Export create_tlb() as an inline function in mipsregs.h. It allows to remove the declaration of the function from the board files.

Then it will allow also to use this function very early in the boot when the stack is not usable.

Signed-off-by: Gregory CLEMENT gregory.clement@bootlin.com --- arch/mips/cpu/cpu.c | 10 ---------- arch/mips/include/asm/mipsregs.h | 11 +++++++++++ 2 files changed, 11 insertions(+), 10 deletions(-)

diff --git a/arch/mips/cpu/cpu.c b/arch/mips/cpu/cpu.c index 5c56ab0289..a403ff729b 100644 --- a/arch/mips/cpu/cpu.c +++ b/arch/mips/cpu/cpu.c @@ -28,16 +28,6 @@ int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) } #endif

-void write_one_tlb(int index, u32 pagemask, u32 hi, u32 low0, u32 low1) -{ - write_c0_entrylo0(low0); - write_c0_pagemask(pagemask); - write_c0_entrylo1(low1); - write_c0_entryhi(hi); - write_c0_index(index); - tlb_write_indexed(); -} - int arch_cpu_init(void) { mips_cache_probe(); diff --git a/arch/mips/include/asm/mipsregs.h b/arch/mips/include/asm/mipsregs.h index 48fa1f1f7f..930562ebb2 100644 --- a/arch/mips/include/asm/mipsregs.h +++ b/arch/mips/include/asm/mipsregs.h @@ -2005,6 +2005,17 @@ static inline unsigned int get_ebase_cpunum(void) return read_c0_ebase() & 0x3ff; }

+static inline void write_one_tlb(int index, u32 pagemask, u32 hi, u32 low0, + u32 low1) +{ + write_c0_entrylo0(low0); + write_c0_pagemask(pagemask); + write_c0_entrylo1(low1); + write_c0_entryhi(hi); + write_c0_index(index); + tlb_write_indexed(); +} + #endif /* !__ASSEMBLY__ */

#endif /* _ASM_MIPSREGS_H */

Adding device tree for Ocelot SoC (extract from Linux) and the 2 evaluation boards using this SoC: PCB120 and PCB132.

Adding device tree for Luton SoC (not yet in Linux) and the evaluation boards using this SoC: PCB91.

Signed-off-by: Gregory CLEMENT gregory.clement@bootlin.com --- arch/mips/dts/luton_pcb091.dts | 36 ++++++++ arch/mips/dts/mscc,luton.dtsi | 87 +++++++++++++++++++ arch/mips/dts/mscc,ocelot.dtsi | 132 +++++++++++++++++++++++++++++ arch/mips/dts/mscc,ocelot_pcb.dtsi | 37 ++++++++ arch/mips/dts/ocelot_pcb120.dts | 12 +++ arch/mips/dts/ocelot_pcb123.dts | 12 +++ 6 files changed, 316 insertions(+) create mode 100644 arch/mips/dts/luton_pcb091.dts create mode 100644 arch/mips/dts/mscc,luton.dtsi create mode 100644 arch/mips/dts/mscc,ocelot.dtsi create mode 100644 arch/mips/dts/mscc,ocelot_pcb.dtsi create mode 100644 arch/mips/dts/ocelot_pcb120.dts create mode 100644 arch/mips/dts/ocelot_pcb123.dts

diff --git a/arch/mips/dts/luton_pcb091.dts b/arch/mips/dts/luton_pcb091.dts new file mode 100644 index 0000000000..b5e0df8d04 --- /dev/null +++ b/arch/mips/dts/luton_pcb091.dts @@ -0,0 +1,36 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,luton.dtsi" + +/ { + model = "Luton PCB091 Reference Board"; + compatible = "mscc,luton-pcb091", "mscc,luton"; + + aliases { + serial0 = &uart0; + spi0 = &spi0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + spi-flash@0 { + compatible = "spi-flash"; + spi-max-frequency = <18000000>; /* input clock */ + reg = <0>; /* CS0 */ + }; +}; + diff --git a/arch/mips/dts/mscc,luton.dtsi b/arch/mips/dts/mscc,luton.dtsi new file mode 100644 index 0000000000..6a4ad2a5be --- /dev/null +++ b/arch/mips/dts/mscc,luton.dtsi @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#include <dt-bindings/gpio/gpio.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "mscc,luton"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "mips,mips24KEc"; + device_type = "cpu"; + reg = <0>; + }; + }; + + aliases { + serial0 = &uart0; + }; + + ahb_clk: ahb-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <208333333>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x60000000 0x10200000>; + + uart0: serial@10100000 { + pinctrl-0 = <&uart_pins>; + pinctrl-names = "default"; + + compatible = "ns16550a"; + reg = <0x10100000 0x20>; + clocks = <&ahb_clk>; + reg-io-width = <4>; + reg-shift = <2>; + + status = "disabled"; + }; + + gpio: pinctrl@70068 { + compatible = "mscc,luton-pinctrl"; + reg = <0x70068 0x68>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&gpio 0 0 32>; + + uart_pins: uart-pins { + pins = "GPIO_30", "GPIO_31"; + function = "uart"; + }; + + }; + + gpio_spi_bitbang: gpio@10000064 { + compatible = "mscc,spi-bitbang-gpio"; + reg = <0x10000064 0x4>; + gpio-controller; + #gpio-cells = <2>; + + }; + + spi0: spi-bitbang { + compatible = "spi-gpio"; + status = "okay"; + gpio-sck = <&gpio_spi_bitbang 6 0>; + gpio-miso = <&gpio_spi_bitbang 0 0>; + gpio-mosi = <&gpio_spi_bitbang 5 0>; + cs-gpios = <&gpio_spi_bitbang 1 0>; + num-chipselects = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; diff --git a/arch/mips/dts/mscc,ocelot.dtsi b/arch/mips/dts/mscc,ocelot.dtsi new file mode 100644 index 0000000000..81afdffd4b --- /dev/null +++ b/arch/mips/dts/mscc,ocelot.dtsi @@ -0,0 +1,132 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "mscc,ocelot"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "mips,mips24KEc"; + device_type = "cpu"; + clocks = <&cpu_clk>; + reg = <0>; + }; + }; + + aliases { + serial0 = &uart0; + }; + + cpuintc: interrupt-controller@0 { + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + compatible = "mti,cpu-interrupt-controller"; + }; + + cpu_clk: cpu-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <500000000>; + }; + + ahb_clk: ahb-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <250000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x70000000 0x2000000>; + + interrupt-parent = <&intc>; + + cpu_ctrl: syscon@0 { + compatible = "mscc,ocelot-cpu-syscon", "syscon"; + reg = <0x0 0x2c>; + }; + + intc: interrupt-controller@70 { + compatible = "mscc,ocelot-icpu-intr"; + reg = <0x70 0x70>; + #interrupt-cells = <1>; + interrupt-controller; + interrupt-parent = <&cpuintc>; + interrupts = <2>; + }; + + uart0: serial@100000 { + pinctrl-0 = <&uart_pins>; + pinctrl-names = "default"; + compatible = "ns16550a"; + reg = <0x100000 0x20>; + interrupts = <6>; + clocks = <&ahb_clk>; + reg-io-width = <4>; + reg-shift = <2>; + + status = "disabled"; + }; + + uart2: serial@100800 { + pinctrl-0 = <&uart2_pins>; + pinctrl-names = "default"; + compatible = "ns16550a"; + reg = <0x100800 0x20>; + interrupts = <7>; + clocks = <&ahb_clk>; + reg-io-width = <4>; + reg-shift = <2>; + + status = "disabled"; + }; + + spi0: spi-master@101000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-ssi"; + reg = <0x101000 0x40>; + num-chipselect = <4>; + bus-num = <0>; + reg-io-width = <4>; + reg-shift = <2>; + spi-max-frequency = <18000000>; /* input clock */ + clocks = <&ahb_clk>; + + status = "disabled"; + }; + + reset@1070008 { + compatible = "mscc,ocelot-chip-reset"; + reg = <0x1070008 0x4>; + }; + + gpio: pinctrl@1070034 { + compatible = "mscc,ocelot-pinctrl"; + reg = <0x1070034 0x68>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&gpio 0 0 22>; + + uart_pins: uart-pins { + pins = "GPIO_6", "GPIO_7"; + function = "uart"; + }; + + uart2_pins: uart2-pins { + pins = "GPIO_12", "GPIO_13"; + function = "uart2"; + }; + }; + }; +}; diff --git a/arch/mips/dts/mscc,ocelot_pcb.dtsi b/arch/mips/dts/mscc,ocelot_pcb.dtsi new file mode 100644 index 0000000000..4e532363c3 --- /dev/null +++ b/arch/mips/dts/mscc,ocelot_pcb.dtsi @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,ocelot.dtsi" + +/ { + compatible = "mscc,ocelot"; + + aliases { + spi0 = &spi0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + spi-flash@0 { + compatible = "spi-flash"; + spi-max-frequency = <18000000>; /* input clock */ + reg = <0>; /* CS0 */ + }; +}; + +&ethernet { + status = "okay"; +}; diff --git a/arch/mips/dts/ocelot_pcb120.dts b/arch/mips/dts/ocelot_pcb120.dts new file mode 100644 index 0000000000..47d305a614 --- /dev/null +++ b/arch/mips/dts/ocelot_pcb120.dts @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,ocelot_pcb.dtsi" + +/ { + model = "Ocelot PCB120 Reference Board"; + compatible = "mscc,ocelot-pcb120", "mscc,ocelot"; +}; diff --git a/arch/mips/dts/ocelot_pcb123.dts b/arch/mips/dts/ocelot_pcb123.dts new file mode 100644 index 0000000000..17d8d326ce --- /dev/null +++ b/arch/mips/dts/ocelot_pcb123.dts @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,ocelot_pcb.dtsi" + +/ { + model = "Ocelot PCB123 Reference Board"; + compatible = "mscc,ocelot-pcb123", "mscc,ocelot"; +};

The kernels built for the Vcore III linux kernel have different expectation in the way the data were passed.

Unlike with yamon, the command line is expected to be a single string passed in argv[1]. An other expectation is that the arguments are located in the cached address space.

However, like yamon, they expect that rd_start and rd_size was passed by the bootloader in the command line of the kernel, and besides that it also wait for the root=/dev/ram0.

Signed-off-by: Gregory CLEMENT gregory.clement@bootlin.com --- arch/mips/lib/bootm.c | 62 +++++++++++++++++++++++++++++-------------- 1 file changed, 42 insertions(+), 20 deletions(-)

diff --git a/arch/mips/lib/bootm.c b/arch/mips/lib/bootm.c index deca5189e3..417f5ce452 100644 --- a/arch/mips/lib/bootm.c +++ b/arch/mips/lib/bootm.c @@ -44,22 +44,38 @@ void arch_lmb_reserve(struct lmb *lmb) lmb_reserve(lmb, sp, gd->ram_top - sp); }

-static void linux_cmdline_init(void) +static void linux_cmdline_init(int vcoreiii) { + if (!vcoreiii) { + linux_argv = (char **)UNCACHED_SDRAM(gd->bd->bi_boot_params); + linux_argp = (char *)(linux_argv + LINUX_MAX_ARGS); + } else { + /* + * Vcore III linux kernels expect arguments in the cached + * address space. They also expect the command line being a + * single string in the first argument + */ + linux_argv = (char **)(gd->bd->bi_boot_params); + linux_argp = (char *)(linux_argv + LINUX_MAX_ARGS); + linux_argv[1] = linux_argp; + } linux_argc = 1; - linux_argv = (char **)UNCACHED_SDRAM(gd->bd->bi_boot_params); linux_argv[0] = 0; - linux_argp = (char *)(linux_argv + LINUX_MAX_ARGS); }

-static void linux_cmdline_set(const char *value, size_t len) +static void linux_cmdline_set(const char *value, size_t len, int vcoreiii) { - linux_argv[linux_argc] = linux_argp; memcpy(linux_argp, value, len); - linux_argp[len] = 0; - + if (!vcoreiii) { + linux_argv[linux_argc] = linux_argp; + linux_argp[len] = 0; + linux_argc++; + } else { + linux_argp[len] = ' '; + linux_argp[len + 1] = 0; + linux_argc = 2; + } linux_argp += len + 1; - linux_argc++; }

static void linux_cmdline_dump(void) @@ -73,12 +89,10 @@ static void linux_cmdline_dump(void) debug(" arg %03d: %s\n", i, linux_argv[i]); }

-static void linux_cmdline_legacy(bootm_headers_t *images) +static void linux_cmdline_legacy(bootm_headers_t *images, int vcoreiii) { const char *bootargs, *next, *quote; - - linux_cmdline_init(); - + linux_cmdline_init(vcoreiii); bootargs = env_get("bootargs"); if (!bootargs) return; @@ -104,7 +118,7 @@ static void linux_cmdline_legacy(bootm_headers_t *images) if (!next) next = bootargs + strlen(bootargs);

- linux_cmdline_set(bootargs, next - bootargs); + linux_cmdline_set(bootargs, next - bootargs, vcoreiii);

if (*next) next++; @@ -113,7 +127,7 @@ static void linux_cmdline_legacy(bootm_headers_t *images) } }

-static void linux_cmdline_append(bootm_headers_t *images) +static void linux_cmdline_append(bootm_headers_t *images, int vcoreiii) { char buf[24]; ulong mem, rd_start, rd_size; @@ -121,7 +135,7 @@ static void linux_cmdline_append(bootm_headers_t *images) /* append mem */ mem = gd->ram_size >> 20; sprintf(buf, "mem=%luM", mem); - linux_cmdline_set(buf, strlen(buf)); + linux_cmdline_set(buf, strlen(buf), vcoreiii);

/* append rd_start and rd_size */ rd_start = images->initrd_start; @@ -129,9 +143,13 @@ static void linux_cmdline_append(bootm_headers_t *images)

if (rd_size) { sprintf(buf, "rd_start=0x%08lX", rd_start); - linux_cmdline_set(buf, strlen(buf)); + linux_cmdline_set(buf, strlen(buf), vcoreiii); sprintf(buf, "rd_size=0x%lX", rd_size); - linux_cmdline_set(buf, strlen(buf)); + linux_cmdline_set(buf, strlen(buf), vcoreiii); + if (vcoreiii) { + sprintf(buf, "root=/dev/ram0"); + linux_cmdline_set(buf, strlen(buf), vcoreiii); + } } }

@@ -276,11 +294,15 @@ static void boot_prep_linux(bootm_headers_t *images) boot_reloc_fdt(images); boot_setup_fdt(images); } else { - if (CONFIG_IS_ENABLED(MIPS_BOOT_CMDLINE_LEGACY)) { - linux_cmdline_legacy(images); + if (CONFIG_IS_ENABLED(SOC_VCOREIII)) { + linux_cmdline_legacy(images, 1); + linux_cmdline_append(images, 1); + linux_cmdline_dump(); + } else if (CONFIG_IS_ENABLED(MIPS_BOOT_CMDLINE_LEGACY)) { + linux_cmdline_legacy(images, 0);

if (!CONFIG_IS_ENABLED(MIPS_BOOT_ENV_LEGACY)) - linux_cmdline_append(images); + linux_cmdline_append(images, 0);

linux_cmdline_dump(); }

These families of SoCs are found in the Microsemi Switches solution.

Currently the support for two families support is added: - Ocelot (VSC7513, VSC7514) already supported in Linux - Luton (Luton10: VSC7423, VSC7424, VSC7428 and Luton26: VSC7425, VSC7426, VSC7426, VSC7427, VSC7429)

Signed-off-by: Gregory CLEMENT gregory.clement@bootlin.com --- Hi,

Actually this is the second version of this patch.

Compared to the previous version which did not reach the mailing list, I remove a lot of unused defines in the header. They can be add later when needed.

Sorry for the noise

Gregory

arch/mips/Kconfig | 6 + arch/mips/Makefile | 1 + arch/mips/mach-mscc/Kconfig | 101 +++ arch/mips/mach-mscc/Makefile | 6 + arch/mips/mach-mscc/cpu.c | 72 ++ arch/mips/mach-mscc/dram.c | 62 ++ arch/mips/mach-mscc/include/ioremap.h | 49 ++ arch/mips/mach-mscc/include/mach/cache.h | 36 + arch/mips/mach-mscc/include/mach/common.h | 31 + arch/mips/mach-mscc/include/mach/ddr.h | 753 ++++++++++++++++++ .../mips/mach-mscc/include/mach/luton/luton.h | 37 + .../include/mach/luton/luton_devcpu_gcb.h | 16 + .../include/mach/luton/luton_icpu_cfg.h | 247 ++++++ .../mach-mscc/include/mach/ocelot/ocelot.h | 35 + .../include/mach/ocelot/ocelot_devcpu_gcb.h | 49 ++ .../include/mach/ocelot/ocelot_icpu_cfg.h | 278 +++++++ arch/mips/mach-mscc/include/mach/tlb.h | 65 ++ arch/mips/mach-mscc/lowlevel_init.S | 29 + arch/mips/mach-mscc/lowlevel_init_luton.S | 63 ++ arch/mips/mach-mscc/reset.c | 37 + 20 files changed, 1973 insertions(+) create mode 100644 arch/mips/mach-mscc/Kconfig create mode 100644 arch/mips/mach-mscc/Makefile create mode 100644 arch/mips/mach-mscc/cpu.c create mode 100644 arch/mips/mach-mscc/dram.c create mode 100644 arch/mips/mach-mscc/include/ioremap.h create mode 100644 arch/mips/mach-mscc/include/mach/cache.h create mode 100644 arch/mips/mach-mscc/include/mach/common.h create mode 100644 arch/mips/mach-mscc/include/mach/ddr.h create mode 100644 arch/mips/mach-mscc/include/mach/luton/luton.h create mode 100644 arch/mips/mach-mscc/include/mach/luton/luton_devcpu_gcb.h create mode 100644 arch/mips/mach-mscc/include/mach/luton/luton_icpu_cfg.h create mode 100644 arch/mips/mach-mscc/include/mach/ocelot/ocelot.h create mode 100644 arch/mips/mach-mscc/include/mach/ocelot/ocelot_devcpu_gcb.h create mode 100644 arch/mips/mach-mscc/include/mach/ocelot/ocelot_icpu_cfg.h create mode 100644 arch/mips/mach-mscc/include/mach/tlb.h create mode 100644 arch/mips/mach-mscc/lowlevel_init.S create mode 100644 arch/mips/mach-mscc/lowlevel_init_luton.S create mode 100644 arch/mips/mach-mscc/reset.c

diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 6e5e0ffe65..c4fc3d077b 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -58,6 +58,11 @@ config ARCH_ATH79 select OF_CONTROL imply CMD_DM

+config ARCH_MSCC + bool "Support MSCC VCore-III" + select OF_CONTROL + select DM + config ARCH_BMIPS bool "Support BMIPS SoCs" select CLK @@ -118,6 +123,7 @@ source "board/imgtec/xilfpga/Kconfig" source "board/micronas/vct/Kconfig" source "board/qemu-mips/Kconfig" source "arch/mips/mach-ath79/Kconfig" +source "arch/mips/mach-mscc/Kconfig" source "arch/mips/mach-bmips/Kconfig" source "arch/mips/mach-pic32/Kconfig"

diff --git a/arch/mips/Makefile b/arch/mips/Makefile index a36f5f1fb6..acb1340942 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -14,6 +14,7 @@ libs-y += arch/mips/lib/ machine-$(CONFIG_ARCH_ATH79) += ath79 machine-$(CONFIG_ARCH_BMIPS) += bmips machine-$(CONFIG_MACH_PIC32) += pic32 +machine-$(CONFIG_ARCH_MSCC) += mscc

machdirs := $(patsubst %,arch/mips/mach-%/,$(machine-y)) libs-y += $(machdirs) diff --git a/arch/mips/mach-mscc/Kconfig b/arch/mips/mach-mscc/Kconfig new file mode 100644 index 0000000000..20148bfe15 --- /dev/null +++ b/arch/mips/mach-mscc/Kconfig @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +if ARCH_MSCC + +config SYS_DCACHE_SIZE + default 32768 + +config SYS_DCACHE_LINE_SIZE + default 32 + +config SYS_ICACHE_SIZE + default 32768 + +config SYS_ICACHE_LINE_SIZE + default 32 + +endif + +menu "MSCC VCore-III platforms" + depends on ARCH_MSCC + +config SOC_VCOREIII + select SUPPORTS_LITTLE_ENDIAN + select SUPPORTS_BIG_ENDIAN + select SUPPORTS_CPU_MIPS32_R1 + select SUPPORTS_CPU_MIPS32_R2 + select ROM_EXCEPTION_VECTORS + select MIPS_TUNE_24KC + bool + +config SYS_SOC + default "mscc" + +config SOC_OCELOT + bool + select SOC_VCOREIII + help + This supports MSCC Ocelot family of SOCs. + +config SOC_LUTON + bool + select SOC_VCOREIII + help + This supports MSCC Luton family of SOCs. + +config SYS_CONFIG_NAME + default "vcoreiii" + +choice + prompt "Board select" + +config TARGET_OCELOT_PCB120 + bool "MSCC PCB120 Reference Board (aka VSC5635EV)" + select SOC_OCELOT + help + When selected, CONFIG_DEFAULT_DEVICE_TREE should be set to + ocelot_pcb120 + +config TARGET_OCELOT_PCB123 + bool "MSCC PCB123 Reference Board (aka VSC7514EV))" + select SOC_OCELOT + help + When selected, CONFIG_DEFAULT_DEVICE_TREE should be set to + ocelot_pcb123 + +config TARGET_LUTON_PCB091 + bool "MSCC PCB091 Reference Board" + select SOC_LUTON + select MSCC_BITBANG_SPI_GPIO + help + When selected, CONFIG_DEFAULT_DEVICE_TREE should be set to + luton_pcb091 +endchoice + +choice + prompt "DDR type" + +config DDRTYPE_H5TQ4G63MFR + bool "Hynix H5TQ4G63MFR-PBC (4Gbit, DDR3-800, 256Mbitx16)" + +config DDRTYPE_MT41K256M16 + bool "Micron MT41K256M16 (4Gbit, DDR3L-800, 256Mbitx16)" + +config DDRTYPE_H5TQ1G63BFA + bool "Hynix H5TQ1G63BFA (1Gbit DDR3, x16)" + +config DDRTYPE_MT41J128M16HA + bool "Micron MT41J128M16HA-15E:D (2Gbit DDR3, x16)" + +config DDRTYPE_MT41K128M16JT + bool "Micron MT41K128M16JT-125 (2Gbit DDR3L, 128Mbitx16)" + +config DDRTYPE_MT47H128M8HQ + bool "Micron MT47H128M8-3 (1Gbit, DDR-533@CL4 @ 4.80ns 16Mbisx8x8)" + +endchoice + +source "board/mscc/ocelot/Kconfig" +source "board/mscc/luton/Kconfig" + +endmenu diff --git a/arch/mips/mach-mscc/Makefile b/arch/mips/mach-mscc/Makefile new file mode 100644 index 0000000000..6c60f26ca4 --- /dev/null +++ b/arch/mips/mach-mscc/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +CFLAGS_cpu.o += -finline-limit=64000 + +obj-y += cpu.o dram.o reset.o lowlevel_init.o +obj-$(CONFIG_SOC_LUTON) += lowlevel_init_luton.o diff --git a/arch/mips/mach-mscc/cpu.c b/arch/mips/mach-mscc/cpu.c new file mode 100644 index 0000000000..3d6dd78c61 --- /dev/null +++ b/arch/mips/mach-mscc/cpu.c @@ -0,0 +1,72 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#include <common.h> + +#include <asm/io.h> +#include <asm/types.h> + +#include <mach/tlb.h> +#include <mach/ddr.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* NOTE: lowlevel_init() function does not have access to the + * stack. Thus, all called functions must be inlined, and (any) local + * variables must be kept in registers. + */ +void vcoreiii_tlb_init(void) +{ + register int tlbix = 0; + + init_tlb(); + + /* 0x70000000 size 32M (0x02000000) */ + create_tlb(tlbix++, MSCC_IO_ORIGIN1_OFFSET, SZ_16M, MMU_REGIO_RW, MMU_REGIO_RW); +#ifdef CONFIG_SOC_LUTON + create_tlb(tlbix++, MSCC_IO_ORIGIN2_OFFSET, SZ_16M, MMU_REGIO_RW, MMU_REGIO_RW); +#endif + /* 0x40000000 - 0x43ffffff - NON-CACHED! */ + /* Flash CS0-3, each 16M = 64M total (16 x 4 below ) */ + create_tlb(tlbix++, MSCC_FLASH_TO, SZ_16M, MMU_REGIO_RO, MMU_REGIO_RO); + create_tlb(tlbix++, MSCC_FLASH_TO+SZ_32M, SZ_16M, MMU_REGIO_RO, MMU_REGIO_RO); + + /* 0x20000000 - up */ +#if CONFIG_SYS_SDRAM_SIZE <= SZ_64M + create_tlb(tlbix++, MSCC_DDR_TO, SZ_64M, MMU_REGIO_RW, MMU_REGIO_INVAL); +#elif CONFIG_SYS_SDRAM_SIZE <= SZ_128M + create_tlb(tlbix++, MSCC_DDR_TO, SZ_64M, MMU_REGIO_RW, MMU_REGIO_RW); +#elif CONFIG_SYS_SDRAM_SIZE <= SZ_256M + create_tlb(tlbix++, MSCC_DDR_TO, SZ_256M, MMU_REGIO_RW, MMU_REGIO_INVAL); +#elif CONFIG_SYS_SDRAM_SIZE <= SZ_512M + create_tlb(tlbix++, MSCC_DDR_TO, SZ_256M, MMU_REGIO_RW, MMU_REGIO_RW); +#else /* 1024M */ + create_tlb(tlbix++, MSCC_DDR_TO, SZ_512M, MMU_REGIO_RW, MMU_REGIO_RW); +#endif +} + +int mach_cpu_init(void) +{ + /* Speed up NOR flash access */ +#ifdef CONFIG_SOC_LUTON + writel(ICPU_SPI_MST_CFG_FAST_READ_ENA + +#else + writel( +#endif + ICPU_SPI_MST_CFG_CS_DESELECT_TIME(0x19) + + ICPU_SPI_MST_CFG_CLK_DIV(9), REG_CFG(ICPU_SPI_MST_CFG)); + + /* Disable all IRQs - map to destination map 0 */ + writel(0, REG_CFG(ICPU_INTR_ENA)); +#ifdef CONFIG_SOC_OCELOT + writel(~0, REG_CFG(ICPU_DST_INTR_MAP(0))); + writel(0, REG_CFG(ICPU_DST_INTR_MAP(1))); + writel(0, REG_CFG(ICPU_DST_INTR_MAP(2))); + writel(0, REG_CFG(ICPU_DST_INTR_MAP(3))); +#else + writel(ICPU_INTR_IRQ0_ENA_IRQ0_ENA, REG_CFG(ICPU_INTR_IRQ0_ENA)); +#endif + return 0; +} diff --git a/arch/mips/mach-mscc/dram.c b/arch/mips/mach-mscc/dram.c new file mode 100644 index 0000000000..2db9001fe9 --- /dev/null +++ b/arch/mips/mach-mscc/dram.c @@ -0,0 +1,62 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#include <common.h> + +#include <asm/io.h> +#include <asm/types.h> + +#include <mach/tlb.h> +#include <mach/ddr.h> + +DECLARE_GLOBAL_DATA_PTR; + +int vcoreiii_ddr_init(void) +{ + int res; + if (!(readl(REG_CFG(ICPU_MEMCTRL_STAT)) & + ICPU_MEMCTRL_STAT_INIT_DONE)) { + hal_vcoreiii_init_memctl(); + hal_vcoreiii_wait_memctl(); + if (hal_vcoreiii_init_dqs() != 0 || + hal_vcoreiii_train_bytelane(0) != 0 +#ifdef CONFIG_SOC_OCELOT + || hal_vcoreiii_train_bytelane(1) != 0 +#endif + ) + hal_vcoreiii_ddr_failed(); + } + +#if (CONFIG_SYS_TEXT_BASE != 0x20000000) + res = dram_check(); + if (res == 0) + hal_vcoreiii_ddr_verified(); + else + hal_vcoreiii_ddr_failed(); + + /* Clear boot-mode and read-back to activate/verify */ + writel(readl(REG_CFG(ICPU_GENERAL_CTRL))& ~ICPU_GENERAL_CTRL_BOOT_MODE_ENA, + REG_CFG(ICPU_GENERAL_CTRL)); + readl(REG_CFG(ICPU_GENERAL_CTRL)); +#else + res = 0; +#endif + return res; +} + +int print_cpuinfo(void) +{ + printf("MSCC VCore-III MIPS 24Kec\n"); + + return 0; +} + +int dram_init(void) +{ + while (vcoreiii_ddr_init()); + + gd->ram_size = CONFIG_SYS_SDRAM_SIZE; + return 0; +} diff --git a/arch/mips/mach-mscc/include/ioremap.h b/arch/mips/mach-mscc/include/ioremap.h new file mode 100644 index 0000000000..684f89168c --- /dev/null +++ b/arch/mips/mach-mscc/include/ioremap.h @@ -0,0 +1,49 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef __ASM_MACH_MSCC_IOREMAP_H +#define __ASM_MACH_MSCC_IOREMAP_H + +#include <linux/types.h> +#include <mach/common.h> + +/* + * Allow physical addresses to be fixed up to help peripherals located + * outside the low 32-bit range -- generic pass-through version. + */ +static inline phys_addr_t fixup_bigphys_addr(phys_addr_t phys_addr, + phys_addr_t size) +{ + return phys_addr; +} + +static inline int is_vcoreiii_internal_registers(phys_addr_t offset) +{ +#if defined(CONFIG_ARCH_MSCC) + if ((offset >= MSCC_IO_ORIGIN1_OFFSET && offset < (MSCC_IO_ORIGIN1_OFFSET+MSCC_IO_ORIGIN1_SIZE)) || + (offset >= MSCC_IO_ORIGIN2_OFFSET && offset < (MSCC_IO_ORIGIN2_OFFSET+MSCC_IO_ORIGIN2_SIZE))) + return 1; +#endif + + return 0; +} + +static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size, + unsigned long flags) +{ + if (is_vcoreiii_internal_registers(offset)) + return (void __iomem *)offset; + + return NULL; +} + +static inline int plat_iounmap(const volatile void __iomem *addr) +{ + return is_vcoreiii_internal_registers((unsigned long)addr); +} + +#define _page_cachable_default _CACHE_CACHABLE_NONCOHERENT + +#endif /* __ASM_MACH_MSCC_IOREMAP_H */ diff --git a/arch/mips/mach-mscc/include/mach/cache.h b/arch/mips/mach-mscc/include/mach/cache.h new file mode 100644 index 0000000000..f3d09014f3 --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/cache.h @@ -0,0 +1,36 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ +#define MIPS32_CACHE_OP(which, op) (which | (op << 2)) + +#define MIPS32_WHICH_ICACHE 0x0 +#define MIPS32_WHICH_DCACHE 0x1 + +#define MIPS32_INDEX_INVALIDATE 0x0 +#define MIPS32_INDEX_LOAD_TAG 0x1 +#define MIPS32_INDEX_STORE_TAG 0x2 +#define MIPS32_HIT_INVALIDATE 0x4 +#define MIPS32_ICACHE_FILL 0x5 +#define MIPS32_DCACHE_HIT_INVALIDATE 0x5 +#define MIPS32_DCACHE_HIT_WRITEBACK 0x6 +#define MIPS32_FETCH_AND_LOCK 0x7 + +#define ICACHE_LOAD_LOCK (MIPS32_CACHE_OP(MIPS32_WHICH_ICACHE, MIPS32_FETCH_AND_LOCK)) + +#define CACHE_LINE_LEN 32 + +/* Prefetch and lock instructions into cache */ +static inline void icache_lock(void *func, size_t len) +{ + int i, lines = ((len - 1) / CACHE_LINE_LEN) + 1; + for (i = 0; i < lines; i++) { + asm volatile (" cache %0, %1(%2)" + : /* No Output */ + : "I" ICACHE_LOAD_LOCK, + "n" (i*CACHE_LINE_LEN), + "r" (func) + : /* No Clobbers */); + } +} + diff --git a/arch/mips/mach-mscc/include/mach/common.h b/arch/mips/mach-mscc/include/mach/common.h new file mode 100644 index 0000000000..7e5c81c925 --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/common.h @@ -0,0 +1,31 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef __ASM_MACH_COMMON_H +#define __ASM_MACH_COMMON_H + +// Stick to using register offsets - matching readl()/writel() prototypes +#define MSCC_IOREG(t,o) ((void *)MSCC_IOADDR(t,o)) + +#if defined(CONFIG_SOC_OCELOT) +#include <mach/ocelot/ocelot.h> +#include <mach/ocelot/ocelot_devcpu_gcb.h> +#include <mach/ocelot/ocelot_icpu_cfg.h> +#elif defined(CONFIG_SOC_LUTON) +#include <mach/luton/luton.h> +#include <mach/luton/luton_devcpu_gcb.h> +#include <mach/luton/luton_icpu_cfg.h> +#else +#error Unsupported platform +#endif + +#define MSCC_DDR_TO 0x20000000 /* DDR RAM base offset */ +#define MSCC_MEMCTL1_TO 0x40000000 /* SPI/PI base offset */ +#define MSCC_MEMCTL2_TO 0x50000000 /* SPI/PI base offset */ +#define MSCC_FLASH_TO MSCC_MEMCTL1_TO /* Flash base offset */ + +#define VCOREIII_TIMER_DIVIDER 25 // Clock tick ~ 0.1 us + +#endif /* __ASM_MACH_COMMON_H */ diff --git a/arch/mips/mach-mscc/include/mach/ddr.h b/arch/mips/mach-mscc/include/mach/ddr.h new file mode 100644 index 0000000000..aef3facdca --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/ddr.h @@ -0,0 +1,753 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef __ASM_MACH_DDR_H +#define __ASM_MACH_DDR_H + +#include <mach/common.h> +#include <mach/cache.h> +#include <asm/reboot.h> + +#define MIPS_VCOREIII_MEMORY_DDR3 +#define MIPS_VCOREIII_DDR_SIZE CONFIG_SYS_SDRAM_SIZE + +#if defined(CONFIG_DDRTYPE_H5TQ1G63BFA) /* Serval1 Refboard */ + +/* Hynix H5TQ1G63BFA (1Gbit DDR3, x16) @ 3.20ns */ +#define VC3_MPAR_bank_addr_cnt 3 +#define VC3_MPAR_row_addr_cnt 13 +#define VC3_MPAR_col_addr_cnt 10 +#define VC3_MPAR_tREFI 2437 +#define VC3_MPAR_tRAS_min 12 +#define VC3_MPAR_CL 6 +#define VC3_MPAR_tWTR 4 +#define VC3_MPAR_tRC 16 +#define VC3_MPR_tFAW 16 +#define VC3_MPAR_tRP 5 +#define VC3_MPAR_tRRD 4 +#define VC3_MPAR_tRCD 5 +#define VC3_MPAR_tMRD 4 +#define VC3_MPAR_tRFC 35 +#define VC3_MPAR_CWL 5 +#define VC3_MPAR_tXPR 38 +#define VC3_MPAR_tMOD 12 +#define VC3_MPAR_tDLLK 512 +#define VC3_MPAR_tWR 5 + +#elif defined(CONFIG_DDRTYPE_MT41J128M16HA) /* Validation board */ + +/* Micron MT41J128M16HA-15E:D (2Gbit DDR3, x16) @ 3.20ns */ +#define VC3_MPAR_bank_addr_cnt 3 +#define VC3_MPAR_row_addr_cnt 14 +#define VC3_MPAR_col_addr_cnt 10 +#define VC3_MPAR_tREFI 2437 +#define VC3_MPAR_tRAS_min 12 +#define VC3_MPAR_CL 5 +#define VC3_MPAR_tWTR 4 +#define VC3_MPAR_tRC 16 +#define VC3_MPAR_tFAW 16 +#define VC3_MPAR_tRP 5 +#define VC3_MPAR_tRRD 4 +#define VC3_MPAR_tRCD 5 +#define VC3_MPAR_tMRD 4 +#define VC3_MPAR_tRFC 50 +#define VC3_MPAR_CWL 5 +#define VC3_MPAR_tXPR 54 +#define VC3_MPAR_tMOD 12 +#define VC3_MPAR_tDLLK 512 +#define VC3_MPAR_tWR 5 + +#elif defined(CONFIG_DDRTYPE_MT41K256M16) /* JR2 Validation board */ + +/* Micron MT41K256M16 (4Gbit, DDR3L-800, 256Mbitx16) @ 3.20ns */ +#define VC3_MPAR_bank_addr_cnt 3 +#define VC3_MPAR_row_addr_cnt 15 +#define VC3_MPAR_col_addr_cnt 10 +#define VC3_MPAR_tREFI 2437 +#define VC3_MPAR_tRAS_min 12 +#define VC3_MPAR_CL 5 +#define VC3_MPAR_tWTR 4 +#define VC3_MPAR_tRC 16 +#define VC3_MPAR_tFAW 16 +#define VC3_MPAR_tRP 5 +#define VC3_MPAR_tRRD 4 +#define VC3_MPAR_tRCD 5 +#define VC3_MPAR_tMRD 4 +#define VC3_MPAR_tRFC 82 +#define VC3_MPAR_CWL 5 +#define VC3_MPAR_tXPR 85 +#define VC3_MPAR_tMOD 12 +#define VC3_MPAR_tDLLK 512 +#define VC3_MPAR_tWR 5 + +#elif defined(CONFIG_DDRTYPE_H5TQ4G63MFR) /* JR2 Reference board */ + +/* Hynix H5TQ4G63MFR-PBC (4Gbit, DDR3-800, 256Mbitx16) - 2kb pages @ 3.20ns */ +#define VC3_MPAR_bank_addr_cnt 3 +#define VC3_MPAR_row_addr_cnt 15 +#define VC3_MPAR_col_addr_cnt 10 +#define VC3_MPAR_tREFI 2437 +#define VC3_MPAR_tRAS_min 12 +#define VC3_MPAR_CL 6 +#define VC3_MPAR_tWTR 4 +#define VC3_MPAR_tRC 17 +#define VC3_MPAR_tFAW 16 +#define VC3_MPAR_tRP 5 +#define VC3_MPAR_tRRD 4 +#define VC3_MPAR_tRCD 5 +#define VC3_MPAR_tMRD 4 +#define VC3_MPAR_tRFC 82 +#define VC3_MPAR_CWL 5 +#define VC3_MPAR_tXPR 85 +#define VC3_MPAR_tMOD 12 +#define VC3_MPAR_tDLLK 512 +#define VC3_MPAR_tWR 5 + +#elif defined(CONFIG_DDRTYPE_MT41K128M16JT) + +/* Micron Micron MT41K128M16JT-125 (2Gbit DDR3L, 128Mbitx16) @ 3.20ns */ +#define VC3_MPAR_bank_addr_cnt 3 +#define VC3_MPAR_row_addr_cnt 14 +#define VC3_MPAR_col_addr_cnt 10 +#define VC3_MPAR_tREFI 2437 +#define VC3_MPAR_tRAS_min 12 +#define VC3_MPAR_CL 6 +#define VC3_MPAR_tWTR 4 +#define VC3_MPAR_tRC 16 +#define VC3_MPAR_tFAW 16 +#define VC3_MPAR_tRP 5 +#define VC3_MPAR_tRRD 4 +#define VC3_MPAR_tRCD 5 +#define VC3_MPAR_tMRD 4 +#define VC3_MPAR_tRFC 82 +#define VC3_MPAR_CWL 5 +#define VC3_MPAR_tXPR 85 +#define VC3_MPAR_tMOD 12 +#define VC3_MPAR_tDLLK 512 +#define VC3_MPAR_tWR 5 + +#elif defined(CONFIG_DDRTYPE_MT47H128M8HQ) /* Luton10/26 Refboards */ + +/* Micron 1Gb MT47H128M8-3 16Meg x 8 x 8 banks, DDR-533@CL4 @ 4.80ns */ +#define VC3_MPAR_bank_addr_cnt 3 +#define VC3_MPAR_row_addr_cnt 14 +#define VC3_MPAR_col_addr_cnt 10 +#define VC3_MPAR_tREFI 1625 +#define VC3_MPAR_tRAS_min 9 +#define VC3_MPAR_CL 4 +#define VC3_MPAR_tWTR 2 +#define VC3_MPAR_tRC 12 +#define VC3_MPAR_tFAW 8 +#define VC3_MPAR_tRP 4 +#define VC3_MPAR_tRRD 2 +#define VC3_MPAR_tRCD 4 + +#define VC3_MPAR_tRPA 4 +#define VC3_MPAR_tRP 4 + +#define VC3_MPAR_tMRD 2 +#define VC3_MPAR_tRFC 27 + +#define VC3_MPAR__400_ns_dly 84 + +#define VC3_MPAR_tWR 4 +#undef MIPS_VCOREIII_MEMORY_DDR3 +#else + +#error Unknown DDR system configuration - please add! + +#endif + +#ifdef CONFIG_SOC_OCELOT +#define MIPS_VCOREIII_MEMORY_16BIT 1 +#endif + +#define MIPS_VCOREIII_MEMORY_SSTL_ODT 7 +#define MIPS_VCOREIII_MEMORY_SSTL_DRIVE 7 +#define VCOREIII_DDR_DQS_MODE_CALIBRATE + +#ifdef MIPS_VCOREIII_MEMORY_16BIT + #define VC3_MPAR_16BIT 1 +#else + #define VC3_MPAR_16BIT 0 +#endif + +#ifdef MIPS_VCOREIII_MEMORY_DDR3 + #define VC3_MPAR_DDR3_MODE 1 /* DDR3 */ + #define VC3_MPAR_BURST_LENGTH 8 /* Always 8 (1) for DDR3 */ + #ifdef MIPS_VCOREIII_MEMORY_16BIT +#define VC3_MPAR_BURST_SIZE 1 /* Always 1 for DDR3/16bit */ + #else + #define VC3_MPAR_BURST_SIZE 0 + #endif +#else + #define VC3_MPAR_DDR3_MODE 0 /* DDR2 */ + #ifdef MIPS_VCOREIII_MEMORY_16BIT + #define VC3_MPAR_BURST_LENGTH 4 /* in DDR2 16-bit mode, use burstlen 4 */ + #else + #define VC3_MPAR_BURST_LENGTH 8 /* For 8-bit IF we must run burst-8 */ + #endif + #define VC3_MPAR_BURST_SIZE 0 /* Always 0 for DDR2 */ +#endif + +#define VC3_MPAR_RL VC3_MPAR_CL +#if !defined(MIPS_VCOREIII_MEMORY_DDR3) +#define VC3_MPAR_WL (VC3_MPAR_RL-1) +#define VC3_MPAR_MD VC3_MPAR_tMRD +#define VC3_MPAR_ID VC3_MPAR__400_ns_dly +#define VC3_MPAR_SD VC3_MPAR_tXSRD +#define VC3_MPAR_OW (VC3_MPAR_WL-2) +#define VC3_MPAR_OR (VC3_MPAR_WL-3) +#define VC3_MPAR_RP (VC3_MPAR_bank_addr_cnt < 3 ? VC3_MPAR_tRP : VC3_MPAR_tRPA) +#define VC3_MPAR_FAW (VC3_MPAR_bank_addr_cnt < 3 ? 1 : VC3_MPAR_tFAW) +#define VC3_MPAR_BL (VC3_MPAR_BURST_LENGTH == 4 ? 2 : 4) +#define MSCC_MEMPARM_MR0 \ + (VC3_MPAR_BURST_LENGTH == 8 ? 3 : 2) | (VC3_MPAR_CL << 4) | ((VC3_MPAR_tWR-1) << 9) +#define MSCC_MEMPARM_MR1 0x382 /* DLL-on, Full-OD, AL=0, RTT=off, nDQS-on, RDQS-off, out-en */ +#define MSCC_MEMPARM_MR2 0 +#define MSCC_MEMPARM_MR3 0 +#else +#define VC3_MPAR_WL VC3_MPAR_CWL +#define VC3_MPAR_MD VC3_MPAR_tMOD +#define VC3_MPAR_ID VC3_MPAR_tXPR +#define VC3_MPAR_SD VC3_MPAR_tDLLK +#define VC3_MPAR_OW 2 +#define VC3_MPAR_OR 2 +#define VC3_MPAR_RP VC3_MPAR_tRP +#define VC3_MPAR_FAW VC3_MPAR_tFAW +#define VC3_MPAR_BL 4 +#define MSCC_MEMPARM_MR0 ((VC3_MPAR_RL - 4) << 4) | ((VC3_MPAR_tWR - 4) << 9) +#define MSCC_MEMPARM_MR1 0x0040 /* ODT_RTT: “0x0040” for 120ohm, and “0x0004” for 60ohm. */ +#define MSCC_MEMPARM_MR2 ((VC3_MPAR_WL - 5) << 3) +#define MSCC_MEMPARM_MR3 0 +#endif /* MIPS_VCOREIII_MEMORY_DDR3 */ + +#define MSCC_MEMPARM_MEMCFG \ + ((MIPS_VCOREIII_DDR_SIZE > SZ_512M) ? \ + ICPU_MEMCTRL_CFG_DDR_512MBYTE_PLUS : 0) | \ + (VC3_MPAR_16BIT ? ICPU_MEMCTRL_CFG_DDR_WIDTH : 0) | \ + (VC3_MPAR_DDR3_MODE ? ICPU_MEMCTRL_CFG_DDR_MODE : 0) | \ + (VC3_MPAR_BURST_SIZE ? ICPU_MEMCTRL_CFG_BURST_SIZE : 0) | \ + (VC3_MPAR_BURST_LENGTH == 8 ? ICPU_MEMCTRL_CFG_BURST_LEN : 0) | \ + (VC3_MPAR_bank_addr_cnt == 3 ? ICPU_MEMCTRL_CFG_BANK_CNT : 0) | \ + ICPU_MEMCTRL_CFG_MSB_ROW_ADDR(VC3_MPAR_row_addr_cnt-1) | \ + ICPU_MEMCTRL_CFG_MSB_COL_ADDR(VC3_MPAR_col_addr_cnt-1) + +#define MSCC_MEMPARM_PERIOD \ + ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF(8) | \ + ICPU_MEMCTRL_REF_PERIOD_REF_PERIOD(VC3_MPAR_tREFI) + +#ifdef CONFIG_SOC_OCELOT +#define MSCC_MEMPARM_TIMING0 \ + ICPU_MEMCTRL_TIMING0_RD_TO_WR_DLY(VC3_MPAR_RL+VC3_MPAR_BL+1-VC3_MPAR_WL) | \ + ICPU_MEMCTRL_TIMING0_WR_CS_CHANGE_DLY(VC3_MPAR_BL-1) | \ + ICPU_MEMCTRL_TIMING0_RD_CS_CHANGE_DLY(VC3_MPAR_BL) | \ + ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY(VC3_MPAR_tRAS_min-1) | \ + ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY(VC3_MPAR_WL + \ + VC3_MPAR_BL + \ + VC3_MPAR_tWR - 1) | \ + ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY(VC3_MPAR_BL-1) | \ + ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY(VC3_MPAR_WL-1) | \ + ICPU_MEMCTRL_TIMING0_RD_DATA_XFR_DLY(VC3_MPAR_RL-3) + +#define MSCC_MEMPARM_TIMING1 \ + ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY(VC3_MPAR_tRC-1) | \ + ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY(VC3_MPAR_FAW-1) | \ + ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY(VC3_MPAR_RP-1) | \ + ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY(VC3_MPAR_tRRD-1) | \ + ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY(VC3_MPAR_tRCD-1) | \ + ICPU_MEMCTRL_TIMING1_WR_TO_RD_DLY(VC3_MPAR_WL + \ + VC3_MPAR_BL + \ + VC3_MPAR_tWTR - 1) + +#define MSCC_MEMPARM_TIMING2 \ + ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY(VC3_MPAR_RP-1) | \ + ICPU_MEMCTRL_TIMING2_MDSET_DLY(VC3_MPAR_MD-1) | \ + ICPU_MEMCTRL_TIMING2_REF_DLY(VC3_MPAR_tRFC-1) | \ + ICPU_MEMCTRL_TIMING2_INIT_DLY(VC3_MPAR_ID-1) + +#define MSCC_MEMPARM_TIMING3 \ + ICPU_MEMCTRL_TIMING3_WR_TO_RD_CS_CHANGE_DLY(VC3_MPAR_WL + VC3_MPAR_tWTR - 1) | \ + ICPU_MEMCTRL_TIMING3_ODT_RD_DLY(VC3_MPAR_OR-1) | \ + ICPU_MEMCTRL_TIMING3_ODT_WR_DLY(VC3_MPAR_OW-1) | \ + ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY(VC3_MPAR_RL-3) + +#else +#define MSCC_MEMPARM_TIMING0 \ + ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY(VC3_MPAR_tRAS_min-1) | \ + ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY(VC3_MPAR_CL + \ + (VC3_MPAR_BURST_LENGTH == 8 ? 2 : 0) + \ + VC3_MPAR_tWR) | \ + ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY(VC3_MPAR_BURST_LENGTH == 8 ? 3 : 1) | \ + ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY(VC3_MPAR_CL-3) | \ + ICPU_MEMCTRL_TIMING0_RD_DATA_XFR_DLY(VC3_MPAR_CL-3) + +#define MSCC_MEMPARM_TIMING1 \ + ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY(VC3_MPAR_tRC-1) | \ + ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY(VC3_MPAR_tFAW) | \ + ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY(VC3_MPAR_tRP-1) | \ + ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY(VC3_MPAR_tRRD-1) | \ + ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY(VC3_MPAR_tRCD-1) | \ + ICPU_MEMCTRL_TIMING1_WR_TO_RD_DLY(VC3_MPAR_CL + \ + (VC3_MPAR_BURST_LENGTH == 8 ? 2 : 0) + \ + VC3_MPAR_tWTR) +#define MSCC_MEMPARM_TIMING2 \ + ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY(VC3_MPAR_tRPA-1) | \ + ICPU_MEMCTRL_TIMING2_MDSET_DLY(VC3_MPAR_tMRD-1) | \ + ICPU_MEMCTRL_TIMING2_REF_DLY(VC3_MPAR_tRFC-1) | \ + ICPU_MEMCTRL_TIMING2_FOUR_HUNDRED_NS_DLY(VC3_MPAR__400_ns_dly) + +#define MSCC_MEMPARM_TIMING3 \ + ICPU_MEMCTRL_TIMING3_WR_TO_RD_CS_CHANGE_DLY(VC3_MPAR_CL-1) | \ + ICPU_MEMCTRL_TIMING3_ODT_WR_DLY(VC3_MPAR_CL-1) | \ + ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY(VC3_MPAR_CL-3) + +#endif + +enum { + DDR_TRAIN_OK, + DDR_TRAIN_CONTINUE, + DDR_TRAIN_ERROR, +}; + +/* We actually have very few 'pause' possibilities apart from + * these assembly nops (at this very early stage). */ +#define PAUSE() asm volatile("nop; nop; nop; nop; nop; nop; nop; nop") + + +/* NB: Assumes inlining as no stack is available! */ +static inline void set_dly(u32 bytelane, u32 dly) +{ + register u32 r = readl(REG_CFG(ICPU_MEMCTRL_DQS_DLY(bytelane))); + r &= ~ICPU_MEMCTRL_DQS_DLY_DQS_DLY_M; + r |= ICPU_MEMCTRL_DQS_DLY_DQS_DLY(dly); + writel(r, REG_CFG(ICPU_MEMCTRL_DQS_DLY(bytelane))); +} + +static inline bool incr_dly(u32 bytelane) +{ + register u32 r = readl(REG_CFG(ICPU_MEMCTRL_DQS_DLY(bytelane))); + if (ICPU_MEMCTRL_DQS_DLY_DQS_DLY(r) < 31) { + writel(r + 1, REG_CFG(ICPU_MEMCTRL_DQS_DLY(bytelane))); + return true; + } + + return false; +} +static inline bool adjust_dly(int adjust) +{ + register u32 r = readl(REG_CFG(ICPU_MEMCTRL_DQS_DLY(0))); + if (ICPU_MEMCTRL_DQS_DLY_DQS_DLY(r) < 31) { + writel(r + adjust, REG_CFG(ICPU_MEMCTRL_DQS_DLY(0))); + return true; + } + + return false; +} + +/* NB: Assumes inlining as no stack is available! */ +static inline void center_dly(u32 bytelane, u32 start) +{ + register u32 r = readl(REG_CFG(ICPU_MEMCTRL_DQS_DLY(bytelane))) - start; + writel(start + (r >> 1), REG_CFG(ICPU_MEMCTRL_DQS_DLY(bytelane))); +} + +static inline void memphy_soft_reset(void) +{ + writel(readl(REG_CFG(ICPU_MEMPHY_CFG)) | ICPU_MEMPHY_CFG_PHY_FIFO_RST, + REG_CFG(ICPU_MEMPHY_CFG)); + PAUSE(); + writel(readl(REG_CFG(ICPU_MEMPHY_CFG)) & ~ICPU_MEMPHY_CFG_PHY_FIFO_RST, + REG_CFG(ICPU_MEMPHY_CFG)); + PAUSE(); +} +#ifdef CONFIG_SOC_OCELOT +static u8 training_data[] = { 0xfe, 0x11, 0x33, 0x55, 0x77, 0x99, 0xbb, 0xdd }; + +static inline void sleep_100ns(u32 val) +{ + /* Set the timer tick generator to 100 ns */ + writel(VCOREIII_TIMER_DIVIDER-1, REG_CFG(ICPU_TIMER_TICK_DIV)); + + /* Set the timer value */ + writel(val, REG_CFG(ICPU_TIMER_VALUE(0))); + + /* Enable timer 0 for one-shot */ + writel(ICPU_TIMER_CTRL_ONE_SHOT_ENA | ICPU_TIMER_CTRL_TIMER_ENA, + REG_CFG(ICPU_TIMER_CTRL(0))); + + /* Wait for timer 0 to reach 0 */ + while (readl(REG_CFG(ICPU_TIMER_VALUE(0))) != 0) + ; +} + +static inline void hal_vcoreiii_ddr_reset_assert(void) +{ + /* DDR has reset pin on GPIO 19 toggle Low-High to release */ + writel(readl(REG_GCB(PERF_GPIO_OE)) | BIT(19), REG_GCB(PERF_GPIO_OE)); + writel(BIT(19), REG_GCB(PERF_GPIO_OUT_CLR)); + sleep_100ns(10000); +} + +static inline void hal_vcoreiii_ddr_reset_release(void) +{ + /* DDR has reset pin on GPIO 19 toggle Low-High to release */ + writel(readl(REG_GCB(PERF_GPIO_OE)) | BIT(19), REG_GCB(PERF_GPIO_OE)); + writel(BIT(19), REG_GCB(PERF_GPIO_OUT_SET)); + sleep_100ns(10000); +} + +/* + * DDR memory sanity checking failed, tally and do hard reset + * + * NB: Assumes inlining as no stack is available! + */ +static inline void hal_vcoreiii_ddr_failed(void) +{ + register u32 reset; + + writel(readl(REG_CFG(ICPU_GPR(6))) + 1, REG_CFG(ICPU_GPR(6))); + + writel(readl(REG_GCB(PERF_GPIO_OE)) & ~BIT(19), + REG_GCB(PERF_GPIO_OE)); + + /* Jump to reset - does not return */ + reset = KSEG0ADDR(_machine_restart); + icache_lock((void*)reset, 128); // Reset while running from cache + asm volatile ("jr %0" : : "r" (reset)); + + while(1) + ; +} +/* + * DDR memory sanity checking done, possibly enable ECC. + * + * NB: Assumes inlining as no stack is available! + */ +static inline void hal_vcoreiii_ddr_verified(void) +{ +#ifdef MIPS_VCOREIII_MEMORY_ECC + /* Finally, enable ECC */ + u32 val = readl(REG_CFG(ICPU_MEMCTRL_CFG)); + + val |= ICPU_MEMCTRL_CFG_DDR_ECC_ERR_ENA; + val &= ~ICPU_MEMCTRL_CFG_BURST_SIZE; + + writel(val, REG_CFG(ICPU_MEMCTRL_CFG)); +#endif + + /* Reset Status register - sticky bits */ + writel(readl(REG_CFG(ICPU_MEMCTRL_STAT)), + REG_CFG(ICPU_MEMCTRL_STAT)); +} +/* NB: Assumes inlining as no stack is available! */ +static inline int look_for(u32 bytelane) +{ + register u32 i; + /* Reset FIFO in case any previous access failed */ + for (i = 0; i < sizeof(training_data); i++) { + register u32 byte; + memphy_soft_reset(); + /* Reset sticky bits */ + writel(readl(REG_CFG(ICPU_MEMCTRL_STAT)), REG_CFG(ICPU_MEMCTRL_STAT)); + /* Read data */ + byte = ((volatile u8 *) MSCC_DDR_TO)[bytelane + (i * 4)]; + if (readl(REG_CFG(ICPU_MEMCTRL_STAT)) & + (ICPU_MEMCTRL_STAT_RDATA_MASKED| + ICPU_MEMCTRL_STAT_RDATA_DUMMY)) { + /* Noise on the line */ + goto read_error; + } + /* If mismatch, increment DQS - if possible */ + if (byte != training_data[i]) { + read_error: + if (!incr_dly(bytelane)) { + return DDR_TRAIN_ERROR; + } + return DDR_TRAIN_CONTINUE; + } + } + return DDR_TRAIN_OK; +} + + +/* NB: Assumes inlining as no stack is available! */ +static inline int look_past(u32 bytelane) +{ + register u32 i; + /* Reset FIFO in case any previous access failed */ + for (i = 0; i < sizeof(training_data); i++) { + register u32 byte; + memphy_soft_reset(); + /* Ack sticky bits */ + writel(readl(REG_CFG(ICPU_MEMCTRL_STAT)), REG_CFG(ICPU_MEMCTRL_STAT)); + byte = ((volatile u8 *) MSCC_DDR_TO)[bytelane + (i * 4)]; + if (readl(REG_CFG(ICPU_MEMCTRL_STAT)) & + (ICPU_MEMCTRL_STAT_RDATA_MASKED| + ICPU_MEMCTRL_STAT_RDATA_DUMMY)) { + /* Noise on the line */ + goto read_error; + } + /* Bail out when we see first mismatch */ + if (byte != training_data[i]) { + read_error: + return DDR_TRAIN_OK; + } + } + /* All data compares OK, increase DQS and retry */ + if (!incr_dly(bytelane)) + return DDR_TRAIN_ERROR; + + return DDR_TRAIN_CONTINUE; +} + +static inline int hal_vcoreiii_train_bytelane(u32 bytelane) +{ + register int res; + register u32 dqs_s; + + set_dly(bytelane, 0); // Start training at DQS=0 + while ((res = look_for(bytelane)) == DDR_TRAIN_CONTINUE) + ; + if(res != DDR_TRAIN_OK) + return res; + + dqs_s = readl(REG_CFG(ICPU_MEMCTRL_DQS_DLY(bytelane))); + while ((res = look_past(bytelane)) == DDR_TRAIN_CONTINUE) + ; + if(res != DDR_TRAIN_OK) + return res; + /* Reset FIFO - for good measure */ + memphy_soft_reset(); + /* Adjust to center [dqs_s;cur] */ + center_dly(bytelane, dqs_s); + return DDR_TRAIN_OK; +} +/* This algorithm is converted from the TCL training algorithm used + * during silicon simulation. + * NB: Assumes inlining as no stack is available! + */ +static inline int hal_vcoreiii_init_dqs(void) +{ +#define MAX_DQS 32 + register u32 i, j; + for (i = 0; i < MAX_DQS; i++) { + set_dly(0, i); // Byte-lane 0 + for (j = 0; j < MAX_DQS; j++) { + register u32 __attribute__ ((unused)) byte; + set_dly(1, j); // Byte-lane 1 + /* Reset FIFO in case any previous access failed */ + memphy_soft_reset(); + writel(readl(REG_CFG(ICPU_MEMCTRL_STAT)), + REG_CFG(ICPU_MEMCTRL_STAT)); + byte = ((volatile u8 *) MSCC_DDR_TO)[0]; + byte = ((volatile u8 *) MSCC_DDR_TO)[1]; + if (readl(REG_CFG(ICPU_MEMCTRL_STAT)) & + (ICPU_MEMCTRL_STAT_RDATA_MASKED| + ICPU_MEMCTRL_STAT_RDATA_DUMMY)) { + } else { + return 0; + } + } + } + return -1; +} + + +static inline int dram_check(void) +{ +#define DDR ((volatile u32 *) MSCC_DDR_TO) + register u32 i; + + for (i = 0; i < 8; i++) { + DDR[i] = ~i; + if (DDR[i] != ~i) { + return 1; + } + } + return 0; +} +#else /* Luton */ + +static inline void sleep_100ns(u32 val) +{ +} +static inline void hal_vcoreiii_ddr_reset_assert(void) +{ +} +static inline void hal_vcoreiii_ddr_reset_release(void) +{ +} +static inline void hal_vcoreiii_ddr_failed(void) +{ + register u32 memphy_cfg = readl(REG_CFG(ICPU_MEMPHY_CFG)); + + /* Do a fifo reset and start over */ + writel( memphy_cfg | ICPU_MEMPHY_CFG_PHY_FIFO_RST, + REG_CFG(ICPU_MEMPHY_CFG)); + writel( memphy_cfg & ~ICPU_MEMPHY_CFG_PHY_FIFO_RST, + REG_CFG(ICPU_MEMPHY_CFG)); + writel( memphy_cfg | ICPU_MEMPHY_CFG_PHY_FIFO_RST, + REG_CFG(ICPU_MEMPHY_CFG)); +} + +static inline void hal_vcoreiii_ddr_verified(void){} + +static inline int look_for(u32 data) +{ + register u32 byte = ((volatile u8 *) MSCC_DDR_TO)[0]; + + if (data != byte) { + if (!incr_dly(0)) + return DDR_TRAIN_ERROR; + return DDR_TRAIN_CONTINUE; + } + + return DDR_TRAIN_OK; +} + +/* This algorithm is converted from the TCL training algorithm used + * during silicon simulation. + * NB: Assumes inlining as no stack is available! + */ +static inline int hal_vcoreiii_train_bytelane(u32 bytelane) +{ + register int res; + + set_dly(bytelane, 0); // Start training at DQS=0 + while ((res = look_for(0xff)) == DDR_TRAIN_CONTINUE) + ; + if(res != DDR_TRAIN_OK) + return res; + + set_dly(bytelane, 0); // Start training at DQS=0 + while ((res = look_for(0x00)) == DDR_TRAIN_CONTINUE) + ; + + if(res != DDR_TRAIN_OK) + return res; + + adjust_dly(-3); + + return DDR_TRAIN_OK; +} + +static inline int hal_vcoreiii_init_dqs(void) +{ + return 0; +} + +static inline int dram_check(void) +{ +#define DDR ((volatile u32 *) MSCC_DDR_TO) + register u32 i; + + for (i = 0; i < 8; i++) { + DDR[i] = ~i; + if (DDR[i] != ~i) { + return 1; + } + } + + return 0; +} +#endif + +/* NB: Called *early* to init memory controller - + * assumes inlining as no stack is available! */ +static inline void hal_vcoreiii_init_memctl(void) +{ + /* Ensure DDR is in reset */ + hal_vcoreiii_ddr_reset_assert(); + + /* Wait maybe not needed, but ... */ + PAUSE(); + + /* Drop sys ctl memory controller forced reset */ + writel(readl(REG_CFG(ICPU_RESET)) & ~ICPU_RESET_MEM_RST_FORCE, REG_CFG(ICPU_RESET)); + PAUSE(); + + /* Drop Reset, enable SSTL */ + writel(ICPU_MEMPHY_CFG_PHY_SSTL_ENA, REG_CFG(ICPU_MEMPHY_CFG)); + PAUSE(); + + /* Start the automatic SSTL output and ODT drive-strength calibration */ + writel(/* ODT */ + ICPU_MEMPHY_ZCAL_ZCAL_PROG_ODT(MIPS_VCOREIII_MEMORY_SSTL_ODT) | + /* drive strength */ + ICPU_MEMPHY_ZCAL_ZCAL_PROG(MIPS_VCOREIII_MEMORY_SSTL_DRIVE) | + /* Start calibration process */ + ICPU_MEMPHY_ZCAL_ZCAL_ENA, REG_CFG(ICPU_MEMPHY_ZCAL)); + + while(readl(REG_CFG(ICPU_MEMPHY_ZCAL)) & ICPU_MEMPHY_ZCAL_ZCAL_ENA) + ; /* Wait for ZCAL to clear */ +#ifdef CONFIG_SOC_OCELOT + /* Check no ZCAL_ERR */ + if (readl(REG_CFG(ICPU_MEMPHY_ZCAL_STAT)) & ICPU_MEMPHY_ZCAL_STAT_ZCAL_ERR) { + hal_vcoreiii_ddr_failed(); + } +#endif + /* Drive CL, CK, ODT */ + writel(readl(REG_CFG(ICPU_MEMPHY_CFG)) | + ICPU_MEMPHY_CFG_PHY_ODT_OE | + ICPU_MEMPHY_CFG_PHY_CK_OE | + ICPU_MEMPHY_CFG_PHY_CL_OE, REG_CFG(ICPU_MEMPHY_CFG)); + + /* Initialize memory controller */ + writel(MSCC_MEMPARM_MEMCFG, REG_CFG(ICPU_MEMCTRL_CFG)); + writel(MSCC_MEMPARM_PERIOD, REG_CFG(ICPU_MEMCTRL_REF_PERIOD)); + + writel(MSCC_MEMPARM_TIMING0, REG_CFG(ICPU_MEMCTRL_TIMING0)); + writel(MSCC_MEMPARM_TIMING1, REG_CFG(ICPU_MEMCTRL_TIMING1)); + writel(MSCC_MEMPARM_TIMING2, REG_CFG(ICPU_MEMCTRL_TIMING2)); + writel(MSCC_MEMPARM_TIMING3, REG_CFG(ICPU_MEMCTRL_TIMING3)); + writel(MSCC_MEMPARM_MR0, REG_CFG(ICPU_MEMCTRL_MR0_VAL)); + writel(MSCC_MEMPARM_MR1, REG_CFG(ICPU_MEMCTRL_MR1_VAL)); + writel(MSCC_MEMPARM_MR2, REG_CFG(ICPU_MEMCTRL_MR2_VAL)); + writel(MSCC_MEMPARM_MR3, REG_CFG(ICPU_MEMCTRL_MR3_VAL)); + +#ifdef CONFIG_SOC_OCELOT + /* Termination setup - enable ODT */ + writel(ICPU_MEMCTRL_TERMRES_CTRL_LOCAL_ODT_RD_ENA | + /* Assert ODT0 for any write */ + ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA(3), + REG_CFG(ICPU_MEMCTRL_TERMRES_CTRL)); + + /* Release Reset from DDR */ + hal_vcoreiii_ddr_reset_release(); + + writel(readl(REG_CFG(ICPU_GPR(7))) + 1, REG_CFG(ICPU_GPR(7))); +#else /* Luton */ + /* Termination setup - disable ODT */ + writel(0, REG_CFG(ICPU_MEMCTRL_TERMRES_CTRL)); + +#endif +} + +static void inline hal_vcoreiii_wait_memctl(void) +{ + /* Now, rip it! */ + writel(ICPU_MEMCTRL_CTRL_INITIALIZE, REG_CFG(ICPU_MEMCTRL_CTRL)); + + while(!(readl(REG_CFG(ICPU_MEMCTRL_STAT)) & ICPU_MEMCTRL_STAT_INIT_DONE)) + ; + + /* Settle...? */ + sleep_100ns(10000); +#ifdef CONFIG_SOC_OCELOT + /* Establish data contents in DDR RAM for training */ + ((volatile u32 *)MSCC_DDR_TO)[0] = 0xcacafefe; + ((volatile u32 *)MSCC_DDR_TO)[1] = 0x22221111; + ((volatile u32 *)MSCC_DDR_TO)[2] = 0x44443333; + ((volatile u32 *)MSCC_DDR_TO)[3] = 0x66665555; + ((volatile u32 *)MSCC_DDR_TO)[4] = 0x88887777; + ((volatile u32 *)MSCC_DDR_TO)[5] = 0xaaaa9999; + ((volatile u32 *)MSCC_DDR_TO)[6] = 0xccccbbbb; + ((volatile u32 *)MSCC_DDR_TO)[7] = 0xeeeedddd; +#else + ((volatile u32 *)MSCC_DDR_TO)[0] = 0xff; +#endif +} +#endif /* __ASM_MACH_DDR_H */ diff --git a/arch/mips/mach-mscc/include/mach/luton/luton.h b/arch/mips/mach-mscc/include/mach/luton/luton.h new file mode 100644 index 0000000000..4f761b1bb7 --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/luton/luton.h @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Microsemi Ocelot Switch driver + * + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef _MSCC_OCELOT_H_ +#define _MSCC_OCELOT_H_ + +#include <linux/bitops.h> +#include <dm.h> + +/* + * Target offset base(s) + */ +#define MSCC_IO_ORIGIN1_OFFSET 0x60000000 +#define MSCC_IO_ORIGIN1_SIZE 0x01000000 +#define MSCC_IO_ORIGIN2_OFFSET 0x70000000 +#define MSCC_IO_ORIGIN2_SIZE 0x00200000 +#ifndef MSCC_IO_OFFSET1 +#define MSCC_IO_OFFSET1(offset) (MSCC_IO_ORIGIN1_OFFSET + offset) +#endif +#ifndef MSCC_IO_OFFSET2 +#define MSCC_IO_OFFSET2(offset) (MSCC_IO_ORIGIN2_OFFSET + offset) +#endif +#define BASE_CFG 0x70000000 +#define BASE_UART 0x70100000 +#define BASE_DEVCPU_GCB 0x60070000 +#define BASE_MACRO 0x600a0000 + +#define REG_OFFSET(t, o) ((volatile unsigned long *)(t + (o))) +#define REG_CFG(x) REG_OFFSET(BASE_CFG, x) +#define REG_GCB(x) REG_OFFSET(BASE_DEVCPU_GCB, x) +#define REG_MACRO(x) REG_OFFSET(BASE_MACRO, x) + +#endif diff --git a/arch/mips/mach-mscc/include/mach/luton/luton_devcpu_gcb.h b/arch/mips/mach-mscc/include/mach/luton/luton_devcpu_gcb.h new file mode 100644 index 0000000000..0d80c8a534 --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/luton/luton_devcpu_gcb.h @@ -0,0 +1,16 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef _MSCC_OCELOT_DEVCPU_GCB_H_ +#define _MSCC_OCELOT_DEVCPU_GCB_H_ + +#define PERF_GPR 0x4 + +#define PERF_SOFT_RST 0x90 + +#define PERF_SOFT_RST_SOFT_SWC_RST BIT(1) +#define PERF_SOFT_RST_SOFT_CHIP_RST BIT(0) + +#endif diff --git a/arch/mips/mach-mscc/include/mach/luton/luton_icpu_cfg.h b/arch/mips/mach-mscc/include/mach/luton/luton_icpu_cfg.h new file mode 100644 index 0000000000..b0b09f4d21 --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/luton/luton_icpu_cfg.h @@ -0,0 +1,247 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef _MSCC_OCELOT_ICPU_CFG_H_ +#define _MSCC_OCELOT_ICPU_CFG_H_ + +#define ICPU_GPR(x) (0x4 * (x)) +#define ICPU_GPR_RSZ 0x4 + +#define ICPU_RESET 0x20 + +#define ICPU_RESET_CORE_RST_CPU_ONLY BIT(3) +#define ICPU_RESET_CORE_RST_PROTECT BIT(2) +#define ICPU_RESET_CORE_RST_FORCE BIT(1) +#define ICPU_RESET_MEM_RST_FORCE BIT(0) + +#define ICPU_GENERAL_CTRL 0x24 + +#define ICPU_GENERAL_CTRL_CPU_BUSIF_SLEEP_DIS BIT(14) +#define ICPU_GENERAL_CTRL_CPU_BUSIF_WERR_ENA BIT(13) +#define ICPU_GENERAL_CTRL_CPU_8051_IROM_ENA BIT(12) +#define ICPU_GENERAL_CTRL_CPU_MIPS_DIS BIT(11) +#define ICPU_GENERAL_CTRL_IF_MIIM_SLV_ADDR_SEL BIT(10) +#define ICPU_GENERAL_CTRL_IF_MIIM_SLV_ENA BIT(9) +#define ICPU_GENERAL_CTRL_IF_PI_SLV_DONEPOL BIT(8) +#define ICPU_GENERAL_CTRL_IF_PI_MST_ENA BIT(7) +#define ICPU_GENERAL_CTRL_IF_PI_SLV_ENA BIT(6) +#define ICPU_GENERAL_CTRL_IF_SI_OWNER(x) (((x) << 4) & GENMASK(5, 4)) +#define ICPU_GENERAL_CTRL_IF_SI_OWNER_M GENMASK(5, 4) +#define ICPU_GENERAL_CTRL_IF_SI_OWNER_X(x) (((x) & GENMASK(5, 4)) >> 4) +#define ICPU_GENERAL_CTRL_SSI_MST_CONTENTION BIT(3) +#define ICPU_GENERAL_CTRL_CPU_BE_ENA BIT(2) +#define ICPU_GENERAL_CTRL_CPU_DIS BIT(1) +#define ICPU_GENERAL_CTRL_BOOT_MODE_ENA BIT(0) + +#define ICPU_SPI_MST_CFG 0x3c + +#define ICPU_SPI_MST_CFG_A32B_ENA BIT(11) +#define ICPU_SPI_MST_CFG_FAST_READ_ENA BIT(10) +#define ICPU_SPI_MST_CFG_CS_DESELECT_TIME(x) (((x) << 5) & GENMASK(9, 5)) +#define ICPU_SPI_MST_CFG_CS_DESELECT_TIME_M GENMASK(9, 5) +#define ICPU_SPI_MST_CFG_CS_DESELECT_TIME_X(x) (((x) & GENMASK(9, 5)) >> 5) +#define ICPU_SPI_MST_CFG_CLK_DIV(x) ((x) & GENMASK(4, 0)) +#define ICPU_SPI_MST_CFG_CLK_DIV_M GENMASK(4, 0) + + +#define ICPU_SW_MODE 0x64 + +#define ICPU_SW_MODE_SW_PIN_CTRL_MODE BIT(13) +#define ICPU_SW_MODE_SW_SPI_SCK BIT(12) +#define ICPU_SW_MODE_SW_SPI_SCK_OE BIT(11) +#define ICPU_SW_MODE_SW_SPI_SDO BIT(10) +#define ICPU_SW_MODE_SW_SPI_SDO_OE BIT(9) +#define ICPU_SW_MODE_SW_SPI_CS(x) (((x) << 5) & GENMASK(8, 5)) +#define ICPU_SW_MODE_SW_SPI_CS_M GENMASK(8, 5) +#define ICPU_SW_MODE_SW_SPI_CS_X(x) (((x) & GENMASK(8, 5)) >> 5) +#define ICPU_SW_MODE_SW_SPI_CS_OE(x) (((x) << 1) & GENMASK(4, 1)) +#define ICPU_SW_MODE_SW_SPI_CS_OE_M GENMASK(4, 1) +#define ICPU_SW_MODE_SW_SPI_CS_OE_X(x) (((x) & GENMASK(4, 1)) >> 1) +#define ICPU_SW_MODE_SW_SPI_SDI BIT(0) + +#define ICPU_INTR_ENA 0x88 + +#define ICPU_INTR_IRQ0_ENA 0x98 +#define ICPU_INTR_IRQ0_ENA_IRQ0_ENA BIT(0) + +#define ICPU_MEMCTRL_CTRL 0x234 + +#define ICPU_MEMCTRL_CTRL_PWR_DOWN BIT(3) +#define ICPU_MEMCTRL_CTRL_MDSET BIT(2) +#define ICPU_MEMCTRL_CTRL_STALL_REF_ENA BIT(1) +#define ICPU_MEMCTRL_CTRL_INITIALIZE BIT(0) + +#define ICPU_MEMCTRL_CFG 0x238 + +#define ICPU_MEMCTRL_CFG_DDR_512MBYTE_PLUS BIT(16) +#define ICPU_MEMCTRL_CFG_DDR_ECC_ERR_ENA BIT(15) +#define ICPU_MEMCTRL_CFG_DDR_ECC_COR_ENA BIT(14) +#define ICPU_MEMCTRL_CFG_DDR_ECC_ENA BIT(13) +#define ICPU_MEMCTRL_CFG_DDR_WIDTH BIT(12) +#define ICPU_MEMCTRL_CFG_DDR_MODE BIT(11) +#define ICPU_MEMCTRL_CFG_BURST_SIZE BIT(10) +#define ICPU_MEMCTRL_CFG_BURST_LEN BIT(9) +#define ICPU_MEMCTRL_CFG_BANK_CNT BIT(8) +#define ICPU_MEMCTRL_CFG_MSB_ROW_ADDR(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_CFG_MSB_ROW_ADDR_M GENMASK(7, 4) +#define ICPU_MEMCTRL_CFG_MSB_ROW_ADDR_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_CFG_MSB_COL_ADDR(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_CFG_MSB_COL_ADDR_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_STAT 0x23C + +#define ICPU_MEMCTRL_STAT_RDATA_MASKED BIT(5) +#define ICPU_MEMCTRL_STAT_RDATA_DUMMY BIT(4) +#define ICPU_MEMCTRL_STAT_RDATA_ECC_ERR BIT(3) +#define ICPU_MEMCTRL_STAT_RDATA_ECC_COR BIT(2) +#define ICPU_MEMCTRL_STAT_PWR_DOWN_ACK BIT(1) +#define ICPU_MEMCTRL_STAT_INIT_DONE BIT(0) + +#define ICPU_MEMCTRL_REF_PERIOD 0x240 + +#define ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF(x) (((x) << 16) & GENMASK(19, 16)) +#define ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF_M GENMASK(19, 16) +#define ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF_X(x) (((x) & GENMASK(19, 16)) >> 16) +#define ICPU_MEMCTRL_REF_PERIOD_REF_PERIOD(x) ((x) & GENMASK(15, 0)) +#define ICPU_MEMCTRL_REF_PERIOD_REF_PERIOD_M GENMASK(15, 0) + +#define ICPU_MEMCTRL_TIMING0 0x248 + +#define ICPU_MEMCTRL_TIMING0_RD_TO_WR_DLY(x) (((x) << 28) & GENMASK(31, 28)) +#define ICPU_MEMCTRL_TIMING0_RD_TO_WR_DLY_M GENMASK(31, 28) +#define ICPU_MEMCTRL_TIMING0_RD_TO_WR_DLY_X(x) (((x) & GENMASK(31, 28)) >> 28) +#define ICPU_MEMCTRL_TIMING0_WR_CS_CHANGE_DLY(x) (((x) << 24) & GENMASK(27, 24)) +#define ICPU_MEMCTRL_TIMING0_WR_CS_CHANGE_DLY_M GENMASK(27, 24) +#define ICPU_MEMCTRL_TIMING0_WR_CS_CHANGE_DLY_X(x) (((x) & GENMASK(27, 24)) >> 24) +#define ICPU_MEMCTRL_TIMING0_RD_CS_CHANGE_DLY(x) (((x) << 20) & GENMASK(23, 20)) +#define ICPU_MEMCTRL_TIMING0_RD_CS_CHANGE_DLY_M GENMASK(23, 20) +#define ICPU_MEMCTRL_TIMING0_RD_CS_CHANGE_DLY_X(x) (((x) & GENMASK(23, 20)) >> 20) +#define ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY(x) (((x) << 16) & GENMASK(19, 16)) +#define ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY_M GENMASK(19, 16) +#define ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY_X(x) (((x) & GENMASK(19, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY(x) (((x) << 12) & GENMASK(15, 12)) +#define ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY_M GENMASK(15, 12) +#define ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY_X(x) (((x) & GENMASK(15, 12)) >> 12) +#define ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY(x) (((x) << 8) & GENMASK(11, 8)) +#define ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY_M GENMASK(11, 8) +#define ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY_X(x) (((x) & GENMASK(11, 8)) >> 8) +#define ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY_M GENMASK(7, 4) +#define ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_TIMING0_RD_DATA_XFR_DLY(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_TIMING0_RD_DATA_XFR_DLY_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_TIMING1 0x24c + +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY(x) (((x) << 24) & GENMASK(31, 24)) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY_M GENMASK(31, 24) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY_X(x) (((x) & GENMASK(31, 24)) >> 24) +#define ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY(x) (((x) << 16) & GENMASK(23, 16)) +#define ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY_M GENMASK(23, 16) +#define ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY_X(x) (((x) & GENMASK(23, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY(x) (((x) << 12) & GENMASK(15, 12)) +#define ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY_M GENMASK(15, 12) +#define ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY_X(x) (((x) & GENMASK(15, 12)) >> 12) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY(x) (((x) << 8) & GENMASK(11, 8)) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY_M GENMASK(11, 8) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY_X(x) (((x) & GENMASK(11, 8)) >> 8) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY_M GENMASK(7, 4) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_TIMING1_WR_TO_RD_DLY(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_TIMING1_WR_TO_RD_DLY_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_TIMING2 0x250 + +#define ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY(x) (((x) << 28) & GENMASK(31, 28)) +#define ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY_M GENMASK(31, 28) +#define ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY_X(x) (((x) & GENMASK(31, 28)) >> 28) +#define ICPU_MEMCTRL_TIMING2_MDSET_DLY(x) (((x) << 24) & GENMASK(27, 24)) +#define ICPU_MEMCTRL_TIMING2_MDSET_DLY_M GENMASK(27, 24) +#define ICPU_MEMCTRL_TIMING2_MDSET_DLY_X(x) (((x) & GENMASK(27, 24)) >> 24) +#define ICPU_MEMCTRL_TIMING2_REF_DLY(x) (((x) << 16) & GENMASK(23, 16)) +#define ICPU_MEMCTRL_TIMING2_REF_DLY_M GENMASK(23, 16) +#define ICPU_MEMCTRL_TIMING2_REF_DLY_X(x) (((x) & GENMASK(23, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING2_FOUR_HUNDRED_NS_DLY(x) ((x) & GENMASK(15, 0)) +#define ICPU_MEMCTRL_TIMING2_FOUR_HUNDRED_NS_DLY_M GENMASK(15, 0) + +#define ICPU_MEMCTRL_TIMING3 0x254 + +#define ICPU_MEMCTRL_TIMING3_RMW_DLY(x) (((x) << 16) & GENMASK(19, 16)) +#define ICPU_MEMCTRL_TIMING3_RMW_DLY_M GENMASK(19, 16) +#define ICPU_MEMCTRL_TIMING3_RMW_DLY_X(x) (((x) & GENMASK(19, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING3_ODT_RD_DLY(x) (((x) << 12) & GENMASK(15, 12)) +#define ICPU_MEMCTRL_TIMING3_ODT_RD_DLY_M GENMASK(15, 12) +#define ICPU_MEMCTRL_TIMING3_ODT_RD_DLY_X(x) (((x) & GENMASK(15, 12)) >> 12) +#define ICPU_MEMCTRL_TIMING3_ODT_WR_DLY(x) (((x) << 8) & GENMASK(11, 8)) +#define ICPU_MEMCTRL_TIMING3_ODT_WR_DLY_M GENMASK(11, 8) +#define ICPU_MEMCTRL_TIMING3_ODT_WR_DLY_X(x) (((x) & GENMASK(11, 8)) >> 8) +#define ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY_M GENMASK(7, 4) +#define ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_TIMING3_WR_TO_RD_CS_CHANGE_DLY(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_TIMING3_WR_TO_RD_CS_CHANGE_DLY_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_MR0_VAL 0x258 + +#define ICPU_MEMCTRL_MR1_VAL 0x25c + +#define ICPU_MEMCTRL_MR2_VAL 0x260 + +#define ICPU_MEMCTRL_MR3_VAL 0x264 + +#define ICPU_MEMCTRL_TERMRES_CTRL 0x268 + +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_EXT BIT(11) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_ENA(x) (((x) << 7) & GENMASK(10, 7)) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_ENA_M GENMASK(10, 7) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_ENA_X(x) (((x) & GENMASK(10, 7)) >> 7) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_EXT BIT(6) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA(x) (((x) << 2) & GENMASK(5, 2)) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA_M GENMASK(5, 2) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA_X(x) (((x) & GENMASK(5, 2)) >> 2) +#define ICPU_MEMCTRL_TERMRES_CTRL_LOCAL_ODT_RD_EXT BIT(1) +#define ICPU_MEMCTRL_TERMRES_CTRL_LOCAL_ODT_RD_ENA BIT(0) + +#define ICPU_MEMCTRL_DQS_DLY(x) (0x270) + +#define ICPU_MEMCTRL_DQS_DLY_TRAIN_DQ_ENA BIT(11) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM1(x) (((x) << 8) & GENMASK(10, 8)) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM1_M GENMASK(10, 8) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM1_X(x) (((x) & GENMASK(10, 8)) >> 8) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM0(x) (((x) << 5) & GENMASK(7, 5)) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM0_M GENMASK(7, 5) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM0_X(x) (((x) & GENMASK(7, 5)) >> 5) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY(x) ((x) & GENMASK(4, 0)) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_M GENMASK(4, 0) + +#define ICPU_MEMPHY_CFG 0x278 + +#define ICPU_MEMPHY_CFG_PHY_FLUSH_DIS BIT(10) +#define ICPU_MEMPHY_CFG_PHY_RD_ADJ_DIS BIT(9) +#define ICPU_MEMPHY_CFG_PHY_DQS_EXT BIT(8) +#define ICPU_MEMPHY_CFG_PHY_FIFO_RST BIT(7) +#define ICPU_MEMPHY_CFG_PHY_DLL_BL_RST BIT(6) +#define ICPU_MEMPHY_CFG_PHY_DLL_CL_RST BIT(5) +#define ICPU_MEMPHY_CFG_PHY_ODT_OE BIT(4) +#define ICPU_MEMPHY_CFG_PHY_CK_OE BIT(3) +#define ICPU_MEMPHY_CFG_PHY_CL_OE BIT(2) +#define ICPU_MEMPHY_CFG_PHY_SSTL_ENA BIT(1) +#define ICPU_MEMPHY_CFG_PHY_RST BIT(0) +#define ICPU_MEMPHY_DQ_DLY_TRM 0x180 +#define ICPU_MEMPHY_DQ_DLY_TRM_RSZ 0x4 + +#define ICPU_MEMPHY_ZCAL 0x294 + +#define ICPU_MEMPHY_ZCAL_ZCAL_CLK_SEL BIT(9) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_ODT(x) (((x) << 5) & GENMASK(8, 5)) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_ODT_M GENMASK(8, 5) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_ODT_X(x) (((x) & GENMASK(8, 5)) >> 5) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG(x) (((x) << 1) & GENMASK(4, 1)) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_M GENMASK(4, 1) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_X(x) (((x) & GENMASK(4, 1)) >> 1) +#define ICPU_MEMPHY_ZCAL_ZCAL_ENA BIT(0) + +#endif diff --git a/arch/mips/mach-mscc/include/mach/ocelot/ocelot.h b/arch/mips/mach-mscc/include/mach/ocelot/ocelot.h new file mode 100644 index 0000000000..698e6808a4 --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/ocelot/ocelot.h @@ -0,0 +1,35 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Microsemi Ocelot Switch driver + * + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef _MSCC_OCELOT_H_ +#define _MSCC_OCELOT_H_ + +#include <linux/bitops.h> +#include <dm.h> + +/* + * Target offset base(s) + */ +#define MSCC_IO_ORIGIN1_OFFSET 0x70000000 +#define MSCC_IO_ORIGIN1_SIZE 0x00200000 +#define MSCC_IO_ORIGIN2_OFFSET 0x71000000 +#define MSCC_IO_ORIGIN2_SIZE 0x01000000 +#ifndef MSCC_IO_OFFSET1 +#define MSCC_IO_OFFSET1(offset) (MSCC_IO_ORIGIN1_OFFSET + offset) +#endif +#ifndef MSCC_IO_OFFSET2 +#define MSCC_IO_OFFSET2(offset) (MSCC_IO_ORIGIN2_OFFSET + offset) +#endif +#define BASE_CFG 0x70000000 +#define BASE_UART 0x70100000 +#define BASE_DEVCPU_GCB 0x71070000 + +#define REG_OFFSET(t, o) ((volatile unsigned long *)(t + (o))) +#define REG_CFG(x) REG_OFFSET(BASE_CFG, x) +#define REG_GCB(x) REG_OFFSET(BASE_DEVCPU_GCB, x) + +#endif diff --git a/arch/mips/mach-mscc/include/mach/ocelot/ocelot_devcpu_gcb.h b/arch/mips/mach-mscc/include/mach/ocelot/ocelot_devcpu_gcb.h new file mode 100644 index 0000000000..4bcd0b3c8c --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/ocelot/ocelot_devcpu_gcb.h @@ -0,0 +1,49 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef _MSCC_OCELOT_DEVCPU_GCB_H_ +#define _MSCC_OCELOT_DEVCPU_GCB_H_ + + +#define PERF_GPR 0x4 + +#define PERF_SOFT_RST 0x8 + +#define PERF_SOFT_RST_SOFT_NON_CFG_RST BIT(2) +#define PERF_SOFT_RST_SOFT_SWC_RST BIT(1) +#define PERF_SOFT_RST_SOFT_CHIP_RST BIT(0) + +#define PERF_FEA_STAT 0x14 + +#define PERF_FEA_DIS 0x18 + +#define PERF_SW_INTR 0x1c + +#define PERF_SW_INTR_SW1_INTR BIT(1) +#define PERF_SW_INTR_SW0_INTR BIT(0) + +#define PERF_GPIO_OUT_SET 0x34 + +#define PERF_GPIO_OUT_CLR 0x38 + +#define PERF_GPIO_OUT 0x3c + +#define PERF_GPIO_IN 0x40 + +#define PERF_GPIO_OE 0x44 + +#define PERF_GPIO_INTR 0x48 + +#define PERF_GPIO_INTR_ENA 0x4c + +#define PERF_GPIO_INTR_IDENT 0x50 + +#define PERF_GPIO_ALT(x) (0x54 + 4 * (x)) +#define PERF_GPIO_ALT_RSZ 0x4 + +#define PERF_GPIO_SD_MAP 0x5c +#define PERF_GPIO_SD_MAP_RSZ 0x4 + +#endif diff --git a/arch/mips/mach-mscc/include/mach/ocelot/ocelot_icpu_cfg.h b/arch/mips/mach-mscc/include/mach/ocelot/ocelot_icpu_cfg.h new file mode 100644 index 0000000000..6c354bc475 --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/ocelot/ocelot_icpu_cfg.h @@ -0,0 +1,278 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef _MSCC_OCELOT_ICPU_CFG_H_ +#define _MSCC_OCELOT_ICPU_CFG_H_ + +#define ICPU_GPR(x) (0x4 * (x)) +#define ICPU_GPR_RSZ 0x4 + +#define ICPU_RESET 0x20 + +#define ICPU_RESET_CORE_RST_CPU_ONLY BIT(3) +#define ICPU_RESET_CORE_RST_PROTECT BIT(2) +#define ICPU_RESET_CORE_RST_FORCE BIT(1) +#define ICPU_RESET_MEM_RST_FORCE BIT(0) + +#define ICPU_GENERAL_CTRL 0x24 + +#define ICPU_GENERAL_CTRL_CPU_BUSIF_SLEEP_DIS BIT(14) +#define ICPU_GENERAL_CTRL_CPU_BUSIF_WERR_ENA BIT(13) +#define ICPU_GENERAL_CTRL_CPU_8051_IROM_ENA BIT(12) +#define ICPU_GENERAL_CTRL_CPU_MIPS_DIS BIT(11) +#define ICPU_GENERAL_CTRL_IF_MIIM_SLV_ADDR_SEL BIT(10) +#define ICPU_GENERAL_CTRL_IF_MIIM_SLV_ENA BIT(9) +#define ICPU_GENERAL_CTRL_IF_PI_SLV_DONEPOL BIT(8) +#define ICPU_GENERAL_CTRL_IF_PI_MST_ENA BIT(7) +#define ICPU_GENERAL_CTRL_IF_PI_SLV_ENA BIT(6) +#define ICPU_GENERAL_CTRL_IF_SI_OWNER(x) (((x) << 4) & GENMASK(5, 4)) +#define ICPU_GENERAL_CTRL_IF_SI_OWNER_M GENMASK(5, 4) +#define ICPU_GENERAL_CTRL_IF_SI_OWNER_X(x) (((x) & GENMASK(5, 4)) >> 4) +#define ICPU_GENERAL_CTRL_SSI_MST_CONTENTION BIT(3) +#define ICPU_GENERAL_CTRL_CPU_BE_ENA BIT(2) +#define ICPU_GENERAL_CTRL_CPU_DIS BIT(1) +#define ICPU_GENERAL_CTRL_BOOT_MODE_ENA BIT(0) +#define ICPU_SPI_MST_CFG 0x3c + +#define ICPU_SPI_MST_CFG_A32B_ENA BIT(11) +#define ICPU_SPI_MST_CFG_FAST_READ_ENA BIT(10) +#define ICPU_SPI_MST_CFG_CS_DESELECT_TIME(x) (((x) << 5) & GENMASK(9, 5)) +#define ICPU_SPI_MST_CFG_CS_DESELECT_TIME_M GENMASK(9, 5) +#define ICPU_SPI_MST_CFG_CS_DESELECT_TIME_X(x) (((x) & GENMASK(9, 5)) >> 5) +#define ICPU_SPI_MST_CFG_CLK_DIV(x) ((x) & GENMASK(4, 0)) +#define ICPU_SPI_MST_CFG_CLK_DIV_M GENMASK(4, 0) + +#define ICPU_SW_MODE 0x50 + +#define ICPU_SW_MODE_SW_PIN_CTRL_MODE BIT(13) +#define ICPU_SW_MODE_SW_SPI_SCK BIT(12) +#define ICPU_SW_MODE_SW_SPI_SCK_OE BIT(11) +#define ICPU_SW_MODE_SW_SPI_SDO BIT(10) +#define ICPU_SW_MODE_SW_SPI_SDO_OE BIT(9) +#define ICPU_SW_MODE_SW_SPI_CS(x) (((x) << 5) & GENMASK(8, 5)) +#define ICPU_SW_MODE_SW_SPI_CS_M GENMASK(8, 5) +#define ICPU_SW_MODE_SW_SPI_CS_X(x) (((x) & GENMASK(8, 5)) >> 5) +#define ICPU_SW_MODE_SW_SPI_CS_OE(x) (((x) << 1) & GENMASK(4, 1)) +#define ICPU_SW_MODE_SW_SPI_CS_OE_M GENMASK(4, 1) +#define ICPU_SW_MODE_SW_SPI_CS_OE_X(x) (((x) & GENMASK(4, 1)) >> 1) +#define ICPU_SW_MODE_SW_SPI_SDI BIT(0) + +#define ICPU_INTR_ENA 0x88 + +#define ICPU_DST_INTR_MAP(x) (0x98 + 0x4 * (x)) +#define ICPU_DST_INTR_MAP_RSZ 0x4 + +#define ICPU_DST_INTR_IDENT 0xa8 +#define ICPU_DST_INTR_IDENT_RSZ 0x4 + +#define ICPU_TIMER_TICK_DIV 0xe8 +#define ICPU_TIMER_VALUE(x) (0xec + 0x4 * (x)) + +#define ICPU_TIMER_CTRL(x) (0x104 + 0x4 * (x)) +#define ICPU_TIMER_CTRL_MAX_FREQ_ENA BIT(3) +#define ICPU_TIMER_CTRL_ONE_SHOT_ENA BIT(2) +#define ICPU_TIMER_CTRL_TIMER_ENA BIT(1) +#define ICPU_TIMER_CTRL_FORCE_RELOAD BIT(0) + +#define ICPU_MEMCTRL_CTRL 0x110 +#define ICPU_MEMCTRL_CTRL_PWR_DOWN BIT(3) +#define ICPU_MEMCTRL_CTRL_MDSET BIT(2) +#define ICPU_MEMCTRL_CTRL_STALL_REF_ENA BIT(1) +#define ICPU_MEMCTRL_CTRL_INITIALIZE BIT(0) + +#define ICPU_MEMCTRL_CFG 0x114 + +#define ICPU_MEMCTRL_CFG_DDR_512MBYTE_PLUS BIT(16) +#define ICPU_MEMCTRL_CFG_DDR_ECC_ERR_ENA BIT(15) +#define ICPU_MEMCTRL_CFG_DDR_ECC_COR_ENA BIT(14) +#define ICPU_MEMCTRL_CFG_DDR_ECC_ENA BIT(13) +#define ICPU_MEMCTRL_CFG_DDR_WIDTH BIT(12) +#define ICPU_MEMCTRL_CFG_DDR_MODE BIT(11) +#define ICPU_MEMCTRL_CFG_BURST_SIZE BIT(10) +#define ICPU_MEMCTRL_CFG_BURST_LEN BIT(9) +#define ICPU_MEMCTRL_CFG_BANK_CNT BIT(8) +#define ICPU_MEMCTRL_CFG_MSB_ROW_ADDR(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_CFG_MSB_ROW_ADDR_M GENMASK(7, 4) +#define ICPU_MEMCTRL_CFG_MSB_ROW_ADDR_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_CFG_MSB_COL_ADDR(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_CFG_MSB_COL_ADDR_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_STAT 0x118 + +#define ICPU_MEMCTRL_STAT_RDATA_MASKED BIT(5) +#define ICPU_MEMCTRL_STAT_RDATA_DUMMY BIT(4) +#define ICPU_MEMCTRL_STAT_RDATA_ECC_ERR BIT(3) +#define ICPU_MEMCTRL_STAT_RDATA_ECC_COR BIT(2) +#define ICPU_MEMCTRL_STAT_PWR_DOWN_ACK BIT(1) +#define ICPU_MEMCTRL_STAT_INIT_DONE BIT(0) + +#define ICPU_MEMCTRL_REF_PERIOD 0x11c + +#define ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF(x) (((x) << 16) & GENMASK(19, 16)) +#define ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF_M GENMASK(19, 16) +#define ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF_X(x) (((x) & GENMASK(19, 16)) >> 16) +#define ICPU_MEMCTRL_REF_PERIOD_REF_PERIOD(x) ((x) & GENMASK(15, 0)) +#define ICPU_MEMCTRL_REF_PERIOD_REF_PERIOD_M GENMASK(15, 0) + +#define ICPU_MEMCTRL_TIMING0 0x124 + +#define ICPU_MEMCTRL_TIMING0_RD_TO_WR_DLY(x) (((x) << 28) & GENMASK(31, 28)) +#define ICPU_MEMCTRL_TIMING0_RD_TO_WR_DLY_M GENMASK(31, 28) +#define ICPU_MEMCTRL_TIMING0_RD_TO_WR_DLY_X(x) (((x) & GENMASK(31, 28)) >> 28) +#define ICPU_MEMCTRL_TIMING0_WR_CS_CHANGE_DLY(x) (((x) << 24) & GENMASK(27, 24)) +#define ICPU_MEMCTRL_TIMING0_WR_CS_CHANGE_DLY_M GENMASK(27, 24) +#define ICPU_MEMCTRL_TIMING0_WR_CS_CHANGE_DLY_X(x) (((x) & GENMASK(27, 24)) >> 24) +#define ICPU_MEMCTRL_TIMING0_RD_CS_CHANGE_DLY(x) (((x) << 20) & GENMASK(23, 20)) +#define ICPU_MEMCTRL_TIMING0_RD_CS_CHANGE_DLY_M GENMASK(23, 20) +#define ICPU_MEMCTRL_TIMING0_RD_CS_CHANGE_DLY_X(x) (((x) & GENMASK(23, 20)) >> 20) +#define ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY(x) (((x) << 16) & GENMASK(19, 16)) +#define ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY_M GENMASK(19, 16) +#define ICPU_MEMCTRL_TIMING0_RAS_TO_PRECH_DLY_X(x) (((x) & GENMASK(19, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY(x) (((x) << 12) & GENMASK(15, 12)) +#define ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY_M GENMASK(15, 12) +#define ICPU_MEMCTRL_TIMING0_WR_TO_PRECH_DLY_X(x) (((x) & GENMASK(15, 12)) >> 12) +#define ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY(x) (((x) << 8) & GENMASK(11, 8)) +#define ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY_M GENMASK(11, 8) +#define ICPU_MEMCTRL_TIMING0_RD_TO_PRECH_DLY_X(x) (((x) & GENMASK(11, 8)) >> 8) +#define ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY_M GENMASK(7, 4) +#define ICPU_MEMCTRL_TIMING0_WR_DATA_XFR_DLY_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_TIMING0_RD_DATA_XFR_DLY(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_TIMING0_RD_DATA_XFR_DLY_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_TIMING1 0x128 + +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY(x) (((x) << 24) & GENMASK(31, 24)) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY_M GENMASK(31, 24) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_SAME_BANK_DLY_X(x) (((x) & GENMASK(31, 24)) >> 24) +#define ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY(x) (((x) << 16) & GENMASK(23, 16)) +#define ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY_M GENMASK(23, 16) +#define ICPU_MEMCTRL_TIMING1_BANK8_FAW_DLY_X(x) (((x) & GENMASK(23, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY(x) (((x) << 12) & GENMASK(15, 12)) +#define ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY_M GENMASK(15, 12) +#define ICPU_MEMCTRL_TIMING1_PRECH_TO_RAS_DLY_X(x) (((x) & GENMASK(15, 12)) >> 12) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY(x) (((x) << 8) & GENMASK(11, 8)) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY_M GENMASK(11, 8) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_RAS_DLY_X(x) (((x) & GENMASK(11, 8)) >> 8) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY_M GENMASK(7, 4) +#define ICPU_MEMCTRL_TIMING1_RAS_TO_CAS_DLY_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_TIMING1_WR_TO_RD_DLY(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_TIMING1_WR_TO_RD_DLY_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_TIMING2 0x12c + +#define ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY(x) (((x) << 28) & GENMASK(31, 28)) +#define ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY_M GENMASK(31, 28) +#define ICPU_MEMCTRL_TIMING2_PRECH_ALL_DLY_X(x) (((x) & GENMASK(31, 28)) >> 28) +#define ICPU_MEMCTRL_TIMING2_MDSET_DLY(x) (((x) << 24) & GENMASK(27, 24)) +#define ICPU_MEMCTRL_TIMING2_MDSET_DLY_M GENMASK(27, 24) +#define ICPU_MEMCTRL_TIMING2_MDSET_DLY_X(x) (((x) & GENMASK(27, 24)) >> 24) +#define ICPU_MEMCTRL_TIMING2_REF_DLY(x) (((x) << 16) & GENMASK(23, 16)) +#define ICPU_MEMCTRL_TIMING2_REF_DLY_M GENMASK(23, 16) +#define ICPU_MEMCTRL_TIMING2_REF_DLY_X(x) (((x) & GENMASK(23, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING2_INIT_DLY(x) ((x) & GENMASK(15, 0)) +#define ICPU_MEMCTRL_TIMING2_INIT_DLY_M GENMASK(15, 0) + +#define ICPU_MEMCTRL_TIMING3 0x130 + +#define ICPU_MEMCTRL_TIMING3_RMW_DLY(x) (((x) << 16) & GENMASK(19, 16)) +#define ICPU_MEMCTRL_TIMING3_RMW_DLY_M GENMASK(19, 16) +#define ICPU_MEMCTRL_TIMING3_RMW_DLY_X(x) (((x) & GENMASK(19, 16)) >> 16) +#define ICPU_MEMCTRL_TIMING3_ODT_RD_DLY(x) (((x) << 12) & GENMASK(15, 12)) +#define ICPU_MEMCTRL_TIMING3_ODT_RD_DLY_M GENMASK(15, 12) +#define ICPU_MEMCTRL_TIMING3_ODT_RD_DLY_X(x) (((x) & GENMASK(15, 12)) >> 12) +#define ICPU_MEMCTRL_TIMING3_ODT_WR_DLY(x) (((x) << 8) & GENMASK(11, 8)) +#define ICPU_MEMCTRL_TIMING3_ODT_WR_DLY_M GENMASK(11, 8) +#define ICPU_MEMCTRL_TIMING3_ODT_WR_DLY_X(x) (((x) & GENMASK(11, 8)) >> 8) +#define ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY(x) (((x) << 4) & GENMASK(7, 4)) +#define ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY_M GENMASK(7, 4) +#define ICPU_MEMCTRL_TIMING3_LOCAL_ODT_RD_DLY_X(x) (((x) & GENMASK(7, 4)) >> 4) +#define ICPU_MEMCTRL_TIMING3_WR_TO_RD_CS_CHANGE_DLY(x) ((x) & GENMASK(3, 0)) +#define ICPU_MEMCTRL_TIMING3_WR_TO_RD_CS_CHANGE_DLY_M GENMASK(3, 0) + +#define ICPU_MEMCTRL_MR0_VAL 0x138 + +#define ICPU_MEMCTRL_MR1_VAL 0x13c + +#define ICPU_MEMCTRL_MR2_VAL 0x140 + +#define ICPU_MEMCTRL_MR3_VAL 0x144 + +#define ICPU_MEMCTRL_TERMRES_CTRL 0x148 + +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_EXT BIT(11) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_ENA(x) (((x) << 7) & GENMASK(10, 7)) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_ENA_M GENMASK(10, 7) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_RD_ENA_X(x) (((x) & GENMASK(10, 7)) >> 7) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_EXT BIT(6) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA(x) (((x) << 2) & GENMASK(5, 2)) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA_M GENMASK(5, 2) +#define ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA_X(x) (((x) & GENMASK(5, 2)) >> 2) +#define ICPU_MEMCTRL_TERMRES_CTRL_LOCAL_ODT_RD_EXT BIT(1) +#define ICPU_MEMCTRL_TERMRES_CTRL_LOCAL_ODT_RD_ENA BIT(0) + +#define ICPU_MEMCTRL_DQS_DLY(x) (0x150 + 0x4 * (x)) +#define ICPU_MEMCTRL_DQS_DLY_RSZ 0x4 + +#define ICPU_MEMCTRL_DQS_DLY_TRAIN_DQ_ENA BIT(11) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM1(x) (((x) << 8) & GENMASK(10, 8)) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM1_M GENMASK(10, 8) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM1_X(x) (((x) & GENMASK(10, 8)) >> 8) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM0(x) (((x) << 5) & GENMASK(7, 5)) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM0_M GENMASK(7, 5) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_TRM0_X(x) (((x) & GENMASK(7, 5)) >> 5) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY(x) ((x) & GENMASK(4, 0)) +#define ICPU_MEMCTRL_DQS_DLY_DQS_DLY_M GENMASK(4, 0) + +#define ICPU_MEMPHY_CFG 0x160 + +#define ICPU_MEMPHY_CFG_PHY_FLUSH_DIS BIT(10) +#define ICPU_MEMPHY_CFG_PHY_RD_ADJ_DIS BIT(9) +#define ICPU_MEMPHY_CFG_PHY_DQS_EXT BIT(8) +#define ICPU_MEMPHY_CFG_PHY_FIFO_RST BIT(7) +#define ICPU_MEMPHY_CFG_PHY_DLL_BL_RST BIT(6) +#define ICPU_MEMPHY_CFG_PHY_DLL_CL_RST BIT(5) +#define ICPU_MEMPHY_CFG_PHY_ODT_OE BIT(4) +#define ICPU_MEMPHY_CFG_PHY_CK_OE BIT(3) +#define ICPU_MEMPHY_CFG_PHY_CL_OE BIT(2) +#define ICPU_MEMPHY_CFG_PHY_SSTL_ENA BIT(1) +#define ICPU_MEMPHY_CFG_PHY_RST BIT(0) + +#define ICPU_MEMPHY_DFT 0x164 + +#define ICPU_MEMPHY_DFT_PHY_DLL_BYPASS BIT(0) + +#define ICPU_MEMPHY_ZCAL 0x188 + +#define ICPU_MEMPHY_ZCAL_ZCAL_CLK_SEL BIT(9) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_ODT(x) (((x) << 5) & GENMASK(8, 5)) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_ODT_M GENMASK(8, 5) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_ODT_X(x) (((x) & GENMASK(8, 5)) >> 5) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG(x) (((x) << 1) & GENMASK(4, 1)) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_M GENMASK(4, 1) +#define ICPU_MEMPHY_ZCAL_ZCAL_PROG_X(x) (((x) & GENMASK(4, 1)) >> 1) +#define ICPU_MEMPHY_ZCAL_ZCAL_ENA BIT(0) + +#define ICPU_MEMPHY_ZCAL_STAT 0x18c + +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_ZCTRL(x) (((x) << 12) & GENMASK(31, 12)) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_ZCTRL_M GENMASK(31, 12) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_ZCTRL_X(x) (((x) & GENMASK(31, 12)) >> 12) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_ODTPU(x) (((x) << 8) & GENMASK(9, 8)) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_ODTPU_M GENMASK(9, 8) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_ODTPU_X(x) (((x) & GENMASK(9, 8)) >> 8) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_ODTPD(x) (((x) << 6) & GENMASK(7, 6)) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_ODTPD_M GENMASK(7, 6) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_ODTPD_X(x) (((x) & GENMASK(7, 6)) >> 6) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_PU(x) (((x) << 4) & GENMASK(5, 4)) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_PU_M GENMASK(5, 4) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_PU_X(x) (((x) & GENMASK(5, 4)) >> 4) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_PD(x) (((x) << 2) & GENMASK(3, 2)) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_PD_M GENMASK(3, 2) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_STAT_PD_X(x) (((x) & GENMASK(3, 2)) >> 2) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_ERR BIT(1) +#define ICPU_MEMPHY_ZCAL_STAT_ZCAL_DONE BIT(0) +#endif diff --git a/arch/mips/mach-mscc/include/mach/tlb.h b/arch/mips/mach-mscc/include/mach/tlb.h new file mode 100644 index 0000000000..4e95da28ce --- /dev/null +++ b/arch/mips/mach-mscc/include/mach/tlb.h @@ -0,0 +1,65 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#ifndef __ASM_MACH_TLB_H +#define __ASM_MACH_TLB_H + +#include <asm/mipsregs.h> +#include <mach/common.h> +#include <linux/sizes.h> + +#define TLB_HI_MASK 0xffffe000 +#define TLB_LO_MASK 0x3fffffff /* Masks off Fill bits */ +#define TLB_LO_SHIFT 6 /* PFN Start bit */ + +#define PAGEMASK_SHIFT 13 + +#define MMU_PAGE_CACHED (3 << 3) /* C(5:3) Cache Coherency Attributes */ +#define MMU_PAGE_UNCACHED (2 << 3) /* C(5:3) Cache Coherency Attributes */ +#define MMU_PAGE_DIRTY BIT(2) /* = Writeable */ +#define MMU_PAGE_VALID BIT(1) +#define MMU_PAGE_GLOBAL BIT(0) +#define MMU_REGIO_RO_C (MMU_PAGE_CACHED|MMU_PAGE_VALID|MMU_PAGE_GLOBAL) +#define MMU_REGIO_RO (MMU_PAGE_UNCACHED|MMU_PAGE_VALID|MMU_PAGE_GLOBAL) +#define MMU_REGIO_RW (MMU_PAGE_DIRTY|MMU_REGIO_RO) +#define MMU_REGIO_INVAL (MMU_PAGE_GLOBAL) + +#define TLB_COUNT_MASK GENMASK(5, 0) +#define TLB_COUNT_OFF 25 + +static inline u32 get_tlb_count(void) +{ + register u32 config1; + + config1 = read_c0_config1(); + config1 >>= TLB_COUNT_OFF; + config1 &= TLB_COUNT_MASK; + + return 1 + config1; +} + +static inline void create_tlb(int index, u32 offset, u32 size, u32 tlb_attrib1, + u32 tlb_attrib2) +{ + register u32 tlb_mask, tlb_lo0, tlb_lo1; + + tlb_mask = ((size >> 12) - 1) << PAGEMASK_SHIFT; + tlb_lo0 = tlb_attrib1 | ( offset >> TLB_LO_SHIFT); + tlb_lo1 = tlb_attrib2 | ((offset + size ) >> TLB_LO_SHIFT); + + write_one_tlb(index, tlb_mask, offset & TLB_HI_MASK, + tlb_lo0 & TLB_LO_MASK, tlb_lo1 & TLB_LO_MASK); +} + +static inline void init_tlb(void) +{ + register int i, max; + + max = get_tlb_count(); + for(i = 0; i < max; i++) + create_tlb(i, i * SZ_1M, SZ_4K, MMU_REGIO_INVAL, MMU_REGIO_INVAL); +} + +#endif /* __ASM_MACH_TLB_H */ diff --git a/arch/mips/mach-mscc/lowlevel_init.S b/arch/mips/mach-mscc/lowlevel_init.S new file mode 100644 index 0000000000..87439439f0 --- /dev/null +++ b/arch/mips/mach-mscc/lowlevel_init.S @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#include <asm/asm.h> +#include <asm/regdef.h> + + .text + .set noreorder + .extern vcoreiii_tlb_init +#ifdef CONFIG_SOC_LUTON + .extern pll_init +#endif + +LEAF(lowlevel_init) + // As we have no stack yet, we can assume the restricted + // luxury of the sX-registers without saving them + move s0,ra + + jal vcoreiii_tlb_init + nop +#ifdef CONFIG_SOC_LUTON + jal pll_init + nop +#endif + jr s0 + nop +END(lowlevel_init) diff --git a/arch/mips/mach-mscc/lowlevel_init_luton.S b/arch/mips/mach-mscc/lowlevel_init_luton.S new file mode 100644 index 0000000000..5e1b4442d9 --- /dev/null +++ b/arch/mips/mach-mscc/lowlevel_init_luton.S @@ -0,0 +1,63 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#include <asm/asm.h> +#include <asm/regdef.h> + +#define BASE_MACRO 0x600a0000 +#define REG_OFFSET(t, o) (t + (o*4)) +#define REG_MACRO(x) REG_OFFSET(BASE_MACRO, x) +#define BIT(nr) (1 << (nr)) + +#define MACRO_CTRL_PLL5G_STATUS_PLL5G_STATUS0 REG_MACRO(6) +#define MACRO_CTRL_PLL5G_STATUS_PLL5G_STATUS0_LOCK_STATUS BIT(0) +#define MACRO_CTRL_PLL5G_CFG_PLL5G_CFG2 REG_MACRO(2) +#define MACRO_CTRL_PLL5G_CFG_PLL5G_CFG0 REG_MACRO(0) +#define MACRO_CTRL_PLL5G_CFG_PLL5G_CFG0_CPU_CLK_DIV (0x3F << 6) +#define MACRO_CTRL_PLL5G_CFG_PLL5G_CFG0_CPU_CLK_DIV_ENC(x) (x << 6) + + .text + .set noreorder +LEAF(pll_init) + # Make sure PLL is locked + lw v0, MACRO_CTRL_PLL5G_STATUS_PLL5G_STATUS0 + andi v1, v0, MACRO_CTRL_PLL5G_STATUS_PLL5G_STATUS0_LOCK_STATUS + bne v1, zero, 1f + nop + + # Black magic from frontend + li v1, 0x00610400 + sw v1, MACRO_CTRL_PLL5G_CFG_PLL5G_CFG2 + + li v1, 0x00610c00 + sw v1, MACRO_CTRL_PLL5G_CFG_PLL5G_CFG2 + + li v1, 0x00610800 + sw v1, MACRO_CTRL_PLL5G_CFG_PLL5G_CFG2 + + li v1, 0x00610000 + sw v1, MACRO_CTRL_PLL5G_CFG_PLL5G_CFG2 + + # Wait for lock +2: lw v0, MACRO_CTRL_PLL5G_STATUS_PLL5G_STATUS0 + andi v1, v0, MACRO_CTRL_PLL5G_STATUS_PLL5G_STATUS0_LOCK_STATUS + # Keep looping if zero (no lock bit yet) + beq v1, zero, 2b + nop + + # Setup PLL CPU clock divider for 416MHz +1: lw v0, MACRO_CTRL_PLL5G_CFG_PLL5G_CFG0 + + # Keep reserved bits + li v1, ~MACRO_CTRL_PLL5G_CFG_PLL5G_CFG0_CPU_CLK_DIV + and v0, v0, v1 + + # Set code 6 ~ 416.66 MHz + ori v0, v0, MACRO_CTRL_PLL5G_CFG_PLL5G_CFG0_CPU_CLK_DIV_ENC(6) + + sw v0, MACRO_CTRL_PLL5G_CFG_PLL5G_CFG0 + jr ra + nop +END(pll_init) diff --git a/arch/mips/mach-mscc/reset.c b/arch/mips/mach-mscc/reset.c new file mode 100644 index 0000000000..85768cbdf0 --- /dev/null +++ b/arch/mips/mach-mscc/reset.c @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +#include <common.h> + +#include <asm/sections.h> +#include <asm/io.h> + +#include <asm/reboot.h> + +void _machine_restart(void) +{ + register u32 resetbits = PERF_SOFT_RST_SOFT_CHIP_RST; + (void) readl(REG_GCB(PERF_SOFT_RST)); + + /* + * Make sure VCore is NOT protected from reset + */ + writel(readl(REG_CFG(ICPU_RESET)) & ~ICPU_RESET_CORE_RST_PROTECT, + REG_CFG(ICPU_RESET)); + + /* + * Change to SPI bitbang for SPI reset workaround... + */ + writel(ICPU_SW_MODE_SW_SPI_CS_OE(1) | ICPU_SW_MODE_SW_SPI_CS(1) | + ICPU_SW_MODE_SW_PIN_CTRL_MODE, REG_CFG(ICPU_SW_MODE)); + + /* + * Do the global reset + */ + writel(resetbits, REG_GCB(PERF_SOFT_RST)); + + while (1) + /* NOP */; +}