[PATCH u-boot] doc: board: qemu-ppce500: Update supported and unsupported
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org --- doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/doc/board/emulation/qemu-ppce500.rst b/doc/board/emulation/qemu-ppce500.rst index 5de0aaf55ded..10427cc56302 100644 --- a/doc/board/emulation/qemu-ppce500.rst +++ b/doc/board/emulation/qemu-ppce500.rst @@ -7,7 +7,7 @@ QEMU PPC E500 QEMU for PPC supports a special 'ppce500' machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it.
-The QEMU ppce500 machine models a generic PowerPC E500 virtual machine with +The QEMU ppce500 machine models a generic PowerPC e500 virtual machine with support for the VirtIO standard networking device connected to the built-in PCI host controller. Some common devices in the CCSBAR space are modeled, including MPIC, 16550A UART devices, GPIO, I2C and PCI host controller with @@ -39,6 +39,7 @@ embedded DTB created by QEMU reflects the new setting. Both qemu-system-ppc and qemu-system-ppc64 provide emulation for the following 32-bit PowerPC CPUs:
+* e500v1 * e500v2 * e500mc
@@ -61,8 +62,9 @@ When U-Boot boots, you will notice the following:: This is because we only specified a core name to QEMU and it does not have a meaningful SVR value which represents an actual SoC that integrates such core. You can specify a real world SoC device that QEMU has built-in support but all -these SoCs are e500v2 based MPC85xx series, hence you cannot test anything -built for P4080 (e500mc), P5020 (e5500) and T2080 (e6500). +these SoCs are e500v1/e500v2 based MPC85xx series, hence you cannot test anything +built for P10xx/P2010/P2020 (e500v2), P2O4x/P304x/P40xx (e500mc), P50xx/T10xx (e5500) +and T208x/T4080/T4160/T4240 (e6500).
By default a VirtIO standard PCI networking device is connected as an ethernet interface at PCI address 0.1.0, but we can switch that to an e1000 NIC by::
On Wed, Dec 21, 2022 at 4:06 AM Pali Rohár pali@kernel.org wrote:
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org
doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/doc/board/emulation/qemu-ppce500.rst b/doc/board/emulation/qemu-ppce500.rst index 5de0aaf55ded..10427cc56302 100644 --- a/doc/board/emulation/qemu-ppce500.rst +++ b/doc/board/emulation/qemu-ppce500.rst @@ -7,7 +7,7 @@ QEMU PPC E500 QEMU for PPC supports a special 'ppce500' machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it.
-The QEMU ppce500 machine models a generic PowerPC E500 virtual machine with +The QEMU ppce500 machine models a generic PowerPC e500 virtual machine with support for the VirtIO standard networking device connected to the built-in PCI host controller. Some common devices in the CCSBAR space are modeled, including MPIC, 16550A UART devices, GPIO, I2C and PCI host controller with @@ -39,6 +39,7 @@ embedded DTB created by QEMU reflects the new setting. Both qemu-system-ppc and qemu-system-ppc64 provide emulation for the following 32-bit PowerPC CPUs:
+* e500v1
- e500v2
- e500mc
@@ -61,8 +62,9 @@ When U-Boot boots, you will notice the following:: This is because we only specified a core name to QEMU and it does not have a meaningful SVR value which represents an actual SoC that integrates such core. You can specify a real world SoC device that QEMU has built-in support but all -these SoCs are e500v2 based MPC85xx series, hence you cannot test anything -built for P4080 (e500mc), P5020 (e5500) and T2080 (e6500). +these SoCs are e500v1/e500v2 based MPC85xx series, hence you cannot test anything +built for P10xx/P2010/P2020 (e500v2), P2O4x/P304x/P40xx (e500mc), P50xx/T10xx (e5500)
typo: P2O4x
+and T208x/T4080/T4160/T4240 (e6500).
By default a VirtIO standard PCI networking device is connected as an ethernet interface at PCI address 0.1.0, but we can switch that to an e1000 NIC by:: --
Regards, Bin
On Wednesday 21 December 2022 09:15:41 Bin Meng wrote:
On Wed, Dec 21, 2022 at 4:06 AM Pali Rohár pali@kernel.org wrote:
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org
doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/doc/board/emulation/qemu-ppce500.rst b/doc/board/emulation/qemu-ppce500.rst index 5de0aaf55ded..10427cc56302 100644 --- a/doc/board/emulation/qemu-ppce500.rst +++ b/doc/board/emulation/qemu-ppce500.rst @@ -7,7 +7,7 @@ QEMU PPC E500 QEMU for PPC supports a special 'ppce500' machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it.
-The QEMU ppce500 machine models a generic PowerPC E500 virtual machine with +The QEMU ppce500 machine models a generic PowerPC e500 virtual machine with support for the VirtIO standard networking device connected to the built-in PCI host controller. Some common devices in the CCSBAR space are modeled, including MPIC, 16550A UART devices, GPIO, I2C and PCI host controller with @@ -39,6 +39,7 @@ embedded DTB created by QEMU reflects the new setting. Both qemu-system-ppc and qemu-system-ppc64 provide emulation for the following 32-bit PowerPC CPUs:
+* e500v1
- e500v2
- e500mc
@@ -61,8 +62,9 @@ When U-Boot boots, you will notice the following:: This is because we only specified a core name to QEMU and it does not have a meaningful SVR value which represents an actual SoC that integrates such core. You can specify a real world SoC device that QEMU has built-in support but all -these SoCs are e500v2 based MPC85xx series, hence you cannot test anything -built for P4080 (e500mc), P5020 (e5500) and T2080 (e6500). +these SoCs are e500v1/e500v2 based MPC85xx series, hence you cannot test anything +built for P10xx/P2010/P2020 (e500v2), P2O4x/P304x/P40xx (e500mc), P50xx/T10xx (e5500)
typo: P2O4x
Where is a typo? I wrote P204x (which should mean both P2040 and P2041).
+and T208x/T4080/T4160/T4240 (e6500).
By default a VirtIO standard PCI networking device is connected as an ethernet interface at PCI address 0.1.0, but we can switch that to an e1000 NIC by:: --
Regards, Bin
On Wed, Dec 21, 2022 at 3:49 PM Pali Rohár pali@kernel.org wrote:
On Wednesday 21 December 2022 09:15:41 Bin Meng wrote:
On Wed, Dec 21, 2022 at 4:06 AM Pali Rohár pali@kernel.org wrote:
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org
doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/doc/board/emulation/qemu-ppce500.rst b/doc/board/emulation/qemu-ppce500.rst index 5de0aaf55ded..10427cc56302 100644 --- a/doc/board/emulation/qemu-ppce500.rst +++ b/doc/board/emulation/qemu-ppce500.rst @@ -7,7 +7,7 @@ QEMU PPC E500 QEMU for PPC supports a special 'ppce500' machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it.
-The QEMU ppce500 machine models a generic PowerPC E500 virtual machine with +The QEMU ppce500 machine models a generic PowerPC e500 virtual machine with support for the VirtIO standard networking device connected to the built-in PCI host controller. Some common devices in the CCSBAR space are modeled, including MPIC, 16550A UART devices, GPIO, I2C and PCI host controller with @@ -39,6 +39,7 @@ embedded DTB created by QEMU reflects the new setting. Both qemu-system-ppc and qemu-system-ppc64 provide emulation for the following 32-bit PowerPC CPUs:
+* e500v1
- e500v2
- e500mc
@@ -61,8 +62,9 @@ When U-Boot boots, you will notice the following:: This is because we only specified a core name to QEMU and it does not have a meaningful SVR value which represents an actual SoC that integrates such core. You can specify a real world SoC device that QEMU has built-in support but all -these SoCs are e500v2 based MPC85xx series, hence you cannot test anything -built for P4080 (e500mc), P5020 (e5500) and T2080 (e6500). +these SoCs are e500v1/e500v2 based MPC85xx series, hence you cannot test anything +built for P10xx/P2010/P2020 (e500v2), P2O4x/P304x/P40xx (e500mc), P50xx/T10xx (e5500)
typo: P2O4x
Where is a typo? I wrote P204x (which should mean both P2040 and P2041).
Is that 0 or O? It looks like an O.
+and T208x/T4080/T4160/T4240 (e6500).
By default a VirtIO standard PCI networking device is connected as an ethernet interface at PCI address 0.1.0, but we can switch that to an e1000 NIC by:: --
Regards, Bin
On Wednesday 21 December 2022 17:01:37 Bin Meng wrote:
On Wed, Dec 21, 2022 at 3:49 PM Pali Rohár pali@kernel.org wrote:
On Wednesday 21 December 2022 09:15:41 Bin Meng wrote:
On Wed, Dec 21, 2022 at 4:06 AM Pali Rohár pali@kernel.org wrote:
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org
doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/doc/board/emulation/qemu-ppce500.rst b/doc/board/emulation/qemu-ppce500.rst index 5de0aaf55ded..10427cc56302 100644 --- a/doc/board/emulation/qemu-ppce500.rst +++ b/doc/board/emulation/qemu-ppce500.rst @@ -7,7 +7,7 @@ QEMU PPC E500 QEMU for PPC supports a special 'ppce500' machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it.
-The QEMU ppce500 machine models a generic PowerPC E500 virtual machine with +The QEMU ppce500 machine models a generic PowerPC e500 virtual machine with support for the VirtIO standard networking device connected to the built-in PCI host controller. Some common devices in the CCSBAR space are modeled, including MPIC, 16550A UART devices, GPIO, I2C and PCI host controller with @@ -39,6 +39,7 @@ embedded DTB created by QEMU reflects the new setting. Both qemu-system-ppc and qemu-system-ppc64 provide emulation for the following 32-bit PowerPC CPUs:
+* e500v1
- e500v2
- e500mc
@@ -61,8 +62,9 @@ When U-Boot boots, you will notice the following:: This is because we only specified a core name to QEMU and it does not have a meaningful SVR value which represents an actual SoC that integrates such core. You can specify a real world SoC device that QEMU has built-in support but all -these SoCs are e500v2 based MPC85xx series, hence you cannot test anything -built for P4080 (e500mc), P5020 (e5500) and T2080 (e6500). +these SoCs are e500v1/e500v2 based MPC85xx series, hence you cannot test anything +built for P10xx/P2010/P2020 (e500v2), P2O4x/P304x/P40xx (e500mc), P50xx/T10xx (e5500)
typo: P2O4x
Where is a typo? I wrote P204x (which should mean both P2040 and P2041).
Is that 0 or O? It looks like an O.
Ou. Now I see what you mean. I had to look at it 3 times to see that difference is between number zero and capital letter o. I have no idea why I typed here letter instead of number... maybe because these keys are near each other.
Of course, it is zero not letter o. Sorry for this.
Would you fix it locally, or should I send a new patch version?
+and T208x/T4080/T4160/T4240 (e6500).
By default a VirtIO standard PCI networking device is connected as an ethernet interface at PCI address 0.1.0, but we can switch that to an e1000 NIC by:: --
Regards, Bin
On Thu, Dec 22, 2022 at 6:43 AM Pali Rohár pali@kernel.org wrote:
On Wednesday 21 December 2022 17:01:37 Bin Meng wrote:
On Wed, Dec 21, 2022 at 3:49 PM Pali Rohár pali@kernel.org wrote:
On Wednesday 21 December 2022 09:15:41 Bin Meng wrote:
On Wed, Dec 21, 2022 at 4:06 AM Pali Rohár pali@kernel.org wrote:
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org
doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/doc/board/emulation/qemu-ppce500.rst b/doc/board/emulation/qemu-ppce500.rst index 5de0aaf55ded..10427cc56302 100644 --- a/doc/board/emulation/qemu-ppce500.rst +++ b/doc/board/emulation/qemu-ppce500.rst @@ -7,7 +7,7 @@ QEMU PPC E500 QEMU for PPC supports a special 'ppce500' machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it.
-The QEMU ppce500 machine models a generic PowerPC E500 virtual machine with +The QEMU ppce500 machine models a generic PowerPC e500 virtual machine with support for the VirtIO standard networking device connected to the built-in PCI host controller. Some common devices in the CCSBAR space are modeled, including MPIC, 16550A UART devices, GPIO, I2C and PCI host controller with @@ -39,6 +39,7 @@ embedded DTB created by QEMU reflects the new setting. Both qemu-system-ppc and qemu-system-ppc64 provide emulation for the following 32-bit PowerPC CPUs:
+* e500v1
- e500v2
- e500mc
@@ -61,8 +62,9 @@ When U-Boot boots, you will notice the following:: This is because we only specified a core name to QEMU and it does not have a meaningful SVR value which represents an actual SoC that integrates such core. You can specify a real world SoC device that QEMU has built-in support but all -these SoCs are e500v2 based MPC85xx series, hence you cannot test anything -built for P4080 (e500mc), P5020 (e5500) and T2080 (e6500). +these SoCs are e500v1/e500v2 based MPC85xx series, hence you cannot test anything +built for P10xx/P2010/P2020 (e500v2), P2O4x/P304x/P40xx (e500mc), P50xx/T10xx (e5500)
typo: P2O4x
Where is a typo? I wrote P204x (which should mean both P2040 and P2041).
Is that 0 or O? It looks like an O.
Ou. Now I see what you mean. I had to look at it 3 times to see that difference is between number zero and capital letter o. I have no idea why I typed here letter instead of number... maybe because these keys are near each other.
Of course, it is zero not letter o. Sorry for this.
Would you fix it locally, or should I send a new patch version?
Please send a new patch as I assume I am not the one to pick up this patch.
Regards, Bin
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org
--- Changes in v2: * sed 's/P2O4x/P204x/' --- doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/doc/board/emulation/qemu-ppce500.rst b/doc/board/emulation/qemu-ppce500.rst index 5de0aaf55ded..82b50a01de7e 100644 --- a/doc/board/emulation/qemu-ppce500.rst +++ b/doc/board/emulation/qemu-ppce500.rst @@ -7,7 +7,7 @@ QEMU PPC E500 QEMU for PPC supports a special 'ppce500' machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it.
-The QEMU ppce500 machine models a generic PowerPC E500 virtual machine with +The QEMU ppce500 machine models a generic PowerPC e500 virtual machine with support for the VirtIO standard networking device connected to the built-in PCI host controller. Some common devices in the CCSBAR space are modeled, including MPIC, 16550A UART devices, GPIO, I2C and PCI host controller with @@ -39,6 +39,7 @@ embedded DTB created by QEMU reflects the new setting. Both qemu-system-ppc and qemu-system-ppc64 provide emulation for the following 32-bit PowerPC CPUs:
+* e500v1 * e500v2 * e500mc
@@ -61,8 +62,9 @@ When U-Boot boots, you will notice the following:: This is because we only specified a core name to QEMU and it does not have a meaningful SVR value which represents an actual SoC that integrates such core. You can specify a real world SoC device that QEMU has built-in support but all -these SoCs are e500v2 based MPC85xx series, hence you cannot test anything -built for P4080 (e500mc), P5020 (e5500) and T2080 (e6500). +these SoCs are e500v1/e500v2 based MPC85xx series, hence you cannot test anything +built for P10xx/P2010/P2020 (e500v2), P204x/P304x/P40xx (e500mc), P50xx/T10xx (e5500) +and T208x/T4080/T4160/T4240 (e6500).
By default a VirtIO standard PCI networking device is connected as an ethernet interface at PCI address 0.1.0, but we can switch that to an e1000 NIC by::
On Sat, Dec 24, 2022 at 3:15 AM Pali Rohár pali@kernel.org wrote:
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár pali@kernel.org
Changes in v2:
- sed 's/P2O4x/P204x/'
doc/board/emulation/qemu-ppce500.rst | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
Reviewed-by: Bin Meng bmeng.cn@gmail.com
participants (2)
-
Bin Meng -
Pali Rohár