From: dillon min dillon.minfei@gmail.com

All these files are add for support rt-thread art-pi board

the detail board information can be found at: https://art-pi.gitee.io/website/

board resources: - stm32h750xbh6 128k flash, 1024k sram - 32MiB sdram - 16MiB spi flash - 8MiB qspi flash - onboard wifi, bt, fm

Add following changes to sync with kernel device tree files: - add stm32h7-pinctrl.dtsi to include pin defines for all stm32h743/50 boards - add stm32h7(5/3)0-pinctrl.dtsi - move gpio(a..k) register defines to stm32h743.dtsi, sync with kernel - introduce stm32h750i-art-pi-u-boot.dtsi for sdram paramter, fmc pins

Signed-off-by: dillon min dillon.minfei@gmail.com ---

v2: sync with kernel device tree files

arch/arm/dts/Makefile | 3 +- arch/arm/dts/stm32h7-pinctrl.dtsi | 340 +++++++++++++++++++++++++++++ arch/arm/dts/stm32h743-pinctrl.dtsi | 307 +------------------------- arch/arm/dts/stm32h743.dtsi | 168 +++++++++++++- arch/arm/dts/stm32h750-pinctrl.dtsi | 11 + arch/arm/dts/stm32h750.dtsi | 5 + arch/arm/dts/stm32h750i-art-pi-u-boot.dtsi | 81 +++++++ arch/arm/dts/stm32h750i-art-pi.dts | 188 ++++++++++++++++ include/dt-bindings/memory/stm32-sdram.h | 2 + 9 files changed, 799 insertions(+), 306 deletions(-) create mode 100644 arch/arm/dts/stm32h7-pinctrl.dtsi create mode 100644 arch/arm/dts/stm32h750-pinctrl.dtsi create mode 100644 arch/arm/dts/stm32h750.dtsi create mode 100644 arch/arm/dts/stm32h750i-art-pi-u-boot.dtsi create mode 100644 arch/arm/dts/stm32h750i-art-pi.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index c671082..0f54801 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -454,7 +454,8 @@ dtb-$(CONFIG_STM32F7) += stm32f746-disco.dtb \ stm32f769-disco.dtb \ stm32746g-eval.dtb dtb-$(CONFIG_STM32H7) += stm32h743i-disco.dtb \ - stm32h743i-eval.dtb + stm32h743i-eval.dtb \ + stm32h750i-art-pi.dtb

dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-a1000.dtb \ diff --git a/arch/arm/dts/stm32h7-pinctrl.dtsi b/arch/arm/dts/stm32h7-pinctrl.dtsi new file mode 100644 index 0000000..ebfd165 --- /dev/null +++ b/arch/arm/dts/stm32h7-pinctrl.dtsi @@ -0,0 +1,340 @@ +/* + * Copyright 2017 - Alexandre Torgue alexandre.torgue@st.com + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/pinctrl/stm32-pinfunc.h> + +&pinctrl { + + gpioa: gpio@58020000 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpiob: gpio@58020400 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 16 16>; + }; + + gpioc: gpio@58020800 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 32 16>; + }; + + gpiod: gpio@58020c00 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 48 16>; + }; + + gpioe: gpio@58021000 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 64 16>; + }; + + gpiof: gpio@58021400 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 80 16>; + }; + + gpiog: gpio@58021800 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 96 16>; + }; + + gpioh: gpio@58021c00 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 112 16>; + }; + + gpioi: gpio@58022000 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 128 16>; + }; + + gpioj: gpio@58022400 { + status = "okay"; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 144 16>; + }; + + gpiok: gpio@58022800 { + status = "okay"; + ngpios = <8>; + gpio-ranges = <&pinctrl 0 160 8>; + }; + + i2c1_pins_a: i2c1-0 { + pins { + pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */ + <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + ethernet_rmii: rmii-0 { + pins { + pinmux = <STM32_PINMUX('G', 11, AF11)>, + <STM32_PINMUX('G', 13, AF11)>, + <STM32_PINMUX('G', 12, AF11)>, + <STM32_PINMUX('C', 4, AF11)>, + <STM32_PINMUX('C', 5, AF11)>, + <STM32_PINMUX('A', 7, AF11)>, + <STM32_PINMUX('C', 1, AF11)>, + <STM32_PINMUX('A', 2, AF11)>, + <STM32_PINMUX('A', 1, AF11)>; + slew-rate = <2>; + }; + }; + + sdmmc1_b4_pins_a: sdmmc1-b4-0 { + pins { + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + }; + + sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 { + pins1 { + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + pins2{ + pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-open-drain; + bias-disable; + }; + }; + + sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 { + pins { + pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */ + }; + }; + + sdmmc2_b4_pins_a: sdmmc2-b4-0 { + pins { + pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC1_D0 */ + <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */ + <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */ + <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */ + <STM32_PINMUX('D', 6, AF11)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + }; + + sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */ + <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */ + <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */ + <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */ + <STM32_PINMUX('D', 6, AF11)>; /* SDMMC1_CK */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + pins2{ + pinmux = <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-open-drain; + bias-disable; + }; + }; + + sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 { + pins { + pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC1_D0 */ + <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC1_D1 */ + <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC1_D2 */ + <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC1_D3 */ + <STM32_PINMUX('D', 6, ANALOG)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 7, ANALOG)>; /* SDMMC1_CMD */ + }; + }; + + sdmmc1_dir_pins_a: sdmmc1-dir-0 { + pins1 { + pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */ + slew-rate = <3>; + drive-push-pull; + bias-pull-up; + }; + pins2{ + pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */ + bias-pull-up; + }; + }; + + sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 { + pins { + pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */ + <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */ + }; + }; + + usart1_pins: usart1-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */ + bias-disable; + }; + }; + + usart2_pins: usart2-0 { + pins1 { + pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */ + bias-disable; + }; + }; + + usart3_pins: usart3-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */ + <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS_DE */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */ + <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */ + bias-disable; + }; + }; + + uart4_pins: uart4-0 { + pins1 { + pinmux = <STM32_PINMUX('A', 0, AF8)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('I', 9, AF8)>; /* UART4_RX */ + bias-disable; + }; + }; + + usbotg_hs_pins_a: usbotg-hs-0 { + pins { + pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */ + <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */ + <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */ + <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */ + <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */ + <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */ + <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */ + <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */ + <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */ + <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */ + <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */ + <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + }; + + spi1_pins: spi1-0 { + pins1 { + pinmux = <STM32_PINMUX('A', 5, AF5)>, + /* SPI1_CLK */ + <STM32_PINMUX('B', 5, AF5)>; + /* SPI1_MOSI */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + pins2 { + pinmux = <STM32_PINMUX('G', 9, AF5)>; + /* SPI1_MISO */ + bias-disable; + }; + }; +}; diff --git a/arch/arm/dts/stm32h743-pinctrl.dtsi b/arch/arm/dts/stm32h743-pinctrl.dtsi index 141083f..6b1e115 100644 --- a/arch/arm/dts/stm32h743-pinctrl.dtsi +++ b/arch/arm/dts/stm32h743-pinctrl.dtsi @@ -1,306 +1,11 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) /* - * Copyright 2017 - Alexandre Torgue alexandre.torgue@st.com - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. + * Copyright (C) STMicroelectronics 2017 - All Rights Reserved + * Author: Alexandre Torgue alexandre.torgue@st.com for STMicroelectronics. */

-#include <dt-bindings/pinctrl/stm32-pinfunc.h> +#include "stm32h7-pinctrl.dtsi"

-/ { - soc { - pinctrl: pin-controller { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32h743-pinctrl"; - ranges = <0 0x58020000 0x3000>; - interrupt-parent = <&exti>; - st,syscfg = <&syscfg 0x8>; - pins-are-numbered; - - gpioa: gpio@58020000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - clocks = <&rcc GPIOA_CK>; - st,bank-name = "GPIOA"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiob: gpio@58020400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x400 0x400>; - clocks = <&rcc GPIOB_CK>; - st,bank-name = "GPIOB"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioc: gpio@58020800 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x800 0x400>; - clocks = <&rcc GPIOC_CK>; - st,bank-name = "GPIOC"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiod: gpio@58020c00 { - gpio-controller; - #gpio-cells = <2>; - reg = <0xc00 0x400>; - clocks = <&rcc GPIOD_CK>; - st,bank-name = "GPIOD"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioe: gpio@58021000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1000 0x400>; - clocks = <&rcc GPIOE_CK>; - st,bank-name = "GPIOE"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiof: gpio@58021400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1400 0x400>; - clocks = <&rcc GPIOF_CK>; - st,bank-name = "GPIOF"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiog: gpio@58021800 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1800 0x400>; - clocks = <&rcc GPIOG_CK>; - st,bank-name = "GPIOG"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioh: gpio@58021c00 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1c00 0x400>; - clocks = <&rcc GPIOH_CK>; - st,bank-name = "GPIOH"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioi: gpio@58022000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x2000 0x400>; - clocks = <&rcc GPIOI_CK>; - st,bank-name = "GPIOI"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioj: gpio@58022400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x2400 0x400>; - clocks = <&rcc GPIOJ_CK>; - st,bank-name = "GPIOJ"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiok: gpio@58022800 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x2800 0x400>; - clocks = <&rcc GPIOK_CK>; - st,bank-name = "GPIOK"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - i2c1_pins_a: i2c1-0 { - pins { - pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */ - <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - ethernet_rmii: rmii-0 { - pins { - pinmux = <STM32_PINMUX('G', 11, AF11)>, - <STM32_PINMUX('G', 13, AF11)>, - <STM32_PINMUX('G', 12, AF11)>, - <STM32_PINMUX('C', 4, AF11)>, - <STM32_PINMUX('C', 5, AF11)>, - <STM32_PINMUX('A', 7, AF11)>, - <STM32_PINMUX('C', 1, AF11)>, - <STM32_PINMUX('A', 2, AF11)>, - <STM32_PINMUX('A', 1, AF11)>; - slew-rate = <2>; - }; - }; - - sdmmc1_b4_pins_a: sdmmc1-b4-0 { - pins { - pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ - <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ - <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ - <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ - <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */ - <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ - slew-rate = <3>; - drive-push-pull; - bias-disable; - }; - }; - - sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 { - pins1 { - pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ - <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ - <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ - <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ - <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */ - slew-rate = <3>; - drive-push-pull; - bias-disable; - }; - pins2{ - pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ - slew-rate = <3>; - drive-open-drain; - bias-disable; - }; - }; - - sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 { - pins { - pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */ - <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */ - <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */ - <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */ - <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */ - <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */ - }; - }; - - sdmmc1_dir_pins_a: sdmmc1-dir-0 { - pins1 { - pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */ - <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */ - <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */ - slew-rate = <3>; - drive-push-pull; - bias-pull-up; - }; - pins2{ - pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */ - bias-pull-up; - }; - }; - - sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 { - pins { - pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */ - <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */ - <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */ - <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */ - }; - }; - - usart1_pins: usart1-0 { - pins1 { - pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */ - bias-disable; - }; - }; - - usart2_pins: usart2-0 { - pins1 { - pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */ - bias-disable; - }; - }; - - usbotg_hs_pins_a: usbotg-hs-0 { - pins { - pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */ - <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */ - <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */ - <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */ - <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */ - <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */ - <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */ - <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */ - <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */ - <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */ - <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */ - <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */ - bias-disable; - drive-push-pull; - slew-rate = <2>; - }; - }; - }; - }; +&pinctrl{ + compatible = "st,stm32h743-pinctrl"; }; diff --git a/arch/arm/dts/stm32h743.dtsi b/arch/arm/dts/stm32h743.dtsi index e4e4723..4b4c0b0 100644 --- a/arch/arm/dts/stm32h743.dtsi +++ b/arch/arm/dts/stm32h743.dtsi @@ -99,6 +99,22 @@ clocks = <&rcc USART2_CK>; };

+ usart3: serial@40004800 { + compatible = "st,stm32h7-uart"; + reg = <0x40004800 0x400>; + interrupts = <39>; + status = "disabled"; + clocks = <&rcc USART3_CK>; + }; + + uart4: serial@40004c00 { + compatible = "st,stm32h7-uart"; + reg = <0x40004c00 0x400>; + interrupts = <52>; + status = "disabled"; + clocks = <&rcc UART4_CK>; + }; + i2c1: i2c@40005400 { compatible = "st,stm32f7-i2c"; #address-cells = <1>; @@ -123,7 +139,7 @@ status = "disabled"; };

- i2c3: i2c@40005C00 { + i2c3: i2c@40005c00 { compatible = "st,stm32f7-i2c"; #address-cells = <1>; #size-cells = <0>; @@ -238,7 +254,7 @@

dmamux1: dma-router@40020800 { compatible = "st,stm32h7-dmamux"; - reg = <0x40020800 0x1c>; + reg = <0x40020800 0x40>; #dma-cells = <3>; dma-channels = <16>; dma-requests = <128>; @@ -318,7 +334,7 @@ dma-requests = <32>; };

- sdmmc1: sdmmc@52007000 { + sdmmc1: mmc@52007000 { compatible = "arm,pl18x", "arm,primecell"; arm,primecell-periphid = <0x10153180>; reg = <0x52007000 0x1000>; @@ -332,6 +348,20 @@ max-frequency = <120000000>; };

+ sdmmc2: mmc@48022400 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x10153180>; + reg = <0x48022400 0x400>; + interrupts = <124>; + interrupt-names = "cmd_irq"; + clocks = <&rcc SDMMC2_CK>; + clock-names = "apb_pclk"; + resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <120000000>; + }; + exti: interrupt-controller@58000000 { compatible = "st,stm32h7-exti"; interrupt-controller; @@ -356,7 +386,7 @@ status = "disabled"; };

- i2c4: i2c@58001C00 { + i2c4: i2c@58001c00 { compatible = "st,stm32f7-i2c"; #address-cells = <1>; #size-cells = <0>; @@ -519,6 +549,136 @@ snps,pbl = <8>; status = "disabled"; }; + + pinctrl: pin-controller@58020000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x58020000 0x3000>; + interrupt-parent = <&exti>; + st,syscfg = <&syscfg 0x8>; + pins-are-numbered; + + gpioa: gpio@58020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + clocks = <&rcc GPIOA_CK>; + st,bank-name = "GPIOA"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpiob: gpio@58020400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x400 0x400>; + clocks = <&rcc GPIOB_CK>; + st,bank-name = "GPIOB"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpioc: gpio@58020800 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x800 0x400>; + clocks = <&rcc GPIOC_CK>; + st,bank-name = "GPIOC"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpiod: gpio@58020c00 { + gpio-controller; + #gpio-cells = <2>; + reg = <0xc00 0x400>; + clocks = <&rcc GPIOD_CK>; + st,bank-name = "GPIOD"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpioe: gpio@58021000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1000 0x400>; + clocks = <&rcc GPIOE_CK>; + st,bank-name = "GPIOE"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpiof: gpio@58021400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1400 0x400>; + clocks = <&rcc GPIOF_CK>; + st,bank-name = "GPIOF"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpiog: gpio@58021800 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1800 0x400>; + clocks = <&rcc GPIOG_CK>; + st,bank-name = "GPIOG"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpioh: gpio@58021c00 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1c00 0x400>; + clocks = <&rcc GPIOH_CK>; + st,bank-name = "GPIOH"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpioi: gpio@58022000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2000 0x400>; + clocks = <&rcc GPIOI_CK>; + st,bank-name = "GPIOI"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpioj: gpio@58022400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2400 0x400>; + clocks = <&rcc GPIOJ_CK>; + st,bank-name = "GPIOJ"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + + gpiok: gpio@58022800 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2800 0x400>; + clocks = <&rcc GPIOK_CK>; + st,bank-name = "GPIOK"; + interrupt-controller; + #interrupt-cells = <2>; + status = "disabled"; + }; + }; }; };

diff --git a/arch/arm/dts/stm32h750-pinctrl.dtsi b/arch/arm/dts/stm32h750-pinctrl.dtsi new file mode 100644 index 0000000..24e9997 --- /dev/null +++ b/arch/arm/dts/stm32h750-pinctrl.dtsi @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) STMicroelectronics 2021 - All Rights Reserved + * Author: Dillon Min dillon.minfei@gmail.com for STMicroelectronics. + */ + +#include "stm32h7-pinctrl.dtsi" + +&pinctrl{ + compatible = "st,stm32h750-pinctrl"; +}; diff --git a/arch/arm/dts/stm32h750.dtsi b/arch/arm/dts/stm32h750.dtsi new file mode 100644 index 0000000..99533f3 --- /dev/null +++ b/arch/arm/dts/stm32h750.dtsi @@ -0,0 +1,5 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */ + +#include "stm32h743.dtsi" + diff --git a/arch/arm/dts/stm32h750i-art-pi-u-boot.dtsi b/arch/arm/dts/stm32h750i-art-pi-u-boot.dtsi new file mode 100644 index 0000000..326a553 --- /dev/null +++ b/arch/arm/dts/stm32h750i-art-pi-u-boot.dtsi @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include <stm32h7-u-boot.dtsi> + +&fmc { + /* + * Memory configuration from sdram datasheet W9825G6KH + * first bank is bank@0 + * second bank is bank@1 + */ + bank1: bank@0 { + st,sdram-control = /bits/ 8 <NO_COL_9 + NO_ROW_13 + MWIDTH_16 + BANKS_4 + CAS_2 + SDCLK_3 + RD_BURST_EN + RD_PIPE_DL_0>; + st,sdram-timing = /bits/ 8 <TMRD_2 + TXSR_6 + TRAS_6 + TRC_6 + TRP_2 + TWR_2 + TRCD_2>; + st,sdram-refcount = <677>; + }; +}; + +&pinctrl { + fmc_pins: fmc@0 { + pins { + pinmux = <STM32_PINMUX('D', 0, AF12)>, + <STM32_PINMUX('D', 1, AF12)>, + <STM32_PINMUX('D', 8, AF12)>, + <STM32_PINMUX('D', 9, AF12)>, + <STM32_PINMUX('D',10, AF12)>, + <STM32_PINMUX('D',14, AF12)>, + <STM32_PINMUX('D',15, AF12)>, + + <STM32_PINMUX('E', 0, AF12)>, + <STM32_PINMUX('E', 1, AF12)>, + <STM32_PINMUX('E', 7, AF12)>, + <STM32_PINMUX('E', 8, AF12)>, + <STM32_PINMUX('E', 9, AF12)>, + <STM32_PINMUX('E',10, AF12)>, + <STM32_PINMUX('E',11, AF12)>, + <STM32_PINMUX('E',12, AF12)>, + <STM32_PINMUX('E',13, AF12)>, + <STM32_PINMUX('E',14, AF12)>, + <STM32_PINMUX('E',15, AF12)>, + + <STM32_PINMUX('F', 0, AF12)>, + <STM32_PINMUX('F', 1, AF12)>, + <STM32_PINMUX('F', 2, AF12)>, + <STM32_PINMUX('F', 3, AF12)>, + <STM32_PINMUX('F', 4, AF12)>, + <STM32_PINMUX('F', 5, AF12)>, + <STM32_PINMUX('F',11, AF12)>, + <STM32_PINMUX('F',12, AF12)>, + <STM32_PINMUX('F',13, AF12)>, + <STM32_PINMUX('F',14, AF12)>, + <STM32_PINMUX('F',15, AF12)>, + + <STM32_PINMUX('G', 0, AF12)>, + <STM32_PINMUX('G', 1, AF12)>, + <STM32_PINMUX('G', 2, AF12)>, + <STM32_PINMUX('G', 4, AF12)>, + <STM32_PINMUX('G', 5, AF12)>, + <STM32_PINMUX('G', 8, AF12)>, + <STM32_PINMUX('G',15, AF12)>, + + <STM32_PINMUX('H', 5, AF12)>, + <STM32_PINMUX('C', 2, AF12)>, + <STM32_PINMUX('C', 3, AF12)>; + + slew-rate = <3>; + }; + }; +}; diff --git a/arch/arm/dts/stm32h750i-art-pi.dts b/arch/arm/dts/stm32h750i-art-pi.dts new file mode 100644 index 0000000..dd81198 --- /dev/null +++ b/arch/arm/dts/stm32h750i-art-pi.dts @@ -0,0 +1,188 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * Copyright 2021 - Dillon Min dillon.minfei@gmail.com + * + */ + +/dts-v1/; +#include "stm32h750.dtsi" +#include "stm32h750-pinctrl.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "RT-Thread STM32H750i-ART-PI board"; + compatible = "st,stm32h750i-art-pi", "st,stm32h750"; + + chosen { + bootargs = "root=/dev/ram"; + stdout-path = "serial0:2000000n8"; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x2000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + linux,cma { + compatible = "shared-dma-pool"; + no-map; + size = <0x100000>; + linux,dma-default; + }; + }; + + aliases { + serial0 = &uart4; + serial1 = &usart3; + }; + + leds { + compatible = "gpio-leds"; + led-red { + gpios = <&gpioi 8 0>; + }; + led-green { + gpios = <&gpioc 15 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + v3v3: regulator-v3v3 { + compatible = "regulator-fixed"; + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + wlan_pwr: regulator-wlan { + compatible = "regulator-fixed"; + + regulator-name = "wl-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&clk_hse { + clock-frequency = <25000000>; +}; + +&dma1 { + status = "okay"; +}; + +&dma2 { + status = "okay"; +}; + +&mac { + status = "disabled"; + pinctrl-0 = <&ethernet_rmii>; + pinctrl-names = "default"; + phy-mode = "rmii"; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + broken-cd; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>; + broken-cd; + non-removable; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&wlan_pwr>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +&spi1 { + status = "okay"; + pinctrl-0 = <&spi1_pins>; + pinctrl-names = "default"; + cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>; + dmas = <&dmamux1 37 0x400 0x05>, + <&dmamux1 38 0x400 0x05>; + dma-names = "rx", "tx"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "winbond,w25q128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + + partition@0 { + label = "root filesystem"; + reg = <0 0x1000000>; + }; + }; +}; + +&usart2 { + pinctrl-0 = <&usart2_pins>; + pinctrl-names = "default"; + status = "disabled"; +}; + +&usart3 { + pinctrl-names = "default"; + pinctrl-0 = <&usart3_pins>; + dmas = <&dmamux1 45 0x400 0x05>, + <&dmamux1 46 0x400 0x05>; + dma-names = "rx", "tx"; + st,hw-flow-ctrl; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>; + max-speed = <115200>; + }; +}; + +&uart4 { + pinctrl-0 = <&uart4_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/include/dt-bindings/memory/stm32-sdram.h b/include/dt-bindings/memory/stm32-sdram.h index ab91d2b..90ef2e1 100644 --- a/include/dt-bindings/memory/stm32-sdram.h +++ b/include/dt-bindings/memory/stm32-sdram.h @@ -34,8 +34,10 @@ #define TXSR_1 (1 - 1) #define TXSR_6 (6 - 1) #define TXSR_7 (7 - 1) +#define TXSR_8 (8 - 1) #define TRAS_1 (1 - 1) #define TRAS_4 (4 - 1) +#define TRAS_6 (6 - 1) #define TRC_6 (6 - 1) #define TWR_1 (1 - 1) #define TWR_2 (2 - 1)

From: dillon min dillon.minfei@gmail.com

strsep will change data from original memory address, in case the memory is in non-sdram/sram place, will run into a bug(hang at SDRAM: )

just add a temporary array to store bank_name[] to fix this bug.

Fixes: f303aaf ("ram: stm32: add second SDRAM bank management")

Signed-off-by: dillon min dillon.minfei@gmail.com Reviewed-by: Patrice Chotard patrice.chotard@foss.st.com ---

v2: no changes

drivers/ram/stm32_sdram.c | 3 +++ 1 file changed, 3 insertions(+)

diff --git a/drivers/ram/stm32_sdram.c b/drivers/ram/stm32_sdram.c index 540ad85..da27677 100644 --- a/drivers/ram/stm32_sdram.c +++ b/drivers/ram/stm32_sdram.c @@ -268,6 +268,7 @@ static int stm32_fmc_of_to_plat(struct udevice *dev) u32 swp_fmc; ofnode bank_node; char *bank_name; + char _bank_name[128] = {0}; u8 bank = 0; int ret;

@@ -300,6 +301,8 @@ static int stm32_fmc_of_to_plat(struct udevice *dev) dev_for_each_subnode(bank_node, dev) { /* extract the bank index from DT */ bank_name = (char *)ofnode_get_name(bank_node); + strcpy(_bank_name, bank_name); + bank_name = _bank_name; strsep(&bank_name, "@"); if (!bank_name) { pr_err("missing sdram bank index");

From: dillon min dillon.minfei@gmail.com

Due to DT kernel synchronisation, add new pinctrl compatible string for stm32h750.

Signed-off-by: dillon min dillon.minfei@gmail.com ---

v2: first add

drivers/pinctrl/pinctrl_stm32.c | 1 + 1 file changed, 1 insertion(+)

diff --git a/drivers/pinctrl/pinctrl_stm32.c b/drivers/pinctrl/pinctrl_stm32.c index 6c98538..c5279c4 100644 --- a/drivers/pinctrl/pinctrl_stm32.c +++ b/drivers/pinctrl/pinctrl_stm32.c @@ -491,6 +491,7 @@ static const struct udevice_id stm32_pinctrl_ids[] = { { .compatible = "st,stm32f746-pinctrl" }, { .compatible = "st,stm32f769-pinctrl" }, { .compatible = "st,stm32h743-pinctrl" }, + { .compatible = "st,stm32h750-pinctrl" }, { .compatible = "st,stm32mp157-pinctrl" }, { .compatible = "st,stm32mp157-z-pinctrl" }, { }