Loongson 1C is a cost-effective SOC chip for industrial control and the Internet of Things. The Loongson 1C includes a floating-point processing unit, supports multiple types of memory, and supports high-capacity MLC NAND Flash. Loongson 1C provides developers with a wealth of peripheral interfaces and on-chip modules, including Camera controller, USB OTG and USB HOST interfaces, AC97/I2S controller, LCD controller, SPI interface, UART interface, etc., providing sufficient computing power and multi-application connectivity.

Some highlights of this SoC are: - Single core LS232, MIPS32 instruction set compatible, main frequency 300MHZ - 16KB data cache and 16KB instruction cache - 64 bit float unit, hardware division - 8/16 bit SDRAM controller, 45 ~ 133MHz - 8/16 bit SRAM, NAND - I2S/AC97, LCD, MAC, USB, OTG, SPI, I2C, PWM, CAN, SDIO, ADC - 12 UARTs

See Techinical Reference Manual for details: https://www.loongson.cn/ https://github.com/hodcarrier/ls1c300_bsp

Signed-off-by: Du Huanpeng dhu@hodcarrier.org --- MAINTAINERS | 15 +++++ arch/mips/Kconfig | 11 ++++ arch/mips/Makefile | 1 + arch/mips/dts/Makefile | 1 + arch/mips/mach-lsmips/Kconfig | 76 ++++++++++++++++++++++++++ arch/mips/mach-lsmips/Makefile | 6 ++ arch/mips/mach-lsmips/ls1c300/Makefile | 7 +++ configs/ls1c300_defconfig | 53 ++++++++++++++++++ 8 files changed, 170 insertions(+) create mode 100644 arch/mips/mach-lsmips/Kconfig create mode 100644 arch/mips/mach-lsmips/Makefile create mode 100644 arch/mips/mach-lsmips/ls1c300/Makefile create mode 100644 configs/ls1c300_defconfig

diff --git a/MAINTAINERS b/MAINTAINERS index 87991cccdd..91d6d714d8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1116,6 +1116,21 @@ F: drivers/net/cortina_ni.c F: drivers/net/cortina_ni.h F: drivers/net/phy/ca_phy.c

+MIPS LOONGSON LS1C300 +M: Du Huanpeng dhu@hodcarrier.org +S: Maintained +F: arch/mips/dts/loongson32-ls1c300b.dtsi +F: arch/mips/dts/ls1c300-eval.dts +F: arch/mips/mach-lsmips/ +F: board/loongson/ls1c300-eval/ +F: configs/ls1c300_defconfig +F: drivers/clk/lsmips/ +F: drivers/reset/reset-lsmips.c +F: drivers/watchdog/lsmips_wdt.c +F: include/configs/ls1c300.h +F: include/dt-bindings/clock/ls1c300-clk.h +F: include/dt-bindings/reset/ls1c300-reset.h + MIPS MEDIATEK M: Weijie Gao weijie.gao@mediatek.com R: GSS_MTK_Uboot_upstream GSS_MTK_Uboot_upstream@mediatek.com diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 569f5f48bc..fa2d9af9ba 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -88,6 +88,16 @@ config ARCH_MTMIPS select SUPPORTS_LITTLE_ENDIAN select SUPPORT_SPL

+config ARCH_LSMIPS + bool "Support Loongson MIPS platforms" + select DM + select DM_SERIAL + select OF_CONTROL + select SUPPORTS_CPU_MIPS32_R1 + select SUPPORTS_CPU_MIPS32_R2 + select SUPPORTS_LITTLE_ENDIAN + select SUPPORT_SPL + config ARCH_JZ47XX bool "Support Ingenic JZ47xx" select SUPPORT_SPL @@ -173,6 +183,7 @@ source "arch/mips/mach-bmips/Kconfig" source "arch/mips/mach-jz47xx/Kconfig" source "arch/mips/mach-pic32/Kconfig" source "arch/mips/mach-mtmips/Kconfig" +source "arch/mips/mach-lsmips/Kconfig" source "arch/mips/mach-octeon/Kconfig"

if MIPS diff --git a/arch/mips/Makefile b/arch/mips/Makefile index a007914590..342cea6655 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -19,6 +19,7 @@ machine-$(CONFIG_ARCH_BMIPS) += bmips machine-$(CONFIG_ARCH_JZ47XX) += jz47xx machine-$(CONFIG_MACH_PIC32) += pic32 machine-$(CONFIG_ARCH_MTMIPS) += mtmips +machine-$(CONFIG_ARCH_LSMIPS) += lsmips machine-$(CONFIG_ARCH_MSCC) += mscc machine-${CONFIG_ARCH_OCTEON} += octeon

diff --git a/arch/mips/dts/Makefile b/arch/mips/dts/Makefile index 1b179116c9..5cb7490a79 100644 --- a/arch/mips/dts/Makefile +++ b/arch/mips/dts/Makefile @@ -21,6 +21,7 @@ dtb-$(CONFIG_BOARD_MT7621_NAND_RFB) += mediatek,mt7621-nand-rfb.dtb dtb-$(CONFIG_BOARD_MT7628_RFB) += mediatek,mt7628-rfb.dtb dtb-$(CONFIG_BOARD_GARDENA_SMART_GATEWAY_MT7688) += gardena-smart-gateway-mt7688.dtb dtb-$(CONFIG_BOARD_LINKIT_SMART_7688) += linkit-smart-7688.dtb +dtb-$(CONFIG_BOARD_LS1C300) += ls1c300-eval.dtb dtb-$(CONFIG_TARGET_OCTEON_EBB7304) += mrvl,octeon-ebb7304.dtb dtb-$(CONFIG_TARGET_OCTEON_NIC23) += mrvl,octeon-nic23.dtb dtb-$(CONFIG_BOARD_NETGEAR_CG3100D) += netgear,cg3100d.dtb diff --git a/arch/mips/mach-lsmips/Kconfig b/arch/mips/mach-lsmips/Kconfig new file mode 100644 index 0000000000..4f9c4e36ef --- /dev/null +++ b/arch/mips/mach-lsmips/Kconfig @@ -0,0 +1,76 @@ +menu "Loongson MIPS platforms" + depends on ARCH_LSMIPS + +config SYS_MALLOC_F_LEN + default 0x1000 + +config SYS_SOC + default "ls1c300" if SOC_LS1C300 + +config SYS_DCACHE_SIZE + default 16384 + +config SYS_DCACHE_LINE_SIZE + default 32 + +config SYS_ICACHE_SIZE + default 16384 + +config SYS_ICACHE_LINE_SIZE + default 32 + +config TEXT_BASE + default 0xbfc00000 if !SPL + default 0x80200000 if SPL + +config SPL_TEXT_BASE + default 0xbfc00000 + +config SPL_PAYLOAD + default "u-boot-lzma.img" if SPL_LZMA + +config BUILD_TARGET + default "u-boot-with-spl.bin" if SPL + default "u-boot.bin" if !SPL + +choice + prompt "Loongson MIPS SoC select" + +config SOC_LS1C300 + bool "LS1C300" + select CLK_CCF + select SPL_SEPARATE_BSS if SPL + select SPL_INIT_STACK_WITHOUT_MALLOC_F if SPL + select SPL_LOADER_SUPPORT if SPL + select SPL_OF_CONTROL if SPL_DM + select SPL_SIMPLE_BUS if SPL_DM + select SPL_DM_SERIAL if SPL_DM + select SPL_CLK if SPL_DM && SPL_SERIAL + select SPL_SYSRESET if SPL_DM + select SPL_OF_LIBFDT if SPL_OF_CONTROL + help + This supports Loongson LS1C300 + +endchoice + +choice + prompt "Board select" + +config BOARD_LS1C300 + bool "Loongson LS1C300 Eval" + depends on SOC_LS1C300 + help + ls1c300-eval board has a LS1C300 SoC with 64MiB of SDRAM + and 512KiB of flash (SPI NOR) and additional NAND storage. + +endchoice + +config CONS_PIN + int "pin group used in uart" + default 0 + help + Select pin group connected to UART for your board. + +source "board/loongson/ls1c300-eval/Kconfig" + +endmenu diff --git a/arch/mips/mach-lsmips/Makefile b/arch/mips/mach-lsmips/Makefile new file mode 100644 index 0000000000..654143a5f7 --- /dev/null +++ b/arch/mips/mach-lsmips/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y += cpu.o +obj-$(CONFIG_SPL_BUILD) += spl.o + +obj-$(CONFIG_SOC_LS1C300) += ls1c300/ diff --git a/arch/mips/mach-lsmips/ls1c300/Makefile b/arch/mips/mach-lsmips/ls1c300/Makefile new file mode 100644 index 0000000000..17b9d6fb9c --- /dev/null +++ b/arch/mips/mach-lsmips/ls1c300/Makefile @@ -0,0 +1,7 @@ +# SPDX-License-Identifier: GPL-2.0 + +obj-y += lowlevel_init.o +obj-y += sdram.o +obj-y += init.o +obj-y += gpio.o +obj-$(CONFIG_SPL_BUILD) += serial.o diff --git a/configs/ls1c300_defconfig b/configs/ls1c300_defconfig new file mode 100644 index 0000000000..5634fb084a --- /dev/null +++ b/configs/ls1c300_defconfig @@ -0,0 +1,53 @@ +CONFIG_MIPS=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_MALLOC_F_LEN=0x40000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_ENV_SIZE=0x1000 +CONFIG_DEFAULT_DEVICE_TREE="ls1c300-eval" +CONFIG_DM_RESET=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_SIZE_LIMIT=0x100000 +CONFIG_SPL=y +CONFIG_SYS_LOAD_ADDR=0x80010000 +CONFIG_ARCH_LSMIPS=y +CONFIG_SPL_PAYLOAD="u-boot.img" +CONFIG_ROM_EXCEPTION_VECTORS=y +CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y +CONFIG_MIPS_BOOT_FDT=y +CONFIG_FIT=y +# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set +CONFIG_LOGLEVEL=9 +CONFIG_DISPLAY_CPUINFO=y +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x10000 +CONFIG_SPL_PAD_TO=0 +CONFIG_SPL_BSS_START_ADDR=0x80010000 +CONFIG_SPL_BSS_MAX_SIZE=0x10000 +CONFIG_SPL_LEGACY_IMAGE_CRC_CHECK=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_NOR_SUPPORT=y +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_XIMG is not set +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_CLK=y +# CONFIG_CMD_LOADS is not set +CONFIG_OF_EMBED=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +# CONFIG_NET is not set +CONFIG_CLK=y +CONFIG_SPL_CLK_CCF=y +# CONFIG_INPUT is not set +# CONFIG_POWER is not set +CONFIG_CONS_INDEX=2 +CONFIG_SPL_SYS_NS16550_SERIAL=y +CONFIG_SYS_NS16550_REG_SIZE=-1 +CONFIG_SPI=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_WATCHDOG=y +CONFIG_SYSRESET_WATCHDOG_AUTO=y +CONFIG_WATCHDOG_TIMEOUT_MSECS=3000 +CONFIG_WDT_LSMIPS=y +CONFIG_REGEX=y +# CONFIG_GZIP is not set

- pinmux setup functions for debug uart - lowlevel initialization: sdram, pll, spi, debug uart

note that, this SoC have NO useable ram after reset, do not use nested call when doing lowlevel_init.

Signed-off-by: Du Huanpeng dhu@hodcarrier.org --- arch/mips/mach-lsmips/cpu.c | 19 +++ arch/mips/mach-lsmips/include/mach/serial.h | 16 +++ arch/mips/mach-lsmips/ls1c300/gpio.c | 66 +++++++++ arch/mips/mach-lsmips/ls1c300/init.c | 62 ++++++++ arch/mips/mach-lsmips/ls1c300/lowlevel_init.S | 135 ++++++++++++++++++ arch/mips/mach-lsmips/ls1c300/sdram.S | 96 +++++++++++++ arch/mips/mach-lsmips/ls1c300/serial.c | 109 ++++++++++++++ arch/mips/mach-lsmips/spl.c | 47 ++++++ include/configs/ls1c300.h | 34 +++++ 9 files changed, 584 insertions(+) create mode 100644 arch/mips/mach-lsmips/cpu.c create mode 100644 arch/mips/mach-lsmips/include/mach/serial.h create mode 100644 arch/mips/mach-lsmips/ls1c300/gpio.c create mode 100644 arch/mips/mach-lsmips/ls1c300/init.c create mode 100644 arch/mips/mach-lsmips/ls1c300/lowlevel_init.S create mode 100644 arch/mips/mach-lsmips/ls1c300/sdram.S create mode 100644 arch/mips/mach-lsmips/ls1c300/serial.c create mode 100644 arch/mips/mach-lsmips/spl.c create mode 100644 include/configs/ls1c300.h

diff --git a/arch/mips/mach-lsmips/cpu.c b/arch/mips/mach-lsmips/cpu.c new file mode 100644 index 0000000000..339088b435 --- /dev/null +++ b/arch/mips/mach-lsmips/cpu.c @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Stefan Roese sr@denx.de + */ + +#include <common.h> +#include <init.h> +#include <malloc.h> +#include <linux/bitops.h> +#include <linux/io.h> +#include <linux/sizes.h> + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE, SZ_256M); + return 0; +} diff --git a/arch/mips/mach-lsmips/include/mach/serial.h b/arch/mips/mach-lsmips/include/mach/serial.h new file mode 100644 index 0000000000..4da1cb434c --- /dev/null +++ b/arch/mips/mach-lsmips/include/mach/serial.h @@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Gao Weijie weijie.gao@mediatek.com + * + * Copyright (C) 2022 Du Huanpeng dhu@hodcarrier.org + */ + +#ifndef __LSMIPS_SERIAL_H_ +#define __LSMIPS_SERIAL_H_ + +void lsmips_spl_serial_init(void); +int gpio_set_alternate(int gpio, int func); + +#endif /* __LSMIPS_SERIAL_H_ */ diff --git a/arch/mips/mach-lsmips/ls1c300/gpio.c b/arch/mips/mach-lsmips/ls1c300/gpio.c new file mode 100644 index 0000000000..2195738b2b --- /dev/null +++ b/arch/mips/mach-lsmips/ls1c300/gpio.c @@ -0,0 +1,66 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2022 Du Huanpeng dhu@hodcarrier.org + */ + +#include <linux/errno.h> +#include <asm/bitops.h> + +#define CBUS_FIRST0 0xbfd011c0 +#define CBUS_SECOND0 0xbfd011d0 +#define CBUS_THIRD0 0xbfd011e0 +#define CBUS_FOURTHT0 0xbfd011f0 +#define CBUS_FIFTHT0 0xbfd01200 + +#define CBUS_FIRST1 0xbfd011c4 +#define CBUS_SECOND1 0xbfd011d4 +#define CBUS_THIRD1 0xbfd011e4 +#define CBUS_FOURTHT1 0xbfd011f4 +#define CBUS_FIFTHT1 0xbfd01204 + +#define CBUS_FIRST2 0xbfd011c8 +#define CBUS_SECOND2 0xbfd011d8 +#define CBUS_THIRD2 0xbfd011e8 +#define CBUS_FOURTHT2 0xbfd011f8 +#define CBUS_FIFTHT2 0xbfd01208 + +#define CBUS_FIRST3 0xbfd011cc +#define CBUS_SECOND3 0xbfd011dc +#define CBUS_THIRD3 0xbfd011ec +#define CBUS_FOURTHT3 0xbfd011fc +#define CBUS_FIFTHT3 0xbfd0120c + +/* + * pinmux for debug uart and spl only, for others, please + * use a pinctrl driver and device-tree for pin muxing. + * + * @gpio: gpio number + * @func: alternate function 1 to 5, 0 for GPIO. + */ + +int gpio_set_alternate(int gpio, int func) +{ + volatile void __iomem *addr; + int i; + + if (gpio < 0 || gpio > 104) + return -ENODEV; + if (func < 0 || func > 5) + return -EINVAL; + + if (func) { + i = func - 1; + addr = (void *)CBUS_FIRST0 + i * 16; + set_bit(gpio, addr); + } else { + /* GPIO, clear CBUS 1 ~ 5 */ + i = 5; + } + + while (i--) { + addr = (void *)CBUS_FIRST0 + 16 * i; + clear_bit(gpio, addr); + } + + return 0; +} diff --git a/arch/mips/mach-lsmips/ls1c300/init.c b/arch/mips/mach-lsmips/ls1c300/init.c new file mode 100644 index 0000000000..0d5576fddf --- /dev/null +++ b/arch/mips/mach-lsmips/ls1c300/init.c @@ -0,0 +1,62 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Gao Weijie weijie.gao@mediatek.com + * + * based on: arch/mips/mach-mtmips/mt7628/init.c + * Copyright (C) 2020-2022 Du Huanpeng dhu@hodcarrier.org + */ + +#include <common.h> +#include <clk.h> +#include <dm.h> +#include <dm/uclass.h> +#include <dt-bindings/clock/ls1c300-clk.h> +#include <linux/io.h> +#include <linux/sizes.h> + +DECLARE_GLOBAL_DATA_PTR; + +int print_cpuinfo(void) +{ + struct udevice *udev; + struct clk clk; + int ret; + ulong xtal; + char buf[SZ_32]; + + printf("CPU: Loongson ls1c300b\n"); + + ret = uclass_get_device_by_driver(UCLASS_CLK, DM_DRIVER_GET(ls1c300_clk), &udev); + if (ret) { + printf("error: clock driver not found.\n"); + return 0; + } + + clk.dev = udev; + + ret = clk_request(udev, &clk); + if (ret < 0) + return ret; + + clk.id = CLK_XTAL; + xtal = clk_get_rate(&clk); + + clk.id = CLK_CPU_THROT; + gd->cpu_clk = clk_get_rate(&clk); + + clk.id = CLK_APB; + gd->mem_clk = clk_get_rate(&clk); + + printf("Clock: CPU: %sMHz, ", strmhz(buf, gd->cpu_clk)); + printf("SDRAM: %sMHz, ", strmhz(buf, gd->mem_clk)); + printf("XTAL: %sMHz\n", strmhz(buf, xtal)); + + return 0; +} + +ulong notrace get_tbclk(void) +{ + return gd->cpu_clk / 2; +} diff --git a/arch/mips/mach-lsmips/ls1c300/lowlevel_init.S b/arch/mips/mach-lsmips/ls1c300/lowlevel_init.S new file mode 100644 index 0000000000..4b453df621 --- /dev/null +++ b/arch/mips/mach-lsmips/ls1c300/lowlevel_init.S @@ -0,0 +1,135 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Gao Weijie weijie.gao@mediatek.com + * + * Copyright (C) 2020-2023 Du Huanpeng dhu@hodcarrier.org + */ + +#include <config.h> +#include <asm-offsets.h> +#include <asm/cacheops.h> +#include <asm/regdef.h> +#include <asm/mipsregs.h> +#include <asm/addrspace.h> +#include <asm/asm.h> +#include <linux/sizes.h> + +/* PLL control register */ +#define NAND_BASE 0xbfe70000 +#define START_FREQ 0x8030 +#define CLK_DIV_PARAM 0x8034 +#define CPU_THROT 0xc010 + +/* START_FREQ */ +#define PLL_VALID 31 +#define Reserved_24 24 +#define FRAC_N 16 +#define M_PLL 8 +#define Reserved_4 4 +#define RST_TIME 2 +#define SDRAM_DIV 0 + #define SDRAM_DIV2 0 + #define SDRAM_DIV4 1 + #define SDRAM_DIV3 2 + +/* CLK_DIV_PARAM */ +#define PIX_DIV 24 +#define CAM_DIV 16 +#define CPU_DIV 8 +#define PIX_DIV_VALID 5 +#define PIX_SEL 4 +#define CAM_DIV_VALID 3 +#define CAM_SEL 2 +#define CPU_DIV_VALID 1 +#define CPU_SEL 0 + +/* Document: + * Freq_PLL = XIN *(M_PLL + FRAC_N)/4 + */ +#define XIN 24000000 +#define PLL_VALID_1 (1<<PLL_VALID) +#define PREP_M_PLL(Freq_PLL) (((Freq_PLL * 4) / XIN) << M_PLL) +#define PREP_SDRAM_DIV(div) (div<<SDRAM_DIV) +#define PREP_CPU_DIV(div1) ((0x80|div1)<<CPU_DIV | (div1&&div1)<<CPU_DIV_VALID) +#define PREP_PIX_DIV(div2) (div2<<PIX_DIV) +#define PREP_CAM_DIV(div3) (div3<<CAM_DIV) + +/* PLL @264MHz, CPU @132MHz, SDRAM @66MHz */ +#define CFG_START_FREQ (PLL_VALID_1 | PREP_M_PLL(264000000) | SDRAM_DIV2) +#define CFG_CLK_DIV_PARAM (PREP_CPU_DIV(2) | PREP_PIX_DIV(0x24) | PREP_CAM_DIV(0x24)) +#define CFG_CPU_THROT 15 + +/* SPI0 control register */ +#define SPI0_BASE 0xbfe80000 +#define SPCR 0 +#define SPSR 1 +#define TxFIFO 2 +#define RxFIFO 2 +#define SPER 3 +#define SFC_PARAM 4 + #define CLK_DIV 4 + #define DUAL_IO 3 + #define FAST_READ 2 + #define BURST_EN 1 + #define MEMORY_EN 0 +#define SFC_SOFTCS 5 +#define SFC_TIMING 6 + #define T_FAST 2 + #define T_CSH 0 + + .set noreorder +LEAF(ls1c300_pll_init) +#if !CONFIG_IS_ENABLED(SKIP_LOWLEVEL_INIT) + li t0, NAND_BASE + li t1, CFG_START_FREQ + li t2, CFG_CLK_DIV_PARAM + li t3, CFG_CPU_THROT + + sw t3, CPU_THROT (t0) + sw t2, CLK_DIV_PARAM (t0) + sw t1, START_FREQ (t0) + + ori t2, 1<<CPU_SEL + sw t2, CLK_DIV_PARAM (t0) +#endif + li v0, 264000000 + jr ra + nop +END(ls1c300_pll_init) + +LEAF(ls1c300_spi_init) +#if !CONFIG_IS_ENABLED(SKIP_LOWLEVEL_INIT) + li t0, SPI0_BASE + li t1, (1<<MEMORY_EN) | (1<<BURST_EN) | (1<<FAST_READ) | (1<<DUAL_IO) + sb t1, SFC_PARAM (t0) + li t2, (1<<T_FAST) | (1<<T_CSH) + sb t2, SFC_TIMING (t0) +#endif + jr ra + nop +END(ls1c300_spi_init) + +NESTED(lowlevel_init, 0, ra) + /* Save ra and do real lowlevel initialization */ + move s0, ra + /* Setup PLL @264MHz */ + PTR_LA t9, ls1c300_pll_init + jalr t9 + nop + + /* Setup SPI Dual IO@33MHz */ + PTR_LA t9, ls1c300_spi_init + jalr t9 + nop + + /* Setup external SDRAM @66MHz */ + PTR_LA t9, ls1c300_sdram_init + jalr t9 + nop + + move ra, s0 + jr ra + nop +END(lowlevel_init) diff --git a/arch/mips/mach-lsmips/ls1c300/sdram.S b/arch/mips/mach-lsmips/ls1c300/sdram.S new file mode 100644 index 0000000000..4797b1d8a2 --- /dev/null +++ b/arch/mips/mach-lsmips/ls1c300/sdram.S @@ -0,0 +1,96 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2020-2022 Du Huanpeng dhu@hodcarrier.org + */ + +#include <config.h> +#include <asm-offsets.h> +#include <asm/cacheops.h> +#include <asm/regdef.h> +#include <asm/mipsregs.h> +#include <asm/addrspace.h> +#include <asm/asm.h> +#include <linux/sizes.h> + +/* sdram control 64 bit register */ +#define SD_CONFIG 0xbfd00000 +#define SD_CONFIGHI 0x414 +#define SD_CONFIGLO 0x410 + +#define CONFIG_VALID 41 +#define HANG_UP 40 +#define DEF_SEL 39 +#define TWR 37 +#define TREF 25 +#define TRAS 21 +#define TRFC 17 +#define TRP 14 +#define TCL 11 +#define TRCD 8 + +#define SD_BIT 6 + #define SD_8BIT (0<<SD_BIT) + #define SD_16BIT (1<<SD_BIT) + #define SD_32BIT (2<<SD_BIT) +#define SD_CSIZE 3 + #define SD_CSIZE_512 (0<<SD_CSIZE) + #define SD_CSIZE_1K (1<<SD_CSIZE) + #define SD_CSIZE_2K (2<<SD_CSIZE) + #define SD_CSIZE_4K (3<<SD_CSIZE) + #define SD_CSIZE_256 (7<<SD_CSIZE) +#define SD_RSIZE 0 + #define SD_RSIZE_2K (0<<SD_RSIZE) + #define SD_RSIZE_4K (1<<SD_RSIZE) + #define SD_RSIZE_8K (2<<SD_RSIZE) + #define SD_RSIZE_16K (3<<SD_RSIZE) + +#define SD_CFG_1(tWR, tREF, tRAS, tRFC, tRP, tCL, tRCD) \ + ((tWR<<TWR)|(tREF<<TREF)|(tRAS<<TRAS)|(tRFC<<TRFC)|(tRP<<TRP)|(tCL<<TCL)|(tRCD<<TRCD)) +#define CFG_SD_0(b, c, r) \ + ((b<<SD_BIT)|(c<<SD_CSIZE)|(r<<SD_RSIZE)) +/* + * recommended values by ls1c300 user manual, + * tweak to fit your board. + */ +#define SD_CONFIG_133MHz SD_CFG_1(2, 0x818, 6, 8, 3, 3, 3) +#define SD_CONFIG_100MHz SD_CFG_1(2, 0x620, 5, 6, 2, 3, 2) +#define SD_CONFIG_75MHz SD_CFG_1(1, 0x494, 4, 5, 2, 2, 2) +#define SD_CONFIG_33MHz SD_CFG_1(1, 0x204, 2, 2, 1, 2, 1) + +#define SD_CONFIG_66MHz SD_CFG_1(1, 0x401, 4, 4, 2, 2, 2) + +#define SD_CONFIG64 (SD_CONFIG_66MHz | SD_16BIT | SD_CSIZE_1K | SD_RSIZE_8K) +#define CFG_SDCONFIGHI (SD_CONFIG64 /(1<<32)) +#define CFG_SDCONFIGLO (SD_CONFIG64 %(1<<32)) + + .set noreorder +/* + * Loongson ls1c300 SoC do not have onchip sram for initial stack, + * initialize the external sdram on reset as early as possiable. + */ +LEAF(ls1c300_sdram_init) +#if !CONFIG_IS_ENABLED(SKIP_LOWLEVEL_INIT) + li t0, SD_CONFIG + li t1, CFG_SDCONFIGLO + li t2, CFG_SDCONFIGHI + +/* store twice as the hardware manual required. */ + sw t1, SD_CONFIGLO (t0) + sw t2, SD_CONFIGHI (t0) + sync + + sw t1, SD_CONFIGLO (t0) + sw t2, SD_CONFIGHI (t0) + sync + + ori t2, 1<<(CONFIG_VALID-32) + sw t1, SD_CONFIGLO (t0) + sw t2, SD_CONFIGHI (t0) + sync +#endif + li v0, SZ_64M + jr ra + nop +END(ls1c300_sdram_init) + + diff --git a/arch/mips/mach-lsmips/ls1c300/serial.c b/arch/mips/mach-lsmips/ls1c300/serial.c new file mode 100644 index 0000000000..93fd653385 --- /dev/null +++ b/arch/mips/mach-lsmips/ls1c300/serial.c @@ -0,0 +1,109 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Gao Weijie weijie.gao@mediatek.com + * + * Copyright (C) 2020-2022 Du Huanpeng dhu@hodcarrier.org + */ + +#include <mach/serial.h> +#include <linux/kernel.h> + +struct uart_pin_config { + char port; + char af; + char rx; + char tx; +}; + +struct uart_pin_config con[] = { +#if CONFIG_CONS_INDEX == 0 + { 0, 2, 74, 75 }, + { 0, 3, 23, 24 }, + { 0, 3, 99, 100 }, + +#elif CONFIG_CONS_INDEX == 1 + { 1, 1, 17, 18 }, + { 1, 1, 101, 102 }, + { 1, 2, 40, 41 }, + { 1, 4, 2, 3 }, + +#elif CONFIG_CONS_INDEX == 2 + { 2, 2, 36, 37 }, + { 2, 2, 42, 43 }, + { 2, 3, 27, 28 }, + { 2, 3, 103, 104 }, + { 2, 4, 4, 5 }, + +#elif CONFIG_CONS_INDEX == 3 + { 3, 2, 17, 18 }, + { 3, 2, 33, 34 }, + { 3, 2, 44, 45 }, + { 3, 4, 0, 1 }, + +#elif CONFIG_CONS_INDEX == 4 + { 4, 5, 23, 24 }, + { 4, 5, 58, 59 }, + { 4, 5, 80, 79 }, + +#elif CONFIG_CONS_INDEX == 5 + { 5, 5, 25, 26 }, + { 5, 5, 60, 61 }, + { 5, 5, 81, 78 }, + +#elif CONFIG_CONS_INDEX == 6 + { 6, 5, 27, 46 }, + { 6, 5, 62, 63 }, + +#elif CONFIG_CONS_INDEX == 7 + { 7, 5, 57, 56 }, + { 7, 5, 64, 65 }, + { 7, 5, 87, 88 }, + +#elif CONFIG_CONS_INDEX == 8 + { 8, 5, 55, 54 }, + { 8, 5, 66, 67 }, + { 8, 5, 89, 90 }, + +#elif CONFIG_CONS_INDEX == 9 + { 9, 5, 53, 52 }, + { 9, 5, 68, 69 }, + { 9, 5, 85, 86 }, + +#elif CONFIG_CONS_INDEX == 10 + { 10, 5, 51, 50 }, + { 10, 5, 70, 71 }, + { 10, 5, 84, 82 }, + +#elif CONFIG_CONS_INDEX == 11 + { 11, 5, 49, 48 }, + { 11, 5, 72, 73 }, +#endif /* CONFIG_CONS_INDEX */ +}; + +#define UART2_RX 36 +#define UART2_TX 37 +#define AFUNC 2 + +void lsmips_spl_serial_init(void) +{ +#if defined(CONFIG_SPL_SERIAL) + int pin_rx, pin_tx; + int afunc; + + if (CONFIG_CONS_PIN < ARRAY_SIZE(con)) { + pin_rx = con[CONFIG_CONS_PIN].rx; + pin_tx = con[CONFIG_CONS_PIN].tx; + afunc = con[CONFIG_CONS_PIN].af; + } else { + pin_rx = UART2_RX; + pin_tx = UART2_TX; + afunc = AFUNC; + } + + gpio_set_alternate(pin_rx, afunc); + gpio_set_alternate(pin_tx, afunc); +#endif /* CONFIG_SPL_SERIAL */ + return; +} diff --git a/arch/mips/mach-lsmips/spl.c b/arch/mips/mach-lsmips/spl.c new file mode 100644 index 0000000000..c7c28989f2 --- /dev/null +++ b/arch/mips/mach-lsmips/spl.c @@ -0,0 +1,47 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved. + * + * Author: Gao Weijie weijie.gao@mediatek.com + * + * Copyright (C) 2022 Du Huanpeng dhu@hodcarrier.org + */ + +#include <common.h> +#include <init.h> +#include <spl.h> +#include <asm/sections.h> +#include <linux/libfdt.h> +#include <linux/sizes.h> +#include <mach/serial.h> + +void __noreturn board_init_f(ulong dummy) +{ + spl_init(); + +#ifdef CONFIG_SPL_SERIAL + /* + * lsmips_spl_serial_init() is useful if debug uart is enabled, + * or DM based serial is not enabled. + */ + lsmips_spl_serial_init(); + preloader_console_init(); +#endif + + board_init_r(NULL, 0); +} + +void board_boot_order(u32 *spl_boot_list) +{ + spl_boot_list[0] = BOOT_DEVICE_NOR; +} + +unsigned long spl_nor_get_uboot_base(void) +{ + void *uboot_base = __image_copy_end; + + if (fdt_magic(uboot_base) == FDT_MAGIC) + return (unsigned long)uboot_base + fdt_totalsize(uboot_base); + + return (unsigned long)uboot_base; +} diff --git a/include/configs/ls1c300.h b/include/configs/ls1c300.h new file mode 100644 index 0000000000..4d07b07759 --- /dev/null +++ b/include/configs/ls1c300.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Gao Weijie weijie.gao@mediatek.com + * based on: include/configs/mt7628.h + * Copyright (C) 2022-2023 Du Huanpeng dhu@hodcarrier.org + */ + +#ifndef __CONFIG_LS1C300_H__ +#define __CONFIG_LS1C300_H__ + +#define CFG_SYS_SDRAM_BASE 0x80000000 +#define CFG_SYS_INIT_SP_OFFSET 0x2000 + +/* Serial SPL */ +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_SERIAL) +#define CFG_SYS_NS16550_CLK 66000000 +#define CFG_SYS_NS16550_COM1 0xbfe44000 +#define CFG_SYS_NS16550_COM2 0xbfe48000 +#define CFG_SYS_NS16550_COM3 0xbfe4c000 +#define CFG_SYS_NS16550_COM4 0xbfe4c400 +#define CFG_SYS_NS16550_COM5 0xbfe4c500 +#define CFG_SYS_NS16550_COM6 0xbfe4c600 +#endif + +/* Serial common */ +#define CFG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 } + +/* SPL */ +#define CFG_MALLOC_F_ADDR 0x80100000 /* FIXME: find a proper place */ +#define CFG_SYS_UBOOT_BASE 0xbd000000 + +#endif /* __CONFIG_LS1C300_H__ */

- devicetree for ls1c300 SoC and board - setup debug uart pins

Signed-off-by: Du Huanpeng dhu@hodcarrier.org --- arch/mips/dts/loongson32-ls1c300b.dtsi | 150 ++++++++++++++++++++++++ arch/mips/dts/ls1c300-eval.dts | 30 +++++ board/loongson/ls1c300-eval/Kconfig | 12 ++ board/loongson/ls1c300-eval/MAINTAINERS | 7 ++ board/loongson/ls1c300-eval/Makefile | 3 + board/loongson/ls1c300-eval/board.c | 20 ++++ 6 files changed, 222 insertions(+) create mode 100644 arch/mips/dts/loongson32-ls1c300b.dtsi create mode 100644 arch/mips/dts/ls1c300-eval.dts create mode 100644 board/loongson/ls1c300-eval/Kconfig create mode 100644 board/loongson/ls1c300-eval/MAINTAINERS create mode 100644 board/loongson/ls1c300-eval/Makefile create mode 100644 board/loongson/ls1c300-eval/board.c

diff --git a/arch/mips/dts/loongson32-ls1c300b.dtsi b/arch/mips/dts/loongson32-ls1c300b.dtsi new file mode 100644 index 0000000000..b2a89d0ae7 --- /dev/null +++ b/arch/mips/dts/loongson32-ls1c300b.dtsi @@ -0,0 +1,150 @@ +// SPDX-License-Identifier: GPL-2.0 +#include <dt-bindings/clock/ls1c300-clk.h> +#include <dt-bindings/reset/ls1c300-reset.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "loongson,ls1c300-soc"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + reg = <0>; + compatible = "loongson,gs232", "mips,mips4Kc"; + clocks = <&acc CLK_CPU_THROT>; + }; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + u-boot,dm-pre-reloc; + + xtal: oscillator { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges; + + acc: clock-controller@1fe78030 { + compatible = "loongson,ls1c300-clk"; + clocks = <&xtal>; + #clock-cells = <1>; + reg = <0x1fe78030 0x8>, <0x1fe7c010 0x4>; + u-boot,dm-pre-reloc; + }; + + uart0: serial@1fe40000 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe40000 0x100>; + status = "disabled"; + }; + + uart1: serial@1fe44000 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe44000 0x100>; + status = "disabled"; + }; + + uart2: serial@1fe48000 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe48000 0x100>; + resets = <&shut_ctrl UART2_SHUT>; + reset-names = "uart2"; + status = "disabled"; + }; + + uart3: serial@1fe4c000 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4c000 0x100>; + status = "disabled"; + }; + + uart4: serial@1fe4c400 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4c400 0x100>; + status = "disabled"; + }; + + uart5: serial@1fe4c500 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4c500 0x100>; + status = "disabled"; + }; + + uart6: serial@1fe4c600 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4c600 0x100>; + status = "disabled"; + }; + + uart7: serial@1fe4c700 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4c700 0x100>; + status = "disabled"; + }; + + uart8: serial@1fe4c800 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4c800 0x100>; + status = "disabled"; + }; + + uart9: serial@1fe4c900 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4c900 0x100>; + status = "disabled"; + }; + + uart10: serial@1fe4ca00 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4ca00 0x100>; + status = "disabled"; + }; + + uart11: serial@1fe4cb00 { + compatible = "loongson,ls1c300-uart", "ns16550a"; + clocks = <&acc CLK_APB>; + reg = <0x1fe4cb00 0x100>; + status = "disabled"; + }; + + wdt: watchdog@1fe5c060 { + compatible = "loongson,ls1c300-wdt"; + clocks = <&acc CLK_APB>; + reg = <0x1fe5c060 0x10>; + }; + + reset-controller { + compatible = "wdt-reboot"; + wdt = <&wdt>; + }; + + shut_ctrl: reset-controller@1fd00420 { + compatible = "loongson,shut_ctrl"; + reg = <0x1fd00420 0x4>; + #reset-cells = <1>; + }; + }; +}; diff --git a/arch/mips/dts/ls1c300-eval.dts b/arch/mips/dts/ls1c300-eval.dts new file mode 100644 index 0000000000..422e7a858c --- /dev/null +++ b/arch/mips/dts/ls1c300-eval.dts @@ -0,0 +1,30 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2022 Du Huanpeng dhu@hodcarrier.org + */ + +/dts-v1/; + +#include "loongson32-ls1c300b.dtsi" + +/ { + compatible = "lsmips,ls1c300-soc"; + model = "ls1c300-eval"; + + aliases { + serial0 = &uart2; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x4000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart2 { + status = "okay"; +}; diff --git a/board/loongson/ls1c300-eval/Kconfig b/board/loongson/ls1c300-eval/Kconfig new file mode 100644 index 0000000000..e427570a83 --- /dev/null +++ b/board/loongson/ls1c300-eval/Kconfig @@ -0,0 +1,12 @@ +if BOARD_LS1C300 + +config SYS_BOARD + default "ls1c300-eval" + +config SYS_VENDOR + default "loongson" + +config SYS_CONFIG_NAME + default "ls1c300" + +endif diff --git a/board/loongson/ls1c300-eval/MAINTAINERS b/board/loongson/ls1c300-eval/MAINTAINERS new file mode 100644 index 0000000000..5420198dab --- /dev/null +++ b/board/loongson/ls1c300-eval/MAINTAINERS @@ -0,0 +1,7 @@ +LS1C300_EVAL BOARD +M: Du Huanpengdhu@hodcarrier.org +S: Maintained +F: board/loongson/ls1c300-eval +F: include/configs/ls1c300.h +F: configs/ls1c300_defconfig +F: arch/mips/dts/ls1c300-eval.dts diff --git a/board/loongson/ls1c300-eval/Makefile b/board/loongson/ls1c300-eval/Makefile new file mode 100644 index 0000000000..db129c5aba --- /dev/null +++ b/board/loongson/ls1c300-eval/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 + +obj-y += board.o diff --git a/board/loongson/ls1c300-eval/board.c b/board/loongson/ls1c300-eval/board.c new file mode 100644 index 0000000000..6809d66515 --- /dev/null +++ b/board/loongson/ls1c300-eval/board.c @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020-2022 Du Huanpeng dhu@hodcarrier.org + */ + +#include <common.h> +#include <mach/serial.h> + +#if defined(CONFIG_DEBUG_UART_BOARD_INIT) + +#define UART2_RX 36 +#define UART2_TX 37 +#define AFUNC 2 + +void board_debug_uart_init(void) +{ + gpio_set_alternate(UART2_TX, AFUNC); + gpio_set_alternate(UART2_RX, AFUNC); +} +#endif

- watchdog driver for ls1c300 with devicetree support

Signed-off-by: Du Huanpeng dhu@hodcarrier.org --- drivers/watchdog/Kconfig | 8 +++ drivers/watchdog/Makefile | 1 + drivers/watchdog/lsmips_wdt.c | 128 ++++++++++++++++++++++++++++++++++ 3 files changed, 137 insertions(+) create mode 100644 drivers/watchdog/lsmips_wdt.c

diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index 646663528a..f60011e5b3 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -171,6 +171,14 @@ config WDT_GPIO doc/device-tree-bindings/watchdog/gpio-wdt.txt for information on how to describe the watchdog in device tree.

+config WDT_LSMIPS + bool "Loongson MIPS watchdog timer support" + depends on WDT + help + Select this to enable watchdog timer for Loongson SoCs. + The watchdog timer is stopped when initialized. + It performs full SoC reset. + config WDT_MAX6370 bool "MAX6370 watchdog timer support" depends on WDT diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile index fd5d9c7376..8afd61a4fc 100644 --- a/drivers/watchdog/Makefile +++ b/drivers/watchdog/Makefile @@ -30,6 +30,7 @@ obj-$(CONFIG_WDT_ORION) += orion_wdt.o obj-$(CONFIG_WDT_CDNS) += cdns_wdt.o obj-$(CONFIG_WDT_FTWDT010) += ftwdt010_wdt.o obj-$(CONFIG_WDT_GPIO) += gpio_wdt.o +obj-$(CONFIG_WDT_LSMIPS) += lsmips_wdt.o obj-$(CONFIG_WDT_MAX6370) += max6370_wdt.o obj-$(CONFIG_WDT_MESON_GXBB) += meson_gxbb_wdt.o obj-$(CONFIG_WDT_MPC8xxx) += mpc8xxx_wdt.o diff --git a/drivers/watchdog/lsmips_wdt.c b/drivers/watchdog/lsmips_wdt.c new file mode 100644 index 0000000000..4a813a40bb --- /dev/null +++ b/drivers/watchdog/lsmips_wdt.c @@ -0,0 +1,128 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Watchdog driver for MediaTek SoCs + * + * Copyright (C) 2018 MediaTek Inc. + * Author: Ryder Lee ryder.lee@mediatek.com + * + * based on: drivers/watchdog/mtk_wdt.c + * Copyright (C) 2020-2023 Du Huanpeng dhu@hodcarrier.org + */ + +#include <common.h> +#include <dm.h> +#include <dm/device_compat.h> +#include <hang.h> +#include <wdt.h> +#include <asm/io.h> +#include <clk.h> + + +struct lsmips_wdt_priv { + void __iomem *base; +#define WDT_EN 0 +#define WDT_TIMER 4 +#define WDT_SET 8 + ulong clock; + unsigned long timeout; +}; + +static int lsmips_wdt_reset(struct udevice *dev) +{ + struct lsmips_wdt_priv *priv = dev_get_priv(dev); + + writel(priv->timeout, priv->base + WDT_TIMER); + writel(1, priv->base + WDT_SET); + + return 0; +} + +static int lsmips_wdt_stop(struct udevice *dev) +{ + struct lsmips_wdt_priv *priv = dev_get_priv(dev); + + writel(0, priv->base + WDT_EN); + return 0; +} + +static int lsmips_wdt_expire_now(struct udevice *dev, ulong flags) +{ + struct lsmips_wdt_priv *priv = dev_get_priv(dev); + + writel(1, priv->base + WDT_EN); + writel(1, priv->base + WDT_TIMER); + writel(1, priv->base + WDT_SET); + + hang(); + return 0; +} + +static int lsmips_wdt_start(struct udevice *dev, u64 timeout_ms, ulong flags) +{ + struct lsmips_wdt_priv *priv = dev_get_priv(dev); + unsigned int timeout; + + timeout = U32_MAX / (priv->clock / 1000UL); + + if (timeout < timeout_ms) + timeout = U32_MAX; + else + timeout = timeout_ms * (priv->clock / 1000UL); + + debug("WDT: reload = %08x\n", timeout); + + writel(1, priv->base + WDT_EN); + writel(timeout, priv->base + WDT_TIMER); + writel(1, priv->base + WDT_SET); + + priv->timeout = timeout; + + return 0; +} + +static int lsmips_wdt_probe(struct udevice *dev) +{ + struct lsmips_wdt_priv *priv = dev_get_priv(dev); + struct clk cl; + ulong clock; + + priv->base = dev_remap_addr(dev); + if (!priv->base) + return -ENOENT; + + if (clk_get_by_index(dev, 0, &cl) == 0) + clock = clk_get_rate(&cl); + + debug("WDT: clock = %ld\n", clock); + + if (IS_ERR_VALUE(clock)) { + dev_err(dev, "failed to get rate\n"); + return clock; + } + + priv->clock = clock; + writel(0, priv->base + WDT_EN); + return 0; +} + +static const struct wdt_ops lsmips_wdt_ops = { + .start = lsmips_wdt_start, + .reset = lsmips_wdt_reset, + .stop = lsmips_wdt_stop, + .expire_now = lsmips_wdt_expire_now, +}; + +static const struct udevice_id lsmips_wdt_ids[] = { + { .compatible = "loongson,ls1c300-wdt"}, + {} +}; + +U_BOOT_DRIVER(lsmips_wdt) = { + .name = "lsmips_wdt", + .id = UCLASS_WDT, + .of_match = lsmips_wdt_ids, + .priv_auto = sizeof(struct lsmips_wdt_priv), + .probe = lsmips_wdt_probe, + .ops = &lsmips_wdt_ops, + .flags = DM_FLAG_PRE_RELOC, +};