Resyc DTS files with Linux 5.17-rc5.

Signed-off-by: Adam Ford aford173@gmail.com

diff --git a/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts b/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts index 7675bc3fa8..cb08aa62d9 100644 --- a/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts +++ b/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts @@ -9,5 +9,13 @@

/ { model = "LogicPD Zoom OMAP35xx Torpedo Development Kit"; - compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3"; + compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3430", "ti,omap3"; +}; + +&omap3_pmx_core { + isp1763_pins: pinmux_isp1763_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat6.gpio_128 */ + >; + }; }; diff --git a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts index 18c27e8505..07ea822fe4 100644 --- a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts @@ -50,6 +50,20 @@ }; };

+&uart2 { + /delete-property/dma-names; + bluetooth { + compatible = "ti,wl1283-st"; + enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */ + max-speed = <3000000>; + }; +}; + +/* The DM3730 has a faster L3 than OMAP35, so increase pixel clock */ +&mt9p031_out { + pixel-clock-frequency = <90000000>; +}; + &omap3_pmx_core { mmc3_pins: pinmux_mm3_pins { pinctrl-single,pins = < @@ -71,3 +85,12 @@ >; }; }; + +/* The gpio muxing between omap3530 and dm3730 is different for GPIO_128 */ +&omap3_pmx_wkup { + isp1763_pins: pinmux_isp1763_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a58, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_128 */ + >; + }; +}; diff --git a/arch/arm/dts/logicpd-torpedo-baseboard.dtsi b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi index 642e809e75..b4664ab002 100644 --- a/arch/arm/dts/logicpd-torpedo-baseboard.dtsi +++ b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi @@ -65,6 +65,7 @@ pinctrl-0 = <&pwm_pins>; ti,timers = <&timer10>; #pwm-cells = <3>; + ti,clock-source = <0x01>; };

}; @@ -80,6 +81,8 @@ };

&mcbsp2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; status = "okay"; };

@@ -90,7 +93,8 @@

&gpmc { ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ - 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + 1 0 0x2c000000 0x1000000 /* CS1: 16MB for LAN9221 */ + 6 0 0x28000000 0x1000000>; /* CS6: 16MB for ISP1763 */

ethernet@gpmc { pinctrl-names = "default"; @@ -99,16 +103,60 @@ interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ reg = <1 0 0xff>; }; + + usb@6,0 { + pinctrl-names = "default"; + pinctrl-0 = <&isp1763_pins>; + compatible = "nxp,usb-isp1763"; + reg = <0x6 0x0 0xff>; + interrupt-parent = <&gpio5>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host"; + bus-width = <16>; + dr_mode = "host"; + gpmc,mux-add-data = <0>; + gpmc,device-width = <2>; + gpmc,wait-pin = <0>; + gpmc,burst-length = <4>; + gpmc,cycle2cycle-samecsen = <1>; + gpmc,cycle2cycle-diffcsen = <1>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <45>; + gpmc,cs-wr-off-ns = <45>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <0>; + gpmc,adv-wr-off-ns = <0>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <45>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <25>; + gpmc,rd-cycle-ns = <60>; + gpmc,wr-cycle-ns = <45>; + gpmc,access-ns = <35>; + gpmc,page-burst-access-ns = <0>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <60>; + gpmc,wait-monitoring-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wr-data-mux-bus-ns = <5>; + gpmc,wr-access-ns = <20>; + }; };

+&hdqw1w { + pinctrl-names = "default"; + pinctrl-0 = <&hdq_pins>; +}; + + &vpll2 { regulator-always-on; };

&dss { - status = "ok"; + status = "okay"; vdds_dsi-supply = <&vpll2>; - vdda_video-supply = <&video_reg>; + vdda_video-supply = <&vpll2>; pinctrl-names = "default"; pinctrl-0 = <&dss_dpi_pins1>; port { @@ -124,44 +172,19 @@ display0 = &lcd0; };

- video_reg: video_reg { - pinctrl-names = "default"; - pinctrl-0 = <&panel_pwr_pins>; - compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ - }; - lcd0: display { - compatible = "panel-dpi"; + /* This isn't the exact LCD, but the timings meet spec */ + compatible = "newhaven,nhd-4.3-480272ef-atxl"; label = "15"; - status = "okay"; - /* default-on; */ pinctrl-names = "default"; - + pinctrl-0 = <&panel_pwr_pins>; + backlight = <&bl>; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; port { lcd_in: endpoint { remote-endpoint = <&dpi_out>; }; }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <4>; - vsync-len = <11>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <1>; - }; };

bl: backlight { @@ -193,6 +216,12 @@ >; };

+ hdq_pins: hdq_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE0) /* hdq_sio */ + >; + }; + pwm_pins: pinmux_pwm_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ diff --git a/arch/arm/dts/logicpd-torpedo-som.dtsi b/arch/arm/dts/logicpd-torpedo-som.dtsi index 3fdd0a72f8..3a5228562b 100644 --- a/arch/arm/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/dts/logicpd-torpedo-som.dtsi @@ -35,6 +35,11 @@ }; };

+/* The Torpedo doesn't route the USB host pins */ +&usbhshost { + status = "disabled"; +}; + &gpmc { ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */

@@ -192,3 +197,7 @@ &twl_gpio { ti,use-leds; }; + +&twl_keypad { + status = "disabled"; +};