Dear Atul Kumar,

Please CC the mailing list, always.

Dear Marek,

     Thanks for your attention.. After doing "coninfo", i get below

msg..

OMAP3 beagleboard.org #

coninfo

List of available devices:

serial 80000003 SIO stdin stdout stderr

usbtty 00000

003 .IO

usbkbd 80000001 SI.

OMAP3 beagleboard.org #

tried to do setenv...

OMAP3 beagleboard.org #

setenv stdin usbkbd

All right, maybe you should fix your method of pasting u-boot output, you have every second line blank and a few linebreaks here and there, randomly. It'd be cool to fix it, it'd make it much easier to read. Can you do something about it please?

OMAP3 beagleboard.org #

After doing this my terminal does not prints any logs but i am able to type on console..

You mean with the keyboard? Because "setenv stdin usbkbd" tells the system to read input from the USB keyboard.

Once when i reboot the board again the logs starts coming up..

Ah ... so you got no console output. Try typing on the usb keyboard. If you change stdin to usbkbd, you'd only be able to type with the USB keyboard, it won't pick input from the UART/serial port or whatever other source you use.

I see on "*stdin name- *serial** " .. if instead of serial "*usbkbd*" is there it will be able to register the kbd..

I tried this another way but do not find any change in pri ..

Pri? [...]

btw it's a good practice in the mailing list to not top-post (aka reply under the email you're replying to). But if you comment on stuff, you can do it in the middle of the email (just like I did with this one) to better identify what you're replying to.

Thanks & Regards Atul Kumar 9845495793

On Fri, May 11, 2012 at 4:25 PM, Marek Vasut marex@denx.de wrote:

...

Dear Atul Kumar,

...

Dear Marek,

     I am tring to bring up USB Keyboard on u-boot with
     "Beagle_board

xM ver B".. found number of post,but the stack is already updated one.. I am able to find the info of the connected device but some how keyboard does not works.. can you suggest/guide me were i am making mistake or where I need to do some device specific changes..

Please always CC the U-Boot mailing list (CCed).

Did you try running "coninfo" after the "usb reset"/"usb start"? What does it output, do you see "usbkbd" there? Wild guess would be to run "setenv stdin usbkbd" or something after you do "usb reset".

...

*logs for "usb start"*

OMAP3 beagleboard.org #

usb start

(Re)start USB...

USB: Initializing OMAP EHCI

OMAP UHH_REV

ISION 0x10

OMAP EHCI init done

Register 1313 NbrPorts 3

USB EHCI 1.00

scanning bus for devices...

4 USB Device(s) found

USB KBD: found set protocol...

USB KBD: found set idle...

USB

KBD: enable interrupt pipe...

USB KBD: found set up device.

USB KBD: register.

usb_kbd_dev.name- usbkbd

before stdio register

clone _dev->name-usbkbd,dev->name-usbkbd

in stdio register,usb_kbd_dev.name- usbkbd

After stdio register

before strcmp

stdin name- *serial*

scan end

scanning bus for storage devices... 0 Storage Device(s) found

scanning bus for ethernet devices... Warning: failed to set MAC address

1 Ethernet Device(s) found

OMAP3 beagleboard.org #

*logs for "usb info"*

OMAP3 beagleboard.org #

usb info

1: Hub, USB Revision 2.0

• u-boot EHCI Host Controller

• Class: Hub

• PacketSize: 64 Configurations: 1

Vendor: 0x0000 Product 0x0000 Version 1.0

Configuration: 1

• Interfaces: 1 Self Powered 0mA

Interface: 0

• Alternate Setting 0, Endpoints: 1

• Class Hub

• Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Hub, USB Revision 2.0

• Class: Hub

• PacketSize: 64 Configurations: 1

• Vendor: 0x0424 Product 0x9514 Version 2.0

Configuration: 1

• Interfaces: 1 Self Powered Remote Wakeup 2mA

Interface: 0

• Alternate Setting 0, Endpoints: 1

• Class Hub

• Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms

• Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms

3: Vendor specific, USB Revision 2.0

• Class: Vendor specific

• PacketSize: 64 Configurations: 1

• Vendor: 0x0424 Product 0xec00 Version 2.0

Configuration: 1

• Interfaces: 1 Self Powered Remote Wakeup 2mA

Interface: 0

• Alternate Setting 0, Endpoints: 3

• Class Vendor specific

• Endpoint 1 In Bulk MaxPacket 512

• Endpoint 2 Out Bulk MaxPacket 512

• Endpoint 3 In Interrupt MaxPacket 16 Interval 4ms

4: Human Interface, USB Revision 1.10

• LITEON Technology USB Multimedia Keyboard

• Class: (from Interface) Human Interface

• PacketSize: 8 Configurations: 1

• Vendor: 0x046d Product 0xc312 Version 1.1

Configuration: 1

• Interfaces: 1 Bus Powered Remote Wakeup 70mA

Interface: 0

• Alternate Setting 0, Endpoints: 1

• Class Human Interface, Subclass: Boot Keyboard

• Endpoint 1 In Interrupt MaxPacket 8 Interval 24ms

OMAP3 beagleboard.org #

Thanks & Regards Atul Kumar 9845495793