[U-Boot] [PATCH v2 1/3] MX5: Add initial support for MX53 processor
Add initial support for Freescale MX53 processor,
- Add the iomux support and the pin definition, - Add the regs definition, clean up some unused def from mx51, - Add the low level init support, make use the freq input of setup_pll macro
--- Changes for v2: -address some comments of Stefano Babic, remove the is_soc_type and use #ifdef, -address the comments of stefano, remove CPU_TYPE def, remove something like /*0x760*/ comments in mx5x_pins.h. -fix the build break for vision2 board
Signed-off-by: Jason Liu r64343@freescale.com --- arch/arm/cpu/armv7/mx5/iomux.c | 30 ++- arch/arm/cpu/armv7/mx5/lowlevel_init.S | 91 +++--- arch/arm/cpu/armv7/mx5/soc.c | 22 +- arch/arm/include/asm/arch-mx5/asm-offsets.h | 5 + arch/arm/include/asm/arch-mx5/imx-regs.h | 78 ++--- arch/arm/include/asm/arch-mx5/iomux.h | 102 ------ arch/arm/include/asm/arch-mx5/mx5x_pins.h | 469 ++++++++++++++++++++++++++- include/configs/mx51evk.h | 3 +- include/configs/vision2.h | 3 +- 9 files changed, 599 insertions(+), 204 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx5/iomux.c b/arch/arm/cpu/armv7/mx5/iomux.c old mode 100644 new mode 100755 index e8928d5..d4e3bbb --- a/arch/arm/cpu/armv7/mx5/iomux.c +++ b/arch/arm/cpu/armv7/mx5/iomux.c @@ -34,7 +34,7 @@ enum iomux_reg_addr { IOMUXSW_MUX_CTL = IOMUXC_BASE_ADDR, IOMUXSW_MUX_END = IOMUXC_BASE_ADDR + MUX_I_END, IOMUXSW_PAD_CTL = IOMUXC_BASE_ADDR + PAD_I_START, - IOMUXSW_INPUT_CTL = IOMUXC_BASE_ADDR, + IOMUXSW_INPUT_CTL = IOMUXC_BASE_ADDR + INPUT_CTL_START, };
#define MUX_PIN_NUM_MAX (((MUX_I_END - MUX_I_START) >> 2) + 1) @@ -44,11 +44,12 @@ static inline u32 get_mux_reg(iomux_pin_name_t pin) { u32 mux_reg = PIN_TO_IOMUX_MUX(pin);
+#if defined(CONFIG_MX51) if (is_soc_rev(CHIP_REV_2_0) < 0) { /* * Fixup register address: - * i.MX51 TO1 has offset with the register - * which is define as TO2. + * i.MX51 TO1 has offset with the register + * which is define as TO2. */ if ((pin == MX51_PIN_NANDF_RB5) || (pin == MX51_PIN_NANDF_RB6) || @@ -59,6 +60,7 @@ static inline u32 get_mux_reg(iomux_pin_name_t pin) else if (mux_reg >= 0x130) mux_reg += 0xC; } +#endif mux_reg += IOMUXSW_MUX_CTL; return mux_reg; } @@ -68,11 +70,12 @@ static inline u32 get_pad_reg(iomux_pin_name_t pin) { u32 pad_reg = PIN_TO_IOMUX_PAD(pin);
+#if defined(CONFIG_MX51) if (is_soc_rev(CHIP_REV_2_0) < 0) { /* * Fixup register address: - * i.MX51 TO1 has offset with the register - * which is define as TO2. + * i.MX51 TO1 has offset with the register + * which is define as TO2. */ if ((pin == MX51_PIN_NANDF_RB5) || (pin == MX51_PIN_NANDF_RB6) || @@ -91,6 +94,7 @@ static inline u32 get_pad_reg(iomux_pin_name_t pin) else pad_reg += 8; } +#endif pad_reg += IOMUXSW_PAD_CTL; return pad_reg; } @@ -98,10 +102,13 @@ static inline u32 get_pad_reg(iomux_pin_name_t pin) /* Get the last iomux register address */ static inline u32 get_mux_end(void) { +#if defined(CONFIG_MX51) if (is_soc_rev(CHIP_REV_2_0) < 0) return IOMUXC_BASE_ADDR + (0x3F8 - 4); else return IOMUXC_BASE_ADDR + (0x3F0 - 4); +#endif + return IOMUXSW_MUX_END; }
/* @@ -164,3 +171,16 @@ unsigned int mxc_iomux_get_pad(iomux_pin_name_t pin) u32 pad_reg = get_pad_reg(pin); return readl(pad_reg); } + +/* + * This function configures daisy-chain + * + * @param input index of input select register + * @param config the binary value of elements + */ +void mxc_iomux_set_input(iomux_input_select_t input, u32 config) +{ + u32 reg = IOMUXSW_INPUT_CTL + (input << 2); + + writel(config, reg); +} diff --git a/arch/arm/cpu/armv7/mx5/lowlevel_init.S b/arch/arm/cpu/armv7/mx5/lowlevel_init.S old mode 100644 new mode 100755 index e984870..96ebfe2 --- a/arch/arm/cpu/armv7/mx5/lowlevel_init.S +++ b/arch/arm/cpu/armv7/mx5/lowlevel_init.S @@ -70,6 +70,7 @@
/* M4IF setup */ .macro init_m4if +#ifdef CONFIG_MX51 /* VPU and IPU given higher priority (0x4) * IPU accesses with ID=0x1 given highest priority (=0xA) */ @@ -87,27 +88,31 @@ ldr r1, =0x001901A3 str r1, [r0, #0x48]
+#endif .endm /* init_m4if */
.macro setup_pll pll, freq - ldr r2, =\pll + ldr r0, =\pll ldr r1, =0x00001232 - str r1, [r2, #PLL_DP_CTL] /* Set DPLL ON (set UPEN bit): BRMO=1 */ + str r1, [r0, #PLL_DP_CTL] /* Set DPLL ON (set UPEN bit): BRMO=1 */ mov r1, #0x2 - str r1, [r2, #PLL_DP_CONFIG] /* Enable auto-restart AREN bit */ + str r1, [r0, #PLL_DP_CONFIG] /* Enable auto-restart AREN bit */
- str r3, [r2, #PLL_DP_OP] - str r3, [r2, #PLL_DP_HFS_OP] + ldr r1, W_DP_OP_\freq + str r1, [r0, #PLL_DP_OP] + str r1, [r0, #PLL_DP_HFS_OP]
- str r4, [r2, #PLL_DP_MFD] - str r4, [r2, #PLL_DP_HFS_MFD] + ldr r1, W_DP_MFD_\freq + str r1, [r0, #PLL_DP_MFD] + str r1, [r0, #PLL_DP_HFS_MFD]
- str r5, [r2, #PLL_DP_MFN] - str r5, [r2, #PLL_DP_HFS_MFN] + ldr r1, W_DP_MFN_\freq + str r1, [r0, #PLL_DP_MFN] + str r1, [r0, #PLL_DP_HFS_MFN]
ldr r1, =0x00001232 - str r1, [r2, #PLL_DP_CTL] -1: ldr r1, [r2, #PLL_DP_CTL] + str r1, [r0, #PLL_DP_CTL] +1: ldr r1, [r0, #PLL_DP_CTL] ands r1, r1, #0x1 beq 1b .endm @@ -115,6 +120,7 @@ .macro init_clock ldr r0, =CCM_BASE_ADDR
+#if defined(CONFIG_MX51) /* Gate of clocks to the peripherals first */ ldr r1, =0x3FFFFFFF str r1, [r0, #CLKCTL_CCGR0] @@ -141,19 +147,16 @@ 1: ldr r1, [r0, #CLKCTL_CDHIPR] cmp r1, #0x0 bne 1b +#endif
/* Switch ARM to step clock */ mov r1, #0x4 str r1, [r0, #CLKCTL_CCSR] - mov r3, #DP_OP_800 - mov r4, #DP_MFD_800 - mov r5, #DP_MFN_800 - setup_pll PLL1_BASE_ADDR
- mov r3, #DP_OP_665 - mov r4, #DP_MFD_665 - mov r5, #DP_MFN_665 - setup_pll PLL3_BASE_ADDR + setup_pll PLL1_BASE_ADDR, 800 + +#if defined(CONFIG_MX51) + setup_pll PLL3_BASE_ADDR, 665
/* Switch peripheral to PLL 3 */ ldr r0, =CCM_BASE_ADDR @@ -162,10 +165,7 @@ str r1, [r0, #CLKCTL_CBCMR] ldr r1, =0x13239145 str r1, [r0, #CLKCTL_CBCDR] - mov r3, #DP_OP_665 - mov r4, #DP_MFD_665 - mov r5, #DP_MFN_665 - setup_pll PLL2_BASE_ADDR + setup_pll PLL2_BASE_ADDR, 665
/* Switch peripheral to PLL2 */ ldr r0, =CCM_BASE_ADDR @@ -174,12 +174,8 @@ ldr r1, =0x000020C0 orr r1,r1,#CONFIG_SYS_DDR_CLKSEL str r1, [r0, #CLKCTL_CBCMR] - - mov r3, #DP_OP_216 - mov r4, #DP_MFD_216 - mov r5, #DP_MFN_216 - setup_pll PLL3_BASE_ADDR - +#endif + setup_pll PLL3_BASE_ADDR, 216
/* Set the platform clock dividers */ ldr r0, =ARM_BASE_ADDR @@ -188,18 +184,23 @@
ldr r0, =CCM_BASE_ADDR
+#if defined(CONFIG_MX51) /* Run 3.0 at Full speed, for other TO's wait till we increase VDDGP */ ldr r1, =0x0 ldr r3, [r1, #ROM_SI_REV] cmp r3, #0x10 movls r1, #0x1 movhi r1, #0 - str r1, [r0, #CLKCTL_CACRR] +#else + mov r1, #0
+#endif + str r1, [r0, #CLKCTL_CACRR] /* Switch ARM back to PLL 1 */ mov r1, #0 str r1, [r0, #CLKCTL_CCSR]
+#if defined(CONFIG_MX51) /* setup the rest */ /* Use lp_apm (24MHz) source for perclk */ ldr r1, =0x000020C2 @@ -208,6 +209,7 @@ /* ddr clock from PLL 1, all perclk dividers are 1 since using 24MHz */ ldr r1, =CONFIG_SYS_CLKTL_CBCDR str r1, [r0, #CLKCTL_CBCDR] +#endif
/* Restore the default values in the Gate registers */ ldr r1, =0xFFFFFFFF @@ -218,13 +220,23 @@ str r1, [r0, #CLKCTL_CCGR4] str r1, [r0, #CLKCTL_CCGR5] str r1, [r0, #CLKCTL_CCGR6] +#if defined(CONFIG_MX53) + str r1, [r0, #CLKCTL_CCGR7] +#endif
+#if defined(CONFIG_MX51) /* Use PLL 2 for UART's, get 66.5MHz from it */ ldr r1, =0xA5A2A020 str r1, [r0, #CLKCTL_CSCMR1] ldr r1, =0x00C30321 str r1, [r0, #CLKCTL_CSCDR1] - +#elif defined(CONFIG_MX53) + ldr r1, [r0, #CLKCTL_CSCDR1] + orr r1, r1, #0x3f + eor r1, r1, #0x3f + orr r1, r1, #0x21 + str r1, [r0, #CLKCTL_CSCDR1] +#endif /* make sure divider effective */ 1: ldr r1, [r0, #CLKCTL_CDHIPR] cmp r1, #0x0 @@ -249,6 +261,7 @@
.globl lowlevel_init lowlevel_init: +#if defined(CONFIG_MX51) ldr r0, =GPIO1_BASE_ADDR ldr r1, [r0, #0x0] orr r1, r1, #(1 << 23) @@ -256,6 +269,7 @@ lowlevel_init: ldr r1, [r0, #0x4] orr r1, r1, #(1 << 23) str r1, [r0, #0x4] +#endif
init_l2cc
@@ -269,9 +283,12 @@ lowlevel_init: mov pc,lr
/* Board level setting value */ -DDR_PERCHARGE_CMD: .word 0x04008008 -DDR_REFRESH_CMD: .word 0x00008010 -DDR_LMR1_W: .word 0x00338018 -DDR_LMR_CMD: .word 0xB2220000 -DDR_TIMING_W: .word 0xB02567A9 -DDR_MISC_W: .word 0x000A0104 +W_DP_OP_800: .word DP_OP_800 +W_DP_MFD_800: .word DP_MFD_800 +W_DP_MFN_800: .word DP_MFN_800 +W_DP_OP_665: .word DP_OP_665 +W_DP_MFD_665: .word DP_MFD_665 +W_DP_MFN_665: .word DP_MFN_665 +W_DP_OP_216: .word DP_OP_216 +W_DP_MFD_216: .word DP_MFD_216 +W_DP_MFN_216: .word DP_MFN_216 diff --git a/arch/arm/cpu/armv7/mx5/soc.c b/arch/arm/cpu/armv7/mx5/soc.c index 2900119..09500b3 100644 --- a/arch/arm/cpu/armv7/mx5/soc.c +++ b/arch/arm/cpu/armv7/mx5/soc.c @@ -33,17 +33,20 @@ #include <fsl_esdhc.h> #endif
-#if defined(CONFIG_MX51) -#define CPU_TYPE 0x51000 -#else +#if !(defined(CONFIG_MX51) || defined(CONFIG_MX53)) #error "CPU_TYPE not defined" #endif
u32 get_cpu_rev(void) { - int system_rev = CPU_TYPE; +#ifdef CONFIG_MX51 + int system_rev = 0x51000; +#else + int system_rev = 0x53000; +#endif int reg = __raw_readl(ROM_SI_REV);
+#if defined(CONFIG_MX51) switch (reg) { case 0x02: system_rev |= CHIP_REV_1_1; @@ -57,11 +60,20 @@ u32 get_cpu_rev(void) case 0x20: system_rev |= CHIP_REV_3_0; break; - return system_rev; default: system_rev |= CHIP_REV_1_0; break; } +#else + switch (reg) { + case 0x20: + system_rev |= CHIP_REV_2_0; + break; + default: + system_rev |= CHIP_REV_1_0; + break; + } +#endif return system_rev; }
diff --git a/arch/arm/include/asm/arch-mx5/asm-offsets.h b/arch/arm/include/asm/arch-mx5/asm-offsets.h index afd2728..2258f2f 100644 --- a/arch/arm/include/asm/arch-mx5/asm-offsets.h +++ b/arch/arm/include/asm/arch-mx5/asm-offsets.h @@ -37,7 +37,12 @@ #define CLKCTL_CCGR4 0x78 #define CLKCTL_CCGR5 0x7C #define CLKCTL_CCGR6 0x80 +#if defined(CONFIG_MX53) +#define CLKCTL_CCGR7 0x84 #define CLKCTL_CMEOR 0x84 +#elif defined(CONFIG_MX51) +#define CLKCTL_CMEOR 0x84 +#endif
/* DPLL */ #define PLL_DP_CTL 0x00 diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h old mode 100644 new mode 100755 index b45026d..8be7f4b --- a/arch/arm/include/asm/arch-mx5/imx-regs.h +++ b/arch/arm/include/asm/arch-mx5/imx-regs.h @@ -20,38 +20,36 @@ * MA 02111-1307 USA */
-#ifndef __ASM_ARCH_MXC_MX51_H__ -#define __ASM_ARCH_MXC_MX51_H__ +#ifndef __ASM_ARCH_MX5_IMX_REGS_H__ +#define __ASM_ARCH_MX5_IMX_REGS_H__
-/* - * IRAM - */ +#if defined(CONFIG_MX51) #define IRAM_BASE_ADDR 0x1FFE0000 /* internal ram */ -#define IRAM_SIZE 0x00020000 /* 128 KB */ -/* - * Graphics Memory of GPU - */ -#define GPU_BASE_ADDR 0x20000000 -#define GPU_CTRL_BASE_ADDR 0x30000000 #define IPU_CTRL_BASE_ADDR 0x40000000 -/* - * Debug - */ -#define DEBUG_BASE_ADDR 0x60000000 -#define ETB_BASE_ADDR (DEBUG_BASE_ADDR + 0x00001000) -#define ETM_BASE_ADDR (DEBUG_BASE_ADDR + 0x00002000) -#define TPIU_BASE_ADDR (DEBUG_BASE_ADDR + 0x00003000) -#define CTI0_BASE_ADDR (DEBUG_BASE_ADDR + 0x00004000) -#define CTI1_BASE_ADDR (DEBUG_BASE_ADDR + 0x00005000) -#define CTI2_BASE_ADDR (DEBUG_BASE_ADDR + 0x00006000) -#define CTI3_BASE_ADDR (DEBUG_BASE_ADDR + 0x00007000) -#define CORTEX_DBG_BASE_ADDR (DEBUG_BASE_ADDR + 0x00008000) +#define SPBA0_BASE_ADDR 0x70000000 +#define AIPS1_BASE_ADDR 0x73F00000 +#define AIPS2_BASE_ADDR 0x83F00000 +#define CSD0_BASE_ADDR 0x90000000 +#define CSD1_BASE_ADDR 0xA0000000 +#define NFC_BASE_ADDR_AXI 0xCFFF0000 +#elif defined(CONFIG_MX53) +#define IPU_CTRL_BASE_ADDR 0x18000000 +#define SPBA0_BASE_ADDR 0x50000000 +#define AIPS1_BASE_ADDR 0x53F00000 +#define AIPS2_BASE_ADDR 0x63F00000 +#define CSD0_BASE_ADDR 0x70000000 +#define CSD1_BASE_ADDR 0xB0000000 +#define NFC_BASE_ADDR_AXI 0xF7FF0000 +#define IRAM_BASE_ADDR 0xF8000000 +#else +#error "CPU_TYPE not defined" +#endif + +#define IRAM_SIZE 0x00020000 /* 128 KB */
/* * SPBA global module enabled #0 */ -#define SPBA0_BASE_ADDR 0x70000000 - #define MMC_SDHC1_BASE_ADDR (SPBA0_BASE_ADDR + 0x00004000) #define MMC_SDHC2_BASE_ADDR (SPBA0_BASE_ADDR + 0x00008000) #define UART3_BASE_ADDR (SPBA0_BASE_ADDR + 0x0000C000) @@ -68,8 +66,6 @@ /* * AIPS 1 */ -#define AIPS1_BASE_ADDR 0x73F00000 - #define OTG_BASE_ADDR (AIPS1_BASE_ADDR + 0x00080000) #define GPIO1_BASE_ADDR (AIPS1_BASE_ADDR + 0x00084000) #define GPIO2_BASE_ADDR (AIPS1_BASE_ADDR + 0x00088000) @@ -91,11 +87,14 @@ #define CCM_BASE_ADDR (AIPS1_BASE_ADDR + 0x000D4000) #define GPC_BASE_ADDR (AIPS1_BASE_ADDR + 0x000D8000)
+#if defined(CONFIG_MX53) +#define GPIO5_BASE_ADDR (AIPS1_BASE_ADDR + 0x000DC000) +#define GPIO6_BASE_ADDR (AIPS1_BASE_ADDR + 0x000E0000) +#define GPIO7_BASE_ADDR (AIPS1_BASE_ADDR + 0x000E4000) +#endif /* * AIPS 2 */ -#define AIPS2_BASE_ADDR 0x83F00000 - #define PLL1_BASE_ADDR (AIPS2_BASE_ADDR + 0x00080000) #define PLL2_BASE_ADDR (AIPS2_BASE_ADDR + 0x00084000) #define PLL3_BASE_ADDR (AIPS2_BASE_ADDR + 0x00088000) @@ -129,26 +128,7 @@ #define VPU_BASE_ADDR (AIPS2_BASE_ADDR + 0x000F4000) #define SAHARA_BASE_ADDR (AIPS2_BASE_ADDR + 0x000F8000)
-#define TZIC_BASE_ADDR 0x8FFFC000 - /* - * Memory regions and CS - */ -#define CSD0_BASE_ADDR 0x90000000 -#define CSD1_BASE_ADDR 0xA0000000 -#define CS0_BASE_ADDR 0xB0000000 -#define CS1_BASE_ADDR 0xB8000000 -#define CS2_BASE_ADDR 0xC0000000 -#define CS3_BASE_ADDR 0xC8000000 -#define CS4_BASE_ADDR 0xCC000000 -#define CS5_BASE_ADDR 0xCE000000 - -/* - * NFC - */ -#define NFC_BASE_ADDR_AXI 0xCFFF0000 /* NAND flash AXI */ - -/*! * Number of GPIO port as defined in the IC Spec */ #define GPIO_PORT_NUM 4 @@ -311,4 +291,4 @@ struct fuse_bank1_regs {
#endif /* __ASSEMBLER__*/
-#endif /* __ASM_ARCH_MXC_MX51_H__ */ +#endif /* __ASM_ARCH_MX5_IMX_REGS_H__ */ diff --git a/arch/arm/include/asm/arch-mx5/iomux.h b/arch/arm/include/asm/arch-mx5/iomux.h index 0d91a24..760371b 100644 --- a/arch/arm/include/asm/arch-mx5/iomux.h +++ b/arch/arm/include/asm/arch-mx5/iomux.h @@ -70,108 +70,6 @@ typedef enum iomux_pad_config { PAD_CTL_DRV_VOT_HIGH = 0x1 << 13,/* High voltage mode */ } iomux_pad_config_t;
-/* various IOMUX input select register index */ -typedef enum iomux_input_select { - MUX_IN_AUDMUX_P4_INPUT_DA_AMX_SELECT_I = 0, - MUX_IN_AUDMUX_P4_INPUT_DB_AMX_SELECT_I, - MUX_IN_AUDMUX_P4_INPUT_TXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P4_INPUT_TXFS_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_DA_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_DB_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_RXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_RXFS_AMX_SELECT, - MUX_IN_AUDMUX_P5_INPUT_TXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_TXFS_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_DA_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_DB_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_RXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_RXFS_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_TXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_TXFS_AMX_SELECT_INPUT, - MUX_IN_CCM_IPP_DI_CLK_SELECT_INPUT, - /* TO2 */ - MUX_IN_CCM_IPP_DI1_CLK_SELECT_INPUT, - MUX_IN_CCM_PLL1_BYPASS_CLK_SELECT_INPUT, - MUX_IN_CCM_PLL2_BYPASS_CLK_SELECT_INPUT, - MUX_IN_CSPI_IPP_CSPI_CLK_IN_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_MISO_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_MOSI_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_SS_B_1_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_SS_B_2_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_SS_B_3_SELECT_INPUT, - MUX_IN_DPLLIP1_L1T_TOG_EN_SELECT_INPUT, - /* TO2 */ - MUX_IN_ECSPI2_IPP_IND_SS_B_1_SELECT_INPUT, - MUX_IN_ECSPI2_IPP_IND_SS_B_3_SELECT_INPUT, - MUX_IN_EMI_IPP_IND_RDY_INT_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT0_IN_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT1_IN_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT2_IN_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT3_IN_SELECT_INPUT, - MUX_IN_FEC_FEC_COL_SELECT_INPUT, - MUX_IN_FEC_FEC_CRS_SELECT_INPUT, - MUX_IN_FEC_FEC_MDI_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_0_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_1_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_2_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_3_SELECT_INPUT, - MUX_IN_FEC_FEC_RX_CLK_SELECT_INPUT, - MUX_IN_FEC_FEC_RX_DV_SELECT_INPUT, - MUX_IN_FEC_FEC_RX_ER_SELECT_INPUT, - MUX_IN_FEC_FEC_TX_CLK_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_1_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_2_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_3_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_5_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_6_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_7_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_8_SELECT_INPUT, - /* TO2 */ - MUX_IN_GPIO3_IPP_IND_G_IN_12_SELECT_INPUT, - MUX_IN_HSC_MIPI_MIX_IPP_IND_SENS1_DATA_EN_SELECT_INPUT, - MUX_IN_HSC_MIPI_MIX_IPP_IND_SENS2_DATA_EN_SELECT_INPUT, - /* TO2 */ - MUX_IN_HSC_MIPI_MIX_PAR_VSYNC_SELECT_INPUT, - /* TO2 */ - MUX_IN_HSC_MIPI_MIX_PAR_DI_WAIT_SELECT_INPUT, - MUX_IN_HSC_MIPI_MIX_PAR_SISG_TRIG_SELECT_INPUT, - MUX_IN_I2C1_IPP_SCL_IN_SELECT_INPUT, - MUX_IN_I2C1_IPP_SDA_IN_SELECT_INPUT, - MUX_IN_I2C2_IPP_SCL_IN_SELECT_INPUT, - MUX_IN_I2C2_IPP_SDA_IN_SELECT_INPUT, - - MUX_IN_IPU_IPP_DI_0_IND_DISPB_SD_D_SELECT_INPUT, - - MUX_IN_IPU_IPP_DI_1_IND_DISPB_SD_D_SELECT_INPUT, - - MUX_IN_KPP_IPP_IND_COL_6_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_COL_7_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_4_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_5_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_6_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_7_SELECT_INPUT, - MUX_IN_UART1_IPP_UART_RTS_B_SELECT_INPUT, - MUX_IN_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, - MUX_IN_UART2_IPP_UART_RTS_B_SELECT_INPUT, - MUX_IN_UART2_IPP_UART_RXD_MUX_SELECT_INPUT, - MUX_IN_UART3_IPP_UART_RTS_B_SELECT_INPUT, - MUX_IN_UART3_IPP_UART_RXD_MUX_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_CLK_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_0_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_1_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_2_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_3_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_4_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_5_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_6_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_7_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DIR_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_NXT_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_STP_SELECT_INPUT, - MUX_INPUT_NUM_MUX, -} iomux_input_select_t; - /* various IOMUX input functions */ typedef enum iomux_input_config { INPUT_CTL_PATH0 = 0x0, diff --git a/arch/arm/include/asm/arch-mx5/mx5x_pins.h b/arch/arm/include/asm/arch-mx5/mx5x_pins.h old mode 100644 new mode 100755 index a564fce..4e3a31b --- a/arch/arm/include/asm/arch-mx5/mx5x_pins.h +++ b/arch/arm/include/asm/arch-mx5/mx5x_pins.h @@ -86,12 +86,22 @@ #define PIN_TO_PAD_MASK ((1 << (GPIO_I - PAD_I)) - 1) #define PIN_TO_ALT_GPIO_MASK ((1 << (MUX_IO_I - GPIO_I)) - 1)
-#define NON_MUX_I PIN_TO_MUX_MASK +#define NON_MUX_I PIN_TO_MUX_MASK +#define NON_PAD_I PIN_TO_PAD_MASK + +#if defined(CONFIG_MX51) #define MUX_I_START 0x001C #define PAD_I_START 0x3F0 #define INPUT_CTL_START 0x8C4 -#define INPUT_CTL_START_TO1 0x928 #define MUX_I_END (PAD_I_START - 4) +#elif defined(CONFIG_MX53) +#define MUX_I_START 0x0020 +#define PAD_I_START 0x348 +#define INPUT_CTL_START 0x730 +#define MUX_I_END (PAD_I_START - 4) +#else +#error "CPU_TYPE not defined" +#endif
#define _MXC_BUILD_PIN(gp, gi, ga, mi, pi) \ (((gp) << MUX_IO_P) | ((gi) << MUX_IO_I) | \ @@ -115,7 +125,7 @@ * "sw_pad_ctl & sw_mux_ctl details" of the MX51 IC Spec. Each enumerated * value is constructed based on the rules described above. */ -enum iomux_pins { +enum { MX51_PIN_EIM_DA0 = _MXC_BUILD_NON_GPIO_PIN(0x1C, 0x7A8), MX51_PIN_EIM_DA1 = _MXC_BUILD_NON_GPIO_PIN(0x20, 0x7A8), MX51_PIN_EIM_DA2 = _MXC_BUILD_NON_GPIO_PIN(0x24, 0x7A8), @@ -414,5 +424,458 @@ enum iomux_pins { MX51_PIN_CTL_DRAM_DQM3 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4E0), };
+enum { + MX53_PIN_GPIO_19 = _MXC_BUILD_GPIO_PIN(3, 5, 1, 0x20, 0x348), + MX53_PIN_KEY_COL0 = _MXC_BUILD_GPIO_PIN(3, 6, 1, 0x24, 0x34C), + MX53_PIN_KEY_ROW0 = _MXC_BUILD_GPIO_PIN(3, 7, 1, 0x28, 0x350), + MX53_PIN_KEY_COL1 = _MXC_BUILD_GPIO_PIN(3, 8, 1, 0x2C, 0x354), + MX53_PIN_KEY_ROW1 = _MXC_BUILD_GPIO_PIN(3, 9, 1, 0x30, 0x358), + MX53_PIN_KEY_COL2 = _MXC_BUILD_GPIO_PIN(3, 10, 1, 0x34, 0x35C), + MX53_PIN_KEY_ROW2 = _MXC_BUILD_GPIO_PIN(3, 11, 1, 0x38, 0x360), + MX53_PIN_KEY_COL3 = _MXC_BUILD_GPIO_PIN(3, 12, 1, 0x3C, 0x364), + MX53_PIN_KEY_ROW3 = _MXC_BUILD_GPIO_PIN(3, 13, 1, 0x40, 0x368), + MX53_PIN_KEY_COL4 = _MXC_BUILD_GPIO_PIN(3, 14, 1, 0x44, 0x36C), + MX53_PIN_KEY_ROW4 = _MXC_BUILD_GPIO_PIN(3, 15, 1, 0x48, 0x370), + MX53_PIN_NVCC_KEYPAD = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x374), + MX53_PIN_DI0_DISP_CLK = _MXC_BUILD_GPIO_PIN(3, 16, 1, 0x4C, 0x378), + MX53_PIN_DI0_PIN15 = _MXC_BUILD_GPIO_PIN(3, 17, 1, 0x50, 0x37C), + MX53_PIN_DI0_PIN2 = _MXC_BUILD_GPIO_PIN(3, 18, 1, 0x54, 0x380), + MX53_PIN_DI0_PIN3 = _MXC_BUILD_GPIO_PIN(3, 19, 1, 0x58, 0x384), + MX53_PIN_DI0_PIN4 = _MXC_BUILD_GPIO_PIN(3, 20, 1, 0x5C, 0x388), + MX53_PIN_DISP0_DAT0 = _MXC_BUILD_GPIO_PIN(3, 21, 1, 0x60, 0x38C), + MX53_PIN_DISP0_DAT1 = _MXC_BUILD_GPIO_PIN(3, 22, 1, 0x64, 0x390), + MX53_PIN_DISP0_DAT2 = _MXC_BUILD_GPIO_PIN(3, 23, 1, 0x68, 0x394), + MX53_PIN_DISP0_DAT3 = _MXC_BUILD_GPIO_PIN(3, 24, 1, 0x6C, 0x398), + MX53_PIN_DISP0_DAT4 = _MXC_BUILD_GPIO_PIN(3, 25, 1, 0x70, 0x39C), + MX53_PIN_DISP0_DAT5 = _MXC_BUILD_GPIO_PIN(3, 26, 1, 0x74, 0x3A0), + MX53_PIN_DISP0_DAT6 = _MXC_BUILD_GPIO_PIN(3, 27, 1, 0x78, 0x3A4), + MX53_PIN_DISP0_DAT7 = _MXC_BUILD_GPIO_PIN(3, 28, 1, 0x7C, 0x3A8), + MX53_PIN_DISP0_DAT8 = _MXC_BUILD_GPIO_PIN(3, 29, 1, 0x80, 0x3AC), + MX53_PIN_DISP0_DAT9 = _MXC_BUILD_GPIO_PIN(3, 30, 1, 0x84, 0x3B0), + MX53_PIN_DISP0_DAT10 = _MXC_BUILD_GPIO_PIN(3, 31, 1, 0x88, 0x3B4), + MX53_PIN_DISP0_DAT11 = _MXC_BUILD_GPIO_PIN(4, 5, 1, 0x8C, 0x3B8), + MX53_PIN_DISP0_DAT12 = _MXC_BUILD_GPIO_PIN(4, 6, 1, 0x90, 0x3BC), + MX53_PIN_DISP0_DAT13 = _MXC_BUILD_GPIO_PIN(4, 7, 1, 0x94, 0x3C0), + MX53_PIN_DISP0_DAT14 = _MXC_BUILD_GPIO_PIN(4, 8, 1, 0x98, 0x3C4), + MX53_PIN_DISP0_DAT15 = _MXC_BUILD_GPIO_PIN(4, 9, 1, 0x9C, 0x3C8), + MX53_PIN_DISP0_DAT16 = _MXC_BUILD_GPIO_PIN(4, 10, 1, 0xA0, 0x3CC), + MX53_PIN_DISP0_DAT17 = _MXC_BUILD_GPIO_PIN(4, 11, 1, 0xA4, 0x3D0), + MX53_PIN_DISP0_DAT18 = _MXC_BUILD_GPIO_PIN(4, 12, 1, 0xA8, 0x3D4), + MX53_PIN_DISP0_DAT19 = _MXC_BUILD_GPIO_PIN(4, 13, 1, 0xAC, 0x3D8), + MX53_PIN_DISP0_DAT20 = _MXC_BUILD_GPIO_PIN(4, 14, 1, 0xB0, 0x3DC), + MX53_PIN_DISP0_DAT21 = _MXC_BUILD_GPIO_PIN(4, 15, 1, 0xB4, 0x3E0), + MX53_PIN_DISP0_DAT22 = _MXC_BUILD_GPIO_PIN(4, 16, 1, 0xB8, 0x3E4), + MX53_PIN_DISP0_DAT23 = _MXC_BUILD_GPIO_PIN(4, 17, 1, 0xBC, 0x3E8), + MX53_PIN_CSI0_PIXCLK = _MXC_BUILD_GPIO_PIN(4, 18, 1, 0xC0, 0x3EC), + MX53_PIN_CSI0_MCLK = _MXC_BUILD_GPIO_PIN(4, 19, 1, 0xC4, 0x3F0), + MX53_PIN_CSI0_DATA_EN = _MXC_BUILD_GPIO_PIN(4, 20, 1, 0xC8, 0x3F4), + MX53_PIN_CSI0_VSYNC = _MXC_BUILD_GPIO_PIN(4, 21, 1, 0xCC, 0x3F8), + MX53_PIN_CSI0_D4 = _MXC_BUILD_GPIO_PIN(4, 22, 1, 0xD0, 0x3FC), + MX53_PIN_CSI0_D5 = _MXC_BUILD_GPIO_PIN(4, 23, 1, 0xD4, 0x400), + MX53_PIN_CSI0_D6 = _MXC_BUILD_GPIO_PIN(4, 24, 1, 0xD8, 0x404), + MX53_PIN_CSI0_D7 = _MXC_BUILD_GPIO_PIN(4, 25, 1, 0xDC, 0x408), + MX53_PIN_CSI0_D8 = _MXC_BUILD_GPIO_PIN(4, 26, 1, 0xE0, 0x40C), + MX53_PIN_CSI0_D9 = _MXC_BUILD_GPIO_PIN(4, 27, 1, 0xE4, 0x410), + MX53_PIN_CSI0_D10 = _MXC_BUILD_GPIO_PIN(4, 28, 1, 0xE8, 0x414), + MX53_PIN_CSI0_D11 = _MXC_BUILD_GPIO_PIN(4, 29, 1, 0xEC, 0x418), + MX53_PIN_CSI0_D12 = _MXC_BUILD_GPIO_PIN(4, 30, 1, 0xF0, 0x41C), + MX53_PIN_CSI0_D13 = _MXC_BUILD_GPIO_PIN(4, 31, 1, 0xF4, 0x420), + MX53_PIN_CSI0_D14 = _MXC_BUILD_GPIO_PIN(5, 0, 1, 0xF8, 0x424), + MX53_PIN_CSI0_D15 = _MXC_BUILD_GPIO_PIN(5, 1, 1, 0xFC, 0x428), + MX53_PIN_CSI0_D16 = _MXC_BUILD_GPIO_PIN(5, 2, 1, 0x100, 0x42C), + MX53_PIN_CSI0_D17 = _MXC_BUILD_GPIO_PIN(5, 3, 1, 0x104, 0x430), + MX53_PIN_CSI0_D18 = _MXC_BUILD_GPIO_PIN(5, 4, 1, 0x108, 0x434), + MX53_PIN_CSI0_D19 = _MXC_BUILD_GPIO_PIN(5, 5, 1, 0x10C, 0x438), + MX53_PIN_NVCC_CSI0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x43C), + MX53_PIN_JTAG_TMS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x440), + MX53_PIN_JTAG_MOD = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x444), + MX53_PIN_JTAG_TRSTB = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x448), + MX53_PIN_JTAG_TDI = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x44C), + MX53_PIN_JTAG_TCK = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x450), + MX53_PIN_JTAG_TDO = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x454), + MX53_PIN_EIM_A25 = _MXC_BUILD_GPIO_PIN(4, 2, 1, 0x110, 0x458), + MX53_PIN_EIM_EB2 = _MXC_BUILD_GPIO_PIN(1, 30, 1, 0x114, 0x45C), + MX53_PIN_EIM_D16 = _MXC_BUILD_GPIO_PIN(2, 16, 1, 0x118, 0x460), + MX53_PIN_EIM_D17 = _MXC_BUILD_GPIO_PIN(2, 17, 1, 0x11C, 0x464), + MX53_PIN_EIM_D18 = _MXC_BUILD_GPIO_PIN(2, 18, 1, 0x120, 0x468), + MX53_PIN_EIM_D19 = _MXC_BUILD_GPIO_PIN(2, 19, 1, 0x124, 0x46C), + MX53_PIN_EIM_D20 = _MXC_BUILD_GPIO_PIN(2, 20, 1, 0x128, 0x470), + MX53_PIN_EIM_D21 = _MXC_BUILD_GPIO_PIN(2, 21, 1, 0x12C, 0x474), + MX53_PIN_EIM_D22 = _MXC_BUILD_GPIO_PIN(2, 22, 1, 0x130, 0x478), + MX53_PIN_EIM_D23 = _MXC_BUILD_GPIO_PIN(2, 23, 1, 0x134, 0x47C), + MX53_PIN_EIM_EB3 = _MXC_BUILD_GPIO_PIN(1, 31, 1, 0x138, 0x480), + MX53_PIN_EIM_D24 = _MXC_BUILD_GPIO_PIN(2, 24, 1, 0x13C, 0x484), + MX53_PIN_EIM_D25 = _MXC_BUILD_GPIO_PIN(2, 25, 1, 0x140, 0x488), + MX53_PIN_EIM_D26 = _MXC_BUILD_GPIO_PIN(2, 26, 1, 0x144, 0x48C), + MX53_PIN_EIM_D27 = _MXC_BUILD_GPIO_PIN(2, 27, 1, 0x148, 0x490), + MX53_PIN_EIM_D28 = _MXC_BUILD_GPIO_PIN(2, 28, 1, 0x14C, 0x494), + MX53_PIN_EIM_D29 = _MXC_BUILD_GPIO_PIN(2, 29, 1, 0x150, 0x498), + MX53_PIN_EIM_D30 = _MXC_BUILD_GPIO_PIN(2, 30, 1, 0x154, 0x49C), + MX53_PIN_EIM_D31 = _MXC_BUILD_GPIO_PIN(2, 31, 1, 0x158, 0x4A0), + MX53_PIN_NVCC_EIM1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x4A4), + MX53_PIN_EIM_A24 = _MXC_BUILD_GPIO_PIN(4, 4, 1, 0x15C, 0x4A8), + MX53_PIN_EIM_A23 = _MXC_BUILD_GPIO_PIN(5, 6, 1, 0x160, 0x4AC), + MX53_PIN_EIM_A22 = _MXC_BUILD_GPIO_PIN(1, 16, 1, 0x164, 0x4B0), + MX53_PIN_EIM_A21 = _MXC_BUILD_GPIO_PIN(1, 17, 1, 0x168, 0x4B4), + MX53_PIN_EIM_A20 = _MXC_BUILD_GPIO_PIN(1, 18, 1, 0x16C, 0x4B8), + MX53_PIN_EIM_A19 = _MXC_BUILD_GPIO_PIN(1, 19, 1, 0x170, 0x4BC), + MX53_PIN_EIM_A18 = _MXC_BUILD_GPIO_PIN(1, 20, 1, 0x174, 0x4C0), + MX53_PIN_EIM_A17 = _MXC_BUILD_GPIO_PIN(1, 21, 1, 0x178, 0x4C4), + MX53_PIN_EIM_A16 = _MXC_BUILD_GPIO_PIN(1, 22, 1, 0x17C, 0x4C8), + MX53_PIN_EIM_CS0 = _MXC_BUILD_GPIO_PIN(1, 23, 1, 0x180, 0x4CC), + MX53_PIN_EIM_CS1 = _MXC_BUILD_GPIO_PIN(1, 24, 1, 0x184, 0x4D0), + MX53_PIN_EIM_OE = _MXC_BUILD_GPIO_PIN(1, 25, 1, 0x188, 0x4D4), + MX53_PIN_EIM_RW = _MXC_BUILD_GPIO_PIN(1, 26, 1, 0x18C, 0x4D8), + MX53_PIN_EIM_LBA = _MXC_BUILD_GPIO_PIN(1, 27, 1, 0x190, 0x4DC), + MX53_PIN_NVCC_EIM4 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x4E0), + MX53_PIN_EIM_EB0 = _MXC_BUILD_GPIO_PIN(1, 28, 1, 0x194, 0x4E4), + MX53_PIN_EIM_EB1 = _MXC_BUILD_GPIO_PIN(1, 29, 1, 0x198, 0x4E8), + MX53_PIN_EIM_DA0 = _MXC_BUILD_GPIO_PIN(2, 0, 1, 0x19C, 0x4EC), + MX53_PIN_EIM_DA1 = _MXC_BUILD_GPIO_PIN(2, 1, 1, 0x1A0, 0x4F0), + MX53_PIN_EIM_DA2 = _MXC_BUILD_GPIO_PIN(2, 2, 1, 0x1A4, 0x4F4), + MX53_PIN_EIM_DA3 = _MXC_BUILD_GPIO_PIN(2, 3, 1, 0x1A8, 0x4F8), + MX53_PIN_EIM_DA4 = _MXC_BUILD_GPIO_PIN(2, 4, 1, 0x1AC, 0x4FC), + MX53_PIN_EIM_DA5 = _MXC_BUILD_GPIO_PIN(2, 5, 1, 0x1B0, 0x500), + MX53_PIN_EIM_DA6 = _MXC_BUILD_GPIO_PIN(2, 6, 1, 0x1B4, 0x504), + MX53_PIN_EIM_DA7 = _MXC_BUILD_GPIO_PIN(2, 7, 1, 0x1B8, 0x508), + MX53_PIN_EIM_DA8 = _MXC_BUILD_GPIO_PIN(2, 8, 1, 0x1BC, 0x50C), + MX53_PIN_EIM_DA9 = _MXC_BUILD_GPIO_PIN(2, 9, 1, 0x1C0, 0x510), + MX53_PIN_EIM_DA10 = _MXC_BUILD_GPIO_PIN(2, 10, 1, 0x1C4, 0x514), + MX53_PIN_EIM_DA11 = _MXC_BUILD_GPIO_PIN(2, 11, 1, 0x1C8, 0x518), + MX53_PIN_EIM_DA12 = _MXC_BUILD_GPIO_PIN(2, 12, 1, 0x1CC, 0x51C), + MX53_PIN_EIM_DA13 = _MXC_BUILD_GPIO_PIN(2, 13, 1, 0x1D0, 0x520), + MX53_PIN_EIM_DA14 = _MXC_BUILD_GPIO_PIN(2, 14, 1, 0x1D4, 0x524), + MX53_PIN_EIM_DA15 = _MXC_BUILD_GPIO_PIN(2, 15, 1, 0x1D8, 0x528), + MX53_PIN_NANDF_WE_B = _MXC_BUILD_GPIO_PIN(5, 12, 1, 0x1DC, 0x52C), + MX53_PIN_NANDF_RE_B = _MXC_BUILD_GPIO_PIN(5, 13, 1, 0x1E0, 0x530), + MX53_PIN_EIM_WAIT = _MXC_BUILD_GPIO_PIN(4, 0, 1, 0x1E4, 0x534), + MX53_PIN_EIM_BCLK = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x538), + MX53_PIN_NVCC_EIM7 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x53C), + MX53_PIN_LVDS1_TX3_P = _MXC_BUILD_GPIO_PIN(5, 22, 0, 0x1EC, NON_PAD_I), + MX53_PIN_LVDS1_TX2_P = _MXC_BUILD_GPIO_PIN(5, 24, 0, 0x1F0, NON_PAD_I), + MX53_PIN_LVDS1_CLK_P = _MXC_BUILD_GPIO_PIN(5, 26, 0, 0x1F4, NON_PAD_I), + MX53_PIN_LVDS1_TX1_P = _MXC_BUILD_GPIO_PIN(5, 28, 0, 0x1F8, NON_PAD_I), + MX53_PIN_LVDS1_TX0_P = _MXC_BUILD_GPIO_PIN(5, 30, 0, 0x1FC, NON_PAD_I), + MX53_PIN_LVDS0_TX3_P = _MXC_BUILD_GPIO_PIN(6, 22, 0, 0x200, NON_PAD_I), + MX53_PIN_LVDS0_CLK_P = _MXC_BUILD_GPIO_PIN(6, 24, 0, 0x204, NON_PAD_I), + MX53_PIN_LVDS0_TX2_P = _MXC_BUILD_GPIO_PIN(6, 26, 0, 0x208, NON_PAD_I), + MX53_PIN_LVDS0_TX1_P = _MXC_BUILD_GPIO_PIN(6, 28, 0, 0x20C, NON_PAD_I), + MX53_PIN_LVDS0_TX0_P = _MXC_BUILD_GPIO_PIN(6, 30, 0, 0x210, NON_PAD_I), + MX53_PIN_GPIO_10 = _MXC_BUILD_GPIO_PIN(3, 0, 0, 0x214, 0x540), + MX53_PIN_GPIO_11 = _MXC_BUILD_GPIO_PIN(3, 1, 0, 0x218, 0x544), + MX53_PIN_GPIO_12 = _MXC_BUILD_GPIO_PIN(3, 2, 0, 0x21C, 0x548), + MX53_PIN_GPIO_13 = _MXC_BUILD_GPIO_PIN(3, 3, 0, 0x220, 0x54C), + MX53_PIN_GPIO_14 = _MXC_BUILD_GPIO_PIN(3, 4, 0, 0x224, 0x550), + MX53_PIN_DRAM_DQM3 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x554), + MX53_PIN_DRAM_SDQS3 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x558), + MX53_PIN_DRAM_SDCKE1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x55C), + MX53_PIN_DRAM_DQM2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x560), + MX53_PIN_DRAM_SDODT1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x564), + MX53_PIN_DRAM_SDQS2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x568), + MX53_PIN_DRAM_RESET = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x56C), + MX53_PIN_DRAM_SDCLK1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x570), + MX53_PIN_DRAM_CAS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x574), + MX53_PIN_DRAM_SDCLK0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x578), + MX53_PIN_DRAM_SDQS0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x57C), + MX53_PIN_DRAM_SDODT0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x580), + MX53_PIN_DRAM_DQM0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x584), + MX53_PIN_DRAM_RAS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x588), + MX53_PIN_DRAM_SDCKE0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x58C), + MX53_PIN_DRAM_SDQS1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x590), + MX53_PIN_DRAM_DQM1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x594), + MX53_PIN_PMIC_ON_REQ = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x598), + MX53_PIN_PMIC_STBY_REQ = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x59C), + MX53_PIN_NANDF_CLE = _MXC_BUILD_GPIO_PIN(5, 7, 1, 0x228, 0x5A0), + MX53_PIN_NANDF_ALE = _MXC_BUILD_GPIO_PIN(5, 8 , 1, 0x22C, 0x5A4), + MX53_PIN_NANDF_WP_B = _MXC_BUILD_GPIO_PIN(5, 9, 1, 0x230, 0x5A8), + MX53_PIN_NANDF_RB0 = _MXC_BUILD_GPIO_PIN(5, 10, 1, 0x234, 0x5AC), + MX53_PIN_NANDF_CS0 = _MXC_BUILD_GPIO_PIN(5, 11, 1, 0x238, 0x5B0), + MX53_PIN_NANDF_CS1 = _MXC_BUILD_GPIO_PIN(5, 14, 1, 0x23C, 0x5B4), + MX53_PIN_NANDF_CS2 = _MXC_BUILD_GPIO_PIN(5, 15, 1, 0x240, 0x5B8), + MX53_PIN_NANDF_CS3 = _MXC_BUILD_GPIO_PIN(5, 16, 1, 0x244, 0x5BC), + MX53_PIN_NVCC_NANDF = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x5C0), + MX53_PIN_FEC_MDIO = _MXC_BUILD_GPIO_PIN(0, 22, 1, 0x248, 0x5C4), + MX53_PIN_FEC_REF_CLK = _MXC_BUILD_GPIO_PIN(0, 23, 1, 0x24C, 0x5C8), + MX53_PIN_FEC_RX_ER = _MXC_BUILD_GPIO_PIN(0, 24, 1, 0x250, 0x5CC), + MX53_PIN_FEC_CRS_DV = _MXC_BUILD_GPIO_PIN(0, 25, 1, 0x254, 0x5D0), + MX53_PIN_FEC_RXD1 = _MXC_BUILD_GPIO_PIN(0, 26, 1, 0x258, 0x5D4), + MX53_PIN_FEC_RXD0 = _MXC_BUILD_GPIO_PIN(0, 27, 1, 0x25C, 0x5D8), + MX53_PIN_FEC_TX_EN = _MXC_BUILD_GPIO_PIN(0, 28, 1, 0x260, 0x5DC), + MX53_PIN_FEC_TXD1 = _MXC_BUILD_GPIO_PIN(0, 29, 1, 0x264, 0x5E0), + MX53_PIN_FEC_TXD0 = _MXC_BUILD_GPIO_PIN(0, 30, 1, 0x268, 0x5E4), + MX53_PIN_FEC_MDC = _MXC_BUILD_GPIO_PIN(0, 31, 1, 0x26C, 0x5E8), + MX53_PIN_NVCC_FEC = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x5EC), + MX53_PIN_ATA_DIOW = _MXC_BUILD_GPIO_PIN(5, 17, 1, 0x270, 0x5F0), + MX53_PIN_ATA_DMACK = _MXC_BUILD_GPIO_PIN(5, 18, 1, 0x274, 0x5F4), + MX53_PIN_ATA_DMARQ = _MXC_BUILD_GPIO_PIN(6, 0, 1, 0x278, 0x5F8), + MX53_PIN_ATA_BUFFER_EN = _MXC_BUILD_GPIO_PIN(6, 1, 1, 0x27C, 0x5FC), + MX53_PIN_ATA_INTRQ = _MXC_BUILD_GPIO_PIN(6, 2, 1, 0x280, 0x600), + MX53_PIN_ATA_DIOR = _MXC_BUILD_GPIO_PIN(6, 3, 1, 0x284, 0x604), + MX53_PIN_ATA_RESET_B = _MXC_BUILD_GPIO_PIN(6, 4, 1, 0x288, 0x608), + MX53_PIN_ATA_IORDY = _MXC_BUILD_GPIO_PIN(6, 5, 1, 0x28C, 0x60C), + MX53_PIN_ATA_DA_0 = _MXC_BUILD_GPIO_PIN(6, 6, 1, 0x290, 0x610), + MX53_PIN_ATA_DA_1 = _MXC_BUILD_GPIO_PIN(6, 7, 1, 0x294, 0x614), + MX53_PIN_ATA_DA_2 = _MXC_BUILD_GPIO_PIN(6, 8, 1, 0x298, 0x618), + MX53_PIN_ATA_CS_0 = _MXC_BUILD_GPIO_PIN(6, 9, 1, 0x29C, 0x61C), + MX53_PIN_ATA_CS_1 = _MXC_BUILD_GPIO_PIN(6, 10, 1, 0x2A0, 0x620), + MX53_PIN_NVCC_ATA2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x624), + MX53_PIN_ATA_DATA0 = _MXC_BUILD_GPIO_PIN(1, 0, 1, 0x2A4, 0x628), + MX53_PIN_ATA_DATA1 = _MXC_BUILD_GPIO_PIN(1, 1, 1, 0x2A8, 0x62C), + MX53_PIN_ATA_DATA2 = _MXC_BUILD_GPIO_PIN(1, 2, 1, 0x2AC, 0x630), + MX53_PIN_ATA_DATA3 = _MXC_BUILD_GPIO_PIN(1, 3, 1, 0x2B0, 0x634), + MX53_PIN_ATA_DATA4 = _MXC_BUILD_GPIO_PIN(1, 4, 1, 0x2B4, 0x638), + MX53_PIN_ATA_DATA5 = _MXC_BUILD_GPIO_PIN(1, 5, 1, 0x2B8, 0x63C), + MX53_PIN_ATA_DATA6 = _MXC_BUILD_GPIO_PIN(1, 6, 1, 0x2BC, 0x640), + MX53_PIN_ATA_DATA7 = _MXC_BUILD_GPIO_PIN(1, 7, 1, 0x2C0, 0x644), + MX53_PIN_ATA_DATA8 = _MXC_BUILD_GPIO_PIN(1, 8, 1, 0x2C4, 0x648), + MX53_PIN_ATA_DATA9 = _MXC_BUILD_GPIO_PIN(1, 9, 1, 0x2C8, 0x64C), + MX53_PIN_ATA_DATA10 = _MXC_BUILD_GPIO_PIN(1, 10, 1, 0x2CC, 0x650), + MX53_PIN_ATA_DATA11 = _MXC_BUILD_GPIO_PIN(1, 11, 1, 0x2D0, 0x654), + MX53_PIN_ATA_DATA12 = _MXC_BUILD_GPIO_PIN(1, 12, 1, 0x2D4, 0x658), + MX53_PIN_ATA_DATA13 = _MXC_BUILD_GPIO_PIN(1, 13, 1, 0x2D8, 0x65C), + MX53_PIN_ATA_DATA14 = _MXC_BUILD_GPIO_PIN(1, 14, 1, 0x2DC, 0x660), + MX53_PIN_ATA_DATA15 = _MXC_BUILD_GPIO_PIN(1, 15, 1, 0x2E0, 0x664), + MX53_PIN_NVCC_ATA0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x668), + MX53_PIN_SD1_DATA0 = _MXC_BUILD_GPIO_PIN(0, 16, 1, 0x2E4, 0x66C), + MX53_PIN_SD1_DATA1 = _MXC_BUILD_GPIO_PIN(0, 17, 1, 0x2E8, 0x670), + MX53_PIN_SD1_CMD = _MXC_BUILD_GPIO_PIN(0, 18, 1, 0x2EC, 0x674), + MX53_PIN_SD1_DATA2 = _MXC_BUILD_GPIO_PIN(0, 19, 1, 0x2F0, 0x678), + MX53_PIN_SD1_CLK = _MXC_BUILD_GPIO_PIN(0, 20, 1, 0x2F4, 0x67C), + MX53_PIN_SD1_DATA3 = _MXC_BUILD_GPIO_PIN(0, 21, 1, 0x2F8, 0x680), + MX53_PIN_NVCC_SD1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x684), + MX53_PIN_SD2_CLK = _MXC_BUILD_GPIO_PIN(0, 10, 1, 0x2FC, 0x688), + MX53_PIN_SD2_CMD = _MXC_BUILD_GPIO_PIN(0, 11, 1, 0x300, 0x68C), + MX53_PIN_SD2_DATA3 = _MXC_BUILD_GPIO_PIN(0, 12, 1, 0x304, 0x690), + MX53_PIN_SD2_DATA2 = _MXC_BUILD_GPIO_PIN(0, 13, 1, 0x308, 0x694), + MX53_PIN_SD2_DATA1 = _MXC_BUILD_GPIO_PIN(0, 14, 1, 0x30C, 0x698), + MX53_PIN_SD2_DATA0 = _MXC_BUILD_GPIO_PIN(0, 15, 1, 0x310, 0x69C), + MX53_PIN_NVCC_SD2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6A0), + MX53_PIN_GPIO_0 = _MXC_BUILD_GPIO_PIN(0, 0, 1, 0x314, 0x6A4), + MX53_PIN_GPIO_1 = _MXC_BUILD_GPIO_PIN(0, 1, 1, 0x318, 0x6A8), + MX53_PIN_GPIO_9 = _MXC_BUILD_GPIO_PIN(0, 9, 1, 0x31C, 0x6AC), + MX53_PIN_GPIO_3 = _MXC_BUILD_GPIO_PIN(0, 3, 1, 0x320, 0x6B0), + MX53_PIN_GPIO_6 = _MXC_BUILD_GPIO_PIN(0, 6, 1, 0x324, 0x6B4), + MX53_PIN_GPIO_2 = _MXC_BUILD_GPIO_PIN(0, 2, 1, 0x328, 0x6B8), + MX53_PIN_GPIO_4 = _MXC_BUILD_GPIO_PIN(0, 4, 1, 0x32C, 0x6BC), + MX53_PIN_GPIO_5 = _MXC_BUILD_GPIO_PIN(0, 5, 1, 0x330, 0x6C0), + MX53_PIN_GPIO_7 = _MXC_BUILD_GPIO_PIN(0, 7, 1, 0x334, 0x6C4), + MX53_PIN_GPIO_8 = _MXC_BUILD_GPIO_PIN(0, 8, 1, 0x338, 0x6C8), + MX53_PIN_GPIO_16 = _MXC_BUILD_GPIO_PIN(6, 11, 1, 0x33C, 0x6CC), + MX53_PIN_GPIO_17 = _MXC_BUILD_GPIO_PIN(6, 12, 1, 0x340, 0x6D0), + MX53_PIN_GPIO_18 = _MXC_BUILD_GPIO_PIN(6, 13, 1, 0x344, 0x6D4), + MX53_PIN_NVCC_GPIO = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6D8), + MX53_PIN_POR_B = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6DC), + MX53_PIN_BOOT_MODE1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6E0), + MX53_PIN_RESET_IN_B = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6E4), + MX53_PIN_BOOT_MODE0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6E8), + MX53_PIN_TEST_MODE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6EC), + MX53_PIN_GRP_ADDDS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6F0), + MX53_PIN_GRP_DDRMODE_CTL = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6F4), + MX53_PIN_GRP_DDRPKE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6FC), + MX53_PIN_GRP_DDRPK = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x708), + MX53_PIN_GRP_TERM_CTL3 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x70C), + MX53_PIN_GRP_DDRHYS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x710), + MX53_PIN_GRP_DDRMODE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x714), + MX53_PIN_GRP_B0DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x718), + MX53_PIN_GRP_B1DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x71C), + MX53_PIN_GRP_CTLDS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x720), + MX53_PIN_GRP_DDR_TYPE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x724), + MX53_PIN_GRP_B2DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x728), + MX53_PIN_GRP_B3DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x72C), +}; +/* various IOMUX input select register index */ +typedef enum iomux_input_select { + MX51_AUDMUX_P4_INPUT_DA_AMX_SELECT_I = 0, + MX51_AUDMUX_P4_INPUT_DB_AMX_SELECT_I, + MX51_AUDMUX_P4_INPUT_TXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P4_INPUT_TXFS_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_DA_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_DB_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_RXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_RXFS_AMX_SELECT, + MX51_AUDMUX_P5_INPUT_TXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_TXFS_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_DA_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_DB_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_RXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_RXFS_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_TXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_TXFS_AMX_SELECT_INPUT, + MX51_CCM_IPP_DI_CLK_SELECT_INPUT, + /* TO2 */ + MX51_CCM_IPP_DI1_CLK_SELECT_INPUT, + MX51_CCM_PLL1_BYPASS_CLK_SELECT_INPUT, + MX51_CCM_PLL2_BYPASS_CLK_SELECT_INPUT, + MX51_CSPI_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX51_CSPI_IPP_IND_MISO_SELECT_INPUT, + MX51_CSPI_IPP_IND_MOSI_SELECT_INPUT, + MX51_CSPI_IPP_IND_SS_B_1_SELECT_INPUT, + MX51_CSPI_IPP_IND_SS_B_2_SELECT_INPUT, + MX51_CSPI_IPP_IND_SS_B_3_SELECT_INPUT, + MX51_DPLLIP1_L1T_TOG_EN_SELECT_INPUT, + /* TO2 */ + MX51_ECSPI2_IPP_IND_SS_B_1_SELECT_INPUT, + MX51_ECSPI2_IPP_IND_SS_B_3_SELECT_INPUT, + MX51_EMI_IPP_IND_RDY_INT_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT0_IN_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT1_IN_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT2_IN_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT3_IN_SELECT_INPUT, + MX51_FEC_FEC_COL_SELECT_INPUT, + MX51_FEC_FEC_CRS_SELECT_INPUT, + MX51_FEC_FEC_MDI_SELECT_INPUT, + MX51_FEC_FEC_RDATA_0_SELECT_INPUT, + MX51_FEC_FEC_RDATA_1_SELECT_INPUT, + MX51_FEC_FEC_RDATA_2_SELECT_INPUT, + MX51_FEC_FEC_RDATA_3_SELECT_INPUT, + MX51_FEC_FEC_RX_CLK_SELECT_INPUT, + MX51_FEC_FEC_RX_DV_SELECT_INPUT, + MX51_FEC_FEC_RX_ER_SELECT_INPUT, + MX51_FEC_FEC_TX_CLK_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_1_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_2_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_3_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_5_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_6_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_7_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_8_SELECT_INPUT, + /* TO2 */ + MX51_GPIO3_IPP_IND_G_IN_12_SELECT_INPUT, + MX51_HSC_MIPI_MIX_IPP_IND_SENS1_DATA_EN_SELECT_INPUT, + MX51_HSC_MIPI_MIX_IPP_IND_SENS2_DATA_EN_SELECT_INPUT, + /* TO2 */ + MX51_HSC_MIPI_MIX_PAR_VSYNC_SELECT_INPUT, + /* TO2 */ + MX51_HSC_MIPI_MIX_PAR_DI_WAIT_SELECT_INPUT, + MX51_HSC_MIPI_MIX_PAR_SISG_TRIG_SELECT_INPUT, + MX51_I2C1_IPP_SCL_IN_SELECT_INPUT, + MX51_I2C1_IPP_SDA_IN_SELECT_INPUT, + MX51_I2C2_IPP_SCL_IN_SELECT_INPUT, + MX51_I2C2_IPP_SDA_IN_SELECT_INPUT, + MX51_IPU_IPP_DI_0_IND_DISPB_SD_D_SELECT_INPUT, + MX51_IPU_IPP_DI_1_IND_DISPB_SD_D_SELECT_INPUT, + MX51_KPP_IPP_IND_COL_6_SELECT_INPUT, + MX51_KPP_IPP_IND_COL_7_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_4_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_5_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_6_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_7_SELECT_INPUT, + MX51_UART1_IPP_UART_RTS_B_SELECT_INPUT, + MX51_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, + MX51_UART2_IPP_UART_RTS_B_SELECT_INPUT, + MX51_UART2_IPP_UART_RXD_MUX_SELECT_INPUT, + MX51_UART3_IPP_UART_RTS_B_SELECT_INPUT, + MX51_UART3_IPP_UART_RXD_MUX_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_CLK_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_0_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_1_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_2_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_3_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_4_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_5_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_6_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_7_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DIR_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_NXT_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_STP_SELECT_INPUT, + MX51PUT_NUM_MUX, + /* MX53 */ + MX53_AUDMUX_P4_INPUT_DA_AMX_SELECT_I = 0, + MX53_AUDMUX_P4_INPUT_DB_AMX_SELECT_I, + MX53_AUDMUX_P4_INPUT_RXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P4_INPUT_RXFS_AMX_SELECT_INPUT, + MX53_AUDMUX_P4_INPUT_TXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P4_INPUT_TXFS_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_DA_AMX_SELECT_I, + MX53_AUDMUX_P5_INPUT_DB_AMX_SELECT_I, + MX53_AUDMUX_P5_INPUT_RXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_RXFS_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_TXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_TXFS_AMX_SELECT_INPUT, + MX53_CAN1_IPP_IND_CANRX_SELECT_INPUT, + MX53_CAN2_IPP_IND_CANRX_SELECT_INPUT, + MX53_CCM_IPP_ASRC_EXT_SELECT_INPUT, + MX53_CCM_IPP_DI1_CLK_SELECT_INPUT, + MX53_CCM_PLL1_BYPASS_CLK_SELECT_INPUT, + MX53_CCM_PLL2_BYPASS_CLK_SELECT_INPUT, + MX53_CCM_PLL3_BYPASS_CLK_SELECT_INPUT, + MX53_CCM_PLL4_BYPASS_CLK_SELECT_INPUT, + MX53_CSPI_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX53_CSPI_IPP_IND_MISO_SELECT_INPUT, + MX53_CSPI_IPP_IND_MOSI_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_1_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_2_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_3_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_4_SELECT_INPUT, + MX53_ECSPI1_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_MISO_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_MOSI_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_1_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_2_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_3_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_4_SELECT_INPUT, + MX53_ECSPI2_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_MISO_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_MOSI_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_SS_B_1_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_SS_B_2_SELECT_INPUT, + MX53_ESAI1_IPP_IND_FSR_SELECT_INPUT, + MX53_ESAI1_IPP_IND_FST_SELECT_INPUT, + MX53_ESAI1_IPP_IND_HCKR_SELECT_INPUT, + MX53_ESAI1_IPP_IND_HCKT_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SCKR_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SCKT_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO0_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO1_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO2_SDI3_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO3_SDI2_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO4_SDI1_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO5_SDI0_SELECT_INPUT, + MX53_ESDHC1_IPP_WP_ON_SELECT_INPUT, + MX53_FEC_FEC_COL_SELECT_INPUT, + MX53_FEC_FEC_MDI_SELECT_INPUT, + MX53_FEC_FEC_RX_CLK_SELECT_INPUT, + MX53_FIRI_IPP_IND_RXD_SELECT_INPUT, + MX53_GPC_PMIC_RDY_SELECT_INPUT, + MX53_I2C1_IPP_SCL_IN_SELECT_INPUT, + MX53_I2C1_IPP_SDA_IN_SELECT_INPUT, + MX53_I2C2_IPP_SCL_IN_SELECT_INPUT, + MX53_I2C2_IPP_SDA_IN_SELECT_INPUT, + MX53_I2C3_IPP_SCL_IN_SELECT_INPUT, + MX53_I2C3_IPP_SDA_IN_SELECT_INPUT, + MX53_IPU_IPP_DI_0_IND_DISPB_SD_D_SELECT_INPUT, + MX53_IPU_IPP_DI_1_IND_DISPB_SD_D_SELECT_INPUT, + MX53_IPU_IPP_IND_SENS1_DATA_EN_SELECT_INPUT, + MX53_IPU_IPP_IND_SENS1_HSYNC_SELECT_INPUT, + MX53_IPU_IPP_IND_SENS1_VSYNC_SELECT_INPUT, + MX53_KPP_IPP_IND_COL_5_SELECT_INPUT, + MX53_KPP_IPP_IND_COL_6_SELECT_INPUT, + MX53_KPP_IPP_IND_COL_7_SELECT_INPUT, + MX53_KPP_IPP_IND_ROW_5_SELECT_INPUT, + MX53_KPP_IPP_IND_ROW_6_SELECT_INPUT, + MX53_KPP_IPP_IND_ROW_7_SELECT_INPUT, + MX53_MLB_MLBCLK_IN_SELECT_INPUT, + MX53_MLB_MLBDAT_IN_SELECT_INPUT, + MX53_MLB_MLBSIG_IN_SELECT_INPUT, + MX53_OWIRE_BATTERY_LINE_IN_SELECT_INPUT, + MX53_SDMA_EVENTS_14_SELECT_INPUT, + MX53_SDMA_EVENTS_15_SELECT_INPUT, + MX53_SPDIF_SPDIF_IN1_SELECT_INPUT, + MX53_UART1_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART2_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART2_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART3_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART3_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART4_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART4_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART5_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART5_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_USBOH3_IPP_IND_OTG_OC_SELECT_INPUT, + MX53_USBOH3_IPP_IND_UH1_OC_SELECT_INPUT, + MX53_USBOH3_IPP_IND_UH2_OC_SELECT_INPUT, +} iomux_input_select_t; + #endif /* __ASSEMBLY__ */ #endif /* __ASM_ARCH_MX5_MX5X_PINS_H__ */ diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h old mode 100644 new mode 100755 index b4e5738..3d6d390 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -24,8 +24,6 @@ #ifndef __CONFIG_H #define __CONFIG_H
-#include <asm/arch/imx-regs.h> - /* High Level Configuration Options */
#define CONFIG_MX51 /* in a mx51 */ @@ -37,6 +35,7 @@
#define CONFIG_L2_OFF
+#include <asm/arch/imx-regs.h> /* * Disabled for now due to build problems under Debian and a significant * increase in the final file size: 144260 vs. 109536 Bytes. diff --git a/include/configs/vision2.h b/include/configs/vision2.h index a5c116b..4c8e7fa 100644 --- a/include/configs/vision2.h +++ b/include/configs/vision2.h @@ -24,11 +24,12 @@ #ifndef __CONFIG_H #define __CONFIG_H
-#include <asm/arch/imx-regs.h>
#define CONFIG_MX51 /* in a mx51 */ #define CONFIG_L2_OFF
+#include <asm/arch/imx-regs.h> + #define CONFIG_SYS_MX5_HCLK 24000000 #define CONFIG_SYS_MX5_CLK32 32768 #define CONFIG_DISPLAY_CPUINFO
This patch add I2C support for Freescale MX53 processor
Signed-off-by: Jason Liu r64343@freescale.com
--- Changes for v2: -address the comments of Heiko, add #if defined(CONFIG_MX31) to avoid break MX31 build. Move CONFIG_HARD_I2C to the top of the file and fix the error message from: #error "define CONFIG_SYS_I2C_PORT to use the I2C driver" to #error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver" --- drivers/i2c/mxc_i2c.c | 19 +++++++++++++++++-- 1 files changed, 17 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c old mode 100644 new mode 100755 index 8e10fbb..95d27ae --- a/drivers/i2c/mxc_i2c.c +++ b/drivers/i2c/mxc_i2c.c @@ -26,8 +26,14 @@
#if defined(CONFIG_HARD_I2C)
+#ifdef CONFIG_MX31 #include <asm/arch/mx31.h> #include <asm/arch/mx31-regs.h> +#endif + +#if defined(CONFIG_MX53) +#include <asm/arch/clock.h> +#endif
#define IADR 0x00 #define IFDR 0x04 @@ -56,8 +62,12 @@ #elif defined (CONFIG_SYS_I2C_MX31_PORT3) #define I2C_BASE 0x43f84000 #define I2C_CLK_OFFSET 30 +#elif defined(CONFIG_SYS_I2C_MX53_PORT1) +#define I2C_BASE I2C1_BASE_ADDR +#elif defined(CONFIG_SYS_I2C_MX53_PORT2) +#define I2C_BASE I2C2_BASE_ADDR #else -#error "define CONFIG_SYS_I2C_MX31_PORTx to use the mx31 I2C driver" +#error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver" #endif
#ifdef DEBUG @@ -72,11 +82,16 @@ static u16 div[] = { 30, 32, 36, 42, 48, 52, 60, 72, 80, 88, 104, 128, 144,
void i2c_init(int speed, int unused) { - int freq = mx31_get_ipg_clk(); + int freq; int i;
+#ifdef CONFIG_MX31 + freq = mx31_get_ipg_clk(); /* start the required I2C clock */ __REG(CCM_CGR0) = __REG(CCM_CGR0) | (3 << I2C_CLK_OFFSET); +#else + freq = mxc_get_clock(MXC_IPG_PERCLK); +#endif
for (i = 0; i < 0x1f; i++) if (freq / div[i] <= speed)
Le 22/12/2010 14:23, Jason Liu a écrit :
This patch add I2C support for Freescale MX53 processor
Signed-off-by: Jason Liur64343@freescale.com
Changes for v2: -address the comments of Heiko, add #if defined(CONFIG_MX31) to avoid break MX31 build. Move CONFIG_HARD_I2C to the top of the file and fix the error message from: #error "define CONFIG_SYS_I2C_PORT to use the I2C driver" to #error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver"
drivers/i2c/mxc_i2c.c | 19 +++++++++++++++++-- 1 files changed, 17 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c old mode 100644 new mode 100755 index 8e10fbb..95d27ae --- a/drivers/i2c/mxc_i2c.c +++ b/drivers/i2c/mxc_i2c.c @@ -26,8 +26,14 @@
#if defined(CONFIG_HARD_I2C)
+#ifdef CONFIG_MX31
Can you make this an #if defined() like all others you are adding here?
#include<asm/arch/mx31.h> #include<asm/arch/mx31-regs.h> +#endif
+#if defined(CONFIG_MX53) +#include<asm/arch/clock.h> +#endif
#define IADR 0x00 #define IFDR 0x04 @@ -56,8 +62,12 @@ #elif defined (CONFIG_SYS_I2C_MX31_PORT3) #define I2C_BASE 0x43f84000 #define I2C_CLK_OFFSET 30 +#elif defined(CONFIG_SYS_I2C_MX53_PORT1) +#define I2C_BASE I2C1_BASE_ADDR +#elif defined(CONFIG_SYS_I2C_MX53_PORT2) +#define I2C_BASE I2C2_BASE_ADDR #else -#error "define CONFIG_SYS_I2C_MX31_PORTx to use the mx31 I2C driver" +#error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver" #endif
#ifdef DEBUG @@ -72,11 +82,16 @@ static u16 div[] = { 30, 32, 36, 42, 48, 52, 60, 72, 80, 88, 104, 128, 144,
void i2c_init(int speed, int unused) {
- int freq = mx31_get_ipg_clk();
- int freq; int i;
+#ifdef CONFIG_MX31
Ditto, for the sake of homogeneity.
- freq = mx31_get_ipg_clk(); /* start the required I2C clock */ __REG(CCM_CGR0) = __REG(CCM_CGR0) | (3<< I2C_CLK_OFFSET);
+#else
- freq = mxc_get_clock(MXC_IPG_PERCLK);
+#endif
for (i = 0; i< 0x1f; i++) if (freq / div[i]<= speed)
Amicalement,
Hi, Albert,
2010/12/23 Albert ARIBAUD albert.aribaud@free.fr:
Le 22/12/2010 14:23, Jason Liu a écrit :
This patch add I2C support for Freescale MX53 processor
Signed-off-by: Jason Liur64343@freescale.com
Changes for v2: -address the comments of Heiko, add #if defined(CONFIG_MX31) to avoid break MX31 build. Move CONFIG_HARD_I2C to the top of the file and fix the error message from: #error "define CONFIG_SYS_I2C_PORT to use the I2C driver" to #error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver"
drivers/i2c/mxc_i2c.c | 19 +++++++++++++++++-- 1 files changed, 17 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c old mode 100644 new mode 100755 index 8e10fbb..95d27ae --- a/drivers/i2c/mxc_i2c.c +++ b/drivers/i2c/mxc_i2c.c @@ -26,8 +26,14 @@
#if defined(CONFIG_HARD_I2C)
+#ifdef CONFIG_MX31
Can you make this an #if defined() like all others you are adding here?
OK, I will do it. Thanks,
#include<asm/arch/mx31.h> #include<asm/arch/mx31-regs.h> +#endif
+#if defined(CONFIG_MX53) +#include<asm/arch/clock.h> +#endif
#define IADR 0x00 #define IFDR 0x04 @@ -56,8 +62,12 @@ #elif defined (CONFIG_SYS_I2C_MX31_PORT3) #define I2C_BASE 0x43f84000 #define I2C_CLK_OFFSET 30 +#elif defined(CONFIG_SYS_I2C_MX53_PORT1) +#define I2C_BASE I2C1_BASE_ADDR +#elif defined(CONFIG_SYS_I2C_MX53_PORT2) +#define I2C_BASE I2C2_BASE_ADDR #else -#error "define CONFIG_SYS_I2C_MX31_PORTx to use the mx31 I2C driver" +#error "define CONFIG_SYS_I2C_MXxx_PORTx to use the I2C driver" #endif
#ifdef DEBUG @@ -72,11 +82,16 @@ static u16 div[] = { 30, 32, 36, 42, 48, 52, 60, 72, 80, 88, 104, 128, 144,
void i2c_init(int speed, int unused) {
- int freq = mx31_get_ipg_clk();
- int freq;
int i;
+#ifdef CONFIG_MX31
Ditto, for the sake of homogeneity.
- freq = mx31_get_ipg_clk();
/* start the required I2C clock */ __REG(CCM_CGR0) = __REG(CCM_CGR0) | (3<< I2C_CLK_OFFSET); +#else
- freq = mxc_get_clock(MXC_IPG_PERCLK);
+#endif
for (i = 0; i< 0x1f; i++) if (freq / div[i]<= speed)
Amicalement,
Albert. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Add initial support for MX53EVK board support. FEC, SD/MMC, UART, I2C, have been support.
Signed-off-by: Jason Liu r64343@freescale.com
--- Changes for v2: -Address the comments from Stefano, Albert and Wolfgang, -remove the ivt.S file and use imximage.cfg instead, -remove the ivt link to u-boot -Address the comments from Stefano, -Correct the copyright issue, -Use mxc_get_gpio() and mxc_set_gpio() accessors. -Get rid of system_rev, -use i2c enumeration value (0,1,..N) instead of BASE address, -use fsl_pmic i2c interface, -Add comments for why manage the pmic in a different way for TO2 -Remove the comments from configs/mx53evk.h, - /* - * Disabled for now due to build problems under Debian and a significant - * increase in the final file size: 144260 vs. 109536 Bytes. - */ -Address the comments from Wolfgang, -Move CONFIG_SYS_TEXT_BASE to board config file, -Remove the comments from configs/mx53evk.h - /* size in bytes reserved for initial data */ #define BOARD_LATE_INIT -Change the comments, * Hardware drivers to * UART drivers --- MAINTAINERS | 3 + board/freescale/mx53evk/Makefile | 48 +++++ board/freescale/mx53evk/mx53evk.c | 393 +++++++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/mx53evk.h | 216 ++++++++++++++++++++ 5 files changed, 661 insertions(+), 0 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS index 0590ad9..c87ca56 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1085,6 +1085,9 @@ Peter Meerwald devel@bct-electronic.com
bct-brettl2 BF536
+Jason Liu r64343@freescale.com + + MX53evk i.MX53 ######################################################################### # End of MAINTAINERS list # ######################################################################### diff --git a/board/freescale/mx53evk/Makefile b/board/freescale/mx53evk/Makefile new file mode 100755 index 0000000..6b820f4 --- /dev/null +++ b/board/freescale/mx53evk/Makefile @@ -0,0 +1,48 @@ +# +# Copyright (C) 2007, Guennadi Liakhovetski lg@denx.de +# +# (C) Copyright 2010 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := mx53evk.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c new file mode 100755 index 0000000..5f5a734 --- /dev/null +++ b/board/freescale/mx53evk/mx53evk.c @@ -0,0 +1,393 @@ +/* + * (C) Copyright 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx5x_pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/iomux.h> +#include <asm/errno.h> +#include <netdev.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <fsl_pmic.h> +#include <mxc_gpio.h> + +DECLARE_GLOBAL_DATA_PTR; + +u32 get_board_rev(void) +{ + return get_cpu_rev(); +} + +int dram_init(void) +{ + /* dram_init must store complete ramsize in gd->ram_size */ + gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE, + PHYS_SDRAM_1_SIZE); + return 0; +} + +static void setup_iomux_uart(void) +{ + /* UART1 RXD */ + mxc_request_iomux(MX53_PIN_CSI0_D11, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX53_PIN_CSI0_D11, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU | + PAD_CTL_ODE_OPENDRAIN_ENABLE); + mxc_iomux_set_input(MX53_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, 0x1); + + /* UART1 TXD */ + mxc_request_iomux(MX53_PIN_CSI0_D10, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX53_PIN_CSI0_D10, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU | + PAD_CTL_ODE_OPENDRAIN_ENABLE); +} + +#ifdef CONFIG_I2C_MXC +static void setup_i2c(unsigned int port_number) +{ + switch (port_number) { + case 0: + /* i2c1 SDA */ + mxc_request_iomux(MX53_PIN_CSI0_D8, + IOMUX_CONFIG_ALT5 | IOMUX_CONFIG_SION); + mxc_iomux_set_input(MX53_I2C1_IPP_SDA_IN_SELECT_INPUT, + INPUT_CTL_PATH0); + mxc_iomux_set_pad(MX53_PIN_CSI0_D8, + PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH | + PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE | + PAD_CTL_ODE_OPENDRAIN_ENABLE); + /* i2c1 SCL */ + mxc_request_iomux(MX53_PIN_CSI0_D9, + IOMUX_CONFIG_ALT5 | IOMUX_CONFIG_SION); + mxc_iomux_set_input(MX53_I2C1_IPP_SCL_IN_SELECT_INPUT, + INPUT_CTL_PATH0); + mxc_iomux_set_pad(MX53_PIN_CSI0_D9, + PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH | + PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE | + PAD_CTL_ODE_OPENDRAIN_ENABLE); + break; + case 1: + /* i2c2 SDA */ + mxc_request_iomux(MX53_PIN_KEY_ROW3, + IOMUX_CONFIG_ALT4 | IOMUX_CONFIG_SION); + mxc_iomux_set_input(MX53_I2C2_IPP_SDA_IN_SELECT_INPUT, + INPUT_CTL_PATH0); + mxc_iomux_set_pad(MX53_PIN_KEY_ROW3, + PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH | + PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE | + PAD_CTL_ODE_OPENDRAIN_ENABLE); + + /* i2c2 SCL */ + mxc_request_iomux(MX53_PIN_KEY_COL3, + IOMUX_CONFIG_ALT4 | IOMUX_CONFIG_SION); + mxc_iomux_set_input(MX53_I2C2_IPP_SCL_IN_SELECT_INPUT, + INPUT_CTL_PATH0); + mxc_iomux_set_pad(MX53_PIN_KEY_COL3, + PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH | + PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE | + PAD_CTL_ODE_OPENDRAIN_ENABLE); + break; + default: + printf("Warning: Wrong I2C port number\n"); + break; + } +} + +void power_init(void) +{ + unsigned int val; + + /* Set VDDA to 1.25V */ + val = pmic_reg_read(REG_SW_2); + val = (val & (~0x1F)) | 0x1A; + pmic_reg_write(REG_SW_2, val); + + /* + * Need increase VCC and VDDA to 1.3V + * according to MX53 IC TO2 datasheet. + */ + if (is_soc_rev(CHIP_REV_2_0) == 0) { + /* Set VCC to 1.3V for TO2 */ + val = pmic_reg_read(REG_SW_1); + val = (val & (~0x1F)) | 0x1C; + pmic_reg_write(REG_SW_2, val); + + /* Set VDDA to 1.3V for TO2 */ + val = pmic_reg_read(REG_SW_2); + val = (val & (~0x1F)) | 0x1C; + pmic_reg_write(REG_SW_2, val); + } +} +#endif + +static void setup_iomux_fec(void) +{ + /*FEC_MDIO*/ + mxc_request_iomux(MX53_PIN_FEC_MDIO, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_MDIO, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_22K_PU | PAD_CTL_ODE_OPENDRAIN_ENABLE); + mxc_iomux_set_input(MX53_FEC_FEC_MDI_SELECT_INPUT, 0x1); + + /*FEC_MDC*/ + mxc_request_iomux(MX53_PIN_FEC_MDC, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_MDC, PAD_CTL_DRV_HIGH); + + /* FEC RXD1 */ + mxc_request_iomux(MX53_PIN_FEC_RXD1, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_RXD1, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE); + + /* FEC RXD0 */ + mxc_request_iomux(MX53_PIN_FEC_RXD0, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_RXD0, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE); + + /* FEC TXD1 */ + mxc_request_iomux(MX53_PIN_FEC_TXD1, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_TXD1, PAD_CTL_DRV_HIGH); + + /* FEC TXD0 */ + mxc_request_iomux(MX53_PIN_FEC_TXD0, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_TXD0, PAD_CTL_DRV_HIGH); + + /* FEC TX_EN */ + mxc_request_iomux(MX53_PIN_FEC_TX_EN, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_TX_EN, PAD_CTL_DRV_HIGH); + + /* FEC TX_CLK */ + mxc_request_iomux(MX53_PIN_FEC_REF_CLK, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_REF_CLK, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE); + + /* FEC RX_ER */ + mxc_request_iomux(MX53_PIN_FEC_RX_ER, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_RX_ER, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE); + + /* FEC CRS */ + mxc_request_iomux(MX53_PIN_FEC_CRS_DV, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX53_PIN_FEC_CRS_DV, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE); +} + +#ifdef CONFIG_FSL_ESDHC +struct fsl_esdhc_cfg esdhc_cfg[2] = { + {MMC_SDHC1_BASE_ADDR, 1}, + {MMC_SDHC3_BASE_ADDR, 1}, +}; + +int board_mmc_getcd(u8 *cd, struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + + if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR) + *cd = mxc_gpio_get(77); /*GPIO3_13*/ + else + *cd = mxc_gpio_get(75); /*GPIO3_11*/ + + return 0; +} + +int board_mmc_init(bd_t *bis) +{ + u32 index; + s32 status = 0; + + for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) { + switch (index) { + case 0: + mxc_request_iomux(MX53_PIN_SD1_CMD, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_SD1_CLK, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_SD1_DATA0, + IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_SD1_DATA1, + IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_SD1_DATA2, + IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_SD1_DATA3, + IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_EIM_DA13, + IOMUX_CONFIG_ALT1); + + mxc_iomux_set_pad(MX53_PIN_SD1_CMD, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU); + mxc_iomux_set_pad(MX53_PIN_SD1_CLK, + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU | + PAD_CTL_DRV_HIGH); + mxc_iomux_set_pad(MX53_PIN_SD1_DATA0, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_SD1_DATA1, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_SD1_DATA2, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_SD1_DATA3, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + break; + case 1: + mxc_request_iomux(MX53_PIN_ATA_RESET_B, + IOMUX_CONFIG_ALT2); + mxc_request_iomux(MX53_PIN_ATA_IORDY, + IOMUX_CONFIG_ALT2); + mxc_request_iomux(MX53_PIN_ATA_DATA8, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_ATA_DATA9, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_ATA_DATA10, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_ATA_DATA11, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_ATA_DATA0, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_ATA_DATA1, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_ATA_DATA2, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_ATA_DATA3, + IOMUX_CONFIG_ALT4); + mxc_request_iomux(MX53_PIN_EIM_DA11, + IOMUX_CONFIG_ALT1); + + mxc_iomux_set_pad(MX53_PIN_ATA_RESET_B, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_IORDY, + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU | + PAD_CTL_DRV_HIGH); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA8, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA9, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA10, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA11, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA0, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA1, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA2, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + mxc_iomux_set_pad(MX53_PIN_ATA_DATA3, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH | + PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU); + + break; + default: + printf("Warning: you configured more ESDHC controller" + "(%d) as supported by the board(2)\n", + CONFIG_SYS_FSL_ESDHC_NUM); + return status; + } + status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + } + + return status; +} +#endif + +int board_init(void) +{ + gd->bd->bi_arch_number = MACH_TYPE_MX53_EVK; + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + + setup_iomux_uart(); + setup_iomux_fec(); + + return 0; +} + +#ifdef BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_I2C_MXC + setup_i2c(1); + power_init(); +#endif + return 0; +} +#endif + +int checkboard(void) +{ + u32 cause; + struct src *src_regs = (struct src *)SRC_BASE_ADDR; + + puts("Board: MX53EVK ["); + + cause = src_regs->srsr; + switch (cause) { + case 0x0001: + printf("POR"); + break; + case 0x0009: + printf("RST"); + break; + case 0x0010: + case 0x0011: + printf("WDOG"); + break; + default: + printf("unknown"); + } + printf("]\n"); + return 0; +} diff --git a/boards.cfg b/boards.cfg index dcd5a12..736e88e 100644 --- a/boards.cfg +++ b/boards.cfg @@ -101,6 +101,7 @@ omap5912osk arm arm926ejs - ti edminiv2 arm arm926ejs - LaCie orion5x ca9x4_ct_vxp arm armv7 vexpress armltd mx51evk arm armv7 mx51evk freescale mx5 +mx53evk arm armv7 mx53evk freescale mx5 vision2 arm armv7 vision2 ttcontrol mx5 omap3_overo arm armv7 overo - omap3 omap3_pandora arm armv7 pandora - omap3 diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h new file mode 100755 index 0000000..1c97ef4 --- /dev/null +++ b/include/configs/mx53evk.h @@ -0,0 +1,216 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * Configuration settings for the MX53-EVK Freescale board. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + + /* High Level Configuration Options */ + +#define CONFIG_MX53 + +#define CONFIG_SYS_MX5_HCLK 24000000 +#define CONFIG_SYS_MX5_CLK32 32768 +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_L2_OFF + +#include <asm/arch/imx-regs.h> + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_REVISION_TAG 1 +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) + +#define BOARD_LATE_INIT +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART +#define CONFIG_SYS_MX53_UART1 + +/* + * I2C Configs + */ +#define CONFIG_CMD_I2C 1 +#define CONFIG_HARD_I2C 1 +#define CONFIG_I2C_MXC 1 +#define CONFIG_SYS_I2C_MX53_PORT2 1 +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0xfe + +/* + * PMIC Configs + */ +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_I2C +#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 8 + +/* + * MMC Configs + */ +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define CONFIG_SYS_FSL_ESDHC_NUM 2 + +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION + +/* + * Eth Configs + */ +#define CONFIG_HAS_ETH1 +#define CONFIG_NET_MULTI +#define CONFIG_MII +#define CONFIG_DISCOVER_PHY + +#define CONFIG_FEC_MXC +#define IMX_FEC_BASE FEC_BASE_ADDR +#define CONFIG_FEC_MXC_PHYADDR 0x1F + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} + +/*********************************************************** + * Command definition + ***********************************************************/ + +#include <config_cmd_default.h> + +#undef CONFIG_CMD_IMLS + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_PRIME "FEC0" + +#define CONFIG_LOADADDR 0x70800000 /* loadaddr env var */ +#define CONFIG_SYS_TEXT_BASE 0x77800000 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "mmcdev=0\0" \ + "mmcpart=2\0" \ + "mmcroot=/dev/mmcblk0p3 rw\0" \ + "mmcrootfstype=ext3 rootwait\0" \ + "mmcargs=setenv bootargs console=ttymxc0,${baudrate} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "bootm\0" \ + "netargs=setenv bootargs console=ttymxc0,${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "dhcp ${uimage}; bootm\0" \ + +#define CONFIG_BOOTCOMMAND \ + "if mmc rescan ${mmcdev}; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +#define CONFIG_ARP_TIMEOUT 200UL + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT "MX53EVK U-Boot > " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x70000000 +#define CONFIG_SYS_MEMTEST_END 0x10000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_SYS_HZ 1000 +#define CONFIG_CMDLINE_EDITING + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 CSD0_BASE_ADDR +#define PHYS_SDRAM_1_SIZE (512 * 1024 * 1024) + +#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1) +#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR) +#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE) + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_ENV_SIZE (8 * 1024) +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#endif /* __CONFIG_H */
On 12/22/2010 02:23 PM, Jason Liu wrote:
Add initial support for MX53EVK board support. FEC, SD/MMC, UART, I2C, have been support.
Signed-off-by: Jason Liu r64343@freescale.com
Changes for v2: -Address the comments from Stefano, Albert and Wolfgang, -remove the ivt.S file and use imximage.cfg instead, -remove the ivt link to u-boot -Address the comments from Stefano, -Correct the copyright issue, -Use mxc_get_gpio() and mxc_set_gpio() accessors. -Get rid of system_rev, -use i2c enumeration value (0,1,..N) instead of BASE address, -use fsl_pmic i2c interface, -Add comments for why manage the pmic in a different way for TO2 -Remove the comments from configs/mx53evk.h, - /* - * Disabled for now due to build problems under Debian and a significant - * increase in the final file size: 144260 vs. 109536 Bytes. - */ -Address the comments from Wolfgang, -Move CONFIG_SYS_TEXT_BASE to board config file, -Remove the comments from configs/mx53evk.h - /* size in bytes reserved for initial data */ #define BOARD_LATE_INIT -Change the comments, * Hardware drivers to * UART drivers
MAINTAINERS | 3 + board/freescale/mx53evk/Makefile | 48 +++++ board/freescale/mx53evk/mx53evk.c | 393 +++++++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/mx53evk.h | 216 ++++++++++++++++++++ 5 files changed, 661 insertions(+), 0 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS index 0590ad9..c87ca56 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1085,6 +1085,9 @@ Peter Meerwald devel@bct-electronic.com
bct-brettl2 BF536
+Jason Liu r64343@freescale.com
- MX53evk i.MX53
Why do you add your name at the end of the Blackfin list and not inside the ARM list ? Please maintain the list sorted.
+void power_init(void) +{
- unsigned int val;
- /* Set VDDA to 1.25V */
- val = pmic_reg_read(REG_SW_2);
- val = (val & (~0x1F)) | 0x1A;
I have already commented this. Please drop all fix constants and use already provided #define or add new ones if needed.
- if (is_soc_rev(CHIP_REV_2_0) == 0) {
/* Set VCC to 1.3V for TO2 */val = pmic_reg_read(REG_SW_1);val = (val & (~0x1F)) | 0x1C;
Ditto.
+int board_init(void) +{
- gd->bd->bi_arch_number = MACH_TYPE_MX53_EVK;
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
- setup_iomux_uart();
You sent a patch for mx51evk moving this call in board_early_init_f. Do we need the same for mx53evk ?
+#ifdef BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_I2C_MXC
Is there a possibility to have a working board if CONFIG_I2C_MXC and BOARD_LATE_INIT are not set ? If not, it should be better to check if they are set on the beginning of this file and reporting a compile error if they are not set, and removing the #ifdef in this function.
Best regards, Stefano Babic
Hi, Stefano,
2010/12/27 Stefano Babic sbabic@denx.de:
On 12/22/2010 02:23 PM, Jason Liu wrote:
Add initial support for MX53EVK board support. FEC, SD/MMC, UART, I2C, have been support.
Signed-off-by: Jason Liu r64343@freescale.com
Changes for v2: -Address the comments from Stefano, Albert and Wolfgang, -remove the ivt.S file and use imximage.cfg instead, -remove the ivt link to u-boot -Address the comments from Stefano, -Correct the copyright issue, -Use mxc_get_gpio() and mxc_set_gpio() accessors. -Get rid of system_rev, -use i2c enumeration value (0,1,..N) instead of BASE address, -use fsl_pmic i2c interface, -Add comments for why manage the pmic in a different way for TO2 -Remove the comments from configs/mx53evk.h, - /* - * Disabled for now due to build problems under Debian and a significant - * increase in the final file size: 144260 vs. 109536 Bytes. - */ -Address the comments from Wolfgang, -Move CONFIG_SYS_TEXT_BASE to board config file, -Remove the comments from configs/mx53evk.h - /* size in bytes reserved for initial data */ #define BOARD_LATE_INIT -Change the comments, * Hardware drivers to * UART drivers
MAINTAINERS | 3 + board/freescale/mx53evk/Makefile | 48 +++++ board/freescale/mx53evk/mx53evk.c | 393 +++++++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/mx53evk.h | 216 ++++++++++++++++++++ 5 files changed, 661 insertions(+), 0 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS index 0590ad9..c87ca56 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1085,6 +1085,9 @@ Peter Meerwald devel@bct-electronic.com
bct-brettl2 BF536
+Jason Liu r64343@freescale.com
- MX53evk i.MX53
Why do you add your name at the end of the Blackfin list and not inside the ARM list ? Please maintain the list sorted.
OK, I will put it into the ARM list.
+void power_init(void) +{
- unsigned int val;
- /* Set VDDA to 1.25V */
- val = pmic_reg_read(REG_SW_2);
- val = (val & (~0x1F)) | 0x1A;
I have already commented this. Please drop all fix constants and use already provided #define or add new ones if needed.
Do you think that both 0x1F and 0x1A should be used with #define?
- if (is_soc_rev(CHIP_REV_2_0) == 0) {
- /* Set VCC to 1.3V for TO2 */
- val = pmic_reg_read(REG_SW_1);
- val = (val & (~0x1F)) | 0x1C;
Ditto.
Do you think that both 0x1F and 0x1C should be used with #define?
+int board_init(void) +{
- gd->bd->bi_arch_number = MACH_TYPE_MX53_EVK;
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
- setup_iomux_uart();
You sent a patch for mx51evk moving this call in board_early_init_f. Do we need the same for mx53evk ?
Yes, we need the same for mx53evk.
+#ifdef BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_I2C_MXC
Is there a possibility to have a working board if CONFIG_I2C_MXC and BOARD_LATE_INIT are not set ? If not, it should be better to check if they are set on the beginning of this file and reporting a compile error if they are not set, and removing the #ifdef in this function.
OK, I will remove it.
Thanks for the review.
Best regards, Stefano Babic
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de ===================================================================== _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
On 12/28/2010 08:45 AM, Jason Liu wrote:
/* Set VDDA to 1.25V */val = pmic_reg_read(REG_SW_2);val = (val & (~0x1F)) | 0x1A;I have already commented this. Please drop all fix constants and use already provided #define or add new ones if needed.
Do you think that both 0x1F and 0x1A should be used with #define?
Yes, of course. I see you have not included any specific pmic header in the file (take a look at the mc13892.h file). Nobody knows what 0x1F and 0x1A mean, and everybody relies only on the comment. However, not always a comment is updated...
Do you think that both 0x1F and 0x1C should be used with #define?
Yes
Best regards, Stefano Babic
On 12/22/2010 02:23 PM, Jason Liu wrote:
Add initial support for Freescale MX53 processor,
- Add the iomux support and the pin definition,
- Add the regs definition, clean up some unused def from mx51,
- Add the low level init support, make use the freq input of setup_pll macro
Changes for v2: -address some comments of Stefano Babic, remove the is_soc_type and use #ifdef, -address the comments of stefano, remove CPU_TYPE def, remove something like /*0x760*/ comments in mx5x_pins.h. -fix the build break for vision2 board
A general remark. You posted two different patchset now to support the MX53 processor. As the patches are related, please combine all patches in a single patchset to avoid that only a few of them go to be applied and to simplify review.
Best regards, Stefano Babic
Hi, Stefano,
2010/12/27 Stefano Babic sbabic@denx.de:
On 12/22/2010 02:23 PM, Jason Liu wrote:
Add initial support for Freescale MX53 processor,
- Add the iomux support and the pin definition,
- Add the regs definition, clean up some unused def from mx51,
- Add the low level init support, make use the freq input of setup_pll macro
Changes for v2: -address some comments of Stefano Babic, remove the is_soc_type and use #ifdef, -address the comments of stefano, remove CPU_TYPE def, remove something like /*0x760*/ comments in mx5x_pins.h. -fix the build break for vision2 board
A general remark. You posted two different patchset now to support the MX53 processor. As the patches are related, please combine all patches in a single patchset to avoid that only a few of them go to be applied and to simplify review.
The patch for support mx53 processor is tracked by version. Sorry, I don't catch your mean. Thanks in advance for telling me clear on that if something wrong.
Best regards, Stefano Babic
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de ===================================================================== _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
On 12/28/2010 09:12 AM, Jason Liu wrote:
A general remark. You posted two different patchset now to support the MX53 processor. As the patches are related, please combine all patches in a single patchset to avoid that only a few of them go to be applied and to simplify review.
The patch for support mx53 processor is tracked by version. Sorry, I don't catch your mean. Thanks in advance for telling me clear on that if something wrong.
Patches for mx53evk are in one patchset, but they depends on patches you sent in another patchset (for pmic, gpio,). All patches that belong to the same patchset are merged together into the mainline, avoiding conflicts and board breakages. If for example your first patchset is merged, but the second one is waiting for changes, the board cannot be compiled clean and can potentially break other board, if for example it contains a partial modification that is fixed in the second patchset. Increase the version number and put all related patches in the same patchset.
Best regards, Stefano Babic
Hi, Stefano,
2010/12/28 Stefano Babic sbabic@denx.de:
On 12/28/2010 09:12 AM, Jason Liu wrote:
A general remark. You posted two different patchset now to support the MX53 processor. As the patches are related, please combine all patches in a single patchset to avoid that only a few of them go to be applied and to simplify review.
The patch for support mx53 processor is tracked by version. Sorry, I don't catch your mean. Thanks in advance for telling me clear on that if something wrong.
Patches for mx53evk are in one patchset, but they depends on patches you sent in another patchset (for pmic, gpio,). All patches that belong to the same patchset are merged together into the mainline, avoiding conflicts and board breakages. If for example your first patchset is merged, but the second one is waiting for changes, the board cannot be compiled clean and can potentially break other board, if for example it contains a partial modification that is fixed in the second patchset. Increase the version number and put all related patches in the same patchset.
OK, I get it. Thanks for the clarification.
Best regards, Stefano Babic
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@denx.de =====================================================================
Dear Jason Liu,
In message 1293024212-4858-1-git-send-email-r64343@freescale.com you wrote:
Add initial support for Freescale MX53 processor,
- Add the iomux support and the pin definition,
- Add the regs definition, clean up some unused def from mx51,
- Add the low level init support, make use the freq input of setup_pll macro
...
- ldr r0, =\pll
What does '\p' mean ?
- ldr r1, W_DP_OP_\freq
What does '\f' mean?
Best regards,
Wolfgang Denk
Hi, Wolfgang,
2011/1/10 Wolfgang Denk wd@denx.de:
Dear Jason Liu,
In message 1293024212-4858-1-git-send-email-r64343@freescale.com you wrote:
Add initial support for Freescale MX53 processor,
- Add the iomux support and the pin definition,
- Add the regs definition, clean up some unused def from mx51,
- Add the low level init support, make use the freq input of setup_pll macro
...
- ldr r0, =\pll
What does '\p' mean ?
In order to evaluate the macro parameter, we need put escape sequences before the param.
See, http://sourceware.org/binutils/docs-2.21/as/Macro.html#Macro for detailed information.
- ldr r1, W_DP_OP_\freq
What does '\f' mean?
Ditto,
Best regards,
Wolfgang Denk
-- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de "Don't try to outweird me, three-eyes. I get stranger things than you free with my breakfast cereal." - Zaphod Beeblebrox in "Hitchhiker's Guide to the Galaxy" _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
participants (5)
-
Albert ARIBAUD -
Jason Liu -
Jason Liu -
Stefano Babic -
Wolfgang Denk