From: Haiying Wang Haiying.Wang@freescale.com

Support P1021MDS board to boot from NAND flash (No NOR flash on this board). And because P1021 only has 256K L2 SRAM, which can not used for final uboot image, this patch also enables the TPL BOOT on P1021MDS so that DDR can be initialized in L2 SRAM through SPD code. So there are three stage uboot images: * nand_spl, pad from 4KB size to 16KB, load tpl_boot from offset 16KB in NAND. * tpl_boot, 112KB size. The env variables are copied to offset 128KB in L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 128KB in NAND. * final uboot image, size is variable depends on the functions enabled.

Signed-off-by: Haiying Wang Haiying.Wang@freescale.com Signed-off-by: Mohit Kumar Mohit.Kumar@freescale.com Signed-off-by: Yu.Liu Yu.Liu@freescale.com

--- Changes made based on 2010.12-rc2 release and changes to use objs instead of libs. MAINTAINERS | 4 + board/freescale/p1021mds/Makefile | 53 +++ board/freescale/p1021mds/config.mk | 31 ++ board/freescale/p1021mds/ddr.c | 162 +++++++ board/freescale/p1021mds/law.c | 38 ++ board/freescale/p1021mds/p1021mds.c | 132 ++++++ board/freescale/p1021mds/pci.c | 105 +++++ board/freescale/p1021mds/tlb.c | 102 +++++ boards.cfg | 1 + include/configs/P1021MDS.h | 568 +++++++++++++++++++++++++ nand_spl/board/freescale/p1021mds/Makefile | 135 ++++++ nand_spl/board/freescale/p1021mds/nand_boot.c | 69 +++ nand_spl/nand_boot_fsl_elbc.c | 6 +- tpl/board/freescale/p1021mds/Makefile | 249 +++++++++++ tpl/board/freescale/p1021mds/tpl_boot.c | 80 ++++ 15 files changed, 1734 insertions(+), 1 deletions(-) create mode 100644 board/freescale/p1021mds/Makefile create mode 100644 board/freescale/p1021mds/config.mk create mode 100644 board/freescale/p1021mds/ddr.c create mode 100644 board/freescale/p1021mds/law.c create mode 100644 board/freescale/p1021mds/p1021mds.c create mode 100644 board/freescale/p1021mds/pci.c create mode 100644 board/freescale/p1021mds/tlb.c create mode 100644 include/configs/P1021MDS.h create mode 100644 nand_spl/board/freescale/p1021mds/Makefile create mode 100644 nand_spl/board/freescale/p1021mds/nand_boot.c create mode 100644 tpl/board/freescale/p1021mds/Makefile create mode 100644 tpl/board/freescale/p1021mds/tpl_boot.c

diff --git a/MAINTAINERS b/MAINTAINERS index f47fca5..350cd3a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -17,6 +17,10 @@ # Board CPU # #########################################################################

+Haiying Wang Haiying.Wang@freescale.com + + P1021MDS P1021 + Poonam Aggrwal poonam.aggrwal@freescale.com

P2020RDB P2020 diff --git a/board/freescale/p1021mds/Makefile b/board/freescale/p1021mds/Makefile new file mode 100644 index 0000000..da3b87b --- /dev/null +++ b/board/freescale/p1021mds/Makefile @@ -0,0 +1,53 @@ +# +# Copyright (C) 2010 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += law.o +COBJS-y += tlb.o +COBJS-y += pci.o +COBJS-y += ddr.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1021mds/config.mk b/board/freescale/p1021mds/config.mk new file mode 100644 index 0000000..ce903f6 --- /dev/null +++ b/board/freescale/p1021mds/config.mk @@ -0,0 +1,31 @@ +# +# Copyright (C) 2010 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# p1021mds board +# + +ifndef NAND_SPL +ifndef TPL_BOOT +ifeq ($(CONFIG_NAND), y) +LDSCRIPT := $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds +endif +endif +endif diff --git a/board/freescale/p1021mds/ddr.c b/board/freescale/p1021mds/ddr.c new file mode 100644 index 0000000..3f08f74 --- /dev/null +++ b/board/freescale/p1021mds/ddr.c @@ -0,0 +1,162 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <i2c.h> +#include <asm/processor.h> +#include <asm/io.h> +#include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +DECLARE_GLOBAL_DATA_PTR; + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd, unsigned int ctrl_num) +{ + int ret; + + /* + * The P1021 only has one DDR controller, and the P1021MDS board has + * only one DIMM slot. + */ + + ret = i2c_read(SPD_EEPROM_ADDRESS1, 0, 1, (u8 *)ctrl_dimms_spd, + sizeof(ddr3_spd_eeprom_t)); + + if (ret) { + debug("DDR: failed to read SPD from address %u\n", + SPD_EEPROM_ADDRESS1); + memset(ctrl_dimms_spd, 0, sizeof(ddr3_spd_eeprom_t)); + } +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * Factors to consider for clock adjust: + */ + popts->clk_adjust = 6; + + /* + * Factors to consider for CPO: + */ + popts->cpo_override = 0x1f; + + /* + * Factors to consider for write data delay: + */ + popts->write_data_delay = 2; + + /* + * Factors to consider for half-strength driver enable: + */ + popts->half_strength_driver_enable = 1; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 1; + popts->rtt_override_value = DDR3_RTT_40_OHM; /* 40 Ohm rtt */ + popts->rtt_wr_override_value = 2; /* Rtt_WR */ + + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xa; + popts->wrlvl_start = 0x8; + /* + * P1021 supports max 32-bit DDR width + */ + popts->data_bus_width = 1; + + /* + * disable on-the-fly burst chop mode for 32 bit data bus + */ + popts->OTF_burst_chop_en = 0; + + /* + * Set fixed 8 beat burst for 32 bit data bus + */ + popts->burst_length = DDR_BL8; +} + +phys_size_t fixed_sdram(void) +{ + ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR; + u32 temp_sdram_cfg; + + set_next_law(0 , LAW_SIZE_512M , LAW_TRGT_IF_DDR_1); + + out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); + out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); + out_be32(&ddr->cs0_config_2, CONFIG_SYS_DDR_CS0_CONFIG_2); + out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL_2); + out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL); + out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL); + out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT); + out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1); + out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_1); + out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); + out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); + out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); + out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); + out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_SDRAM_MODE); + out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_SDRAM_MODE_2); + out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_SDRAM_INTERVAL); + out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL); + out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4); + out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); + out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | SDRAM_CFG_32_BE); + + sync(); + isync(); + + udelay(500); + + /* Let the controller go */ + temp_sdram_cfg = in_be32(&ddr->sdram_cfg); + out_be32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN); + + return 512 * 1024 * 1024; +} + +phys_size_t init_ddr_dram(void) +{ + phys_size_t dram_size = 0; +#ifdef CONFIG_SPD_EEPROM + dram_size = fsl_ddr_sdram(); +#else + dram_size = fixed_sdram(); +#endif + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts("\n DDR: "); + return dram_size; +} diff --git a/board/freescale/p1021mds/law.c b/board/freescale/p1021mds/law.c new file mode 100644 index 0000000..aa24733 --- /dev/null +++ b/board/freescale/p1021mds/law.c @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_TPL_BOOT + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_1), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_1), + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_2), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_2), + SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256K, LAW_TRGT_IF_LBC), +#endif /* !CONFIG_TPL_BOOT */ + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1021mds/p1021mds.c b/board/freescale/p1021mds/p1021mds.c new file mode 100644 index 0000000..5d981e2 --- /dev/null +++ b/board/freescale/p1021mds/p1021mds.c @@ -0,0 +1,132 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <hwconfig.h> +#include <pci.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <asm/mp.h> +#include <i2c.h> +#include <ioports.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <fsl_esdhc.h> +#include <tsec.h> +#include <netdev.h> + +int board_early_init_f(void) +{ + + fsl_lbc_t *lbc = LBC_BASE_ADDR; + +#ifdef CONFIG_MMC + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + setbits_be32(&gur->pmuxcr, + (MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP)); +#endif + + /* Set ABSWP to implement conversion of addresses in the LBC */ + setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR); + + return 0; +} + +int checkboard(void) +{ + printf("Board: P1021 MDS\n"); + + return 0; +} + +phys_size_t initdram(int board_type) +{ + return fsl_ddr_sdram_size(); +} + +#ifdef CONFIG_TSEC_ENET +int board_eth_init(bd_t *bis) +{ + struct tsec_info_struct tsec_info[3]; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif + +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + num++; +#endif + +#ifdef CONFIG_TSEC3 + SET_STD_TSEC_INFO(tsec_info[num], 3); + if (!(in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_SGMII3_DIS)) + tsec_info[num].flags |= TSEC_SGMII; + num++; +#endif + + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + tsec_eth_init(bis, tsec_info, num); + + return pci_eth_init(bis); +} +#endif + +#if defined(CONFIG_OF_BOARD_SETUP) +extern void ft_pci_board_setup(void *blob); + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, base, size); + + ft_pci_board_setup(blob); + +} +#endif +; +#ifdef CONFIG_MP +extern void cpu_mp_lmb_reserve(struct lmb *lmb); + +void board_lmb_reserve(struct lmb *lmb) +{ + cpu_mp_lmb_reserve(lmb); +} +#endif diff --git a/board/freescale/p1021mds/pci.c b/board/freescale/p1021mds/pci.c new file mode 100644 index 0000000..ad00dd7 --- /dev/null +++ b/board/freescale/p1021mds/pci.c @@ -0,0 +1,105 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <common.h> +#include <hwconfig.h> +#include <pci.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <libfdt.h> +#include <fdt_support.h> + +#ifdef CONFIG_PCIE1 +static struct pci_controller pcie1_hose; +#endif /* CONFIG_PCIE1 */ +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif /* CONFIG_PCIE2 */ + +void pci_init_board(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + struct fsl_pci_info pci_info[2]; + u32 devdisr, pordevsr, io_sel; + int first_free_busno = 0; + int num = 0; + + int pcie_ep, pcie_configured; + + devdisr = in_be32(&gur->devdisr); + pordevsr = in_be32(&gur->pordevsr); + io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19; + + debug(" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel); + + if (!(pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS)) + printf(" eTSEC2 is in sgmii mode.\n"); + if (!(pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS)) + printf(" eTSEC3 is in sgmii mode.\n"); + + puts("\n"); +#ifdef CONFIG_PCIE1 + pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel); + + if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)) { + SET_STD_PCIE_INFO(pci_info[num], 1); + pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs); + printf(" PCIE1 connected to Slot as %s (base addr %lx)\n", + pcie_ep ? "End Point" : "Root Complex", + pci_info[num].regs); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie1_hose, first_free_busno); + } else { + printf(" PCIE1: disabled\n"); + } + puts("\n"); +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE); /* disable */ +#endif /* CONFIG_PCIE1 */ + +#ifdef CONFIG_PCIE2 + pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_2, io_sel); + + if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE2)) { + SET_STD_PCIE_INFO(pci_info[num], 2); + pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs); + printf(" PCIE2 connected to Slot as %s (base addr %lx)\n", + pcie_ep ? "End Point" : "Root Complex", + pci_info[num].regs); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie2_hose, first_free_busno); + + } else { + printf(" PCIE2: disabled\n"); + } + puts("\n"); +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE2); /* disable */ +#endif /* CONFIG_PCIE2 */ +} + +void ft_pci_board_setup(void *blob) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/p1021mds/tlb.c b/board/freescale/p1021mds/tlb.c new file mode 100644 index 0000000..4619495 --- /dev/null +++ b/board/freescale/p1021mds/tlb.c @@ -0,0 +1,102 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + +#ifndef CONFIG_TPL_BOOT + /* *I*G* - PCIE */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, (CONFIG_SYS_PCIE2_MEM_VIRT + 0x10000000), + (CONFIG_SYS_PCIE2_MEM_PHYS + 0x10000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, (CONFIG_SYS_PCIE2_MEM_VIRT + 0x10000000), + (CONFIG_SYS_PCIE2_MEM_PHYS + 0x10000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCIE I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_IO_VIRT, CONFIG_SYS_PCIE2_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + /* + * *I*G BCSR/PMC0/PMC1 + */ + SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_256K, 1), +#endif /* !CONFIG_TPL_BOOT */ + + /* *I*G - NAND */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_1M, 1), + +#if defined(CONFIG_NAND_SPL) || defined(CONFIG_TPL_BOOT) + /* *I*G - L2SRAM */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 9, BOOKE_PAGESZ_256K, 1) +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 2209676..5c5c7fe 100644 --- a/boards.cfg +++ b/boards.cfg @@ -480,6 +480,7 @@ P1020RDB powerpc mpc85xx p1_p2_rdb freesca P1020RDB_NAND powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,NAND P1020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,SDCARD P1020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020,SPIFLASH +P1021MDS_NAND powerpc mpc85xx p1021mds freescale - P1021MDS:NAND P1022DS powerpc mpc85xx p1022ds freescale P2010RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010 P2010RDB_NAND powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010,NAND diff --git a/include/configs/P1021MDS.h b/include/configs/P1021MDS.h new file mode 100644 index 0000000..2e3d893 --- /dev/null +++ b/include/configs/P1021MDS.h @@ -0,0 +1,568 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* + * p1021mds board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_TPL_U_BOOT + +#ifdef CONFIG_NAND +#define CONFIG_NAND_U_BOOT +#define CONFIG_RAMBOOT_NAND +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ +#elif CONFIG_TPL_BOOT +#define CONFIG_SYS_TEXT_BASE_TPL 0xf8f81000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_TPL /* start of monitor */ +#else +#define CONFIG_SYS_TEXT_BASE 0x01001000 +#endif +#endif + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx /* MPC8540/60/55/41/48/68/P1021 */ +#define CONFIG_P1021 /* P1021 silicon support */ +#define CONFIG_P1021MDS /* P1021MDS board specific */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_FSL_ELBC /* Has Enhance localbus controller */ + +/* Replace a call to get_clock_freq (after it is implemented)*/ +#define CONFIG_SYS_CLK_FREQ 66666666 +#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_HWCONFIG + + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x1fffffff + +#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of + addresses in the LBC */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR + /* physical addr of CCSRBAR */ +#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR +#else +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#endif +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR + /* PQII uses CONFIG_SYS_IMMR */ + +/* DDR Setup */ +#define CONFIG_FSL_DDR3 +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_SPD +#define CONFIG_SYS_DDR_TLB_START 11 + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 + /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ + +/* These are used when DDR doesn't use SPD. */ +#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 +#define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 +#define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 +#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 +#define CONFIG_SYS_DDR_WRLVL_CNTL 0x86559608 +#define CONFIG_SYS_DDR_CDR_1 0x000eaa00 +#define CONFIG_SYS_DDR_CDR_2 0x00000000 +#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 +#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 +#define CONFIG_SYS_DDR_CONTROL 0x470c0000 /* Type = DDR3 */ +#define CONFIG_SYS_DDR_CONTROL_2 0x04401050 +#define CONFIG_SYS_DDR_DATA_INIT 0x1021babe +#define CONFIG_SYS_DDR_TIMING_3 0x00010000 +#define CONFIG_SYS_DDR_TIMING_0 0x00330004 +#define CONFIG_SYS_DDR_TIMING_1 0x5d5bd746 +#define CONFIG_SYS_DDR_TIMING_2 0x0fa8c8cd +#define CONFIG_SYS_DDR_SDRAM_MODE 0x40461320 +#define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 +#define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x0a280000 +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x03000000 +#define CONFIG_SYS_DDR_TIMING_4 0x00220001 +#define CONFIG_SYS_DDR_TIMING_5 0x03402400 + +#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 +#define CONFIG_SYS_DDR_SBE 0x00010000 + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Config the L2 Cache as L2 SRAM + */ +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) + + +/* + * Memory map + * + * 0x0000_0000 0x1fff_ffff DDR3 512MB cacheable + * 0xa000_0000 0xbfff_ffff PCIE2 Mem 512MB non-cacheable + * 0xc000_0000 0xdfff_ffff PCIE1 Mem 512MB non-cacheable + * 0xffc1_0000 0xffc1_ffff PCIE2 IO range 64K non-cacheable + * 0xffc2_0000 0xffc2_ffff PCIE1 IO range 64K non-cacheable + * 0xf800_0000 0xf800_7fff BCSR on CS1 32KB non-cacheable + * 0xf801_0000 0xf801_ffff PMC1 on CS2 64KB non-cacheable + * 0xf802_0000 0xf802_ffff PMC0 on CS3 64KB non-cacheable + * 0xfc00_0000 0xfdff_ffff NAND on CS0 32MB non-cacheable + * 0xffe0_0000 0xffef_ffff CCSRBAR 1M + */ + + +/* + * Local Bus Definitions + */ + +#define CONFIG_SYS_BCSR_BASE 0xf8000000 +#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE + +#define CONFIG_SYS_PIB_PMC1_BASE 0xf8010000 + /* start of PIB-QOC3(PMC1) 64K */ +#define CONFIG_SYS_PIB_PMC1_BASE_PHYS CONFIG_SYS_PIB_PMC1_BASE + +#define CONFIG_SYS_PIB_PMC0_BASE 0xf8020000 + /* start of PIB-T1/E1(PMC0) 64K */ +#define CONFIG_SYS_PIB_PMC0_BASE_PHYS CONFIG_SYS_PIB_PMC0_BASE + +/* chip select 1 - BCSR*/ +#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +/* chip select 2 - PIB(QOC3-PMC1)*/ +#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC1_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR2_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +/* chip select 3 - PIB(T1/E1-PMC0)*/ +#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC0_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR3_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +#define CONFIG_SYS_NO_FLASH + +#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) \ + || defined(CONFIG_RAMBOOT_SPIFLASH) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_NAND_BASE 0xFFF00000 +#else +#define CONFIG_SYS_NAND_BASE 0xFC000000 +#endif +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) + +/* NAND boot: 4K NAND loader config */ +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_NAND_SPL_SIZE 0x1000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE (112 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) +#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) +#endif +#ifdef CONFIG_TPL_BOOT +/* tpl boot: 112K tpl uboot config*/ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x01000000) +#define CONFIG_SYS_NAND_U_BOOT_START (0x01000000) +#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) +#endif + +/* NAND FLASH CONFIG */ +#define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) +/* chip select 0 - NAND */ +#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SERIAL_MULTI +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) +#ifdef CONFIG_NAND_SPL +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif + +#define CONFIG_BAUDRATE 115200 + +/* Use the HUSH parser*/ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0, 0x69}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * Environment + */ +#if defined(CONFIG_NAND) +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (576 * 1024) +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#endif +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (128 << 10)) + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot Argument Buffer Size */ + +/*********************************/ +#ifndef CONFIG_TPL_BOOT + +#define CONFIG_MP /* Multiprocessor support */ + +#define CONFIG_PCI /* Disable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controller */ +#define CONFIG_PCIE2 /* PCIE controller */ +#define CONFIG_FSL_PCI_INIT /* use common fsl pci init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_TSEC_ENET /* tsec ethernet support */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +#define CONFIG_SYS_64BIT_VSPRINTF +#define CONFIG_SYS_64BIT_STRTOUL + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* TSEC support */ +#if defined(CONFIG_TSEC_ENET) + +/* TSECV2 */ +#define CONFIG_TSECV2 + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI +#endif + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 0 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHYIDX 0 + +#define TSEC2_PHY_ADDR 4 +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_SGMII) +#define TSEC2_PHYIDX 0 + +#ifdef CONFIG_TSEC3_IN_SGMII /* Need to set SW8.6 to 0 */ +#define TSEC3_PHY_ADDR 6 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_SGMII) +#else +#define TSEC3_PHY_ADDR 1 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#endif +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif /* CONFIG_TSEC_ENET */ + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#ifdef CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#endif +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +#define PLPPAR1_I2C_BIT_MASK 0x0000000F +#define PLPPAR1_I2C2_VAL 0x00000000 +#define PLPPAR1_ESDHC_VAL 0x0000000A +#define PLPDIR1_I2C_BIT_MASK 0x0000000F +#define PLPDIR1_I2C2_VAL 0x0000000F +#define PLPDIR1_ESDHC_VAL 0x00000006 + +/* + * General PCI + * Memory Addresses are mapped 1-1. I/O is mapped from 0 + */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64K */ + +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ + +#if defined(CONFIG_PCI) +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ + +#define CONFIG_MMC +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) + /* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_HOSTNAME p1021mds +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_BOOTFILE your.uImage + +#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=your.ramdisk.u-boot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=your.fdt.dtb\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + "ramargs=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + +#define CONFIG_NFSBOOTCOMMAND \ + "run nfsargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "run ramargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr $ramdiskaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* !CONFIG_TPL_BOOT */ +#endif /* __CONFIG_H */ diff --git a/nand_spl/board/freescale/p1021mds/Makefile b/nand_spl/board/freescale/p1021mds/Makefile new file mode 100644 index 0000000..dfea761 --- /dev/null +++ b/nand_spl/board/freescale/p1021mds/Makefile @@ -0,0 +1,135 @@ +# +# Copyright (C) 2010 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +NAND_SPL := y +CONFIG_SYS_TEXT_BASE_SPL := 0xfff00000 +PAD_TO := 0xfff04000 + +include $(TOPDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-nand_spl.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \ + $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_NAND_SPL + +SOBJS = start.o resetvec.o +COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \ + nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +nandobj := $(OBJTREE)/nand_spl/ + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin + +all: $(obj).depend $(ALL) + +$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +# create symbolic links for common files + +$(obj)cache.c: + @rm -f $(obj)cache.c + ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c + +$(obj)cpu_init_early.c: + @rm -f $(obj)cpu_init_early.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_early.c \ + $(obj)cpu_init_early.c + +$(obj)cpu_init_nand.c: + @rm -f $(obj)cpu_init_nand.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c \ + $(obj)cpu_init_nand.c + +$(obj)fsl_law.c: + @rm -f $(obj)fsl_law.c + ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c + +$(obj)law.c: + @rm -f $(obj)law.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c + +$(obj)nand_boot_fsl_elbc.c: + @rm -f $(obj)nand_boot_fsl_elbc.c + ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \ + $(obj)nand_boot_fsl_elbc.c + +$(obj)ns16550.c: + @rm -f $(obj)ns16550.c + ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c + +$(obj)resetvec.S: + @rm -f $(obj)resetvec.S + ln -s $(SRCTREE)/arch/powerpc/cpu/$(CPU)/resetvec.S $(obj)resetvec.S + +$(obj)fixed_ivor.S: + @rm -f $(obj)fixed_ivor.S + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/fixed_ivor.S \ + $(obj)fixed_ivor.S + +$(obj)start.S: $(obj)fixed_ivor.S + @rm -f $(obj)start.S + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/start.S $(obj)start.S + +$(obj)tlb.c: + @rm -f $(obj)tlb.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/tlb.c $(obj)tlb.c + +$(obj)tlb_table.c: + @rm -f $(obj)tlb_table.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c + +ifneq ($(OBJTREE), $(SRCTREE)) +$(obj)nand_boot.c: + @rm -f $(obj)nand_boot.c + ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c \ + $(obj)nand_boot.c +endif + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/freescale/p1021mds/nand_boot.c b/nand_spl/board/freescale/p1021mds/nand_boot.c new file mode 100644 index 0000000..f0f2063 --- /dev/null +++ b/nand_spl/board/freescale/p1021mds/nand_boot.c @@ -0,0 +1,69 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ +#include <common.h> +#include <mpc85xx.h> +#include <asm/io.h> +#include <ns16550.h> +#include <nand.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> + +DECLARE_GLOBAL_DATA_PTR; + +void board_init_f(ulong bootflag) +{ + uint plat_ratio, bus_clk, sys_clk = 0; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + sys_clk = CONFIG_SYS_CLK_FREQ; + + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + bus_clk = plat_ratio * sys_clk; + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + /* copy code to DDR and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0, + CONFIG_SYS_NAND_U_BOOT_RELOC); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/nand_spl/nand_boot_fsl_elbc.c b/nand_spl/nand_boot_fsl_elbc.c index 9547d44..7bd84ce 100644 --- a/nand_spl/nand_boot_fsl_elbc.c +++ b/nand_spl/nand_boot_fsl_elbc.c @@ -4,7 +4,7 @@ * (C) Copyright 2006-2008 * Stefan Roese, DENX Software Engineering, sr@denx.de. * - * Copyright (c) 2008 Freescale Semiconductor, Inc. + * Copyright (c) 2008-2010 Freescale Semiconductor, Inc. * Author: Scott Wood scottwood@freescale.com * * This program is free software; you can redistribute it and/or @@ -47,7 +47,11 @@ static void nand_wait(void) } }

+#ifdef CONFIG_TPL_BOOT +void nand_load(unsigned int offs, int uboot_size, uchar *dst) +#else static void nand_load(unsigned int offs, int uboot_size, uchar *dst) +#endif { fsl_lbc_t *regs = LBC_BASE_ADDR; uchar *buf = (uchar *)CONFIG_SYS_NAND_BASE; diff --git a/tpl/board/freescale/p1021mds/Makefile b/tpl/board/freescale/p1021mds/Makefile new file mode 100644 index 0000000..ffa2e5e --- /dev/null +++ b/tpl/board/freescale/p1021mds/Makefile @@ -0,0 +1,249 @@ +# +# Copyright (C) 2010 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +TPL_BOOT := y +CONFIG_SYS_TEXT_BASE_TPL := 0xf8f81000 +PAD_TO := 0xf8f9c000 + +include $(TOPDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-tpl.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(CONFIG_SYS_TEXT_BASE_TPL) \ + $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_TPL_BOOT +CFLAGS += -DCONFIG_TPL_BOOT + +SOBJS = start.o ticks.o ppcstring.o +COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o speed.o \ + tpl_boot.o tlb.o tlb_table.o ddr-gen3.o ddr.o time.o \ + string.o hwconfig.o time_lib.o ddr_spd.o ctype.o div64.o crc32.o\ + console.o cmd_nvedit.o env_common.o env_nand.o vsprintf.o \ + display_options.o hashtable.o dlmalloc.o stdio.o ns16550.o serial.o \ + errno.o command.o serial_driver.o qsort.o + +ifdef CONFIG_RAMBOOT_NAND +COBJS += nand_boot_fsl_elbc.o +endif + +LIBS = $(OBJTREE)/arch/powerpc/cpu/mpc8xxx/ddr/libddr.o +LIBS += $(OBJTREE)/drivers/i2c/libi2c.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +__LIBS := $(addprefix $(obj), $(LIBS)) +LNDIR := $(OBJTREE)/tpl/board/$(BOARDDIR) + +tplobj := $(OBJTREE)/tpl/ + +ALL = $(tplobj)u-boot-tpl $(tplobj)u-boot-tpl.bin + +all: $(obj).depend $(ALL) + +$(tplobj)u-boot-tpl.bin: $(tplobj)u-boot-tpl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(tplobj)u-boot-tpl: $(OBJS) $(LIBS) + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(__LIBS) $(PLATFORM_LIBS) \ + -Map $(tplobj)u-boot-tpl.map \ + -o $(tplobj)u-boot-tpl + +# create symbolic links for common files + +$(obj)cache.c: + @rm -f $(obj)cache.c + ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c + +$(obj)cpu_init_early.c: + @rm -f $(obj)cpu_init_early.c + ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_early.c $(obj)cpu_init_early.c + +$(obj)cpu_init_nand.c: + @rm -f $(obj)cpu_init_nand.c + ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_nand.c $(obj)cpu_init_nand.c + +$(obj)fsl_law.c: + @rm -f $(obj)fsl_law.c + ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c + +$(obj)law.c: + @rm -f $(obj)law.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c + +$(obj)nand_boot_fsl_elbc.c: + @rm -f $(obj)nand_boot_fsl_elbc.c + ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \ + $(obj)nand_boot_fsl_elbc.c + +$(obj)fixed_ivor.S: + @rm -f $(obj)fixed_ivor.S + ln -sf $(SRCTREE)/$(CPUDIR)/fixed_ivor.S $(obj)fixed_ivor.S + +$(obj)start.S: $(obj)fixed_ivor.S + @rm -f $(obj)start.S + ln -sf $(SRCTREE)/$(CPUDIR)/start.S $(obj)start.S + +$(obj)speed.c: + @rm -f $(obj)speed.c + ln -sf $(SRCTREE)/$(CPUDIR)/speed.c $(obj)speed.c + +$(obj)interrupts.c: + @rm -f $(obj)interrupts.c + ln -sf $(SRCTREE)/arch/powerpc/lib/interrupts.c $(obj)interrupts.c + +$(obj)ticks.S: + @rm -f $(obj)ticks.S + ln -sf $(SRCTREE)/arch/powerpc/lib/ticks.S $(obj)ticks.S + +$(obj)bootm.c: + @rm -f $(obj)bootm.c + ln -sf $(SRCTREE)/arch/powerpc/lib/bootm.c $(obj)bootm.c + +$(obj)tlb.c: + @rm -f $(obj)tlb.c + ln -sf $(SRCTREE)/$(CPUDIR)/tlb.c $(obj)tlb.c + +$(obj)tlb_table.c: + @rm -f $(obj)tlb_table.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c + +$(obj)ddr.c: + @rm -f $(obj)ddr.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/ddr.c $(obj)ddr.c + +$(obj)time.c: + @rm -f $(obj)time.o + ln -sf $(SRCTREE)/arch/powerpc/lib/time.c $(obj)time.c + +$(obj)ddr-gen3.c: + @rm -f $(obj)ddr-gen3.c + ln -sf $(SRCTREE)/$(CPUDIR)/ddr-gen3.c $(obj)ddr-gen3.c + +$(obj)ppcstring.S: + @rm -f $(obj)ppcstring.S + ln -sf $(SRCTREE)/arch/powerpc/lib/ppcstring.S $(obj)ppcstring.S + +$(obj)ns16550.c: + @rm -f $(obj)ns16550.c + ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c + +$(obj)serial_driver.c: + @rm -f $(obj)serial_driver.c + ln -sf $(SRCTREE)/drivers/serial/serial.c $(obj)serial_driver.c + +$(obj)time_lib.c: + @rm -f $(obj)time_lib.o + ln -sf $(SRCTREE)/lib/time.c $(obj)time_lib.c + +$(obj)ddr_spd.c: + @rm -f $(obj)ddr_spd.c + ln -sf $(SRCTREE)/common/ddr_spd.c $(obj)ddr_spd.c + +$(obj)ctype.c: + @rm -f $(obj)ctype.c + ln -sf $(SRCTREE)/lib/ctype.c $(obj)ctype.c + +$(obj)div64.c: + @rm -f $(obj)div64.c + ln -sf $(SRCTREE)/lib/div64.c $(obj)div64.c + +$(obj)crc32.c: + @rm -f $(obj)crc32.c + ln -sf $(SRCTREE)/lib/crc32.c $(obj)crc32.c + +$(obj)env_common.c: + @rm -f $(obj)env_common.c + ln -sf $(SRCTREE)/common/env_common.c $(obj)env_common.c + +$(obj)env_nand.c: + @rm -f $(obj)env_nand.c + ln -sf $(SRCTREE)/common/env_nand.c $(obj)env_nand.c + +$(obj)cmd_nvedit.c: + @rm -f $(obj)cmd_nvedit.c + ln -sf $(SRCTREE)/common/cmd_nvedit.c $(obj)cmd_nvedit.c + +$(obj)console.c: + @rm -f $(obj)console.c + ln -sf $(SRCTREE)/common/console.c $(obj)console.c + +$(obj)dlmalloc.c: + @rm -f $(obj)dlmalloc.c + ln -sf $(SRCTREE)/common/dlmalloc.c $(obj)dlmalloc.c + +$(obj)hwconfig.c: + @rm -f $(obj)hwconfig.c + ln -sf $(SRCTREE)/common/hwconfig.c $(obj)hwconfig.c + +$(obj)stdio.c: + @rm -f $(obj)stdio.c + ln -sf $(SRCTREE)/common/stdio.c $(obj)stdio.c + +$(obj)string.c: + @rm -f $(obj)string.c + ln -sf $(SRCTREE)/lib/string.c $(obj)string.c + +$(obj)vsprintf.c: + @rm -f $(obj)vsprintf.c + ln -sf $(SRCTREE)/lib/vsprintf.c $(obj)vsprintf.c + +$(obj)display_options.c: + @rm -f $(obj)display_options.c + ln -sf $(SRCTREE)/lib/display_options.c $(obj)display_options.c + +$(obj)hashtable.c: + @rm -f $(obj)hashtable.c + ln -sf $(SRCTREE)/lib/hashtable.c $(obj)hashtable.c + +$(obj)serial.c: + @rm -f $(obj)serial.c + ln -sf $(SRCTREE)/common/serial.c $(obj)serial.c + +$(obj)command.c: + @rm -f $(obj)command.c + ln -sf $(SRCTREE)/common/command.c $(obj)command.c + +$(obj)errno.c: + @rm -f $(obj)errno.c + ln -sf $(SRCTREE)/lib/errno.c $(obj)errno.c + +$(obj)qsort.c: + @rm -f $(obj)qsort.c + ln -sf $(SRCTREE)/lib/qsort.c $(obj)qsort.c + +ifneq ($(OBJTREE), $(SRCTREE)) +$(obj)tpl_boot.c: + @rm -f $(obj)tpl_boot.c + ln -s $(SRCTREE)/tpl/freescale/tpl_boot.c $(obj)tpl_boot.c +endif + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/tpl/board/freescale/p1021mds/tpl_boot.c b/tpl/board/freescale/p1021mds/tpl_boot.c new file mode 100644 index 0000000..47d6568 --- /dev/null +++ b/tpl/board/freescale/p1021mds/tpl_boot.c @@ -0,0 +1,80 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ +#include <common.h> +#include <mpc85xx.h> +#include <asm/io.h> +#include <ns16550.h> +#include <nand.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + +extern void nand_load(unsigned int offs, int uboot_size, uchar *dst); +extern phys_size_t init_ddr_dram(void); +ulong load_addr = CONFIG_SYS_LOAD_ADDR; + +void board_init_f(ulong bootflag) +{ + uint plat_ratio, bus_clk, sys_clk = 0; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + sys_clk = CONFIG_SYS_CLK_FREQ; + + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + bus_clk = plat_ratio * sys_clk; + get_clocks(); + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + bus_clk / 16 / CONFIG_BAUDRATE); + + /* load environment */ +#ifdef CONFIG_NAND_U_BOOT + nand_load(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif + + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; + + /* board specific DDR initialization */ + gd->ram_size = init_ddr_dram(); + puts("DRAM:"); + print_size(gd->ram_size, ""); + + puts("\nThird program loader running in sram... "); + + /* + * Load final image to DDR and let it run from there. + */ +#ifdef CONFIG_NAND_U_BOOT + nand_boot(); +#endif +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ +}