Set clock related processing into set_speed logic. And Optimize printing format.

Tested-by: Chris Morgan macromorgan@hotmail.com Signed-off-by: Jon Lin jon.lin@rock-chips.com ---

(no changes since v1)

drivers/spi/rockchip_sfc.c | 83 ++++++++++++++++++-------------------- 1 file changed, 40 insertions(+), 43 deletions(-)

diff --git a/drivers/spi/rockchip_sfc.c b/drivers/spi/rockchip_sfc.c index 4e2b861f22..2028b28e26 100644 --- a/drivers/spi/rockchip_sfc.c +++ b/drivers/spi/rockchip_sfc.c @@ -12,6 +12,7 @@ #include <bouncebuf.h> #include <clk.h> #include <dm.h> +#include <dm/device_compat.h> #include <linux/bitops.h> #include <linux/delay.h> #include <linux/iopoll.h> @@ -116,6 +117,7 @@

/* Master trigger */ #define SFC_DMA_TRIGGER 0x80 +#define SFC_DMA_TRIGGER_START 1

/* Src or Dst addr for master */ #define SFC_DMA_ADDR 0x84 @@ -163,14 +165,12 @@ #define SFC_DMA_TRANS_THRETHOLD (0x40)

/* Maximum clock values from datasheet suggest keeping clock value under - * 150MHz. No minimum or average value is suggested, but the U-boot BSP driver - * has a minimum of 10MHz and a default of 80MHz which seems reasonable. + * 150MHz. No minimum or average value is suggested. */ -#define SFC_MIN_SPEED_HZ (10 * 1000 * 1000) -#define SFC_DEFAULT_SPEED_HZ (80 * 1000 * 1000) -#define SFC_MAX_SPEED_HZ (150 * 1000 * 1000) +#define SFC_MAX_SPEED (150 * 1000 * 1000)

struct rockchip_sfc { + struct udevice *dev; void __iomem *regbase; struct clk hclk; struct clk clk; @@ -197,8 +197,6 @@ static int rockchip_sfc_reset(struct rockchip_sfc *sfc) /* Still need to clear the masked interrupt from RISR */ writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);

- debug("reset\n"); - return err; }

@@ -261,15 +259,11 @@ static int rockchip_sfc_probe(struct udevice *bus) #if CONFIG_IS_ENABLED(CLK) ret = clk_enable(&sfc->hclk); if (ret) - debug("Enable ahb clock fail %s: %d\n", bus->name, ret); + dev_dbg(sfc->dev, "sfc Enable ahb clock fail %s: %d\n", bus->name, ret);

ret = clk_enable(&sfc->clk); if (ret) - debug("Enable clock fail for %s: %d\n", bus->name, ret); - - ret = clk_set_rate(&sfc->clk, SFC_DEFAULT_SPEED_HZ); - if (ret) - debug("Could not set sfc clock for %s: %d\n", bus->name, ret); + dev_dbg(sfc->dev, "sfc Enable clock fail for %s: %d\n", bus->name, ret); #endif

ret = rockchip_sfc_init(sfc); @@ -278,7 +272,8 @@ static int rockchip_sfc_probe(struct udevice *bus)

sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc); sfc->version = rockchip_sfc_get_version(sfc); - sfc->speed = SFC_DEFAULT_SPEED_HZ; + sfc->max_freq = SFC_MAX_SPEED; + sfc->dev = bus;

return 0;

@@ -411,11 +406,11 @@ static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc, ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE; cmd |= plat->cs << SFC_CMD_CS_SHIFT;

- debug("addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n", - op->addr.nbytes, op->addr.buswidth, - op->dummy.nbytes, op->dummy.buswidth); - debug("ctrl=%x cmd=%x addr=%llx len=%x\n", - ctrl, cmd, op->addr.val, len); + dev_dbg(sfc->dev, "sfc addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n", + op->addr.nbytes, op->addr.buswidth, + op->dummy.nbytes, op->dummy.buswidth); + dev_dbg(sfc->dev, "sfc ctrl=%x cmd=%x addr=%llx len=%x\n", + ctrl, cmd, op->addr.val, len);

writel(ctrl, sfc->regbase + SFC_CTRL); writel(cmd, sfc->regbase + SFC_CMD); @@ -492,7 +487,7 @@ static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t d { writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR); - writel(0x1, sfc->regbase + SFC_DMA_TRIGGER); + writel(SFC_DMA_TRIGGER_START, sfc->regbase + SFC_DMA_TRIGGER);

return len; } @@ -500,7 +495,7 @@ static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t d static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc, const struct spi_mem_op *op, u32 len) { - debug("xfer_poll len=%x\n", len); + dev_dbg(sfc->dev, "sfc xfer_poll len=%x\n", len);

if (op->data.dir == SPI_MEM_DATA_OUT) return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len); @@ -516,7 +511,7 @@ static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc, void *dma_buf; int ret;

- debug("xfer_dma len=%x\n", len); + dev_dbg(sfc->dev, "sfc xfer_dma len=%x\n", len);

if (op->data.dir == SPI_MEM_DATA_OUT) { dma_buf = (void *)op->data.buf.out; @@ -564,33 +559,16 @@ static int rockchip_sfc_exec_op(struct spi_slave *mem, u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize); int ret;

-#if CONFIG_IS_ENABLED(CLK) - if (unlikely(mem->max_hz != sfc->speed)) { - ret = clk_set_rate(&sfc->clk, clamp(mem->max_hz, (uint)SFC_MIN_SPEED_HZ, - (uint)SFC_MAX_SPEED_HZ)); - if (ret < 0) { - printf("set_freq=%dHz fail, check if it's the cru support level\n", - mem->max_hz); - return ret; - } - - sfc->max_freq = mem->max_hz; - sfc->speed = mem->max_hz; - debug("set_freq=%dHz real_freq=%dHz\n", sfc->max_freq, sfc->speed); - } -#endif - rockchip_sfc_adjust_op_work((struct spi_mem_op *)op); - rockchip_sfc_xfer_setup(sfc, mem, op, len); if (len) { - if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD) + if (likely(sfc->use_dma) && len >= SFC_DMA_TRANS_THRETHOLD) ret = rockchip_sfc_xfer_data_dma(sfc, op, len); else ret = rockchip_sfc_xfer_data_poll(sfc, op, len);

if (ret != len) { - printf("xfer data failed ret %d dir %d\n", ret, op->data.dir); + dev_err(sfc->dev, "xfer data failed ret %d dir %d\n", ret, op->data.dir);

return -EIO; } @@ -604,13 +582,32 @@ static int rockchip_sfc_adjust_op_size(struct spi_slave *mem, struct spi_mem_op struct rockchip_sfc *sfc = dev_get_plat(mem->dev->parent);

op->data.nbytes = min(op->data.nbytes, sfc->max_iosize); + return 0; }

static int rockchip_sfc_set_speed(struct udevice *bus, uint speed) { - /* We set up speed later for each transmission. - */ + struct rockchip_sfc *sfc = dev_get_plat(bus); + int ret; + + if (speed > sfc->max_freq) + speed = sfc->max_freq; + + if (speed == sfc->speed) + return 0; + +#if CONFIG_IS_ENABLED(CLK) + ret = clk_set_rate(&sfc->clk, speed); + if (ret < 0) { + dev_err(sfc->dev, "set_freq=%dHz fail, check if it's the cru support level\n", + speed); + return ret; + } + sfc->speed = speed; +#else + dev_dbg(sfc->dev, "sfc failed, CLK not support\n"); +#endif return 0; }