From: Patrice Chotard patrice.chotard@st.com

reset-names property is needed to use the reset API for STi sdhci driver.

Signed-off-by: Patrice Chotard patrice.chotard@st.com Reviewed-by: Jaehoon Chung jh80.chung@samsung.com --- v4: _ none

v3: _ none

v2: _ none

arch/arm/dts/stih407-family.dtsi | 1 + 1 file changed, 1 insertion(+)

diff --git a/arch/arm/dts/stih407-family.dtsi b/arch/arm/dts/stih407-family.dtsi index af66b53..452ac1c 100644 --- a/arch/arm/dts/stih407-family.dtsi +++ b/arch/arm/dts/stih407-family.dtsi @@ -563,6 +563,7 @@ clocks = <&clk_s_c0_flexgen CLK_MMC_1>, <&clk_s_c0_flexgen CLK_RX_ICN_HVA>; resets = <&softreset STIH407_MMC1_SOFTRESET>; + reset-names = "softreset"; bus-width = <4>; };

From: Patrice Chotard patrice.chotard@st.com

This is the generic phy driver for the picoPHY ports used by USB2/1.1 controllers. It is found on STiH407 SoC family from STMicroelectronics.

Signed-off-by: Patrice Chotard patrice.chotard@st.com ---

v4: _ update to use the new PHY uclass currently available on dm-next branch

v3: _ convert driver to USB PHY uclass

v2: _ replace bitfield_replace() by clrsetbits_le32()

doc/device-tree-bindings/phy/phy-stih407-usb.txt | 24 +++ drivers/phy/Kconfig | 8 + drivers/phy/Makefile | 1 + drivers/phy/sti_usb_phy.c | 181 +++++++++++++++++++++++ 4 files changed, 214 insertions(+) create mode 100644 doc/device-tree-bindings/phy/phy-stih407-usb.txt create mode 100644 drivers/phy/sti_usb_phy.c

diff --git a/doc/device-tree-bindings/phy/phy-stih407-usb.txt b/doc/device-tree-bindings/phy/phy-stih407-usb.txt new file mode 100644 index 0000000..de6a706 --- /dev/null +++ b/doc/device-tree-bindings/phy/phy-stih407-usb.txt @@ -0,0 +1,24 @@ +ST STiH407 USB PHY controller + +This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3 +host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics. + +Required properties: +- compatible : should be "st,stih407-usb2-phy" +- st,syscfg : phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets +- resets : list of phandle and reset specifier pairs. There should be two entries, one + for the whole phy and one for the port +- reset-names : list of reset signal names. Should be "global" and "port" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + +usb2_picophy0: usbpicophy@f8 { + compatible = "st,stih407-usb2-phy"; + #phy-cells = <0>; + st,syscfg = <&syscfg_core 0x100 0xf4>; + resets = <&softreset STIH407_PICOPHY_SOFTRESET>, + <&picophyreset STIH407_PICOPHY0_RESET>; + reset-names = "global", "port"; +}; diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index a91a694..4330b36 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -59,4 +59,12 @@ config SPL_PIPE3_PHY This PHY is found on omap devices supporting SATA such as dra7, am57x and omap5

+config STI_USB_PHY + bool "STMicroelectronics USB2 picoPHY driver for STiH407 family" + depends on PHY && ARCH_STI + help + This is the generic phy driver for the picoPHY ports + used by USB2 and USB3 Host controllers available on + STiH407 SoC families. + endmenu diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index 6ce96d2..22d92d3 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -8,3 +8,4 @@ obj-$(CONFIG_$(SPL_)PHY) += phy-uclass.o obj-$(CONFIG_PHY_SANDBOX) += sandbox-phy.o obj-$(CONFIG_$(SPL_)PIPE3_PHY) += ti-pipe3-phy.o +obj-$(CONFIG_STI_USB_PHY) += sti_usb_phy.o diff --git a/drivers/phy/sti_usb_phy.c b/drivers/phy/sti_usb_phy.c new file mode 100644 index 0000000..c164062 --- /dev/null +++ b/drivers/phy/sti_usb_phy.c @@ -0,0 +1,181 @@ +/* + * Copyright (c) 2017 + * Patrice Chotard patrice.chotard@st.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <bitfield.h> +#include <dm.h> +#include <errno.h> +#include <fdtdec.h> +#include <generic-phy.h> +#include <libfdt.h> +#include <regmap.h> +#include <reset-uclass.h> +#include <syscon.h> +#include <wait_bit.h> + +#include <linux/bitops.h> +#include <linux/compat.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* Default PHY_SEL and REFCLKSEL configuration */ +#define STIH407_USB_PICOPHY_CTRL_PORT_CONF 0x6 + +/* ports parameters overriding */ +#define STIH407_USB_PICOPHY_PARAM_DEF 0x39a4dc + +#define PHYPARAM_REG 1 +#define PHYCTRL_REG 2 +#define PHYPARAM_NB 3 + +struct sti_usb_phy { + struct regmap *regmap; + struct reset_ctl global_ctl; + struct reset_ctl port_ctl; + int param; + int ctrl; +}; + +static int sti_usb_phy_deassert(struct sti_usb_phy *phy) +{ + int ret; + + ret = reset_deassert(&phy->global_ctl); + if (ret < 0) { + error("PHY global deassert failed: %d", ret); + return ret; + } + + ret = reset_deassert(&phy->port_ctl); + if (ret < 0) + error("PHY port deassert failed: %d", ret); + + return ret; +} + +static int sti_usb_phy_init(struct phy *usb_phy) +{ + struct udevice *dev = usb_phy->dev; + struct sti_usb_phy *phy = dev_get_priv(dev); + void __iomem *reg; + + /* set ctrl picophy value */ + reg = (void __iomem *)phy->regmap->base + phy->ctrl; + /* CTRL_PORT mask is 0x1f */ + clrsetbits_le32(reg, 0x1f, STIH407_USB_PICOPHY_CTRL_PORT_CONF); + + /* set ports parameters overriding */ + reg = (void __iomem *)phy->regmap->base + phy->param; + /* PARAM_DEF mask is 0xffffffff */ + clrsetbits_le32(reg, 0xffffffff, STIH407_USB_PICOPHY_PARAM_DEF); + + return sti_usb_phy_deassert(phy); +} + +static int sti_usb_phy_exit(struct phy *usb_phy) +{ + struct udevice *dev = usb_phy->dev; + struct sti_usb_phy *phy = dev_get_priv(dev); + int ret; + + ret = reset_deassert(&phy->port_ctl); + if (ret < 0) { + error("PHY port deassert failed: %d", ret); + return ret; + } + + ret = reset_deassert(&phy->global_ctl); + if (ret < 0) + error("PHY global deassert failed: %d", ret); + + return ret; +} + +struct phy_ops sti_usb_phy_ops = { + .init = sti_usb_phy_init, + .exit = sti_usb_phy_exit, +}; + +int sti_usb_phy_probe(struct udevice *dev) +{ + struct sti_usb_phy *priv = dev_get_priv(dev); + struct udevice *syscon; + struct fdtdec_phandle_args syscfg_phandle; + u32 cells[PHYPARAM_NB]; + int ret, count; + + /* get corresponding syscon phandle */ + ret = fdtdec_parse_phandle_with_args(gd->fdt_blob, dev->of_offset, + "st,syscfg", NULL, 0, 0, + &syscfg_phandle); + if (ret < 0) { + error("Can't get syscfg phandle: %d\n", ret); + return ret; + } + + ret = uclass_get_device_by_of_offset(UCLASS_SYSCON, syscfg_phandle.node, + &syscon); + if (ret) { + error("unable to find syscon device (%d)\n", ret); + return ret; + } + + priv->regmap = syscon_get_regmap(syscon); + if (!priv->regmap) { + error("unable to find regmap\n"); + return -ENODEV; + } + + /* get phy param offset */ + count = fdtdec_get_int_array_count(gd->fdt_blob, dev->of_offset, + "st,syscfg", cells, + ARRAY_SIZE(cells)); + + if (count < 0) { + error("Bad PHY st,syscfg property %d\n", count); + return -EINVAL; + } + + if (count > PHYPARAM_NB) { + error("Unsupported PHY param count %d\n", count); + return -EINVAL; + } + + priv->param = cells[PHYPARAM_REG]; + priv->ctrl = cells[PHYCTRL_REG]; + + /* get global reset control */ + ret = reset_get_by_name(dev, "global", &priv->global_ctl); + if (ret) { + error("can't get global reset for %s (%d)", dev->name, ret); + return ret; + } + + /* get port reset control */ + ret = reset_get_by_name(dev, "port", &priv->port_ctl); + if (ret) { + error("can't get port reset for %s (%d)", dev->name, ret); + return ret; + } + + return 0; +} + +static const struct udevice_id sti_usb_phy_ids[] = { + { .compatible = "st,stih407-usb2-phy" }, + { } +}; + +U_BOOT_DRIVER(sti_usb_phy) = { + .name = "sti_usb_phy", + .id = UCLASS_PHY, + .of_match = sti_usb_phy_ids, + .probe = sti_usb_phy_probe, + .ops = &sti_usb_phy_ops, + .priv_auto_alloc_size = sizeof(struct sti_usb_phy), +};

From: Patrice Chotard patrice.chotard@st.com

Add support for on-chip ohci controller available on STMicrolectronics SoCs. Ohci support will be then available on both type A USB 2.0 connectors.

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- v4: _ update to use the new PHY uclass currently available on dm-next branch

v3: _ update to use new USB PHY uclass

v2: _ put board specific defines in a separate patch

drivers/usb/host/Kconfig | 9 ++++ drivers/usb/host/Makefile | 1 + drivers/usb/host/ohci-sti.c | 119 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 129 insertions(+) create mode 100644 drivers/usb/host/ohci-sti.c

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 7c29bf5..b259a05 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -169,6 +169,15 @@ config USB_OHCI_GENERIC ---help--- Enables support for generic OHCI controller.

+config USB_OHCI_STI + bool "Support for STMicroelectronics OHCI USB controller" + depends on ARCH_STI + depends on OF_CONTROL + depends on DM_USB + select USB_HOST + ---help--- + Enables support for the on-chip OHCI controller on STMicroelectronics SoCs. + endif # USB_OHCI_HCD

config USB_UHCI_HCD diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 303aa32..b78e632 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -22,6 +22,7 @@ obj-$(CONFIG_USB_OHCI_EP93XX) += ohci-ep93xx.o obj-$(CONFIG_USB_OHCI_SUNXI) += ohci-sunxi.o obj-$(CONFIG_USB_OHCI_LPC32XX) += ohci-lpc32xx.o obj-$(CONFIG_USB_OHCI_GENERIC) += ohci-generic.o +obj-$(CONFIG_USB_OHCI_STI) += ohci-sti.o

# echi obj-$(CONFIG_USB_EHCI) += ehci-hcd.o diff --git a/drivers/usb/host/ohci-sti.c b/drivers/usb/host/ohci-sti.c new file mode 100644 index 0000000..77f8447 --- /dev/null +++ b/drivers/usb/host/ohci-sti.c @@ -0,0 +1,119 @@ +/* + * Copyright (c) 2017 + * Patrice Chotard patrice.chotard@st.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <dm.h> +#include <errno.h> +#include <generic-phy.h> +#include "ohci.h" +#include <reset-uclass.h> +#include <usb.h> + +DECLARE_GLOBAL_DATA_PTR; + +#if !defined(CONFIG_USB_OHCI_NEW) +# error "Generic OHCI driver requires CONFIG_USB_OHCI_NEW" +#endif + +struct sti_ohci_priv { + ohci_t ohci; + struct reset_ctl power_ctl; + struct reset_ctl softreset_ctl; + struct phy usb_phy; +}; + +static int ohci_usb_probe(struct udevice *dev) +{ + struct sti_ohci_priv *priv = dev_get_priv(dev); + struct ohci_regs *regs; + int ret; + + regs = (struct ohci_regs *)dev_get_addr(dev); + if (regs == (void *)FDT_ADDR_T_NONE) + return -EINVAL; + + ret = reset_get_by_name(dev, "power", &priv->power_ctl); + if (ret) { + error("can't get power reset for %s (%d)", dev->name, ret); + return ret; + } + + ret = reset_get_by_name(dev, "softreset", &priv->softreset_ctl); + if (ret) { + error("can't get USB PHY for %s (%d)", dev->name, ret); + return ret; + } + + ret = generic_phy_get_by_name(dev, "usb", &priv->usb_phy); + if (ret) { + error("can't get soft reset for %s (%d)", dev->name, ret); + return ret; + } + + ret = reset_deassert(&priv->power_ctl); + if (ret < 0) { + error("OHCI power reset deassert failed: %d", ret); + return ret; + } + + ret = reset_deassert(&priv->softreset_ctl); + if (ret < 0) { + error("OHCI soft reset deassert failed: %d", ret); + return ret; + } + + ret = generic_phy_init(&priv->usb_phy); + if (ret) { + error("Can't init USB PHY\n"); + return ret; + } + + return ohci_register(dev, regs); +} + +static int ohci_usb_remove(struct udevice *dev) +{ + struct sti_ohci_priv *priv = dev_get_priv(dev); + int ret; + + ret = reset_deassert(&priv->power_ctl); + if (ret < 0) { + error("OHCI power reset assert failed: %d", ret); + return ret; + } + + ret = reset_deassert(&priv->softreset_ctl); + if (ret < 0) { + error("OHCI soft reset assert failed: %d", ret); + return ret; + } + + ret = generic_phy_exit(&priv->usb_phy); + if (ret) { + error("Can't deinit USB PHY\n"); + return ret; + } + + return ohci_deregister(dev); +} + +static const struct udevice_id sti_usb_ids[] = { + { .compatible = "st,st-ohci-300x" }, + { } +}; + +U_BOOT_DRIVER(ohci_sti) = { + .name = "ohci_sti", + .id = UCLASS_USB, + .of_match = sti_usb_ids, + .probe = ohci_usb_probe, + .remove = ohci_usb_remove, + .ops = &ohci_usb_ops, + .priv_auto_alloc_size = sizeof(struct sti_ohci_priv), + .flags = DM_FLAG_ALLOC_PRIV_DMA, +};

From: Patrice Chotard patrice.chotard@st.com

This patch adds the ST glue logic to manage the DWC3 HC on STiH407 SoC family. It configures the internal glue logic and syscfg registers.

Part of this code been extracted from kernel.org driver (drivers/usb/dwc3/dwc3-st.c)

Signed-off-by: Patrice Chotard patrice.chotard@st.com --- v4: _ none

v3: _ rename dwc3-sti.c to dwc3-sti-glue.c _ respect device tree hierarchy, this driver is now responsible for xhci-sti binding (done in sti_dwc3_glue_bind())

v2: _ use setbits_le32() instead of read, modify, write sequence _ add missing parenthesis

arch/arm/include/asm/arch-stih410/sys_proto.h | 11 + doc/device-tree-bindings/usb/dwc3-st.txt | 60 ++++++ drivers/usb/host/Makefile | 2 +- drivers/usb/host/dwc3-sti-glue.c | 278 ++++++++++++++++++++++++++ include/dwc3-sti-glue.h | 43 ++++ 5 files changed, 393 insertions(+), 1 deletion(-) create mode 100644 arch/arm/include/asm/arch-stih410/sys_proto.h create mode 100644 doc/device-tree-bindings/usb/dwc3-st.txt create mode 100644 drivers/usb/host/dwc3-sti-glue.c create mode 100644 include/dwc3-sti-glue.h

diff --git a/arch/arm/include/asm/arch-stih410/sys_proto.h b/arch/arm/include/asm/arch-stih410/sys_proto.h new file mode 100644 index 0000000..5c40d3b --- /dev/null +++ b/arch/arm/include/asm/arch-stih410/sys_proto.h @@ -0,0 +1,11 @@ +/* + * Copyright (c) 2017 + * Patrice Chotard patrice.chotard@st.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _ASM_ARCH_SYS_PROTO_H +#define _ASM_ARCH_SYS_PROTO_H + +#endif /* _ASM_ARCH_SYS_PROTO_H */ diff --git a/doc/device-tree-bindings/usb/dwc3-st.txt b/doc/device-tree-bindings/usb/dwc3-st.txt new file mode 100644 index 0000000..a26a139 --- /dev/null +++ b/doc/device-tree-bindings/usb/dwc3-st.txt @@ -0,0 +1,60 @@ +ST DWC3 glue logic + +This file documents the parameters for the dwc3-st driver. +This driver controls the glue logic used to configure the dwc3 core on +STiH407 based platforms. + +Required properties: + - compatible : must be "st,stih407-dwc3" + - reg : glue logic base address and USB syscfg ctrl register offset + - reg-names : should be "reg-glue" and "syscfg-reg" + - st,syscon : should be phandle to system configuration node which + encompasses the glue registers + - resets : list of phandle and reset specifier pairs. There should be two entries, one + for the powerdown and softreset lines of the usb3 IP + - reset-names : list of reset signal names. Names should be "powerdown" and "softreset" + + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property + + - pinctl-names : A pinctrl state named "default" must be defined + + - pinctrl-0 : Pin control group + + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + +Sub-nodes: +The dwc3 core should be added as subnode to ST DWC3 glue as shown in the +example below. + +NB: The dr_mode property is NOT optional for this driver, as the default value +is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are +either "host" or "device". + +Example: + +st_dwc3: dwc3@8f94000 { + status = "disabled"; + compatible = "st,stih407-dwc3"; + reg = <0x08f94000 0x1000>, <0x110 0x4>; + reg-names = "reg-glue", "syscfg-reg"; + st,syscfg = <&syscfg_core>; + resets = <&powerdown STIH407_USB3_POWERDOWN>, + <&softreset STIH407_MIPHY2_SOFTRESET>; + reset-names = "powerdown", "softreset"; + #address-cells = <1>; + #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb3>; + ranges; + + dwc3: dwc3@9900000 { + compatible = "snps,dwc3"; + reg = <0x09900000 0x100000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; + dr_mode = "host"; + phy-names = "usb2-phy", "usb3-phy"; + phys = <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>; + }; +}; diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 40ff830..6be40b8 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -66,7 +66,7 @@ obj-$(CONFIG_USB_XHCI_FSL) += xhci-fsl.o obj-$(CONFIG_USB_XHCI_MVEBU) += xhci-mvebu.o obj-$(CONFIG_USB_XHCI_OMAP) += xhci-omap.o obj-$(CONFIG_USB_XHCI_PCI) += xhci-pci.o -obj-$(CONFIG_USB_XHCI_STI) += xhci-sti.o +obj-$(CONFIG_USB_XHCI_STI) += xhci-sti.o dwc3-sti-glue.o

# designware obj-$(CONFIG_USB_DWC2) += dwc2.o diff --git a/drivers/usb/host/dwc3-sti-glue.c b/drivers/usb/host/dwc3-sti-glue.c new file mode 100644 index 0000000..368d7ef --- /dev/null +++ b/drivers/usb/host/dwc3-sti-glue.c @@ -0,0 +1,278 @@ +/* + * STiH407 family DWC3 specific Glue layer + * + * Copyright (c) 2017 + * Patrice Chotard patrice.chotard@st.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <asm/io.h> +#include <common.h> +#include <dm.h> +#include <dwc3-sti-glue.h> +#include <errno.h> +#include <fdtdec.h> +#include <libfdt.h> +#include <dm/lists.h> +#include <regmap.h> +#include <reset-uclass.h> +#include <syscon.h> +#include <usb.h> + +#include <linux/usb/dwc3.h> + +DECLARE_GLOBAL_DATA_PTR; + +struct sti_dwc3_glue_platdata { + phys_addr_t syscfg_base; + phys_addr_t glue_base; + phys_addr_t syscfg_offset; + struct reset_ctl powerdown_ctl; + struct reset_ctl softreset_ctl; + enum usb_dr_mode mode; +}; + +static int sti_dwc3_glue_drd_init(struct sti_dwc3_glue_platdata *plat) +{ + unsigned long val; + + val = readl(plat->syscfg_base + plat->syscfg_offset); + + val &= USB3_CONTROL_MASK; + + switch (plat->mode) { + case USB_DR_MODE_PERIPHERAL: + val &= ~(USB3_DELAY_VBUSVALID + | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3) + | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2 + | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2); + + val |= USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID; + break; + + case USB_DR_MODE_HOST: + val &= ~(USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID + | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3) + | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2 + | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2); + + val |= USB3_DELAY_VBUSVALID; + break; + + default: + error("Unsupported mode of operation %d\n", plat->mode); + return -EINVAL; + } + return writel(val, plat->syscfg_base + plat->syscfg_offset); +} + +static void sti_dwc3_glue_init(struct sti_dwc3_glue_platdata *plat) +{ + unsigned long reg; + + reg = readl(plat->glue_base + CLKRST_CTRL); + + reg |= AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION; + reg &= ~SW_PIPEW_RESET_N; + + writel(reg, plat->glue_base + CLKRST_CTRL); + + /* configure mux for vbus, powerpresent and bvalid signals */ + reg = readl(plat->glue_base + USB2_VBUS_MNGMNT_SEL1); + + reg |= SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) | + SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) | + SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG); + + writel(reg, plat->glue_base + USB2_VBUS_MNGMNT_SEL1); + + setbits_le32(plat->glue_base + CLKRST_CTRL, SW_PIPEW_RESET_N); +} + +int sti_dwc3_init(enum usb_dr_mode mode) +{ + struct sti_dwc3_glue_platdata plat; + struct fdtdec_phandle_args syscfg_phandle; + struct udevice *syscon; + struct regmap *regmap; + int node, ret; + const void *blob = gd->fdt_blob; + u32 reg[4]; + + /* find the dwc3 node */ + node = fdt_node_offset_by_compatible(blob, -1, "st,stih407-dwc3"); + + ret = fdtdec_get_int_array(blob, node, "reg", reg, ARRAY_SIZE(reg)); + if (ret) { + error("unable to find st,stih407-dwc3 reg property(%d)\n", ret); + return ret; + } + + plat.glue_base = reg[0]; + plat.syscfg_offset = reg[2]; + plat.mode = mode; + + /* get corresponding syscon phandle */ + ret = fdtdec_parse_phandle_with_args(gd->fdt_blob, node, + "st,syscfg", NULL, 0, 0, + &syscfg_phandle); + if (ret < 0) { + error("Can't get syscfg phandle: %d\n", ret); + return ret; + } + + ret = uclass_get_device_by_of_offset(UCLASS_SYSCON, syscfg_phandle.node, + &syscon); + if (ret) { + error("unable to find syscon device (%d)\n", ret); + return ret; + } + + /* get syscfg-reg base address */ + regmap = syscon_get_regmap(syscon); + if (!regmap) { + error("unable to find regmap\n"); + return -ENODEV; + } + plat.syscfg_base = regmap->base; + + sti_dwc3_glue_drd_init(&plat); + sti_dwc3_glue_init(&plat); + + return 0; +} + +static int sti_dwc3_glue_ofdata_to_platdata(struct udevice *dev) +{ + struct sti_dwc3_glue_platdata *plat = dev_get_platdata(dev); + struct fdtdec_phandle_args syscfg_phandle; + struct udevice *syscon; + struct regmap *regmap; + int ret; + u32 reg[4]; + + ret = fdtdec_get_int_array(gd->fdt_blob, dev_of_offset(dev), + "reg", reg, ARRAY_SIZE(reg)); + if (ret) { + error("unable to find st,stih407-dwc3 reg property(%d)\n", ret); + return ret; + } + + plat->glue_base = reg[0]; + plat->syscfg_offset = reg[2]; + + /* get corresponding syscon phandle */ + ret = fdtdec_parse_phandle_with_args(gd->fdt_blob, dev_of_offset(dev), + "st,syscfg", NULL, 0, 0, + &syscfg_phandle); + if (ret < 0) { + error("Can't get syscfg phandle: %d\n", ret); + return ret; + } + + ret = uclass_get_device_by_of_offset(UCLASS_SYSCON, syscfg_phandle.node, + &syscon); + if (ret) { + error("unable to find syscon device (%d)\n", ret); + return ret; + } + + /* get syscfg-reg base address */ + regmap = syscon_get_regmap(syscon); + if (!regmap) { + error("unable to find regmap\n"); + return -ENODEV; + } + plat->syscfg_base = regmap->base; + + /* get powerdown reset */ + ret = reset_get_by_name(dev, "powerdown", &plat->powerdown_ctl); + if (ret) { + error("can't get powerdown reset for %s (%d)", dev->name, ret); + return ret; + } + + /* get softreset reset */ + ret = reset_get_by_name(dev, "softreset", &plat->softreset_ctl); + if (ret) + error("can't get soft reset for %s (%d)", dev->name, ret); + + return ret; +}; + +static int sti_dwc3_glue_bind(struct udevice *dev) +{ + int dwc3_node; + + /* check if one subnode is present */ + dwc3_node = fdt_first_subnode(gd->fdt_blob, dev_of_offset(dev)); + if (dwc3_node <= 0) { + error("Can't find subnode for %s\n", dev->name); + return -ENODEV; + } + + /* check if the subnode compatible string is the dwc3 one*/ + if (fdt_node_check_compatible(gd->fdt_blob, dwc3_node, + "snps,dwc3") != 0) { + error("Can't find dwc3 subnode for %s\n", dev->name); + return -ENODEV; + } + + return dm_scan_fdt_dev(dev); +} + +static int sti_dwc3_glue_probe(struct udevice *dev) +{ + struct sti_dwc3_glue_platdata *plat = dev_get_platdata(dev); + int ret; + + /* deassert both powerdown and softreset */ + ret = reset_deassert(&plat->powerdown_ctl); + if (ret < 0) { + error("DWC3 powerdown reset deassert failed: %d", ret); + return ret; + } + + ret = reset_deassert(&plat->softreset_ctl); + if (ret < 0) + error("DWC3 soft reset deassert failed: %d", ret); + + return ret; +} + +static int sti_dwc3_glue_remove(struct udevice *dev) +{ + struct sti_dwc3_glue_platdata *plat = dev_get_platdata(dev); + int ret; + + /* assert both powerdown and softreset */ + ret = reset_assert(&plat->powerdown_ctl); + if (ret < 0) { + error("DWC3 powerdown reset deassert failed: %d", ret); + return ret; + } + + ret = reset_assert(&plat->softreset_ctl); + if (ret < 0) + error("DWC3 soft reset deassert failed: %d", ret); + + return ret; +} + +static const struct udevice_id sti_dwc3_glue_ids[] = { + { .compatible = "st,stih407-dwc3" }, + { } +}; + +U_BOOT_DRIVER(dwc3_sti_glue) = { + .name = "dwc3_sti_glue", + .id = UCLASS_MISC, + .of_match = sti_dwc3_glue_ids, + .ofdata_to_platdata = sti_dwc3_glue_ofdata_to_platdata, + .probe = sti_dwc3_glue_probe, + .remove = sti_dwc3_glue_remove, + .bind = sti_dwc3_glue_bind, + .platdata_auto_alloc_size = sizeof(struct sti_dwc3_glue_platdata), + .flags = DM_FLAG_ALLOC_PRIV_DMA, +}; diff --git a/include/dwc3-sti-glue.h b/include/dwc3-sti-glue.h new file mode 100644 index 0000000..2083427 --- /dev/null +++ b/include/dwc3-sti-glue.h @@ -0,0 +1,43 @@ +/* + * Copyright (c) 2017 + * Patrice Chotard patrice.chotard@st.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DWC3_STI_UBOOT_H_ +#define __DWC3_STI_UBOOT_H_ + +#include <linux/usb/otg.h> + +/* glue registers */ +#define CLKRST_CTRL 0x00 +#define AUX_CLK_EN BIT(0) +#define SW_PIPEW_RESET_N BIT(4) +#define EXT_CFG_RESET_N BIT(8) + +#define XHCI_REVISION BIT(12) + +#define USB2_VBUS_MNGMNT_SEL1 0x2C +#define USB2_VBUS_UTMIOTG 0x1 + +#define SEL_OVERRIDE_VBUSVALID(n) ((n) << 0) +#define SEL_OVERRIDE_POWERPRESENT(n) ((n) << 4) +#define SEL_OVERRIDE_BVALID(n) ((n) << 8) + +/* Static DRD configuration */ +#define USB3_CONTROL_MASK 0xf77 + +#define USB3_DEVICE_NOT_HOST BIT(0) +#define USB3_FORCE_VBUSVALID BIT(1) +#define USB3_DELAY_VBUSVALID BIT(2) +#define USB3_SEL_FORCE_OPMODE BIT(4) +#define USB3_FORCE_OPMODE(n) ((n) << 5) +#define USB3_SEL_FORCE_DPPULLDOWN2 BIT(8) +#define USB3_FORCE_DPPULLDOWN2 BIT(9) +#define USB3_SEL_FORCE_DMPULLDOWN2 BIT(10) +#define USB3_FORCE_DMPULLDOWN2 BIT(11) + +int sti_dwc3_init(enum usb_dr_mode mode); + +#endif /* __DWC3_STI_UBOOT_H_ */

From: Patrice Chotard patrice.chotard@st.com

Add usb_gadget_handle_interrupts(), board_usb_init(), board_usb_cleanup() and g_dnl_board_usb_cable_connected() callbacks needed for FASTBOOT support

Signed-off-by: Patrice Chotard patrice.chotard@st.com ---

v4: _ none

v3: _ none

v2: _ none

board/st/stih410-b2260/board.c | 44 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 44 insertions(+)

diff --git a/board/st/stih410-b2260/board.c b/board/st/stih410-b2260/board.c index 92b0695..899a3e9 100644 --- a/board/st/stih410-b2260/board.c +++ b/board/st/stih410-b2260/board.c @@ -7,6 +7,9 @@ */

#include <common.h> +#include <dwc3-sti-glue.h> +#include <dwc3-uboot.h> +#include <usb.h>

DECLARE_GLOBAL_DATA_PTR;

@@ -36,3 +39,44 @@ int board_init(void) { return 0; } + +#ifdef CONFIG_USB_DWC3 +static struct dwc3_device dwc3_device_data = { + .maximum_speed = USB_SPEED_HIGH, + .dr_mode = USB_DR_MODE_PERIPHERAL, + .index = 0, +}; + +int usb_gadget_handle_interrupts(int index) +{ + dwc3_uboot_handle_interrupt(index); + return 0; +} + +int board_usb_init(int index, enum usb_init_type init) +{ + int node; + const void *blob = gd->fdt_blob; + + /* find the snps,dwc3 node */ + node = fdt_node_offset_by_compatible(blob, -1, "snps,dwc3"); + + dwc3_device_data.base = fdtdec_get_addr(blob, node, "reg"); + + /* init dwc3 glue with mode forced to PERIPHERAL */ + sti_dwc3_init(USB_DR_MODE_PERIPHERAL); + + return dwc3_uboot_init(&dwc3_device_data); +} + +int board_usb_cleanup(int index, enum usb_init_type init) +{ + dwc3_uboot_exit(index); + return 0; +} + +int g_dnl_board_usb_cable_connected(void) +{ + return 1; +} +#endif

From: Patrice Chotard patrice.chotard@st.com

Signed-off-by: Patrice Chotard patrice.chotard@st.com ---

v4: _ enable CONFIG_PHY and CONFIG_STI_USB_PHY

v3: _ none

v2: _ none

configs/stih410-b2260_defconfig | 37 +++++++++++++++++++++++++++++++++---- 1 file changed, 33 insertions(+), 4 deletions(-)

diff --git a/configs/stih410-b2260_defconfig b/configs/stih410-b2260_defconfig index 4e6942f..b106ff4 100644 --- a/configs/stih410-b2260_defconfig +++ b/configs/stih410-b2260_defconfig @@ -2,25 +2,54 @@ CONFIG_ARM=y CONFIG_ARCH_STI=y CONFIG_IDENT_STRING="STMicroelectronics STiH410-B2260" CONFIG_DEFAULT_DEVICE_TREE="stih410-b2260" +CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_FIT_VERBOSE=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SYS_PROMPT="stih410-b2260 => " +CONFIG_FASTBOOT=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_CMD_FASTBOOT=y +CONFIG_ANDROID_BOOT_IMAGE=y +CONFIG_FASTBOOT_BUF_ADDR=0x40000000 +CONFIG_FASTBOOT_BUF_SIZE=0x3DF00000 +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 # CONFIG_CMD_IMLS is not set +CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y CONFIG_CMD_TIME=y CONFIG_CMD_TIMER=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_EXT4=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_EXT4_WRITE=y +# CONFIG_ISO_PARTITION is not set CONFIG_OF_CONTROL=y CONFIG_REGMAP=y CONFIG_SYSCON=y +CONFIG_MISC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_STI=y +CONFIG_PHY=y +CONFIG_STI_USB_PHY=y CONFIG_PINCTRL=y +CONFIG_STI_RESET=y CONFIG_STI_ASC_SERIAL=y CONFIG_SYSRESET=y CONFIG_TIMER=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_STI=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GADGET=y +CONFIG_USB_STORAGE=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_G_DNL_MANUFACTURER="STMicroelectronics" +CONFIG_G_DNL_VENDOR_NUM=0x483 +CONFIG_G_DNL_PRODUCT_NUM=0x7270 +CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_SPL_OF_LIBFDT=y