(Sorry for the resend; I sent this to the wrong U-Boot mailing list the first time around)

Dom, ddv2005, Gray,

I'm trying to get Signed-off-by lines for all code in the Raspberry Pi Linux kernel trees related to the SDHCI driver (or just everything). The list of relevant commits for SDHCI is below. Can you please check Documentation/SubmittingPatches in the kernel source tree, and if you're able to, provide your Signed-of-by lines for all of the patches I list below that were either authored by you, or passed through you (the latter I assume mainly in the case of Dom who applied these to git).

Related, do you know who the following person is: Grigori Goronzy greg@blackbox; he's the author of at least one patch, but the email address is invalid.

Dom, it'd be great if you could obtain the appropriate S-o-b lines from all contributors to your kernel trees, then rebase these branches and add the appropriate S-o-bs to all the patches. If in the future you make sure that all the git metadata and S-o-b entries are present and valid in all the commits (full name and valid email address), we won't have to go back to people and validate this after the fact again.

Note: the patch list below is every patch that touches the driver. It may be possible to analyze each patch and find only those that touched the specific subset of code that Oleksandr used for U-Boot. I can give that a try if getting S-o-bs for all the patches proves problematic. Of course, that will then simply defer the issue until someone attempts to upstream the whole downstream Linux SDHCI driver into the upstream Linux kernel...

Thanks very much!

rpi-3.2.27:

118e2d3 Allow the number of cycles delay between sdcard peripheral writes to be specified on command line with sdhci-bcm2708.cycle_delay 7042895 Enable low latency mode by default in sdcard driver. Can be disabled with sdhci-bcm2708.enable_llm=0 307d9fb Fix build for non-preempt case. Fix warning e886b45 Add low-latency mode to sdcard driver. Enable with sdhci-bcm2708.enable_llm=1. Thanks ddv2005. 2c671b9 Fix spinlock recursion in sdhci-bcm2708.c 147779e Add module parameter for missing_status quirk. sdhci-bcm2708.missing_status=0 may improve interrupt latency 31c350f sdhci-bcm2708: use multiblock-type transfers for single blocks 3a47543 sdhci-bcm2708: use extension FIFO to buffer DMA transfers 0bf2669 Add sync_after_dma module parameter f1da243 Use ndelay rather than udelay. Thanks lb

Who is lb?

63aa167 Fix bool/int error, part 2 d34d49e Fix bool/int error d7afba1 sdhci-bcm2708: raise DMA sync timeout 84042ac Allow emmc clock to be specified as command line parameter 70b125d sdhci-bcm2708: assume 50 MHz eMMC clock d7156c5 sdhci-bcm2708: add allow_highspeed parameter 8f82daa sdhci-bcm2708: add additional quirks 6ab6d02 sdhci-bcm2708: remove custom clock handling 8390fb8 sdhci-bcm2708: speed up DMA sync 2d05297 sdcard patch improvements from naren

Who is naren?

e9382f7 possible fix for sdcard missing status. Thank naren 2456b9f Replace #if 1 sections by local configuration #defines (tidy) 8a93b2a Fix problem with dma that could corrupt sdcard, especially when L2 enabled 5961574 Fix for mmc timeouts when erasing multiple blocks 031ee3e Main bcm2708 linux port

Are these actually all authored by who git says they are? I notice that the two commits I called out above have a git authorship field of Dom Cobley, even though the patch subject implies someone else wrote them.

rpi-3.6.y:

a2386d3 Fix up issues with rebase f34c715 Allow the number of cycles delay between sdcard peripheral writes to be specified on command line with sdhci-bcm2708.cycle_delay f0dbf1e Enable low latency mode by default in sdcard driver. Can be disabled with sdhci-bcm2708.enable_llm=0 da819bb Fix build for non-preempt case. Fix warning f26afe4 Add low-latency mode to sdcard driver. Enable with sdhci-bcm2708.enable_llm=1. Thanks ddv2005. 641bd2c Fix spinlock recursion in sdhci-bcm2708.c ee410b8 Add module parameter for missing_status quirk. sdhci-bcm2708.missing_status=0 may improve interrupt latency e1ccc32 sdhci-bcm2708: use multiblock-type transfers for single blocks 34eec60 sdhci-bcm2708: use extension FIFO to buffer DMA transfers 1245667 Add sync_after_dma module parameter 0b047fb Use ndelay rather than udelay. Thanks lb 234c311 Fix bool/int error, part 2 27f5be9 Fix bool/int error ab619f6 sdhci-bcm2708: raise DMA sync timeout 1b89d0c Allow emmc clock to be specified as command line parameter 5109353 sdhci-bcm2708: assume 50 MHz eMMC clock ce8e5cb sdhci-bcm2708: add allow_highspeed parameter aa86832 sdhci-bcm2708: add additional quirks e2076c4 sdhci-bcm2708: remove custom clock handling f354b15 sdhci-bcm2708: speed up DMA sync 9c9780e sdcard patch improvements from naren d47f5ca possible fix for sdcard missing status. Thank naren 1ba126b Replace #if 1 sections by local configuration #defines (tidy) 7a69d91 Fix problem with dma that could corrupt sdcard, especially when L2 enabled f5fe324 Fix for mmc timeouts when erasing multiple blocks f5b930b Main bcm2708 linux port