V3 NAND_SPL support for phycore imx31

This patch is applied on U-Boot v2008.10 release.

Changelog:

* Added infinitive loop for ecc-error cases; * Correct to code-style; * Was changed mx31_nand_data_output function for support 2-k NAND page chips (Magnus Lilja proposal); * Was changed name of CFG_NAND_PAGE_COUNT by CFG_NAND_PAGES_PER_BLOCK;

> V2 NAND_SPL support for phycore imx31 > > Changelog: > > * Added bad block verify & skip; > * Correct to code-style; > * Added few comments;

>> V1 nand booting support (SPL) for phyCORE-i.MX31 >> >> This patch allows Phytec phyCORE-i.MX31 based >> system to boot from embed NAND-flash memory. >> It not add support for NAND cmd and/or driver >> for U-BOOT, it is only SPL for U-BOOT. For NAND >> support in U-BOOT I give refer to Magnus Lilja's >> aug/2008 patch series for PDK/Litekit boards. >> ("[U-Boot] [PATCH v3 4/6] i.MX31: Add i.MX31 >> NAND Flash Controller driver."; MID 1219998982- >> 21289-5-git-send-email-lilja.magnus@gmail.com) >> >> Some note: by default, Phytec phyCORE-i.MX31 >> board (pcm-037 on pcm-970) is not suitable >> for nand-bootloading, because of SW5 switchers >> block haven't appropriate modes(8-bit, 2k page >> or 16-bit, 512B page) for BOOTPINS[4:0] and >> nand-flash(8-bit mode, 512B page) contemporary. >> There is require to make RESOLDER for really >> nand-booting either BOOTPIN state or JN1/2 and >> RN41/42. >> >> This nand-spl work with 8-bit, 512B page size nand-flash.

Signed-off-by: Maxim Artamonov <scn1874 at yandex.ru> --- MAKEALL | 1 + Makefile | 9 ++- board/imx31_phycore/config.mk | 10 ++ board/imx31_phycore/lowlevel_init.S | 27 ++++- board/imx31_phycore/u-boot-nand.lds | 62 ++++++++++ cpu/arm1136/start.S | 36 ++++-- include/asm-arm/arch-mx31/mx31-regs.h | 96 +++++++++++++++ include/configs/imx31_phycore.h | 33 +++++ nand_spl/board/imx31_phycore/Makefile | 95 +++++++++++++++ nand_spl/board/imx31_phycore/config.mk | 33 +++++ nand_spl/board/imx31_phycore/u-boot.lds | 65 ++++++++++ nand_spl/nand_boot_mx31.c | 200 +++++++++++++++++++++++++++++++ 12 files changed, 656 insertions(+), 11 deletions(-) create mode 100644 board/imx31_phycore/u-boot-nand.lds create mode 100644 nand_spl/board/imx31_phycore/Makefile create mode 100644 nand_spl/board/imx31_phycore/config.mk create mode 100644 nand_spl/board/imx31_phycore/u-boot.lds create mode 100644 nand_spl/nand_boot_mx31.c

diff --git a/MAKEALL b/MAKEALL index 9ccb9ac..1f639a8 100755 --- a/MAKEALL +++ b/MAKEALL @@ -522,6 +522,7 @@ LIST_ARM11=" \ apollon \ imx31_litekit \ imx31_phycore \ + imx31_phycore_nand \ mx31ads \ smdk6400 \ " diff --git a/Makefile b/Makefile index 58b8331..7519dfe 100644 --- a/Makefile +++ b/Makefile @@ -353,7 +353,7 @@ $(NAND_SPL): $(VERSION_FILE) $(obj)include/autoconf.mk $(MAKE) -C nand_spl/board/$(BOARDDIR) all

$(U_BOOT_NAND): $(NAND_SPL) $(obj)u-boot.bin $(obj)include/autoconf.mk - cat $(obj)nand_spl/u-boot-spl-16k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin + cat $(obj)nand_spl/u-boot-spl-aligned.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin

$(ONENAND_IPL): $(VERSION_FILE) $(obj)include/autoconf.mk $(MAKE) -C onenand_ipl/board/$(BOARDDIR) all @@ -2805,6 +2805,13 @@ imx31_litekit_config : unconfig imx31_phycore_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 imx31_phycore NULL mx31

+imx31_phycore_nand_config : unconfig + @mkdir -p $(obj)include $(obj)board/imx31_phycore + @mkdir -p $(obj)nand_spl/board/imx31_phycore + @echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h + @$(MKCONFIG) -n $@ -a imx31_phycore arm arm1136 imx31_phycore NULL mx31 + @echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk + mx31ads_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31

diff --git a/board/imx31_phycore/config.mk b/board/imx31_phycore/config.mk index d34dc02..412defc 100644 --- a/board/imx31_phycore/config.mk +++ b/board/imx31_phycore/config.mk @@ -1 +1,11 @@ +# +# (C) Copyright 2008 +# was changed by Maxim Artamonov, <scn1874 at yandex.ru> +# + +ifndef CONFIG_NAND_SPL TEXT_BASE = 0x87f00000 +else +TEXT_BASE = 0x87ec0000 +endif + diff --git a/board/imx31_phycore/lowlevel_init.S b/board/imx31_phycore/lowlevel_init.S index c5d6eb0..afae317 100644 --- a/board/imx31_phycore/lowlevel_init.S +++ b/board/imx31_phycore/lowlevel_init.S @@ -1,5 +1,7 @@ /* - * + * (C) Copyright 2008 + * Maxim Artamonov, <scn1874 at yandex.ru> + * * (c) 2007 Pengutronix, Sascha Hauer s.hauer@pengutronix.de * * See file CREDITS for list of people who contributed to this @@ -43,6 +45,20 @@ bcs 1b .endm

+#ifdef CONFIG_NAND_SPL +/* somewhat macro to reduce bin size for CONFIG_NAND_SPL*/ +.macro FILLREGS begreg, val, count, step + ldr r2, =\begreg + ldr r3, =\val + ldr r4, =\count +2: + str r3, [r2] + add r2, r2, #\step + subs r4, r4, #1 + bcs 2b +.endm +#endif + .globl lowlevel_init lowlevel_init:

@@ -60,10 +76,18 @@ lowlevel_init:

REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(0x43) | PLL_MFI(12) | PLL_MFN(1)

+#ifdef CONFIG_NAND_SPL + FILLREGS 0x43FAC26C, 0, 0x3, 0x4 +#else REG 0x43FAC26C, 0 /* SDCLK */ REG 0x43FAC270, 0 /* CAS */ REG 0x43FAC274, 0 /* RAS */ +#endif /* CONFIG_NAND_SPL */ REG 0x43FAC27C, 0x1000 /* CS2 (CSD0) */ + +#ifdef CONFIG_NAND_SPL + FILLREGS 0x43FAC284, 0, 0x17, 0x4 +#else REG 0x43FAC284, 0 /* DQM3 */ REG 0x43FAC288, 0 /* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */ REG 0x43FAC28C, 0 @@ -87,6 +111,7 @@ lowlevel_init: REG 0x43FAC2D4, 0 REG 0x43FAC2D8, 0 REG 0x43FAC2DC, 0 +#endif /* CONFIG_NAND_SPL */ REG 0xB8001010, 0x00000004 REG 0xB8001004, 0x006ac73a REG 0xB8001000, 0x92100000 diff --git a/board/imx31_phycore/u-boot-nand.lds b/board/imx31_phycore/u-boot-nand.lds new file mode 100644 index 0000000..bd09a8d --- /dev/null +++ b/board/imx31_phycore/u-boot-nand.lds @@ -0,0 +1,62 @@ +/* + * (C) Copyright 2008 + * Maxim Artamonov, <scn1874 at yandex.ru> + * + * January 2004 - Changed to support H4 device + * Copyright (c) 2004 Texas Instruments + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, gj@denx.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/arm1136/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/cpu/arm1136/start.S b/cpu/arm1136/start.S index 51b664d..596efe9 100644 --- a/cpu/arm1136/start.S +++ b/cpu/arm1136/start.S @@ -1,6 +1,9 @@ /* * armboot - Startup Code for OMP2420/ARM1136 CPU-core * + * + * Copyright (c) 2008 Maxim Artamonov, <scn1874 at yandex.ru> + * * Copyright (c) 2004 Texas Instruments r-woodruff2@ti.com * * Copyright (c) 2001 Marius Gr�ger mag@sysgo.de @@ -32,6 +35,15 @@ #include <version.h> .globl _start _start: b reset +#ifdef CONFIG_NAND_SPL + nop + nop + nop + nop + nop + nop + nop +#else #ifdef CONFIG_ONENAND_IPL ldr pc, _hang ldr pc, _hang @@ -68,6 +80,7 @@ _irq: .word irq _fiq: .word fiq _pad: .word 0x12345678 /* now 16*4=64 */ #endif /* CONFIG_ONENAND_IPL */ +#endif /* CONFIG_NAND_SPL */ .global _end_vect _end_vect:

@@ -156,9 +169,9 @@ relocate: /* relocate U-Boot to RAM */ adr r0, _start /* r0 <- current position of code */ ldr r1, _TEXT_BASE /* test if we run from flash or RAM */ cmp r0, r1 /* don't reloc during debug */ -#ifndef CONFIG_ONENAND_IPL +#if !defined(CONFIG_ONENAND_IPL) && !defined(CONFIG_NAND_SPL) beq stack_setup -#endif /* CONFIG_ONENAND_IPL */ +#endif /* !CONFIG_ONENAND_IPL && !CONFIG_NAND_SPL*/

ldr r2, _armboot_start ldr r3, _bss_start @@ -175,7 +188,7 @@ copy_loop: /* Set up the stack */ stack_setup: ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */ -#ifdef CONFIG_ONENAND_IPL +#if defined(CONFIG_ONENAND_IPL) || defined (CONFIG_NAND_SPL) sub sp, r0, #128 /* leave 32 words for abort-stack */ #else sub r0, r0, #CFG_MALLOC_LEN /* malloc area */ @@ -184,14 +197,14 @@ stack_setup: sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ) #endif sub sp, r0, #12 /* leave 3 words for abort-stack */ -#endif /* CONFIG_ONENAND_IPL */ +#endif /* CONFIG_ONENAND_IPL || CONFIG_NAND_SPL*/

clear_bss: ldr r0, _bss_start /* find start of bss segment */ ldr r1, _bss_end /* stop here */ mov r2, #0x00000000 /* clear */

-#ifndef CONFIG_ONENAND_IPL +#if !defined(CONFIG_ONENAND_IPL) && !defined(CONFIG_NAND_SPL) clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 @@ -200,12 +213,15 @@ clbss_l:str r2, [r0] /* clear loop... */

ldr pc, _start_armboot

+#ifdef CONFIG_NAND_SPL +_start_armboot: .word nand_boot +#else #ifdef CONFIG_ONENAND_IPL _start_armboot: .word start_oneboot #else _start_armboot: .word start_armboot -#endif - +#endif /* CONFIG_ONENAND_IPL */ +#endif /* CONFIG_NAND_SPL */

/* ************************************************************************* @@ -244,7 +260,7 @@ cpu_init_crit: mov lr, ip /* restore link */ mov pc, lr /* back to my caller */

-#ifndef CONFIG_ONENAND_IPL +#if !defined(CONFIG_ONENAND_IPL) && !defined(CONFIG_NAND_SPL) /* ************************************************************************* * @@ -357,11 +373,12 @@ cpu_init_crit: .macro get_fiq_stack @ setup FIQ stack ldr sp, FIQ_STACK_START .endm -#endif /* CONFIG_ONENAND_IPL */ +#endif /* !CONFIG_ONENAND_IPL && !CONFIG_NAND_SPL*/

/* * exception handlers */ +#ifndef CONFIG_NAND_SPL #ifdef CONFIG_ONENAND_IPL .align 5 do_hang: @@ -436,3 +453,4 @@ arm1136_cache_flush: mcr p15, 0, r1, c7, c5, 0 @ invalidate I cache mov pc, lr @ back to caller #endif /* CONFIG_ONENAND_IPL */ +#endif /* !CONFIG_NAND_SPL*/ diff --git a/include/asm-arm/arch-mx31/mx31-regs.h b/include/asm-arm/arch-mx31/mx31-regs.h index b04a718..78825f5 100644 --- a/include/asm-arm/arch-mx31/mx31-regs.h +++ b/include/asm-arm/arch-mx31/mx31-regs.h @@ -168,4 +168,100 @@ #define CS5_BASE 0xB6000000 #define PCMCIA_MEM_BASE 0xC0000000

+/* + * NAND controller + */ +#define NFC_BASE_ADDR 0xB8000000 + +/* + * Addresses for NFC registers + */ +#define NFC_BUF_SIZE (*((volatile u16 *)(NFC_BASE_ADDR + 0xE00))) +#define NFC_BUF_ADDR (*((volatile u16 *)(NFC_BASE_ADDR + 0xE04))) +#define NFC_FLASH_ADDR (*((volatile u16 *)(NFC_BASE_ADDR + 0xE06))) +#define NFC_FLASH_CMD (*((volatile u16 *)(NFC_BASE_ADDR + 0xE08))) +#define NFC_CONFIG (*((volatile u16 *)(NFC_BASE_ADDR + 0xE0A))) +#define NFC_ECC_STATUS_RESULT (*((volatile u16 *)(NFC_BASE_ADDR + 0xE0C))) +#define NFC_RSLTMAIN_AREA (*((volatile u16 *)(NFC_BASE_ADDR + 0xE0E))) +#define NFC_RSLTSPARE_AREA (*((volatile u16 *)(NFC_BASE_ADDR + 0xE10))) +#define NFC_WRPROT (*((volatile u16 *)(NFC_BASE_ADDR + 0xE12))) +#define NFC_UNLOCKSTART_BLKADDR (*((volatile u16 *)(NFC_BASE_ADDR + 0xE14))) +#define NFC_UNLOCKEND_BLKADDR (*((volatile u16 *)(NFC_BASE_ADDR + 0xE16))) +#define NFC_NF_WRPRST (*((volatile u16 *)(NFC_BASE_ADDR + 0xE18))) +#define NFC_CONFIG1 (*((volatile u16 *)(NFC_BASE_ADDR + 0xE1A))) +#define NFC_CONFIG2 (*((volatile u16 *)(NFC_BASE_ADDR + 0xE1C))) + +/* + * Addresses for NFC RAM BUFFER Main area 0 + */ +#define MAIN_AREA0 (volatile u16 *)(NFC_BASE_ADDR + 0x000) +#define MAIN_AREA1 (volatile u16 *)(NFC_BASE_ADDR + 0x200) +#define MAIN_AREA2 (volatile u16 *)(NFC_BASE_ADDR + 0x400) +#define MAIN_AREA3 (volatile u16 *)(NFC_BASE_ADDR + 0x600) + +/* + * Addresses for NFC SPARE BUFFER Spare area 0 + */ +#define SPARE_AREA0 (volatile u16 *)(NFC_BASE_ADDR + 0x800) +#define SPARE_AREA1 (volatile u16 *)(NFC_BASE_ADDR + 0x810) +#define SPARE_AREA2 (volatile u16 *)(NFC_BASE_ADDR + 0x820) +#define SPARE_AREA3 (volatile u16 *)(NFC_BASE_ADDR + 0x830) + +/* + * Set INT to 0, FCMD to 1, rest to 0 in NFC_CONFIG2 Register for Command + * operation + */ +#define NFC_CMD 0x1 + +/* + * Set INT to 0, FADD to 1, rest to 0 in NFC_CONFIG2 Register for Address + * operation + */ +#define NFC_ADDR 0x2 + +/* + * Set INT to 0, FDI to 1, rest to 0 in NFC_CONFIG2 Register for Input + * operation + */ +#define NFC_INPUT 0x4 + +/* + * Set INT to 0, FDO to 001, rest to 0 in NFC_CONFIG2 Register for Data + * Output operation + */ +#define NFC_OUTPUT 0x8 + +/* + * Set INT to 0, FD0 to 010, rest to 0 in NFC_CONFIG2 Register for Read ID + * operation + */ +#define NFC_ID 0x10 + +/* + * Set INT to 0, FDO to 100, rest to 0 in NFC_CONFIG2 Register for Read + * Status operation + */ +#define NFC_STATUS 0x20 + +/* + * Set INT to 1, rest to 0 in NFC_CONFIG2 Register for Read Status + * operation + */ +#define NFC_INT 0x8000 + +#define NFC_SP_EN (1 << 2) +#define NFC_ECC_EN (1 << 3) +#define NFC_INT_MSK (1 << 4) +#define NFC_BIG (1 << 5) +#define NFC_RST (1 << 6) +#define NFC_CE (1 << 7) +#define NFC_ONE_CYCLE (1 << 8) + +/* + * NFMS bit in RCSR register for pagesize of nandflash + */ +#define NFMS (*((volatile u32 *)CCM_RCSR)) +#define NFMS_BIT 30 + #endif /* __ASM_ARCH_MX31_REGS_H */ + diff --git a/include/configs/imx31_phycore.h b/include/configs/imx31_phycore.h index 1540203..44ffaf3 100644 --- a/include/configs/imx31_phycore.h +++ b/include/configs/imx31_phycore.h @@ -1,4 +1,7 @@ /* + * (C) Copyright 2008 + * Maxim Artamonov, <scn1874 at yandex.ru> + * * (C) Copyright 2004 * Texas Instruments. * Richard Woodruff r-woodruff2@ti.com @@ -34,6 +37,11 @@ #define CONFIG_MX31_HCLK_FREQ 26000000 #define CONFIG_MX31_CLK32 32000

+#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT +#endif + #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO

@@ -172,6 +180,31 @@ #define CFG_FLASH_ERASE_TOUT (100*CFG_HZ) /* Timeout for Flash Erase */ #define CFG_FLASH_WRITE_TOUT (100*CFG_HZ) /* Timeout for Flash Write */

+/*----------------------------------------------------------------------- + * NAND flash + */ + +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 +#define CFG_NAND_BASE 0x40000000 + +/* + * Because of small buffer size of NFC in iMX31, SPL has to fit into 2kB. + */ + +/*CFG_NAND_U_BOOT_OFFS and CFG_NAND_U_BOOT_SIZE must be align to full pages*/ +#define CFG_NAND_U_BOOT_OFFS 0x800 +#define CFG_NAND_U_BOOT_SIZE 0x30000 +#define CFG_NAND_U_BOOT_DST 0x87f00000 /* Load big U-Boot to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start big U-Boot from */ +#define CFG_NAND_SPL_DST CFG_NAND_U_BOOT_DST-0x40000 /* Relocate NAND_SPL to this adress*/ + +#define CFG_NAND_PAGE_SIZE 0x200 +#define CFG_NAND_BLOCK_SIZE 0x4000 +#define CFG_NAND_PAGES_PER_BLOCK 0x20 +/*for NAND_SPL*/ +#define CFG_NAND_CHIP_SIZE 0x4000000 + /* * JFFS2 partitions */ diff --git a/nand_spl/board/imx31_phycore/Makefile b/nand_spl/board/imx31_phycore/Makefile new file mode 100644 index 0000000..0aabea3 --- /dev/null +++ b/nand_spl/board/imx31_phycore/Makefile @@ -0,0 +1,95 @@ +# +# (C) Copyright 2008 +# Maxim Artamonov, <scn1874 at yandex.ru> +# +# (C) Copyright 2006-2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# (C) Copyright 2008 +# Guennadi Liakhovetki, DENX Software Engineering, lg@denx.de +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +CONFIG_NAND_SPL = y + +include $(TOPDIR)/config.mk +include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_NAND_SPL + +SOBJS = start.o lowlevel_init.o +COBJS = nand_boot_mx31.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +nandobj := $(OBJTREE)/nand_spl/ + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-aligned.bin + +all: $(obj).depend $(ALL) + +$(nandobj)u-boot-spl-aligned.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +# create symbolic links for common files + +# from cpu directory +$(obj)start.S: + @rm -f $@ + @ln -s $(TOPDIR)/cpu/arm1136/start.S $@ + +# from board directory +$(obj)lowlevel_init.S: + @rm -f $@ + @ln -s $(TOPDIR)/board/imx31_phycore/lowlevel_init.S $@ + +# from nand_spl directory +$(obj)nand_boot_mx31.c: + @rm -f $@ + @ln -s $(TOPDIR)/nand_spl/nand_boot_mx31.c $@ + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/imx31_phycore/config.mk b/nand_spl/board/imx31_phycore/config.mk new file mode 100644 index 0000000..4c271c5 --- /dev/null +++ b/nand_spl/board/imx31_phycore/config.mk @@ -0,0 +1,33 @@ +# +# (C) Copyright 2008 +# Maxim Artamonov, <scn1874 at yandex.ru> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# phyCORE-i.MX31 - PHYTEC’s phyCORE Single Board Computer module + +# TEXT_BASE for SPL: = CFG_NAND_U_BOOT_DST-0x40000 is set in board/imx31_phycore/config.mk + +# PAD_TO used to generate a 2kByte binary needed for the combined image +# -> PAD_TO = TEXT_BASE + 2048 +PAD_TO := $(shell expr $$[$(TEXT_BASE) + 2048]) + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif diff --git a/nand_spl/board/imx31_phycore/u-boot.lds b/nand_spl/board/imx31_phycore/u-boot.lds new file mode 100644 index 0000000..d25abf8 --- /dev/null +++ b/nand_spl/board/imx31_phycore/u-boot.lds @@ -0,0 +1,65 @@ +/* + * + * (C) Copyright 2008 + * Maxim Artamonov, <scn1874 at yandex.ru> + * + * January 2004 - Changed to support H4 device + * Copyright (c) 2004 Texas Instruments + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, gj@denx.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + start.o (.text) + lowlevel_init.o (.text) + nand_boot_mx31.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/nand_spl/nand_boot_mx31.c b/nand_spl/nand_boot_mx31.c new file mode 100644 index 0000000..be22d18 --- /dev/null +++ b/nand_spl/nand_boot_mx31.c @@ -0,0 +1,200 @@ +/* + * (C) Copyright 2008 + * Maxim Artamonov, <scn1874 at yandex.ru> + * + * (C) Copyright 2006-2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <nand.h> +#include <asm-arm/arch/mx31-regs.h> + +static void mx31_wait_ready(void) +{ + while (1) { + if (NFC_CONFIG2 & NFC_INT) { + NFC_CONFIG2 = NFC_CONFIG2 & (~NFC_INT);/* int flag reset */ + break; + } + } +} + +static void mx31_nand_init(void) +{ + /* unlocking RAM Buff */ + NFC_CONFIG = 0x2; + + /* hardware ECC checking and correct */ + NFC_CONFIG1 = NFC_ECC_EN; +} + +static void mx31_nand_command(unsigned short command) +{ + NFC_FLASH_CMD = command; + NFC_CONFIG2 = NFC_CMD; + mx31_wait_ready(); +} + +static void mx31_nand_page_address(unsigned int page_address) +{ + unsigned int page_count; + + NFC_FLASH_ADDR = 0x00; + NFC_CONFIG2 = NFC_ADDR; + mx31_wait_ready(); + + /* code only for 2kb flash */ + if (CFG_NAND_PAGE_SIZE == 0x800){ + NFC_FLASH_ADDR = 0x00; + NFC_CONFIG2 = NFC_ADDR; + mx31_wait_ready(); + }; + + page_count = CFG_NAND_CHIP_SIZE / CFG_NAND_PAGE_SIZE; + + if (page_address <= page_count){ + page_count--;/* transform 0x01000000 to 0x00ffffff */ + do { + NFC_FLASH_ADDR = (unsigned short)(page_address & 0xff); + NFC_CONFIG2 = NFC_ADDR; + mx31_wait_ready(); + page_address = page_address >> 8; + page_count = page_count >> 8; + } while (page_count); + } +} + +static void mx31_nand_data_output(void) +{ + int i; + + /* + * The NAND controller requires four output commands for + * large page devices. + */ + for (i = 0; i < (CFG_NAND_PAGE_SIZE / 512); i++) { + NFC_CONFIG1 = NFC_ECC_EN; + NFC_BUF_ADDR = i; /* read in i:th buffer */ + NFC_CONFIG2 = NFC_OUTPUT; + mx31_wait_ready(); + } +} + +static int mx31_nand_check_ecc(void) +{ + unsigned short ecc_status_registr; + + ecc_status_registr = NFC_ECC_STATUS_RESULT; + + if (ecc_status_registr != 0) + return 1;/* error */ + return 0; +} + +static int mx31_read_page(unsigned int page_address, unsigned char *buf) +{ + int i; + volatile u32 *p1, *p2, a; + + mx31_nand_init (); + NFC_BUF_ADDR = 0; /* read in first 0 buffer */ + mx31_nand_command (NAND_CMD_READ0); + mx31_nand_page_address (page_address); + + if (CFG_NAND_CHIP_SIZE >= 0x08000000) + mx31_nand_command (NAND_CMD_READSTART); + + mx31_nand_data_output ();/* fill the main buffer 0 */ + + if (mx31_nand_check_ecc ()) + while (1) { + /* hang-loop in case of ecc-error */ + } + + p1 = (u32 *)MAIN_AREA0; + p2 = (u32 *)buf; + + /* main copy loop from NAND-buffer to SDRAM memory */ + for (i=0; i < (CFG_NAND_PAGE_SIZE / 4); i++) { + *p2 = *p1; + p1++; + p2++; + } + + p1 = (u32 *)SPARE_AREA0; + + /* it is hardware specific code for 8-bit 512 B NAND-flash spare area */ + p1++; + a = *p1; + a = (a & 0x0000ff00) >> 8; + + if (a != 0xff) /* bad block marker verify */ + return 1;/* potential bad block */ + + return 0; +} + +static int nand_load(unsigned int from, unsigned int size, unsigned char *buf) +{ + int i, bb; + + mx31_nand_init (); + + /* convert from to page number */ + from = from / CFG_NAND_PAGE_SIZE; + + i = 0; + + while (i < (size/CFG_NAND_PAGE_SIZE)) { + + if ((from*CFG_NAND_PAGE_SIZE) >= CFG_NAND_CHIP_SIZE) + return 2;/* memory segment violation */ + + bb = mx31_read_page (from, buf); + + /* checking first page of each block */ + /* if this page has bb marker, then skip whole block */ + if ((!(from % CFG_NAND_PAGES_PER_BLOCK)) && bb) { + from = from + CFG_NAND_PAGES_PER_BLOCK; + } + else { + i++; + from++; + buf = buf + CFG_NAND_PAGE_SIZE; + } + } + return 0; +} + +/* + * The main entry for NAND booting. It's necessary that SDRAM is already + * configured and available since this code loads the main U-Boot image + * from NAND into SDRAM and starts it from there. + */ +void nand_boot(void) +{ + __attribute__((noreturn)) void (*uboot)(void); + + /* CFG_NAND_U_BOOT_OFFS and CFG_NAND_U_BOOT_SIZE must */ + /* be align to full pages */ + nand_load (CFG_NAND_U_BOOT_OFFS, CFG_NAND_U_BOOT_SIZE, \ + (uchar *)CFG_NAND_U_BOOT_DST); + + uboot = (void *)CFG_NAND_U_BOOT_START; + uboot (); +}