[PATCH v5 00/28] arm: dts: ls1028a: sync device tree with linux
This series sync the device tree of the LS1028A SoC with the linux one. To ease future debugging and reviewing, we first clean up the existing one, removing bogus nodes, moving all CCSR related nodes in /soc and update the drivers to accept the offical compatible strings.
This was tested on a sl28 board, but the ls1028a.dtsi sync also affects the LS1028A-RDB and -QDS. It would be nice if someone could actually test it on such a board.
I didn't sync the device trees for the NXP boards because u-boot related things aren't split into its own -u-boot.dtsi file. So I'll leave that task to NXP :)
The following patch is a prerequisite for this series: https://patchwork.ozlabs.org/project/uboot/patch/20210825210510.24766-1-trin...
changes since v4: - drop the following patch which isn't needed anymore, because it was fixed in the linux dtsi: arm: dts: ls1028a: drop non-removable property from esdhc controller - sync dtsi with linux 5.14.12
changes since v3: - rebase to latest master - don't support fsl,ls1028a-gpu anymore, use the upstream compatible string
changes since v2: - move the device tree nodes piece by piece and sort them to ease reviewing - fix PCI driver (bindings) - fix SATA driver (bindings) - fix USB driver (bindings) - split most changes which are caused by the sync of the linux device tree to own patches, eg. pcie io window, spi chip selects
The final diff for the sync is much nicer now ;)
changes since v1: - remove u-boot,dm-pre-reloc from rdb and qds boards - fix enetc0 and enetc2 labels
Michael Walle (28): armv8: ls1028a: use the official compatible string for the GPU arm: dts: ls1028a: remove /memory node arm: dts: ls1028a-{rdb,qds}: remove dm-pre-reloc property arm: dts: ls1028a: add an empty /soc arm: dts: ls1028a: move the clockgen node into /soc arm: dts: ls1028a: move I2C controller nodes into /soc arm: dts: ls1028a: move the FlexSPI controller node arm: dts: ls1028a: move the SPI and eSDHC controller nodes into /soc arm: dts: ls1028a: move the UART controller nodes into /soc arm: dts: ls1028a: move the low-power UART nodes into /soc arm: dts: ls1028a: move the GPIO controller nodes into /soc arm: dts: ls1028a: move SATA and USB controller nodes into /soc arm: dts: ls1028a: move the PCIe controller nodes into /soc arm: dts: ls1028a: move the watchdog node into /soc arm: dts: ls1028a: move the iRC node and its devices into /soc arm: dts: ls1028a: update the labels watchdog: sp805_wdt: use correct compatible string spi: fsl_dspi: add new compatible fsl,ls1021a-v1.0-dspi spi: fsl_dspi: rename num-cs to spi-num-chipselects serial: lpuart: add new compatible fsl,ls1028a-lpuart scsi: ceva: rename the resource name to match the linux kernel one usb: xhci: fsl: add new compatible fsl,ls1028a-dwc3 pci: layerscape: add official ls1028a binding support arm: dts: ls1028a: remove num-lanes in the PCIe controller nodes arm: dts: ls1028a: move the PCI I/O window to match arm: dts: ls1028a: disable the PCIe controller by default arm: dts: ls1028a: sync the fsl-ls1028a.dtsi with linux arm: dts: sl28: sync dtbs
arch/arm/cpu/armv8/fsl-layerscape/fdt.c | 2 +- .../arm/cpu/armv8/fsl-layerscape/ls1028_ids.c | 2 +- arch/arm/dts/fsl-ls1012a.dtsi | 4 +- .../dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi | 37 +- .../fsl-ls1028a-kontron-sl28-var1-u-boot.dtsi | 2 +- .../arm/dts/fsl-ls1028a-kontron-sl28-var1.dts | 31 +- .../fsl-ls1028a-kontron-sl28-var2-u-boot.dtsi | 8 + .../arm/dts/fsl-ls1028a-kontron-sl28-var2.dts | 46 +- .../fsl-ls1028a-kontron-sl28-var3-u-boot.dtsi | 2 +- .../fsl-ls1028a-kontron-sl28-var4-u-boot.dtsi | 4 +- .../arm/dts/fsl-ls1028a-kontron-sl28-var4.dts | 18 +- arch/arm/dts/fsl-ls1028a-kontron-sl28.dts | 256 ++- .../dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi | 4 +- .../dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi | 4 +- .../dts/fsl-ls1028a-qds-7777-sch-30841.dtsi | 12 +- .../dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi | 8 +- .../dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi | 4 +- .../fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi | 12 +- .../dts/fsl-ls1028a-qds-9999-sch-24801.dtsi | 12 +- arch/arm/dts/fsl-ls1028a-qds-duart.dts | 2 +- .../fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi | 12 +- .../fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi | 12 +- .../dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi | 6 +- .../dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi | 6 +- arch/arm/dts/fsl-ls1028a-qds.dtsi | 25 +- arch/arm/dts/fsl-ls1028a-rdb.dts | 31 +- arch/arm/dts/fsl-ls1028a.dtsi | 1443 ++++++++++++----- arch/arm/dts/fsl-ls1043a.dtsi | 6 +- arch/arm/dts/fsl-ls1046a.dtsi | 6 +- arch/arm/dts/fsl-ls1088a.dtsi | 4 +- arch/arm/dts/fsl-ls2080a.dtsi | 2 +- arch/arm/dts/fsl-lx2160a.dtsi | 6 +- arch/arm/dts/hi3660.dtsi | 4 +- arch/arm/dts/ls1021a.dtsi | 6 +- arch/arm/dts/vf.dtsi | 4 +- drivers/ata/sata_ceva.c | 2 +- drivers/pci/pcie_layerscape_rc.c | 61 +- drivers/serial/serial_lpuart.c | 2 + drivers/spi/fsl_dspi.c | 6 +- drivers/usb/host/xhci-fsl.c | 1 + drivers/watchdog/sp805_wdt.c | 2 +- .../dt-bindings/clock/fsl,qoriq-clockgen.h | 15 + 42 files changed, 1530 insertions(+), 602 deletions(-) create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.h
There is no "fsl,ls1028a-gpu" compatible string. It is solely for the proprietary driver which will never be open source. Lately, linux gained support for the open source etnaviv driver for the GPU (although there is still support for the DisplayPort PHY missing to get actual graphics output). Thus, instead of supporting some proprietary driver, switch over to the open source one, which also have an official device tree binding.
Cc: Andy Tang andy.tang@nxp.com Signed-off-by: Michael Walle michael@walle.cc --- For reference: https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git/commit/?h...
arch/arm/cpu/armv8/fsl-layerscape/fdt.c | 2 +- arch/arm/cpu/armv8/fsl-layerscape/ls1028_ids.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fdt.c b/arch/arm/cpu/armv8/fsl-layerscape/fdt.c index 6eb7f9c214..4ec0dbf516 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/fdt.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/fdt.c @@ -427,7 +427,7 @@ static void fdt_disable_multimedia(void *blob, unsigned int svr) fdt_status_disabled(blob, off);
/* Disable GPU node */ - off = fdt_node_offset_by_compatible(blob, -1, "fsl,ls1028a-gpu"); + off = fdt_node_offset_by_compatible(blob, -1, "vivante,gc"); if (off != -FDT_ERR_NOTFOUND) fdt_status_disabled(blob, off); } diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1028_ids.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1028_ids.c index 49df8b3790..86a49b152e 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/ls1028_ids.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1028_ids.c @@ -18,7 +18,7 @@ struct icid_id_table icid_tbl[] = { SET_SATA_ICID(1, "fsl,ls1028a-ahci", FSL_SATA1_STREAM_ID), SET_EDMA_ICID(FSL_EDMA_STREAM_ID), SET_QDMA_ICID("fsl,ls1028a-qdma", FSL_DMA_STREAM_ID), - SET_GPU_ICID("fsl,ls1028a-gpu", FSL_GPU_STREAM_ID), + SET_GPU_ICID("vivante,gc", FSL_GPU_STREAM_ID), SET_DISPLAY_ICID(FSL_DISPLAY_STREAM_ID), #ifdef CONFIG_FSL_CAAM SET_SEC_JR_ICID_ENTRY(0, FSL_SEC_JR1_STREAM_ID),
This node is some hodgepodge between the ddr controller node at SoC offset 0x1080000 and some static memory size of 2GiB. Remove this bogus node because it doesn't seem to be used at all.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com Tested-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 6 ------ 1 file changed, 6 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 53b052ed32..48f70c10d9 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -28,12 +28,6 @@ clocks = <&sysclk>; };
- memory@01080000 { - device_type = "memory"; - reg = <0x00000000 0x01080000 0 0x80000000>; - /* DRAM space - 1, size : 2 GB DRAM */ - }; - gic: interrupt-controller@6000000 { compatible = "arm,gic-v3"; reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
Nowadays, both boards boot using the TF-A BL1/BL2 and SPL isn't used at all. The property is not needed, remove it.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a-qds.dtsi | 1 - arch/arm/dts/fsl-ls1028a-rdb.dts | 1 - 2 files changed, 2 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a-qds.dtsi b/arch/arm/dts/fsl-ls1028a-qds.dtsi index 69632fa796..335d7b1e4c 100644 --- a/arch/arm/dts/fsl-ls1028a-qds.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds.dtsi @@ -130,7 +130,6 @@
&i2c0 { status = "okay"; - u-boot,dm-pre-reloc;
fpga@66 { #address-cells = <1>; diff --git a/arch/arm/dts/fsl-ls1028a-rdb.dts b/arch/arm/dts/fsl-ls1028a-rdb.dts index 82a8c0a0cd..708182f65c 100644 --- a/arch/arm/dts/fsl-ls1028a-rdb.dts +++ b/arch/arm/dts/fsl-ls1028a-rdb.dts @@ -61,7 +61,6 @@
&i2c0 { status = "okay"; - u-boot,dm-pre-reloc;
i2c-mux@77 {
To keep the device tree similar to the linux kernel one, we need to move all CCSR related devices into the /soc node. To keep the patches easy to review, we initially add an empty /soc node and populate it piece by piece.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi | 4 ++++ arch/arm/dts/fsl-ls1028a.dtsi | 7 +++++++ 2 files changed, 11 insertions(+)
diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi index b3861ed98c..fa4c05212a 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi @@ -266,6 +266,10 @@ u-boot,dm-pre-reloc; };
+&soc { + u-boot,dm-pre-reloc; +}; + &sysclk { u-boot,dm-pre-reloc; }; diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 48f70c10d9..1f562cfdad 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -478,4 +478,11 @@ compatible = "arm,sp805-wdt"; reg = <0x0 0xc000000 0x0 0x1000>; }; + + soc: soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + }; };
Populate the /soc node with the first device node.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 1f562cfdad..54f97014be 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -21,13 +21,6 @@ clock-output-names = "sysclk"; };
- clockgen: clocking@1300000 { - compatible = "fsl,ls1028a-clockgen"; - reg = <0x0 0x1300000 0x0 0xa0000>; - #clock-cells = <2>; - clocks = <&sysclk>; - }; - gic: interrupt-controller@6000000 { compatible = "arm,gic-v3"; reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ @@ -484,5 +477,12 @@ #address-cells = <2>; #size-cells = <2>; ranges; + + clockgen: clocking@1300000 { + compatible = "fsl,ls1028a-clockgen"; + reg = <0x0 0x1300000 0x0 0xa0000>; + #clock-cells = <2>; + clocks = <&sysclk>; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- .../dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi | 2 +- .../dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi | 2 +- .../dts/fsl-ls1028a-qds-7777-sch-30841.dtsi | 8 +- .../dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi | 4 +- .../dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi | 2 +- .../fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi | 8 +- .../dts/fsl-ls1028a-qds-9999-sch-24801.dtsi | 8 +- .../fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi | 8 +- .../fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi | 8 +- .../dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi | 2 +- .../dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi | 2 +- arch/arm/dts/fsl-ls1028a.dtsi | 176 +++++++++--------- 12 files changed, 115 insertions(+), 115 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi index 4063d9a114..1f13cf80e6 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi @@ -16,5 +16,5 @@ &enetc0 { status = "okay"; phy-mode = "usxgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi index 548ab2ba65..10375b2751 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi @@ -15,5 +15,5 @@ &enetc0 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi b/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi index 3991fb793f..f18cb39f21 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi @@ -31,25 +31,25 @@ &mscc_felix_port0 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@00}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@00}>; };
&mscc_felix_port1 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@01}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@01}>; };
&mscc_felix_port2 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; };
&mscc_felix_port3 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@03}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@03}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi b/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi index d68c8c2be0..f6561a89eb 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi @@ -20,13 +20,13 @@ &mscc_felix_port0 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; };
&mscc_felix_port3 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@03}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@03}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi b/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi index 94b5081d61..d9ccd8353b 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi @@ -15,5 +15,5 @@ &enetc0 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi index 3b850268e6..0630f12069 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi @@ -45,25 +45,25 @@ &mscc_felix_port0 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>; };
&mscc_felix_port1 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@1c}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@1c}>; };
&mscc_felix_port2 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>; };
&mscc_felix_port3 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi index eb632143e0..170aacf8c0 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi @@ -30,25 +30,25 @@ &mscc_felix_port0 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>; };
&mscc_felix_port1 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1d}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1d}>; };
&mscc_felix_port2 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>; };
&mscc_felix_port3 { status = "okay"; phy-mode = "sgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi index ed86da6b26..1a9288a037 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi @@ -30,25 +30,25 @@ &mscc_felix_port0 { status = "okay"; phy-mode = "usxgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@00}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@00}>; };
&mscc_felix_port1 { status = "okay"; phy-mode = "usxgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@01}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@01}>; };
&mscc_felix_port2 { status = "okay"; phy-mode = "usxgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@02}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@02}>; };
&mscc_felix_port3 { status = "okay"; phy-mode = "usxgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@03}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@03}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi index c9de4ecc43..544f548b1a 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi @@ -24,25 +24,25 @@ &mscc_felix_port0 { status = "okay"; phy-mode = "qsgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@08}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@08}>; };
&mscc_felix_port1 { status = "okay"; phy-mode = "qsgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@09}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@09}>; };
&mscc_felix_port2 { status = "okay"; phy-mode = "qsgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0a}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0a}>; };
&mscc_felix_port3 { status = "okay"; phy-mode = "qsgmii"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0b}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0b}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi index 7f785507bf..639796263c 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi @@ -20,7 +20,7 @@ &mscc_felix_port1 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@02}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@02}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi index 0fbe7721c8..62c5513c2c 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi @@ -20,7 +20,7 @@ &mscc_felix_port2 { status = "okay"; phy-mode = "2500base-x"; - phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@60/phy@02}>; + phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@60/phy@02}>; };
&mscc_felix_port4 { diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 54f97014be..de85fdd045 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -203,94 +203,6 @@ }; };
- i2c0: i2c@2000000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2000000 0x0 0x10000>; - interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - - i2c1: i2c@2010000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2010000 0x0 0x10000>; - interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - - i2c2: i2c@2020000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2020000 0x0 0x10000>; - interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - - i2c3: i2c@2030000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2030000 0x0 0x10000>; - interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - - i2c4: i2c@2040000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2040000 0x0 0x10000>; - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - - i2c5: i2c@2050000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2050000 0x0 0x10000>; - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - - i2c6: i2c@2060000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2060000 0x0 0x10000>; - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - - i2c7: i2c@2070000 { - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2070000 0x0 0x10000>; - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; - status = "disabled"; - }; - lpuart0: serial@2260000 { compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2260000 0x0 0x1000>; @@ -484,5 +396,93 @@ #clock-cells = <2>; clocks = <&sysclk>; }; + + i2c0: i2c@2000000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2000000 0x0 0x10000>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + i2c1: i2c@2010000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2010000 0x0 0x10000>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + i2c2: i2c@2020000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2020000 0x0 0x10000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + i2c3: i2c@2030000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2030000 0x0 0x10000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + i2c4: i2c@2040000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2040000 0x0 0x10000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + i2c5: i2c@2050000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2050000 0x0 0x10000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + i2c6: i2c@2060000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2060000 0x0 0x10000>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + i2c7: i2c@2070000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2070000 0x0 0x10000>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c"; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; }; };
While inserting it into the new location, keep it sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index de85fdd045..6d80b32816 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -43,19 +43,6 @@ IRQ_TYPE_LEVEL_LOW)>; };
- fspi: flexspi@20c0000 { - compatible = "nxp,lx2160a-fspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x20c0000 0x0 0x10000>, - <0x0 0x20000000 0x0 0x10000000>; - reg-names = "fspi_base", "fspi_mmap"; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "fspi_en", "fspi"; - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - serial0: serial@21c0500 { device_type = "serial"; compatible = "fsl,ns16550", "ns16550a"; @@ -484,5 +471,18 @@ clocks = <&clockgen 4 0>; status = "disabled"; }; + + fspi: flexspi@20c0000 { + compatible = "nxp,lx2160a-fspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x20c0000 0x0 0x10000>, + <0x0 0x20000000 0x0 0x10000000>; + reg-names = "fspi_base", "fspi_mmap"; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 116 +++++++++++++++++----------------- 1 file changed, 58 insertions(+), 58 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 6d80b32816..ecafa67d08 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -266,64 +266,6 @@ status = "disabled"; };
- dspi0: dspi@2100000 { - compatible = "fsl,vf610-dspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2100000 0x0 0x10000>; - interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "dspi"; - clocks = <&clockgen 4 0>; - num-cs = <5>; - litte-endian; - status = "disabled"; - }; - - dspi1: dspi@2110000 { - compatible = "fsl,vf610-dspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2110000 0x0 0x10000>; - interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "dspi"; - clocks = <&clockgen 4 0>; - num-cs = <5>; - little-endian; - status = "disabled"; - }; - - dspi2: dspi@2120000 { - compatible = "fsl,vf610-dspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2120000 0x0 0x10000>; - interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "dspi"; - clocks = <&clockgen 4 0>; - num-cs = <5>; - little-endian; - status = "disabled"; - }; - - esdhc0: esdhc@2140000 { - compatible = "fsl,esdhc"; - reg = <0x0 0x2140000 0x0 0x10000>; - interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - big-endian; - bus-width = <4>; - status = "disabled"; - }; - - esdhc1: esdhc@2150000 { - compatible = "fsl,esdhc"; - reg = <0x0 0x2150000 0x0 0x10000>; - interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; - big-endian; - non-removable; - bus-width = <4>; - status = "disabled"; - }; - gpio0: gpio@2300000 { compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2300000 0x0 0x10000>; @@ -484,5 +426,63 @@ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; + + dspi0: dspi@2100000 { + compatible = "fsl,vf610-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2100000 0x0 0x10000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dspi"; + clocks = <&clockgen 4 0>; + num-cs = <5>; + litte-endian; + status = "disabled"; + }; + + dspi1: dspi@2110000 { + compatible = "fsl,vf610-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2110000 0x0 0x10000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dspi"; + clocks = <&clockgen 4 0>; + num-cs = <5>; + little-endian; + status = "disabled"; + }; + + dspi2: dspi@2120000 { + compatible = "fsl,vf610-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2120000 0x0 0x10000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dspi"; + clocks = <&clockgen 4 0>; + num-cs = <5>; + little-endian; + status = "disabled"; + }; + + esdhc0: esdhc@2140000 { + compatible = "fsl,esdhc"; + reg = <0x0 0x2140000 0x0 0x10000>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + big-endian; + bus-width = <4>; + status = "disabled"; + }; + + esdhc1: esdhc@2150000 { + compatible = "fsl,esdhc"; + reg = <0x0 0x2150000 0x0 0x10000>; + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + big-endian; + non-removable; + bus-width = <4>; + status = "disabled"; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index ecafa67d08..07aeb380ef 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -43,22 +43,6 @@ IRQ_TYPE_LEVEL_LOW)>; };
- serial0: serial@21c0500 { - device_type = "serial"; - compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0500 0x0 0x100>; - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - serial1: serial@21c0600 { - device_type = "serial"; - compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0600 0x0 0x100>; - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - pcie1: pcie@3400000 { compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; reg = <0x00 0x03400000 0x0 0x80000 @@ -484,5 +468,21 @@ bus-width = <4>; status = "disabled"; }; + + serial0: serial@21c0500 { + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0500 0x0 0x100>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + serial1: serial@21c0600 { + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0600 0x0 0x100>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 120 +++++++++++++++++----------------- 1 file changed, 60 insertions(+), 60 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 07aeb380ef..349c4bf862 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -174,66 +174,6 @@ }; };
- lpuart0: serial@2260000 { - compatible = "fsl,ls1021a-lpuart"; - reg = <0x0 0x2260000 0x0 0x1000>; - interrupts = <0 232 0x4>; - clocks = <&sysclk>; - clock-names = "ipg"; - little-endian; - status = "disabled"; - }; - - lpuart1: serial@2270000 { - compatible = "fsl,ls1021a-lpuart"; - reg = <0x0 0x2270000 0x0 0x1000>; - interrupts = <0 233 0x4>; - clocks = <&sysclk>; - clock-names = "ipg"; - little-endian; - status = "disabled"; - }; - - lpuart2: serial@2280000 { - compatible = "fsl,ls1021a-lpuart"; - reg = <0x0 0x2280000 0x0 0x1000>; - interrupts = <0 234 0x4>; - clocks = <&sysclk>; - clock-names = "ipg"; - little-endian; - status = "disabled"; - }; - - lpuart3: serial@2290000 { - compatible = "fsl,ls1021a-lpuart"; - reg = <0x0 0x2290000 0x0 0x1000>; - interrupts = <0 235 0x4>; - clocks = <&sysclk>; - clock-names = "ipg"; - little-endian; - status = "disabled"; - }; - - lpuart4: serial@22a0000 { - compatible = "fsl,ls1021a-lpuart"; - reg = <0x0 0x22a0000 0x0 0x1000>; - interrupts = <0 236 0x4>; - clocks = <&sysclk>; - clock-names = "ipg"; - little-endian; - status = "disabled"; - }; - - lpuart5: serial@22b0000 { - compatible = "fsl,ls1021a-lpuart"; - reg = <0x0 0x22b0000 0x0 0x1000>; - interrupts = <0 237 0x4>; - clocks = <&sysclk>; - clock-names = "ipg"; - little-endian; - status = "disabled"; - }; - usb1: usb3@3100000 { compatible = "fsl,layerscape-dwc3"; reg = <0x0 0x3100000 0x0 0x10000>; @@ -484,5 +424,65 @@ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; + + lpuart0: serial@2260000 { + compatible = "fsl,ls1021a-lpuart"; + reg = <0x0 0x2260000 0x0 0x1000>; + interrupts = <0 232 0x4>; + clocks = <&sysclk>; + clock-names = "ipg"; + little-endian; + status = "disabled"; + }; + + lpuart1: serial@2270000 { + compatible = "fsl,ls1021a-lpuart"; + reg = <0x0 0x2270000 0x0 0x1000>; + interrupts = <0 233 0x4>; + clocks = <&sysclk>; + clock-names = "ipg"; + little-endian; + status = "disabled"; + }; + + lpuart2: serial@2280000 { + compatible = "fsl,ls1021a-lpuart"; + reg = <0x0 0x2280000 0x0 0x1000>; + interrupts = <0 234 0x4>; + clocks = <&sysclk>; + clock-names = "ipg"; + little-endian; + status = "disabled"; + }; + + lpuart3: serial@2290000 { + compatible = "fsl,ls1021a-lpuart"; + reg = <0x0 0x2290000 0x0 0x1000>; + interrupts = <0 235 0x4>; + clocks = <&sysclk>; + clock-names = "ipg"; + little-endian; + status = "disabled"; + }; + + lpuart4: serial@22a0000 { + compatible = "fsl,ls1021a-lpuart"; + reg = <0x0 0x22a0000 0x0 0x1000>; + interrupts = <0 236 0x4>; + clocks = <&sysclk>; + clock-names = "ipg"; + little-endian; + status = "disabled"; + }; + + lpuart5: serial@22b0000 { + compatible = "fsl,ls1021a-lpuart"; + reg = <0x0 0x22b0000 0x0 0x1000>; + interrupts = <0 237 0x4>; + clocks = <&sysclk>; + clock-names = "ipg"; + little-endian; + status = "disabled"; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 66 +++++++++++++++++------------------ 1 file changed, 33 insertions(+), 33 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 349c4bf862..9f466554e9 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -190,39 +190,6 @@ status = "disabled"; };
- gpio0: gpio@2300000 { - compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; - reg = <0x0 0x2300000 0x0 0x10000>; - interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - little-endian; - }; - - gpio1: gpio@2310000 { - compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; - reg = <0x0 0x2310000 0x0 0x10000>; - interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - little-endian; - }; - - gpio2: gpio@2320000 { - compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; - reg = <0x0 0x2320000 0x0 0x10000>; - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - little-endian; - }; - sata: sata@3200000 { compatible = "fsl,ls1028a-ahci"; reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ @@ -484,5 +451,38 @@ little-endian; status = "disabled"; }; + + gpio0: gpio@2300000 { + compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + little-endian; + }; + + gpio1: gpio@2310000 { + compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; + reg = <0x0 0x2310000 0x0 0x10000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + little-endian; + }; + + gpio2: gpio@2320000 { + compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; + reg = <0x0 0x2320000 0x0 0x10000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + little-endian; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 50 +++++++++++++++++------------------ 1 file changed, 25 insertions(+), 25 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 9f466554e9..7d18085615 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -174,31 +174,6 @@ }; };
- usb1: usb3@3100000 { - compatible = "fsl,layerscape-dwc3"; - reg = <0x0 0x3100000 0x0 0x10000>; - interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; - dr_mode = "host"; - status = "disabled"; - }; - - usb2: usb3@3110000 { - compatible = "fsl,layerscape-dwc3"; - reg = <0x0 0x3110000 0x0 0x10000>; - interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; - dr_mode = "host"; - status = "disabled"; - }; - - sata: sata@3200000 { - compatible = "fsl,ls1028a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ - 0x7 0x100520 0x0 0x4>; /* ecc sata addr*/ - reg-names = "sata-base", "ecc-addr"; - interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - cluster1_core0_watchdog: wdt@c000000 { compatible = "arm,sp805-wdt"; reg = <0x0 0xc000000 0x0 0x1000>; @@ -484,5 +459,30 @@ #interrupt-cells = <2>; little-endian; }; + + usb1: usb3@3100000 { + compatible = "fsl,layerscape-dwc3"; + reg = <0x0 0x3100000 0x0 0x10000>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + status = "disabled"; + }; + + usb2: usb3@3110000 { + compatible = "fsl,layerscape-dwc3"; + reg = <0x0 0x3110000 0x0 0x10000>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + status = "disabled"; + }; + + sata: sata@3200000 { + compatible = "fsl,ls1028a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ + 0x7 0x100520 0x0 0x4>; /* ecc sata addr*/ + reg-names = "sata-base", "ecc-addr"; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
While at it fix the indentation.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 64 +++++++++++++++++------------------ 1 file changed, 32 insertions(+), 32 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 7d18085615..d0f90941b9 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -43,38 +43,6 @@ IRQ_TYPE_LEVEL_LOW)>; };
- pcie1: pcie@3400000 { - compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; - reg = <0x00 0x03400000 0x0 0x80000 - 0x00 0x03480000 0x0 0x40000 /* lut registers */ - 0x00 0x034c0000 0x0 0x40000 /* pf controls registers */ - 0x80 0x00000000 0x0 0x20000>; /* configuration space */ - reg-names = "dbi", "lut", "ctrl", "config"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - num-lanes = <4>; - bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000 /* downstream I/O */ - 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ - }; - - pcie2: pcie@3500000 { - compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; - reg = <0x00 0x03500000 0x0 0x80000 - 0x00 0x03580000 0x0 0x40000 /* lut registers */ - 0x00 0x035c0000 0x0 0x40000 /* pf controls registers */ - 0x88 0x00000000 0x0 0x20000>; /* configuration space */ - reg-names = "dbi", "lut", "ctrl", "config"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - num-lanes = <4>; - bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000 /* downstream I/O */ - 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ - }; - pcie@1f0000000 { compatible = "pci-host-ecam-generic"; /* ECAM bus 0, HW has more space reserved but not populated */ @@ -484,5 +452,37 @@ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; + + pcie1: pcie@3400000 { + compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; + reg = <0x00 0x03400000 0x0 0x80000 + 0x00 0x03480000 0x0 0x40000 /* lut registers */ + 0x00 0x034c0000 0x0 0x40000 /* pf controls registers */ + 0x80 0x00000000 0x0 0x20000>; /* configuration space */ + reg-names = "dbi", "lut", "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + }; + + pcie2: pcie@3500000 { + compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; + reg = <0x00 0x03500000 0x0 0x80000 + 0x00 0x03580000 0x0 0x40000 /* lut registers */ + 0x00 0x035c0000 0x0 0x40000 /* pf controls registers */ + 0x88 0x00000000 0x0 0x20000>; /* configuration space */ + reg-names = "dbi", "lut", "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + }; }; };
While inserting it into the new location, keep it sorted by the register base offset just like in the linux kernel device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index d0f90941b9..c289009ca1 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -142,11 +142,6 @@ }; };
- cluster1_core0_watchdog: wdt@c000000 { - compatible = "arm,sp805-wdt"; - reg = <0x0 0xc000000 0x0 0x1000>; - }; - soc: soc { compatible = "simple-bus"; #address-cells = <2>; @@ -484,5 +479,10 @@ ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ }; + + cluster1_core0_watchdog: wdt@c000000 { + compatible = "arm,sp805-wdt"; + reg = <0x0 0xc000000 0x0 0x1000>; + }; }; };
While inserting them into the new location, keep them sorted by the register base offset just like in the linux kernel device tree.
While at it fix the indentation.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 202 +++++++++++++++++----------------- 1 file changed, 103 insertions(+), 99 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index c289009ca1..ca593c7218 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -43,105 +43,6 @@ IRQ_TYPE_LEVEL_LOW)>; };
- pcie@1f0000000 { - compatible = "pci-host-ecam-generic"; - /* ECAM bus 0, HW has more space reserved but not populated */ - bus-range = <0x0 0x0>; - reg = <0x01 0xf0000000 0x0 0x100000>; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges= <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>; - enetc0: pci@0,0 { - reg = <0x000000 0 0 0 0>; - status = "disabled"; - }; - enetc1: pci@0,1 { - reg = <0x000100 0 0 0 0>; - status = "disabled"; - }; - enetc2: pci@0,2 { - reg = <0x000200 0 0 0 0>; - status = "disabled"; - phy-mode = "internal"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - mdio0: pci@0,3 { - #address-cells=<0>; - #size-cells=<1>; - reg = <0x000300 0 0 0 0>; - status = "disabled"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - mscc_felix: pci@0,5 { - reg = <0x000500 0 0 0 0>; - status = "disabled"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - mscc_felix_port0: port@0 { - reg = <0>; - status = "disabled"; - }; - - mscc_felix_port1: port@1 { - reg = <1>; - status = "disabled"; - }; - - mscc_felix_port2: port@2 { - reg = <2>; - status = "disabled"; - }; - - mscc_felix_port3: port@3 { - reg = <3>; - status = "disabled"; - }; - - mscc_felix_port4: port@4 { - reg = <4>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - mscc_felix_port5: port@5 { - reg = <5>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - - }; - }; - }; - - enetc6: pci@0,6 { - reg = <0x000600 0 0 0 0>; - status = "disabled"; - phy-mode = "internal"; - }; - }; - soc: soc { compatible = "simple-bus"; #address-cells = <2>; @@ -484,5 +385,108 @@ compatible = "arm,sp805-wdt"; reg = <0x0 0xc000000 0x0 0x1000>; }; + + pcie@1f0000000 { + compatible = "pci-host-ecam-generic"; + /* ECAM bus 0, HW has more space reserved but not populated */ + bus-range = <0x0 0x0>; + reg = <0x01 0xf0000000 0x0 0x100000>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>; + + enetc0: pci@0,0 { + reg = <0x000000 0 0 0 0>; + status = "disabled"; + }; + + enetc1: pci@0,1 { + reg = <0x000100 0 0 0 0>; + status = "disabled"; + }; + + enetc2: pci@0,2 { + reg = <0x000200 0 0 0 0>; + status = "disabled"; + phy-mode = "internal"; + + fixed-link { + speed = <2500>; + full-duplex; + }; + }; + + mdio0: pci@0,3 { + #address-cells=<0>; + #size-cells=<1>; + reg = <0x000300 0 0 0 0>; + status = "disabled"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + mscc_felix: pci@0,5 { + reg = <0x000500 0 0 0 0>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mscc_felix_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + mscc_felix_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + mscc_felix_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + mscc_felix_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + mscc_felix_port4: port@4 { + reg = <4>; + phy-mode = "internal"; + status = "disabled"; + + fixed-link { + speed = <2500>; + full-duplex; + }; + }; + + mscc_felix_port5: port@5 { + reg = <5>; + phy-mode = "internal"; + status = "disabled"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + + }; + }; + }; + + enetc6: pci@0,6 { + reg = <0x000600 0 0 0 0>; + status = "disabled"; + phy-mode = "internal"; + }; + }; }; };
Update the labels of the nodes to match the kernel ones.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com Tested-by: Vladimir Oltean vladimir.oltean@nxp.com --- .../dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi | 10 +++---- .../fsl-ls1028a-kontron-sl28-var1-u-boot.dtsi | 2 +- .../arm/dts/fsl-ls1028a-kontron-sl28-var1.dts | 6 ++--- .../arm/dts/fsl-ls1028a-kontron-sl28-var2.dts | 8 +++--- .../fsl-ls1028a-kontron-sl28-var3-u-boot.dtsi | 2 +- .../fsl-ls1028a-kontron-sl28-var4-u-boot.dtsi | 4 +-- .../arm/dts/fsl-ls1028a-kontron-sl28-var4.dts | 4 +-- arch/arm/dts/fsl-ls1028a-kontron-sl28.dts | 22 ++++++++-------- .../dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi | 2 +- .../dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi | 2 +- .../dts/fsl-ls1028a-qds-7777-sch-30841.dtsi | 4 +-- .../dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi | 4 +-- .../dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi | 2 +- .../fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi | 4 +-- .../dts/fsl-ls1028a-qds-9999-sch-24801.dtsi | 4 +-- arch/arm/dts/fsl-ls1028a-qds-duart.dts | 2 +- .../fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi | 4 +-- .../fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi | 4 +-- .../dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi | 4 +-- .../dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi | 4 +-- arch/arm/dts/fsl-ls1028a-qds.dtsi | 16 ++++++------ arch/arm/dts/fsl-ls1028a-rdb.dts | 22 ++++++++-------- arch/arm/dts/fsl-ls1028a.dtsi | 26 +++++++++---------- 23 files changed, 81 insertions(+), 81 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi index fa4c05212a..42bd3138b2 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi @@ -5,13 +5,13 @@ / { aliases { mmc0 = &esdhc1; - mmc1 = &esdhc0; + mmc1 = &esdhc; i2c0 = &i2c0; i2c1 = &i2c3; i2c2 = &i2c4; rtc0 = &rtc; - ethernet2 = &enetc2; - ethernet3 = &enetc6; + ethernet2 = &enetc_port2; + ethernet3 = &enetc_port3; };
binman: binman { @@ -250,7 +250,7 @@ u-boot,dm-pre-reloc; };
-&esdhc0 { +&esdhc { u-boot,dm-pre-reloc; };
@@ -262,7 +262,7 @@ u-boot,dm-pre-reloc; };
-&serial0 { +&duart0 { u-boot,dm-pre-reloc; };
diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1-u-boot.dtsi index 98e8939369..a46e07dc6b 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1-u-boot.dtsi @@ -3,6 +3,6 @@
/ { aliases { - ethernet0 = &enetc1; + ethernet0 = &enetc_port1; }; }; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts index 33d85ed83a..ba2e4de96d 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts @@ -21,19 +21,19 @@ compatible = "kontron,sl28-var1", "kontron,sl28", "fsl,ls1028a"; };
-&enetc0 { +&enetc_port0 { status = "disabled"; /delete-property/ phy-handle; };
-&enetc1 { +&enetc_port1 { phy-handle = <&phy0>; phy-mode = "rgmii-id"; status = "okay"; };
/delete-node/ &phy0; -&mdio0 { +&enetc_mdio_pf3 { phy0: ethernet-phy@4 { reg = <0x4>; eee-broken-1000t; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts index 7a3aa21408..db80874f4e 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts @@ -17,12 +17,12 @@ compatible = "kontron,sl28-var2", "kontron,sl28", "fsl,ls1028a"; };
-&enetc0 { +&enetc_port0 { status = "disabled"; /delete-property/ phy-handle; };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -45,12 +45,12 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; };
/delete-node/ &phy0; -&mdio0 { +&enetc_mdio_pf3 { phy0: ethernet-phy@5 { reg = <0x5>; eee-broken-1000t; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var3-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var3-u-boot.dtsi index 879a76415b..3d6bf5a0bd 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var3-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var3-u-boot.dtsi @@ -3,6 +3,6 @@
/ { aliases { - ethernet0 = &enetc0; + ethernet0 = &enetc_port0; }; }; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4-u-boot.dtsi index fce4694682..5d82973bba 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4-u-boot.dtsi @@ -3,7 +3,7 @@
/ { aliases { - ethernet0 = &enetc0; - ethernet1 = &enetc1; + ethernet0 = &enetc_port0; + ethernet1 = &enetc_port1; }; }; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts index b95e082b70..54d12ab992 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts @@ -18,13 +18,13 @@ compatible = "kontron,sl28-var4", "kontron,sl28", "fsl,ls1028a"; };
-&enetc1 { +&enetc_port1 { phy-handle = <&phy1>; phy-mode = "rgmii-id"; status = "okay"; };
-&mdio0 { +&enetc_mdio_pf3 { phy1: ethernet-phy@4 { reg = <0x4>; eee-broken-1000t; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts index 7f237c39ec..9ae70ba541 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts @@ -14,8 +14,8 @@ compatible = "kontron,sl28", "fsl,ls1028a";
aliases { - serial0 = &serial0; - serial1 = &serial1; + serial0 = &duart0; + serial1 = &duart1; serial2 = &lpuart1; spi0 = &fspi; spi1 = &dspi2; @@ -30,21 +30,21 @@ status = "okay"; };
-&enetc0 { +&enetc_port0 { phy-handle = <&phy0>; phy-mode = "sgmii"; status = "okay"; };
-&enetc2 { +&enetc_port2 { status = "disabled"; };
-&enetc6 { +&enetc_port3 { status = "disabled"; };
-&esdhc0 { +&esdhc { sd-uhs-sdr104; sd-uhs-sdr50; sd-uhs-sdr25; @@ -108,7 +108,7 @@ status = "okay"; };
-&mdio0 { +&enetc_mdio_pf3 { status = "okay"; phy0: ethernet-phy@5 { reg = <0x5>; @@ -121,18 +121,18 @@ status = "okay"; };
-&serial0 { +&duart0 { status = "okay"; };
-&serial1 { +&duart1 { status = "okay"; };
-&usb1 { +&usb0 { status = "okay"; };
-&usb2 { +&usb1 { status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi index 1f13cf80e6..f4c557e69e 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi @@ -13,7 +13,7 @@ #include "fsl-sch-30842.dtsi" };
-&enetc0 { +&enetc_port0 { status = "okay"; phy-mode = "usxgmii"; phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; diff --git a/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi index 10375b2751..69274ee4e9 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-6xxx-sch-30842.dtsi @@ -12,7 +12,7 @@ #include "fsl-sch-30842.dtsi" };
-&enetc0 { +&enetc_port0 { status = "okay"; phy-mode = "2500base-x"; phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>; diff --git a/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi b/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi index f18cb39f21..90da665a3c 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-7777-sch-30841.dtsi @@ -20,7 +20,7 @@ #include "fsl-sch-30841.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -53,6 +53,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi b/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi index f6561a89eb..27c3d655bf 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-7xx7-sch-30841R.dtsi @@ -9,7 +9,7 @@ #include "fsl-sch-30841.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -30,6 +30,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi b/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi index d9ccd8353b..7d197c3181 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi @@ -12,7 +12,7 @@ #include "fsl-sch-24801.dtsi" };
-&enetc0 { +&enetc_port0 { status = "okay"; phy-mode = "sgmii"; phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>; diff --git a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi index 0630f12069..992092ec78 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi @@ -34,7 +34,7 @@ #include "fsl-sch-24801.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -67,6 +67,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi index 170aacf8c0..a905d77a9a 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi @@ -19,7 +19,7 @@ #include "fsl-sch-24801.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -52,6 +52,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-duart.dts b/arch/arm/dts/fsl-ls1028a-qds-duart.dts index 83264e0f54..81db21a947 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-duart.dts +++ b/arch/arm/dts/fsl-ls1028a-qds-duart.dts @@ -10,6 +10,6 @@
/ { chosen { - stdout-path = &serial0; + stdout-path = &duart0; }; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi index 1a9288a037..62e818f099 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi @@ -19,7 +19,7 @@ #include "fsl-sch-30841.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -52,6 +52,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi index 544f548b1a..6f1f6cb32a 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi @@ -13,7 +13,7 @@ #include "fsl-sch-28021.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -46,6 +46,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi index 639796263c..6c0d8b23ef 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-x7xx-sch-30842.dtsi @@ -9,7 +9,7 @@ #include "fsl-sch-30842.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -24,6 +24,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi index 62c5513c2c..9af6a5a674 100644 --- a/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds-xx7x-sch-30842.dtsi @@ -9,7 +9,7 @@ #include "fsl-sch-30842.dtsi" };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -24,6 +24,6 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds.dtsi b/arch/arm/dts/fsl-ls1028a-qds.dtsi index 335d7b1e4c..babd8445ee 100644 --- a/arch/arm/dts/fsl-ls1028a-qds.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds.dtsi @@ -105,7 +105,7 @@ }; };
-&esdhc0 { +&esdhc { status = "okay"; };
@@ -144,7 +144,7 @@ reg = <0x54>; #mux-control-cells = <1>; mux-reg-masks = <0x54 0xf0>; - mdio-parent-bus = <&mdio0>; + mdio-parent-bus = <&enetc_mdio_pf3>;
/* on-board MDIO with a single RGMII PHY */ mdio@00 { @@ -232,29 +232,29 @@ status = "okay"; };
-&serial0 { +&duart0 { status = "okay"; };
-&serial1 { +&duart1 { status = "okay"; };
-&usb1 { +&usb0 { status = "okay"; };
-&usb2 { +&usb1 { status = "okay"; };
-&enetc1 { +&enetc_port1 { status = "okay"; phy-mode = "rgmii-id"; phy-handle = <&qds_phy0>; };
-&mdio0 { +&enetc_mdio_pf3 { status = "okay"; };
diff --git a/arch/arm/dts/fsl-ls1028a-rdb.dts b/arch/arm/dts/fsl-ls1028a-rdb.dts index 708182f65c..18ee363d75 100644 --- a/arch/arm/dts/fsl-ls1028a-rdb.dts +++ b/arch/arm/dts/fsl-ls1028a-rdb.dts @@ -15,8 +15,8 @@ compatible = "fsl,ls1028a-rdb", "fsl,ls1028a"; aliases { spi0 = &fspi; - ethernet0 = &enetc0; - ethernet1 = &enetc2; + ethernet0 = &enetc_port0; + ethernet1 = &enetc_port2; ethernet2 = &mscc_felix_port0; ethernet3 = &mscc_felix_port1; ethernet4 = &mscc_felix_port2; @@ -36,7 +36,7 @@ status = "okay"; };
-&esdhc0 { +&esdhc { status = "okay"; };
@@ -114,29 +114,29 @@ status = "okay"; };
-&serial0 { +&duart0 { status = "okay"; };
-&serial1 { +&duart1 { status = "okay"; };
-&usb1 { +&usb0 { status = "okay"; };
-&usb2 { +&usb1 { status = "okay"; };
-&enetc0 { +&enetc_port0 { status = "okay"; phy-mode = "sgmii"; phy-handle = <&rdb_phy0>; };
-&enetc2 { +&enetc_port2 { status = "okay"; };
@@ -173,11 +173,11 @@ };
&mscc_felix_port4 { - ethernet = <&enetc2>; + ethernet = <&enetc_port2>; status = "okay"; };
-&mdio0 { +&enetc_mdio_pf3 { status = "okay"; rdb_phy0: phy@2 { reg = <2>; diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index ca593c7218..e5b5a0dc9f 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -196,7 +196,7 @@ status = "disabled"; };
- esdhc0: esdhc@2140000 { + esdhc: esdhc@2140000 { compatible = "fsl,esdhc"; reg = <0x0 0x2140000 0x0 0x10000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; @@ -215,7 +215,7 @@ status = "disabled"; };
- serial0: serial@21c0500 { + duart0: serial@21c0500 { device_type = "serial"; compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21c0500 0x0 0x100>; @@ -223,7 +223,7 @@ status = "disabled"; };
- serial1: serial@21c0600 { + duart1: serial@21c0600 { device_type = "serial"; compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21c0600 0x0 0x100>; @@ -291,7 +291,7 @@ status = "disabled"; };
- gpio0: gpio@2300000 { + gpio1: gpio@2300000 { compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2300000 0x0 0x10000>; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; @@ -302,7 +302,7 @@ little-endian; };
- gpio1: gpio@2310000 { + gpio2: gpio@2310000 { compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2310000 0x0 0x10000>; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; @@ -313,7 +313,7 @@ little-endian; };
- gpio2: gpio@2320000 { + gpio3: gpio@2320000 { compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2320000 0x0 0x10000>; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; @@ -324,7 +324,7 @@ little-endian; };
- usb1: usb3@3100000 { + usb0: usb3@3100000 { compatible = "fsl,layerscape-dwc3"; reg = <0x0 0x3100000 0x0 0x10000>; interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; @@ -332,7 +332,7 @@ status = "disabled"; };
- usb2: usb3@3110000 { + usb1: usb3@3110000 { compatible = "fsl,layerscape-dwc3"; reg = <0x0 0x3110000 0x0 0x10000>; interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; @@ -396,17 +396,17 @@ device_type = "pci"; ranges = <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>;
- enetc0: pci@0,0 { + enetc_port0: pci@0,0 { reg = <0x000000 0 0 0 0>; status = "disabled"; };
- enetc1: pci@0,1 { + enetc_port1: pci@0,1 { reg = <0x000100 0 0 0 0>; status = "disabled"; };
- enetc2: pci@0,2 { + enetc_port2: pci@0,2 { reg = <0x000200 0 0 0 0>; status = "disabled"; phy-mode = "internal"; @@ -417,7 +417,7 @@ }; };
- mdio0: pci@0,3 { + enetc_mdio_pf3: pci@0,3 { #address-cells=<0>; #size-cells=<1>; reg = <0x000300 0 0 0 0>; @@ -482,7 +482,7 @@ }; };
- enetc6: pci@0,6 { + enetc_port3: pci@0,6 { reg = <0x000600 0 0 0 0>; status = "disabled"; phy-mode = "internal";
According to the linux device tree specification the compatible string is: compatible = "arm,sp805", "arm,primecell";
Fix all users in u-boot.
Signed-off-by: Michael Walle michael@walle.cc --- arch/arm/dts/fsl-ls1028a.dtsi | 2 +- arch/arm/dts/hi3660.dtsi | 4 ++-- drivers/watchdog/sp805_wdt.c | 2 +- 3 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index e5b5a0dc9f..cbdddccaea 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -382,7 +382,7 @@ };
cluster1_core0_watchdog: wdt@c000000 { - compatible = "arm,sp805-wdt"; + compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc000000 0x0 0x1000>; };
diff --git a/arch/arm/dts/hi3660.dtsi b/arch/arm/dts/hi3660.dtsi index 65a45b0e80..028f4db60d 100644 --- a/arch/arm/dts/hi3660.dtsi +++ b/arch/arm/dts/hi3660.dtsi @@ -1087,7 +1087,7 @@ };
watchdog0: watchdog@e8a06000 { - compatible = "arm,sp805-wdt", "arm,primecell"; + compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xe8a06000 0x0 0x1000>; interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; clocks = <&crg_ctrl HI3660_OSC32K>; @@ -1095,7 +1095,7 @@ };
watchdog1: watchdog@e8a07000 { - compatible = "arm,sp805-wdt", "arm,primecell"; + compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xe8a07000 0x0 0x1000>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&crg_ctrl HI3660_OSC32K>; diff --git a/drivers/watchdog/sp805_wdt.c b/drivers/watchdog/sp805_wdt.c index bec8827ceb..0d6fb12065 100644 --- a/drivers/watchdog/sp805_wdt.c +++ b/drivers/watchdog/sp805_wdt.c @@ -134,7 +134,7 @@ static const struct wdt_ops sp805_wdt_ops = { };
static const struct udevice_id sp805_wdt_ids[] = { - { .compatible = "arm,sp805-wdt" }, + { .compatible = "arm,sp805" }, {} };
The official ls1028a binding of the driver uses the following as compatibles: compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
Add the missing compatible to the driver and update the device tree. We can use the fallback "fsl,ls1021a-v1.0-dspi", because the endianness is determined by the little-endian property and not by the compatible string itself. Further, we won't need and specific details on the DMA configuration (which is different on the LS1021A). If it's ever needed, we can later add the more specific "fsl,ls1028a-dspi" compatible to the driver.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 6 +++--- drivers/spi/fsl_dspi.c | 1 + 2 files changed, 4 insertions(+), 3 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index cbdddccaea..6158a1362a 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -158,7 +158,7 @@ };
dspi0: dspi@2100000 { - compatible = "fsl,vf610-dspi"; + compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2100000 0x0 0x10000>; @@ -171,7 +171,7 @@ };
dspi1: dspi@2110000 { - compatible = "fsl,vf610-dspi"; + compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2110000 0x0 0x10000>; @@ -184,7 +184,7 @@ };
dspi2: dspi@2120000 { - compatible = "fsl,vf610-dspi"; + compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2120000 0x0 0x10000>; diff --git a/drivers/spi/fsl_dspi.c b/drivers/spi/fsl_dspi.c index 8fe3508c64..23d812f476 100644 --- a/drivers/spi/fsl_dspi.c +++ b/drivers/spi/fsl_dspi.c @@ -654,6 +654,7 @@ static const struct dm_spi_ops fsl_dspi_ops = {
static const struct udevice_id fsl_dspi_ids[] = { { .compatible = "fsl,vf610-dspi" }, + { .compatible = "fsl,ls1021a-v1.0-dspi" }, { } };
The official devicetree bindings specifies spi-num-chipselects as the name. Use it.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1012a.dtsi | 2 +- arch/arm/dts/fsl-ls1028a.dtsi | 6 +++--- arch/arm/dts/fsl-ls1043a.dtsi | 4 ++-- arch/arm/dts/fsl-ls1046a.dtsi | 4 ++-- arch/arm/dts/fsl-ls1088a.dtsi | 2 +- arch/arm/dts/fsl-ls2080a.dtsi | 2 +- arch/arm/dts/fsl-lx2160a.dtsi | 6 +++--- arch/arm/dts/ls1021a.dtsi | 4 ++-- arch/arm/dts/vf.dtsi | 4 ++-- drivers/spi/fsl_dspi.c | 5 +++-- 10 files changed, 20 insertions(+), 19 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1012a.dtsi b/arch/arm/dts/fsl-ls1012a.dtsi index 2894842cf2..dcdcd444b3 100644 --- a/arch/arm/dts/fsl-ls1012a.dtsi +++ b/arch/arm/dts/fsl-ls1012a.dtsi @@ -49,7 +49,7 @@ interrupts = <0 64 0x4>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <6>; + spi-num-chipselects = <6>; big-endian; status = "disabled"; }; diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 6158a1362a..7da32561a4 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -165,7 +165,7 @@ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <5>; + spi-num-chipselects = <5>; litte-endian; status = "disabled"; }; @@ -178,7 +178,7 @@ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <5>; + spi-num-chipselects = <5>; little-endian; status = "disabled"; }; @@ -191,7 +191,7 @@ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <5>; + spi-num-chipselects = <5>; little-endian; status = "disabled"; }; diff --git a/arch/arm/dts/fsl-ls1043a.dtsi b/arch/arm/dts/fsl-ls1043a.dtsi index d8171bd03b..3aaec8b6af 100644 --- a/arch/arm/dts/fsl-ls1043a.dtsi +++ b/arch/arm/dts/fsl-ls1043a.dtsi @@ -53,7 +53,7 @@ interrupts = <0 64 0x4>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <6>; + spi-num-chipselects = <6>; big-endian; status = "disabled"; }; @@ -66,7 +66,7 @@ interrupts = <0 65 0x4>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <6>; + spi-num-chipselects = <6>; big-endian; status = "disabled"; }; diff --git a/arch/arm/dts/fsl-ls1046a.dtsi b/arch/arm/dts/fsl-ls1046a.dtsi index 9df419a87d..6a205cd3df 100644 --- a/arch/arm/dts/fsl-ls1046a.dtsi +++ b/arch/arm/dts/fsl-ls1046a.dtsi @@ -52,7 +52,7 @@ interrupts = <0 64 0x4>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <6>; + spi-num-chipselects = <6>; big-endian; status = "disabled"; }; @@ -65,7 +65,7 @@ interrupts = <0 65 0x4>; clock-names = "dspi"; clocks = <&clockgen 4 0>; - num-cs = <6>; + spi-num-chipselects = <6>; big-endian; status = "disabled"; }; diff --git a/arch/arm/dts/fsl-ls1088a.dtsi b/arch/arm/dts/fsl-ls1088a.dtsi index 3a5a50fb83..9e48a3ab94 100644 --- a/arch/arm/dts/fsl-ls1088a.dtsi +++ b/arch/arm/dts/fsl-ls1088a.dtsi @@ -89,7 +89,7 @@ #size-cells = <0>; reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <0 26 0x4>; /* Level high type */ - num-cs = <6>; + spi-num-chipselects = <6>; };
qspi: quadspi@1550000 { diff --git a/arch/arm/dts/fsl-ls2080a.dtsi b/arch/arm/dts/fsl-ls2080a.dtsi index 278daeeb6e..72ba52594a 100644 --- a/arch/arm/dts/fsl-ls2080a.dtsi +++ b/arch/arm/dts/fsl-ls2080a.dtsi @@ -93,7 +93,7 @@ #size-cells = <0>; reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <0 26 0x4>; /* Level high type */ - num-cs = <6>; + spi-num-chipselects = <6>; };
qspi: quadspi@1550000 { diff --git a/arch/arm/dts/fsl-lx2160a.dtsi b/arch/arm/dts/fsl-lx2160a.dtsi index 3b5f0d119e..52e4d7205a 100644 --- a/arch/arm/dts/fsl-lx2160a.dtsi +++ b/arch/arm/dts/fsl-lx2160a.dtsi @@ -172,7 +172,7 @@ #size-cells = <0>; reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <0 26 0x4>; /* Level high type */ - num-cs = <6>; + spi-num-chipselects = <6>; };
dspi1: dspi@2110000 { @@ -181,7 +181,7 @@ #size-cells = <0>; reg = <0x0 0x2110000 0x0 0x10000>; interrupts = <0 26 0x4>; /* Level high type */ - num-cs = <6>; + spi-num-chipselects = <6>; };
dspi2: dspi@2120000 { @@ -190,7 +190,7 @@ #size-cells = <0>; reg = <0x0 0x2120000 0x0 0x10000>; interrupts = <0 241 0x4>; /* Level high type */ - num-cs = <6>; + spi-num-chipselects = <6>; };
gpio0: gpio@2300000 { diff --git a/arch/arm/dts/ls1021a.dtsi b/arch/arm/dts/ls1021a.dtsi index 7ba2dd2269..8aefc82f87 100644 --- a/arch/arm/dts/ls1021a.dtsi +++ b/arch/arm/dts/ls1021a.dtsi @@ -190,7 +190,7 @@ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&platform_clk 1>; - num-cs = <6>; + spi-num-chipselects = <6>; big-endian; status = "disabled"; }; @@ -203,7 +203,7 @@ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; clocks = <&platform_clk 1>; - num-cs = <6>; + spi-num-chipselects = <6>; big-endian; status = "disabled"; }; diff --git a/arch/arm/dts/vf.dtsi b/arch/arm/dts/vf.dtsi index 5f69d0fd6e..0d512d111e 100644 --- a/arch/arm/dts/vf.dtsi +++ b/arch/arm/dts/vf.dtsi @@ -70,7 +70,7 @@ #size-cells = <0>; compatible = "fsl,vf610-dspi"; reg = <0x4002c000 0x1000>; - num-cs = <5>; + spi-num-chipselects = <5>; status = "disabled"; };
@@ -79,7 +79,7 @@ #size-cells = <0>; compatible = "fsl,vf610-dspi"; reg = <0x4002d000 0x1000>; - num-cs = <5>; + spi-num-chipselects = <5>; status = "disabled"; };
diff --git a/drivers/spi/fsl_dspi.c b/drivers/spi/fsl_dspi.c index 23d812f476..62444e408a 100644 --- a/drivers/spi/fsl_dspi.c +++ b/drivers/spi/fsl_dspi.c @@ -586,8 +586,9 @@ static int fsl_dspi_of_to_plat(struct udevice *bus) if (fdtdec_get_bool(blob, node, "big-endian")) plat->flags |= DSPI_FLAG_REGMAP_ENDIAN_BIG;
- plat->num_chipselect = - fdtdec_get_int(blob, node, "num-cs", FSL_DSPI_MAX_CHIPSELECT); + plat->num_chipselect = fdtdec_get_int(blob, node, + "spi-num-chipselects", + FSL_DSPI_MAX_CHIPSELECT);
addr = dev_read_addr(bus); if (addr == FDT_ADDR_T_NONE) {
The official ls1028a binding of the driver uses the following as compatibles: compatible = "fsl,ls1028a-lpuart";
Add the missing compatible to the driver and update the device tree.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 18 ++++++------------ drivers/serial/serial_lpuart.c | 2 ++ 2 files changed, 8 insertions(+), 12 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 7da32561a4..cf381a0856 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -232,62 +232,56 @@ };
lpuart0: serial@2260000 { - compatible = "fsl,ls1021a-lpuart"; + compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2260000 0x0 0x1000>; interrupts = <0 232 0x4>; clocks = <&sysclk>; clock-names = "ipg"; - little-endian; status = "disabled"; };
lpuart1: serial@2270000 { - compatible = "fsl,ls1021a-lpuart"; + compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2270000 0x0 0x1000>; interrupts = <0 233 0x4>; clocks = <&sysclk>; clock-names = "ipg"; - little-endian; status = "disabled"; };
lpuart2: serial@2280000 { - compatible = "fsl,ls1021a-lpuart"; + compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2280000 0x0 0x1000>; interrupts = <0 234 0x4>; clocks = <&sysclk>; clock-names = "ipg"; - little-endian; status = "disabled"; };
lpuart3: serial@2290000 { - compatible = "fsl,ls1021a-lpuart"; + compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2290000 0x0 0x1000>; interrupts = <0 235 0x4>; clocks = <&sysclk>; clock-names = "ipg"; - little-endian; status = "disabled"; };
lpuart4: serial@22a0000 { - compatible = "fsl,ls1021a-lpuart"; + compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22a0000 0x0 0x1000>; interrupts = <0 236 0x4>; clocks = <&sysclk>; clock-names = "ipg"; - little-endian; status = "disabled"; };
lpuart5: serial@22b0000 { - compatible = "fsl,ls1021a-lpuart"; + compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22b0000 0x0 0x1000>; interrupts = <0 237 0x4>; clocks = <&sysclk>; clock-names = "ipg"; - little-endian; status = "disabled"; };
diff --git a/drivers/serial/serial_lpuart.c b/drivers/serial/serial_lpuart.c index 2b473d70f6..3c9a69598a 100644 --- a/drivers/serial/serial_lpuart.c +++ b/drivers/serial/serial_lpuart.c @@ -553,6 +553,8 @@ static const struct dm_serial_ops lpuart_serial_ops = { static const struct udevice_id lpuart_serial_ids[] = { { .compatible = "fsl,ls1021a-lpuart", .data = LPUART_FLAG_REGMAP_32BIT_REG | LPUART_FLAG_REGMAP_ENDIAN_BIG }, + { .compatible = "fsl,ls1028a-lpuart", + .data = LPUART_FLAG_REGMAP_32BIT_REG }, { .compatible = "fsl,imx7ulp-lpuart", .data = LPUART_FLAG_REGMAP_32BIT_REG }, { .compatible = "fsl,vf610-lpuart"},
The driver will look for a named resource "ecc-addr", but this isn't the official binding. In fact, the official device tree binding documentation doesn't mention any resource names at all. But it is safe to assume that it's the linux ones we have to use if we want to be compatible with the linux device tree. Thus rename "ecc-addr" to "sata-ecc" and convert all the users in u-boot.
While at it, also rename "sata-base" to "ahci" although its not used at all.
This change doesn't affect the SATA controller on the ZynqMP.
Cc: Michal Simek monstr@monstr.eu Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1012a.dtsi | 2 +- arch/arm/dts/fsl-ls1028a.dtsi | 2 +- arch/arm/dts/fsl-ls1043a.dtsi | 2 +- arch/arm/dts/fsl-ls1046a.dtsi | 2 +- arch/arm/dts/fsl-ls1088a.dtsi | 2 +- arch/arm/dts/ls1021a.dtsi | 2 +- drivers/ata/sata_ceva.c | 2 +- 7 files changed, 7 insertions(+), 7 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1012a.dtsi b/arch/arm/dts/fsl-ls1012a.dtsi index dcdcd444b3..0ea899c7d7 100644 --- a/arch/arm/dts/fsl-ls1012a.dtsi +++ b/arch/arm/dts/fsl-ls1012a.dtsi @@ -157,7 +157,7 @@ compatible = "fsl,ls1012a-ahci"; reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ 0x0 0x20140520 0x0 0x4>; /* ecc sata addr */ - reg-names = "sata-base", "ecc-addr"; + reg-names = "ahci", "sata-ecc"; interrupts = <0 69 4>; clocks = <&clockgen 4 0>; status = "disabled"; diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index cf381a0856..34aad526fe 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -338,7 +338,7 @@ compatible = "fsl,ls1028a-ahci"; reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ 0x7 0x100520 0x0 0x4>; /* ecc sata addr*/ - reg-names = "sata-base", "ecc-addr"; + reg-names = "ahci", "sata-ecc"; interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; diff --git a/arch/arm/dts/fsl-ls1043a.dtsi b/arch/arm/dts/fsl-ls1043a.dtsi index 3aaec8b6af..52dc5a9638 100644 --- a/arch/arm/dts/fsl-ls1043a.dtsi +++ b/arch/arm/dts/fsl-ls1043a.dtsi @@ -331,7 +331,7 @@ compatible = "fsl,ls1043a-ahci"; reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ 0x0 0x20140520 0x0 0x4>; /* ecc sata addr*/ - reg-names = "sata-base", "ecc-addr"; + reg-names = "ahci", "sata-ecc"; interrupts = <0 69 4>; clocks = <&clockgen 4 0>; status = "disabled"; diff --git a/arch/arm/dts/fsl-ls1046a.dtsi b/arch/arm/dts/fsl-ls1046a.dtsi index 6a205cd3df..a60cbf11fc 100644 --- a/arch/arm/dts/fsl-ls1046a.dtsi +++ b/arch/arm/dts/fsl-ls1046a.dtsi @@ -367,7 +367,7 @@ compatible = "fsl,ls1046a-ahci"; reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ 0x0 0x20140520 0x0 0x4>; /* ecc sata addr*/ - reg-names = "sata-base", "ecc-addr"; + reg-names = "ahci", "sata-ecc"; interrupts = <0 69 4>; clocks = <&clockgen 4 1>; status = "disabled"; diff --git a/arch/arm/dts/fsl-ls1088a.dtsi b/arch/arm/dts/fsl-ls1088a.dtsi index 9e48a3ab94..ee0e3b367d 100644 --- a/arch/arm/dts/fsl-ls1088a.dtsi +++ b/arch/arm/dts/fsl-ls1088a.dtsi @@ -226,7 +226,7 @@ compatible = "fsl,ls1088a-ahci"; reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ 0x7 0x100520 0x0 0x4>; /* ecc sata addr*/ - reg-names = "sata-base", "ecc-addr"; + reg-names = "ahci", "sata-ecc"; interrupts = <0 133 4>; status = "disabled"; }; diff --git a/arch/arm/dts/ls1021a.dtsi b/arch/arm/dts/ls1021a.dtsi index 8aefc82f87..86192cbb7f 100644 --- a/arch/arm/dts/ls1021a.dtsi +++ b/arch/arm/dts/ls1021a.dtsi @@ -469,7 +469,7 @@ sata: sata@3200000 { compatible = "fsl,ls1021a-ahci"; reg = <0x3200000 0x10000 0x20220520 0x4>; - reg-names = "sata-base", "ecc-addr"; + reg-names = "ahci", "sata-ecc"; interrupts = <0 101 4>; status = "disabled"; }; diff --git a/drivers/ata/sata_ceva.c b/drivers/ata/sata_ceva.c index 87e6a90f74..b71f10223d 100644 --- a/drivers/ata/sata_ceva.c +++ b/drivers/ata/sata_ceva.c @@ -212,7 +212,7 @@ static int sata_ceva_of_to_plat(struct udevice *dev) if (priv->base == FDT_ADDR_T_NONE) return -EINVAL;
- ret = dev_read_resource_byname(dev, "ecc-addr", &res_regs); + ret = dev_read_resource_byname(dev, "sata-ecc", &res_regs); if (ret) priv->ecc_base = 0; else
The official ls1028a binding of the driver uses the following as compatibles: compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
Change the ls1028a device tree and add this new compatible to the fsl specific xhci driver, otherwise the generic dwc3 driver will be used with the compatibles above.
Cc: Bin Meng bmeng.cn@gmail.com Cc: Marek Vasut marex@denx.de Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Bin Meng bmeng.cn@gmail.com --- arch/arm/dts/fsl-ls1028a.dtsi | 4 ++-- drivers/usb/host/xhci-fsl.c | 1 + 2 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 34aad526fe..cc055e65e5 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -319,7 +319,7 @@ };
usb0: usb3@3100000 { - compatible = "fsl,layerscape-dwc3"; + compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; reg = <0x0 0x3100000 0x0 0x10000>; interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "host"; @@ -327,7 +327,7 @@ };
usb1: usb3@3110000 { - compatible = "fsl,layerscape-dwc3"; + compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; reg = <0x0 0x3110000 0x0 0x10000>; interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "host"; diff --git a/drivers/usb/host/xhci-fsl.c b/drivers/usb/host/xhci-fsl.c index f062f12ade..80871908dc 100644 --- a/drivers/usb/host/xhci-fsl.c +++ b/drivers/usb/host/xhci-fsl.c @@ -159,6 +159,7 @@ static int xhci_fsl_remove(struct udevice *dev)
static const struct udevice_id xhci_usb_ids[] = { { .compatible = "fsl,layerscape-dwc3", }, + { .compatible = "fsl,ls1028a-dwc3", }, { } };
The official bindind of the PCIe controller of the ls1028a has the following compatible string: compatible = "fsl,ls1028a-pcie";
Additionally, the resource names and count are different. Update the driver to support this binding and change the entry in the ls1028a device tree.
Cc: Hou Zhiqiang Zhiqiang.Hou@nxp.com Signed-off-by: Michael Walle michael@walle.cc --- arch/arm/dts/fsl-ls1028a.dtsi | 20 +++++------ drivers/pci/pcie_layerscape_rc.c | 61 +++++++++++++++++++++++--------- 2 files changed, 53 insertions(+), 28 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index cc055e65e5..435b965d00 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -344,12 +344,10 @@ };
pcie1: pcie@3400000 { - compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; - reg = <0x00 0x03400000 0x0 0x80000 - 0x00 0x03480000 0x0 0x40000 /* lut registers */ - 0x00 0x034c0000 0x0 0x40000 /* pf controls registers */ - 0x80 0x00000000 0x0 0x20000>; /* configuration space */ - reg-names = "dbi", "lut", "ctrl", "config"; + compatible = "fsl,ls1028a-pcie"; + reg = <0x00 0x03400000 0x0 0x00100000>, /* controller registers */ + <0x80 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; @@ -360,12 +358,10 @@ };
pcie2: pcie@3500000 { - compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie"; - reg = <0x00 0x03500000 0x0 0x80000 - 0x00 0x03580000 0x0 0x40000 /* lut registers */ - 0x00 0x035c0000 0x0 0x40000 /* pf controls registers */ - 0x88 0x00000000 0x0 0x20000>; /* configuration space */ - reg-names = "dbi", "lut", "ctrl", "config"; + compatible = "fsl,ls1028a-pcie"; + reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers */ + <0x88 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; diff --git a/drivers/pci/pcie_layerscape_rc.c b/drivers/pci/pcie_layerscape_rc.c index f50d6ef653..217b420076 100644 --- a/drivers/pci/pcie_layerscape_rc.c +++ b/drivers/pci/pcie_layerscape_rc.c @@ -21,6 +21,12 @@
DECLARE_GLOBAL_DATA_PTR;
+struct ls_pcie_drvdata { + u32 lut_offset; + u32 ctrl_offset; + bool big_endian; +}; + static void ls_pcie_cfg0_set_busdev(struct ls_pcie_rc *pcie_rc, u32 busdev) { struct ls_pcie *pcie = pcie_rc->pcie; @@ -243,6 +249,7 @@ static void ls_pcie_setup_ctrl(struct ls_pcie_rc *pcie_rc)
static int ls_pcie_probe(struct udevice *dev) { + const struct ls_pcie_drvdata *drvdata = (void *)dev_get_driver_data(dev); struct ls_pcie_rc *pcie_rc = dev_get_priv(dev); const void *fdt = gd->fdt_blob; int node = dev_of_offset(dev); @@ -260,8 +267,12 @@ static int ls_pcie_probe(struct udevice *dev)
pcie_rc->pcie = pcie;
+ /* try resource name of the official binding first */ ret = fdt_get_named_resource(fdt, node, "reg", "reg-names", - "dbi", &pcie_rc->dbi_res); + "regs", &pcie_rc->dbi_res); + if (ret) + ret = fdt_get_named_resource(fdt, node, "reg", "reg-names", + "dbi", &pcie_rc->dbi_res); if (ret) { printf("ls-pcie: resource "dbi" not found\n"); return ret; @@ -287,21 +298,29 @@ static int ls_pcie_probe(struct udevice *dev) if (pcie->mode == PCI_HEADER_TYPE_NORMAL) return 0;
- ret = fdt_get_named_resource(fdt, node, "reg", "reg-names", - "lut", &pcie_rc->lut_res); - if (!ret) - pcie->lut = map_physmem(pcie_rc->lut_res.start, - fdt_resource_size(&pcie_rc->lut_res), - MAP_NOCACHE); + if (drvdata) { + pcie->lut = pcie->dbi + drvdata->lut_offset; + } else { + ret = fdt_get_named_resource(fdt, node, "reg", "reg-names", + "lut", &pcie_rc->lut_res); + if (!ret) + pcie->lut = map_physmem(pcie_rc->lut_res.start, + fdt_resource_size(&pcie_rc->lut_res), + MAP_NOCACHE); + }
- ret = fdt_get_named_resource(fdt, node, "reg", "reg-names", - "ctrl", &pcie_rc->ctrl_res); - if (!ret) - pcie->ctrl = map_physmem(pcie_rc->ctrl_res.start, - fdt_resource_size(&pcie_rc->ctrl_res), - MAP_NOCACHE); - if (!pcie->ctrl) - pcie->ctrl = pcie->lut; + if (drvdata) { + pcie->ctrl = pcie->lut + drvdata->ctrl_offset; + } else { + ret = fdt_get_named_resource(fdt, node, "reg", "reg-names", + "ctrl", &pcie_rc->ctrl_res); + if (!ret) + pcie->ctrl = map_physmem(pcie_rc->ctrl_res.start, + fdt_resource_size(&pcie_rc->ctrl_res), + MAP_NOCACHE); + if (!pcie->ctrl) + pcie->ctrl = pcie->lut; + }
if (!pcie->ctrl) { printf("%s: NOT find CTRL\n", dev->name); @@ -343,7 +362,10 @@ static int ls_pcie_probe(struct udevice *dev) pcie_rc->cfg1 = pcie_rc->cfg0 + fdt_resource_size(&pcie_rc->cfg_res) / 2;
- pcie->big_endian = fdtdec_get_bool(fdt, node, "big-endian"); + if (drvdata) + pcie->big_endian = drvdata->big_endian; + else + pcie->big_endian = fdtdec_get_bool(fdt, node, "big-endian");
debug("%s dbi:%lx lut:%lx ctrl:0x%lx cfg0:0x%lx, big-endian:%d\n", dev->name, (unsigned long)pcie->dbi, (unsigned long)pcie->lut, @@ -373,8 +395,15 @@ static const struct dm_pci_ops ls_pcie_ops = { .write_config = ls_pcie_write_config, };
+static const struct ls_pcie_drvdata ls1028a_drvdata = { + .lut_offset = 0x80000, + .ctrl_offset = 0x40000, + .big_endian = false, +}; + static const struct udevice_id ls_pcie_ids[] = { { .compatible = "fsl,ls-pcie" }, + { .compatible = "fsl,ls1028a-pcie", .data = (ulong)&ls1028a_drvdata }, { } };
-----Original Message----- From: Michael Walle [mailto:michael@walle.cc] Sent: 2021年10月14日 0:14 To: u-boot@lists.denx.de Cc: Jagan Teki jagan@amarulasolutions.com; Priyanka Jain priyanka.jain@nxp.com; Vladimir Oltean vladimir.oltean@nxp.com; Tom Rini trini@konsulko.com; Peter Griffin peter.griffin@linaro.org; Manivannan Sadhasivam manivannan.sadhasivam@linaro.org; Michael Walle michael@walle.cc; Z.Q. Hou zhiqiang.hou@nxp.com Subject: [PATCH v5 23/28] pci: layerscape: add official ls1028a binding support
The official bindind of the PCIe controller of the ls1028a has the following compatible string: compatible = "fsl,ls1028a-pcie";
Additionally, the resource names and count are different. Update the driver to support this binding and change the entry in the ls1028a device tree.
Cc: Hou Zhiqiang Zhiqiang.Hou@nxp.com Signed-off-by: Michael Walle michael@walle.cc
arch/arm/dts/fsl-ls1028a.dtsi | 20 +++++------ drivers/pci/pcie_layerscape_rc.c | 61 +++++++++++++++++++++++--------- 2 files changed, 53 insertions(+), 28 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index cc055e65e5..435b965d00 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -344,12 +344,10 @@ };
pcie1: pcie@3400000 {
compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";reg = <0x00 0x03400000 0x0 0x800000x00 0x03480000 0x0 0x40000 /* lut registers */0x00 0x034c0000 0x0 0x40000 /* pf controls registers*/
0x80 0x00000000 0x0 0x20000>; /* configuration space*/
reg-names = "dbi", "lut", "ctrl", "config";
compatible = "fsl,ls1028a-pcie";reg = <0x00 0x03400000 0x0 0x00100000>, /* controller registers*/
<0x80 0x00000000 0x0 0x00002000>; /* configurationspace */
reg-names = "regs", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci";@@ -360,12 +358,10 @@ };
pcie2: pcie@3500000 {
compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";reg = <0x00 0x03500000 0x0 0x800000x00 0x03580000 0x0 0x40000 /* lut registers */0x00 0x035c0000 0x0 0x40000 /* pf controls registers*/
0x88 0x00000000 0x0 0x20000>; /* configuration space*/
reg-names = "dbi", "lut", "ctrl", "config";
compatible = "fsl,ls1028a-pcie";reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers*/
<0x88 0x00000000 0x0 0x00002000>; /* configurationspace */
reg-names = "regs", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci";diff --git a/drivers/pci/pcie_layerscape_rc.c b/drivers/pci/pcie_layerscape_rc.c index f50d6ef653..217b420076 100644 --- a/drivers/pci/pcie_layerscape_rc.c +++ b/drivers/pci/pcie_layerscape_rc.c @@ -21,6 +21,12 @@
DECLARE_GLOBAL_DATA_PTR;
+struct ls_pcie_drvdata {
- u32 lut_offset;
- u32 ctrl_offset;
- bool big_endian;
+};
static void ls_pcie_cfg0_set_busdev(struct ls_pcie_rc *pcie_rc, u32 busdev) { struct ls_pcie *pcie = pcie_rc->pcie; @@ -243,6 +249,7 @@ static void ls_pcie_setup_ctrl(struct ls_pcie_rc *pcie_rc)
static int ls_pcie_probe(struct udevice *dev) {
- const struct ls_pcie_drvdata *drvdata = (void
+*)dev_get_driver_data(dev); struct ls_pcie_rc *pcie_rc = dev_get_priv(dev); const void *fdt = gd->fdt_blob; int node = dev_of_offset(dev); @@ -260,8 +267,12 @@ static int ls_pcie_probe(struct udevice *dev)
pcie_rc->pcie = pcie;
- /* try resource name of the official binding first */ ret = fdt_get_named_resource(fdt, node, "reg", "reg-names",
"dbi", &pcie_rc->dbi_res);
"regs", &pcie_rc->dbi_res);- if (ret)
ret = fdt_get_named_resource(fdt, node, "reg", "reg-names","dbi", &pcie_rc->dbi_res);@@ -287,21 +298,29 @@ static int ls_pcie_probe(struct udevice *dev) if (pcie->mode == PCI_HEADER_TYPE_NORMAL) return 0;
- ret = fdt_get_named_resource(fdt, node, "reg", "reg-names",
"lut", &pcie_rc->lut_res);- if (!ret)
pcie->lut = map_physmem(pcie_rc->lut_res.start,fdt_resource_size(&pcie_rc->lut_res),MAP_NOCACHE);
- if (drvdata) {
pcie->lut = pcie->dbi + drvdata->lut_offset;- } else {
ret = fdt_get_named_resource(fdt, node, "reg", "reg-names","lut", &pcie_rc->lut_res);if (!ret)pcie->lut = map_physmem(pcie_rc->lut_res.start,fdt_resource_size(&pcie_rc->lut_res),MAP_NOCACHE);- }
- ret = fdt_get_named_resource(fdt, node, "reg", "reg-names",
"ctrl", &pcie_rc->ctrl_res);- if (!ret)
pcie->ctrl = map_physmem(pcie_rc->ctrl_res.start,fdt_resource_size(&pcie_rc->ctrl_res),MAP_NOCACHE);- if (!pcie->ctrl)
pcie->ctrl = pcie->lut;
if (drvdata) {
pcie->ctrl = pcie->lut + drvdata->ctrl_offset;} else {
ret = fdt_get_named_resource(fdt, node, "reg", "reg-names","ctrl", &pcie_rc->ctrl_res);if (!ret)pcie->ctrl = map_physmem(pcie_rc->ctrl_res.start,fdt_resource_size(&pcie_rc->ctrl_res),MAP_NOCACHE);if (!pcie->ctrl)pcie->ctrl = pcie->lut;}
if (!pcie->ctrl) { printf("%s: NOT find CTRL\n", dev->name); @@ -343,7 +362,10 @@
static int ls_pcie_probe(struct udevice *dev) pcie_rc->cfg1 = pcie_rc->cfg0 + fdt_resource_size(&pcie_rc->cfg_res) / 2;
- pcie->big_endian = fdtdec_get_bool(fdt, node, "big-endian");
if (drvdata)
pcie->big_endian = drvdata->big_endian;else
pcie->big_endian = fdtdec_get_bool(fdt, node, "big-endian");debug("%s dbi:%lx lut:%lx ctrl:0x%lx cfg0:0x%lx, big-endian:%d\n", dev->name, (unsigned long)pcie->dbi, (unsigned long)pcie->lut, @@
-373,8 +395,15 @@ static const struct dm_pci_ops ls_pcie_ops = { .write_config = ls_pcie_write_config, };
+static const struct ls_pcie_drvdata ls1028a_drvdata = {
- .lut_offset = 0x80000,
- .ctrl_offset = 0x40000,
- .big_endian = false,
+};
static const struct udevice_id ls_pcie_ids[] = { { .compatible = "fsl,ls-pcie" },
- { .compatible = "fsl,ls1028a-pcie", .data = (ulong)&ls1028a_drvdata }, { }
};
-- 2.30.2
Reviewed-by: Hou Zhiqiang Zhiqiang.Hou@nxp.com
This property is unused in the layerscape PCIe controller driver and not present in the linux device tree. Remove it to be similarly.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 2 -- 1 file changed, 2 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 435b965d00..3ef710bb3d 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -351,7 +351,6 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ @@ -365,7 +364,6 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
To make the synchronization of the u-boot device tree with the one from linux easier, move the I/O window to the one which is specified in the linux device tree. The actual value shouldn't matter as long as it mapped to the corresponding memory window of the PCIe controller which is a 32GiB window at 80_0000_0000h (first controller) or 88_0000_0000h (second controller).
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Hou Zhiqiang Zhiqiang.Hou@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index 3ef710bb3d..f11e75032b 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -352,7 +352,7 @@ #size-cells = <2>; device_type = "pci"; bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000 /* downstream I/O */ + ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ };
@@ -365,7 +365,7 @@ #size-cells = <2>; device_type = "pci"; bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000 /* downstream I/O */ + ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ };
Disable the PCIe controllers by default, just like in the linux device tree. But there is one catch, for linux they are enabled in-place by the bootloader. Obviously, this doesn't work for the bootloader. Thus we explicitly enable the controllers in the -u-boot.dtsi files.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi | 13 +++++++++++++ arch/arm/dts/fsl-ls1028a-qds.dtsi | 8 ++++++++ arch/arm/dts/fsl-ls1028a-rdb.dts | 8 ++++++++ arch/arm/dts/fsl-ls1028a.dtsi | 2 ++ 4 files changed, 31 insertions(+)
diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi index 42bd3138b2..25aa274765 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi @@ -266,6 +266,19 @@ u-boot,dm-pre-reloc; };
+/* + * u-boot will enable the device in the linux device tree in place. Because + * we are using the linux device tree, we have to enable the PCI controller + * ourselves. + */ +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + &soc { u-boot,dm-pre-reloc; }; diff --git a/arch/arm/dts/fsl-ls1028a-qds.dtsi b/arch/arm/dts/fsl-ls1028a-qds.dtsi index babd8445ee..0da0a7bc5d 100644 --- a/arch/arm/dts/fsl-ls1028a-qds.dtsi +++ b/arch/arm/dts/fsl-ls1028a-qds.dtsi @@ -240,6 +240,14 @@ status = "okay"; };
+&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + &usb0 { status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a-rdb.dts b/arch/arm/dts/fsl-ls1028a-rdb.dts index 18ee363d75..537ebbc697 100644 --- a/arch/arm/dts/fsl-ls1028a-rdb.dts +++ b/arch/arm/dts/fsl-ls1028a-rdb.dts @@ -122,6 +122,14 @@ status = "okay"; };
+&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + &usb0 { status = "okay"; }; diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index f11e75032b..d2f558d208 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -354,6 +354,7 @@ bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + status = "disabled"; };
pcie2: pcie@3500000 { @@ -367,6 +368,7 @@ bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + status = "disabled"; };
cluster1_core0_watchdog: wdt@c000000 {
Now that everything is prepared, copy the fsl-ls1028a.dtsi from the linux kernel v5.14.12.
Notable changes: - second watchdog added - the number of chip selects of the SPI controller is now correct and reflects what the hardware offers - the LPUARTs have the correct clock parent - USB controllers are enabled by default, which was already the case before this sync because all board enabled all the USB controller nodes. A linux patch to fix this is pending. - the eSDHC controller changes from big-endian to little-endian, but that property seems to be not used at all.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- arch/arm/dts/fsl-ls1028a.dtsi | 860 ++++++++++++++++-- .../dt-bindings/clock/fsl,qoriq-clockgen.h | 15 + 2 files changed, 785 insertions(+), 90 deletions(-) create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.h
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi index d2f558d208..06b36cc658 100644 --- a/arch/arm/dts/fsl-ls1028a.dtsi +++ b/arch/arm/dts/fsl-ls1028a.dtsi @@ -1,12 +1,16 @@ -// SPDX-License-Identifier: GPL-2.0+ OR X11 +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* - * NXP ls1028a SOC common device tree source + * Device Tree Include file for NXP Layerscape-1028A family SoC. * - * Copyright 2019-2020 NXP + * Copyright 2018-2020 NXP + * + * Harninder Rai harninder.rai@nxp.com * */
+#include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/thermal/thermal.h>
/ { compatible = "fsl,ls1028a"; @@ -14,6 +18,54 @@ #address-cells = <2>; #size-cells = <2>;
+ cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x0>; + enable-method = "psci"; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; + next-level-cache = <&l2>; + cpu-idle-states = <&CPU_PW20>; + #cooling-cells = <2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x1>; + enable-method = "psci"; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; + next-level-cache = <&l2>; + cpu-idle-states = <&CPU_PW20>; + #cooling-cells = <2>; + }; + + l2: l2-cache { + compatible = "cache"; + }; + }; + + idle-states { + /* + * PSCI node is not added default, U-boot will add missing + * parts if it determines to use PSCI. + */ + entry-method = "psci"; + + CPU_PW20: cpu-pw20 { + compatible = "arm,idle-state"; + idle-state-name = "PW20"; + arm,psci-suspend-param = <0x0>; + entry-latency-us = <2000>; + exit-latency-us = <2000>; + min-residency-us = <6000>; + }; + }; + sysclk: sysclk { compatible = "fixed-clock"; #clock-cells = <0>; @@ -21,14 +73,33 @@ clock-output-names = "sysclk"; };
- gic: interrupt-controller@6000000 { - compatible = "arm,gic-v3"; - reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ - <0x0 0x06040000 0 0x40000>; - #interrupt-cells = <3>; - interrupt-controller; - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) | - IRQ_TYPE_LEVEL_LOW)>; + osc_27m: clock-osc-27m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + clock-output-names = "phy_27m"; + }; + + dpclk: clock-controller@f1f0000 { + compatible = "fsl,ls1028a-plldig"; + reg = <0x0 0xf1f0000 0x0 0xffff>; + #clock-cells = <0>; + clocks = <&osc_27m>; + }; + + firmware { + optee: optee { + compatible = "linaro,optee-tz"; + method = "smc"; + status = "disabled"; + }; + }; + + reboot { + compatible ="syscon-reboot"; + regmap = <&rst>; + offset = <0>; + mask = <0x02>; };
timer { @@ -43,13 +114,123 @@ IRQ_TYPE_LEVEL_LOW)>; };
+ pmu { + compatible = "arm,cortex-a72-pmu"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + gic: interrupt-controller@6000000 { + compatible= "arm,gic-v3"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + reg= <0x0 0x06000000 0 0x10000>, /* GIC Dist */ + <0x0 0x06040000 0 0x40000>; /* GIC Redistributor */ + #interrupt-cells= <3>; + interrupt-controller; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) | + IRQ_TYPE_LEVEL_LOW)>; + its: gic-its@6020000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x06020000 0 0x20000>;/* GIC Translater */ + }; + }; + + thermal-zones { + ddr-controller { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 0>; + + trips { + ddr-ctrler-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + ddr-ctrler-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + core-cluster { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 1>; + + trips { + core_cluster_alert: core-cluster-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core_cluster_crit: core-cluster-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster_alert>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + soc: soc { compatible = "simple-bus"; #address-cells = <2>; #size-cells = <2>; ranges;
- clockgen: clocking@1300000 { + ddr: memory-controller@1080000 { + compatible = "fsl,qoriq-memory-controller"; + reg = <0x0 0x1080000 0x0 0x1000>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + little-endian; + }; + + dcfg: syscon@1e00000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,ls1028a-dcfg", "syscon", "simple-mfd"; + reg = <0x0 0x1e00000 0x0 0x10000>; + ranges = <0x0 0x0 0x1e00000 0x10000>; + little-endian; + + fspi_clk: clock-controller@900 { + compatible = "fsl,ls1028a-flexspi-clk"; + reg = <0x900 0x4>; + #clock-cells = <0>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 0>; + clock-output-names = "fspi_clk"; + }; + }; + + rst: syscon@1e60000 { + compatible = "syscon"; + reg = <0x0 0x1e60000 0x0 0x10000>; + little-endian; + }; + + scfg: syscon@1fc0000 { + compatible = "fsl,ls1028a-scfg", "syscon"; + reg = <0x0 0x1fc0000 0x0 0x10000>; + big-endian; + }; + + clockgen: clock-controller@1300000 { compatible = "fsl,ls1028a-clockgen"; reg = <0x0 0x1300000 0x0 0xa0000>; #clock-cells = <2>; @@ -62,8 +243,8 @@ #size-cells = <0>; reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -73,8 +254,8 @@ #size-cells = <0>; reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -84,8 +265,8 @@ #size-cells = <0>; reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -95,8 +276,8 @@ #size-cells = <0>; reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -106,8 +287,8 @@ #size-cells = <0>; reg = <0x0 0x2040000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -117,8 +298,8 @@ #size-cells = <0>; reg = <0x0 0x2050000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -128,8 +309,8 @@ #size-cells = <0>; reg = <0x0 0x2060000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -139,152 +320,237 @@ #size-cells = <0>; reg = <0x0 0x2070000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
- fspi: flexspi@20c0000 { + fspi: spi@20c0000 { compatible = "nxp,lx2160a-fspi"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x20c0000 0x0 0x10000>, <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "fspi_en", "fspi"; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&fspi_clk>, <&fspi_clk>; + clock-names = "fspi_en", "fspi"; status = "disabled"; };
- dspi0: dspi@2100000 { + dspi0: spi@2100000 { compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 0>; - spi-num-chipselects = <5>; - litte-endian; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + dmas = <&edma0 0 62>, <&edma0 0 60>; + dma-names = "tx", "rx"; + spi-num-chipselects = <4>; + little-endian; status = "disabled"; };
- dspi1: dspi@2110000 { + dspi1: spi@2110000 { compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2110000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 0>; - spi-num-chipselects = <5>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + dmas = <&edma0 0 58>, <&edma0 0 56>; + dma-names = "tx", "rx"; + spi-num-chipselects = <4>; little-endian; status = "disabled"; };
- dspi2: dspi@2120000 { + dspi2: spi@2120000 { compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2120000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 0>; - spi-num-chipselects = <5>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + dmas = <&edma0 0 54>, <&edma0 0 2>; + dma-names = "tx", "rx"; + spi-num-chipselects = <3>; little-endian; status = "disabled"; };
- esdhc: esdhc@2140000 { - compatible = "fsl,esdhc"; + esdhc: mmc@2140000 { + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc"; reg = <0x0 0x2140000 0x0 0x10000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - big-endian; + clock-frequency = <0>; /* fixed up by bootloader */ + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + little-endian; bus-width = <4>; status = "disabled"; };
- esdhc1: esdhc@2150000 { - compatible = "fsl,esdhc"; + esdhc1: mmc@2150000 { + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc"; reg = <0x0 0x2150000 0x0 0x10000>; interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; - big-endian; + clock-frequency = <0>; /* fixed up by bootloader */ + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; + voltage-ranges = <1800 1800>; + sdhci,auto-cmd12; non-removable; + little-endian; bus-width = <4>; status = "disabled"; };
+ can0: can@2180000 { + compatible = "fsl,lx2160ar1-flexcan"; + reg = <0x0 0x2180000 0x0 0x10000>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + can1: can@2190000 { + compatible = "fsl,lx2160ar1-flexcan"; + reg = <0x0 0x2190000 0x0 0x10000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + duart0: serial@21c0500 { - device_type = "serial"; compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0500 0x0 0x100>; + reg = <0x00 0x21c0500 0x0 0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };
duart1: serial@21c0600 { - device_type = "serial"; compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0600 0x0 0x100>; + reg = <0x00 0x21c0600 0x0 0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };
+ lpuart0: serial@2260000 { compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2260000 0x0 0x1000>; - interrupts = <0 232 0x4>; - clocks = <&sysclk>; + interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 32>, + <&edma0 1 33>; status = "disabled"; };
lpuart1: serial@2270000 { compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2270000 0x0 0x1000>; - interrupts = <0 233 0x4>; - clocks = <&sysclk>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 30>, + <&edma0 1 31>; status = "disabled"; };
lpuart2: serial@2280000 { compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2280000 0x0 0x1000>; - interrupts = <0 234 0x4>; - clocks = <&sysclk>; + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 28>, + <&edma0 1 29>; status = "disabled"; };
lpuart3: serial@2290000 { compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2290000 0x0 0x1000>; - interrupts = <0 235 0x4>; - clocks = <&sysclk>; + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 26>, + <&edma0 1 27>; status = "disabled"; };
lpuart4: serial@22a0000 { compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22a0000 0x0 0x1000>; - interrupts = <0 236 0x4>; - clocks = <&sysclk>; + interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 24>, + <&edma0 1 25>; status = "disabled"; };
lpuart5: serial@22b0000 { compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22b0000 0x0 0x1000>; - interrupts = <0 237 0x4>; - clocks = <&sysclk>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; + dma-names = "rx","tx"; + dmas = <&edma0 1 22>, + <&edma0 1 23>; status = "disabled"; };
+ edma0: dma-controller@22c0000 { + #dma-cells = <2>; + compatible = "fsl,ls1028a-edma", "fsl,vf610-edma"; + reg = <0x0 0x22c0000 0x0 0x10000>, + <0x0 0x22d0000 0x0 0x10000>, + <0x0 0x22e0000 0x0 0x10000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; + dma-channels = <32>; + clock-names = "dmamux0", "dmamux1"; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + }; + gpio1: gpio@2300000 { compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2300000 0x0 0x10000>; @@ -318,28 +584,34 @@ little-endian; };
- usb0: usb3@3100000 { + usb0: usb@3100000 { compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; reg = <0x0 0x3100000 0x0 0x10000>; interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "host"; - status = "disabled"; + snps,dis_rxdet_inp3_quirk; + snps,quirk-frame-length-adjustment = <0x20>; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; };
- usb1: usb3@3110000 { + usb1: usb@3110000 { compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; reg = <0x0 0x3110000 0x0 0x10000>; interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "host"; - status = "disabled"; + snps,dis_rxdet_inp3_quirk; + snps,quirk-frame-length-adjustment = <0x20>; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; };
sata: sata@3200000 { compatible = "fsl,ls1028a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */ - 0x7 0x100520 0x0 0x4>; /* ecc sata addr*/ + reg = <0x0 0x3200000 0x0 0x10000>, + <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };
@@ -348,12 +620,25 @@ reg = <0x00 0x03400000 0x0 0x00100000>, /* controller registers */ <0x80 0x00000000 0x0 0x00002000>; /* configuration space */ reg-names = "regs", "config"; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */ + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; /* aer interrupt */ + interrupt-names = "pme", "aer"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; + num-viewport = <8>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */ status = "disabled"; };
@@ -362,44 +647,380 @@ reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers */ <0x88 0x00000000 0x0 0x00002000>; /* configuration space */ reg-names = "regs", "config"; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pme", "aer"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; + num-viewport = <8>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 2 &gic 0 0 GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 3 &gic 0 0 GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 4 &gic 0 0 GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */ status = "disabled"; };
- cluster1_core0_watchdog: wdt@c000000 { + smmu: iommu@5000000 { + compatible = "arm,mmu-500"; + reg = <0 0x5000000 0 0x800000>; + #global-interrupts = <8>; + #iommu-cells = <1>; + stream-match-mask = <0x7c00>; + /* global secure fault */ + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + /* combined secure interrupt */ + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + /* global non-secure fault */ + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + /* combined non-secure interrupt */ + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + /* performance counter interrupts 0-7 */ + <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>, + /* per context interrupt, 64 interrupts */ + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + }; + + crypto: crypto@8000000 { + compatible = "fsl,sec-v5.0", "fsl,sec-v4.0"; + fsl,sec-era = <10>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0x8000000 0x100000>; + reg = <0x00 0x8000000 0x0 0x100000>; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; + dma-coherent; + + sec_jr0: jr@10000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x10000 0x10000>; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr1: jr@20000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x20000 0x10000>; + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr2: jr@30000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x30000 0x10000>; + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr3: jr@40000 { + compatible = "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x40000 0x10000>; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + qdma: dma-controller@8380000 { + compatible = "fsl,ls1028a-qdma", "fsl,ls1021a-qdma"; + reg = <0x0 0x8380000 0x0 0x1000>, /* Controller regs */ + <0x0 0x8390000 0x0 0x10000>, /* Status regs */ + <0x0 0x83a0000 0x0 0x40000>; /* Block regs */ + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "qdma-error", "qdma-queue0", + "qdma-queue1", "qdma-queue2", "qdma-queue3"; + dma-channels = <8>; + block-number = <1>; + block-offset = <0x10000>; + fsl,dma-queues = <2>; + status-sizes = <64>; + queue-sizes = <64 64>; + }; + + cluster1_core0_watchdog: watchdog@c000000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc000000 0x0 0x1000>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; + clock-names = "wdog_clk", "apb_pclk"; + }; + + cluster1_core1_watchdog: watchdog@c010000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x0 0xc010000 0x0 0x1000>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; + clock-names = "wdog_clk", "apb_pclk"; + }; + + sai1: audio-controller@f100000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf100000 0x0 0x10000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 4>, + <&edma0 1 3>; + fsl,sai-asynchronous; + status = "disabled"; + }; + + sai2: audio-controller@f110000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf110000 0x0 0x10000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 6>, + <&edma0 1 5>; + fsl,sai-asynchronous; + status = "disabled"; + }; + + sai3: audio-controller@f120000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf120000 0x0 0x10000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 8>, + <&edma0 1 7>; + fsl,sai-asynchronous; + status = "disabled"; + }; + + sai4: audio-controller@f130000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf130000 0x0 0x10000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 10>, + <&edma0 1 9>; + fsl,sai-asynchronous; + status = "disabled"; + }; + + sai5: audio-controller@f140000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf140000 0x0 0x10000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 12>, + <&edma0 1 11>; + fsl,sai-asynchronous; + status = "disabled"; + }; + + sai6: audio-controller@f150000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf150000 0x0 0x10000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 14>, + <&edma0 1 13>; + fsl,sai-asynchronous; + status = "disabled"; };
- pcie@1f0000000 { + tmu: tmu@1f80000 { + compatible = "fsl,qoriq-tmu"; + reg = <0x0 0x1f80000 0x0 0x10000>; + interrupts = <0 23 0x4>; + fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>; + fsl,tmu-calibration = <0x00000000 0x00000024 + 0x00000001 0x0000002b + 0x00000002 0x00000031 + 0x00000003 0x00000038 + 0x00000004 0x0000003f + 0x00000005 0x00000045 + 0x00000006 0x0000004c + 0x00000007 0x00000053 + 0x00000008 0x00000059 + 0x00000009 0x00000060 + 0x0000000a 0x00000066 + 0x0000000b 0x0000006d + + 0x00010000 0x0000001c + 0x00010001 0x00000024 + 0x00010002 0x0000002c + 0x00010003 0x00000035 + 0x00010004 0x0000003d + 0x00010005 0x00000045 + 0x00010006 0x0000004d + 0x00010007 0x00000055 + 0x00010008 0x0000005e + 0x00010009 0x00000066 + 0x0001000a 0x0000006e + + 0x00020000 0x00000018 + 0x00020001 0x00000022 + 0x00020002 0x0000002d + 0x00020003 0x00000038 + 0x00020004 0x00000043 + 0x00020005 0x0000004d + 0x00020006 0x00000058 + 0x00020007 0x00000063 + 0x00020008 0x0000006e + + 0x00030000 0x00000010 + 0x00030001 0x0000001c + 0x00030002 0x00000029 + 0x00030003 0x00000036 + 0x00030004 0x00000042 + 0x00030005 0x0000004f + 0x00030006 0x0000005b + 0x00030007 0x00000068>; + little-endian; + #thermal-sensor-cells = <1>; + }; + + pcie@1f0000000 { /* Integrated Endpoint Root Complex */ compatible = "pci-host-ecam-generic"; - /* ECAM bus 0, HW has more space reserved but not populated */ - bus-range = <0x0 0x0>; reg = <0x01 0xf0000000 0x0 0x100000>; #address-cells = <3>; #size-cells = <2>; + msi-parent = <&its>; device_type = "pci"; - ranges = <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>; + bus-range = <0x0 0x0>; + dma-coherent; + msi-map = <0 &its 0x17 0xe>; + iommu-map = <0 &smmu 0x17 0xe>; + /* PF0-6 BAR0 - non-prefetchable memory */ + ranges = <0x82000000 0x1 0xf8000000 0x1 0xf8000000 0x0 0x160000 + /* PF0-6 BAR2 - prefetchable memory */ + 0xc2000000 0x1 0xf8160000 0x1 0xf8160000 0x0 0x070000 + /* PF0: VF0-1 BAR0 - non-prefetchable memory */ + 0x82000000 0x1 0xf81d0000 0x1 0xf81d0000 0x0 0x020000 + /* PF0: VF0-1 BAR2 - prefetchable memory */ + 0xc2000000 0x1 0xf81f0000 0x1 0xf81f0000 0x0 0x020000 + /* PF1: VF0-1 BAR0 - non-prefetchable memory */ + 0x82000000 0x1 0xf8210000 0x1 0xf8210000 0x0 0x020000 + /* PF1: VF0-1 BAR2 - prefetchable memory */ + 0xc2000000 0x1 0xf8230000 0x1 0xf8230000 0x0 0x020000 + /* BAR4 (PF5) - non-prefetchable memory */ + 0x82000000 0x1 0xfc000000 0x1 0xfc000000 0x0 0x400000>;
- enetc_port0: pci@0,0 { + enetc_port0: ethernet@0,0 { + compatible = "fsl,enetc"; reg = <0x000000 0 0 0 0>; status = "disabled"; };
- enetc_port1: pci@0,1 { + enetc_port1: ethernet@0,1 { + compatible = "fsl,enetc"; reg = <0x000100 0 0 0 0>; status = "disabled"; };
- enetc_port2: pci@0,2 { + enetc_port2: ethernet@0,2 { + compatible = "fsl,enetc"; reg = <0x000200 0 0 0 0>; - status = "disabled"; phy-mode = "internal"; + status = "disabled";
fixed-link { speed = <2500>; @@ -407,26 +1028,32 @@ }; };
- enetc_mdio_pf3: pci@0,3 { - #address-cells=<0>; - #size-cells=<1>; + enetc_mdio_pf3: mdio@0,3 { + compatible = "fsl,enetc-mdio"; reg = <0x000300 0 0 0 0>; - status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + };
- fixed-link { - speed = <1000>; - full-duplex; - }; + ethernet@0,4 { + compatible = "fsl,enetc-ptp"; + reg = <0x000400 0 0 0 0>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 3>; + little-endian; + fsl,extts-fifo; };
- mscc_felix: pci@0,5 { + mscc_felix: ethernet-switch@0,5 { reg = <0x000500 0 0 0 0>; + /* IEP INT_B */ + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; status = "disabled";
ports { #address-cells = <1>; #size-cells = <0>;
+ /* External ports */ mscc_felix_port0: port@0 { reg = <0>; status = "disabled"; @@ -447,6 +1074,7 @@ status = "disabled"; };
+ /* Internal ports */ mscc_felix_port4: port@4 { reg = <4>; phy-mode = "internal"; @@ -467,15 +1095,67 @@ speed = <1000>; full-duplex; }; - }; }; };
- enetc_port3: pci@0,6 { + enetc_port3: ethernet@0,6 { + compatible = "fsl,enetc"; reg = <0x000600 0 0 0 0>; - status = "disabled"; phy-mode = "internal"; + status = "disabled"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + rcec@1f,0 { + reg = <0x00f800 0 0 0 0>; + /* IEP INT_A */ + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + /* Integrated Endpoint Register Block */ + ierb@1f0800000 { + compatible = "fsl,ls1028a-enetc-ierb"; + reg = <0x01 0xf0800000 0x0 0x10000>; + }; + + rcpm: power-controller@1e34040 { + compatible = "fsl,ls1028a-rcpm", "fsl,qoriq-rcpm-2.1+"; + reg = <0x0 0x1e34040 0x0 0x1c>; + #fsl,rcpm-wakeup-cells = <7>; + little-endian; + }; + + ftm_alarm0: timer@2800000 { + compatible = "fsl,ls1028a-ftm-alarm"; + reg = <0x0 0x2800000 0x0 0x10000>; + fsl,rcpm-wakeup = <&rcpm 0x0 0x0 0x0 0x0 0x4000 0x0 0x0>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + malidp0: display@f080000 { + compatible = "arm,mali-dp500"; + reg = <0x0 0xf080000 0x0 0x10000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 223 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "DE", "SE"; + clocks = <&dpclk>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>; + clock-names = "pxlclk", "mclk", "aclk", "pclk"; + arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; + arm,malidp-arqos-value = <0xd000d000>; + + port { + dp0_out: endpoint { + }; }; }; diff --git a/include/dt-bindings/clock/fsl,qoriq-clockgen.h b/include/dt-bindings/clock/fsl,qoriq-clockgen.h new file mode 100644 index 0000000000..ddec7d0bdc --- /dev/null +++ b/include/dt-bindings/clock/fsl,qoriq-clockgen.h @@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#ifndef DT_CLOCK_FSL_QORIQ_CLOCKGEN_H +#define DT_CLOCK_FSL_QORIQ_CLOCKGEN_H + +#define QORIQ_CLK_SYSCLK 0 +#define QORIQ_CLK_CMUX 1 +#define QORIQ_CLK_HWACCEL 2 +#define QORIQ_CLK_FMAN 3 +#define QORIQ_CLK_PLATFORM_PLL 4 +#define QORIQ_CLK_CORECLK 5 + +#define QORIQ_CLK_PLL_DIV(x) ((x) - 1) + +#endif /* DT_CLOCK_FSL_QORIQ_CLOCKGEN_H */
Copy the board device tree files from linux v5.14. On top of the v5.14 dtbs the changes of these two patches are included here which are needed for u-boot: https://lore.kernel.org/linux-devicetree/20210831134013.1625527-7-michael@wa... https://lore.kernel.org/linux-devicetree/20210831134013.1625527-8-michael@wa...
At the time of this writing the patches were accepted and will be included in 5.15.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com --- .../dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi | 12 +- .../arm/dts/fsl-ls1028a-kontron-sl28-var1.dts | 31 +-- .../fsl-ls1028a-kontron-sl28-var2-u-boot.dtsi | 8 + .../arm/dts/fsl-ls1028a-kontron-sl28-var2.dts | 40 +-- .../arm/dts/fsl-ls1028a-kontron-sl28-var4.dts | 16 +- arch/arm/dts/fsl-ls1028a-kontron-sl28.dts | 250 +++++++++++++++--- 6 files changed, 265 insertions(+), 92 deletions(-)
diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi index 25aa274765..8538ce7984 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi @@ -4,12 +4,9 @@
/ { aliases { - mmc0 = &esdhc1; - mmc1 = &esdhc; i2c0 = &i2c0; i2c1 = &i2c3; i2c2 = &i2c4; - rtc0 = &rtc; ethernet2 = &enetc_port2; ethernet3 = &enetc_port3; }; @@ -234,11 +231,6 @@ }; #endif
-&i2c0 { - rtc: rtc@32 { - }; -}; - &fspi { u-boot,dm-pre-reloc; flash@0 { @@ -279,6 +271,10 @@ status = "okay"; };
+&sata { + status = "okay"; +}; + &soc { u-boot,dm-pre-reloc; }; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts index ba2e4de96d..7cd29ab970 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var1.dts @@ -8,7 +8,7 @@ * None of the four SerDes lanes are used by the module, instead they are * all led out to the carrier for customer use. * - * Copyright (C) 2020 Michael Walle michael@walle.cc + * Copyright (C) 2021 Michael Walle michael@walle.cc * */
@@ -21,28 +21,17 @@ compatible = "kontron,sl28-var1", "kontron,sl28", "fsl,ls1028a"; };
-&enetc_port0 { - status = "disabled"; - /delete-property/ phy-handle; -}; - -&enetc_port1 { - phy-handle = <&phy0>; - phy-mode = "rgmii-id"; - status = "okay"; -}; - -/delete-node/ &phy0; &enetc_mdio_pf3 { + /* Delete unused phy node */ + /delete-node/ ethernet-phy@5; + phy0: ethernet-phy@4 { reg = <0x4>; eee-broken-1000t; eee-broken-100tx; - qca,clk-out-frequency = <125000000>; qca,clk-out-strength = <AR803X_STRENGTH_FULL>; qca,keep-pll-enabled; - vddio-supply = <&vddio>;
vddio: vddio-regulator { @@ -56,3 +45,15 @@ }; }; }; + +&enetc_port0 { + status = "disabled"; + /* Delete the phy-handle to the old phy0 label */ + /delete-property/ phy-handle; +}; + +&enetc_port1 { + phy-handle = <&phy0>; + phy-mode = "rgmii-id"; + status = "okay"; +}; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2-u-boot.dtsi index 4e0ce3f77d..c010ea0dc7 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2-u-boot.dtsi +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2-u-boot.dtsi @@ -7,3 +7,11 @@ ethernet1 = &mscc_felix_port1; }; }; + +&mscc_felix_port0 { + label = "gbe0"; +}; + +&mscc_felix_port1 { + label = "gbe1"; +}; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts index db80874f4e..330e34f933 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var2.dts @@ -2,10 +2,10 @@ /* * Device Tree file for the Kontron SMARC-sAL28 board. * - * This is for the network variant 2 which has no ethernet support in the - * bootloader. + * This is for the network variant 2 which has two ethernet ports. These + * ports are connected to the internal switch. * - * Copyright (C) 2020 Michael Walle michael@walle.cc + * Copyright (C) 2021 Michael Walle michael@walle.cc * */
@@ -17,8 +17,21 @@ compatible = "kontron,sl28-var2", "kontron,sl28", "fsl,ls1028a"; };
+&enetc_mdio_pf3 { + phy1: ethernet-phy@4 { + reg = <0x4>; + eee-broken-1000t; + eee-broken-100tx; + }; +}; + &enetc_port0 { status = "disabled"; + /* + * In the base device tree the PHY at address 5 was assigned for + * this port. On this module this PHY is connected to a switch + * port instead. Therefore, delete the phy-handle property here. + */ /delete-property/ phy-handle; };
@@ -31,14 +44,16 @@ };
&mscc_felix_port0 { - label = "gbe0"; + label = "swp0"; + managed = "in-band-status"; phy-handle = <&phy0>; phy-mode = "sgmii"; status = "okay"; };
&mscc_felix_port1 { - label = "gbe1"; + label = "swp1"; + managed = "in-band-status"; phy-handle = <&phy1>; phy-mode = "sgmii"; status = "okay"; @@ -48,18 +63,3 @@ ethernet = <&enetc_port2>; status = "okay"; }; - -/delete-node/ &phy0; -&enetc_mdio_pf3 { - phy0: ethernet-phy@5 { - reg = <0x5>; - eee-broken-1000t; - eee-broken-100tx; - }; - - phy1: ethernet-phy@4 { - reg = <0x4>; - eee-broken-1000t; - eee-broken-100tx; - }; -}; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts index 54d12ab992..9b5e92fb75 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-var4.dts @@ -5,7 +5,7 @@ * This is for the network variant 4 which has two ethernet ports. It * extends the base and provides one more port connected via RGMII. * - * Copyright (C) 2019 Michael Walle michael@walle.cc + * Copyright (C) 2021 Michael Walle michael@walle.cc * */
@@ -18,22 +18,14 @@ compatible = "kontron,sl28-var4", "kontron,sl28", "fsl,ls1028a"; };
-&enetc_port1 { - phy-handle = <&phy1>; - phy-mode = "rgmii-id"; - status = "okay"; -}; - &enetc_mdio_pf3 { phy1: ethernet-phy@4 { reg = <0x4>; eee-broken-1000t; eee-broken-100tx; - qca,clk-out-frequency = <125000000>; qca,clk-out-strength = <AR803X_STRENGTH_FULL>; qca,keep-pll-enabled; - vddio-supply = <&vddio>;
vddio: vddio-regulator { @@ -47,3 +39,9 @@ }; }; }; + +&enetc_port1 { + phy-handle = <&phy1>; + phy-mode = "rgmii-id"; + status = "okay"; +}; diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts b/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts index 9ae70ba541..ab713b4949 100644 --- a/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts +++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28.dts @@ -2,23 +2,61 @@ /* * Device Tree file for the Kontron SMARC-sAL28 board. * - * Copyright (C) 2019 Michael Walle michael@walle.cc + * Copyright (C) 2021 Michael Walle michael@walle.cc * */
/dts-v1/; #include "fsl-ls1028a.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h>
/ { model = "Kontron SMARC-sAL28"; compatible = "kontron,sl28", "fsl,ls1028a";
aliases { + crypto = &crypto; serial0 = &duart0; serial1 = &duart1; serial2 = &lpuart1; spi0 = &fspi; spi1 = &dspi2; + mmc0 = &esdhc1; + mmc1 = &esdhc; + rtc0 = &rtc; + rtc1 = &ftm_alarm0; + }; + + buttons0 { + compatible = "gpio-keys"; + + power-button { + interrupts-extended = <&sl28cpld_intc + 4 IRQ_TYPE_EDGE_BOTH>; + linux,code = <KEY_POWER>; + label = "Power"; + }; + + sleep-button { + interrupts-extended = <&sl28cpld_intc + 5 IRQ_TYPE_EDGE_BOTH>; + linux,code = <KEY_SLEEP>; + label = "Sleep"; + }; + }; + + buttons1 { + compatible = "gpio-keys-polled"; + poll-interval = <200>; + + lid-switch { + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + gpios = <&sl28cpld_gpio3 4 GPIO_ACTIVE_LOW>; + label = "Lid"; + }; };
chosen { @@ -26,22 +64,35 @@ }; };
+&can0 { + status = "okay"; +}; + &dspi2 { status = "okay"; };
-&enetc_port0 { - phy-handle = <&phy0>; - phy-mode = "sgmii"; +&duart0 { + status = "okay"; +}; + +&duart1 { status = "okay"; };
-&enetc_port2 { - status = "disabled"; +&enetc_mdio_pf3 { + phy0: ethernet-phy@5 { + reg = <0x5>; + eee-broken-1000t; + eee-broken-100tx; + }; };
-&enetc_port3 { - status = "disabled"; +&enetc_port0 { + phy-handle = <&phy0>; + phy-mode = "sgmii"; + managed = "in-band-status"; + status = "okay"; };
&esdhc { @@ -63,8 +114,6 @@ status = "okay";
flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "jedec,spi-nor"; m25p,fast-read; spi-max-frequency = <133000000>; @@ -72,17 +121,167 @@ /* The following setting enables 1-1-2 (CMD-ADDR-DATA) mode */ spi-rx-bus-width = <2>; /* 2 SPI Rx lines */ spi-tx-bus-width = <1>; /* 1 SPI Tx line */ + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x000000 0x010000>; + label = "rcw"; + read-only; + }; + + partition@10000 { + reg = <0x010000 0x1d0000>; + label = "failsafe bootloader"; + read-only; + }; + + partition@200000 { + reg = <0x200000 0x010000>; + label = "configuration store"; + }; + + partition@210000 { + reg = <0x210000 0x1d0000>; + label = "bootloader"; + }; + + partition@3e0000 { + reg = <0x3e0000 0x020000>; + label = "bootloader environment"; + }; + }; }; };
+&gpio1 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "TDO", "TCK", + "", "", "", "", "", "", "", ""; +}; + +&gpio2 { + gpio-line-names = + "", "", "", "", "", "", "TMS", "TDI", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + &i2c0 { status = "okay";
- rtc@32 { + rtc: rtc@32 { compatible = "microcrystal,rv8803"; reg = <0x32>; };
+ sl28cpld@4a { + compatible = "kontron,sl28cpld"; + reg = <0x4a>; + #address-cells = <1>; + #size-cells = <0>; + + watchdog@4 { + compatible = "kontron,sl28cpld-wdt"; + reg = <0x4>; + kontron,assert-wdt-timeout-pin; + }; + + hwmon@b { + compatible = "kontron,sl28cpld-fan"; + reg = <0xb>; + }; + + sl28cpld_pwm0: pwm@c { + compatible = "kontron,sl28cpld-pwm"; + reg = <0xc>; + #pwm-cells = <2>; + }; + + sl28cpld_pwm1: pwm@e { + compatible = "kontron,sl28cpld-pwm"; + reg = <0xe>; + #pwm-cells = <2>; + }; + + sl28cpld_gpio0: gpio@10 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x10>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "GPIO0_CAM0_PWR_N", "GPIO1_CAM1_PWR_N", + "GPIO2_CAM0_RST_N", "GPIO3_CAM1_RST_N", + "GPIO4_HDA_RST_N", "GPIO5_PWM_OUT", + "GPIO6_TACHIN", "GPIO7"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sl28cpld_gpio1: gpio@15 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x15>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "GPIO8", "GPIO9", "GPIO10", "GPIO11", + "", "", "", ""; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sl28cpld_gpio2: gpio@1a { + compatible = "kontron,sl28cpld-gpo"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "LCD0 voltage enable", + "LCD0 backlight enable", + "eMMC reset", "LVDS bridge reset", + "LVDS bridge power-down", + "SDIO power enable", + "", ""; + }; + + sl28cpld_gpio3: gpio@1b { + compatible = "kontron,sl28cpld-gpi"; + reg = <0x1b>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "Power button", "Force recovery", "Sleep", + "Battery low", "Lid state", "Charging", + "Charger present", ""; + }; + + sl28cpld_intc: interrupt-controller@1c { + compatible = "kontron,sl28cpld-intc"; + reg = <0x1c>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + eeprom@50 { compatible = "atmel,24c32"; reg = <0x50>; @@ -107,32 +306,3 @@ &lpuart1 { status = "okay"; }; - -&enetc_mdio_pf3 { - status = "okay"; - phy0: ethernet-phy@5 { - reg = <0x5>; - eee-broken-1000t; - eee-broken-100tx; - }; -}; - -&sata { - status = "okay"; -}; - -&duart0 { - status = "okay"; -}; - -&duart1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; - -&usb1 { - status = "okay"; -};
Am 2021-10-13 18:14, schrieb Michael Walle:
Copy the board device tree files from linux v5.14. On top of the v5.14 dtbs the changes of these two patches are included here which are needed for u-boot:
https://lore.kernel.org/linux-devicetree/20210831134013.1625527-7-michael@wa...
https://lore.kernel.org/linux-devicetree/20210831134013.1625527-8-michael@wa...
At the time of this writing the patches were accepted and will be included in 5.15.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com
Ping.
I have some more patches which depends on this. TBH this is really frustrating if you have to wait serveral months until you can continue development.
-michael
On Wed, Nov 10, 2021 at 09:47:30AM +0100, Michael Walle wrote:
Am 2021-10-13 18:14, schrieb Michael Walle:
Copy the board device tree files from linux v5.14. On top of the v5.14 dtbs the changes of these two patches are included here which are needed for u-boot:
https://lore.kernel.org/linux-devicetree/20210831134013.1625527-7-michael@wa...
https://lore.kernel.org/linux-devicetree/20210831134013.1625527-8-michael@wa...
At the time of this writing the patches were accepted and will be included in 5.15.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com
Ping.
I have some more patches which depends on this. TBH this is really frustrating if you have to wait serveral months until you can continue development.
I want to chime in and say that I am also unhappy with how long it is taking to get these patches merged, as they fix some rather grievous errors that should not have been introduced to start with. These must come in for this release ASAP.
-----Original Message----- From: U-Boot u-boot-bounces@lists.denx.de On Behalf Of Tom Rini Sent: Thursday, November 11, 2021 3:03 AM To: Michael Walle michael@walle.cc; Priyanka Jain priyanka.jain@nxp.com Cc: u-boot@lists.denx.de; Jagan Teki jagan@amarulasolutions.com; Vladimir Oltean vladimir.oltean@nxp.com; Peter Griffin peter.griffin@linaro.org; Manivannan Sadhasivam manivannan.sadhasivam@linaro.org Subject: Re: [PATCH v5 28/28] arm: dts: sl28: sync dtbs
On Wed, Nov 10, 2021 at 09:47:30AM +0100, Michael Walle wrote:
Am 2021-10-13 18:14, schrieb Michael Walle:
Copy the board device tree files from linux v5.14. On top of the v5.14 dtbs the changes of these two patches are included here which are needed for u-boot:
https://lore.kernel.org/linux-devicetree/20210831134013.1625527-7-mi chael@walle.cc/
https://lore.kernel.org/linux-devicetree/20210831134013.1625527-8-mi chael@walle.cc/
At the time of this writing the patches were accepted and will be included in 5.15.
Signed-off-by: Michael Walle michael@walle.cc Reviewed-by: Vladimir Oltean vladimir.oltean@nxp.com
Ping.
I have some more patches which depends on this. TBH this is really frustrating if you have to wait serveral months until you can continue development.
I want to chime in and say that I am also unhappy with how long it is taking to get these patches merged, as they fix some rather grievous errors that should not have been introduced to start with. These must come in for this release ASAP.
-- Tom
Sorry, Got occupied with some critical work. Moreover, this was a big series and impacted NXP platforms , so it required thorough review from stakeholders. Submitted the pull-request .
Regards Priyanka
participants (4)
-
Michael Walle -
Priyanka Jain (OSS) -
Tom Rini -
Z.Q. Hou