----- Original Message ----- From: "Julian Pidancet" julian.pidancet@citrix.com To: u-boot@lists.denx.de Cc: "tanmay upadhyay" tanmay.upadhyay@einfochips.com, prafulla@marvell.com Sent: Tuesday, February 8, 2011 11:50:54 PM Subject: [PATCH] Kirkwood: Add support for OpenRD-Client & OpenRD-Ultimate

This patch modifies existing OpenRD-Base support to deal with all the three OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate).

This is a rebase onto master from an original patch sent by Tanmay Upadhyay a few months ago. All credits goes to him. It's been tested on my OpenRD-Ultimate and works perfectly fine.

Signed-off-by: Julian Pidancet julian.pidancet@citrix.com Acked by: Tanmay Upadhyay tanmay.upadhyay@einfochips.com --- MAKEALL | 2 + board/Marvell/openrd/Makefile | 56 ++++++++++ board/Marvell/openrd/config.mk | 33 ++++++ board/Marvell/openrd/kwbimage.cfg | 168 ++++++++++++++++++++++++++++++ board/Marvell/openrd/openrd.c | 173 +++++++++++++++++++++++++++++++ board/Marvell/openrd/openrd.h | 50 +++++++++ board/Marvell/openrd_base/Makefile | 56 ---------- board/Marvell/openrd_base/kwbimage.cfg | 168 ------------------------------ board/Marvell/openrd_base/openrd_base.c | 153 --------------------------- board/Marvell/openrd_base/openrd_base.h | 46 -------- boards.cfg | 4 +- include/configs/openrd.h | 115 ++++++++++++++++++++ include/configs/openrd_base.h | 92 +++-------------- include/configs/openrd_client.h | 50 +++++++++ include/configs/openrd_ultimate.h | 50 +++++++++ 15 files changed, 714 insertions(+), 502 deletions(-) create mode 100644 board/Marvell/openrd/Makefile create mode 100644 board/Marvell/openrd/config.mk create mode 100644 board/Marvell/openrd/kwbimage.cfg create mode 100644 board/Marvell/openrd/openrd.c create mode 100644 board/Marvell/openrd/openrd.h delete mode 100644 board/Marvell/openrd_base/Makefile delete mode 100644 board/Marvell/openrd_base/kwbimage.cfg delete mode 100644 board/Marvell/openrd_base/openrd_base.c delete mode 100644 board/Marvell/openrd_base/openrd_base.h create mode 100644 include/configs/openrd.h create mode 100644 include/configs/openrd_client.h create mode 100644 include/configs/openrd_ultimate.h

diff --git a/MAKEALL b/MAKEALL index a732e6a..4b6da98 100755 --- a/MAKEALL +++ b/MAKEALL @@ -361,6 +361,8 @@ LIST_ARM9=" \ omap5912osk \ omap730p2 \ openrd_base \ + openrd_client \ + openrd_ultimate \ rd6281a \ sbc2410x \ scb9328 \ diff --git a/board/Marvell/openrd/Makefile b/board/Marvell/openrd/Makefile new file mode 100644 index 0000000..19020e4 --- /dev/null +++ b/board/Marvell/openrd/Makefile @@ -0,0 +1,56 @@ +# +# (C) Copyright 2009 +# Net Insight < www.netinsight.net > +# Written-by: Simon Kagstrom simon.kagstrom@netinsight.net +# +# Based on sheevaplug: +# (C) Copyright 2009 +# Marvell Semiconductor < www.marvell.com > +# Written-by: Prafulla Wadaskar prafulla@marvell.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := openrd.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/Marvell/openrd/config.mk b/board/Marvell/openrd/config.mk new file mode 100644 index 0000000..8ae355e --- /dev/null +++ b/board/Marvell/openrd/config.mk @@ -0,0 +1,33 @@ +# +# (C) Copyright 2009 +# Net Insight < www.netinsight.net > +# Written-by: Simon Kagstrom simon.kagstrom@netinsight.net +# +# Based on sheevaplug: +# (C) Copyright 2009 +# Marvell Semiconductor < www.marvell.com > +# Written-by: Prafulla Wadaskar prafulla@marvell.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +TEXT_BASE = 0x00600000 + +# Kirkwood Boot Image configuration file +KWD_CONFIG = $(SRCTREE) / board / $(BOARDDIR)/kwbimage.cfg diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg new file mode 100644 index 0000000..757eb28 --- /dev/null +++ b/board/Marvell/openrd/kwbimage.cfg @@ -0,0 +1,168 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor < www.marvell.com > +# Written-by: Prafulla Wadaskar prafulla@marvell.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x000000cc # DDR Address Control +# bit1-0: 00, Cs0width=x8 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs1width=x8 +# bit7-6: 11, Cs1size=1Gb +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000042 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 1, DDR drive strength reduced +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low) +# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1 +# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0 +# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1. +# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0. +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) + +DATA 0xFFD0149C 0x0000E40f # CPU ODT Control +# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3 +# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm +# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm +# bit14: 1, M_STARTBURST_IN ODT: Enabled +# bit15: 1, DDR IO ODT Unit: Use ODT block +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c new file mode 100644 index 0000000..2d34a24 --- /dev/null +++ b/board/Marvell/openrd/openrd.c @@ -0,0 +1,173 @@ +/* + * Modified Simon's work to deal with all the three variants of + * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate) + * + * eInfochips < www.einfochips.com > + * Modified-by: Tanmay Upadhyay tanmay.upadhyay@einfochips.com + * + * (C) Copyright 2009 + * Net Insight < www.netinsight.net > + * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net + * + * Based on sheevaplug.c: + * (C) Copyright 2009 + * Marvell Semiconductor < www.marvell.com > + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <miiphy.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/mpp.h> +#include "openrd.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + kw_config_gpio(OPENRD_OE_VAL_LOW, + OPENRD_OE_VAL_HIGH, + OPENRD_OE_LOW, OPENRD_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, /* Alt UART1_TXD */ + MPP14_SD_D0, /* Alt UART1_RXD */ + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_TSMP9, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GPIO, /* UART1 / SD sel */ + MPP35_TDM_CH0_TX_QL, + MPP36_TDM_SPI_CS1, + MPP37_TDM_CH2_TX_QL, + MPP38_TDM_CH2_RX_QL, + MPP39_AUDIO_I2SBCLK, + MPP40_AUDIO_I2SDO, + MPP41_AUDIO_I2SLRC, + MPP42_AUDIO_I2SMCLK, + MPP43_AUDIO_I2SDI, + MPP44_AUDIO_EXTCLK, + MPP45_TDM_PCLK, + MPP46_TDM_FS, + MPP47_TDM_DRX, + MPP48_TDM_DTX, + MPP49_TDM_CH0_RX_QL, + 0 + }; + + kirkwood_mpp_conf(kwmpp_config); + return 0; +} + +int board_init(void) +{ + /* + * arch number of board + */ + gd->bd->bi_arch_number = MACH_TYPE_OPENRD; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +/* Configure and enable MV88E1116/MV88E1121 PHY */ +void mv_phy_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { + printf("Err..%s could not read PHY dev address\n", __func__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, PGADR_REG, 2); + miiphy_read(name, devadr, MAC_CTRL_REG, &reg); + reg |= (RGMII_RXTM_CTRL | RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MAC_CTRL_REG, reg); + miiphy_write(name, devadr, PGADR_REG, 0); + + /* reset the phy */ + if (!miiphy_reset(name, devadr)) + printf("%s Initialized on %s\n", PHY_NO, name); +} + +void reset_phy(void) +{ + mv_phy_init("egiga0"); + +#ifdef OPENRD_CLIENT + /* Kirkwood ethernet driver is written with the assumption that in case + * of multiple PHYs, their addresses are consecutive. But unfortunately + * in case of OpenRD-Client, PHY addresses are not consecutive.*/ + miiphy_write("egiga1", 0xEE, 0xEE, 24); +#endif + +#if defined(OPENRD_CLIENT) || defined(OPENRD_ULTIMATE) + /* configure and initialize both PHY's */ + mv_phy_init("egiga1"); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/openrd/openrd.h b/board/Marvell/openrd/openrd.h new file mode 100644 index 0000000..2fe2e19 --- /dev/null +++ b/board/Marvell/openrd/openrd.h @@ -0,0 +1,50 @@ +/* + * Modified Simon's work to deal with all the three variants of + * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate) + * + * eInfochips < www.einfochips.com > + * Modified-by: Tanmay Upadhyay tanmay.upadhyay@einfochips.com + * + * (C) Copyright 2009 + * Net Insight < www.netinsight.net > + * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net + * + * Based on sheevaplug.h: + * (C) Copyright 2009 + * Marvell Semiconductor < www.marvell.com > + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef __OPENRD_H +#define __OPENRD_H + +#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */ +#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */ +#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */ +#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */ + +/* PHY related */ +#define MAC_CTRL_REG 21 +#define PGADR_REG 22 +#define RGMII_TXTM_CTRL (1 << 4) +#define RGMII_RXTM_CTRL (1 << 5) + +#endif /* __OPENRD_H */ diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile deleted file mode 100644 index d6d0ed3..0000000 --- a/board/Marvell/openrd_base/Makefile +++ /dev/null @@ -1,56 +0,0 @@ -# -# (C) Copyright 2009 -# Net Insight < www.netinsight.net > -# Written-by: Simon Kagstrom simon.kagstrom@netinsight.net -# -# Based on sheevaplug: -# (C) Copyright 2009 -# Marvell Semiconductor < www.marvell.com > -# Written-by: Prafulla Wadaskar prafulla@marvell.com -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, -# MA 02110-1301 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).o - -COBJS := openrd_base.o - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(obj).depend $(OBJS) $(SOBJS) - $(call cmd_link_o_target, $(OBJS) $(SOBJS)) - -clean: - rm -f $(SOBJS) $(OBJS) - -distclean: clean - rm -f $(LIB) core *.bak .depend - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/Marvell/openrd_base/kwbimage.cfg b/board/Marvell/openrd_base/kwbimage.cfg deleted file mode 100644 index 757eb28..0000000 --- a/board/Marvell/openrd_base/kwbimage.cfg +++ /dev/null @@ -1,168 +0,0 @@ -# -# (C) Copyright 2009 -# Marvell Semiconductor < www.marvell.com > -# Written-by: Prafulla Wadaskar prafulla@marvell.com -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, -# MA 02110-1301 USA -# -# Refer docs/README.kwimage for more details about how-to configure -# and create kirkwood boot image -# - -# Boot Media configurations -BOOT_FROM nand -NAND_ECC_MODE default -NAND_PAGE_SIZE 0x0800 - -# SOC registers configuration using bootrom header extension -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed - -# Configure RGMII-0 interface pad voltage to 1.8V -DATA 0xFFD100e0 0x1b1b1b9b - -#Dram initalization for SINGLE x16 CL=5 @ 400MHz -DATA 0xFFD01400 0x43000c30 # DDR Configuration register -# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) -# bit23-14: zero -# bit24: 1= enable exit self refresh mode on DDR access -# bit25: 1 required -# bit29-26: zero -# bit31-30: 01 - -DATA 0xFFD01404 0x37543000 # DDR Controller Control Low -# bit 4: 0=addr/cmd in smame cycle -# bit 5: 0=clk is driven during self refresh, we don't care for APX -# bit 6: 0=use recommended falling edge of clk for addr/cmd -# bit14: 0=input buffer always powered up -# bit18: 1=cpu lock transaction enabled -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 -# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM -# bit30-28: 3 required -# bit31: 0=no additional STARTBURST delay - -DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) -# bit3-0: TRAS lsbs -# bit7-4: TRCD -# bit11- 8: TRP -# bit15-12: TWR -# bit19-16: TWTR -# bit20: TRAS msb -# bit23-21: 0x0 -# bit27-24: TRRD -# bit31-28: TRTP - -DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) -# bit6-0: TRFC -# bit8-7: TR2R -# bit10-9: TR2W -# bit12-11: TW2W -# bit31-13: zero required - -DATA 0xFFD01410 0x000000cc # DDR Address Control -# bit1-0: 00, Cs0width=x8 -# bit3-2: 11, Cs0size=1Gb -# bit5-4: 00, Cs1width=x8 -# bit7-6: 11, Cs1size=1Gb -# bit9-8: 00, Cs2width=nonexistent -# bit11-10: 00, Cs2size =nonexistent -# bit13-12: 00, Cs3width=nonexistent -# bit15-14: 00, Cs3size =nonexistent -# bit16: 0, Cs0AddrSel -# bit17: 0, Cs1AddrSel -# bit18: 0, Cs2AddrSel -# bit19: 0, Cs3AddrSel -# bit31-20: 0 required - -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control -# bit0: 0, OpenPage enabled -# bit31-1: 0 required - -DATA 0xFFD01418 0x00000000 # DDR Operation -# bit3-0: 0x0, DDR cmd -# bit31-4: 0 required - -DATA 0xFFD0141C 0x00000C52 # DDR Mode -# bit2-0: 2, BurstLen=2 required -# bit3: 0, BurstType=0 required -# bit6-4: 4, CL=5 -# bit7: 0, TestMode=0 normal -# bit8: 0, DLL reset=0 normal -# bit11-9: 6, auto-precharge write recovery ???????????? -# bit12: 0, PD must be zero -# bit31-13: 0 required - -DATA 0xFFD01420 0x00000042 # DDR Extended Mode -# bit0: 0, DDR DLL enabled -# bit1: 1, DDR drive strength reduced -# bit2: 0, DDR ODT control lsd (disabled) -# bit5-3: 000, required -# bit6: 1, DDR ODT control msb, (disabled) -# bit9-7: 000, required -# bit10: 0, differential DQS enabled -# bit11: 0, required -# bit12: 0, DDR output buffer enabled -# bit31-13: 0 required - -DATA 0xFFD01424 0x0000F17F # DDR Controller Control High -# bit2-0: 111, required -# bit3 : 1 , MBUS Burst Chop disabled -# bit6-4: 111, required -# bit7 : 0 -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz -# bit9 : 0 , no half clock cycle addition to dataout -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh -# bit15-12: 1111 required -# bit31-16: 0 required - -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) - -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 -DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size -# bit0: 1, Window enabled -# bit1: 0, Write Protect disabled -# bit3-2: 00, CS0 hit selected -# bit23-4: ones, required -# bit31-24: 0x0F, Size (i.e. 256MB) - -DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb -DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 - -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled - -DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low) -# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1 -# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0 -# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1. -# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0. -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) - -DATA 0xFFD0149C 0x0000E40f # CPU ODT Control -# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3 -# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm -# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm -# bit14: 1, M_STARTBURST_IN ODT: Enabled -# bit15: 1, DDR IO ODT Unit: Use ODT block -DATA 0xFFD01480 0x00000001 # DDR Initialization Control -#bit0=1, enable DDR init upon this register write - -# End of Header extension -DATA 0x0 0x0 diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c deleted file mode 100644 index 10109c1..0000000 --- a/board/Marvell/openrd_base/openrd_base.c +++ /dev/null @@ -1,153 +0,0 @@ -/* - * (C) Copyright 2009 - * Net Insight < www.netinsight.net > - * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net - * - * Based on sheevaplug.c: - * (C) Copyright 2009 - * Marvell Semiconductor < www.marvell.com > - * Written-by: Prafulla Wadaskar prafulla@marvell.com - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA - */ - -#include <common.h> -#include <miiphy.h> -#include <asm/arch/kirkwood.h> -#include <asm/arch/mpp.h> -#include "openrd_base.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* - * default gpio configuration - * There are maximum 64 gpios controlled through 2 sets of registers - * the below configuration configures mainly initial LED status - */ - kw_config_gpio(OPENRD_OE_VAL_LOW, - OPENRD_OE_VAL_HIGH, - OPENRD_OE_LOW, OPENRD_OE_HIGH); - - /* Multi-Purpose Pins Functionality configuration */ - u32 kwmpp_config[] = { - MPP0_NF_IO2, - MPP1_NF_IO3, - MPP2_NF_IO4, - MPP3_NF_IO5, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, - MPP8_TW_SDA, - MPP9_TW_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP12_SD_CLK, - MPP13_SD_CMD, /* Alt UART1_TXD */ - MPP14_SD_D0, /* Alt UART1_RXD */ - MPP15_SD_D1, - MPP16_SD_D2, - MPP17_SD_D3, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_GE1_0, - MPP21_GE1_1, - MPP22_GE1_2, - MPP23_GE1_3, - MPP24_GE1_4, - MPP25_GE1_5, - MPP26_GE1_6, - MPP27_GE1_7, - MPP28_GPIO, - MPP29_TSMP9, - MPP30_GE1_10, - MPP31_GE1_11, - MPP32_GE1_12, - MPP33_GE1_13, - MPP34_GPIO, /* UART1 / SD sel */ - MPP35_TDM_CH0_TX_QL, - MPP36_TDM_SPI_CS1, - MPP37_TDM_CH2_TX_QL, - MPP38_TDM_CH2_RX_QL, - MPP39_AUDIO_I2SBCLK, - MPP40_AUDIO_I2SDO, - MPP41_AUDIO_I2SLRC, - MPP42_AUDIO_I2SMCLK, - MPP43_AUDIO_I2SDI, - MPP44_AUDIO_EXTCLK, - MPP45_TDM_PCLK, - MPP46_TDM_FS, - MPP47_TDM_DRX, - MPP48_TDM_DTX, - MPP49_TDM_CH0_RX_QL, - 0 - }; - - kirkwood_mpp_conf(kwmpp_config); - return 0; -} - -int board_init(void) -{ - /* - * arch number of board - */ - gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; - return 0; -} - -#ifdef CONFIG_RESET_PHY_R -/* Configure and enable MV88E1116 PHY */ -void reset_phy(void) -{ - u16 reg; - u16 devadr; - char *name = "egiga0"; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..%s could not read PHY dev address\n", - __FUNCTION__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - miiphy_reset(name, devadr); - - printf("88E1116 Initialized on %s\n", name); -} -#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h deleted file mode 100644 index f3daf17..0000000 --- a/board/Marvell/openrd_base/openrd_base.h +++ /dev/null @@ -1,46 +0,0 @@ -/* - * (C) Copyright 2009 - * Net Insight < www.netinsight.net > - * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net - * - * Based on sheevaplug.h: - * (C) Copyright 2009 - * Marvell Semiconductor < www.marvell.com > - * Written-by: Prafulla Wadaskar prafulla@marvell.com - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA - */ - -#ifndef __OPENRD_BASE_H -#define __OPENRD_BASE_H - -#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */ -#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */ -#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */ -#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */ - -/* PHY related */ -#define MV88E1116_LED_FCTRL_REG 10 -#define MV88E1116_CPRSP_CR3_REG 21 -#define MV88E1116_MAC_CTRL_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __OPENRD_BASE_H */ diff --git a/boards.cfg b/boards.cfg index c977528..4334630 100644 --- a/boards.cfg +++ b/boards.cfg @@ -96,7 +96,9 @@ davinci_sonata arm arm926ejs sonata davinci suen3 arm arm926ejs km_arm keymile kirkwood guruplug arm arm926ejs - Marvell kirkwood mv88f6281gtw_ge arm arm926ejs - Marvell kirkwood -openrd_base arm arm926ejs - Marvell kirkwood +openrd_base arm arm926ejs openrd Marvell kirkwood +openrd_client arm arm926ejs openrd Marvell kirkwood +openrd_ultimate arm arm926ejs openrd Marvell kirkwood rd6281a arm arm926ejs - Marvell kirkwood sheevaplug arm arm926ejs - Marvell kirkwood dockstar arm arm926ejs - Seagate kirkwood diff --git a/include/configs/openrd.h b/include/configs/openrd.h new file mode 100644 index 0000000..850dbae --- /dev/null +++ b/include/configs/openrd.h @@ -0,0 +1,115 @@ +/* + * Modified openrd_base.h to deal with all the three variants of + * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate) + * + * eInfochips < www.einfochips.com > + * Modified-by: Tanmay Upadhyay tanmay.upadhyay@einfochips.com + * + * (C) Copyright 2009 + * Net Insight < www.netinsight.net > + * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net + * + * Based on sheevaplug.h: + * (C) Copyright 2009 + * Marvell Semiconductor < www.marvell.com > + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _CONFIG_OPENRD_H +#define _CONFIG_OPENRD_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ +#define CONFIG_KIRKWOOD 1 /* SOC Family Name */ +#define CONFIG_KW88F6281 1 /* SOC Name */ +#define CONFIG_MACH_OPENRD_BASE /* Machine type */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#include <config_cmd_default.h> +#define CONFIG_CMD_AUTOSCRIPT +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_PING +#define CONFIG_CMD_USB +#define CONFIG_CMD_IDE + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* + * Environment variables configurations + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ +#else +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ +#endif +/* + * max 4k env size is enough, but in case of nand + * it has to be rounded to sector size + */ +#define CONFIG_ENV_SIZE 0x20000 /* 128k */ +#define CONFIG_ENV_ADDR 0x60000 +#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ + +/* + * Default environment variables + */ +#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ + "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ + "${x_bootcmd_usb}; bootm 0x6400000;" + +#define MTDIDS_DEFAULT "nand0=nand_mtd" +#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\ + "0x400000@0x100000(uImage),"\ + "0x1fb00000@0x500000(rootfs)" + +#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \ + "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ + "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ + "x_bootcmd_usb=usb start\0" \ + "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \ + "mtdids="MTDIDS_DEFAULT"\0" \ + "mtdparts="MTDPARTS_DEFAULT"\0" + +/* + * SATA Driver configuration + */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif / * CONFIG_MVSATA_IDE * / + +/* board_early_init_f function in openrd.c initializes all MPP settings */ +#define CONFIG_BOARD_EARLY_INIT_F +#endif /* _CONFIG_OPENRD_H */ diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h index cfdd09c..4f9ea80 100644 --- a/include/configs/openrd_base.h +++ b/include/configs/openrd_base.h @@ -1,4 +1,10 @@ /* + * Modified Simon's work to deal with all the three variants of + * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate) + * + * eInfochips < www.einfochips.com > + * Modified-by: Tanmay Upadhyay tanmay.upadhyay@einfochips.com + * * (C) Copyright 2009 * Net Insight < www.netinsight.net > * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net @@ -30,91 +36,21 @@ #ifndef _CONFIG_OPENRD_BASE_H #define _CONFIG_OPENRD_BASE_H

-/* - * Version number information - */ -#define CONFIG_IDENT_STRING "\nOpenRD_base" - -/* - * High Level Configuration Options (easy to change) - */ -#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ -#define CONFIG_KIRKWOOD 1 /* SOC Family Name */ -#define CONFIG_KW88F6281 1 /* SOC Name */ -#define CONFIG_MACH_OPENRD_BASE /* Machine type */ -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ - -/* - * Commands configuration - */ -#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ -#include <config_cmd_default.h> -#define CONFIG_CMD_AUTOSCRIPT -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ENV -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_PING -#define CONFIG_CMD_USB -#define CONFIG_CMD_IDE - -/* - * mv-common.h should be defined after CMD configs since it used them - * to enable certain macros - */ -#include "mv-common.h" - -/* - * Environment variables configurations - */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_ENV_IS_IN_NAND 1 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ -#else -#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ -#endif -/* - * max 4k env size is enough, but in case of nand - * it has to be rounded to sector size - */ -#define CONFIG_ENV_SIZE 0x20000 /* 128k */ -#define CONFIG_ENV_ADDR 0x60000 -#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ - -/* - * Default environment variables - */ -#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ - "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ - "${x_bootcmd_usb}; bootm 0x6400000;" +#include <configs/openrd.h>

-#define MTDIDS_DEFAULT "nand0=nand_mtd" -#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\ - "0x400000@0x100000(uImage),"\ - "0x1fb00000@0x500000(rootfs)" +#define CONFIG_IDENT_STRING "\nOpenRD-Base"

-#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \ - "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ - "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ - "x_bootcmd_usb=usb start\0" \ - "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \ - "mtdids="MTDIDS_DEFAULT"\0" \ - "mtdparts="MTDPARTS_DEFAULT"\0" +/* Machine type */ +#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_BASE

/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ -#define CONFIG_PHY_BASE_ADR 0x8 +/* enable port 0 only */ +#define CONFIG_MVGBE_PORTS {1, 0} +#define CONFIG_PHY_BASE_ADR 0x8 +#define PHY_NO "88E1116" #endif /* CONFIG_CMD_NET */

-/* - * SATA Driver configuration - */ -#ifdef CONFIG_MVSATA_IDE -#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET -#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET -#endif / * CONFIG_MVSATA_IDE * / - #endif /* _CONFIG_OPENRD_BASE_H */ diff --git a/include/configs/openrd_client.h b/include/configs/openrd_client.h new file mode 100644 index 0000000..98d516a --- /dev/null +++ b/include/configs/openrd_client.h @@ -0,0 +1,50 @@ +/* + * Created to deal with all the three variants of OpenRD boards + * (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate) + * + * eInfochips < www.einfochips.com > + * Written-by: Tanmay Upadhyay tanmay.upadhyay@einfochips.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _CONFIG_OPENRD_CLIENT_H +#define _CONFIG_OPENRD_CLIENT_H + +#include <configs/openrd.h> + +#define CONFIG_IDENT_STRING "\nOpenRD-Client" + +/* Machine type */ +#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_CLIENT + +/* board/openrd/openrd.c needs this */ +#define OPENRD_CLIENT + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +/* enable port 0 only */ +#define CONFIG_MVGBE_PORTS {1, 1} +#define CONFIG_PHY_BASE_ADR 0x8 +#define PHY_NO "88E1116" +#endif /* CONFIG_CMD_NET */ + +#endif /* _CONFIG_OPENRD_CLIENT_H */ diff --git a/include/configs/openrd_ultimate.h b/include/configs/openrd_ultimate.h new file mode 100644 index 0000000..4d20717 --- /dev/null +++ b/include/configs/openrd_ultimate.h @@ -0,0 +1,50 @@ +/* + * Created to deal with all the three variants of OpenRD boards + * (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate) + * + * eInfochips < www.einfochips.com > + * Written-by: Tanmay Upadhyay tanmay.upadhyay@einfochips.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _CONFIG_OPENRD_ULTIMATE_H +#define _CONFIG_OPENRD_ULTIMATE_H + +#include <configs/openrd.h> + +#define CONFIG_IDENT_STRING "\nOpenRD-Ultimate" + +/* Machine type */ +#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_ULTIMATE + +/* board/openrd/openrd.c needs this */ +#define OPENRD_ULTIMATE + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +/* enable port 0 only */ +#define CONFIG_MVGBE_PORTS {1, 1} +#define CONFIG_PHY_BASE_ADR 0x0 +#define PHY_NO "88E1121" +#endif /* CONFIG_CMD_NET */ + +#endif /* _CONFIG_OPENRD_ULTIMATE_H */ -- 1.7.4