New subject: [U-Boot] [PATCH 01/16] i2c, ppc4xx_i2c: switch to new multibus/multiadapter support

25 Apr 2013

diff --git a/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c b/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c
index 48aa753..fd458fd 100644
--- a/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c
+++ b/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c
@@ -52,10 +52,6 @@
 /*
  * Set default values
  */
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED	50000
-#endif
-
 #define ONE_BILLION	1000000000
#define	 SDRAM0_CFG_DCE		0x80000000
@@ -158,7 +154,7 @@ long int spd_sdram(int(read_spd)(uint addr))
    	 * Make sure I2C controller is initialized
    	 * before continuing.
    	 */
-		i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+		i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM);
    }
/* Make shure we are using SDRAM */
diff --git a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c
index 161d274..9c566c1 100644
--- a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c
+++ b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c
@@ -62,10 +62,6 @@
 /*
  * Set default values
  */
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED	50000
-#endif
-
 #define ONE_BILLION	1000000000
/*
@@ -168,7 +164,7 @@ long int spd_sdram(void) {
     * Make sure I2C controller is initialized
     * before continuing.
     */
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM);
/*
     * Read the SPD information using I2C interface. Check to see if the
diff --git a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c
index def7ebf..a66973e 100644
--- a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c
+++ b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c
@@ -459,8 +459,7 @@ phys_size_t initdram(int board_type)
     */
/* switch to correct I2C bus */
-	I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM);
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM);
/*------------------------------------------------------------------
     * Clear out the serial presence detect buffers.
diff --git a/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c b/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c
index 72c5aec..0eafe3e 100644
--- a/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c
+++ b/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c
@@ -56,7 +56,7 @@ static int do_chip_config(cmd_tbl_t *cmdtp, int flag, int argc, char * const arg
     * First switch to correct I2C bus. This is I2C bus 0
     * for all currently available 4xx derivats.
     */
-	I2C_SET_BUS(0);
+	i2c_set_bus_num(0);
#ifdef CONFIG_CMD_EEPROM
    ret = eeprom_read(CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR,
diff --git a/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c b/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c
index 3ceab32..df96375 100644
--- a/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c
+++ b/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c
@@ -1041,8 +1041,7 @@ phys_size_t initdram(int board_type)
     * before continuing.
     */
    /* switch to correct I2C bus */
-	I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM);
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM);
/*------------------------------------------------------------------
     * Clear out the serial presence detect buffers.
diff --git a/arch/powerpc/include/asm/ppc4xx-i2c.h b/arch/powerpc/include/asm/ppc4xx-i2c.h
index 0c6c926..89de508 100644
--- a/arch/powerpc/include/asm/ppc4xx-i2c.h
+++ b/arch/powerpc/include/asm/ppc4xx-i2c.h
@@ -34,24 +34,6 @@
#define IIC_TIMEOUT	1		/* 1 second */
-#if defined(CONFIG_I2C_MULTI_BUS)
-#define I2C_BUS_OFFS	(i2c_bus_num * 0x100)
-#else
-#define I2C_BUS_OFFS	(0x000)
-#endif /* CONFIG_I2C_MULTI_BUS */
-
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
-    defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
-    defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define I2C_BASE_ADDR	(CONFIG_SYS_PERIPHERAL_BASE + 0x00000700 + I2C_BUS_OFFS)
-#elif defined(CONFIG_440) || defined(CONFIG_405EX)
-/* all remaining 440 variants */
-#define I2C_BASE_ADDR	(CONFIG_SYS_PERIPHERAL_BASE + 0x00000400 + I2C_BUS_OFFS)
-#else
-/* all 405 variants */
-#define I2C_BASE_ADDR	(0xEF600500 + I2C_BUS_OFFS)
-#endif
-
 struct ppc4xx_i2c {
    u8 mdbuf;
    u8 res1;
diff --git a/board/csb272/csb272.c b/board/csb272/csb272.c
index 8b36127..a53dac1 100644
--- a/board/csb272/csb272.c
+++ b/board/csb272/csb272.c
@@ -51,7 +51,7 @@ uchar pll_fs6377_regs[16] = {
  */
 int pll_init(void)
 {
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
return  i2c_write(CONFIG_SYS_I2C_PLL_ADDR, 0, 1,
    	(uchar *) pll_fs6377_regs, sizeof(pll_fs6377_regs));
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index 1ada1bc..64d43c5 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -385,7 +385,6 @@ int last_stage_init(void)
    return 0;
 }
-#if defined(CONFIG_I2C_MULTI_BUS)
 /*
  * read field strength from I2C ADC
  */
@@ -500,7 +499,6 @@ U_BOOT_CMD(
    "Initialize USB hub",
    ""
 );
-#endif /* CONFIG_I2C_MULTI_BUS */
#define CONFIG_SYS_BOOT_EEPROM_PAGE_WRITE_BITS 3
 int boot_eeprom_write (unsigned dev_addr,
diff --git a/board/lwmon5/kbd.c b/board/lwmon5/kbd.c
index b66f681..9834bfd 100644
--- a/board/lwmon5/kbd.c
+++ b/board/lwmon5/kbd.c
@@ -111,7 +111,7 @@ static void kbd_init (void)
    uchar val, errcd;
    int i;
-	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
gd->arch.kbd_status = 0;
diff --git a/board/mpl/pip405/pip405.c b/board/mpl/pip405/pip405.c
index b203037..655e129 100644
--- a/board/mpl/pip405/pip405.c
+++ b/board/mpl/pip405/pip405.c
@@ -209,7 +209,7 @@ int board_early_init_f (void)
 #endif
/* Read Serial Presence Detect Information */
-	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
    for (i = 0; i < 128; i++)
    	datain[i] = 127;
    i2c_read(SPD_EEPROM_ADDRESS,0,1,datain,128);
diff --git a/board/sandburst/common/ppc440gx_i2c.c b/board/sandburst/common/ppc440gx_i2c.c
deleted file mode 100644
index 85b63fc..0000000
--- a/board/sandburst/common/ppc440gx_i2c.c
+++ /dev/null
@@ -1,510 +0,0 @@
-/*
- *  Copyright (C) 2005 Sandburst Corporation
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * Ported from arch/powerpc/cpu/ppc4xx/i2c.c by AS HARNOIS by
- * Travis B. Sawyer
- * Sandburst Corporation.
- */
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/ppc4xx-i2c.h>
-#include <i2c.h>
-#include <command.h>
-#include "ppc440gx_i2c.h"
-#include <asm/io.h>
-
-#ifdef CONFIG_I2C_BUS1
-
-#define IIC_OK		0
-#define IIC_NOK		1
-#define IIC_NOK_LA	2		/* Lost arbitration */
-#define IIC_NOK_ICT	3		/* Incomplete transfer */
-#define IIC_NOK_XFRA	4		/* Transfer aborted */
-#define IIC_NOK_DATA	5		/* No data in buffer */
-#define IIC_NOK_TOUT	6		/* Transfer timeout */
-
-#define IIC_TIMEOUT 1			/* 1 second */
-#if defined(CONFIG_SYS_I2C_NOPROBES)
-static uchar i2c_no_probes[] = CONFIG_SYS_I2C_NOPROBES;
-#endif
-
-static struct ppc4xx_i2c *i2c = (struct ppc4xx_i2c *)I2C_REGISTERS_BUS1_BASE_ADDRESS;
-
-static void _i2c_bus1_reset (void)
-{
-	int i, status;
-
-	/* Reset status register */
-	/* write 1 in SCMP and IRQA to clear these fields */
-	out_8 (IIC_STS1, 0x0A);
-
-	/* write 1 in IRQP IRQD LA ICT XFRA to clear these fields */
-	out_8 (IIC_EXTSTS1, 0x8F);
-	__asm__ volatile ("eieio");
-
-	/*
-	 * Get current state, reset bus
-	 * only if no transfers are pending.
-	 */
-	i = 10;
-	do {
-		/* Get status */
-		status = in_8 (IIC_STS1);
-		udelay (500);			/* 500us */
-		i--;
-	} while ((status & IIC_STS_PT) && (i > 0));
-	/* Soft reset controller */
-	status = in_8 (IIC_XTCNTLSS1);
-	out_8 (IIC_XTCNTLSS1, (status | IIC_XTCNTLSS_SRST));
-	__asm__ volatile ("eieio");
-
-	/* make sure where in initial state, data hi, clock hi */
-	out_8 (IIC_DIRECTCNTL1, 0xC);
-	for (i = 0; i < 10; i++) {
-		if ((in_8 (IIC_DIRECTCNTL1) & 0x3) != 0x3) {
-			/* clock until we get to known state */
-			out_8 (IIC_DIRECTCNTL1, 0x8);	/* clock lo */
-			udelay (100);		/* 100us */
-			out_8 (IIC_DIRECTCNTL1, 0xC);	/* clock hi */
-			udelay (100);		/* 100us */
-		} else {
-			break;
-		}
-	}
-	/* send start condition */
-	out_8 (IIC_DIRECTCNTL1, 0x4);
-	udelay (1000);				/* 1ms */
-	/* send stop condition */
-	out_8 (IIC_DIRECTCNTL1, 0xC);
-	udelay (1000);				/* 1ms */
-	/* Unreset controller */
-	out_8 (IIC_XTCNTLSS1, (status & ~IIC_XTCNTLSS_SRST));
-	udelay (1000);				/* 1ms */
-}
-
-void i2c1_init (int speed, int slaveadd)
-{
-	sys_info_t sysInfo;
-	unsigned long freqOPB;
-	int val, divisor;
-
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
-	/* call board specific i2c bus reset routine before accessing the   */
-	/* environment, which might be in a chip on that bus. For details   */
-	/* about this problem see doc/I2C_Edge_Conditions.                  */
-	i2c_init_board();
-#endif
-
-	/* Handle possible failed I2C state */
-	/* FIXME: put this into i2c_init_board()? */
-	_i2c_bus1_reset ();
-
-	/* clear lo master address */
-	out_8 (IIC_LMADR1, 0);
-
-	/* clear hi master address */
-	out_8 (IIC_HMADR1, 0);
-
-	/* clear lo slave address */
-	out_8 (IIC_LSADR1, 0);
-
-	/* clear hi slave address */
-	out_8 (IIC_HSADR1, 0);
-
-	/* Clock divide Register */
-	/* get OPB frequency */
-	get_sys_info (&sysInfo);
-	freqOPB = sysInfo.freqPLB / sysInfo.pllOpbDiv;
-	/* set divisor according to freqOPB */
-	divisor = (freqOPB - 1) / 10000000;
-	if (divisor == 0)
-		divisor = 1;
-	out_8 (IIC_CLKDIV1, divisor);
-
-	/* no interrupts */
-	out_8 (IIC_INTRMSK1, 0);
-
-	/* clear transfer count */
-	out_8 (IIC_XFRCNT1, 0);
-
-	/* clear extended control & stat */
-	/* write 1 in SRC SRS SWC SWS to clear these fields */
-	out_8 (IIC_XTCNTLSS1, 0xF0);
-
-	/* Mode Control Register
-	   Flush Slave/Master data buffer */
-	out_8 (IIC_MDCNTL1, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB);
-	__asm__ volatile ("eieio");
-
-
-	val = in_8(IIC_MDCNTL1);
-	__asm__ volatile ("eieio");
-
-	/* Ignore General Call, slave transfers are ignored,
-	   disable interrupts, exit unknown bus state, enable hold
-	   SCL
-	   100kHz normaly or FastMode for 400kHz and above
-	*/
-
-	val |= IIC_MDCNTL_EUBS|IIC_MDCNTL_HSCL;
-	if( speed >= 400000 ){
-		val |= IIC_MDCNTL_FSM;
-	}
-	out_8 (IIC_MDCNTL1, val);
-
-	/* clear control reg */
-	out_8 (IIC_CNTL1, 0x00);
-	__asm__ volatile ("eieio");
-
-}
-
-/*
-  This code tries to use the features of the 405GP i2c
-  controller. It will transfer up to 4 bytes in one pass
-  on the loop. It only does out_8(lbz) to the buffer when it
-  is possible to do out16(lhz) transfers.
-
-  cmd_type is 0 for write 1 for read.
-
-  addr_len can take any value from 0-255, it is only limited
-  by the char, we could make it larger if needed. If it is
-  0 we skip the address write cycle.
-
-  Typical case is a Write of an addr followd by a Read. The
-  IBM FAQ does not cover this. On the last byte of the write
-  we don't set the creg CHT bit, and on the first bytes of the
-  read we set the RPST bit.
-
-  It does not support address only transfers, there must be
-  a data part. If you want to write the address yourself, put
-  it in the data pointer.
-
-  It does not support transfer to/from address 0.
-
-  It does not check XFRCNT.
-*/
-static
-int i2c_transfer1(unsigned char cmd_type,
-		  unsigned char chip,
-		  unsigned char addr[],
-		  unsigned char addr_len,
-		  unsigned char data[],
-		  unsigned short data_len )
-{
-	unsigned char* ptr;
-	int reading;
-	int tran,cnt;
-	int result;
-	int status;
-	int i;
-	uchar creg;
-
-	if( data == 0 || data_len == 0 ){
-		/*Don't support data transfer of no length or to address 0*/
-		printf( "i2c_transfer: bad call\n" );
-		return IIC_NOK;
-	}
-	if( addr && addr_len ){
-		ptr = addr;
-		cnt = addr_len;
-		reading = 0;
-	}else{
-		ptr = data;
-		cnt = data_len;
-		reading = cmd_type;
-	}
-
-	/*Clear Stop Complete Bit*/
-	out_8(IIC_STS1,IIC_STS_SCMP);
-	/* Check init */
-	i=10;
-	do {
-		/* Get status */
-		status = in_8(IIC_STS1);
-		__asm__ volatile("eieio");
-		i--;
-	} while ((status & IIC_STS_PT) && (i>0));
-
-	if (status & IIC_STS_PT) {
-		result = IIC_NOK_TOUT;
-		return(result);
-	}
-	/*flush the Master/Slave Databuffers*/
-	out_8(IIC_MDCNTL1, ((in_8(IIC_MDCNTL1))|IIC_MDCNTL_FMDB|IIC_MDCNTL_FSDB));
-	/*need to wait 4 OPB clocks? code below should take that long*/
-
-	/* 7-bit adressing */
-	out_8(IIC_HMADR1,0);
-	out_8(IIC_LMADR1, chip);
-	__asm__ volatile("eieio");
-
-	tran = 0;
-	result = IIC_OK;
-	creg = 0;
-
-	while ( tran != cnt && (result == IIC_OK)) {
-		int  bc,j;
-
-		/* Control register =
-		   Normal transfer, 7-bits adressing, Transfer up to bc bytes, Normal start,
-		   Transfer is a sequence of transfers
-		*/
-		creg |= IIC_CNTL_PT;
-
-		bc = (cnt - tran) > 4 ? 4 :
-			cnt - tran;
-		creg |= (bc-1)<<4;
-		/* if the real cmd type is write continue trans*/
-		if ( (!cmd_type && (ptr == addr)) || ((tran+bc) != cnt) )
-			creg |= IIC_CNTL_CHT;
-
-		if (reading)
-			creg |= IIC_CNTL_READ;
-		else {
-			for(j=0; j<bc; j++) {
-				/* Set buffer */
-				out_8(IIC_MDBUF1,ptr[tran+j]);
-				__asm__ volatile("eieio");
-			}
-		}
-		out_8(IIC_CNTL1, creg );
-		__asm__ volatile("eieio");
-
-		/* Transfer is in progress
-		   we have to wait for upto 5 bytes of data
-		   1 byte chip address+r/w bit then bc bytes
-		   of data.
-		   udelay(10) is 1 bit time at 100khz
-		   Doubled for slop. 20 is too small.
-		*/
-		i=2*5*8;
-		do {
-			/* Get status */
-			status = in_8(IIC_STS1);
-			__asm__ volatile("eieio");
-			udelay (10);
-			i--;
-		} while ((status & IIC_STS_PT) && !(status & IIC_STS_ERR)
-			 && (i>0));
-
-		if (status & IIC_STS_ERR) {
-			result = IIC_NOK;
-			status = in_8 (IIC_EXTSTS1);
-			/* Lost arbitration? */
-			if (status & IIC_EXTSTS_LA)
-				result = IIC_NOK_LA;
-			/* Incomplete transfer? */
-			if (status & IIC_EXTSTS_ICT)
-				result = IIC_NOK_ICT;
-			/* Transfer aborted? */
-			if (status & IIC_EXTSTS_XFRA)
-				result = IIC_NOK_XFRA;
-		} else if ( status & IIC_STS_PT) {
-			result = IIC_NOK_TOUT;
-		}
-		/* Command is reading => get buffer */
-		if ((reading) && (result == IIC_OK)) {
-			/* Are there data in buffer */
-			if (status & IIC_STS_MDBS) {
-				/*
-				  even if we have data we have to wait 4OPB clocks
-				  for it to hit the front of the FIFO, after that
-				  we can just read. We should check XFCNT here and
-				  if the FIFO is full there is no need to wait.
-				*/
-				udelay (1);
-				for(j=0;j<bc;j++) {
-					ptr[tran+j] = in_8(IIC_MDBUF1);
-					__asm__ volatile("eieio");
-				}
-			} else
-				result = IIC_NOK_DATA;
-		}
-		creg = 0;
-		tran+=bc;
-		if( ptr == addr && tran == cnt ) {
-			ptr = data;
-			cnt = data_len;
-			tran = 0;
-			reading = cmd_type;
-			if( reading )
-				creg = IIC_CNTL_RPST;
-		}
-	}
-	return (result);
-}
-
-int i2c_probe1 (uchar chip)
-{
-	uchar buf[1];
-
-	buf[0] = 0;
-
-	/*
-	 * What is needed is to send the chip address and verify that the
-	 * address was <ACK>ed (i.e. there was a chip at that address which
-	 * drove the data line low).
-	 */
-	return(i2c_transfer1 (1, chip << 1, 0,0, buf, 1) != 0);
-}
-
-
-int i2c_read1 (uchar chip, uint addr, int alen, uchar * buffer, int len)
-{
-	uchar xaddr[4];
-	int ret;
-
-	if ( alen > 4 ) {
-		printf ("I2C read: addr len %d not supported\n", alen);
-		return 1;
-	}
-
-	if ( alen > 0 ) {
-		xaddr[0] = (addr >> 24) & 0xFF;
-		xaddr[1] = (addr >> 16) & 0xFF;
-		xaddr[2] = (addr >> 8) & 0xFF;
-		xaddr[3] = addr & 0xFF;
-	}
-
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
-	/*
-	 * EEPROM chips that implement "address overflow" are ones
-	 * like Catalyst 24WC04/08/16 which has 9/10/11 bits of
-	 * address and the extra bits end up in the "chip address"
-	 * bit slots. This makes a 24WC08 (1Kbyte) chip look like
-	 * four 256 byte chips.
-	 *
-	 * Note that we consider the length of the address field to
-	 * still be one byte because the extra address bits are
-	 * hidden in the chip address.
-	 */
-	if( alen > 0 )
-		chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-	if( (ret = i2c_transfer1( 1, chip<<1, &xaddr[4-alen], alen, buffer, len )) != 0) {
-		printf( "I2c read: failed %d\n", ret);
-		return 1;
-	}
-	return 0;
-}
-
-int i2c_write1 (uchar chip, uint addr, int alen, uchar * buffer, int len)
-{
-	uchar xaddr[4];
-
-	if ( alen > 4 ) {
-		printf ("I2C write: addr len %d not supported\n", alen);
-		return 1;
-
-	}
-	if ( alen > 0 ) {
-		xaddr[0] = (addr >> 24) & 0xFF;
-		xaddr[1] = (addr >> 16) & 0xFF;
-		xaddr[2] = (addr >> 8) & 0xFF;
-		xaddr[3] = addr & 0xFF;
-	}
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
-	/*
-	 * EEPROM chips that implement "address overflow" are ones
-	 * like Catalyst 24WC04/08/16 which has 9/10/11 bits of
-	 * address and the extra bits end up in the "chip address"
-	 * bit slots. This makes a 24WC08 (1Kbyte) chip look like
-	 * four 256 byte chips.
-	 *
-	 * Note that we consider the length of the address field to
-	 * still be one byte because the extra address bits are
-	 * hidden in the chip address.
-	 */
-	if( alen > 0 )
-		chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
-	return (i2c_transfer1( 0, chip<<1, &xaddr[4-alen], alen, buffer, len ) != 0);
-}
-
-/*-----------------------------------------------------------------------
- * Read a register
- */
-uchar i2c_reg_read1(uchar i2c_addr, uchar reg)
-{
-	uchar buf;
-
-	i2c_read1(i2c_addr, reg, 1, &buf, (uchar)1);
-
-	return(buf);
-}
-
-/*-----------------------------------------------------------------------
- * Write a register
- */
-void i2c_reg_write1(uchar i2c_addr, uchar reg, uchar val)
-{
-	i2c_write1(i2c_addr, reg, 1, &val, 1);
-}
-
-
-int do_i2c1_probe(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	int j;
-#if defined(CONFIG_SYS_I2C_NOPROBES)
-	int k, skip;
-#endif
-
-	puts ("Valid chip addresses:");
-	for(j = 0; j < 128; j++) {
-#if defined(CONFIG_SYS_I2C_NOPROBES)
-		skip = 0;
-		for (k = 0; k < sizeof(i2c_no_probes); k++){
-			if (j == i2c_no_probes[k]){
-				skip = 1;
-				break;
-			}
-		}
-		if (skip)
-			continue;
-#endif
-		if(i2c_probe1(j) == 0) {
-			printf(" %02X", j);
-		}
-	}
-	putc ('\n');
-
-#if defined(CONFIG_SYS_I2C_NOPROBES)
-	puts ("Excluded chip addresses:");
-	for( k = 0; k < sizeof(i2c_no_probes); k++ )
-		printf(" %02X", i2c_no_probes[k] );
-	putc ('\n');
-#endif
-
-	return 0;
-}
-
-U_BOOT_CMD(
-	iprobe1,	1,	1,	do_i2c1_probe,
-	"probe to discover valid I2C chip addresses",
-	""
-);
-
-#endif	/* CONFIG_I2C_BUS1 */
diff --git a/board/sandburst/common/ppc440gx_i2c.h b/board/sandburst/common/ppc440gx_i2c.h
deleted file mode 100644
index 7496db4..0000000
--- a/board/sandburst/common/ppc440gx_i2c.h
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- *  Copyright (C) 2005 Sandburst Corporation
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * Ported from i2c driver for ppc4xx by AS HARNOIS by
- * Travis B. Sawyer
- * Sandburst Corporation
- */
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/ppc4xx-i2c.h>
-#include <i2c.h>
-
-#ifdef CONFIG_HARD_I2C
-
-#define I2C_BUS1_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x00000500)
-#define	   I2C_REGISTERS_BUS1_BASE_ADDRESS I2C_BUS1_BASE_ADDR
-#define    IIC_MDBUF1	(&i2c->mdbuf)
-#define    IIC_SDBUF1	(&i2c->sdbuf)
-#define    IIC_LMADR1	(&i2c->lmadr)
-#define    IIC_HMADR1	(&i2c->hmadr)
-#define    IIC_CNTL1	(&i2c->cntl)
-#define    IIC_MDCNTL1	(&i2c->mdcntl)
-#define    IIC_STS1	(&i2c->sts)
-#define    IIC_EXTSTS1	(&i2c->extsts)
-#define    IIC_LSADR1	(&i2c->lsadr)
-#define    IIC_HSADR1	(&i2c->hsadr)
-#define    IIC_CLKDIV1	(&i2c->clkdiv)
-#define    IIC_INTRMSK1	(&i2c->intrmsk)
-#define    IIC_XFRCNT1	(&i2c->xfrcnt)
-#define    IIC_XTCNTLSS1	(&i2c->xtcntlss)
-#define    IIC_DIRECTCNTL1 (&i2c->directcntl)
-
-void i2c1_init (int speed, int slaveadd);
-int i2c_probe1 (uchar chip);
-int i2c_read1 (uchar chip, uint addr, int alen, uchar * buffer, int len);
-int i2c_write1 (uchar chip, uint addr, int alen, uchar * buffer, int len);
-uchar i2c_reg_read1(uchar i2c_addr, uchar reg);
-void i2c_reg_write1(uchar i2c_addr, uchar reg, uchar val);
-
-#endif	/* CONFIG_HARD_I2C */
diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index 6b91074..305e110 100644
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -26,7 +26,6 @@
 #include <asm/io.h>
 #include <spd_sdram.h>
 #include <i2c.h>
-#include "ppc440gx_i2c.h"
 #include "sb_common.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -84,7 +83,7 @@ unsigned short sbcommon_get_serial_number(void)
/* Get the board serial number from eeprom */
    /* Initialize I2C */
-	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
/* Read 256 bytes in EEPROM */
    i2c_read (0x50, 0, 1, buff, 0x100);
@@ -110,85 +109,87 @@ void sbcommon_fans(void)
     * Attempt to turn on 2 of the fans...
     * Need to go through the bridge
     */
+	i2c_set_bus_num(1);
    puts ("FANS:  ");
/* select fan4 through the bridge */
-	i2c_reg_write1(0x73, /* addr */
-		       0x00, /* reg */
-		       0x08); /* val = bus 4 */
+	i2c_reg_write(0x73, /* addr */
+		      0x00, /* reg */
+		      0x08); /* val = bus 4 */
/* Turn on FAN 4 */
-	i2c_reg_write1(0x2e,
-		       1,
-		       0x80);
+	i2c_reg_write(0x2e,
+		      1,
+		      0x80);
-	i2c_reg_write1(0x2e,
-		       0,
-		       0x19);
+	i2c_reg_write(0x2e,
+		      0,
+		      0x19);
/* Deselect bus 4 on the bridge */
-	i2c_reg_write1(0x73,
-		       0x00,
-		       0x00);
+	i2c_reg_write(0x73,
+		      0x00,
+		      0x00);
/* select fan3 through the bridge */
-	i2c_reg_write1(0x73, /* addr */
-		       0x00, /* reg */
-		       0x04); /* val = bus 3 */
+	i2c_reg_write(0x73, /* addr */
+		      0x00, /* reg */
+		      0x04); /* val = bus 3 */
/* Turn on FAN 3 */
-	i2c_reg_write1(0x2e,
-		       1,
-		       0x80);
+	i2c_reg_write(0x2e,
+		      1,
+		      0x80);
-	i2c_reg_write1(0x2e,
-		       0,
-		       0x19);
+	i2c_reg_write(0x2e,
+		      0,
+		      0x19);
/* Deselect bus 3 on the bridge */
-	i2c_reg_write1(0x73,
-		       0x00,
-		       0x00);
+	i2c_reg_write(0x73,
+		      0x00,
+		      0x00);
/* select fan2 through the bridge */
-	i2c_reg_write1(0x73, /* addr */
-		       0x00, /* reg */
-		       0x02); /* val = bus 4 */
+	i2c_reg_write(0x73, /* addr */
+		      0x00, /* reg */
+		      0x02); /* val = bus 4 */
/* Turn on FAN 2 */
-	i2c_reg_write1(0x2e,
-		       1,
-		       0x80);
+	i2c_reg_write(0x2e,
+		      1,
+		      0x80);
-	i2c_reg_write1(0x2e,
-		       0,
-		       0x19);
+	i2c_reg_write(0x2e,
+		      0,
+		      0x19);
/* Deselect bus 2 on the bridge */
-	i2c_reg_write1(0x73,
-		       0x00,
-		       0x00);
+	i2c_reg_write(0x73,
+		      0x00,
+		      0x00);
/* select fan1 through the bridge */
-	i2c_reg_write1(0x73, /* addr */
-		       0x00, /* reg */
-		       0x01); /* val = bus 0 */
+	i2c_reg_write(0x73, /* addr */
+		      0x00, /* reg */
+		      0x01); /* val = bus 0 */
/* Turn on FAN 1 */
-	i2c_reg_write1(0x2e,
-		       1,
-		       0x80);
+	i2c_reg_write(0x2e,
+		      1,
+		      0x80);
-	i2c_reg_write1(0x2e,
-		       0,
-		       0x19);
+	i2c_reg_write(0x2e,
+		      0,
+		      0x19);
/* Deselect bus 1 on the bridge */
-	i2c_reg_write1(0x73,
-		       0x00,
-		       0x00);
+	i2c_reg_write(0x73,
+		      0x00,
+		      0x00);
puts ("on\n");
+	i2c_set_bus_num(0);
return;
@@ -319,7 +320,7 @@ void board_get_enetaddr(int macaddr_idx, uchar *enet)
    if (0 == macaddr_idx) {
/* Initialize I2C */
-		i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+		i2c_set_bus_num(0);
/* Read 256 bytes in EEPROM */
    	i2c_read (0x50, 0, 1, buff, 0x100);
diff --git a/board/sandburst/common/sb_common.h b/board/sandburst/common/sb_common.h
index e652ba8..5b28244 100644
--- a/board/sandburst/common/sb_common.h
+++ b/board/sandburst/common/sb_common.h
@@ -28,7 +28,6 @@
 #include <asm/io.h>
 #include <spd_sdram.h>
 #include <i2c.h>
-#include "ppc440gx_i2c.h"
/*
  * GPIO Settings
diff --git a/board/sandburst/karef/Makefile b/board/sandburst/karef/Makefile
index fe9b514..d9b3170 100644
--- a/board/sandburst/karef/Makefile
+++ b/board/sandburst/karef/Makefile
@@ -40,8 +40,7 @@ CFLAGS += -DBUILDUSER='"$(BUILDUSER)"'
LIB	= $(obj)lib$(BOARD).o
-COBJS	= $(BOARD).o ../common/flash.o ../common/ppc440gx_i2c.o \
-	../common/sb_common.o
+COBJS	= $(BOARD).o ../common/flash.o ../common/sb_common.o
SOBJS	= init.o
diff --git a/board/sandburst/karef/karef.c b/board/sandburst/karef/karef.c
index 186998d..d156844 100644
--- a/board/sandburst/karef/karef.c
+++ b/board/sandburst/karef/karef.c
@@ -337,11 +337,6 @@ int checkboard (void)
  ************************************************************************/
 int misc_init_f (void)
 {
-	/* Turn on i2c bus 1 */
-	puts ("I2C1:  ");
-	i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-	puts ("ready\n");
-
    /* Turn on fans 3 & 4 */
    sbcommon_fans();
diff --git a/board/sandburst/metrobox/Makefile b/board/sandburst/metrobox/Makefile
index 6019d59..3f19bf2 100644
--- a/board/sandburst/metrobox/Makefile
+++ b/board/sandburst/metrobox/Makefile
@@ -39,8 +39,7 @@ CFLAGS += -DBUILDUSER='"$(BUILDUSER)"'
LIB	= $(obj)lib$(BOARD).o
-COBJS	= $(BOARD).o ../common/flash.o ../common/ppc440gx_i2c.o \
-	../common/sb_common.o
+COBJS	= $(BOARD).o ../common/flash.o ../common/sb_common.o
 SOBJS	= init.o
SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c
index 76d8293..ce4a029 100644
--- a/board/sandburst/metrobox/metrobox.c
+++ b/board/sandburst/metrobox/metrobox.c
@@ -30,7 +30,6 @@
 #include <asm/io.h>
 #include <spd_sdram.h>
 #include <i2c.h>
-#include "../common/ppc440gx_i2c.h"
 #include "../common/sb_common.h"
 #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \
     defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3)
@@ -305,11 +304,6 @@ int checkboard (void)
  ************************************************************************/
 int misc_init_f (void)
 {
-	/* Turn on i2c bus 1 */
-	puts ("I2C1:  ");
-	i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-	puts ("ready\n");
-
    /* Turn on fans */
    sbcommon_fans();
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 564d061..0298e3e 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -36,7 +36,6 @@ COBJS-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o
 COBJS-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o
 COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o
 COBJS-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
-COBJS-$(CONFIG_PPC4XX_I2C) += ppc4xx_i2c.o
 COBJS-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
 COBJS-$(CONFIG_S3C44B0_I2C) += s3c44b0_i2c.o
 COBJS-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
@@ -45,6 +44,7 @@ COBJS-$(CONFIG_SH_I2C) += sh_i2c.o
 COBJS-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
 COBJS-$(CONFIG_SYS_I2C) += i2c_core.o
 COBJS-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o
+COBJS-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o
 COBJS-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
 COBJS-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o
diff --git a/drivers/i2c/ppc4xx_i2c.c b/drivers/i2c/ppc4xx_i2c.c
index 53fedd5..c924874 100644
--- a/drivers/i2c/ppc4xx_i2c.c
+++ b/drivers/i2c/ppc4xx_i2c.c
@@ -32,27 +32,29 @@
 #include <i2c.h>
 #include <asm/io.h>
-#ifdef CONFIG_HARD_I2C
-
 DECLARE_GLOBAL_DATA_PTR;
-#if defined(CONFIG_I2C_MULTI_BUS)
-/*
- * Initialize the bus pointer to whatever one the SPD EEPROM is on.
- * Default is bus 0.  This is necessary because the DDR initialization
- * runs from ROM, and we can't switch buses because we can't modify
- * the global variables.
- */
-#ifndef CONFIG_SYS_SPD_BUS_NUM
-#define CONFIG_SYS_SPD_BUS_NUM	0
+static inline struct ppc4xx_i2c *ppc4xx_get_i2c(int hwadapnr)
+{
+	unsigned long base;
+
+#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+	defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+	defined(CONFIG_460EX) || defined(CONFIG_460GT)
+	base = CONFIG_SYS_PERIPHERAL_BASE + 0x00000700 + (hwadapnr * 0x100);
+#elif defined(CONFIG_440) || defined(CONFIG_405EX)
+/* all remaining 440 variants */
+	base = CONFIG_SYS_PERIPHERAL_BASE + 0x00000400 + (hwadapnr * 0x100);
+#else
+/* all 405 variants */
+	base = 0xEF600500 + (hwadapnr * 0x100);
 #endif
-static unsigned int i2c_bus_num __attribute__ ((section (".data"))) =
-	CONFIG_SYS_SPD_BUS_NUM;
-#endif /* CONFIG_I2C_MULTI_BUS */
+	return (struct ppc4xx_i2c *)base;
+}
-static void _i2c_bus_reset(void)
+static void _i2c_bus_reset(struct i2c_adapter *adap)
 {
-	struct ppc4xx_i2c *i2c = (struct ppc4xx_i2c *)I2C_BASE_ADDR;
+	struct ppc4xx_i2c *i2c = ppc4xx_get_i2c(adap->hwadapnr);
    int i;
    u8 dc;
@@ -91,11 +93,10 @@ static void _i2c_bus_reset(void)
    out_8(&i2c->xtcntlss, 0);
 }
-void i2c_init(int speed, int slaveaddr)
+static void ppc4xx_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
 {
-	struct ppc4xx_i2c *i2c;
+	struct ppc4xx_i2c *i2c = ppc4xx_get_i2c(adap->hwadapnr);
    int val, divisor;
-	int bus;
#ifdef CONFIG_SYS_I2C_INIT_BOARD
    /*
@@ -106,67 +107,57 @@ void i2c_init(int speed, int slaveaddr)
    i2c_init_board();
 #endif
-	for (bus = 0; bus < CONFIG_SYS_MAX_I2C_BUS; bus++) {
-		I2C_SET_BUS(bus);
-
-		/* Set i2c pointer after calling I2C_SET_BUS() */
-		i2c = (struct ppc4xx_i2c *)I2C_BASE_ADDR;
-
-		/* Handle possible failed I2C state */
-		/* FIXME: put this into i2c_init_board()? */
-		_i2c_bus_reset();
+	/* Handle possible failed I2C state */
+	/* FIXME: put this into i2c_init_board()? */
+	_i2c_bus_reset(adap);
-		/* clear lo master address */
-		out_8(&i2c->lmadr, 0);
+	/* clear lo master address */
+	out_8(&i2c->lmadr, 0);
-		/* clear hi master address */
-		out_8(&i2c->hmadr, 0);
-
-		/* clear lo slave address */
-		out_8(&i2c->lsadr, 0);
+	/* clear hi master address */
+	out_8(&i2c->hmadr, 0);
-		/* clear hi slave address */
-		out_8(&i2c->hsadr, 0);
+	/* clear lo slave address */
+	out_8(&i2c->lsadr, 0);
-		/* Clock divide Register */
-		/* set divisor according to freq_opb */
-		divisor = (get_OPB_freq() - 1) / 10000000;
-		if (divisor == 0)
-			divisor = 1;
-		out_8(&i2c->clkdiv, divisor);
+	/* clear hi slave address */
+	out_8(&i2c->hsadr, 0);
-		/* no interrupts */
-		out_8(&i2c->intrmsk, 0);
+	/* Clock divide Register */
+	/* set divisor according to freq_opb */
+	divisor = (get_OPB_freq() - 1) / 10000000;
+	if (divisor == 0)
+		divisor = 1;
+	out_8(&i2c->clkdiv, divisor);
-		/* clear transfer count */
-		out_8(&i2c->xfrcnt, 0);
+	/* no interrupts */
+	out_8(&i2c->intrmsk, 0);
-		/* clear extended control & stat */
-		/* write 1 in SRC SRS SWC SWS to clear these fields */
-		out_8(&i2c->xtcntlss, 0xF0);
+	/* clear transfer count */
+	out_8(&i2c->xfrcnt, 0);
-		/* Mode Control Register
-		   Flush Slave/Master data buffer */
-		out_8(&i2c->mdcntl, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB);
+	/* clear extended control & stat */
+	/* write 1 in SRC SRS SWC SWS to clear these fields */
+	out_8(&i2c->xtcntlss, 0xF0);
-		val = in_8(&i2c->mdcntl);
+	/* Mode Control Register
+	   Flush Slave/Master data buffer */
+	out_8(&i2c->mdcntl, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB);
-		/* Ignore General Call, slave transfers are ignored,
-		 * disable interrupts, exit unknown bus state, enable hold
-		 * SCL 100kHz normaly or FastMode for 400kHz and above
-		 */
+	val = in_8(&i2c->mdcntl);
-		val |= IIC_MDCNTL_EUBS | IIC_MDCNTL_HSCL;
-		if (speed >= 400000)
-			val |= IIC_MDCNTL_FSM;
-		out_8(&i2c->mdcntl, val);
+	/* Ignore General Call, slave transfers are ignored,
+	 * disable interrupts, exit unknown bus state, enable hold
+	 * SCL 100kHz normaly or FastMode for 400kHz and above
+	 */
-		/* clear control reg */
-		out_8(&i2c->cntl, 0x00);
-	}
+	val |= IIC_MDCNTL_EUBS | IIC_MDCNTL_HSCL;
+	if (speed >= 400000)
+		val |= IIC_MDCNTL_FSM;
+	out_8(&i2c->mdcntl, val);
-	/* set to SPD bus as default bus upon powerup */
-	I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM);
+	/* clear control reg */
+	out_8(&i2c->cntl, 0x00);
 }
/*
@@ -194,14 +185,15 @@ void i2c_init(int speed, int slaveaddr)
  *
  * It does not check XFRCNT.
  */
-static int i2c_transfer(unsigned char cmd_type,
+static int _i2c_transfer(struct i2c_adapter *adap,
+			unsigned char cmd_type,
    		unsigned char chip,
    		unsigned char addr[],
    		unsigned char addr_len,
    		unsigned char data[],
    		unsigned short data_len)
 {
-	struct ppc4xx_i2c *i2c = (struct ppc4xx_i2c *)I2C_BASE_ADDR;
+	struct ppc4xx_i2c *i2c = ppc4xx_get_i2c(adap->hwadapnr);
    u8 *ptr;
    int reading;
    int tran, cnt;
@@ -345,7 +337,7 @@ static int i2c_transfer(unsigned char cmd_type,
    return result;
 }
-int i2c_probe(uchar chip)
+static int ppc4xx_i2c_probe(struct i2c_adapter *adap, uchar chip)
 {
    uchar buf[1];
@@ -356,11 +348,11 @@ int i2c_probe(uchar chip)
     * address was <ACK>ed (i.e. there was a chip at that address which
     * drove the data line low).
     */
-	return (i2c_transfer(1, chip << 1, 0, 0, buf, 1) != 0);
+	return (_i2c_transfer(adap, 1, chip << 1, 0, 0, buf, 1) != 0);
 }
-static int ppc4xx_i2c_transfer(uchar chip, uint addr, int alen, uchar *buffer,
-			       int len, int read)
+static int ppc4xx_i2c_transfer(struct i2c_adapter *adap, uchar chip, uint addr,
+			       int alen, uchar *buffer, int len, int read)
 {
    uchar xaddr[4];
    int ret;
@@ -394,43 +386,50 @@ static int ppc4xx_i2c_transfer(uchar chip, uint addr, int alen, uchar *buffer,
    	chip |= ((addr >> (alen * 8)) &
    		 CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
 #endif
-	if ((ret = i2c_transfer(read, chip << 1, &xaddr[4 - alen], alen,
-				buffer, len)) != 0) {
+	ret = _i2c_transfer(adap, read, chip << 1, &xaddr[4 - alen], alen,
+			    buffer, len);
+	if (ret) {
    	printf("I2C %s: failed %d\n", read ? "read" : "write", ret);
-
    	return 1;
    }
return 0;
 }
-int i2c_read(uchar chip, uint addr, int alen, uchar * buffer, int len)
+static int ppc4xx_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+			   int alen, uchar *buffer, int len)
 {
-	return ppc4xx_i2c_transfer(chip, addr, alen, buffer, len, 1);
+	return ppc4xx_i2c_transfer(adap, chip, addr, alen, buffer, len, 1);
 }
-int i2c_write(uchar chip, uint addr, int alen, uchar * buffer, int len)
+static int ppc4xx_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+			    int alen, uchar *buffer, int len)
 {
-	return ppc4xx_i2c_transfer(chip, addr, alen, buffer, len, 0);
+	return ppc4xx_i2c_transfer(adap, chip, addr, alen, buffer, len, 0);
 }
-#if defined(CONFIG_I2C_MULTI_BUS)
-/*
- * Functions for multiple I2C bus handling
- */
-unsigned int i2c_get_bus_num(void)
+static unsigned int ppc4xx_i2c_set_bus_speed(struct i2c_adapter *adap,
+					     unsigned int speed)
 {
-	return i2c_bus_num;
-}
-
-int i2c_set_bus_num(unsigned int bus)
-{
-	if (bus >= CONFIG_SYS_MAX_I2C_BUS)
+	if (speed != adap->speed)
    	return -1;
-
-	i2c_bus_num = bus;
-
-	return 0;
+	return speed;
 }
-#endif	/* CONFIG_I2C_MULTI_BUS */
-#endif	/* CONFIG_HARD_I2C */
+
+/*
+ * Register ppc4xx i2c adapters
+ */
+#ifdef CONFIG_SYS_I2C_PPC4XX_CH0
+U_BOOT_I2C_ADAP_COMPLETE(ppc4xx_0, ppc4xx_i2c_init, ppc4xx_i2c_probe,
+			 ppc4xx_i2c_read, ppc4xx_i2c_write,
+			 ppc4xx_i2c_set_bus_speed,
+			 CONFIG_SYS_I2C_PPC4XX_SPEED_0,
+			 CONFIG_SYS_I2C_PPC4XX_SLAVE_0, 0)
+#endif
+#ifdef CONFIG_SYS_I2C_PPC4XX_CH1
+U_BOOT_I2C_ADAP_COMPLETE(ppc4xx_1, ppc4xx_i2c_init, ppc4xx_i2c_probe,
+			 ppc4xx_i2c_read, ppc4xx_i2c_write,
+			 ppc4xx_i2c_set_bus_speed,
+			 CONFIG_SYS_I2C_PPC4XX_SPEED_1,
+			 CONFIG_SYS_I2C_PPC4XX_SLAVE_1, 1)
+#endif
diff --git a/include/configs/APC405.h b/include/configs/APC405.h
index 9a65cbc..6720445 100644
--- a/include/configs/APC405.h
+++ b/include/configs/APC405.h
@@ -305,10 +305,11 @@
 /*
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08 */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address */
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index 09aa763..a6545c1 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -246,10 +246,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CANBT.h b/include/configs/CANBT.h
index d36cc89..fdff733 100644
--- a/include/configs/CANBT.h
+++ b/include/configs/CANBT.h
@@ -184,10 +184,11 @@
 #define CONFIG_SYS_I2C_SOFT		/* Software I2C support enabled */
 #endif
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h
index 1e3a564..d17adf8 100644
--- a/include/configs/CATcenter.h
+++ b/include/configs/CATcenter.h
@@ -401,10 +401,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h
index 686d158..ca258e6 100644
--- a/include/configs/CMS700.h
+++ b/include/configs/CMS700.h
@@ -226,10 +226,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CPCI2DP.h b/include/configs/CPCI2DP.h
index 11cf58b..8a3eb54 100644
--- a/include/configs/CPCI2DP.h
+++ b/include/configs/CPCI2DP.h
@@ -210,10 +210,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h
index e3e5ebc..4751b8f 100644
--- a/include/configs/CPCI405.h
+++ b/include/configs/CPCI405.h
@@ -259,10 +259,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index c4fff48..6cbee62 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -286,10 +286,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 9122cbd..5a014c4 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -262,10 +262,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC32) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC32		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h
index f778af7..7572f57 100644
--- a/include/configs/CPCI405DT.h
+++ b/include/configs/CPCI405DT.h
@@ -281,10 +281,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CPCIISER4.h b/include/configs/CPCIISER4.h
index 35daed0..854847b 100644
--- a/include/configs/CPCIISER4.h
+++ b/include/configs/CPCIISER4.h
@@ -195,10 +195,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h
index 6bceccb..37139ed 100644
--- a/include/configs/CRAYL1.h
+++ b/include/configs/CRAYL1.h
@@ -76,11 +76,12 @@
  #define CONFIG_SERVERIP         10.0.0.1
  #define CONFIG_ETHADDR          00:40:a6:80:14:5
  */
-#define CONFIG_HARD_I2C         1		/* hardware support for i2c */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
 #define CONFIG_SDRAM_BANK0		1
-#define CONFIG_SYS_I2C_SPEED		    400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		    0x7F
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		    400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		    0x7F
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_IDENT_STRING     "Cray L1"
diff --git a/include/configs/DP405.h b/include/configs/DP405.h
index 6d67d6e..fa09797 100644
--- a/include/configs/DP405.h
+++ b/include/configs/DP405.h
@@ -178,10 +178,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/DU405.h b/include/configs/DU405.h
index 24df85a..26162d1 100644
--- a/include/configs/DU405.h
+++ b/include/configs/DU405.h
@@ -197,10 +197,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/DU440.h b/include/configs/DU440.h
index 09876f5..2de4443 100644
--- a/include/configs/DU440.h
+++ b/include/configs/DU440.h
@@ -170,18 +170,20 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support    */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address  */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_I2C_MULTI_BUS    1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
+#define CONFIG_SYS_I2C_PPC4XX_CH1
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_1		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1		0x7F
#define CONFIG_SYS_SPD_BUS_NUM         0
 #define IIC1_MCP3021_ADDR	0x4d
 #define IIC1_USB2507_ADDR	0x2c
-#ifdef CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_NOPROBES        {{1, IIC1_USB2507_ADDR}}
-#endif
+#define CONFIG_SYS_I2C_NOPROBES		{ {1, IIC1_USB2507_ADDR} }
+
 #define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x54
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
diff --git a/include/configs/G2000.h b/include/configs/G2000.h
index 08ba840..5d8eb77 100644
--- a/include/configs/G2000.h
+++ b/include/configs/G2000.h
@@ -297,10 +297,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
 /* CAT24WC08/16... */
diff --git a/include/configs/HH405.h b/include/configs/HH405.h
index 444413d..1435f03 100644
--- a/include/configs/HH405.h
+++ b/include/configs/HH405.h
@@ -333,14 +333,15 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
 #if 0 /* test-only */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
 #else
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
 #endif
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
 #define CONFIG_SYS_EEPROM_WREN         1
diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index e90782f..ecfc4aa 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -246,10 +246,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/JSE.h b/include/configs/JSE.h
index 713dcca..0ab6864 100644
--- a/include/configs/JSE.h
+++ b/include/configs/JSE.h
@@ -210,10 +210,11 @@
#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
/*-----------------------------------------------------------------------
diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h
index f8da14d..4a60436 100644
--- a/include/configs/KAREF.h
+++ b/include/configs/KAREF.h
@@ -133,13 +133,15 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C	      1		     /* I2C hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED	      400000	     /* I2C speed 400kHz	*/
-#define CONFIG_SYS_I2C_SLAVE	      0x7F	     /* I2C slave address	*/
-#define CONFIG_SYS_I2C_NOPROBES      {0x69}	     /* Don't probe these addrs */
-#define CONFIG_I2C_BUS1	      1		     /* Include i2c bus 1 supp	*/
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+#define CONFIG_SYS_I2C_PPC4XX_CH1
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 /* I2C speed 400kHz */
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F
+#define CONFIG_SYS_I2C_NOPROBES { { 0, 0x69} } /* Don't probe these addrs */
/*-----------------------------------------------------------------------
  * Environment
diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h
index 7556ad5..96f3015 100644
--- a/include/configs/METROBOX.h
+++ b/include/configs/METROBOX.h
@@ -195,13 +195,15 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C	      1		     /* I2C hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED	      400000	     /* I2C speed 400kHz	*/
-#define CONFIG_SYS_I2C_SLAVE	      0x7F	     /* I2C slave address	*/
-#define CONFIG_SYS_I2C_NOPROBES      {0x69}	     /* Don't probe these addrs */
-#define CONFIG_I2C_BUS1	      1		     /* Include i2c bus 1 supp	*/
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+#define CONFIG_SYS_I2C_PPC4XX_CH1
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 /* I2C speed 400kHz */
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F
+#define CONFIG_SYS_I2C_NOPROBES { { 0, 0x69} } /* Don't probe these addrs */
/*-----------------------------------------------------------------------
  * Environment
diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h
index 979495a..831f5c9 100644
--- a/include/configs/MIP405.h
+++ b/include/configs/MIP405.h
@@ -98,10 +98,11 @@
  * The Atmel EEPROM uses 16Bit addressing.
  ***************************************************************/
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		50000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x53	/* EEPROM 24C128/256		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
diff --git a/include/configs/OCRTC.h b/include/configs/OCRTC.h
index 47110af..9b8b701 100644
--- a/include/configs/OCRTC.h
+++ b/include/configs/OCRTC.h
@@ -216,10 +216,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/ORSG.h b/include/configs/ORSG.h
index 9f754c2..8f221f9 100644
--- a/include/configs/ORSG.h
+++ b/include/configs/ORSG.h
@@ -212,10 +212,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/PCI405.h b/include/configs/PCI405.h
index 119819e..687340d 100644
--- a/include/configs/PCI405.h
+++ b/include/configs/PCI405.h
@@ -208,10 +208,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h
index 713ea12..b881609 100644
--- a/include/configs/PIP405.h
+++ b/include/configs/PIP405.h
@@ -87,10 +87,11 @@
  * EEPROM of the SDRAM
  * The Atmel EEPROM uses 16Bit addressing.
  ***************************************************************/
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		50000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x53
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 1ee0c48..7240d00 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -280,10 +280,11 @@
 /*
  * I2C EEPROM (24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM 24WC16 */
 #define CONFIG_SYS_EEPROM_WREN         1
diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h
index 8235b85..6cc8917 100644
--- a/include/configs/PMC405.h
+++ b/include/configs/PMC405.h
@@ -238,10 +238,11 @@
 /*
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24W16 */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address */
diff --git a/include/configs/PMC405DE.h b/include/configs/PMC405DE.h
index 992443a..6ee3a8d 100644
--- a/include/configs/PMC405DE.h
+++ b/include/configs/PMC405DE.h
@@ -216,10 +216,11 @@
 /*
  * I2C EEPROM (24W16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM 24W16	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address */
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h
index 2265d96..470ee69 100644
--- a/include/configs/PMC440.h
+++ b/include/configs/PMC440.h
@@ -225,12 +225,14 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support    */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address  */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-#define CONFIG_I2C_MULTI_BUS	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
+#define CONFIG_SYS_I2C_PPC4XX_CH1
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_1		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1		0x7F
#define CONFIG_SYS_I2C_MULTI_EEPROMS
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
index 27a12b3..82739fe 100644
--- a/include/configs/PPChameleonEVB.h
+++ b/include/configs/PPChameleonEVB.h
@@ -418,10 +418,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h
index f1032f0..46e1674 100644
--- a/include/configs/VOH405.h
+++ b/include/configs/VOH405.h
@@ -279,10 +279,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
 #define CONFIG_SYS_EEPROM_WREN         1
diff --git a/include/configs/VOM405.h b/include/configs/VOM405.h
index 43d6bb3..85722e4 100644
--- a/include/configs/VOM405.h
+++ b/include/configs/VOM405.h
@@ -205,10 +205,11 @@
 /*
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
index 462b155..40cd8f8 100644
--- a/include/configs/W7OLMC.h
+++ b/include/configs/W7OLMC.h
@@ -278,10 +278,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h
index f28f3e4..f419d7e 100644
--- a/include/configs/W7OLMG.h
+++ b/include/configs/W7OLMG.h
@@ -285,10 +285,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (ATMEL 24C04N)
  */
-#define CONFIG_HARD_I2C		1		/* Hardware assisted I2C	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM ATMEL 24C04N		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1		/* Bytes of address		*/
diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h
index 5def36a..97983a6 100644
--- a/include/configs/WUH405.h
+++ b/include/configs/WUH405.h
@@ -243,10 +243,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index 8c447ca..52a64bf 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -206,7 +206,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index a6add6b..99b1290 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -121,11 +121,12 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs	*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x69} }	/* Don't probe these addrs */
/*-----------------------------------------------------------------------
  * I2C EEPROM (PCF8594C)
diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h
index f2f522d..d5dd67c 100644
--- a/include/configs/amcc-common.h
+++ b/include/configs/amcc-common.h
@@ -42,9 +42,10 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
/*
  * Ethernet/EMAC/PHY
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 506a558..910b626 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -222,7 +222,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/bluestone.h b/include/configs/bluestone.h
index 3e691fd..934da81 100644
--- a/include/configs/bluestone.h
+++ b/include/configs/bluestone.h
@@ -122,7 +122,7 @@
 /*
  * I2C
  */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed            */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
 #define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h
index da67ae3..e429ed2 100644
--- a/include/configs/bubinga.h
+++ b/include/configs/bubinga.h
@@ -134,9 +134,9 @@
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#define CONFIG_SYS_I2C_NOPROBES	{ 0x69 }	/* avoid i2c probe hangup (why?) */
+#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x69} }	/* avoid i2c probe hangup (?) */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
#if defined(CONFIG_CMD_EEPROM)
diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h
index acb127c..61dbda6 100644
--- a/include/configs/canyonlands.h
+++ b/include/configs/canyonlands.h
@@ -329,7 +329,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed			*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR		(0xa8>>1)
diff --git a/include/configs/csb272.h b/include/configs/csb272.h
index f21fa64..d1a1d2a 100644
--- a/include/configs/csb272.h
+++ b/include/configs/csb272.h
@@ -175,10 +175,11 @@
  * I2C configuration
  *
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed			*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F	/* I2C slave address */
/*
  * MII PHY configuration
diff --git a/include/configs/csb472.h b/include/configs/csb472.h
index aed5fa6..4cd0057 100644
--- a/include/configs/csb472.h
+++ b/include/configs/csb472.h
@@ -174,10 +174,11 @@
  * I2C configuration
  *
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed			*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F	/* I2C slave address */
/*
  * MII PHY configuration
diff --git a/include/configs/dlvision-10g.h b/include/configs/dlvision-10g.h
index 2cd2027..5d6308f 100644
--- a/include/configs/dlvision-10g.h
+++ b/include/configs/dlvision-10g.h
@@ -114,7 +114,7 @@
 /*
  * I2C stuff
  */
-#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
/* Temp sensor/hwmon/dtt */
 #define CONFIG_DTT_LM63		1	/* National LM63	*/
diff --git a/include/configs/dlvision.h b/include/configs/dlvision.h
index c490ff6..24c9fa4 100644
--- a/include/configs/dlvision.h
+++ b/include/configs/dlvision.h
@@ -107,7 +107,7 @@
 /*
  * I2C stuff
  */
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
/*
  * FLASH organization
diff --git a/include/configs/ebony.h b/include/configs/ebony.h
index d6b6551..bb56d0f 100644
--- a/include/configs/ebony.h
+++ b/include/configs/ebony.h
@@ -138,7 +138,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/gdppc440etx.h b/include/configs/gdppc440etx.h
index 9efbb8e..ab35901 100644
--- a/include/configs/gdppc440etx.h
+++ b/include/configs/gdppc440etx.h
@@ -145,7 +145,7 @@
 /*
  * I2C
  */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed+slave address*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
/*
  * Default environment variables
diff --git a/include/configs/icon.h b/include/configs/icon.h
index 2fac0ef..a55a851 100644
--- a/include/configs/icon.h
+++ b/include/configs/icon.h
@@ -120,9 +120,8 @@
 /*
  * I2C
  */
-#define CONFIG_SYS_I2C_SPEED	100000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0	100000
-#define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_SPD_BUS_NUM	0	/* The I2C bus for SPD		*/
#define CONFIG_SYS_I2C_MULTI_EEPROMS
diff --git a/include/configs/intip.h b/include/configs/intip.h
index 33364a8..04451b3 100644
--- a/include/configs/intip.h
+++ b/include/configs/intip.h
@@ -228,7 +228,7 @@
 /*
  * I2C
  */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR		(0xa8>>1)
diff --git a/include/configs/io.h b/include/configs/io.h
index 03661cc..4950ad7 100644
--- a/include/configs/io.h
+++ b/include/configs/io.h
@@ -114,7 +114,7 @@
 /*
  * I2C stuff
  */
-#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
/* Temp sensor/hwmon/dtt */
 #define CONFIG_DTT_LM63		1	/* National LM63	*/
diff --git a/include/configs/io64.h b/include/configs/io64.h
index 887aaef..bb29bed 100644
--- a/include/configs/io64.h
+++ b/include/configs/io64.h
@@ -340,7 +340,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0	400000
#define CONFIG_PCA9698		1	/* NXP PCA9698 */
diff --git a/include/configs/iocon.h b/include/configs/iocon.h
index 695aa5c..5972711 100644
--- a/include/configs/iocon.h
+++ b/include/configs/iocon.h
@@ -110,11 +110,11 @@
 /*
  * I2C stuff
  */
-#undef CONFIG_HARD_I2C
 #define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	400000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
/*
  * Software (bit-bang) I2C driver configuration
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 3ed8dc7..5b3ad74 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -119,9 +119,8 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
-#define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_SPD_BUS_NUM		0	/* The I2C bus for SPD		*/
#define IIC0_BOOTPROM_ADDR	0x50
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index d505a41..4af908d 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -385,7 +385,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
diff --git a/include/configs/korat.h b/include/configs/korat.h
index 7d5fb15..5744db3 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -155,10 +155,11 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/luan.h b/include/configs/luan.h
index 3b4761b..ed275a1 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -134,7 +134,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index fec0d55..868e5c9 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -280,10 +280,11 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C				/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_RTC_ADDR	0x51	/* RTC				*/
 #define CONFIG_SYS_I2C_EEPROM_CPU_ADDR	0x52	/* EEPROM          (CPU Modul)	*/
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index 6c1b136..5baba18 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -201,7 +201,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
diff --git a/include/configs/neo.h b/include/configs/neo.h
index 38b5bec..be1c9ff 100644
--- a/include/configs/neo.h
+++ b/include/configs/neo.h
@@ -117,7 +117,7 @@
 /*
  * I2C stuff
  */
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
/* RTC */
 #define CONFIG_RTC_DS1337
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index d0fe9da..de021e3 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -151,7 +151,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h
index ba10e88..4c9fb6f 100644
--- a/include/configs/p3p440.h
+++ b/include/configs/p3p440.h
@@ -97,11 +97,12 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs	*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x69} }	/* Don't probe these addrs */
/*-----------------------------------------------------------------------
  * I2C RTC
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index 8d46607..51e26be 100644
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -139,10 +139,11 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa4>>1)
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h
index 30a8c55..809d764 100644
--- a/include/configs/quad100hd.h
+++ b/include/configs/quad100hd.h
@@ -152,10 +152,11 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* base address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2		/* bytes of address */
diff --git a/include/configs/redwood.h b/include/configs/redwood.h
index f75ab67..355c330 100644
--- a/include/configs/redwood.h
+++ b/include/configs/redwood.h
@@ -110,13 +110,13 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed			*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define IIC0_BOOTPROM_ADDR	0x50
 #define IIC0_ALT_BOOTPROM_ADDR	0x54
/* Don't probe these addrs */
-#define CONFIG_SYS_I2C_NOPROBES	{0x50, 0x52, 0x53, 0x54}
+#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x50}, {0, 0x52}, {0, 0x53}, {0, 0x54} }
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
diff --git a/include/configs/sbc405.h b/include/configs/sbc405.h
index 9918638..2342d7c 100644
--- a/include/configs/sbc405.h
+++ b/include/configs/sbc405.h
@@ -168,10 +168,11 @@
#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
/*-----------------------------------------------------------------------
  * PCI stuff
diff --git a/include/configs/sc3.h b/include/configs/sc3.h
index abca9e0..cabe45e 100644
--- a/include/configs/sc3.h
+++ b/include/configs/sc3.h
@@ -246,15 +246,16 @@
  * IIC stuff
  *-----------------------------------------------------------------------
  */
-#define  CONFIG_HARD_I2C		/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
+#define  CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
#define I2C_INIT
 #define I2C_ACTIVE 0
 #define I2C_TRISTATE 0
-#define CONFIG_SYS_I2C_SPEED		100000	/* use the standard 100kHz speed */
-#define CONFIG_SYS_I2C_SLAVE		0x7F		/* mask valid bits */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F	/* mask valid bits */
#define CONFIG_RTC_DS1337
 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index dd5d7cd..3b8a0c6 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -232,7 +232,7 @@
 /*
  * I2C
  */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/t3corp.h b/include/configs/t3corp.h
index 2a731a6..a129013 100644
--- a/include/configs/t3corp.h
+++ b/include/configs/t3corp.h
@@ -319,7 +319,7 @@
 /*
  * I2C
  */
-#define CONFIG_SYS_I2C_SPEED			400000	/* I2C speed */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0			400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR		(0xa8>>1)
diff --git a/include/configs/taihu.h b/include/configs/taihu.h
index a3738b7..9bc247d 100644
--- a/include/configs/taihu.h
+++ b/include/configs/taihu.h
@@ -138,9 +138,9 @@
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#define CONFIG_SYS_I2C_NOPROBES	{ 0x69 } /* avoid i2c probe hangup (why?) */
+#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x69} } /* avoid i2c probe hangup (?) */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	6 /* 24C02 requires 5ms delay */
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* I2C boot EEPROM (24C02W)	*/
diff --git a/include/configs/taishan.h b/include/configs/taishan.h
index 3046081..a80eccc 100644
--- a/include/configs/taishan.h
+++ b/include/configs/taishan.h
@@ -133,7 +133,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#undef CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
diff --git a/include/configs/walnut.h b/include/configs/walnut.h
index d10f748..7b97f13 100644
--- a/include/configs/walnut.h
+++ b/include/configs/walnut.h
@@ -95,7 +95,7 @@
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/xpedite1000.h b/include/configs/xpedite1000.h
index 506d646..8077e39 100644
--- a/include/configs/xpedite1000.h
+++ b/include/configs/xpedite1000.h
@@ -145,11 +145,11 @@ extern void out32(unsigned int, unsigned long);
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C			1	/* I2C with hardware support */
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7f
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7f
/* I2C EEPROM */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index 0cbef6f..c0b0177 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -137,7 +137,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index fb684b5..7311c2d 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -120,13 +120,13 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define IIC0_BOOTPROM_ADDR	0x50
 #define IIC0_ALT_BOOTPROM_ADDR	0x54
/* Don't probe these addrs */
-#define CONFIG_SYS_I2C_NOPROBES	{0x50, 0x52, 0x53, 0x54}
+#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x50}, {0, 0x52}, {0, 0x53}, {0, 0x54} }
/* #if defined(CONFIG_CMD_EEPROM) */
 /* #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50 */	/* I2C boot EEPROM		*/
diff --git a/include/configs/zeus.h b/include/configs/zeus.h
index 75195bc..b653993 100644
--- a/include/configs/zeus.h
+++ b/include/configs/zeus.h
@@ -168,10 +168,11 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
/* these are for the ST M24C02 2kbit serial i2c eeprom */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* base address */
-- 
1.7.2.5


    

[U-Boot] [PATCH 01/16] i2c, ppc4xx_i2c: switch to new multibus/multiadapter support

Dirk Eibach

Heiko Schocher

tags (0)

participants (2)