_I2C1_SDA__I2C1_SDA | PC, + .gpio_mode = MX6_PAD_I2C1_SDA__GPIO_3_13 | PC, + .gp = IMX_GPIO_NR(3, 13), + }, + .scl = { + .i2c_mode = MX6_PAD_I2C1_SCL__I2C1_SCL | PC, + .gpio_mode = MX6_PAD_I2C1_SCL__GPIO_3_12 | PC, + .gp = IMX_GPIO_NR(3, 12), + }, +}; + +int power_init_board(void) +{ + struct pmic *p; + + p = pfuze_common_init(I2C_PMIC); + if (!p) + return -ENODEV; + + return pfuze_mode_init(p, APS_PFM); +} +#endif + #ifdef CONFIG_FEC_MXC int board_eth_init(bd_t *bis) { @@ -297,6 +335,10 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+#ifdef CONFIG_SYS_I2C_MXC + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); +#endif + #ifdef CONFIG_FEC_MXC setup_fec(); #endif
On 12/02/2015 02:36, Peng Fan wrote:
Implement power_init_board and related I2C interface configuration.
After adding this, uboot can successfully detect and configure pmic.
" U-Boot 2015.01-00281-ge29eddf (Feb 12 2015 - 09:24:01)
CPU: Freescale i.MX6SL rev1.0 at 396 MHz Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 "
Signed-off-by: Peng Fan Peng.Fan@freescale.com
Applied to u-boot-imx, thanks !
Best regards, Stefano Babic
Hi Peng,
On 12/02/2015 02:36, Peng Fan wrote:
This patch set is extracted from the previous "imx:mx6 add ldo bypass" patch set, with only one return value change.
patch 1/3 is add pad settings for I2C1 patch 2/3 is add I2C and PMIC support in board header file patch 3/3 is to add pmic support for mx6slevk.
patch 3/3 is from patch 3/12 in previous "imx:mx6 add ldo bypass" patch, with only one small change is return value.
Changes v3: Take Fabio's suggestion, for patch 3/3, remove ret variable, and directly "return pfuze_mode_init(xxx)"
Changes v2: Changing "return -EIO" to "return ret".
Peng Fan (3): imx:mx6sl add I2c pad settings imx:mx6slevk add pmic and i2c configuration imx:mx6slevk implement power init board
arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 5 ++++ board/freescale/mx6slevk/mx6slevk.c | 42 ++++++++++++++++++++++++++++++ include/configs/mx6slevk.h | 12 +++++++++ 3 files changed, 59 insertions(+)
They look good for me - if no comments will be posted, they will be merge by next iteration.
Best regards, Stefano Babic
participants (2)
-
Peng Fan -
Stefano Babic