Introduce Socionext F_OSPI controller driver. This controller is used to communicate with slave devices such as SPI flash memories. It supports 4 slave devices and up to 8-bit wide bus, but supports master mode only.

This driver uses spi-mem framework for SPI flash memory access, and can only operate indirect access mode and single data rate mode.

Signed-off-by: Kunihiko Hayashi hayashi.kunihiko@socionext.com --- drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/spi-sn-f-ospi.c | 686 ++++++++++++++++++++++++++++++++++++ 3 files changed, 695 insertions(+) create mode 100644 drivers/spi/spi-sn-f-ospi.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index c6900f449d5f..ff68ffbc0e06 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -451,6 +451,14 @@ config SOFT_SPI Enable Soft SPI driver. This driver is to use GPIO simulate the SPI protocol.

+config SPI_SN_F_OSPI + tristate "Socionext F_OSPI SPI flash controller" + depends on SPI_MEM + help + This enables support for the Socionext F_OSPI controller + for connecting an SPI flash memory over up to 8-bit wide bus. + It supports indirect access mode only. + config SPI_SUNXI bool "Allwinner SoC SPI controllers" default ARCH_SUNXI diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 674d81caae3b..95dba9ac4559 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -67,6 +67,7 @@ obj-$(CONFIG_ROCKCHIP_SFC) += rockchip_sfc.o obj-$(CONFIG_ROCKCHIP_SPI) += rk_spi.o obj-$(CONFIG_SANDBOX_SPI) += sandbox_spi.o obj-$(CONFIG_SPI_SIFIVE) += spi-sifive.o +obj-$(CONFIG_SPI_SN_F_OSPI) += spi-sn-f-ospi.o obj-$(CONFIG_SPI_SUNXI) += spi-sunxi.o obj-$(CONFIG_SH_QSPI) += sh_qspi.o obj-$(CONFIG_STM32_QSPI) += stm32_qspi.o diff --git a/drivers/spi/spi-sn-f-ospi.c b/drivers/spi/spi-sn-f-ospi.c new file mode 100644 index 000000000000..ebf2903d3ea7 --- /dev/null +++ b/drivers/spi/spi-sn-f-ospi.c @@ -0,0 +1,686 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Socionext SPI flash controller F_OSPI driver + * Copyright (C) 2021 Socionext Inc. + */ + +#include <clk.h> +#include <common.h> +#include <dm.h> +#include <dm/device_compat.h> +#include <linux/bitfield.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <spi.h> +#include <spi-mem.h> + +/* Registers */ +#define OSPI_PROT_CTL_INDIR 0x00 +#define OSPI_PROT_MODE_DATA_MASK GENMASK(31, 30) +#define OSPI_PROT_MODE_ALT_MASK GENMASK(29, 28) +#define OSPI_PROT_MODE_ADDR_MASK GENMASK(27, 26) +#define OSPI_PROT_MODE_CODE_MASK GENMASK(25, 24) +#define OSPI_PROT_MODE_SINGLE 0 +#define OSPI_PROT_MODE_DUAL 1 +#define OSPI_PROT_MODE_QUAD 2 +#define OSPI_PROT_MODE_OCTAL 3 +#define OSPI_PROT_DATA_RATE_DATA BIT(23) +#define OSPI_PROT_DATA_RATE_ALT BIT(22) +#define OSPI_PROT_DATA_RATE_ADDR BIT(21) +#define OSPI_PROT_DATA_RATE_CODE BIT(20) +#define OSPI_PROT_SDR 0 +#define OSPI_PROT_DDR 1 +#define OSPI_PROT_BIT_POS_DATA BIT(19) +#define OSPI_PROT_BIT_POS_ALT BIT(18) +#define OSPI_PROT_BIT_POS_ADDR BIT(17) +#define OSPI_PROT_BIT_POS_CODE BIT(16) +#define OSPI_PROT_SAMP_EDGE BIT(12) +#define OSPI_PROT_DATA_UNIT_MASK GENMASK(11, 10) +#define OSPI_PROT_DATA_UNIT_1B 0 +#define OSPI_PROT_DATA_UNIT_2B 1 +#define OSPI_PROT_DATA_UNIT_4B 3 +#define OSPI_PROT_TRANS_DIR_WRITE BIT(9) +#define OSPI_PROT_DATA_EN BIT(8) +#define OSPI_PROT_ALT_SIZE_MASK GENMASK(7, 5) +#define OSPI_PROT_ADDR_SIZE_MASK GENMASK(4, 2) +#define OSPI_PROT_CODE_SIZE_MASK GENMASK(1, 0) + +#define OSPI_CLK_CTL 0x10 +#define OSPI_CLK_CTL_BOOT_INT_CLK_EN BIT(16) +#define OSPI_CLK_CTL_PHA BIT(12) +#define OSPI_CLK_CTL_PHA_180 0 +#define OSPI_CLK_CTL_PHA_90 1 +#define OSPI_CLK_CTL_DIV GENMASK(9, 8) +#define OSPI_CLK_CTL_DIV_1 0 +#define OSPI_CLK_CTL_DIV_2 1 +#define OSPI_CLK_CTL_DIV_4 2 +#define OSPI_CLK_CTL_DIV_8 3 +#define OSPI_CLK_CTL_INT_CLK_EN BIT(0) + +#define OSPI_CS_CTL1 0x14 +#define OSPI_CS_CTL2 0x18 +#define OSPI_SSEL 0x20 +#define OSPI_CMD_IDX_INDIR 0x40 +#define OSPI_ADDR 0x50 +#define OSPI_ALT_INDIR 0x60 +#define OSPI_DMY_INDIR 0x70 +#define OSPI_DAT 0x80 +#define OSPI_DAT_SWP_INDIR 0x90 + +#define OSPI_DAT_SIZE_INDIR 0xA0 +#define OSPI_DAT_SIZE_EN BIT(15) +#define OSPI_DAT_SIZE_MASK GENMASK(10, 0) +#define OSPI_DAT_SIZE_MAX (OSPI_DAT_SIZE_MASK + 1) + +#define OSPI_TRANS_CTL 0xC0 +#define OSPI_TRANS_CTL_STOP_REQ BIT(1) /* RW1AC */ +#define OSPI_TRANS_CTL_START_REQ BIT(0) /* RW1AC */ + +#define OSPI_ACC_MODE 0xC4 +#define OSPI_ACC_MODE_BOOT_DISABLE BIT(0) + +#define OSPI_SWRST 0xD0 +#define OSPI_SWRST_INDIR_WRITE_FIFO BIT(9) /* RW1AC */ +#define OSPI_SWRST_INDIR_READ_FIFO BIT(8) /* RW1AC */ + +#define OSPI_STAT 0xE0 +#define OSPI_STAT_IS_AXI_WRITING BIT(10) +#define OSPI_STAT_IS_AXI_READING BIT(9) +#define OSPI_STAT_IS_SPI_INT_CLK_STOP BIT(4) +#define OSPI_STAT_IS_SPI_IDLE BIT(3) + +#define OSPI_IRQ 0xF0 +#define OSPI_IRQ_CS_DEASSERT BIT(8) +#define OSPI_IRQ_WRITE_BUF_READY BIT(2) +#define OSPI_IRQ_READ_BUF_READY BIT(1) +#define OSPI_IRQ_CS_TRANS_COMP BIT(0) +#define OSPI_IRQ_ALL \ + (OSPI_IRQ_CS_DEASSERT | OSPI_IRQ_WRITE_BUF_READY \ + | OSPI_IRQ_READ_BUF_READY | OSPI_IRQ_CS_TRANS_COMP) + +#define OSPI_IRQ_STAT_EN 0xF4 +#define OSPI_IRQ_SIG_EN 0xF8 + +/* Parameters */ +#define OSPI_NUM_CS 4 +#define OSPI_DUMMY_CYCLE_MAX 255 +#define OSPI_WAIT_MAX_MSEC 100 + +struct f_ospi { + void __iomem *base; + struct udevice *dev; + struct clk clk; + + u32 mode; + u32 max_speed_hz; + u32 num_cs; + u32 chip_select; +}; + +static u32 f_ospi_get_dummy_cycle(const struct spi_mem_op *op) +{ + return (op->dummy.nbytes * 8) / op->dummy.buswidth; +} + +static void f_ospi_clear_irq(struct f_ospi *ospi) +{ + writel(OSPI_IRQ_CS_DEASSERT | OSPI_IRQ_CS_TRANS_COMP, + ospi->base + OSPI_IRQ); +} + +static void f_ospi_enable_irq_status(struct f_ospi *ospi, u32 irq_bits) +{ + u32 val; + + val = readl(ospi->base + OSPI_IRQ_STAT_EN); + val |= irq_bits; + writel(val, ospi->base + OSPI_IRQ_STAT_EN); +} + +static void f_ospi_disable_irq_status(struct f_ospi *ospi, u32 irq_bits) +{ + u32 val; + + val = readl(ospi->base + OSPI_IRQ_STAT_EN); + val &= ~irq_bits; + writel(val, ospi->base + OSPI_IRQ_STAT_EN); +} + +static void f_ospi_disable_irq_output(struct f_ospi *ospi, u32 irq_bits) +{ + u32 val; + + val = readl(ospi->base + OSPI_IRQ_SIG_EN); + val &= ~irq_bits; + writel(val, ospi->base + OSPI_IRQ_SIG_EN); +} + +static int f_ospi_prepare_config(struct f_ospi *ospi) +{ + u32 val, stat0, stat1; + + /* G4: Disable internal clock */ + val = readl(ospi->base + OSPI_CLK_CTL); + val &= ~(OSPI_CLK_CTL_BOOT_INT_CLK_EN | OSPI_CLK_CTL_INT_CLK_EN); + writel(val, ospi->base + OSPI_CLK_CTL); + + /* G5: Wait for stop */ + stat0 = OSPI_STAT_IS_AXI_WRITING | OSPI_STAT_IS_AXI_READING; + stat1 = OSPI_STAT_IS_SPI_IDLE | OSPI_STAT_IS_SPI_INT_CLK_STOP; + + return readl_poll_timeout(ospi->base + OSPI_STAT, + val, (val & (stat0 | stat1)) == stat1, + OSPI_WAIT_MAX_MSEC); +} + +static int f_ospi_unprepare_config(struct f_ospi *ospi) +{ + u32 val; + + /* G11: Enable internal clock */ + val = readl(ospi->base + OSPI_CLK_CTL); + val |= OSPI_CLK_CTL_BOOT_INT_CLK_EN | OSPI_CLK_CTL_INT_CLK_EN; + writel(val, ospi->base + OSPI_CLK_CTL); + + /* G12: Wait for clock to start */ + return readl_poll_timeout(ospi->base + OSPI_STAT, + val, !(val & OSPI_STAT_IS_SPI_INT_CLK_STOP), + OSPI_WAIT_MAX_MSEC); +} + +static void f_ospi_config_clk(struct f_ospi *ospi, u32 device_hz) +{ + long rate_hz = clk_get_rate(&ospi->clk); + u32 div = DIV_ROUND_UP(rate_hz, device_hz); + u32 div_reg; + u32 val; + + if (rate_hz < device_hz) { + dev_warn(ospi->dev, "Device frequency too large: %d\n", + device_hz); + div_reg = OSPI_CLK_CTL_DIV_1; + } else { + if (div == 1) { + div_reg = OSPI_CLK_CTL_DIV_1; + } else if (div == 2) { + div_reg = OSPI_CLK_CTL_DIV_2; + } else if (div <= 4) { + div_reg = OSPI_CLK_CTL_DIV_4; + } else if (div <= 8) { + div_reg = OSPI_CLK_CTL_DIV_8; + } else { + dev_warn(ospi->dev, "Device frequency too small: %d\n", + device_hz); + div_reg = OSPI_CLK_CTL_DIV_8; + } + } + + /* + * G7: Set clock mode + * clock phase is fixed at 180 degrees and configure edge direction + * instead. + */ + val = readl(ospi->base + OSPI_CLK_CTL); + + val &= ~(OSPI_CLK_CTL_PHA | OSPI_CLK_CTL_DIV); + val |= FIELD_PREP(OSPI_CLK_CTL_PHA, OSPI_CLK_CTL_PHA_180) + | FIELD_PREP(OSPI_CLK_CTL_DIV, div_reg); + + writel(val, ospi->base + OSPI_CLK_CTL); +} + +static void f_ospi_config_dll(struct f_ospi *ospi) +{ + /* G8: Configure DLL, nothing */ +} + +static u8 f_ospi_get_mode(struct f_ospi *ospi, int width, int data_size) +{ + u8 mode = OSPI_PROT_MODE_SINGLE; + + switch (width) { + case 1: + mode = OSPI_PROT_MODE_SINGLE; + break; + case 2: + mode = OSPI_PROT_MODE_DUAL; + break; + case 4: + mode = OSPI_PROT_MODE_QUAD; + break; + case 8: + mode = OSPI_PROT_MODE_OCTAL; + break; + default: + if (data_size) + dev_err(ospi->dev, "Invalid buswidth: %d\n", width); + break; + } + + return mode; +} + +static void f_ospi_config_indir_protocol(struct f_ospi *ospi, + const struct spi_mem_op *op) +{ + u8 mode; + u32 prot = 0, val; + int unit; + + /* Set one chip select */ + writel(BIT(ospi->chip_select), ospi->base + OSPI_SSEL); + + mode = f_ospi_get_mode(ospi, op->cmd.buswidth, 1); + prot |= FIELD_PREP(OSPI_PROT_MODE_CODE_MASK, mode); + + mode = f_ospi_get_mode(ospi, op->addr.buswidth, op->addr.nbytes); + prot |= FIELD_PREP(OSPI_PROT_MODE_ADDR_MASK, mode); + + mode = f_ospi_get_mode(ospi, op->data.buswidth, op->data.nbytes); + prot |= FIELD_PREP(OSPI_PROT_MODE_DATA_MASK, mode); + + prot |= FIELD_PREP(OSPI_PROT_DATA_RATE_DATA, OSPI_PROT_SDR); + prot |= FIELD_PREP(OSPI_PROT_DATA_RATE_ALT, OSPI_PROT_SDR); + prot |= FIELD_PREP(OSPI_PROT_DATA_RATE_ADDR, OSPI_PROT_SDR); + prot |= FIELD_PREP(OSPI_PROT_DATA_RATE_CODE, OSPI_PROT_SDR); + + if (ospi->mode & SPI_LSB_FIRST) + prot |= OSPI_PROT_BIT_POS_DATA | OSPI_PROT_BIT_POS_ALT + | OSPI_PROT_BIT_POS_ADDR | OSPI_PROT_BIT_POS_CODE; + + if (ospi->mode & SPI_CPHA) + prot |= OSPI_PROT_SAMP_EDGE; + + /* Examine nbytes % 4 */ + switch (op->data.nbytes & 0x3) { + case 0: + unit = OSPI_PROT_DATA_UNIT_4B; + val = 0; + break; + case 2: + unit = OSPI_PROT_DATA_UNIT_2B; + val = OSPI_DAT_SIZE_EN | (op->data.nbytes - 1); + break; + default: + unit = OSPI_PROT_DATA_UNIT_1B; + val = OSPI_DAT_SIZE_EN | (op->data.nbytes - 1); + break; + } + prot |= FIELD_PREP(OSPI_PROT_DATA_UNIT_MASK, unit); + + switch (op->data.dir) { + case SPI_MEM_DATA_IN: + prot |= OSPI_PROT_DATA_EN; + break; + + case SPI_MEM_DATA_OUT: + prot |= OSPI_PROT_TRANS_DIR_WRITE | OSPI_PROT_DATA_EN; + break; + + case SPI_MEM_NO_DATA: + prot |= OSPI_PROT_TRANS_DIR_WRITE; + break; + + default: + dev_warn(ospi->dev, "Unsupported direction"); + break; + } + + prot |= FIELD_PREP(OSPI_PROT_ADDR_SIZE_MASK, op->addr.nbytes); + prot |= FIELD_PREP(OSPI_PROT_CODE_SIZE_MASK, 1); /* 1byte */ + + writel(prot, ospi->base + OSPI_PROT_CTL_INDIR); + writel(val, ospi->base + OSPI_DAT_SIZE_INDIR); +} + +static int f_ospi_indir_prepare_op(struct f_ospi *ospi, + const struct spi_mem_op *op) +{ + u32 irq_stat_en; + int ret; + + ret = f_ospi_prepare_config(ospi); + if (ret) + return ret; + + f_ospi_config_clk(ospi, ospi->max_speed_hz); + + f_ospi_config_indir_protocol(ospi, op); + + writel(f_ospi_get_dummy_cycle(op), ospi->base + OSPI_DMY_INDIR); + writel(op->addr.val, ospi->base + OSPI_ADDR); + writel(op->cmd.opcode, ospi->base + OSPI_CMD_IDX_INDIR); + + f_ospi_clear_irq(ospi); + + switch (op->data.dir) { + case SPI_MEM_DATA_IN: + irq_stat_en = OSPI_IRQ_READ_BUF_READY | OSPI_IRQ_CS_TRANS_COMP; + break; + + case SPI_MEM_DATA_OUT: + irq_stat_en = OSPI_IRQ_WRITE_BUF_READY | OSPI_IRQ_CS_TRANS_COMP; + break; + + case SPI_MEM_NO_DATA: + irq_stat_en = OSPI_IRQ_CS_TRANS_COMP; + break; + + default: + dev_warn(ospi->dev, "Unsupported direction"); + irq_stat_en = 0; + } + + f_ospi_disable_irq_status(ospi, ~irq_stat_en); + f_ospi_enable_irq_status(ospi, irq_stat_en); + + return f_ospi_unprepare_config(ospi); +} + +static void f_ospi_indir_start_xfer(struct f_ospi *ospi) +{ + /* Write only 1, auto cleared */ + writel(OSPI_TRANS_CTL_START_REQ, ospi->base + OSPI_TRANS_CTL); +} + +static void f_ospi_indir_stop_xfer(struct f_ospi *ospi) +{ + /* Write only 1, auto cleared */ + writel(OSPI_TRANS_CTL_STOP_REQ, ospi->base + OSPI_TRANS_CTL); +} + +static int f_ospi_indir_wait_xfer_complete(struct f_ospi *ospi) +{ + u32 val; + + return readl_poll_timeout(ospi->base + OSPI_IRQ, val, + val & OSPI_IRQ_CS_TRANS_COMP, + OSPI_WAIT_MAX_MSEC); +} + +static int f_ospi_indir_read(struct f_ospi *ospi, + const struct spi_mem_op *op) +{ + u8 *buf = op->data.buf.in; + u32 val; + int i, ret; + + /* E1-2: Prepare transfer operation */ + ret = f_ospi_indir_prepare_op(ospi, op); + if (ret) + goto out; + + f_ospi_indir_start_xfer(ospi); + + /* E3-4: Wait for ready and read data */ + for (i = 0; i < op->data.nbytes; i++) { + ret = readl_poll_timeout(ospi->base + OSPI_IRQ, val, + val & OSPI_IRQ_READ_BUF_READY, + OSPI_WAIT_MAX_MSEC); + if (ret) + goto out; + + buf[i] = readl(ospi->base + OSPI_DAT) & 0xFF; + } + + /* E5-6: Stop transfer if data size is nothing */ + if (!(readl(ospi->base + OSPI_DAT_SIZE_INDIR) & OSPI_DAT_SIZE_EN)) + f_ospi_indir_stop_xfer(ospi); + + /* E7-8: Wait for completion and clear */ + ret = f_ospi_indir_wait_xfer_complete(ospi); + if (ret) + goto out; + + writel(OSPI_IRQ_CS_TRANS_COMP, ospi->base + OSPI_IRQ); + + /* E9: Do nothing if data size is valid */ + if (readl(ospi->base + OSPI_DAT_SIZE_INDIR) & OSPI_DAT_SIZE_EN) + goto out; + + /* E10-11: Reset and check read fifo */ + writel(OSPI_SWRST_INDIR_READ_FIFO, ospi->base + OSPI_SWRST); + + ret = readl_poll_timeout(ospi->base + OSPI_SWRST, val, + !(val & OSPI_SWRST_INDIR_READ_FIFO), + OSPI_WAIT_MAX_MSEC); +out: + return ret; +} + +static int f_ospi_indir_write(struct f_ospi *ospi, + const struct spi_mem_op *op) +{ + u8 *buf = (u8 *)op->data.buf.out; + u32 val; + int i, ret; + + /* F1-3: Prepare transfer operation */ + ret = f_ospi_indir_prepare_op(ospi, op); + if (ret) + goto out; + + f_ospi_indir_start_xfer(ospi); + + if (!(readl(ospi->base + OSPI_PROT_CTL_INDIR) & OSPI_PROT_DATA_EN)) + goto nodata; + + /* F4-5: Wait for buffer ready and write data */ + for (i = 0; i < op->data.nbytes; i++) { + ret = readl_poll_timeout(ospi->base + OSPI_IRQ, val, + val & OSPI_IRQ_WRITE_BUF_READY, + OSPI_WAIT_MAX_MSEC); + if (ret) + goto out; + + writel(buf[i], ospi->base + OSPI_DAT); + } + + /* F6-7: Stop transfer if data size is nothing */ + if (!(readl(ospi->base + OSPI_DAT_SIZE_INDIR) & OSPI_DAT_SIZE_EN)) + f_ospi_indir_stop_xfer(ospi); + +nodata: + /* F8-9: Wait for completion and clear */ + ret = f_ospi_indir_wait_xfer_complete(ospi); + if (ret) + goto out; + + writel(OSPI_IRQ_CS_TRANS_COMP, ospi->base + OSPI_IRQ); +out: + return ret; +} + +static int f_ospi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op) +{ + struct f_ospi *ospi = dev_get_priv(slave->dev->parent); + struct dm_spi_slave_plat *slave_plat; + int err = 0; + + slave_plat = dev_get_parent_plat(slave->dev); + ospi->chip_select = slave_plat->cs; + + switch (op->data.dir) { + case SPI_MEM_DATA_IN: + err = f_ospi_indir_read(ospi, op); + break; + + case SPI_MEM_DATA_OUT: + fallthrough; + case SPI_MEM_NO_DATA: + err = f_ospi_indir_write(ospi, op); + break; + + default: + dev_warn(ospi->dev, "Unsupported direction"); + err = -EOPNOTSUPP; + } + + return err; +} + +static bool f_ospi_supports_op_width(const struct spi_mem_op *op) +{ + u8 width_available[] = { 0, 1, 2, 4, 8 }; + u8 width_op[] = { op->cmd.buswidth, op->addr.buswidth, + op->dummy.buswidth, op->data.buswidth }; + bool is_match_found; + int i, j; + + for (i = 0; i < ARRAY_SIZE(width_op); i++) { + is_match_found = false; + + for (j = 0; j < ARRAY_SIZE(width_available); j++) { + if (width_op[i] == width_available[j]) { + is_match_found = true; + break; + } + } + + if (!is_match_found) + return false; + } + + return true; +} + +static bool f_ospi_supports_op(struct spi_slave *slave, + const struct spi_mem_op *op) +{ + if (f_ospi_get_dummy_cycle(op) > OSPI_DUMMY_CYCLE_MAX) + return false; + + if (op->addr.nbytes > 4) + return false; + + if (!f_ospi_supports_op_width(op)) + return false; + + return true; +} + +static int f_ospi_adjust_op_size(struct spi_slave *slave, struct spi_mem_op *op) +{ + op->data.nbytes = min((int)op->data.nbytes, (int)(OSPI_DAT_SIZE_MAX)); + + return 0; +} + +static const struct spi_controller_mem_ops f_ospi_mem_ops = { + .adjust_op_size = f_ospi_adjust_op_size, + .supports_op = f_ospi_supports_op, + .exec_op = f_ospi_exec_op, +}; + +static int f_ospi_set_speed(struct udevice *bus, u32 speed) +{ + struct f_ospi *ospi = dev_get_priv(bus); + + ospi->max_speed_hz = speed; + + return 0; +} + +static int f_ospi_set_mode(struct udevice *bus, u32 mode) +{ + struct f_ospi *ospi = dev_get_priv(bus); + + ospi->mode = mode; + + return 0; +} + +static int f_ospi_init(struct f_ospi *ospi) +{ + int ret; + + ret = f_ospi_prepare_config(ospi); + if (ret) + return ret; + + /* Disable boot signal */ + writel(OSPI_ACC_MODE_BOOT_DISABLE, ospi->base + OSPI_ACC_MODE); + + f_ospi_config_dll(ospi); + + /* Disable IRQ */ + f_ospi_clear_irq(ospi); + f_ospi_disable_irq_status(ospi, OSPI_IRQ_ALL); + f_ospi_disable_irq_output(ospi, OSPI_IRQ_ALL); + + return f_ospi_unprepare_config(ospi); +} + +static int f_ospi_of_to_plat(struct udevice *dev) +{ + struct f_ospi *ospi = dev_get_priv(dev); + + ospi->base = dev_read_addr_ptr(dev); + ospi->num_cs = dev_read_u32_default(dev, "num-cs", OSPI_NUM_CS); + + return 0; +} + +static int f_ospi_probe(struct udevice *dev) +{ + struct f_ospi *ospi = dev_get_priv(dev); + int ret; + + ospi->dev = dev; + + ret = clk_get_by_index(dev, 0, &ospi->clk); + if (ret < 0) { + dev_err(dev, "Failed to get clock\n"); + goto err_put_ctlr; + } + + ret = clk_enable(&ospi->clk); + if (ret) { + dev_err(dev, "Failed to enable the clock\n"); + goto err_put_ctlr; + } + + ret = f_ospi_init(ospi); + if (ret) + goto err_disable_clk; + + return 0; + +err_disable_clk: + clk_disable(&ospi->clk); + +err_put_ctlr: + dev_err(dev, "Socionext F_OSPI probe failed\n"); + return ret; +} + +static int f_ospi_remove(struct udevice *dev) +{ + struct f_ospi *ospi = dev_get_priv(dev); + + clk_disable(&ospi->clk); + + return 0; +} + +static const struct dm_spi_ops f_ospi_ops = { + .set_speed = f_ospi_set_speed, + .set_mode = f_ospi_set_mode, + .mem_ops = &f_ospi_mem_ops, +}; + +static const struct udevice_id f_ospi_dt_ids[] = { + { .compatible = "socionext,f-ospi" }, + {} +}; + +U_BOOT_DRIVER(f_ospi) = { + .name = "sn-f-ospi", + .id = UCLASS_SPI, + .of_match = f_ospi_dt_ids, + .of_to_plat = f_ospi_of_to_plat, + .ops = &f_ospi_ops, + .probe = f_ospi_probe, + .remove = f_ospi_remove, + .priv_auto = sizeof(struct f_ospi), +};