From: Patrice Chotard patrice.chotard@st.com

All these files comes from kernel v4.15-rc1.

Update some header with correct STMicroelectronics Copyright.

Remove the paragraph about writing to the Free Software Foundation's mailing address as requested by checkpatch.

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- arch/arm/dts/Makefile | 2 + arch/arm/dts/stm32f4-pinctrl.dtsi | 344 ++++++++++++++ arch/arm/dts/stm32f429-disco.dts | 124 +++++ arch/arm/dts/stm32f429-pinctrl.dtsi | 96 ++++ arch/arm/dts/stm32f429.dtsi | 699 ++++++++++++++++++++++++++++ include/dt-bindings/mfd/stm32f4-rcc.h | 108 +++++ include/dt-bindings/pinctrl/stm32-pinfunc.h | 30 ++ 7 files changed, 1403 insertions(+) create mode 100644 arch/arm/dts/stm32f4-pinctrl.dtsi create mode 100644 arch/arm/dts/stm32f429-disco.dts create mode 100644 arch/arm/dts/stm32f429-pinctrl.dtsi create mode 100644 arch/arm/dts/stm32f429.dtsi create mode 100644 include/dt-bindings/mfd/stm32f4-rcc.h create mode 100644 include/dt-bindings/pinctrl/stm32-pinfunc.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 9db56f2..77fac9e 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -210,6 +210,8 @@ dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \

dtb-$(CONFIG_ARCH_SNAPDRAGON) += dragonboard410c.dtb

+dtb-$(CONFIG_STM32F4) += stm32f429-disco.dtb + dtb-$(CONFIG_STM32F7) += stm32f746-disco.dtb \ stm32f769-disco.dtb dtb-$(CONFIG_STM32H7) += stm32h743i-disco.dtb \ diff --git a/arch/arm/dts/stm32f4-pinctrl.dtsi b/arch/arm/dts/stm32f4-pinctrl.dtsi new file mode 100644 index 0000000..df59956 --- /dev/null +++ b/arch/arm/dts/stm32f4-pinctrl.dtsi @@ -0,0 +1,344 @@ +/* + * Copyright (C) 2017, STMicroelectronics - All Rights Reserved + * Author(s): Alexandre Torgue alexandre.torgue@st.com for STMicroelectronics. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/pinctrl/stm32-pinfunc.h> +#include <dt-bindings/mfd/stm32f4-rcc.h> + +/ { + soc { + pinctrl: pin-controller { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x40020000 0x3000>; + interrupt-parent = <&exti>; + st,syscfg = <&syscfg 0x8>; + pins-are-numbered; + + gpioa: gpio@40020000 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x0 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>; + st,bank-name = "GPIOA"; + }; + + gpiob: gpio@40020400 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x400 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOB)>; + st,bank-name = "GPIOB"; + }; + + gpioc: gpio@40020800 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x800 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOC)>; + st,bank-name = "GPIOC"; + }; + + gpiod: gpio@40020c00 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0xc00 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOD)>; + st,bank-name = "GPIOD"; + }; + + gpioe: gpio@40021000 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1000 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOE)>; + st,bank-name = "GPIOE"; + }; + + gpiof: gpio@40021400 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1400 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOF)>; + st,bank-name = "GPIOF"; + }; + + gpiog: gpio@40021800 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1800 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOG)>; + st,bank-name = "GPIOG"; + }; + + gpioh: gpio@40021c00 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1c00 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOH)>; + st,bank-name = "GPIOH"; + }; + + gpioi: gpio@40022000 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x2000 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOI)>; + st,bank-name = "GPIOI"; + }; + + gpioj: gpio@40022400 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x2400 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOJ)>; + st,bank-name = "GPIOJ"; + }; + + gpiok: gpio@40022800 { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x2800 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOK)>; + st,bank-name = "GPIOK"; + }; + + usart1_pins_a: usart1@0 { + pins1 { + pinmux = <STM32_PINMUX('A', 9, AF7)>; /* USART1_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('A', 10, AF7)>; /* USART1_RX */ + bias-disable; + }; + }; + + usart3_pins_a: usart3@0 { + pins1 { + pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 11, AF7)>; /* USART3_RX */ + bias-disable; + }; + }; + + usbotg_fs_pins_a: usbotg_fs@0 { + pins { + pinmux = <STM32_PINMUX('A', 10, AF10)>, /* OTG_FS_ID */ + <STM32_PINMUX('A', 11, AF10)>, /* OTG_FS_DM */ + <STM32_PINMUX('A', 12, AF10)>; /* OTG_FS_DP */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + }; + + usbotg_fs_pins_b: usbotg_fs@1 { + pins { + pinmux = <STM32_PINMUX('B', 12, AF12)>, /* OTG_HS_ID */ + <STM32_PINMUX('B', 14, AF12)>, /* OTG_HS_DM */ + <STM32_PINMUX('B', 15, AF12)>; /* OTG_HS_DP */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + }; + + usbotg_hs_pins_a: usbotg_hs@0 { + pins { + pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT*/ + <STM32_PINMUX('I', 11, AF10)>, /* OTG_HS_ULPI_DIR */ + <STM32_PINMUX('C', 0, AF10)>, /* OTG_HS_ULPI_STP */ + <STM32_PINMUX('A', 5, AF10)>, /* OTG_HS_ULPI_CK */ + <STM32_PINMUX('A', 3, AF10)>, /* OTG_HS_ULPI_D0 */ + <STM32_PINMUX('B', 0, AF10)>, /* OTG_HS_ULPI_D1 */ + <STM32_PINMUX('B', 1, AF10)>, /* OTG_HS_ULPI_D2 */ + <STM32_PINMUX('B', 10, AF10)>, /* OTG_HS_ULPI_D3 */ + <STM32_PINMUX('B', 11, AF10)>, /* OTG_HS_ULPI_D4 */ + <STM32_PINMUX('B', 12, AF10)>, /* OTG_HS_ULPI_D5 */ + <STM32_PINMUX('B', 13, AF10)>, /* OTG_HS_ULPI_D6 */ + <STM32_PINMUX('B', 5, AF10)>; /* OTG_HS_ULPI_D7 */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + }; + + ethernet_mii: mii@0 { + pins { + pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH_MII_TXD0_ETH_RMII_TXD0 */ + <STM32_PINMUX('G', 14, AF11)>, /* ETH_MII_TXD1_ETH_RMII_TXD1 */ + <STM32_PINMUX('C', 2, AF11)>, /* ETH_MII_TXD2 */ + <STM32_PINMUX('B', 8, AF11)>, /* ETH_MII_TXD3 */ + <STM32_PINMUX('C', 3, AF11)>, /* ETH_MII_TX_CLK */ + <STM32_PINMUX('G', 11,AF11)>, /* ETH_MII_TX_EN_ETH_RMII_TX_EN */ + <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */ + <STM32_PINMUX('C', 1, AF11)>, /* ETH_MDC */ + <STM32_PINMUX('A', 1, AF11)>, /* ETH_MII_RX_CLK_ETH_RMII_REF_CLK */ + <STM32_PINMUX('A', 7, AF11)>, /* ETH_MII_RX_DV_ETH_RMII_CRS_DV */ + <STM32_PINMUX('C', 4, AF11)>, /* ETH_MII_RXD0_ETH_RMII_RXD0 */ + <STM32_PINMUX('C', 5, AF11)>, /* ETH_MII_RXD1_ETH_RMII_RXD1 */ + <STM32_PINMUX('H', 6, AF11)>, /* ETH_MII_RXD2 */ + <STM32_PINMUX('H', 7, AF11)>; /* ETH_MII_RXD3 */ + slew-rate = <2>; + }; + }; + + adc3_in8_pin: adc@200 { + pins { + pinmux = <STM32_PINMUX('F', 10, ANALOG)>; + }; + }; + + pwm1_pins: pwm@1 { + pins { + pinmux = <STM32_PINMUX('A', 8, AF1)>, /* TIM1_CH1 */ + <STM32_PINMUX('B', 13, AF1)>, /* TIM1_CH1N */ + <STM32_PINMUX('B', 12, AF1)>; /* TIM1_BKIN */ + }; + }; + + pwm3_pins: pwm@3 { + pins { + pinmux = <STM32_PINMUX('B', 4, AF2)>, /* TIM3_CH1 */ + <STM32_PINMUX('B', 5, AF2)>; /* TIM3_CH2 */ + }; + }; + + i2c1_pins: i2c1@0 { + pins { + pinmux = <STM32_PINMUX('B', 9, AF4)>, /* I2C1_SDA */ + <STM32_PINMUX('B', 6, AF4)>; /* I2C1_SCL */ + bias-disable; + drive-open-drain; + slew-rate = <3>; + }; + }; + + ltdc_pins: ltdc@0 { + pins { + pinmux = <STM32_PINMUX('I', 12, AF14)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 13, AF14)>, /* LCD_VSYNC */ + <STM32_PINMUX('I', 14, AF14)>, /* LCD_CLK */ + <STM32_PINMUX('I', 15, AF14)>, /* LCD_R0 */ + <STM32_PINMUX('J', 0, AF14)>, /* LCD_R1 */ + <STM32_PINMUX('J', 1, AF14)>, /* LCD_R2 */ + <STM32_PINMUX('J', 2, AF14)>, /* LCD_R3 */ + <STM32_PINMUX('J', 3, AF14)>, /* LCD_R4 */ + <STM32_PINMUX('J', 4, AF14)>, /* LCD_R5 */ + <STM32_PINMUX('J', 5, AF14)>, /* LCD_R6*/ + <STM32_PINMUX('J', 6, AF14)>, /* LCD_R7 */ + <STM32_PINMUX('J', 7, AF14)>, /* LCD_G0 */ + <STM32_PINMUX('J', 8, AF14)>, /* LCD_G1 */ + <STM32_PINMUX('J', 9, AF14)>, /* LCD_G2 */ + <STM32_PINMUX('J', 10, AF14)>, /* LCD_G3 */ + <STM32_PINMUX('J', 11, AF14)>, /* LCD_G4 */ + <STM32_PINMUX('J', 12, AF14)>, /* LCD_B0 */ + <STM32_PINMUX('J', 13, AF14)>, /* LCD_B1 */ + <STM32_PINMUX('J', 14, AF14)>, /* LCD_B2 */ + <STM32_PINMUX('J', 15, AF14)>, /* LCD_B3*/ + <STM32_PINMUX('K', 0, AF14)>, /* LCD_G5 */ + <STM32_PINMUX('K', 1, AF14)>, /* LCD_G6 */ + <STM32_PINMUX('K', 2, AF14)>, /* LCD_G7 */ + <STM32_PINMUX('K', 3, AF14)>, /* LCD_B4 */ + <STM32_PINMUX('K', 4, AF14)>, /* LCD_B5 */ + <STM32_PINMUX('K', 5, AF14)>, /* LCD_B6 */ + <STM32_PINMUX('K', 6, AF14)>, /* LCD_B7 */ + <STM32_PINMUX('K', 7, AF14)>; /* LCD_DE */ + slew-rate = <2>; + }; + }; + + dcmi_pins: dcmi@0 { + pins { + pinmux = <STM32_PINMUX('A', 4, AF13)>, /* DCMI_HSYNC */ + <STM32_PINMUX('B', 7, AF13)>, /* DCMI_VSYNC */ + <STM32_PINMUX('A', 6, AF13)>, /* DCMI_PIXCLK */ + <STM32_PINMUX('C', 6, AF13)>, /* DCMI_D0 */ + <STM32_PINMUX('C', 7, AF13)>, /* DCMI_D1 */ + <STM32_PINMUX('C', 8, AF13)>, /* DCMI_D2 */ + <STM32_PINMUX('C', 9, AF13)>, /* DCMI_D3 */ + <STM32_PINMUX('C', 11, AF13)>, /*DCMI_D4 */ + <STM32_PINMUX('D', 3, AF13)>, /* DCMI_D5 */ + <STM32_PINMUX('B', 8, AF13)>, /* DCMI_D6 */ + <STM32_PINMUX('E', 6, AF13)>, /* DCMI_D7 */ + <STM32_PINMUX('C', 10, AF13)>, /* DCMI_D8 */ + <STM32_PINMUX('C', 12, AF13)>, /* DCMI_D9 */ + <STM32_PINMUX('D', 6, AF13)>, /* DCMI_D10 */ + <STM32_PINMUX('D', 2, AF13)>; /* DCMI_D11 */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + }; + }; + }; +}; diff --git a/arch/arm/dts/stm32f429-disco.dts b/arch/arm/dts/stm32f429-disco.dts new file mode 100644 index 0000000..e914b6b --- /dev/null +++ b/arch/arm/dts/stm32f429-disco.dts @@ -0,0 +1,124 @@ +/* + * Copyright (C) 2015, STMicroelectronics - All Rights Reserved + * Author(s): Maxime Coquelin mcoquelin.stm32@gmail.com for STMicroelectronics. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "stm32f429.dtsi" +#include "stm32f429-pinctrl.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "STMicroelectronics STM32F429i-DISCO board"; + compatible = "st,stm32f429i-disco", "st,stm32f429"; + + chosen { + bootargs = "root=/dev/ram"; + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x90000000 0x800000>; + }; + + aliases { + serial0 = &usart1; + }; + + leds { + compatible = "gpio-leds"; + red { + gpios = <&gpiog 14 0>; + }; + green { + gpios = <&gpiog 13 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + button@0 { + label = "User"; + linux,code = <KEY_HOME>; + gpios = <&gpioa 0 0>; + }; + }; + + /* This turns on vbus for otg for host mode (dwc2) */ + vcc5v_otg: vcc5v-otg-regulator { + compatible = "regulator-fixed"; + gpio = <&gpioc 4 0>; + regulator-name = "vcc5_host1"; + regulator-always-on; + }; +}; + +&clk_hse { + clock-frequency = <8000000>; +}; + +&crc { + status = "okay"; +}; + +&rtc { + assigned-clocks = <&rcc 1 CLK_RTC>; + assigned-clock-parents = <&rcc 1 CLK_LSI>; + status = "okay"; +}; + +&usart1 { + pinctrl-0 = <&usart1_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbotg_hs { + compatible = "st,stm32f4x9-fsotg"; + dr_mode = "host"; + pinctrl-0 = <&usbotg_fs_pins_b>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/arch/arm/dts/stm32f429-pinctrl.dtsi b/arch/arm/dts/stm32f429-pinctrl.dtsi new file mode 100644 index 0000000..77246b3 --- /dev/null +++ b/arch/arm/dts/stm32f429-pinctrl.dtsi @@ -0,0 +1,96 @@ +/* + * Copyright (C) 2017, STMicroelectronics - All Rights Reserved + * Author(s): Alexandre Torgue alexandre.torgue@st.com for STMicroelectronics. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "stm32f4-pinctrl.dtsi" + +/ { + soc { + pinctrl: pin-controller { + compatible = "st,stm32f429-pinctrl"; + + gpioa: gpio@40020000 { + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpiob: gpio@40020400 { + gpio-ranges = <&pinctrl 0 16 16>; + }; + + gpioc: gpio@40020800 { + gpio-ranges = <&pinctrl 0 32 16>; + }; + + gpiod: gpio@40020c00 { + gpio-ranges = <&pinctrl 0 48 16>; + }; + + gpioe: gpio@40021000 { + gpio-ranges = <&pinctrl 0 64 16>; + }; + + gpiof: gpio@40021400 { + gpio-ranges = <&pinctrl 0 80 16>; + }; + + gpiog: gpio@40021800 { + gpio-ranges = <&pinctrl 0 96 16>; + }; + + gpioh: gpio@40021c00 { + gpio-ranges = <&pinctrl 0 112 16>; + }; + + gpioi: gpio@40022000 { + gpio-ranges = <&pinctrl 0 128 16>; + }; + + gpioj: gpio@40022400 { + gpio-ranges = <&pinctrl 0 144 16>; + }; + + gpiok: gpio@40022800 { + gpio-ranges = <&pinctrl 0 160 8>; + }; + }; + }; +}; diff --git a/arch/arm/dts/stm32f429.dtsi b/arch/arm/dts/stm32f429.dtsi new file mode 100644 index 0000000..23b7946 --- /dev/null +++ b/arch/arm/dts/stm32f429.dtsi @@ -0,0 +1,699 @@ +/* + * Copyright (C) 2015, STMicroelectronics - All Rights Reserved + * Author(s): Maxime Coquelin mcoquelin.stm32@gmail.com for STMicroelectronics. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "skeleton.dtsi" +#include "armv7-m.dtsi" +#include <dt-bindings/clock/stm32fx-clock.h> +#include <dt-bindings/mfd/stm32f4-rcc.h> + +/ { + clocks { + clk_hse: clk-hse { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + }; + + clk_lse: clk-lse { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + }; + + clk_lsi: clk-lsi { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32000>; + }; + + clk_i2s_ckin: i2s-ckin { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + }; + }; + + soc { + timer2: timer@40000000 { + compatible = "st,stm32-timer"; + reg = <0x40000000 0x400>; + interrupts = <28>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM2)>; + status = "disabled"; + }; + + timers2: timers@40000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000000 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM2)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@1 { + compatible = "st,stm32-timer-trigger"; + reg = <1>; + status = "disabled"; + }; + }; + + timer3: timer@40000400 { + compatible = "st,stm32-timer"; + reg = <0x40000400 0x400>; + interrupts = <29>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM3)>; + status = "disabled"; + }; + + timers3: timers@40000400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000400 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM3)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@2 { + compatible = "st,stm32-timer-trigger"; + reg = <2>; + status = "disabled"; + }; + }; + + timer4: timer@40000800 { + compatible = "st,stm32-timer"; + reg = <0x40000800 0x400>; + interrupts = <30>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM4)>; + status = "disabled"; + }; + + timers4: timers@40000800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000800 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM4)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@3 { + compatible = "st,stm32-timer-trigger"; + reg = <3>; + status = "disabled"; + }; + }; + + timer5: timer@40000c00 { + compatible = "st,stm32-timer"; + reg = <0x40000c00 0x400>; + interrupts = <50>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM5)>; + }; + + timers5: timers@40000c00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000C00 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM5)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@4 { + compatible = "st,stm32-timer-trigger"; + reg = <4>; + status = "disabled"; + }; + }; + + timer6: timer@40001000 { + compatible = "st,stm32-timer"; + reg = <0x40001000 0x400>; + interrupts = <54>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM6)>; + status = "disabled"; + }; + + timers6: timers@40001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001000 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM6)>; + clock-names = "int"; + status = "disabled"; + + timer@5 { + compatible = "st,stm32-timer-trigger"; + reg = <5>; + status = "disabled"; + }; + }; + + timer7: timer@40001400 { + compatible = "st,stm32-timer"; + reg = <0x40001400 0x400>; + interrupts = <55>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM7)>; + status = "disabled"; + }; + + timers7: timers@40001400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001400 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM7)>; + clock-names = "int"; + status = "disabled"; + + timer@6 { + compatible = "st,stm32-timer-trigger"; + reg = <6>; + status = "disabled"; + }; + }; + + timers12: timers@40001800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001800 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM12)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@11 { + compatible = "st,stm32-timer-trigger"; + reg = <11>; + status = "disabled"; + }; + }; + + timers13: timers@40001c00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001C00 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM13)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + timers14: timers@40002000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40002000 0x400>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM14)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + rtc: rtc@40002800 { + compatible = "st,stm32-rtc"; + reg = <0x40002800 0x400>; + clocks = <&rcc 1 CLK_RTC>; + clock-names = "ck_rtc"; + assigned-clocks = <&rcc 1 CLK_RTC>; + assigned-clock-parents = <&rcc 1 CLK_LSE>; + interrupt-parent = <&exti>; + interrupts = <17 1>; + interrupt-names = "alarm"; + st,syscfg = <&pwrcfg>; + status = "disabled"; + }; + + iwdg: watchdog@40003000 { + compatible = "st,stm32-iwdg"; + reg = <0x40003000 0x400>; + clocks = <&clk_lsi>; + status = "disabled"; + }; + + usart2: serial@40004400 { + compatible = "st,stm32-uart"; + reg = <0x40004400 0x400>; + interrupts = <38>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART2)>; + status = "disabled"; + }; + + usart3: serial@40004800 { + compatible = "st,stm32-uart"; + reg = <0x40004800 0x400>; + interrupts = <39>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART3)>; + status = "disabled"; + dmas = <&dma1 1 4 0x400 0x0>, + <&dma1 3 4 0x400 0x0>; + dma-names = "rx", "tx"; + }; + + usart4: serial@40004c00 { + compatible = "st,stm32-uart"; + reg = <0x40004c00 0x400>; + interrupts = <52>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART4)>; + status = "disabled"; + }; + + usart5: serial@40005000 { + compatible = "st,stm32-uart"; + reg = <0x40005000 0x400>; + interrupts = <53>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART5)>; + status = "disabled"; + }; + + i2c1: i2c@40005400 { + compatible = "st,stm32f4-i2c"; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc STM32F4_APB1_RESET(I2C1)>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(I2C1)>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + dac: dac@40007400 { + compatible = "st,stm32f4-dac-core"; + reg = <0x40007400 0x400>; + resets = <&rcc STM32F4_APB1_RESET(DAC)>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(DAC)>; + clock-names = "pclk"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + dac1: dac@1 { + compatible = "st,stm32-dac"; + #io-channels-cells = <1>; + reg = <1>; + status = "disabled"; + }; + + dac2: dac@2 { + compatible = "st,stm32-dac"; + #io-channels-cells = <1>; + reg = <2>; + status = "disabled"; + }; + }; + + usart7: serial@40007800 { + compatible = "st,stm32-uart"; + reg = <0x40007800 0x400>; + interrupts = <82>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART7)>; + status = "disabled"; + }; + + usart8: serial@40007c00 { + compatible = "st,stm32-uart"; + reg = <0x40007c00 0x400>; + interrupts = <83>; + clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART8)>; + status = "disabled"; + }; + + timers1: timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM1)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@0 { + compatible = "st,stm32-timer-trigger"; + reg = <0>; + status = "disabled"; + }; + }; + + timers8: timers@40010400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010400 0x400>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM8)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@7 { + compatible = "st,stm32-timer-trigger"; + reg = <7>; + status = "disabled"; + }; + }; + + usart1: serial@40011000 { + compatible = "st,stm32-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(USART1)>; + status = "disabled"; + dmas = <&dma2 2 4 0x400 0x0>, + <&dma2 7 4 0x400 0x0>; + dma-names = "rx", "tx"; + }; + + usart6: serial@40011400 { + compatible = "st,stm32-uart"; + reg = <0x40011400 0x400>; + interrupts = <71>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(USART6)>; + status = "disabled"; + }; + + adc: adc@40012000 { + compatible = "st,stm32f4-adc-core"; + reg = <0x40012000 0x400>; + interrupts = <18>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC1)>; + clock-names = "adc"; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + adc1: adc@0 { + compatible = "st,stm32f4-adc"; + #io-channel-cells = <1>; + reg = <0x0>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC1)>; + interrupt-parent = <&adc>; + interrupts = <0>; + dmas = <&dma2 0 0 0x400 0x0>; + dma-names = "rx"; + status = "disabled"; + }; + + adc2: adc@100 { + compatible = "st,stm32f4-adc"; + #io-channel-cells = <1>; + reg = <0x100>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC2)>; + interrupt-parent = <&adc>; + interrupts = <1>; + dmas = <&dma2 3 1 0x400 0x0>; + dma-names = "rx"; + status = "disabled"; + }; + + adc3: adc@200 { + compatible = "st,stm32f4-adc"; + #io-channel-cells = <1>; + reg = <0x200>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC3)>; + interrupt-parent = <&adc>; + interrupts = <2>; + dmas = <&dma2 1 2 0x400 0x0>; + dma-names = "rx"; + status = "disabled"; + }; + }; + + syscfg: system-config@40013800 { + compatible = "syscon"; + reg = <0x40013800 0x400>; + }; + + exti: interrupt-controller@40013c00 { + compatible = "st,stm32-exti"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x40013C00 0x400>; + interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <42>, <62>, <76>; + }; + + timers9: timers@40014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014000 0x400>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM9)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + + timer@8 { + compatible = "st,stm32-timer-trigger"; + reg = <8>; + status = "disabled"; + }; + }; + + timers10: timers@40014400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014400 0x400>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM10)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + timers11: timers@40014800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40014800 0x400>; + clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM11)>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + status = "disabled"; + }; + }; + + pwrcfg: power-config@40007000 { + compatible = "syscon"; + reg = <0x40007000 0x400>; + }; + + ltdc: display-controller@40016800 { + compatible = "st,stm32-ltdc"; + reg = <0x40016800 0x200>; + interrupts = <88>, <89>; + resets = <&rcc STM32F4_APB2_RESET(LTDC)>; + clocks = <&rcc 1 CLK_LCD>; + clock-names = "lcd"; + status = "disabled"; + }; + + crc: crc@40023000 { + compatible = "st,stm32f4-crc"; + reg = <0x40023000 0x400>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(CRC)>; + status = "disabled"; + }; + + rcc: rcc@40023810 { + #reset-cells = <1>; + #clock-cells = <2>; + compatible = "st,stm32f42xx-rcc", "st,stm32-rcc"; + reg = <0x40023800 0x400>; + clocks = <&clk_hse>, <&clk_i2s_ckin>; + st,syscfg = <&pwrcfg>; + assigned-clocks = <&rcc 1 CLK_HSE_RTC>; + assigned-clock-rates = <1000000>; + }; + + dma1: dma-controller@40026000 { + compatible = "st,stm32-dma"; + reg = <0x40026000 0x400>; + interrupts = <11>, + <12>, + <13>, + <14>, + <15>, + <16>, + <17>, + <47>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA1)>; + #dma-cells = <4>; + }; + + dma2: dma-controller@40026400 { + compatible = "st,stm32-dma"; + reg = <0x40026400 0x400>; + interrupts = <56>, + <57>, + <58>, + <59>, + <60>, + <68>, + <69>, + <70>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA2)>; + #dma-cells = <4>; + st,mem2mem; + }; + + mac: ethernet@40028000 { + compatible = "st,stm32-dwmac", "snps,dwmac-3.50a"; + reg = <0x40028000 0x8000>; + reg-names = "stmmaceth"; + interrupts = <61>; + interrupt-names = "macirq"; + clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx"; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(ETHMAC)>, + <&rcc 0 STM32F4_AHB1_CLOCK(ETHMACTX)>, + <&rcc 0 STM32F4_AHB1_CLOCK(ETHMACRX)>; + st,syscon = <&syscfg 0x4>; + snps,pbl = <8>; + snps,mixed-burst; + status = "disabled"; + }; + + usbotg_hs: usb@40040000 { + compatible = "snps,dwc2"; + reg = <0x40040000 0x40000>; + interrupts = <77>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(OTGHS)>; + clock-names = "otg"; + status = "disabled"; + }; + + usbotg_fs: usb@50000000 { + compatible = "st,stm32f4x9-fsotg"; + reg = <0x50000000 0x40000>; + interrupts = <67>; + clocks = <&rcc 0 39>; + clock-names = "otg"; + status = "disabled"; + }; + + dcmi: dcmi@50050000 { + compatible = "st,stm32-dcmi"; + reg = <0x50050000 0x400>; + interrupts = <78>; + resets = <&rcc STM32F4_AHB2_RESET(DCMI)>; + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>; + clock-names = "mclk"; + pinctrl-names = "default"; + pinctrl-0 = <&dcmi_pins>; + dmas = <&dma2 1 1 0x414 0x3>; + dma-names = "tx"; + status = "disabled"; + }; + + rng: rng@50060800 { + compatible = "st,stm32-rng"; + reg = <0x50060800 0x400>; + interrupts = <80>; + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(RNG)>; + + }; + }; +}; + +&systick { + clocks = <&rcc 1 SYSTICK>; + status = "okay"; +}; diff --git a/include/dt-bindings/mfd/stm32f4-rcc.h b/include/dt-bindings/mfd/stm32f4-rcc.h new file mode 100644 index 0000000..36448a5 --- /dev/null +++ b/include/dt-bindings/mfd/stm32f4-rcc.h @@ -0,0 +1,108 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * This header provides constants for the STM32F4 RCC IP + */ + +#ifndef _DT_BINDINGS_MFD_STM32F4_RCC_H +#define _DT_BINDINGS_MFD_STM32F4_RCC_H + +/* AHB1 */ +#define STM32F4_RCC_AHB1_GPIOA 0 +#define STM32F4_RCC_AHB1_GPIOB 1 +#define STM32F4_RCC_AHB1_GPIOC 2 +#define STM32F4_RCC_AHB1_GPIOD 3 +#define STM32F4_RCC_AHB1_GPIOE 4 +#define STM32F4_RCC_AHB1_GPIOF 5 +#define STM32F4_RCC_AHB1_GPIOG 6 +#define STM32F4_RCC_AHB1_GPIOH 7 +#define STM32F4_RCC_AHB1_GPIOI 8 +#define STM32F4_RCC_AHB1_GPIOJ 9 +#define STM32F4_RCC_AHB1_GPIOK 10 +#define STM32F4_RCC_AHB1_CRC 12 +#define STM32F4_RCC_AHB1_BKPSRAM 18 +#define STM32F4_RCC_AHB1_CCMDATARAM 20 +#define STM32F4_RCC_AHB1_DMA1 21 +#define STM32F4_RCC_AHB1_DMA2 22 +#define STM32F4_RCC_AHB1_DMA2D 23 +#define STM32F4_RCC_AHB1_ETHMAC 25 +#define STM32F4_RCC_AHB1_ETHMACTX 26 +#define STM32F4_RCC_AHB1_ETHMACRX 27 +#define STM32F4_RCC_AHB1_ETHMACPTP 28 +#define STM32F4_RCC_AHB1_OTGHS 29 +#define STM32F4_RCC_AHB1_OTGHSULPI 30 + +#define STM32F4_AHB1_RESET(bit) (STM32F4_RCC_AHB1_##bit + (0x10 * 8)) +#define STM32F4_AHB1_CLOCK(bit) (STM32F4_RCC_AHB1_##bit) + +/* AHB2 */ +#define STM32F4_RCC_AHB2_DCMI 0 +#define STM32F4_RCC_AHB2_CRYP 4 +#define STM32F4_RCC_AHB2_HASH 5 +#define STM32F4_RCC_AHB2_RNG 6 +#define STM32F4_RCC_AHB2_OTGFS 7 + +#define STM32F4_AHB2_RESET(bit) (STM32F4_RCC_AHB2_##bit + (0x14 * 8)) +#define STM32F4_AHB2_CLOCK(bit) (STM32F4_RCC_AHB2_##bit + 0x20) + +/* AHB3 */ +#define STM32F4_RCC_AHB3_FMC 0 +#define STM32F4_RCC_AHB3_QSPI 1 + +#define STM32F4_AHB3_RESET(bit) (STM32F4_RCC_AHB3_##bit + (0x18 * 8)) +#define STM32F4_AHB3_CLOCK(bit) (STM32F4_RCC_AHB3_##bit + 0x40) + +/* APB1 */ +#define STM32F4_RCC_APB1_TIM2 0 +#define STM32F4_RCC_APB1_TIM3 1 +#define STM32F4_RCC_APB1_TIM4 2 +#define STM32F4_RCC_APB1_TIM5 3 +#define STM32F4_RCC_APB1_TIM6 4 +#define STM32F4_RCC_APB1_TIM7 5 +#define STM32F4_RCC_APB1_TIM12 6 +#define STM32F4_RCC_APB1_TIM13 7 +#define STM32F4_RCC_APB1_TIM14 8 +#define STM32F4_RCC_APB1_WWDG 11 +#define STM32F4_RCC_APB1_SPI2 14 +#define STM32F4_RCC_APB1_SPI3 15 +#define STM32F4_RCC_APB1_UART2 17 +#define STM32F4_RCC_APB1_UART3 18 +#define STM32F4_RCC_APB1_UART4 19 +#define STM32F4_RCC_APB1_UART5 20 +#define STM32F4_RCC_APB1_I2C1 21 +#define STM32F4_RCC_APB1_I2C2 22 +#define STM32F4_RCC_APB1_I2C3 23 +#define STM32F4_RCC_APB1_CAN1 25 +#define STM32F4_RCC_APB1_CAN2 26 +#define STM32F4_RCC_APB1_PWR 28 +#define STM32F4_RCC_APB1_DAC 29 +#define STM32F4_RCC_APB1_UART7 30 +#define STM32F4_RCC_APB1_UART8 31 + +#define STM32F4_APB1_RESET(bit) (STM32F4_RCC_APB1_##bit + (0x20 * 8)) +#define STM32F4_APB1_CLOCK(bit) (STM32F4_RCC_APB1_##bit + 0x80) + +/* APB2 */ +#define STM32F4_RCC_APB2_TIM1 0 +#define STM32F4_RCC_APB2_TIM8 1 +#define STM32F4_RCC_APB2_USART1 4 +#define STM32F4_RCC_APB2_USART6 5 +#define STM32F4_RCC_APB2_ADC1 8 +#define STM32F4_RCC_APB2_ADC2 9 +#define STM32F4_RCC_APB2_ADC3 10 +#define STM32F4_RCC_APB2_SDIO 11 +#define STM32F4_RCC_APB2_SPI1 12 +#define STM32F4_RCC_APB2_SPI4 13 +#define STM32F4_RCC_APB2_SYSCFG 14 +#define STM32F4_RCC_APB2_TIM9 16 +#define STM32F4_RCC_APB2_TIM10 17 +#define STM32F4_RCC_APB2_TIM11 18 +#define STM32F4_RCC_APB2_SPI5 20 +#define STM32F4_RCC_APB2_SPI6 21 +#define STM32F4_RCC_APB2_SAI1 22 +#define STM32F4_RCC_APB2_LTDC 26 +#define STM32F4_RCC_APB2_DSI 27 + +#define STM32F4_APB2_RESET(bit) (STM32F4_RCC_APB2_##bit + (0x24 * 8)) +#define STM32F4_APB2_CLOCK(bit) (STM32F4_RCC_APB2_##bit + 0xA0) + +#endif /* _DT_BINDINGS_MFD_STM32F4_RCC_H */ diff --git a/include/dt-bindings/pinctrl/stm32-pinfunc.h b/include/dt-bindings/pinctrl/stm32-pinfunc.h new file mode 100644 index 0000000..b8dfe31 --- /dev/null +++ b/include/dt-bindings/pinctrl/stm32-pinfunc.h @@ -0,0 +1,30 @@ +#ifndef _DT_BINDINGS_STM32_PINFUNC_H +#define _DT_BINDINGS_STM32_PINFUNC_H + +/* define PIN modes */ +#define GPIO 0x0 +#define AF0 0x1 +#define AF1 0x2 +#define AF2 0x3 +#define AF3 0x4 +#define AF4 0x5 +#define AF5 0x6 +#define AF6 0x7 +#define AF7 0x8 +#define AF8 0x9 +#define AF9 0xa +#define AF10 0xb +#define AF11 0xc +#define AF12 0xd +#define AF13 0xe +#define AF14 0xf +#define AF15 0x10 +#define ANALOG 0x11 + +/* define Pins number*/ +#define PIN_NO(port, line) (((port) - 'A') * 0x10 + (line)) + +#define STM32_PINMUX(port, line, mode) (((PIN_NO(port, line)) << 8) | (mode)) + +#endif /* _DT_BINDINGS_STM32_PINFUNC_H */ +

From: Patrice Chotard patrice.chotard@st.com

Use available DM stm32_sdram.c driver instead of board SDRAM initialization. For that, enable OF_CONTROL, OF_EMBED and STM32_SDRAM flags.

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- board/st/stm32f429-discovery/stm32f429-discovery.c | 136 +++------------------ configs/stm32f429-discovery_defconfig | 6 +- include/configs/stm32f429-discovery.h | 1 - 3 files changed, 19 insertions(+), 124 deletions(-)

diff --git a/board/st/stm32f429-discovery/stm32f429-discovery.c b/board/st/stm32f429-discovery/stm32f429-discovery.c index 1c34a8e..7e8df8e 100644 --- a/board/st/stm32f429-discovery/stm32f429-discovery.c +++ b/board/st/stm32f429-discovery/stm32f429-discovery.c @@ -15,10 +15,8 @@ #include <dm.h> #include <stm32_rcc.h> #include <asm/io.h> -#include <asm/armv7m.h> #include <asm/arch/stm32.h> #include <asm/arch/gpio.h> -#include <asm/arch/fmc.h> #include <dm/platform_data/serial_stm32.h> #include <asm/arch/stm32_periph.h> #include <asm/arch/stm32_defs.h> @@ -140,56 +138,10 @@ out: */ #define STM32_RCC_ENR_FMC (1 << 0) /* FMC module clock */

-static inline u32 _ns2clk(u32 ns, u32 freq) -{ - u32 tmp = freq/1000000; - return (tmp * ns) / 1000; -} - -#define NS2CLK(ns) (_ns2clk(ns, freq)) - -/* - * Following are timings for IS42S16400J, from corresponding datasheet - */ -#define SDRAM_CAS 3 /* 3 cycles */ -#define SDRAM_NB 1 /* Number of banks */ -#define SDRAM_MWID 1 /* 16 bit memory */ - -#define SDRAM_NR 0x1 /* 12-bit row */ -#define SDRAM_NC 0x0 /* 8-bit col */ -#define SDRAM_RBURST 0x1 /* Single read requests always as bursts */ -#define SDRAM_RPIPE 0x0 /* No HCLK clock cycle delay */ - -#define SDRAM_TRRD (NS2CLK(14) - 1) -#define SDRAM_TRCD (NS2CLK(15) - 1) -#define SDRAM_TRP (NS2CLK(15) - 1) -#define SDRAM_TRAS (NS2CLK(42) - 1) -#define SDRAM_TRC (NS2CLK(63) - 1) -#define SDRAM_TRFC (NS2CLK(63) - 1) -#define SDRAM_TCDL (1 - 1) -#define SDRAM_TRDL (2 - 1) -#define SDRAM_TBDL (1 - 1) -#define SDRAM_TREF 1386 -#define SDRAM_TCCD (1 - 1) - -#define SDRAM_TXSR (NS2CLK(70) - 1)/* Row cycle time after precharge */ -#define SDRAM_TMRD (3 - 1) /* Page 10, Mode Register Set */ - -/* Last data-in to row precharge, need also comply ineq from RM 37.7.5 */ -#define SDRAM_TWR max(\ - (int)max((int)SDRAM_TRDL, (int)(SDRAM_TRAS - SDRAM_TRCD - 1)), \ - (int)(SDRAM_TRC - SDRAM_TRCD - SDRAM_TRP - 2)\ -) - -#define SDRAM_MODE_BL_SHIFT 0 -#define SDRAM_MODE_CAS_SHIFT 4 -#define SDRAM_MODE_BL 0 -#define SDRAM_MODE_CAS SDRAM_CAS - int dram_init(void) { - u32 freq; int rv; + struct udevice *dev;

rv = fmc_setup_gpio(); if (rv) @@ -197,83 +149,23 @@ int dram_init(void)

setbits_le32(&STM32_RCC->ahb3enr, STM32_RCC_ENR_FMC);

- /* - * Get frequency for NS2CLK calculation. - */ - freq = clock_get(CLOCK_AHB) / CONFIG_SYS_RAM_FREQ_DIV; - - writel(CONFIG_SYS_RAM_FREQ_DIV << FMC_SDCR_SDCLK_SHIFT - | SDRAM_RPIPE << FMC_SDCR_RPIPE_SHIFT - | SDRAM_RBURST << FMC_SDCR_RBURST_SHIFT, - &STM32_SDRAM_FMC->sdcr1); - - writel(CONFIG_SYS_RAM_FREQ_DIV << FMC_SDCR_SDCLK_SHIFT - | SDRAM_CAS << FMC_SDCR_CAS_SHIFT - | SDRAM_NB << FMC_SDCR_NB_SHIFT - | SDRAM_MWID << FMC_SDCR_MWID_SHIFT - | SDRAM_NR << FMC_SDCR_NR_SHIFT - | SDRAM_NC << FMC_SDCR_NC_SHIFT - | SDRAM_RPIPE << FMC_SDCR_RPIPE_SHIFT - | SDRAM_RBURST << FMC_SDCR_RBURST_SHIFT, - &STM32_SDRAM_FMC->sdcr2); - - writel(SDRAM_TRP << FMC_SDTR_TRP_SHIFT - | SDRAM_TRC << FMC_SDTR_TRC_SHIFT, - &STM32_SDRAM_FMC->sdtr1); - - writel(SDRAM_TRCD << FMC_SDTR_TRCD_SHIFT - | SDRAM_TRP << FMC_SDTR_TRP_SHIFT - | SDRAM_TWR << FMC_SDTR_TWR_SHIFT - | SDRAM_TRC << FMC_SDTR_TRC_SHIFT - | SDRAM_TRAS << FMC_SDTR_TRAS_SHIFT - | SDRAM_TXSR << FMC_SDTR_TXSR_SHIFT - | SDRAM_TMRD << FMC_SDTR_TMRD_SHIFT, - &STM32_SDRAM_FMC->sdtr2); - - writel(FMC_SDCMR_BANK_2 | FMC_SDCMR_MODE_START_CLOCK, - &STM32_SDRAM_FMC->sdcmr); - - udelay(200); /* 200 us delay, page 10, "Power-Up" */ - FMC_BUSY_WAIT(); - - writel(FMC_SDCMR_BANK_2 | FMC_SDCMR_MODE_PRECHARGE, - &STM32_SDRAM_FMC->sdcmr); - - udelay(100); - FMC_BUSY_WAIT(); - - writel((FMC_SDCMR_BANK_2 | FMC_SDCMR_MODE_AUTOREFRESH - | 7 << FMC_SDCMR_NRFS_SHIFT), &STM32_SDRAM_FMC->sdcmr); - - udelay(100); - FMC_BUSY_WAIT(); - - writel(FMC_SDCMR_BANK_2 | (SDRAM_MODE_BL << SDRAM_MODE_BL_SHIFT - | SDRAM_MODE_CAS << SDRAM_MODE_CAS_SHIFT) - << FMC_SDCMR_MODE_REGISTER_SHIFT | FMC_SDCMR_MODE_WRITE_MODE, - &STM32_SDRAM_FMC->sdcmr); - - udelay(100); - - FMC_BUSY_WAIT(); - - writel(FMC_SDCMR_BANK_2 | FMC_SDCMR_MODE_NORMAL, - &STM32_SDRAM_FMC->sdcmr); - - FMC_BUSY_WAIT(); + rv = uclass_get_device(UCLASS_RAM, 0, &dev); + if (rv) { + debug("DRAM init failed: %d\n", rv); + return rv; + }

- /* Refresh timer */ - writel(SDRAM_TREF, &STM32_SDRAM_FMC->sdrtr); + if (fdtdec_setup_memory_size() != 0) + rv = -EINVAL;

- /* - * Fill in global info with description of SRAM configuration - */ - gd->bd->bi_dram[0].start = CONFIG_SYS_RAM_BASE; - gd->bd->bi_dram[0].size = CONFIG_SYS_RAM_SIZE; + return rv; +}

- gd->ram_size = CONFIG_SYS_RAM_SIZE; +int dram_init_banksize(void) +{ + fdtdec_setup_memory_banksize();

- return rv; + return 0; }

static const struct stm32_serial_platdata serial_platdata = { diff --git a/configs/stm32f429-discovery_defconfig b/configs/stm32f429-discovery_defconfig index 9339e36..1cf3b6a 100644 --- a/configs/stm32f429-discovery_defconfig +++ b/configs/stm32f429-discovery_defconfig @@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_STM32=y CONFIG_STM32F4=y CONFIG_TARGET_STM32F429_DISCOVERY=y +CONFIG_DEFAULT_DEVICE_TREE="stm32f429-disco" CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk consoleblank=0 ignore_loglevel" @@ -14,7 +15,10 @@ CONFIG_SYS_PROMPT="U-Boot > " CONFIG_CMD_IMLS=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_TIMER=y +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y CONFIG_ENV_IS_IN_FLASH=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y -CONFIG_OF_LIBFDT=y +CONFIG_RAM=y +CONFIG_STM32_SDRAM=y diff --git a/include/configs/stm32f429-discovery.h b/include/configs/stm32f429-discovery.h index 024d75a..317b934 100644 --- a/include/configs/stm32f429-discovery.h +++ b/include/configs/stm32f429-discovery.h @@ -24,7 +24,6 @@ * Configuration of the external SDRAM memory */ #define CONFIG_NR_DRAM_BANKS 1 -#define CONFIG_SYS_RAM_SIZE (8 << 20) #define CONFIG_SYS_RAM_CS 1 #define CONFIG_SYS_RAM_FREQ_DIV 2 #define CONFIG_SYS_RAM_BASE 0xD0000000

From: Patrice Chotard patrice.chotard@st.com

This allows to support rcc MFD driver. By enabling all these flags, we need to increase malloc area to avoid crash during early stage.

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- configs/stm32f429-discovery_defconfig | 5 +++++ 1 file changed, 5 insertions(+)

diff --git a/configs/stm32f429-discovery_defconfig b/configs/stm32f429-discovery_defconfig index 1cf3b6a..15ff646 100644 --- a/configs/stm32f429-discovery_defconfig +++ b/configs/stm32f429-discovery_defconfig @@ -1,5 +1,6 @@ CONFIG_ARM=y CONFIG_STM32=y +CONFIG_SYS_MALLOC_F_LEN=0xF00 CONFIG_STM32F4=y CONFIG_TARGET_STM32F429_DISCOVERY=y CONFIG_DEFAULT_DEVICE_TREE="stm32f429-disco" @@ -18,7 +19,11 @@ CONFIG_CMD_TIMER=y CONFIG_OF_CONTROL=y CONFIG_OF_EMBED=y CONFIG_ENV_IS_IN_FLASH=y +CONFIG_MISC=y +CONFIG_STM32_RCC=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_RAM=y CONFIG_STM32_SDRAM=y +CONFIG_DM_RESET=y +CONFIG_STM32_RESET=y

From: Patrice Chotard patrice.chotard@st.com

In order to use common clock driver between STM32F4 and STM32F7, remove clock_get() call As APB_PSC is always set to 2, only case when clock_get(CLOCK_AHB) != clock_get(CLOCK_APB1) is kept

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- arch/arm/mach-stm32/stm32f4/timer.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-stm32/stm32f4/timer.c b/arch/arm/mach-stm32/stm32f4/timer.c index 163f461..00b1d4a 100644 --- a/arch/arm/mach-stm32/stm32f4/timer.c +++ b/arch/arm/mach-stm32/stm32f4/timer.c @@ -51,12 +51,8 @@ int timer_init(void)

setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);

- if (clock_get(CLOCK_AHB) == clock_get(CLOCK_APB1)) - writel((clock_get(CLOCK_APB1) / CONFIG_SYS_HZ_CLOCK) - 1, - &tim->psc); - else - writel(((clock_get(CLOCK_APB1) * 2) / CONFIG_SYS_HZ_CLOCK) - 1, - &tim->psc); + writel(((CONFIG_SYS_CLK_FREQ / 2) / CONFIG_SYS_HZ_CLOCK) - 1, + &tim->psc);

writel(0xFFFFFFFF, &tim->arr); writel(TIM_CR1_CEN, &tim->cr1);

From: Patrice Chotard patrice.chotard@st.com

Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers instead of board GPIO initialization.

Remove stm32_gpio.c which is no more used and migrate structs stm32_gpio_regs and stm32_gpio_priv into arch-stm32f4/gpio.h to not break compilation.

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- arch/arm/include/asm/arch-stm32f4/gpio.h | 20 ++- arch/arm/include/asm/arch-stm32f4/stm32.h | 10 -- board/st/stm32f429-discovery/stm32f429-discovery.c | 111 ------------- configs/stm32f429-discovery_defconfig | 3 + drivers/gpio/Makefile | 1 - drivers/gpio/stm32_gpio.c | 182 --------------------- include/configs/stm32f429-discovery.h | 1 - 7 files changed, 19 insertions(+), 309 deletions(-) delete mode 100644 drivers/gpio/stm32_gpio.c

diff --git a/arch/arm/include/asm/arch-stm32f4/gpio.h b/arch/arm/include/asm/arch-stm32f4/gpio.h index 831c542..6173fa1 100644 --- a/arch/arm/include/asm/arch-stm32f4/gpio.h +++ b/arch/arm/include/asm/arch-stm32f4/gpio.h @@ -131,6 +131,22 @@ struct stm32_gpio_ctl { enum stm32_gpio_af af; };

+struct stm32_gpio_regs { + u32 moder; /* GPIO port mode */ + u32 otyper; /* GPIO port output type */ + u32 ospeedr; /* GPIO port output speed */ + u32 pupdr; /* GPIO port pull-up/pull-down */ + u32 idr; /* GPIO port input data */ + u32 odr; /* GPIO port output data */ + u32 bsrr; /* GPIO port bit set/reset */ + u32 lckr; /* GPIO port configuration lock */ + u32 afr[2]; /* GPIO alternate function */ +}; + +struct stm32_gpio_priv { + struct stm32_gpio_regs *regs; +}; + static inline unsigned stm32_gpio_to_port(unsigned gpio) { return gpio / 16; @@ -141,8 +157,4 @@ static inline unsigned stm32_gpio_to_pin(unsigned gpio) return gpio % 16; }

-int stm32_gpio_config(const struct stm32_gpio_dsc *gpio_dsc, - const struct stm32_gpio_ctl *gpio_ctl); -int stm32_gpout_set(const struct stm32_gpio_dsc *gpio_dsc, int state); - #endif /* _STM32_GPIO_H_ */ diff --git a/arch/arm/include/asm/arch-stm32f4/stm32.h b/arch/arm/include/asm/arch-stm32f4/stm32.h index 889778c..0449fce 100644 --- a/arch/arm/include/asm/arch-stm32f4/stm32.h +++ b/arch/arm/include/asm/arch-stm32f4/stm32.h @@ -23,16 +23,6 @@

#define STM32_BUS_MASK 0xFFFF0000

-#define STM32_GPIOA_BASE (STM32_AHB1PERIPH_BASE + 0x0000) -#define STM32_GPIOB_BASE (STM32_AHB1PERIPH_BASE + 0x0400) -#define STM32_GPIOC_BASE (STM32_AHB1PERIPH_BASE + 0x0800) -#define STM32_GPIOD_BASE (STM32_AHB1PERIPH_BASE + 0x0C00) -#define STM32_GPIOE_BASE (STM32_AHB1PERIPH_BASE + 0x1000) -#define STM32_GPIOF_BASE (STM32_AHB1PERIPH_BASE + 0x1400) -#define STM32_GPIOG_BASE (STM32_AHB1PERIPH_BASE + 0x1800) -#define STM32_GPIOH_BASE (STM32_AHB1PERIPH_BASE + 0x1C00) -#define STM32_GPIOI_BASE (STM32_AHB1PERIPH_BASE + 0x2000) - /* * Register maps */ diff --git a/board/st/stm32f429-discovery/stm32f429-discovery.c b/board/st/stm32f429-discovery/stm32f429-discovery.c index c5f4573..3d90218 100644 --- a/board/st/stm32f429-discovery/stm32f429-discovery.c +++ b/board/st/stm32f429-discovery/stm32f429-discovery.c @@ -16,120 +16,14 @@

#include <asm/io.h> #include <asm/arch/stm32.h> -#include <asm/arch/gpio.h>

DECLARE_GLOBAL_DATA_PTR;

-const struct stm32_gpio_ctl gpio_ctl_gpout = { - .mode = STM32_GPIO_MODE_OUT, - .otype = STM32_GPIO_OTYPE_PP, - .speed = STM32_GPIO_SPEED_50M, - .pupd = STM32_GPIO_PUPD_NO, - .af = STM32_GPIO_AF0 -}; - -const struct stm32_gpio_ctl gpio_ctl_usart = { - .mode = STM32_GPIO_MODE_AF, - .otype = STM32_GPIO_OTYPE_PP, - .speed = STM32_GPIO_SPEED_50M, - .pupd = STM32_GPIO_PUPD_UP, - .af = STM32_GPIO_USART -}; - -static const struct stm32_gpio_dsc usart_gpio[] = { - {STM32_GPIO_PORT_X, STM32_GPIO_PIN_TX}, /* TX */ - {STM32_GPIO_PORT_X, STM32_GPIO_PIN_RX}, /* RX */ -}; - -int uart_setup_gpio(void) -{ - int i; - int rv = 0; - - for (i = 0; i < ARRAY_SIZE(usart_gpio); i++) { - rv = stm32_gpio_config(&usart_gpio[i], &gpio_ctl_usart); - if (rv) - goto out; - } - -out: - return rv; -} - -const struct stm32_gpio_ctl gpio_ctl_fmc = { - .mode = STM32_GPIO_MODE_AF, - .otype = STM32_GPIO_OTYPE_PP, - .speed = STM32_GPIO_SPEED_100M, - .pupd = STM32_GPIO_PUPD_NO, - .af = STM32_GPIO_AF12 -}; - -static const struct stm32_gpio_dsc ext_ram_fmc_gpio[] = { - /* Chip is LQFP144, see DM00077036.pdf for details */ - {STM32_GPIO_PORT_D, STM32_GPIO_PIN_10}, /* 79, FMC_D15 */ - {STM32_GPIO_PORT_D, STM32_GPIO_PIN_9}, /* 78, FMC_D14 */ - {STM32_GPIO_PORT_D, STM32_GPIO_PIN_8}, /* 77, FMC_D13 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_15}, /* 68, FMC_D12 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_14}, /* 67, FMC_D11 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_13}, /* 66, FMC_D10 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_12}, /* 65, FMC_D9 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_11}, /* 64, FMC_D8 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_10}, /* 63, FMC_D7 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_9}, /* 60, FMC_D6 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_8}, /* 59, FMC_D5 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_7}, /* 58, FMC_D4 */ - {STM32_GPIO_PORT_D, STM32_GPIO_PIN_1}, /* 115, FMC_D3 */ - {STM32_GPIO_PORT_D, STM32_GPIO_PIN_0}, /* 114, FMC_D2 */ - {STM32_GPIO_PORT_D, STM32_GPIO_PIN_15}, /* 86, FMC_D1 */ - {STM32_GPIO_PORT_D, STM32_GPIO_PIN_14}, /* 85, FMC_D0 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_1}, /* 142, FMC_NBL1 */ - {STM32_GPIO_PORT_E, STM32_GPIO_PIN_0}, /* 141, FMC_NBL0 */ - {STM32_GPIO_PORT_G, STM32_GPIO_PIN_5}, /* 90, FMC_A15, BA1 */ - {STM32_GPIO_PORT_G, STM32_GPIO_PIN_4}, /* 89, FMC_A14, BA0 */ - {STM32_GPIO_PORT_G, STM32_GPIO_PIN_1}, /* 57, FMC_A11 */ - {STM32_GPIO_PORT_G, STM32_GPIO_PIN_0}, /* 56, FMC_A10 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_15}, /* 55, FMC_A9 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_14}, /* 54, FMC_A8 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_13}, /* 53, FMC_A7 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_12}, /* 50, FMC_A6 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_5}, /* 15, FMC_A5 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_4}, /* 14, FMC_A4 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_3}, /* 13, FMC_A3 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_2}, /* 12, FMC_A2 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_1}, /* 11, FMC_A1 */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_0}, /* 10, FMC_A0 */ - {STM32_GPIO_PORT_B, STM32_GPIO_PIN_6}, /* 136, SDRAM_NE */ - {STM32_GPIO_PORT_F, STM32_GPIO_PIN_11}, /* 49, SDRAM_NRAS */ - {STM32_GPIO_PORT_G, STM32_GPIO_PIN_15}, /* 132, SDRAM_NCAS */ - {STM32_GPIO_PORT_C, STM32_GPIO_PIN_0}, /* 26, SDRAM_NWE */ - {STM32_GPIO_PORT_B, STM32_GPIO_PIN_5}, /* 135, SDRAM_CKE */ - {STM32_GPIO_PORT_G, STM32_GPIO_PIN_8}, /* 93, SDRAM_CLK */ -}; - -static int fmc_setup_gpio(void) -{ - int rv = 0; - int i; - - for (i = 0; i < ARRAY_SIZE(ext_ram_fmc_gpio); i++) { - rv = stm32_gpio_config(&ext_ram_fmc_gpio[i], - &gpio_ctl_fmc); - if (rv) - goto out; - } - -out: - return rv; -} - int dram_init(void) { int rv; struct udevice *dev;

- rv = fmc_setup_gpio(); - if (rv) - return rv; rv = uclass_get_device(UCLASS_RAM, 0, &dev); if (rv) { debug("DRAM init failed: %d\n", rv); @@ -156,11 +50,6 @@ u32 get_board_rev(void)

int board_early_init_f(void) { - int res; - - res = uart_setup_gpio(); - if (res) - return res; return 0; }

diff --git a/configs/stm32f429-discovery_defconfig b/configs/stm32f429-discovery_defconfig index ee50b35..52bd931 100644 --- a/configs/stm32f429-discovery_defconfig +++ b/configs/stm32f429-discovery_defconfig @@ -20,10 +20,13 @@ CONFIG_OF_CONTROL=y CONFIG_OF_EMBED=y CONFIG_ENV_IS_IN_FLASH=y CONFIG_CLK=y +CONFIG_DM_GPIO=y CONFIG_MISC=y CONFIG_STM32_RCC=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_STM32=y CONFIG_RAM=y CONFIG_STM32_SDRAM=y CONFIG_DM_RESET=y diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 201d7bf..8525679 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -48,7 +48,6 @@ obj-$(CONFIG_ADI_GPIO2) += adi_gpio2.o obj-$(CONFIG_TCA642X) += tca642x.o obj-$(CONFIG_SUNXI_GPIO) += sunxi_gpio.o obj-$(CONFIG_LPC32XX_GPIO) += lpc32xx_gpio.o -obj-$(CONFIG_STM32_GPIO) += stm32_gpio.o obj-$(CONFIG_STM32F7_GPIO) += stm32f7_gpio.o obj-$(CONFIG_GPIO_UNIPHIER) += gpio-uniphier.o obj-$(CONFIG_ZYNQ_GPIO) += zynq_gpio.o diff --git a/drivers/gpio/stm32_gpio.c b/drivers/gpio/stm32_gpio.c deleted file mode 100644 index c04cef4..0000000 --- a/drivers/gpio/stm32_gpio.c +++ /dev/null @@ -1,182 +0,0 @@ -/* - * (C) Copyright 2011 - * Yuri Tikhonov, Emcraft Systems, yur@emcraft.com - * - * (C) Copyright 2015 - * Kamil Lulko, kamil.lulko@gmail.com - * - * Copyright 2015 ATS Advanced Telematics Systems GmbH - * Copyright 2015 Konsulko Group, Matt Porter mporter@konsulko.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/io.h> -#include <linux/errno.h> -#include <asm/arch/stm32.h> -#include <asm/arch/gpio.h> - -DECLARE_GLOBAL_DATA_PTR; - -static const unsigned long io_base[] = { - STM32_GPIOA_BASE, STM32_GPIOB_BASE, STM32_GPIOC_BASE, - STM32_GPIOD_BASE, STM32_GPIOE_BASE, STM32_GPIOF_BASE, - STM32_GPIOG_BASE, STM32_GPIOH_BASE, STM32_GPIOI_BASE -}; - -struct stm32_gpio_regs { - u32 moder; /* GPIO port mode */ - u32 otyper; /* GPIO port output type */ - u32 ospeedr; /* GPIO port output speed */ - u32 pupdr; /* GPIO port pull-up/pull-down */ - u32 idr; /* GPIO port input data */ - u32 odr; /* GPIO port output data */ - u32 bsrr; /* GPIO port bit set/reset */ - u32 lckr; /* GPIO port configuration lock */ - u32 afr[2]; /* GPIO alternate function */ -}; - -#define CHECK_DSC(x) (!x || x->port > 8 || x->pin > 15) -#define CHECK_CTL(x) (!x || x->af > 15 || x->mode > 3 || x->otype > 1 || \ - x->pupd > 2 || x->speed > 3) - -int stm32_gpio_config(const struct stm32_gpio_dsc *dsc, - const struct stm32_gpio_ctl *ctl) -{ - struct stm32_gpio_regs *gpio_regs; - u32 i; - int rv; - - if (CHECK_DSC(dsc)) { - rv = -EINVAL; - goto out; - } - if (CHECK_CTL(ctl)) { - rv = -EINVAL; - goto out; - } - - gpio_regs = (struct stm32_gpio_regs *)io_base[dsc->port]; - - i = (dsc->pin & 0x07) * 4; - clrsetbits_le32(&gpio_regs->afr[dsc->pin >> 3], 0xF << i, ctl->af << i); - - i = dsc->pin * 2; - - clrsetbits_le32(&gpio_regs->moder, 0x3 << i, ctl->mode << i); - clrsetbits_le32(&gpio_regs->otyper, 0x3 << i, ctl->otype << i); - clrsetbits_le32(&gpio_regs->ospeedr, 0x3 << i, ctl->speed << i); - clrsetbits_le32(&gpio_regs->pupdr, 0x3 << i, ctl->pupd << i); - - rv = 0; -out: - return rv; -} - -int stm32_gpout_set(const struct stm32_gpio_dsc *dsc, int state) -{ - struct stm32_gpio_regs *gpio_regs; - int rv; - - if (CHECK_DSC(dsc)) { - rv = -EINVAL; - goto out; - } - - gpio_regs = (struct stm32_gpio_regs *)io_base[dsc->port]; - - if (state) - writel(1 << dsc->pin, &gpio_regs->bsrr); - else - writel(1 << (dsc->pin + 16), &gpio_regs->bsrr); - - rv = 0; -out: - return rv; -} - -int stm32_gpin_get(const struct stm32_gpio_dsc *dsc) -{ - struct stm32_gpio_regs *gpio_regs; - int rv; - - if (CHECK_DSC(dsc)) { - rv = -EINVAL; - goto out; - } - - gpio_regs = (struct stm32_gpio_regs *)io_base[dsc->port]; - rv = readl(&gpio_regs->idr) & (1 << dsc->pin); -out: - return rv; -} - -/* Common GPIO API */ - -int gpio_request(unsigned gpio, const char *label) -{ - return 0; -} - -int gpio_free(unsigned gpio) -{ - return 0; -} - -int gpio_direction_input(unsigned gpio) -{ - struct stm32_gpio_dsc dsc; - struct stm32_gpio_ctl ctl; - - dsc.port = stm32_gpio_to_port(gpio); - dsc.pin = stm32_gpio_to_pin(gpio); - ctl.af = STM32_GPIO_AF0; - ctl.mode = STM32_GPIO_MODE_IN; - ctl.otype = STM32_GPIO_OTYPE_PP; - ctl.pupd = STM32_GPIO_PUPD_NO; - ctl.speed = STM32_GPIO_SPEED_50M; - - return stm32_gpio_config(&dsc, &ctl); -} - -int gpio_direction_output(unsigned gpio, int value) -{ - struct stm32_gpio_dsc dsc; - struct stm32_gpio_ctl ctl; - int res; - - dsc.port = stm32_gpio_to_port(gpio); - dsc.pin = stm32_gpio_to_pin(gpio); - ctl.af = STM32_GPIO_AF0; - ctl.mode = STM32_GPIO_MODE_OUT; - ctl.pupd = STM32_GPIO_PUPD_NO; - ctl.speed = STM32_GPIO_SPEED_50M; - - res = stm32_gpio_config(&dsc, &ctl); - if (res < 0) - goto out; - res = stm32_gpout_set(&dsc, value); -out: - return res; -} - -int gpio_get_value(unsigned gpio) -{ - struct stm32_gpio_dsc dsc; - - dsc.port = stm32_gpio_to_port(gpio); - dsc.pin = stm32_gpio_to_pin(gpio); - - return stm32_gpin_get(&dsc); -} - -int gpio_set_value(unsigned gpio, int value) -{ - struct stm32_gpio_dsc dsc; - - dsc.port = stm32_gpio_to_port(gpio); - dsc.pin = stm32_gpio_to_pin(gpio); - - return stm32_gpout_set(&dsc, value); -} diff --git a/include/configs/stm32f429-discovery.h b/include/configs/stm32f429-discovery.h index 934acbc..1ad3698 100644 --- a/include/configs/stm32f429-discovery.h +++ b/include/configs/stm32f429-discovery.h @@ -41,7 +41,6 @@ #define CONFIG_RED_LED 110 #define CONFIG_GREEN_LED 109

-#define CONFIG_STM32_GPIO #define CONFIG_STM32_FLASH

#define CONFIG_STM32_HSE_HZ 8000000

From: Patrice Chotard patrice.chotard@st.com

This DT file comes from kernel v4.15-rc1

stm32f469-pinctrl.dtsi header has been updated with correct STMicroelectronics Copyright.

Remove the paragraph about writing to the Free Software Foundation's mailing address as requested by checkpatch.

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- arch/arm/dts/Makefile | 3 +- arch/arm/dts/stm32f469-disco.dts | 129 ++++++++++++++++++++++++++++++++++++ arch/arm/dts/stm32f469-pinctrl.dtsi | 97 +++++++++++++++++++++++++++ 3 files changed, 228 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/stm32f469-disco.dts create mode 100644 arch/arm/dts/stm32f469-pinctrl.dtsi

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 77fac9e..15ea108 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -210,7 +210,8 @@ dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \

dtb-$(CONFIG_ARCH_SNAPDRAGON) += dragonboard410c.dtb

-dtb-$(CONFIG_STM32F4) += stm32f429-disco.dtb +dtb-$(CONFIG_STM32F4) += stm32f429-disco.dtb \ + stm32f469-disco.dtb

dtb-$(CONFIG_STM32F7) += stm32f746-disco.dtb \ stm32f769-disco.dtb diff --git a/arch/arm/dts/stm32f469-disco.dts b/arch/arm/dts/stm32f469-disco.dts new file mode 100644 index 0000000..67b19dc --- /dev/null +++ b/arch/arm/dts/stm32f469-disco.dts @@ -0,0 +1,129 @@ +/* + * Copyright 2016 - Lee Jones lee.jones@linaro.org + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "stm32f429.dtsi" +#include "stm32f469-pinctrl.dtsi" + +/ { + model = "STMicroelectronics STM32F469i-DISCO board"; + compatible = "st,stm32f469i-disco", "st,stm32f469"; + + chosen { + bootargs = "root=/dev/ram"; + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x00000000 0x1000000>; + }; + + aliases { + serial0 = &usart3; + }; + + soc { + dma-ranges = <0xc0000000 0x0 0x10000000>; + }; + + /* This turns on vbus for otg for host mode (dwc2) */ + vcc5v_otg: vcc5v-otg-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpiob 2 0>; + regulator-name = "vcc5_host1"; + regulator-always-on; + }; +}; + +&rcc { + compatible = "st,stm32f469-rcc", "st,stm32f42xx-rcc", "st,stm32-rcc"; +}; + +&clk_hse { + clock-frequency = <8000000>; +}; + +&rtc { + status = "okay"; +}; + +&timers1 { + status = "okay"; + + pwm { + pinctrl-0 = <&pwm1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + timer@0 { + status = "okay"; + }; +}; + +&timers3 { + status = "okay"; + + pwm { + pinctrl-0 = <&pwm3_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + timer@2 { + status = "okay"; + }; +}; + +&usart3 { + pinctrl-0 = <&usart3_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbotg_fs { + dr_mode = "host"; + pinctrl-0 = <&usbotg_fs_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/arch/arm/dts/stm32f469-pinctrl.dtsi b/arch/arm/dts/stm32f469-pinctrl.dtsi new file mode 100644 index 0000000..dd64158 --- /dev/null +++ b/arch/arm/dts/stm32f469-pinctrl.dtsi @@ -0,0 +1,97 @@ +/* + * Copyright (C) 2017, STMicroelectronics - All Rights Reserved + * Author(s): Alexandre Torgue alexandre.torgue@st.com for STMicroelectronics. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "stm32f4-pinctrl.dtsi" + +/ { + soc { + pinctrl: pin-controller { + compatible = "st,stm32f469-pinctrl"; + + gpioa: gpio@40020000 { + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpiob: gpio@40020400 { + gpio-ranges = <&pinctrl 0 16 16>; + }; + + gpioc: gpio@40020800 { + gpio-ranges = <&pinctrl 0 32 16>; + }; + + gpiod: gpio@40020c00 { + gpio-ranges = <&pinctrl 0 48 16>; + }; + + gpioe: gpio@40021000 { + gpio-ranges = <&pinctrl 0 64 16>; + }; + + gpiof: gpio@40021400 { + gpio-ranges = <&pinctrl 0 80 16>; + }; + + gpiog: gpio@40021800 { + gpio-ranges = <&pinctrl 0 96 16>; + }; + + gpioh: gpio@40021c00 { + gpio-ranges = <&pinctrl 0 112 16>; + }; + + gpioi: gpio@40022000 { + gpio-ranges = <&pinctrl 0 128 16>; + }; + + gpioj: gpio@40022400 { + gpio-ranges = <&pinctrl 0 144 6>, + <&pinctrl 12 156 4>; + }; + + gpiok: gpio@40022800 { + gpio-ranges = <&pinctrl 3 163 5>; + }; + }; + }; +};

From: Patrice Chotard patrice.chotard@st.com

This board offers :

_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory and 324 Kbytes of RAM in BGA216 package _ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability: _ Mbed-enabled (mbed.org) _ USB functions: USB virtual COM port, mass storage, debug port _ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive touch screen _ SAI Audio DAC, with a stereo headphone output jack _ 3 MEMS microphones _ MicroSD card connector _ I2C extension connector _ 4Mx32bit SDRAM _ 128-Mbit Quad-SPI NOR Flash _ Reset and wake-up buttons _ 4 color user LEDs _ USB OTG FS with Micro-AB connector _ Three power supply options: _ Expansion connectors and Arduino™ UNO V3 connectors

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- arch/arm/mach-stm32/stm32f4/Kconfig | 4 ++ board/st/stm32f469-discovery/Kconfig | 19 ++++++ board/st/stm32f469-discovery/MAINTAINERS | 6 ++ board/st/stm32f469-discovery/Makefile | 8 +++ board/st/stm32f469-discovery/stm32f469-discovery.c | 74 ++++++++++++++++++++++ configs/stm32f469-discovery_defconfig | 42 ++++++++++++ include/configs/stm32f469-discovery.h | 68 ++++++++++++++++++++ 7 files changed, 221 insertions(+) create mode 100644 board/st/stm32f469-discovery/Kconfig create mode 100644 board/st/stm32f469-discovery/MAINTAINERS create mode 100644 board/st/stm32f469-discovery/Makefile create mode 100644 board/st/stm32f469-discovery/stm32f469-discovery.c create mode 100644 configs/stm32f469-discovery_defconfig create mode 100644 include/configs/stm32f469-discovery.h

diff --git a/arch/arm/mach-stm32/stm32f4/Kconfig b/arch/arm/mach-stm32/stm32f4/Kconfig index a63619e..7005c65 100644 --- a/arch/arm/mach-stm32/stm32f4/Kconfig +++ b/arch/arm/mach-stm32/stm32f4/Kconfig @@ -3,6 +3,10 @@ if STM32F4 config TARGET_STM32F429_DISCOVERY bool "STM32F429 Discovery board"

+config TARGET_STM32F469_DISCOVERY + bool "STM32F469 Discovery board" + source "board/st/stm32f429-discovery/Kconfig" +source "board/st/stm32f469-discovery/Kconfig"

endif diff --git a/board/st/stm32f469-discovery/Kconfig b/board/st/stm32f469-discovery/Kconfig new file mode 100644 index 0000000..de61b6f --- /dev/null +++ b/board/st/stm32f469-discovery/Kconfig @@ -0,0 +1,19 @@ +if TARGET_STM32F469_DISCOVERY + +config SYS_BOARD + string + default "stm32f469-discovery" + +config SYS_VENDOR + string + default "st" + +config SYS_SOC + string + default "stm32f4" + +config SYS_CONFIG_NAME + string + default "stm32f469-discovery" + +endif diff --git a/board/st/stm32f469-discovery/MAINTAINERS b/board/st/stm32f469-discovery/MAINTAINERS new file mode 100644 index 0000000..d3c791a --- /dev/null +++ b/board/st/stm32f469-discovery/MAINTAINERS @@ -0,0 +1,6 @@ +STM32F469-DISCOVERY BOARD +M: Patrice Chotard patrice.chotard@st.com +S: Maintained +F: board/st/stm32f469-discovery/ +F: include/configs/stm32f469-discovery.h +F: configs/stm32f469-discovery_defconfig diff --git a/board/st/stm32f469-discovery/Makefile b/board/st/stm32f469-discovery/Makefile new file mode 100644 index 0000000..9ecd61e --- /dev/null +++ b/board/st/stm32f469-discovery/Makefile @@ -0,0 +1,8 @@ +# +# Copyright (C) STMicroelectronics SA 2017 +# Author(s): Patrice CHOTARD, patrice.chotard@st.com for STMicroelectronics. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := stm32f469-discovery.o diff --git a/board/st/stm32f469-discovery/stm32f469-discovery.c b/board/st/stm32f469-discovery/stm32f469-discovery.c new file mode 100644 index 0000000..36f7b2e --- /dev/null +++ b/board/st/stm32f469-discovery/stm32f469-discovery.c @@ -0,0 +1,74 @@ +/* + * Copyright (C) STMicroelectronics SA 2017 + * Author(s): Patrice CHOTARD, patrice.chotard@st.com for STMicroelectronics. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <dm.h> + +#include <asm/io.h> +#include <asm/arch/stm32.h> + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + int rv; + struct udevice *dev; + + rv = uclass_get_device(UCLASS_RAM, 0, &dev); + if (rv) { + debug("DRAM init failed: %d\n", rv); + return rv; + } + + if (fdtdec_setup_memory_size() != 0) + rv = -EINVAL; + + return rv; +} + +int dram_init_banksize(void) +{ + fdtdec_setup_memory_banksize(); + + return 0; +} + +u32 get_board_rev(void) +{ + return 0; +} + +int board_early_init_f(void) +{ + return 0; +} + +int board_init(void) +{ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + return 0; +} + +#ifdef CONFIG_MISC_INIT_R +int misc_init_r(void) +{ + char serialno[25]; + u32 u_id_low, u_id_mid, u_id_high; + + if (!env_get("serial#")) { + u_id_low = readl(&STM32_U_ID->u_id_low); + u_id_mid = readl(&STM32_U_ID->u_id_mid); + u_id_high = readl(&STM32_U_ID->u_id_high); + sprintf(serialno, "%08x%08x%08x", + u_id_high, u_id_mid, u_id_low); + env_set("serial#", serialno); + } + + return 0; +} +#endif diff --git a/configs/stm32f469-discovery_defconfig b/configs/stm32f469-discovery_defconfig new file mode 100644 index 0000000..afffddf --- /dev/null +++ b/configs/stm32f469-discovery_defconfig @@ -0,0 +1,42 @@ +CONFIG_ARM=y +CONFIG_STM32=y +CONFIG_SYS_MALLOC_F_LEN=0xF00 +CONFIG_STM32F4=y +CONFIG_TARGET_STM32F469_DISCOVERY=y +CONFIG_DEFAULT_DEVICE_TREE="stm32f469-disco" +CONFIG_BOOTDELAY=3 +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="U-Boot > " +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_BOOTEFI_HELLO_COMPILE is not set +CONFIG_CMD_IMLS=y +CONFIG_CMD_GPT=y +# CONFIG_RANDOM_UUID is not set +CONFIG_CMD_MMC=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +# CONFIG_DOS_PARTITION is not set +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y +# CONFIG_BLK is not set +CONFIG_CLK=y +CONFIG_DM_GPIO=y +CONFIG_MISC=y +CONFIG_STM32_RCC=y +CONFIG_DM_MMC=y +CONFIG_ARM_PL180_MMCI=y +CONFIG_MTD_NOR_FLASH=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_STM32=y +CONFIG_RAM=y +CONFIG_STM32_SDRAM=y +CONFIG_DM_RESET=y +CONFIG_STM32_RESET=y +CONFIG_STM32X7_SERIAL=y diff --git a/include/configs/stm32f469-discovery.h b/include/configs/stm32f469-discovery.h new file mode 100644 index 0000000..1409999 --- /dev/null +++ b/include/configs/stm32f469-discovery.h @@ -0,0 +1,68 @@ +/* + * Copyright (C) STMicroelectronics SA 2017 + * Author(s): Patrice CHOTARD, patrice.chotard@st.com for STMicroelectronics. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_STM32F4DISCOVERY + +#define CONFIG_MISC_INIT_R + +#define CONFIG_SYS_FLASH_BASE 0x08000000 + +#define CONFIG_SYS_INIT_SP_ADDR 0x10010000 +#define CONFIG_SYS_TEXT_BASE 0x08000000 + +#define CONFIG_SYS_ICACHE_OFF +#define CONFIG_SYS_DCACHE_OFF + +/* + * Configuration of the external SDRAM memory + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_RAM_FREQ_DIV 2 +#define CONFIG_SYS_RAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_RAM_BASE +#define CONFIG_SYS_LOAD_ADDR 0x00400000 +#define CONFIG_LOADADDR 0x00400000 + +#define CONFIG_SYS_MAX_FLASH_SECT 12 +#define CONFIG_SYS_MAX_FLASH_BANKS 2 + +#define CONFIG_ENV_OFFSET (256 << 10) +#define CONFIG_ENV_SECT_SIZE (128 << 10) +#define CONFIG_ENV_SIZE (8 << 10) + +#define CONFIG_STM32_FLASH + +#define CONFIG_STM32_HSE_HZ 8000000 +#define CONFIG_SYS_CLK_FREQ 180000000 /* 180 MHz */ +#define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer is clocked at 1MHz */ + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +#define CONFIG_SYS_CBSIZE 1024 + +#define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) + +#define CONFIG_BOOTCOMMAND \ + "run boot_sd" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "boot_sd=mmc dev 0;fatload mmc 0 0x00700000 stm32f469-disco.dtb; fatload mmc 0 0x00008000 zImage; icache off; bootz 0x00008000 - 0x00700000" + +/* + * Command line configuration. + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING + +#endif /* __CONFIG_H */