From: Mingkai Hu Mingkai.Hu@freescale.com

C29XPCIE board is a series of Freescale PCIe add-in cards to perform as public key crypto accelerator or secure key management module. It includes C293PCIE board, C293PCIE board and C291PCIE board.

- 512KB platform SRAM in addition to 512K L2 Cache/SRAM - 512MB soldered DDR3 32bit memory - CPLD System Logic - 64MB x16 NOR flash and 4GB x8 NAND flash - 16MB SPI flash

Signed-off-by: Mingkai Hu Mingkai.Hu@freescale.com Singed-off-by: Po Liu Po.Liu@freescale.com --- Changes for v2: - Remove define CONFIG_C291/CONFIG_C292/CONFIG_C293, replace with CONFIG_C29X - Adjust the TLB config mode - Add SEC node removal method by check the CPU SVR - Clean up the C29XPCIE.h file Changes for v3: - Replace CONFIG_C29X with CONFIG_PPC_C29X Changes for v4: - Clean up comments in tlb.c - Change NAND flash TLB and LAW size to 16KB - Modify flash tlb mode in c29xpcie.c - Change cpld.h and cpld.c code for read/write cpld register - Continue clean up the C29XPCIE.h file Changes for v5: - Add C29XPCIE board to MAINTAINERS - Clean up the C29XPCIE.h file a. Remove #undef CONFIG_SYS_RAMBOOT b. Remove #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " c. Modify CONFIG_BOOTDELAY to -1 - Remove 0xfffff000 LAW in tlb.c

MAINTAINERS | 4 + board/freescale/c29xpcie/Makefile | 34 +++ board/freescale/c29xpcie/c29xpcie.c | 151 ++++++++++++ board/freescale/c29xpcie/cpld.c | 134 ++++++++++ board/freescale/c29xpcie/cpld.h | 43 ++++ board/freescale/c29xpcie/ddr.c | 89 +++++++ board/freescale/c29xpcie/law.c | 22 ++ board/freescale/c29xpcie/tlb.c | 79 ++++++ boards.cfg | 2 + include/configs/C29XPCIE.h | 472 ++++++++++++++++++++++++++++++++++++ 10 files changed, 1030 insertions(+) create mode 100644 board/freescale/c29xpcie/Makefile create mode 100644 board/freescale/c29xpcie/c29xpcie.c create mode 100644 board/freescale/c29xpcie/cpld.c create mode 100644 board/freescale/c29xpcie/cpld.h create mode 100644 board/freescale/c29xpcie/ddr.c create mode 100644 board/freescale/c29xpcie/law.c create mode 100644 board/freescale/c29xpcie/tlb.c create mode 100644 include/configs/C29XPCIE.h

diff --git a/MAINTAINERS b/MAINTAINERS index 7820375..26fc123 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -538,6 +538,10 @@ Detlev Zundel dzu@denx.de

inka4x0 MPC5200

+Po Liu po.liu@freescale.com + + C29XPCIE C29X + -------------------------------------------------------------------------

Unknown / orphaned boards: diff --git a/board/freescale/c29xpcie/Makefile b/board/freescale/c29xpcie/Makefile new file mode 100644 index 0000000..15bef9a --- /dev/null +++ b/board/freescale/c29xpcie/Makefile @@ -0,0 +1,34 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += cpld.o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/c29xpcie/c29xpcie.c b/board/freescale/c29xpcie/c29xpcie.c new file mode 100644 index 0000000..acc59d2 --- /dev/null +++ b/board/freescale/c29xpcie/c29xpcie.c @@ -0,0 +1,151 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/io.h> +#include <miiphy.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <fsl_mdio.h> +#include <tsec.h> +#include <mmc.h> +#include <netdev.h> +#include <pci.h> +#include <asm/fsl_ifc.h> +#include <asm/fsl_pci.h> + +#include "cpld.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + struct cpu_type *cpu = gd->arch.cpu; + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + printf("Board: %sPCIe, ", cpu->name); + printf("CPLD Ver: 0x%02x\n", in_8(&cpld_data->cpldver)); + + return 0; +} + +int board_early_init_f(void) +{ + struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR; + + /* Clock configuration to access CPLD using IFC(GPCM) */ + setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); + + return 0; +} + +int board_early_init_r(void) +{ + const unsigned long flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_64M, 1); + + return 0; +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} +#endif /* ifdef CONFIG_PCI */ + +#ifdef CONFIG_TSEC_ENET +int board_eth_init(bd_t *bis) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[2]; + int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + num++; +#endif + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + /* Register 1G MDIO bus */ + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, num); + + return pci_eth_init(bis); +} +#endif + +#if defined(CONFIG_OF_BOARD_SETUP) +void fdt_del_sec(void *blob, int offset) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compat_reg(blob, "fsl,sec-v6.0", + CONFIG_SYS_CCSRBAR_PHYS + CONFIG_SYS_FSL_SEC_OFFSET + + offset * 0x20000)) >= 0) { + fdt_del_node(blob, nodeoff); + offset++; + } +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + struct cpu_type *cpu; + + cpu = gd->arch.cpu; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + +#if defined(CONFIG_PCI) + FT_FSL_PCI_SETUP; +#endif + + fdt_fixup_memory(blob, (u64)base, (u64)size); + if (cpu->soc_ver == SVR_C291) + fdt_del_sec(blob, 1); + else if (cpu->soc_ver == SVR_C292) + fdt_del_sec(blob, 2); +} +#endif diff --git a/board/freescale/c29xpcie/cpld.c b/board/freescale/c29xpcie/cpld.c new file mode 100644 index 0000000..b17a7ba --- /dev/null +++ b/board/freescale/c29xpcie/cpld.c @@ -0,0 +1,134 @@ +/** + * Copyright 2013 Freescale Semiconductor + * Author: Mingkai Hu Mingkai.hu@freescale.com + * Po Liu Po.Liu@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This file provides support for the board-specific CPLD used on some Freescale + * reference boards. + * + * The following macros need to be defined: + * + * CONFIG_SYS_CPLD_BASE - The virtual address of the base of the + * CPLD register map + * + */ + +#include <common.h> +#include <command.h> +#include <asm/io.h> + +#include "cpld.h" +/** + * Set the boot bank to the alternate bank + */ +void cpld_set_altbank(u8 banksel) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + u8 reg11; + + reg11 = in_8(&cpld_data->flhcsr); + + switch (banksel) { + case 1: + out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK) + | CPLD_BANKSEL_EN | CPLD_SELECT_BANK1); + break; + case 2: + out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK) + | CPLD_BANKSEL_EN | CPLD_SELECT_BANK2); + break; + case 3: + out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK) + | CPLD_BANKSEL_EN | CPLD_SELECT_BANK3); + break; + case 4: + out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK) + | CPLD_BANKSEL_EN | CPLD_SELECT_BANK4); + break; + default: + printf("Invalid value! [1-4]\n"); + return; + } + + udelay(100); + do_reset(NULL, 0, 0, NULL); +} + +/** + * Set the boot bank to the default bank + */ +void cpld_set_defbank(void) +{ + cpld_set_altbank(4); +} + +#ifdef DEBUG +static void cpld_dump_regs(void) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + printf("chipid1 = 0x%02x\n", in_8(&cpld_data->chipid1)); + printf("chipid2 = 0x%02x\n", in_8(&cpld_data->chipid2)); + printf("hwver = 0x%02x\n", in_8(&cpld_data->hwver)); + printf("cpldver = 0x%02x\n", in_8(&cpld_data->cpldver)); + printf("rstcon = 0x%02x\n", in_8(&cpld_data->rstcon)); + printf("flhcsr = 0x%02x\n", in_8(&cpld_data->flhcsr)); + printf("wdcsr = 0x%02x\n", in_8(&cpld_data->wdcsr)); + printf("wdkick = 0x%02x\n", in_8(&cpld_data->wdkick)); + printf("fancsr = 0x%02x\n", in_8(&cpld_data->fancsr)); + printf("ledcsr = 0x%02x\n", in_8(&cpld_data->ledcsr)); + printf("misc = 0x%02x\n", in_8(&cpld_data->misccsr)); + printf("bootor = 0x%02x\n", in_8(&cpld_data->bootor)); + printf("bootcfg1 = 0x%02x\n", in_8(&cpld_data->bootcfg1)); + printf("bootcfg2 = 0x%02x\n", in_8(&cpld_data->bootcfg2)); + printf("bootcfg3 = 0x%02x\n", in_8(&cpld_data->bootcfg3)); + printf("bootcfg4 = 0x%02x\n", in_8(&cpld_data->bootcfg4)); + putc('\n'); +} +#endif + +int cpld_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int rc = 0; + unsigned char value; + + if (argc <= 1) + return cmd_usage(cmdtp); + + if (strcmp(argv[1], "reset") == 0) { + if (!strcmp(argv[2], "altbank") && argv[3]) { + value = (u8)simple_strtoul(argv[3], NULL, 16); + cpld_set_altbank(value); + } else if (!argv[2]) + cpld_set_defbank(); + else + cmd_usage(cmdtp); +#ifdef DEBUG + } else if (strcmp(argv[1], "dump") == 0) { + cpld_dump_regs(); +#endif + } else + rc = cmd_usage(cmdtp); + + return rc; +} + +U_BOOT_CMD( + cpld_cmd, CONFIG_SYS_MAXARGS, 1, cpld_cmd, + "Reset the board using the CPLD sequencer", + "reset - hard reset to default bank 4\n" + "cpld_cmd reset altbank [bank]- reset to alternate bank\n" + " - [bank] bank value select 1-4\n" + " - bank 1 on the flash 0x0000000~0x0ffffff\n" + " - bank 2 on the flash 0x1000000~0x1ffffff\n" + " - bank 3 on the flash 0x2000000~0x2ffffff\n" + " - bank 4 on the flash 0x3000000~0x3ffffff\n" +#ifdef DEBUG + "cpld_cmd dump - display the CPLD registers\n" +#endif + ); diff --git a/board/freescale/c29xpcie/cpld.h b/board/freescale/c29xpcie/cpld.h new file mode 100644 index 0000000..24093c4 --- /dev/null +++ b/board/freescale/c29xpcie/cpld.h @@ -0,0 +1,43 @@ +/** + * Copyright 2013 Freescale Semiconductor + * Author: Mingkai Hu Mingkai.Hu@freescale.com + * Po Liu Po.Liu@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This file provides support for the ngPIXIS, a board-specific FPGA used on + * some Freescale reference boards. + */ + +/* + * CPLD register set. Feel free to add board-specific #ifdefs where necessary. + */ +struct cpld_data { + u8 chipid1; /* 0x0 - CPLD Chip ID1 Register */ + u8 chipid2; /* 0x1 - CPLD Chip ID2 Register */ + u8 hwver; /* 0x2 - Hardware Version Register */ + u8 cpldver; /* 0x3 - Software Version Register */ + u8 res[12]; + u8 rstcon; /* 0x10 - Reset control register */ + u8 flhcsr; /* 0x11 - Flash control and status Register */ + u8 wdcsr; /* 0x12 - Watchdog control and status Register */ + u8 wdkick; /* 0x13 - Watchdog kick Register */ + u8 fancsr; /* 0x14 - Fan control and status Register */ + u8 ledcsr; /* 0x15 - LED control and status Register */ + u8 misccsr; /* 0x16 - Misc control and status Register */ + u8 bootor; /* 0x17 - Boot configure override Register */ + u8 bootcfg1; /* 0x18 - Boot configure 1 Register */ + u8 bootcfg2; /* 0x19 - Boot configure 2 Register */ + u8 bootcfg3; /* 0x1a - Boot configure 3 Register */ + u8 bootcfg4; /* 0x1b - Boot configure 4 Register */ +}; + +#define CPLD_BANKSEL_EN 0x02 +#define CPLD_BANKSEL_MASK 0x3f +#define CPLD_SELECT_BANK1 0xc0 +#define CPLD_SELECT_BANK2 0x80 +#define CPLD_SELECT_BANK3 0x40 +#define CPLD_SELECT_BANK4 0x00 diff --git a/board/freescale/c29xpcie/ddr.c b/board/freescale/c29xpcie/ddr.c new file mode 100644 index 0000000..62476ca --- /dev/null +++ b/board/freescale/c29xpcie/ddr.c @@ -0,0 +1,89 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +/* + * Micron MT41J128M16HA-15E + * */ +dimm_params_t ddr_raw_timing = { + .n_ranks = 1, + .rank_density = 536870912u, + .capacity = 536870912u, + .primary_sdram_width = 32, + .ec_sdram_width = 8, + .registered_dimm = 0, + .mirrored_dimm = 0, + .n_row_addr = 14, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 2, + .burst_lengths_bitmask = 0x0c, + + .tCKmin_X_ps = 1650, + .caslat_X = 0x7e << 4, /* 5,6,7,8,9,10 */ + .tAA_ps = 14050, + .tWR_ps = 15000, + .tRCD_ps = 13500, + .tRRD_ps = 75000, + .tRP_ps = 13500, + .tRAS_ps = 40000, + .tRC_ps = 49500, + .tRFC_ps = 160000, + .tWTR_ps = 75000, + .tRTP_ps = 75000, + .refresh_rate_ps = 7800000, + .tFAW_ps = 30000, +}; + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "Fixed DDR on board"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + int i; + popts->clk_adjust = 2; + popts->cpo_override = 0x1f; + popts->write_data_delay = 4; + popts->half_strength_driver_enable = 1; + popts->bstopre = 0x3cf; + popts->quad_rank_present = 1; + popts->rtt_override = 1; + popts->rtt_override_value = 1; + popts->dynamic_power = 1; + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x4; + popts->trwt_override = 1; + popts->trwt = 0; + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; + popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; + } +} diff --git a/board/freescale/c29xpcie/law.c b/board/freescale/c29xpcie/law.c new file mode 100644 index 0000000..10a2fbf --- /dev/null +++ b/board/freescale/c29xpcie/law.c @@ -0,0 +1,22 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_16K, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS, LAW_SIZE_512K, + LAW_TRGT_IF_PLATFORM_SRAM), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/c29xpcie/tlb.c b/board/freescale/c29xpcie/tlb.c new file mode 100644 index 0000000..a175906 --- /dev/null +++ b/board/freescale/c29xpcie/tlb.c @@ -0,0 +1,79 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 1, BOOKE_PAGESZ_64M, 1), + +#ifdef CONFIG_PCI + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_256K, 1), +#endif + + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_4K, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_16K, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PLATFORM_SRAM_BASE, + CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 6, BOOKE_PAGESZ_256K, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_PLATFORM_SRAM_BASE + 0x40000, + CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS + 0x40000, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_256K, 1), + +#ifdef CONFIG_SYS_RAMBOOT + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, + CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 8, BOOKE_PAGESZ_256M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, + CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 9, BOOKE_PAGESZ_256M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index c0c4282..4c68e9f 100644 --- a/boards.cfg +++ b/boards.cfg @@ -771,6 +771,8 @@ MPC8569MDS_NAND powerpc mpc85xx mpc8569mds freesca MPC8572DS powerpc mpc85xx mpc8572ds freescale - MPC8572DS MPC8572DS_36BIT powerpc mpc85xx mpc8572ds freescale - MPC8572DS:36BIT MPC8572DS_NAND powerpc mpc85xx mpc8572ds freescale - MPC8572DS:NAND +C29XPCIE powerpc mpc85xx c29xpcie freescale - C29XPCIE:C29XPCIE,36BIT +C29XPCIE_SPIFLASH powerpc mpc85xx c29xpcie freescale - C29XPCIE:C29XPCIE,36BIT,SPIFLASH P1010RDB_36BIT_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,NAND P1010RDB_36BIT_NAND_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,NAND_SECBOOT,SECURE_BOOT P1010RDB_36BIT_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h new file mode 100644 index 0000000..02f4fdf --- /dev/null +++ b/include/configs/C29XPCIE.h @@ -0,0 +1,472 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * C29XPCIE board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_PHYS_64BIT + +#ifdef CONFIG_C29XPCIE +#define CONFIG_PPC_C29X +#endif + +#ifdef CONFIG_SPIFLASH +#define CONFIG_RAMBOOT_SPIFLASH +#define CONFIG_SYS_TEXT_BASE 0x11000000 +#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc +#endif + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */ + +#define CONFIG_PCI /* Enable PCI/PCIE */ +#ifdef CONFIG_PCI +#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI + +#define CONFIG_E1000 + +/* + * PCI Windows + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +/* controller 1, Slot 1, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_NAME "Slot 1" +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif + +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_TSEC_ENET +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_DDR_CLK_FREQ 100000000 +#define CONFIG_SYS_CLK_FREQ 66666666 + +#define CONFIG_HWCONFIG + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP 1 +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_PANIC_HANG + +/* DDR Setup */ +#define CONFIG_FSL_DDR3 +#define CONFIG_DDR_SPD +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x50 +#define CONFIG_SYS_DDR_RAW_TIMING + +/* DDR ECC Setup*/ +#define CONFIG_DDR_ECC +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER + +#define CONFIG_SYS_SDRAM_SIZE 512 +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 + +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* Platform SRAM setting */ +#define CONFIG_SYS_PLATFORM_SRAM_BASE 0xffb00000 +#define CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS \ + (0xf00000000ull | CONFIG_SYS_PLATFORM_SRAM_BASE) +#define CONFIG_SYS_PLATFORM_SRAM_SIZE (512 << 10) + +/* + * IFC Definitions + */ +/* NOR Flash on IFC */ +#define CONFIG_SYS_FLASH_BASE 0xec000000 +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ + +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) + +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } +#define CONFIG_SYS_MAX_FLASH_BANKS 1 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* in ms */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* in ms */ + +/* 16Bit NOR Flash - S29GL512S10TFI01 */ +#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(64*1024*1024) +#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1e) | \ + FTIM1_NOR_TRAD_NOR(0x0f) | \ + FTIM1_NOR_TSEQRAD_NOR(0x0f)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +/* CFI for NOR Flash */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +/* NAND Flash on IFC */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* 8Bit NAND Flash - K9F1G08U0B */ +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_NAND \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_2 /* RAL = 2 Bytes */ \ + | CSOR_NAND_PGS_2K /* Page Size = 2k */ \ + | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \ + | CSOR_NAND_PB(64)) /* 64 Pages Per Block */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x01) | \ + FTIM0_NAND_TWP(0x0c) | \ + FTIM0_NAND_TWCHT(0x08) | \ + FTIM0_NAND_TWH(0x06)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x28) | \ + FTIM1_NAND_TWBE(0x1d) | \ + FTIM1_NAND_TRR(0x08) | \ + FTIM1_NAND_TRP(0x0c)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0c) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x18)) +#define CONFIG_SYS_NAND_FTIM3 (FTIM3_NAND_TWW(0x04)) + +#define CONFIG_SYS_NAND_DDR_LAW 11 + +/* Set up IFC registers for boot location NOR/NAND */ +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 + +/* CPLD on IFC, selected by CS2 */ +#define CONFIG_SYS_CPLD_BASE 0xffdf0000 +#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull \ + | CONFIG_SYS_CPLD_BASE) + +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) +#define CONFIG_SYS_CSOR2 0x0 +/* CPLD Timing parameters for IFC CS2 */ +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS2_FTIM3 0x0 + +#if defined(CONFIG_RAMBOOT_SPIFLASH) +#define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC +#endif + +#define CONFIG_BOARD_EARLY_INIT_R + +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 +#define CONFIG_SYS_INIT_RAM_END 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \ + - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* I2C EEPROM */ +/* enable read and write access to EEPROM */ +#define CONFIG_CMD_EEPROM +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +#define CONFIG_CMD_I2C + +/* eSPI - Enhanced SPI */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_EON +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 + +#ifdef CONFIG_TSEC_ENET +#define CONFIG_NET_MULTI +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" + +/* Default mode is RGMII mode */ +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 2 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#if defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_RAMBOOT_SPIFLASH) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#endif +#else +#define CONFIG_ENV_IS_IN_FLASH +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 +#define CONFIG_ENV_ADDR 0xfff80000 +#else +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#endif +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 +#endif + +#define CONFIG_LOADS_ECHO +#define CONFIG_SYS_LOADS_BAUD_CHANGE + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* dec freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +/* + * Environment Configuration + */ + +#ifdef CONFIG_TSEC_ENET +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#endif + +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=" __stringify(CONFIG_DEF_HWCONFIG) "\0" \ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "loadaddr=1000000\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=rootfs.ext2.gz.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=name/of/device-tree.dtb\0" \ + "othbootargs=ramdisk_size=600000\0" \ + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs; " \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND + +#endif /* __CONFIG_H */