[U-Boot] [PATCH] cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
Hi,
This adds to the documenation to explain how to use the kwbimage.cfg file necessary to generate an image with prefixed board setup values necessary for the kirkwood boards.
Signed-off-by: Karl O. Pinc kop@meme.com --- doc/README.kwbimage | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)
diff --git a/doc/README.kwbimage b/doc/README.kwbimage index 7f15e6d..e91c387 100644 --- a/doc/README.kwbimage +++ b/doc/README.kwbimage @@ -25,13 +25,24 @@ for ex. -T kwbimage -a 0x00600000 -e 0x00600000 \ -d u-boot.bin u-boot.kwb
+ kwbimage support available with mkimage utility will generate kirkwood boot -image that can be flashed on the board NAND/SPI flash +image that can be flashed on the board NAND/SPI flash. The make target +which uses mkimage to produce such an image is "u-boot.kwb". For example: + + export BUILD_DIR=/tmp/build + make distclean + make yourboard_config + make $BUILD_DIR/u-boot.kwb +
Board specific configuration file specifications: ------------------------------------------------ -1. This file must present in the $(BOARDDIR) and the name should be - kwbimage.cfg (since this is used in Makefile) +1. This file must present in the $(BOARDDIR). The default name is + kwbimage.cfg. The name can be set as part of the full path + to the file using CONFIG_SYS_KWD_CONFIG (probably in + include/configs/<yourboard>.h). The path should look like: + $(SRCTREE)/$(CONFIG_BOARDDIR)/<yourkwbimagename>.cfg 2. This file can have empty lines and lines starting with "#" as first character to put comments 3. This file can have configuration command lines as mentioned below,
-----Original Message----- From: Karl O. Pinc [mailto:kop@meme.com] Sent: 03 August 2012 08:22 To: Prafulla Wadaskar; u-boot@lists.denx.de Cc: Karl O. Pinc Subject: [PATCH] cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
Hi,
This adds to the documenation to explain how to use the kwbimage.cfg file necessary to generate an image with prefixed board setup values necessary for the kirkwood boards.
Signed-off-by: Karl O. Pinc kop@meme.com
doc/README.kwbimage | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)
diff --git a/doc/README.kwbimage b/doc/README.kwbimage index 7f15e6d..e91c387 100644 --- a/doc/README.kwbimage +++ b/doc/README.kwbimage @@ -25,13 +25,24 @@ for ex. -T kwbimage -a 0x00600000 -e 0x00600000 \ -d u-boot.bin u-boot.kwb
kwbimage support available with mkimage utility will generate kirkwood boot -image that can be flashed on the board NAND/SPI flash +image that can be flashed on the board NAND/SPI flash. The make target +which uses mkimage to produce such an image is "u-boot.kwb". For example:
- export BUILD_DIR=/tmp/build
- make distclean
- make yourboard_config
- make $BUILD_DIR/u-boot.kwb
Board specific configuration file specifications:
-1. This file must present in the $(BOARDDIR) and the name should be
- kwbimage.cfg (since this is used in Makefile)
+1. This file must present in the $(BOARDDIR). The default name is
- kwbimage.cfg. The name can be set as part of the full path
to the file using CONFIG_SYS_KWD_CONFIG (probably ininclude/configs/<yourboard>.h). The path should look like:$(SRCTREE)/$(CONFIG_BOARDDIR)/<yourkwbimagename>.cfg
- This file can have empty lines and lines starting with "#" as
first character to put comments 3. This file can have configuration command lines as mentioned below, --
Acked by: Prafulla Wadaskar prafulla@marvell.com
I will pull this patch latter.
Regards... Prafulla . . .
-----Original Message----- From: Prafulla Wadaskar Sent: 03 August 2012 11:58 To: 'Karl O. Pinc'; u-boot@lists.denx.de Subject: RE: [PATCH] cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
-----Original Message----- From: Karl O. Pinc [mailto:kop@meme.com] Sent: 03 August 2012 08:22 To: Prafulla Wadaskar; u-boot@lists.denx.de Cc: Karl O. Pinc Subject: [PATCH] cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
Hi,
This adds to the documenation to explain how to use the kwbimage.cfg file necessary to generate an image with prefixed board setup values necessary for the kirkwood boards.
Signed-off-by: Karl O. Pinc kop@meme.com
doc/README.kwbimage | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)
diff --git a/doc/README.kwbimage b/doc/README.kwbimage index 7f15e6d..e91c387 100644 --- a/doc/README.kwbimage +++ b/doc/README.kwbimage @@ -25,13 +25,24 @@ for ex. -T kwbimage -a 0x00600000 -e 0x00600000 \ -d u-boot.bin u-boot.kwb
kwbimage support available with mkimage utility will generate kirkwood boot -image that can be flashed on the board NAND/SPI flash +image that can be flashed on the board NAND/SPI flash. The make target +which uses mkimage to produce such an image is "u-boot.kwb". For example:
- export BUILD_DIR=/tmp/build
- make distclean
- make yourboard_config
- make $BUILD_DIR/u-boot.kwb
Board specific configuration file specifications:
-1. This file must present in the $(BOARDDIR) and the name should be
- kwbimage.cfg (since this is used in Makefile)
+1. This file must present in the $(BOARDDIR). The default name is
- kwbimage.cfg. The name can be set as part of the full path
to the file using CONFIG_SYS_KWD_CONFIG (probably ininclude/configs/<yourboard>.h). The path should looklike:
$(SRCTREE)/$(CONFIG_BOARDDIR)/<yourkwbimagename>.cfg
- This file can have empty lines and lines starting with "#" as
first character to put comments 3. This file can have configuration command lines as mentioned
below,
--
Acked by: Prafulla Wadaskar prafulla@marvell.com
I will pull this patch latter.
Applied to u-boot-marvell.git master branch
Regards... Prafulla . . .
participants (2)
-
Karl O. Pinc -
Prafulla Wadaskar