From: York Sun yorksun@freescale.com

B4860QDS is a high-performance computing evaluation, development and test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview ------------------ - DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 4 GB of memory in two ranks of 2 GB. - DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank. - SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point 16x16 switch VSC3316 - SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point 8x8 switch VSC3308 - USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode. - B4860 UART port is available over USB-to-UART translator USB2SER or over RS232 flat cable. - A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA connector ports 0 and 2 for AMC mode. - The B4860 configuration may be loaded from nine bits coded reset configuration reset source. The RCW source is set by appropriate DIP-switches: - 16-bit NOR Flash / PROMJet - QIXIS 8-bit NOR Flash Emulator - 8-bit NAND Flash - 24-bit SPI Flash - Long address I2C EEPROM - Available debug interfaces are: - On-board eCWTAP controller with ETH and USB I/F - JTAG/COP 16-pin header for any external TAP controller - External JTAG source over AMC to support B2B configuration - 70-pin Aurora debug connector - QIXIS (FPGA) logic: - 2 KB internal memory space including - IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK, DDRCLK1, 2 and RTCCLK. - Two 8T49N222A SerDes ref clock devices support two SerDes port clocks - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun yorksun@freescale.com Signed-off-by: Prabhakar Kushwaha prabhakar@freescale.com Signed-off-by: Shaveta Leekha shaveta@freescale.com Signed-off-by: Priyanka Jain Priyanka.Jain@freescale.com Signed-off-by: Poonam Aggrwal poonam.aggrwal@freescale.com Signed-off-by: Roy Zang tie-fei.zang@freescale.com Signed-off-by: Sandeep Singh Sandeep@freescale.com --- board/freescale/b4860qds/Makefile | 54 ++ board/freescale/b4860qds/b4860qds.c | 458 ++++++++++++ board/freescale/b4860qds/b4860qds.h | 26 + board/freescale/b4860qds/b4860qds_crossbar_con.h | 67 ++ board/freescale/b4860qds/b4860qds_qixis.h | 37 + board/freescale/b4860qds/ddr.c | 190 +++++ board/freescale/b4860qds/eth_b4860qds.c | 338 +++++++++ board/freescale/b4860qds/law.c | 44 ++ board/freescale/b4860qds/pci.c | 39 + board/freescale/b4860qds/tlb.c | 127 ++++ boards.cfg | 6 + doc/README.b4860qds | 330 +++++++++ include/configs/B4860QDS.h | 820 ++++++++++++++++++++++ 13 files changed, 2536 insertions(+), 0 deletions(-) create mode 100644 board/freescale/b4860qds/Makefile create mode 100644 board/freescale/b4860qds/b4860qds.c create mode 100644 board/freescale/b4860qds/b4860qds.h create mode 100644 board/freescale/b4860qds/b4860qds_crossbar_con.h create mode 100644 board/freescale/b4860qds/b4860qds_qixis.h create mode 100644 board/freescale/b4860qds/ddr.c create mode 100644 board/freescale/b4860qds/eth_b4860qds.c create mode 100644 board/freescale/b4860qds/law.c create mode 100644 board/freescale/b4860qds/pci.c create mode 100644 board/freescale/b4860qds/tlb.c create mode 100644 doc/README.b4860qds create mode 100644 include/configs/B4860QDS.h

diff --git a/board/freescale/b4860qds/Makefile b/board/freescale/b4860qds/Makefile new file mode 100644 index 0000000..06018f4 --- /dev/null +++ b/board/freescale/b4860qds/Makefile @@ -0,0 +1,54 @@ +# +# Copyright 2012 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-$(CONFIG_B4860QDS)+= eth_b4860qds.o +COBJS-$(CONFIG_PCI) += pci.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c new file mode 100644 index 0000000..88bdc1f --- /dev/null +++ b/board/freescale/b4860qds/b4860qds.c @@ -0,0 +1,458 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> + +#include "../common/qixis.h" +#include "../common/vsc3316_3308.h" +#include "b4860qds.h" +#include "b4860qds_qixis.h" +#include "b4860qds_crossbar_con.h" + +#define CLK_MUX_SEL_MASK 0x4 +#define ETH_PHY_CLK_OUT 0x4 + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + char buf[64]; + u8 sw; + struct cpu_type *cpu = gd->cpu; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + unsigned int i; + static const char *const freq[] = {"100", "125", "156.25", "161.13", + "122.88", "122.88", "122.88"}; + int clock; + + printf("Board: %sQDS, ", cpu->name); + printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ", + QIXIS_READ(id), QIXIS_READ(arch)); + + sw = QIXIS_READ(brdcfg[0]); + sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + if (sw < 0x8) + printf("vBank: %d\n", sw); + else if (sw >= 0x8 && sw <= 0xE) + puts("NAND\n"); + else + printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); + + printf("FPGA: v%d (%s), build %d", + (int)QIXIS_READ(scver), qixis_read_tag(buf), + (int)qixis_read_minor()); + /* the timestamp string contains "\n" at the end */ + printf(" on %s", qixis_read_time(buf)); + + /* Display the RCW, so that no one gets confused as to what RCW + * we're actually using for this boot. + */ + puts("Reset Configuration Word (RCW):"); + for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) { + u32 rcw = in_be32(&gur->rcwsr[i]); + + if ((i % 4) == 0) + printf("\n %08x:", i * 4); + printf(" %08x", rcw); + } + puts("\n"); + + /* + * Display the actual SERDES reference clocks as configured by the + * dip switches on the board. Note that the SWx registers could + * technically be set to force the reference clocks to match the + * values that the SERDES expects (or vice versa). For now, however, + * we just display both values and hope the user notices when they + * don't match. + */ + puts("SERDES Reference Clocks: "); + sw = QIXIS_READ(brdcfg[2]); + clock = (sw >> 5) & 7; + printf("Bank1=%sMHz ", freq[clock]); + sw = QIXIS_READ(brdcfg[4]); + clock = (sw >> 6) & 3; + printf("Bank2=%sMHz\n", freq[clock]); + + return 0; +} + +int select_i2c_ch_pca(u8 ch) +{ + int ret; + + /* Selecting proper channel via PCA*/ + ret = i2c_write(I2C_MUX_PCA_ADDR, 0x0, 1, &ch, 1); + if (ret) { + printf("PCA: failed to select proper channel.\n"); + return ret; + } + + return 0; +} + +int configure_vsc3316_3308(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + unsigned int num_vsc16_con, num_vsc08_con; + u32 serdes1_prtcl, serdes2_prtcl; + int ret; + + serdes1_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + if (!serdes1_prtcl) { + printf("SERDES1 is not enabled\n"); + return 0; + } + serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl); + + serdes2_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + if (!serdes2_prtcl) { + printf("SERDES2 is not enabled\n"); + return 0; + } + serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl); + + switch (serdes1_prtcl) { + case 0x2a: + case 0x2C: + case 0x2D: + case 0x2E: + /* + * Configuration: + * SERDES: 1 + * Lanes: A,B: SGMII + * Lanes: C,D,E,F,G,H: CPRI + */ + debug("Configuring crossbar to use onboard SGMII PHYs:" + "srds_prctl:%x\n", serdes1_prtcl); + num_vsc16_con = NUM_CON_VSC3316; + /* Configure VSC3316 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3316); + if (!ret) { + ret = vsc3316_config(VSC3316_TX_ADDRESS, + vsc16_tx_sgmii_lane_ab, num_vsc16_con); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_RX_ADDRESS, + vsc16_rx_sgmii_lane_ab, num_vsc16_con); + if (ret) + return ret; + } else { + return ret; + } + break; + +#ifdef CONFIG_PPC_B4420 + case 0x18: + /* + * Configuration: + * SERDES: 1 + * Lanes: A,B,C,D: SGMII + * Lanes: E,F,G,H: CPRI + */ + debug("Configuring crossbar to use onboard SGMII PHYs:" + "srds_prctl:%x\n", serdes1_prtcl); + num_vsc16_con = NUM_CON_VSC3316; + /* Configure VSC3316 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3316); + if (!ret) { + ret = vsc3316_config(VSC3316_TX_ADDRESS, + vsc16_tx_sgmii_lane_cd, num_vsc16_con); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_RX_ADDRESS, + vsc16_rx_sgmii_lane_cd, num_vsc16_con); + if (ret) + return ret; + } else { + return ret; + } + break; +#endif + + case 0x3E: + case 0x0D: + case 0x0E: + case 0x12: + num_vsc16_con = NUM_CON_VSC3316; + /* Configure VSC3316 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3316); + if (!ret) { + ret = vsc3316_config(VSC3316_TX_ADDRESS, + vsc16_tx_sfp, num_vsc16_con); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_RX_ADDRESS, + vsc16_rx_sfp, num_vsc16_con); + if (ret) + return ret; + } else { + return ret; + } + break; + default: + printf("WARNING:VSC crossbars programming not supported for:%x" + " SerDes1 Protocol.\n", serdes1_prtcl); + return -1; + } + + switch (serdes2_prtcl) { + case 0x9E: + case 0x9A: + case 0x98: + case 0xb2: + case 0x49: + case 0x4E: + case 0x8D: + case 0x7A: + num_vsc08_con = NUM_CON_VSC3308; + /* Configure VSC3308 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3308); + if (!ret) { + ret = vsc3308_config(VSC3308_TX_ADDRESS, + vsc08_tx_amc, num_vsc08_con); + if (ret) + return ret; + ret = vsc3308_config(VSC3308_RX_ADDRESS, + vsc08_rx_amc, num_vsc08_con); + if (ret) + return ret; + } else { + return ret; + } + break; + default: + printf("WARNING:VSC crossbars programming not supported for: %x" + " SerDes2 Protocol.\n", serdes2_prtcl); + return -1; + } + + return 0; +} + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + /* Configure VSC3316 and VSC3308 crossbar switches */ + if (configure_vsc3316_3308()) + printf("VSC:failed to configure VSC3316/3308.\n"); + else + printf("VSC:VSC3316/3308 successfully configured.\n"); + + select_i2c_ch_pca(I2C_CH_DEFAULT); + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch ((sysclk_conf & 0x0C) >> 2) { + case QIXIS_CLK_100: + return 100000000; + case QIXIS_CLK_125: + return 125000000; + case QIXIS_CLK_133: + return 133333333; + } + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + switch (ddrclk_conf & 0x03) { + case QIXIS_CLK_100: + return 100000000; + case QIXIS_CLK_125: + return 125000000; + case QIXIS_CLK_133: + return 133333333; + } + return 66666666; +} + +static int serdes_refclock(u8 sw, u8 sdclk) +{ + unsigned int clock; + int ret = -1; + u8 brdcfg4; + + if (sdclk == 1) { + brdcfg4 = QIXIS_READ(brdcfg[4]); + if ((brdcfg4 & CLK_MUX_SEL_MASK) == ETH_PHY_CLK_OUT) + return SRDS_PLLCR0_RFCK_SEL_125; + else + clock = (sw >> 5) & 7; + } else + clock = (sw >> 6) & 3; + + switch (clock) { + case 0: + ret = SRDS_PLLCR0_RFCK_SEL_100; + break; + case 1: + ret = SRDS_PLLCR0_RFCK_SEL_125; + break; + case 2: + ret = SRDS_PLLCR0_RFCK_SEL_156_25; + break; + case 3: + ret = SRDS_PLLCR0_RFCK_SEL_161_13; + break; + case 4: + case 5: + case 6: + ret = SRDS_PLLCR0_RFCK_SEL_122_88; + break; + default: + ret = -1; + break; + } + + return ret; +} + +static const char *serdes_clock_to_string(u32 clock) +{ + switch (clock) { + case SRDS_PLLCR0_RFCK_SEL_100: + return "100"; + case SRDS_PLLCR0_RFCK_SEL_125: + return "125"; + case SRDS_PLLCR0_RFCK_SEL_156_25: + return "156.25"; + case SRDS_PLLCR0_RFCK_SEL_161_13: + return "161.13"; + default: + return "122.88"; + } +} + +#define NUM_SRDS_BANKS 2 + +int misc_init_r(void) +{ + u8 sw; + serdes_corenet_t *srds_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 actual[NUM_SRDS_BANKS]; + unsigned int i; + int clock; + + sw = QIXIS_READ(brdcfg[2]); + clock = serdes_refclock(sw, 1); + if (clock >= 0) + actual[0] = clock; + else + printf("Warning: SDREFCLK1 switch setting is unsupported\n"); + + sw = QIXIS_READ(brdcfg[4]); + clock = serdes_refclock(sw, 2); + if (clock >= 0) + actual[1] = clock; + else + printf("Warning: SDREFCLK2 switch setting unsupported\n"); + + for (i = 0; i < NUM_SRDS_BANKS; i++) { + u32 pllcr0 = srds_regs->bank[i].pllcr0; + u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; + if (expected != actual[i]) { + printf("Warning: SERDES bank %u expects reference clock" + " %sMHz, but actual is %sMHz\n", i + 1, + serdes_clock_to_string(expected), + serdes_clock_to_string(actual[i])); + } + } + + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif +} diff --git a/board/freescale/b4860qds/b4860qds.h b/board/freescale/b4860qds/b4860qds.h new file mode 100644 index 0000000..f290f3c --- /dev/null +++ b/board/freescale/b4860qds/b4860qds.h @@ -0,0 +1,26 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CORENET_DS_H__ +#define __CORENET_DS_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/b4860qds/b4860qds_crossbar_con.h b/board/freescale/b4860qds/b4860qds_crossbar_con.h new file mode 100644 index 0000000..994dec5 --- /dev/null +++ b/board/freescale/b4860qds/b4860qds_crossbar_con.h @@ -0,0 +1,67 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CROSSBAR_CONNECTIONS_H__ +#define __CROSSBAR_CONNECTIONS_H__ + +#define NUM_CON_VSC3316 8 +#define NUM_CON_VSC3308 4 + +static const int8_t vsc16_tx_amc[8][2] = { {15, 3}, {0, 2}, {7, 4}, {9, 10}, + {5, 11}, {4, 5}, {2, 6}, {12, 9} }; + +static const int8_t vsc16_tx_sfp[8][2] = { {15, 8}, {0, 0}, {7, 7}, {9, 1}, + {5, 15}, {4, 14}, {2, 12}, {12, 13} }; + +static const int8_t vsc16_tx_sgmii_lane_ab[8][2] = { {2, 14}, {12, 15}, + {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; + +#ifdef CONFIG_PPC_B4420 +static const int8_t vsc16_tx_sgmii_lane_cd[8][2] = { {5, 14}, {4, 15}, + {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; +#endif +static const int8_t vsc16_tx_aurora[8][2] = { {2, 13}, {12, 12}, {-1, -1}, + {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; + +static const int8_t vsc16_rx_amc[8][2] = { {3, 15}, {2, 1}, {4, 8}, {10, 9}, + {11, 11}, {5, 10}, {6, 3}, {9, 12} }; + +static const int8_t vsc16_rx_sfp[8][2] = { {0, 15}, {8, 1}, {1, 8}, {7, 9}, + {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; + +static const int8_t vsc16_rx_sgmii_lane_ab[8][2] = { {14, 3}, {15, 12}, + {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; + +#ifdef CONFIG_PPC_B4420 +static const int8_t vsc16_rx_sgmii_lane_cd[8][2] = { {14, 11}, {15, 10}, + {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; +#endif + +static const int8_t vsc16_rx_aurora[8][2] = { {12, 3}, {13, 12}, {-1, -1}, + {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; + +static const int8_t vsc08_tx_amc[4][2] = { {2, 2}, {3, 3}, {7, 4}, {1, 5} }; + +static const int8_t vsc08_tx_sfp[4][2] = { {2, 6}, {3, 7}, {7, 1}, {1, 0} }; + +static const int8_t vsc08_rx_amc[4][2] = { {2, 3}, {3, 4}, {4, 7}, {5, 1} }; + +static const int8_t vsc08_rx_sfp[4][2] = { {6, 3}, {7, 4}, {1, 7}, {0, 1} }; + +#endif diff --git a/board/freescale/b4860qds/b4860qds_qixis.h b/board/freescale/b4860qds/b4860qds_qixis.h new file mode 100644 index 0000000..575b2ae --- /dev/null +++ b/board/freescale/b4860qds/b4860qds_qixis.h @@ -0,0 +1,37 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __B4860QDS_QIXIS_H__ +#define __B4860QDS_QIXIS_H__ + +/* Definitions of QIXIS Registers for B4860QDS */ + +/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ +#define BRDCFG4_EMISEL_MASK 0xE0 +#define BRDCFG4_EMISEL_SHIFT 5 + +/* CLK */ +#define QIXIS_CLK_66 0x0 +#define QIXIS_CLK_100 0x1 +#define QIXIS_CLK_125 0x2 +#define QIXIS_CLK_133 0x3 + +#define QIXIS_SRDS1CLK_122 0x5a +#define QIXIS_SRDS1CLK_125 0x5e +#endif diff --git a/board/freescale/b4860qds/ddr.c b/board/freescale/b4860qds/ddr.c new file mode 100644 index 0000000..dd4c0f6 --- /dev/null +++ b/board/freescale/b4860qds/ddr.c @@ -0,0 +1,190 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 or later as published by the Free Software Foundation. + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + +dimm_params_t ddr_raw_timing = { + .n_ranks = 2, + .rank_density = 2147483648u, + .capacity = 4294967296u, + .primary_sdram_width = 64, + .ec_sdram_width = 8, + .registered_dimm = 0, + .mirrored_dimm = 1, + .n_row_addr = 15, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 2, /* ECC */ + .burst_lengths_bitmask = 0x0c, + + .tCKmin_X_ps = 1071, + .caslat_X = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */ + .tAA_ps = 13910, + .tWR_ps = 15000, + .tRCD_ps = 13910, + .tRRD_ps = 6000, + .tRP_ps = 13910, + .tRAS_ps = 34000, + .tRC_ps = 48910, + .tRFC_ps = 260000, + .tWTR_ps = 7500, + .tRTP_ps = 7500, + .refresh_rate_ps = 7800000, + .tFAW_ps = 35000, +}; + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "RAW timing DDR"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; + u32 cpo; + u32 write_data_delay; + u32 force_2T; +}; + +/* + * This table contains all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T + * ranks| mhz|adjst| start | ctl2 | ctl3 | |delay | + */ + {2, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0}, + {2, 1666, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0}, + {2, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0}, + {1, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0}, + {1, 1700, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0}, + {1, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 2) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + + /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->cpo_override = pbsp->cpo; + popts->write_data_delay = + pbsp->write_data_delay; + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twoT_en = pbsp->force_2T; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found " + "for data rate %lu MT/s\n" + "Trying to use the highest speed (%u) parameters\n", + ddr_freq, pbsp_highest->datarate_mhz_high); + popts->cpo_override = pbsp_highest->cpo; + popts->write_data_delay = pbsp_highest->write_data_delay; + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->twoT_en = pbsp_highest->force_2T; + } else { + panic("DIMM is not supported by this board"); + } +found: + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c new file mode 100644 index 0000000..68e2725 --- /dev/null +++ b/board/freescale/b4860qds/eth_b4860qds.c @@ -0,0 +1,338 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * Author: Sandeep Kumar Singh sandeep@freescale.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* This file is based on board/freescale/corenet_ds/eth_superhydra.c */ + +/* + * This file handles the board muxing between the Fman Ethernet MACs and + * the RGMII/SGMII/XGMII PHYs on a Freescale B4860 "Centaur". The SGMII + * PHYs are the two on-board 1Gb ports. There are no RGMII PHY on board. + * The 10Gb XGMII PHY is provided via the XAUI riser card. There is only + * one Fman device on B4860. The SERDES configuration is used to determine + * where the SGMII and XAUI cards exist, and also which Fman MACs are routed + * to which PHYs. So for a given Fman MAC, there is one and only PHY it + * connects to. MACs cannot be routed to PHYs dynamically. This configuration + * is done at boot time by reading SERDES protocol from RCW. + */ + +#include <common.h> +#include <netdev.h> +#include <asm/fsl_serdes.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <malloc.h> +#include <fdt_support.h> +#include <asm/fsl_dtsec.h> + +#include "../common/ngpixis.h" +#include "../common/fman.h" +#include "../common/qixis.h" +#include "b4860qds_qixis.h" + +#define EMI_NONE 0xFFFFFFFF + +#ifdef CONFIG_FMAN_ENET + +/* + * Mapping of all 16 SERDES lanes to board slots. A value n(>0) will mean that + * lane at index is mapped to slot number n. A value of '0' will mean + * that the mapping must be determined dynamically, or that the lane maps to + * something other than a board slot + */ +static u8 lane_to_slot[] = { + 0, 0, 0, 0, + 0, 0, 0, 0, + 1, 1, 1, 1, + 0, 0, 0, 0 +}; + +/* + * This function initializes the lane_to_slot[] array. It reads RCW to check + * if Serdes2{E,F,G,H} is configured as slot 2 or as SFP and initializes + * lane_to_slot[] accordingly + */ +static void initialize_lane_to_slot(void) +{ + unsigned int serdes2_prtcl; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + serdes2_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + debug("Initializing lane to slot: Serdes2 protocol: %x\n", + serdes2_prtcl); + + switch (serdes2_prtcl) { + case 0x18: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B,C,D: SGMII + * Lanes: E,F: Aur + * Lanes: G,H: SRIO + */ + case 0x91: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B: SGMII + * Lanes: C,D: SRIO2 + * Lanes: E,F,G,H: XAUI2 + */ + case 0x93: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B,C,D: SGMII + * Lanes: E,F,G,H: XAUI2 + */ + case 0x98: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B,C,D: XAUI2 + * Lanes: E,F,G,H: XAUI2 + */ + case 0x9a: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B: PCI + * Lanes: C,D: SGMII + * Lanes: E,F,G,H: XAUI2 + */ + case 0x9e: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B,C,D: PCI + * Lanes: E,F,G,H: XAUI2 + */ + case 0xb2: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B,C,D: PCI + * Lanes: E,F: SGMII 3&4 + * Lanes: G,H: XFI + */ + case 0xc2: + /* + * Configuration: + * SERDES: 2 + * Lanes: A,B: SGMII + * Lanes: C,D: SRIO2 + * Lanes: E,F,G,H: XAUI2 + */ + lane_to_slot[12] = 2; + lane_to_slot[13] = lane_to_slot[12]; + lane_to_slot[14] = lane_to_slot[12]; + lane_to_slot[15] = lane_to_slot[12]; + break; + + default: + printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n", + serdes2_prtcl); + break; + } + return; +} + +#endif /* #ifdef CONFIG_FMAN_ENET */ + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_FMAN_ENET + struct memac_mdio_info memac_mdio_info; + struct memac_mdio_info tg_memac_mdio_info; + unsigned int i; + unsigned int serdes1_prtcl, serdes2_prtcl; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + serdes1_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + if (!serdes1_prtcl) { + printf("SERDES1 is not enabled\n"); + return 0; + } + serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl); + + serdes2_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + if (!serdes2_prtcl) { + printf("SERDES2 is not enabled\n"); + return 0; + } + serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl); + + printf("Initializing Fman\n"); + + initialize_lane_to_slot(); + + memac_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + memac_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the real 1G MDIO bus */ + fm_memac_mdio_init(bis, &memac_mdio_info); + + tg_memac_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; + tg_memac_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; + + /* Register the real 10G MDIO bus */ + fm_memac_mdio_init(bis, &tg_memac_mdio_info); + + /* + * Program the two on board DTSEC PHY addresses assuming that they are + * all SGMII. RGMII is not supported on this board. Setting SGMII 5 and + * 6 to on board SGMII phys + */ + fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + + switch (serdes1_prtcl) { + case 0x2a: + /* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */ + debug("Setting phy addresses for FM1_DTSEC5: %x and" + "FM1_DTSEC6: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR, + CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + /* Fixing Serdes clock by programming FPGA register */ + QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125); + fm_info_set_phy_address(FM1_DTSEC5, + CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC6, + CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + break; +#ifdef CONFIG_PPC_B4420 + case 0x18: + /* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */ + debug("Setting phy addresses for FM1_DTSEC3: %x and" + "FM1_DTSEC4: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR, + CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + /* Fixing Serdes clock by programming FPGA register */ + QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125); + fm_info_set_phy_address(FM1_DTSEC3, + CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, + CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); + break; +#endif + default: + printf("Fman: Unsupported SerDes1 Protocol 0x%02x\n", + serdes1_prtcl); + break; + } + switch (serdes2_prtcl) { + case 0x18: + debug("Setting phy addresses on SGMII Riser card for" + "FM1_DTSEC ports: \n"); + fm_info_set_phy_address(FM1_DTSEC1, + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, + CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC3, + CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, + CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR); + break; + case 0x49: + debug("Setting phy addresses on SGMII Riser card for" + "FM1_DTSEC ports: \n"); + fm_info_set_phy_address(FM1_DTSEC1, + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, + CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC3, + CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR); + break; + case 0x8d: + case 0xb2: + debug("Setting phy addresses on SGMII Riser card for" + "FM1_DTSEC ports: \n"); + fm_info_set_phy_address(FM1_DTSEC3, + CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, + CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); + break; + default: + printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n", + serdes2_prtcl); + break; + } + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + int idx = i - FM1_DTSEC1; + + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_SGMII: + fm_info_set_mdio(i, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + break; + case PHY_INTERFACE_MODE_NONE: + fm_info_set_phy_address(i, 0); + break; + default: + printf("Fman1: DTSEC%u set to unknown interface %i\n", + idx + 1, fm_info_get_enet_if(i)); + fm_info_set_phy_address(i, 0); + break; + } + } + + cpu_eth_init(bis); +#endif + + return pci_eth_init(bis); +} + +void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, + enum fm_port port, int offset) +{ + int phy; + char alias[32]; + + if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) { + phy = fm_info_get_phy_address(port); + + sprintf(alias, "phy_sgmii_%x", phy); + fdt_set_phy_handle(fdt, compat, addr, alias); + } +} + +void fdt_fixup_board_enet(void *fdt) +{ + int i; + char alias[32]; + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_NONE: + sprintf(alias, "ethernet%u", i); + fdt_status_disabled_by_alias(fdt, alias); + break; + default: + break; + } + } +} diff --git a/board/freescale/b4860qds/law.c b/board/freescale/b4860qds/law.c new file mode 100644 index 0000000..4142e01 --- /dev/null +++ b/board/freescale/b4860qds/law.c @@ -0,0 +1,44 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif + SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/b4860qds/pci.c b/board/freescale/b4860qds/pci.c new file mode 100644 index 0000000..b130d13 --- /dev/null +++ b/board/freescale/b4860qds/pci.c @@ -0,0 +1,39 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/b4860qds/tlb.c b/board/freescale/b4860qds/tlb.c new file mode 100644 index 0000000..373cb78 --- /dev/null +++ b/board/freescale/b4860qds/tlb.c @@ -0,0 +1,127 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the + * SRAM is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000, + CONFIG_SYS_PCIE1_MEM_PHYS + 0x10000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_64K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 6, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 8, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_64K, 1), +#endif + SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_4K, 1), + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 35f38f3..6e84c3a 100644 --- a/boards.cfg +++ b/boards.cfg @@ -858,6 +858,12 @@ stxssa_4M powerpc mpc85xx stxssa stx T4240QDS powerpc mpc85xx t4qds freescale T4240QDS_SDCARD powerpc mpc85xx t4qds freescale - T4240QDS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 T4240QDS_SPIFLASH powerpc mpc85xx t4qds freescale - T4240QDS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +B4860QDS powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4860 +B4860QDS_NAND powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4860,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 +B4860QDS_SPIFLASH powerpc mpc85xx b4860qds freescale - B4860QDS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +B4420QDS powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420 +B4420QDS_NAND powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 +B4420QDS_SPIFLASH powerpc mpc85xx b4860qds freescale - B4860QDS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 xpedite520x powerpc mpc85xx - xes xpedite537x powerpc mpc85xx - xes xpedite550x powerpc mpc85xx - xes diff --git a/doc/README.b4860qds b/doc/README.b4860qds new file mode 100644 index 0000000..f6c5ff8 --- /dev/null +++ b/doc/README.b4860qds @@ -0,0 +1,330 @@ +Overview +-------- +The B4860QDS is a Freescale reference board that hosts the B4860 SoC (and variants). + +B4860 Overview +------------- +The B4860 QorIQ Qonverge device is a Freescale high-end, multicore SoC based on +StarCore and Power Architecture® cores. It targets the broadband wireless +infrastructure and builds upon the proven success of the existing multicore +DSPs and Power CPUs. It is designed to bolster the rapidly changing and +expanding wireless markets, such as 3GLTE (FDD and TDD), LTE-Advanced, and UMTS. + +The B4860 is a highly-integrated StarCore and Power Architecture processor that +contains: +. Six fully-programmable StarCore SC3900 FVP subsystems, divided into three +clusters-each core runs up to 1.2 GHz, with an architecture highly optimized for +wireless base station applications +. Four dual-thread e6500 Power Architecture processors organized in one cluster-each +core runs up to 1.8 GHz +. Two DDR3/3L controllers for high-speed, industry-standard memory interface each +runs at up to 1866.67 MHz +. MAPLE-B3 hardware acceleration-for forward error correction schemes including +Turbo or Viterbi decoding, Turbo encoding and rate matching, MIMO MMSE +equalization scheme, matrix operations, CRC insertion and check, DFT/iDFT and +FFT/iFFT calculations, PUSCH/PDSCH acceleration, and UMTS chip rate +acceleration +. CoreNet fabric that fully supports coherency using MESI protocol between the + e6500 cores, SC3900 FVP cores, memories and external interfaces. + CoreNet fabric interconnect runs at 667 MHz and supports coherent and + non-coherent out of order transactions with prioritization and bandwidth + allocation amongst CoreNet endpoints. +. Data Path Acceleration Architecture, which includes the following: +. Frame Manager (FMan), which supports in-line packet parsing and general + classification to enable policing and QoS-based packet distribution +. Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading + of queue management, task management, load distribution, flow ordering, buffer + management, and allocation tasks from the cores +. Security engine (SEC 5.3)-crypto-acceleration for protocols such as IPsec, + SSL, and 802.16 +. RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and + outbound). Supports types 5, 6 (outbound only) +. Large internal cache memory with snooping and stashing capabilities for + bandwidth saving and high utilization of processor elements. The 9856-Kbyte + internal memory space includes the following: +. 32 Kbyte L1 ICache per e6500/SC3900 core +. 32 Kbyte L1 DCache per e6500/SC3900 core +. 2048 Kbyte unified L2 cache for each SC3900 FVP cluster +. 2048 Kbyte unified L2 cache for the e6500 cluster +. Two 512 Kbyte shared L3 CoreNet platform caches (CPC) +. Sixteen 10-GHz SerDes lanes serving: +. Two Serial RapidIO interfaces. + - Each supports up to 4 lanes and a total of up to 8 lanes +. Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-less + antenna connection +. Two 10-Gbit Ethernet controllers (10GEC) +. Six 1G/2.5-Gbit Ethernet controllers for network communications +. PCI Express controller +. Debug (Aurora) +. Two OCeaN DMAs +. Various system peripherals +. 182 32-bit timers + +B4860QDS Overview +------------------ +- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 4 GB + of memory in two ranks of 2 GB. +- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB + of memory. Single rank. +- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point 16x16 switch + VSC3316 +- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point 8x8 switch VSC3308 +- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode. + B4860 UART port is available over USB-to-UART translator USB2SER or over RS232 flat cable. +- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper connectors + for Stand-alone mode and to the 1000Base-X over AMC MicroTCA connector ports 0 and 2 for + AMC mode. +- The B4860 configuration may be loaded from nine bits coded reset configuration reset source. The + RCW source is set by appropriate DIP-switches: +- 16-bit NOR Flash / PROMJet +- QIXIS 8-bit NOR Flash Emulator +- 8-bit NAND Flash +- 24-bit SPI Flash +- Long address I2C EEPROM +- Available debug interfaces are: + - On-board eCWTAP controller with ETH and USB I/F + - JTAG/COP 16-pin header for any external TAP controller + - External JTAG source over AMC to support B2B configuration + - 70-pin Aurora debug connector +- QIXIS (FPGA) logic: + - 2 KB internal memory space including +- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK, DDRCLK1,2 and + RTCCLK. +- Two 8T49N222A SerDes ref clock devices support two SerDes port clock frequency - total four + refclk, including CPRI clock scheme. + +B4420 Personality +-------------------- + +B4420 Personality +-------------------- +B4420 is a reduced personality of B4860 with less core/clusters(both SC3900 and e6500), less DDR +controllers, less serdes lanes, less SGMII interfaces and reduced target frequencies. + +Key differences between B4860 and B4420 +---------------------------------------- + +B4420 has: +1. Less e6500 cores: 1 cluster with 2 e6500 cores +2. Less SC3900 cores/clusters: 1 cluster with 2 SC3900 cores per cluster. +3. Single DDRC +4. 2X 4 lane serdes +5. 3 SGMII interfaces +6. no sRIO +7. no 10G + +B4860QDS Default Settings +------------------------- + +Switch Settings +---------------- + +SW1 OFF [0] OFF [1] OFF [1] OFF [0] OFF [1] OFF [0] OFF [1] OFF [1] +SW2 ON ON ON ON ON ON OFF OFF +SW3 OFF OFF OFF ON OFF OFF ON OFF +SW5 OFF OFF OFF OFF OFF OFF ON ON + +Note: PCIe slots modes: All the PCIe devices work as Root Complex. +Note: Boot location: NOR flash. + +SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple +66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz + +a) NAND boot + SW1 [1.1] = 0 + SW2 [1.1] = 1 + SW3 [1:4] = 0001 +b) NOR boot + SW1 [1.1] = 1 + SW2 [1.1] = 0 + SW3 [1:4] = 1000. + +B4420QDS Default Settings +------------------------- + +Switch Settings +---------------- +SW1 OFF[0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] +SW2 ON OFF ON OFF ON ON OFF OFF +SW3 OFF OFF OFF ON OFF OFF ON OFF +SW5 OFF OFF OFF OFF OFF OFF ON ON + +Note: PCIe slots modes: All the PCIe devices work as Root Complex. +Note: Boot location: NOR flash. + +SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple +66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz + +a) NAND boot + SW1 [1.1] = 0 + SW2 [1.1] = 1 + SW3 [1:4] = 0001 +b) NOR boot + SW1 [1.1] = 1 + SW2 [1.1] = 0 + SW3 [1:4] = 1000. + +Memory map on B4860QDS +---------------------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0xF_FFDF_1000 0xF_FFFF_FFFF Free 2 MB +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4 KB +0xF_FF81_0000 0xF_FFDE_FFFF Free 5 MB +0xF_FF80_0000 0xF_FF80_FFFF IFC NAND Flash 64 KB +0xF_FF00_0000 0xF_FF7F_FFFF Free 8 MB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16 MB +0xF_F801_0000 0xF_FDFF_FFFF Free 95 MB +0xF_F800_0000 0xF_F800_FFFF PCIe I/O Space 64 KB +0xF_F600_0000 0xF_F7FF_FFFF QMAN s/w portal 32 MB +0xF_F400_0000 0xF_F5FF_FFFF BMAN s/w portal 32 MB +0xF_F000_0000 0xF_F3FF_FFFF Free 64 MB +0xF_E800_0000 0xF_EFFF_FFFF IFC NOR Flash 128 MB +0xF_E000_0000 0xF_E7FF_FFFF Promjet 128 MB +0xF_A0C0_0000 0xF_DFFF_FFFF Free 1012 MB +0xF_A000_0000 0xF_A0BF_FFFF MAPLE0/1/2 12 MB +0xF_0040_0000 0xF_9FFF_FFFF Free 12 GB +0xF_0000_0000 0xF_003F_FFFF DCSR 4 MB +0xC_4000_0000 0xE_FFFF_FFFF Free 11 GB +0xC_3000_0000 0xC_3FFF_FFFF sRIO-2 I/O 256 MB +0xC_2000_0000 0xC_2FFF_FFFF sRIO-1 I/O 256 MB +0xC_0000_0000 0xC_1FFF_FFFF PCIe Mem Space 512 MB +0x1_0000_0000 0xB_FFFF_FFFF Free 44 GB +0x0_8000_0000 0x0_FFFF_FFFF DDRC1 2 GB +0x0_0000_0000 0x0_7FFF_FFFF DDRC2 2 GB + +Memory map on B4420QDS +---------------------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0xF_FFDF_1000 0xF_FFFF_FFFF Free 2 MB +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4 KB +0xF_FF81_0000 0xF_FFDE_FFFF Free 5 MB +0xF_FF80_0000 0xF_FF80_FFFF IFC NAND Flash 64 KB +0xF_FF00_0000 0xF_FF7F_FFFF Free 8 MB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16 MB +0xF_F801_0000 0xF_FDFF_FFFF Free 95 MB +0xF_F800_0000 0xF_F800_FFFF PCIe I/O Space 64 KB +0xF_F600_0000 0xF_F7FF_FFFF QMAN s/w portal 32 MB +0xF_F400_0000 0xF_F5FF_FFFF BMAN s/w portal 32 MB +0xF_F000_0000 0xF_F3FF_FFFF Free 64 MB +0xF_E800_0000 0xF_EFFF_FFFF IFC NOR Flash 128 MB +0xF_E000_0000 0xF_E7FF_FFFF Promjet 128 MB +0xF_A0C0_0000 0xF_DFFF_FFFF Free 1012 MB +0xF_A000_0000 0xF_A0BF_FFFF MAPLE0/1/2 12 MB +0xF_0040_0000 0xF_9FFF_FFFF Free 12 GB +0xF_0000_0000 0xF_003F_FFFF DCSR 4 MB +0xC_4000_0000 0xE_FFFF_FFFF Free 11 GB +0xC_3000_0000 0xC_3FFF_FFFF sRIO-2 I/O 256 MB +0xC_2000_0000 0xC_2FFF_FFFF sRIO-1 I/O 256 MB +0xC_0000_0000 0xC_1FFF_FFFF PCIe Mem Space 512 MB +0x1_0000_0000 0xB_FFFF_FFFF Free 44 GB +0x0_0000_0000 0x0_FFFF_FFFF DDRC1 4 GB + + +NOR Flash memory Map on B4860 and B4420QDS +------------------------------------------ + Start End Definition Size +0xEFF80000 0xEFFFFFFF u-boot (current bank) 512KB +0xEFF60000 0xEFF7FFFF u-boot env (current bank) 128KB +0xEFF40000 0xEFF5FFFF FMAN Ucode (current bank) 128KB +0xEF300000 0xEFF3FFFF rootfs (alternate bank) 12MB + 256KB +0xEE800000 0xEE8FFFFF device tree (alternate bank) 1MB +0xEE020000 0xEE6FFFFF Linux.uImage (alternate bank) 6MB+896KB +0xEE000000 0xEE01FFFF RCW (alternate bank) 128KB +0xEDF80000 0xEDFFFFFF u-boot (alternate bank) 512KB +0xEDF60000 0xEDF7FFFF u-boot env (alternate bank) 128KB +0xEDF40000 0xEDF5FFFF FMAN ucode (alternate bank) 128KB +0xED300000 0xEDF3FFFF rootfs (current bank) 12MB+256MB +0xEC800000 0xEC8FFFFF device tree (current bank) 1MB +0xEC020000 0xEC6FFFFF Linux.uImage (current bank) 6MB+896KB +0xEC000000 0xEC01FFFF RCW (current bank) 128KB + +Various Software configurations/environment variables/commands +-------------------------------------------------------------- +The below commands apply to both B4860QDS and B4420QDS. + +1. U-boot environment variable hwconfig + The default hwconfig is: + hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1: + dr_mode=host,phy_type=ulpi + Note: For USB gadget set "dr_mode=peripheral" + +2. FMAN Ucode versions + fsl_fman_ucode_B4860_106_3_6.bin + +3. Switching to alternate bank + Commands for switching to alternate bank. + + 1. To change from vbank0 to vbank2 + => qixis_reset altbank (it will boot using vbank2) + + 2.To change from vbank2 to vbank0 + => qixis reset (it will boot using vbank0) + +4. To change personality of board + For changing personality from B4860 to B4420 + 1)Boot from vbank0 + 2)Flash vbank2 with b4420 rcw and u-boot + 3)Give following commands to uboot prompt + => mw.b ffdf0040 0x30; + => mw.b ffdf0010 0x00; + => mw.b ffdf0062 0x02; + => mw.b ffdf0050 0x02; + => mw.b ffdf0010 0x30; + => reset + + Note: Power off cycle will lead to default switch settings. + Note: 0xffdf0000 is the address of the QIXIS FPGA. + +5. Switching between NOR and NAND boot(RCW src changed from NOR <-> NAND) + + To change from NOR to NAND boot give following command on uboot prompt + => mw.b ffdf0040 0x30 + => mw.b ffdf0010 0x00 + => mw.b 0xffdf0050 0x08 + => mw.b 0xffdf0060 0x82 + => mw.b ffdf0061 0x00 + => mw.b ffdf0010 0x30 + => reset + + To change from NAND to NOR boot give following command on uboot prompt: + => mw.b ffdf0040 0x30 + => mw.b ffdf0010 0x00 + => mw.b 0xffdf0050 0x00(for vbank0) or (mw.b 0xffdf0050 0x02 for vbank2) + => mw.b 0xffdf0060 0x12 + => mw.b ffdf0061 0x01 + => mw.b ffdf0010 0x30 + => reset + + Note: Power off cycle will lead to default switch settings. + Note: 0xffdf0000 is the address of the QIXIS FPGA. + +6. Ethernet interfaces for B4860QDS + Serdes protocosl tested: + 0x2a, 0x8d (serdes1, serdes2) [DEFAULT] + 0x2a, 0xb2 (serdes1, serdes2) + + When using [DEFAULT] RCW, which including 2 * 1G SGMII on board and 2 * 1G + SGMII on SGMII riser card. + Under U-boot these network interfaces are recognized as: + FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 and FM1@DTSEC6. + + On Linux the interfaces are renamed as: + . eth2 -> fm1-gb2 + . eth3 -> fm1-gb3 + . eth4 -> fm1-gb4 + . eth5 -> fm1-gb5 + +7. RCW and Ethernet interfaces for B4420QDS + Serdes protocosl tested: + 0x18, 0x9e (serdes1, serdes2) + + Under U-boot these network interfaces are recognized as: + FM1@DTSEC3, FM1@DTSEC4 and e1000#0. + + On Linux the interfaces are renamed as: + . eth2 -> fm1-gb2 + . eth3 -> fm1-gb3 diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h new file mode 100644 index 0000000..b09119a --- /dev/null +++ b/include/configs/B4860QDS.h @@ -0,0 +1,820 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * B4860 QDS board configuration file + */ +#define CONFIG_B4860QDS +#define CONFIG_PHYS_64BIT + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E6500 +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ +#define CONFIG_MP /* support multiple processors */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#ifndef CONFIG_PPC_B4420 +#define CONFIG_SYS_SRIO +#define CONFIG_SRIO1 /* SRIO port 1 */ +#define CONFIG_SRIO2 /* SRIO port 2 */ +#endif + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR 0x77 + +/* VSC Crossbar switches */ +#define CONFIG_VSC_CROSSBAR +#define I2C_CH_DEFAULT 0x8 +#define I2C_CH_VSC3316 0xc +#define I2C_CH_VSC3308 0xd + +#define VSC3316_TX_ADDRESS 0x70 +#define VSC3316_RX_ADDRESS 0x71 +#define VSC3308_TX_ADDRESS 0x02 +#define VSC3308_RX_ADDRESS 0x03 + +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#ifndef CONFIG_SYS_NO_FLASH +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1097) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif +#else /* CONFIG_SYS_NO_FLASH */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ +#endif + +#if 0 +#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ +#endif +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull +#endif + +/* EEPROM */ +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_SYS_DDR_RAW_TIMING +#define CONFIG_FSL_DDR3 +#define CONFIG_FSL_DDR_INTERACTIVE + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x53 + +#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 +#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) +#else +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#endif + +#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR1_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) | \ + FTIM0_NOR_TEADC(0x01) | \ + FTIM0_NOR_TEAHC(0x20)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x01) | \ + FTIM2_NOR_TCH(0x0E) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} + +#define CONFIG_FSL_QIXIS /* use common QIXIS code */ +#define CONFIG_FSL_QIXIS_V2 +#define QIXIS_BASE 0xffdf0000 +#ifdef CONFIG_PHYS_64BIT +#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) +#else +#define QIXIS_BASE_PHYS QIXIS_BASE +#endif +#define QIXIS_LBMAP_SWITCH 0x01 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SHIFT 0 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x02 +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 + +#define CONFIG_SYS_CSPR3_EXT (0xf) +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK3 IFC_AMASK(4 * 1024) +#define CONFIG_SYS_CSOR3 0x0 +/* QIXIS Timing parameters for IFC CS3 */ +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS3_FTIM3 0x0 + +/* NAND Flash on IFC */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) +#else +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#endif + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ + | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ + | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#else +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe0ec000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS +#endif +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x118000 +#define CONFIG_SYS_I2C2_OFFSET 0x119000 + +/* + * RTC configuration + */ +#define RTC +#define CONFIG_RTC_DS3231 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/* + * RapidIO + */ +#ifdef CONFIG_SYS_SRIO +#ifdef CONFIG_SRIO1 +#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull +#else +#define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 +#endif +#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ +#endif + +#ifdef CONFIG_SRIO2 +#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull +#else +#define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 +#endif +#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ +#endif +#endif + +/* + * for slave u-boot IMAGE instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +/* + * for slave UCODE and ENV instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ + +/* slave core release by master*/ +#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 +#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ + +/* + * SRIO_PCIE_BOOT - SLAVE + */ +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) +#endif + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SST +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#else +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 +#endif +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#else +#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 +#endif +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 25 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#else +#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE +#endif +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 25 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#else +#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE +#endif +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 545KB (1089 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_TERANETICS +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x10 +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x11 +#endif + +#ifdef CONFIG_PCI +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10 +#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11 +#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4 + +#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c +#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d +#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e +#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* +* USB +*/ +#define CONFIG_HAS_FSL_DR_USB + +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#endif +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ + +#define CONFIG_BAUDRATE 115200 + +#define __USB_PHY_TYPE ulpi + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=null," \ + "bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=b4860qds/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=b4860qds/b4860qds.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" + +/* For emulation this causes u-boot to jump to the start of the proof point + app code automatically */ +#define CONFIG_PROOF_POINTS \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "cpu 1 release 0x29000000 - - -;" \ + "cpu 2 release 0x29000000 - - -;" \ + "cpu 3 release 0x29000000 - - -;" \ + "cpu 4 release 0x29000000 - - -;" \ + "cpu 5 release 0x29000000 - - -;" \ + "cpu 6 release 0x29000000 - - -;" \ + "cpu 7 release 0x29000000 - - -;" \ + "go 0x29000000" + +#define CONFIG_HVBOOT \ + "setenv bootargs config-addr=0x60000000; " \ + "bootm 0x01000000 - 0x00f00000" + +#define CONFIG_ALU \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "cpu 1 release 0x01000000 - - -;" \ + "cpu 2 release 0x01000000 - - -;" \ + "cpu 3 release 0x01000000 - - -;" \ + "cpu 4 release 0x01000000 - - -;" \ + "cpu 5 release 0x01000000 - - -;" \ + "cpu 6 release 0x01000000 - - -;" \ + "cpu 7 release 0x01000000 - - -;" \ + "go 0x01000000" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#ifdef CONFIG_SECURE_BOOT +#include <asm/fsl_secure_boot.h> +#endif + +#endif /* __CONFIG_H */