[U-Boot] [PATCH v1 0/4] DM: Convert i.MX28 gpio, pinmux and eth drivers to DM/DTS
This patch series converts some i.MX28 drivers to use DM/DTS.
Converted drivers: - mxs_gpio.c - gpio driver - pinctrl-mxs.c - pinmux driver - Adjust fec_eth.c to support also i.MX28 SoC.
This patch series shall help with coordinated i.MX28 DM/DTS conversion and avoidance of effort duplication.
After applying this series it is possible to use ETH on i.MX28 board with following DTS description:
&mac0 { phy-mode = "rmii"; pinctrl-names = "default"; pinctrl-0 = <&mac0_pins_a>; phy-supply = <®_fec_3v3>; phy-reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; phy-reset-duration = <1>; phy-reset-post-delay = <1>; status = "okay";
fixed-link { speed = <100>; full-duplex; }; };
Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/543773376
Applied on top of u-boot/master branch SHA1: dbbb1c43f26cb28b64df80b72fffbaf2801e8a30
Lukasz Majewski (4): DTS: imx28: Copy imx28 device tree related files from Linux kernel (v5.1.2) imx: net: Enable support for i.MX28 DM_ETH in the fec_mxc.c driver DM: mxs: gpio: Add support for DM/DTS in the mxs_gpio.c driver (DM_GPIO) imx: pinctrl: Add support for i.MX28 mxs pinctrl driver
arch/arm/dts/imx28-pinfunc.h | 506 +++++++++++++ arch/arm/dts/imx28.dtsi | 1330 ++++++++++++++++++++++++++++++++++ arch/arm/dts/mxs-pinfunc.h | 31 + arch/arm/include/asm/arch-mxs/gpio.h | 28 + drivers/gpio/mxs_gpio.c | 149 ++++ drivers/net/Kconfig | 2 +- drivers/net/fec_mxc.c | 1 + drivers/pinctrl/nxp/Kconfig | 10 + drivers/pinctrl/nxp/Makefile | 1 + drivers/pinctrl/nxp/pinctrl-mxs.c | 164 +++++ 10 files changed, 2221 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx28-pinfunc.h create mode 100644 arch/arm/dts/imx28.dtsi create mode 100644 arch/arm/dts/mxs-pinfunc.h create mode 100644 drivers/pinctrl/nxp/pinctrl-mxs.c
This commit copies from the Linux kernel (tag v5.1.2) i.MX28 related device tree files.
Signed-off-by: Lukasz Majewski lukma@denx.de ---
arch/arm/dts/imx28-pinfunc.h | 506 ++++++++++++++++ arch/arm/dts/imx28.dtsi | 1330 ++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/mxs-pinfunc.h | 31 + 3 files changed, 1867 insertions(+) create mode 100644 arch/arm/dts/imx28-pinfunc.h create mode 100644 arch/arm/dts/imx28.dtsi create mode 100644 arch/arm/dts/mxs-pinfunc.h
diff --git a/arch/arm/dts/imx28-pinfunc.h b/arch/arm/dts/imx28-pinfunc.h new file mode 100644 index 0000000000..e11f69ba0f --- /dev/null +++ b/arch/arm/dts/imx28-pinfunc.h @@ -0,0 +1,506 @@ +/* + * Header providing constants for i.MX28 pinctrl bindings. + * + * Copyright (C) 2013 Lothar Waßmann LW@KARO-electronics.de + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DT_BINDINGS_MX28_PINCTRL_H__ +#define __DT_BINDINGS_MX28_PINCTRL_H__ + +#include "mxs-pinfunc.h" + +#define MX28_PAD_GPMI_D00__GPMI_D0 0x0000 +#define MX28_PAD_GPMI_D01__GPMI_D1 0x0010 +#define MX28_PAD_GPMI_D02__GPMI_D2 0x0020 +#define MX28_PAD_GPMI_D03__GPMI_D3 0x0030 +#define MX28_PAD_GPMI_D04__GPMI_D4 0x0040 +#define MX28_PAD_GPMI_D05__GPMI_D5 0x0050 +#define MX28_PAD_GPMI_D06__GPMI_D6 0x0060 +#define MX28_PAD_GPMI_D07__GPMI_D7 0x0070 +#define MX28_PAD_GPMI_CE0N__GPMI_CE0N 0x0100 +#define MX28_PAD_GPMI_CE1N__GPMI_CE1N 0x0110 +#define MX28_PAD_GPMI_CE2N__GPMI_CE2N 0x0120 +#define MX28_PAD_GPMI_CE3N__GPMI_CE3N 0x0130 +#define MX28_PAD_GPMI_RDY0__GPMI_READY0 0x0140 +#define MX28_PAD_GPMI_RDY1__GPMI_READY1 0x0150 +#define MX28_PAD_GPMI_RDY2__GPMI_READY2 0x0160 +#define MX28_PAD_GPMI_RDY3__GPMI_READY3 0x0170 +#define MX28_PAD_GPMI_RDN__GPMI_RDN 0x0180 +#define MX28_PAD_GPMI_WRN__GPMI_WRN 0x0190 +#define MX28_PAD_GPMI_ALE__GPMI_ALE 0x01a0 +#define MX28_PAD_GPMI_CLE__GPMI_CLE 0x01b0 +#define MX28_PAD_GPMI_RESETN__GPMI_RESETN 0x01c0 +#define MX28_PAD_LCD_D00__LCD_D0 0x1000 +#define MX28_PAD_LCD_D01__LCD_D1 0x1010 +#define MX28_PAD_LCD_D02__LCD_D2 0x1020 +#define MX28_PAD_LCD_D03__LCD_D3 0x1030 +#define MX28_PAD_LCD_D04__LCD_D4 0x1040 +#define MX28_PAD_LCD_D05__LCD_D5 0x1050 +#define MX28_PAD_LCD_D06__LCD_D6 0x1060 +#define MX28_PAD_LCD_D07__LCD_D7 0x1070 +#define MX28_PAD_LCD_D08__LCD_D8 0x1080 +#define MX28_PAD_LCD_D09__LCD_D9 0x1090 +#define MX28_PAD_LCD_D10__LCD_D10 0x10a0 +#define MX28_PAD_LCD_D11__LCD_D11 0x10b0 +#define MX28_PAD_LCD_D12__LCD_D12 0x10c0 +#define MX28_PAD_LCD_D13__LCD_D13 0x10d0 +#define MX28_PAD_LCD_D14__LCD_D14 0x10e0 +#define MX28_PAD_LCD_D15__LCD_D15 0x10f0 +#define MX28_PAD_LCD_D16__LCD_D16 0x1100 +#define MX28_PAD_LCD_D17__LCD_D17 0x1110 +#define MX28_PAD_LCD_D18__LCD_D18 0x1120 +#define MX28_PAD_LCD_D19__LCD_D19 0x1130 +#define MX28_PAD_LCD_D20__LCD_D20 0x1140 +#define MX28_PAD_LCD_D21__LCD_D21 0x1150 +#define MX28_PAD_LCD_D22__LCD_D22 0x1160 +#define MX28_PAD_LCD_D23__LCD_D23 0x1170 +#define MX28_PAD_LCD_RD_E__LCD_RD_E 0x1180 +#define MX28_PAD_LCD_WR_RWN__LCD_WR_RWN 0x1190 +#define MX28_PAD_LCD_RS__LCD_RS 0x11a0 +#define MX28_PAD_LCD_CS__LCD_CS 0x11b0 +#define MX28_PAD_LCD_VSYNC__LCD_VSYNC 0x11c0 +#define MX28_PAD_LCD_HSYNC__LCD_HSYNC 0x11d0 +#define MX28_PAD_LCD_DOTCLK__LCD_DOTCLK 0x11e0 +#define MX28_PAD_LCD_ENABLE__LCD_ENABLE 0x11f0 +#define MX28_PAD_SSP0_DATA0__SSP0_D0 0x2000 +#define MX28_PAD_SSP0_DATA1__SSP0_D1 0x2010 +#define MX28_PAD_SSP0_DATA2__SSP0_D2 0x2020 +#define MX28_PAD_SSP0_DATA3__SSP0_D3 0x2030 +#define MX28_PAD_SSP0_DATA4__SSP0_D4 0x2040 +#define MX28_PAD_SSP0_DATA5__SSP0_D5 0x2050 +#define MX28_PAD_SSP0_DATA6__SSP0_D6 0x2060 +#define MX28_PAD_SSP0_DATA7__SSP0_D7 0x2070 +#define MX28_PAD_SSP0_CMD__SSP0_CMD 0x2080 +#define MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT 0x2090 +#define MX28_PAD_SSP0_SCK__SSP0_SCK 0x20a0 +#define MX28_PAD_SSP1_SCK__SSP1_SCK 0x20c0 +#define MX28_PAD_SSP1_CMD__SSP1_CMD 0x20d0 +#define MX28_PAD_SSP1_DATA0__SSP1_D0 0x20e0 +#define MX28_PAD_SSP1_DATA3__SSP1_D3 0x20f0 +#define MX28_PAD_SSP2_SCK__SSP2_SCK 0x2100 +#define MX28_PAD_SSP2_MOSI__SSP2_CMD 0x2110 +#define MX28_PAD_SSP2_MISO__SSP2_D0 0x2120 +#define MX28_PAD_SSP2_SS0__SSP2_D3 0x2130 +#define MX28_PAD_SSP2_SS1__SSP2_D4 0x2140 +#define MX28_PAD_SSP2_SS2__SSP2_D5 0x2150 +#define MX28_PAD_SSP3_SCK__SSP3_SCK 0x2180 +#define MX28_PAD_SSP3_MOSI__SSP3_CMD 0x2190 +#define MX28_PAD_SSP3_MISO__SSP3_D0 0x21a0 +#define MX28_PAD_SSP3_SS0__SSP3_D3 0x21b0 +#define MX28_PAD_AUART0_RX__AUART0_RX 0x3000 +#define MX28_PAD_AUART0_TX__AUART0_TX 0x3010 +#define MX28_PAD_AUART0_CTS__AUART0_CTS 0x3020 +#define MX28_PAD_AUART0_RTS__AUART0_RTS 0x3030 +#define MX28_PAD_AUART1_RX__AUART1_RX 0x3040 +#define MX28_PAD_AUART1_TX__AUART1_TX 0x3050 +#define MX28_PAD_AUART1_CTS__AUART1_CTS 0x3060 +#define MX28_PAD_AUART1_RTS__AUART1_RTS 0x3070 +#define MX28_PAD_AUART2_RX__AUART2_RX 0x3080 +#define MX28_PAD_AUART2_TX__AUART2_TX 0x3090 +#define MX28_PAD_AUART2_CTS__AUART2_CTS 0x30a0 +#define MX28_PAD_AUART2_RTS__AUART2_RTS 0x30b0 +#define MX28_PAD_AUART3_RX__AUART3_RX 0x30c0 +#define MX28_PAD_AUART3_TX__AUART3_TX 0x30d0 +#define MX28_PAD_AUART3_CTS__AUART3_CTS 0x30e0 +#define MX28_PAD_AUART3_RTS__AUART3_RTS 0x30f0 +#define MX28_PAD_PWM0__PWM_0 0x3100 +#define MX28_PAD_PWM1__PWM_1 0x3110 +#define MX28_PAD_PWM2__PWM_2 0x3120 +#define MX28_PAD_SAIF0_MCLK__SAIF0_MCLK 0x3140 +#define MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK 0x3150 +#define MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK 0x3160 +#define MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 0x3170 +#define MX28_PAD_I2C0_SCL__I2C0_SCL 0x3180 +#define MX28_PAD_I2C0_SDA__I2C0_SDA 0x3190 +#define MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 0x31a0 +#define MX28_PAD_SPDIF__SPDIF_TX 0x31b0 +#define MX28_PAD_PWM3__PWM_3 0x31c0 +#define MX28_PAD_PWM4__PWM_4 0x31d0 +#define MX28_PAD_LCD_RESET__LCD_RESET 0x31e0 +#define MX28_PAD_ENET0_MDC__ENET0_MDC 0x4000 +#define MX28_PAD_ENET0_MDIO__ENET0_MDIO 0x4010 +#define MX28_PAD_ENET0_RX_EN__ENET0_RX_EN 0x4020 +#define MX28_PAD_ENET0_RXD0__ENET0_RXD0 0x4030 +#define MX28_PAD_ENET0_RXD1__ENET0_RXD1 0x4040 +#define MX28_PAD_ENET0_TX_CLK__ENET0_TX_CLK 0x4050 +#define MX28_PAD_ENET0_TX_EN__ENET0_TX_EN 0x4060 +#define MX28_PAD_ENET0_TXD0__ENET0_TXD0 0x4070 +#define MX28_PAD_ENET0_TXD1__ENET0_TXD1 0x4080 +#define MX28_PAD_ENET0_RXD2__ENET0_RXD2 0x4090 +#define MX28_PAD_ENET0_RXD3__ENET0_RXD3 0x40a0 +#define MX28_PAD_ENET0_TXD2__ENET0_TXD2 0x40b0 +#define MX28_PAD_ENET0_TXD3__ENET0_TXD3 0x40c0 +#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_CLK 0x40d0 +#define MX28_PAD_ENET0_COL__ENET0_COL 0x40e0 +#define MX28_PAD_ENET0_CRS__ENET0_CRS 0x40f0 +#define MX28_PAD_ENET_CLK__CLKCTRL_ENET 0x4100 +#define MX28_PAD_JTAG_RTCK__JTAG_RTCK 0x4140 +#define MX28_PAD_EMI_D00__EMI_DATA0 0x5000 +#define MX28_PAD_EMI_D01__EMI_DATA1 0x5010 +#define MX28_PAD_EMI_D02__EMI_DATA2 0x5020 +#define MX28_PAD_EMI_D03__EMI_DATA3 0x5030 +#define MX28_PAD_EMI_D04__EMI_DATA4 0x5040 +#define MX28_PAD_EMI_D05__EMI_DATA5 0x5050 +#define MX28_PAD_EMI_D06__EMI_DATA6 0x5060 +#define MX28_PAD_EMI_D07__EMI_DATA7 0x5070 +#define MX28_PAD_EMI_D08__EMI_DATA8 0x5080 +#define MX28_PAD_EMI_D09__EMI_DATA9 0x5090 +#define MX28_PAD_EMI_D10__EMI_DATA10 0x50a0 +#define MX28_PAD_EMI_D11__EMI_DATA11 0x50b0 +#define MX28_PAD_EMI_D12__EMI_DATA12 0x50c0 +#define MX28_PAD_EMI_D13__EMI_DATA13 0x50d0 +#define MX28_PAD_EMI_D14__EMI_DATA14 0x50e0 +#define MX28_PAD_EMI_D15__EMI_DATA15 0x50f0 +#define MX28_PAD_EMI_ODT0__EMI_ODT0 0x5100 +#define MX28_PAD_EMI_DQM0__EMI_DQM0 0x5110 +#define MX28_PAD_EMI_ODT1__EMI_ODT1 0x5120 +#define MX28_PAD_EMI_DQM1__EMI_DQM1 0x5130 +#define MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK 0x5140 +#define MX28_PAD_EMI_CLK__EMI_CLK 0x5150 +#define MX28_PAD_EMI_DQS0__EMI_DQS0 0x5160 +#define MX28_PAD_EMI_DQS1__EMI_DQS1 0x5170 +#define MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN 0x51a0 +#define MX28_PAD_EMI_A00__EMI_ADDR0 0x6000 +#define MX28_PAD_EMI_A01__EMI_ADDR1 0x6010 +#define MX28_PAD_EMI_A02__EMI_ADDR2 0x6020 +#define MX28_PAD_EMI_A03__EMI_ADDR3 0x6030 +#define MX28_PAD_EMI_A04__EMI_ADDR4 0x6040 +#define MX28_PAD_EMI_A05__EMI_ADDR5 0x6050 +#define MX28_PAD_EMI_A06__EMI_ADDR6 0x6060 +#define MX28_PAD_EMI_A07__EMI_ADDR7 0x6070 +#define MX28_PAD_EMI_A08__EMI_ADDR8 0x6080 +#define MX28_PAD_EMI_A09__EMI_ADDR9 0x6090 +#define MX28_PAD_EMI_A10__EMI_ADDR10 0x60a0 +#define MX28_PAD_EMI_A11__EMI_ADDR11 0x60b0 +#define MX28_PAD_EMI_A12__EMI_ADDR12 0x60c0 +#define MX28_PAD_EMI_A13__EMI_ADDR13 0x60d0 +#define MX28_PAD_EMI_A14__EMI_ADDR14 0x60e0 +#define MX28_PAD_EMI_BA0__EMI_BA0 0x6100 +#define MX28_PAD_EMI_BA1__EMI_BA1 0x6110 +#define MX28_PAD_EMI_BA2__EMI_BA2 0x6120 +#define MX28_PAD_EMI_CASN__EMI_CASN 0x6130 +#define MX28_PAD_EMI_RASN__EMI_RASN 0x6140 +#define MX28_PAD_EMI_WEN__EMI_WEN 0x6150 +#define MX28_PAD_EMI_CE0N__EMI_CE0N 0x6160 +#define MX28_PAD_EMI_CE1N__EMI_CE1N 0x6170 +#define MX28_PAD_EMI_CKE__EMI_CKE 0x6180 +#define MX28_PAD_GPMI_D00__SSP1_D0 0x0001 +#define MX28_PAD_GPMI_D01__SSP1_D1 0x0011 +#define MX28_PAD_GPMI_D02__SSP1_D2 0x0021 +#define MX28_PAD_GPMI_D03__SSP1_D3 0x0031 +#define MX28_PAD_GPMI_D04__SSP1_D4 0x0041 +#define MX28_PAD_GPMI_D05__SSP1_D5 0x0051 +#define MX28_PAD_GPMI_D06__SSP1_D6 0x0061 +#define MX28_PAD_GPMI_D07__SSP1_D7 0x0071 +#define MX28_PAD_GPMI_CE0N__SSP3_D0 0x0101 +#define MX28_PAD_GPMI_CE1N__SSP3_D3 0x0111 +#define MX28_PAD_GPMI_CE2N__CAN1_TX 0x0121 +#define MX28_PAD_GPMI_CE3N__CAN1_RX 0x0131 +#define MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT 0x0141 +#define MX28_PAD_GPMI_RDY1__SSP1_CMD 0x0151 +#define MX28_PAD_GPMI_RDY2__CAN0_TX 0x0161 +#define MX28_PAD_GPMI_RDY3__CAN0_RX 0x0171 +#define MX28_PAD_GPMI_RDN__SSP3_SCK 0x0181 +#define MX28_PAD_GPMI_WRN__SSP1_SCK 0x0191 +#define MX28_PAD_GPMI_ALE__SSP3_D1 0x01a1 +#define MX28_PAD_GPMI_CLE__SSP3_D2 0x01b1 +#define MX28_PAD_GPMI_RESETN__SSP3_CMD 0x01c1 +#define MX28_PAD_LCD_D03__ETM_DA8 0x1031 +#define MX28_PAD_LCD_D04__ETM_DA9 0x1041 +#define MX28_PAD_LCD_D08__ETM_DA3 0x1081 +#define MX28_PAD_LCD_D09__ETM_DA4 0x1091 +#define MX28_PAD_LCD_D20__ENET1_1588_EVENT2_OUT 0x1141 +#define MX28_PAD_LCD_D21__ENET1_1588_EVENT2_IN 0x1151 +#define MX28_PAD_LCD_D22__ENET1_1588_EVENT3_OUT 0x1161 +#define MX28_PAD_LCD_D23__ENET1_1588_EVENT3_IN 0x1171 +#define MX28_PAD_LCD_RD_E__LCD_VSYNC 0x1181 +#define MX28_PAD_LCD_WR_RWN__LCD_HSYNC 0x1191 +#define MX28_PAD_LCD_RS__LCD_DOTCLK 0x11a1 +#define MX28_PAD_LCD_CS__LCD_ENABLE 0x11b1 +#define MX28_PAD_LCD_VSYNC__SAIF1_SDATA0 0x11c1 +#define MX28_PAD_LCD_HSYNC__SAIF1_SDATA1 0x11d1 +#define MX28_PAD_LCD_DOTCLK__SAIF1_MCLK 0x11e1 +#define MX28_PAD_SSP0_DATA4__SSP2_D0 0x2041 +#define MX28_PAD_SSP0_DATA5__SSP2_D3 0x2051 +#define MX28_PAD_SSP0_DATA6__SSP2_CMD 0x2061 +#define MX28_PAD_SSP0_DATA7__SSP2_SCK 0x2071 +#define MX28_PAD_SSP1_SCK__SSP2_D1 0x20c1 +#define MX28_PAD_SSP1_CMD__SSP2_D2 0x20d1 +#define MX28_PAD_SSP1_DATA0__SSP2_D6 0x20e1 +#define MX28_PAD_SSP1_DATA3__SSP2_D7 0x20f1 +#define MX28_PAD_SSP2_SCK__AUART2_RX 0x2101 +#define MX28_PAD_SSP2_MOSI__AUART2_TX 0x2111 +#define MX28_PAD_SSP2_MISO__AUART3_RX 0x2121 +#define MX28_PAD_SSP2_SS0__AUART3_TX 0x2131 +#define MX28_PAD_SSP2_SS1__SSP2_D1 0x2141 +#define MX28_PAD_SSP2_SS2__SSP2_D2 0x2151 +#define MX28_PAD_SSP3_SCK__AUART4_TX 0x2181 +#define MX28_PAD_SSP3_MOSI__AUART4_RX 0x2191 +#define MX28_PAD_SSP3_MISO__AUART4_RTS 0x21a1 +#define MX28_PAD_SSP3_SS0__AUART4_CTS 0x21b1 +#define MX28_PAD_AUART0_RX__I2C0_SCL 0x3001 +#define MX28_PAD_AUART0_TX__I2C0_SDA 0x3011 +#define MX28_PAD_AUART0_CTS__AUART4_RX 0x3021 +#define MX28_PAD_AUART0_RTS__AUART4_TX 0x3031 +#define MX28_PAD_AUART1_RX__SSP2_CARD_DETECT 0x3041 +#define MX28_PAD_AUART1_TX__SSP3_CARD_DETECT 0x3051 +#define MX28_PAD_AUART1_CTS__USB0_OVERCURRENT 0x3061 +#define MX28_PAD_AUART1_RTS__USB0_ID 0x3071 +#define MX28_PAD_AUART2_RX__SSP3_D1 0x3081 +#define MX28_PAD_AUART2_TX__SSP3_D2 0x3091 +#define MX28_PAD_AUART2_CTS__I2C1_SCL 0x30a1 +#define MX28_PAD_AUART2_RTS__I2C1_SDA 0x30b1 +#define MX28_PAD_AUART3_RX__CAN0_TX 0x30c1 +#define MX28_PAD_AUART3_TX__CAN0_RX 0x30d1 +#define MX28_PAD_AUART3_CTS__CAN1_TX 0x30e1 +#define MX28_PAD_AUART3_RTS__CAN1_RX 0x30f1 +#define MX28_PAD_PWM0__I2C1_SCL 0x3101 +#define MX28_PAD_PWM1__I2C1_SDA 0x3111 +#define MX28_PAD_PWM2__USB0_ID 0x3121 +#define MX28_PAD_SAIF0_MCLK__PWM_3 0x3141 +#define MX28_PAD_SAIF0_LRCLK__PWM_4 0x3151 +#define MX28_PAD_SAIF0_BITCLK__PWM_5 0x3161 +#define MX28_PAD_SAIF0_SDATA0__PWM_6 0x3171 +#define MX28_PAD_I2C0_SCL__TIMROT_ROTARYA 0x3181 +#define MX28_PAD_I2C0_SDA__TIMROT_ROTARYB 0x3191 +#define MX28_PAD_SAIF1_SDATA0__PWM_7 0x31a1 +#define MX28_PAD_LCD_RESET__LCD_VSYNC 0x31e1 +#define MX28_PAD_ENET0_MDC__GPMI_CE4N 0x4001 +#define MX28_PAD_ENET0_MDIO__GPMI_CE5N 0x4011 +#define MX28_PAD_ENET0_RX_EN__GPMI_CE6N 0x4021 +#define MX28_PAD_ENET0_RXD0__GPMI_CE7N 0x4031 +#define MX28_PAD_ENET0_RXD1__GPMI_READY4 0x4041 +#define MX28_PAD_ENET0_TX_CLK__HSADC_TRIGGER 0x4051 +#define MX28_PAD_ENET0_TX_EN__GPMI_READY5 0x4061 +#define MX28_PAD_ENET0_TXD0__GPMI_READY6 0x4071 +#define MX28_PAD_ENET0_TXD1__GPMI_READY7 0x4081 +#define MX28_PAD_ENET0_RXD2__ENET1_RXD0 0x4091 +#define MX28_PAD_ENET0_RXD3__ENET1_RXD1 0x40a1 +#define MX28_PAD_ENET0_TXD2__ENET1_TXD0 0x40b1 +#define MX28_PAD_ENET0_TXD3__ENET1_TXD1 0x40c1 +#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_ER 0x40d1 +#define MX28_PAD_ENET0_COL__ENET1_TX_EN 0x40e1 +#define MX28_PAD_ENET0_CRS__ENET1_RX_EN 0x40f1 +#define MX28_PAD_GPMI_CE2N__ENET0_RX_ER 0x0122 +#define MX28_PAD_GPMI_CE3N__SAIF1_MCLK 0x0132 +#define MX28_PAD_GPMI_RDY0__USB0_ID 0x0142 +#define MX28_PAD_GPMI_RDY2__ENET0_TX_ER 0x0162 +#define MX28_PAD_GPMI_RDY3__HSADC_TRIGGER 0x0172 +#define MX28_PAD_GPMI_ALE__SSP3_D4 0x01a2 +#define MX28_PAD_GPMI_CLE__SSP3_D5 0x01b2 +#define MX28_PAD_LCD_D00__ETM_DA0 0x1002 +#define MX28_PAD_LCD_D01__ETM_DA1 0x1012 +#define MX28_PAD_LCD_D02__ETM_DA2 0x1022 +#define MX28_PAD_LCD_D03__ETM_DA3 0x1032 +#define MX28_PAD_LCD_D04__ETM_DA4 0x1042 +#define MX28_PAD_LCD_D05__ETM_DA5 0x1052 +#define MX28_PAD_LCD_D06__ETM_DA6 0x1062 +#define MX28_PAD_LCD_D07__ETM_DA7 0x1072 +#define MX28_PAD_LCD_D08__ETM_DA8 0x1082 +#define MX28_PAD_LCD_D09__ETM_DA9 0x1092 +#define MX28_PAD_LCD_D10__ETM_DA10 0x10a2 +#define MX28_PAD_LCD_D11__ETM_DA11 0x10b2 +#define MX28_PAD_LCD_D12__ETM_DA12 0x10c2 +#define MX28_PAD_LCD_D13__ETM_DA13 0x10d2 +#define MX28_PAD_LCD_D14__ETM_DA14 0x10e2 +#define MX28_PAD_LCD_D15__ETM_DA15 0x10f2 +#define MX28_PAD_LCD_D16__ETM_DA7 0x1102 +#define MX28_PAD_LCD_D17__ETM_DA6 0x1112 +#define MX28_PAD_LCD_D18__ETM_DA5 0x1122 +#define MX28_PAD_LCD_D19__ETM_DA4 0x1132 +#define MX28_PAD_LCD_D20__ETM_DA3 0x1142 +#define MX28_PAD_LCD_D21__ETM_DA2 0x1152 +#define MX28_PAD_LCD_D22__ETM_DA1 0x1162 +#define MX28_PAD_LCD_D23__ETM_DA0 0x1172 +#define MX28_PAD_LCD_RD_E__ETM_TCTL 0x1182 +#define MX28_PAD_LCD_WR_RWN__ETM_TCLK 0x1192 +#define MX28_PAD_LCD_HSYNC__ETM_TCTL 0x11d2 +#define MX28_PAD_LCD_DOTCLK__ETM_TCLK 0x11e2 +#define MX28_PAD_SSP1_SCK__ENET0_1588_EVENT2_OUT 0x20c2 +#define MX28_PAD_SSP1_CMD__ENET0_1588_EVENT2_IN 0x20d2 +#define MX28_PAD_SSP1_DATA0__ENET0_1588_EVENT3_OUT 0x20e2 +#define MX28_PAD_SSP1_DATA3__ENET0_1588_EVENT3_IN 0x20f2 +#define MX28_PAD_SSP2_SCK__SAIF0_SDATA1 0x2102 +#define MX28_PAD_SSP2_MOSI__SAIF0_SDATA2 0x2112 +#define MX28_PAD_SSP2_MISO__SAIF1_SDATA1 0x2122 +#define MX28_PAD_SSP2_SS0__SAIF1_SDATA2 0x2132 +#define MX28_PAD_SSP2_SS1__USB1_OVERCURRENT 0x2142 +#define MX28_PAD_SSP2_SS2__USB0_OVERCURRENT 0x2152 +#define MX28_PAD_SSP3_SCK__ENET1_1588_EVENT0_OUT 0x2182 +#define MX28_PAD_SSP3_MOSI__ENET1_1588_EVENT0_IN 0x2192 +#define MX28_PAD_SSP3_MISO__ENET1_1588_EVENT1_OUT 0x21a2 +#define MX28_PAD_SSP3_SS0__ENET1_1588_EVENT1_IN 0x21b2 +#define MX28_PAD_AUART0_RX__DUART_CTS 0x3002 +#define MX28_PAD_AUART0_TX__DUART_RTS 0x3012 +#define MX28_PAD_AUART0_CTS__DUART_RX 0x3022 +#define MX28_PAD_AUART0_RTS__DUART_TX 0x3032 +#define MX28_PAD_AUART1_RX__PWM_0 0x3042 +#define MX28_PAD_AUART1_TX__PWM_1 0x3052 +#define MX28_PAD_AUART1_CTS__TIMROT_ROTARYA 0x3062 +#define MX28_PAD_AUART1_RTS__TIMROT_ROTARYB 0x3072 +#define MX28_PAD_AUART2_RX__SSP3_D4 0x3082 +#define MX28_PAD_AUART2_TX__SSP3_D5 0x3092 +#define MX28_PAD_AUART2_CTS__SAIF1_BITCLK 0x30a2 +#define MX28_PAD_AUART2_RTS__SAIF1_LRCLK 0x30b2 +#define MX28_PAD_AUART3_RX__ENET0_1588_EVENT0_OUT 0x30c2 +#define MX28_PAD_AUART3_TX__ENET0_1588_EVENT0_IN 0x30d2 +#define MX28_PAD_AUART3_CTS__ENET0_1588_EVENT1_OUT 0x30e2 +#define MX28_PAD_AUART3_RTS__ENET0_1588_EVENT1_IN 0x30f2 +#define MX28_PAD_PWM0__DUART_RX 0x3102 +#define MX28_PAD_PWM1__DUART_TX 0x3112 +#define MX28_PAD_PWM2__USB1_OVERCURRENT 0x3122 +#define MX28_PAD_SAIF0_MCLK__AUART4_CTS 0x3142 +#define MX28_PAD_SAIF0_LRCLK__AUART4_RTS 0x3152 +#define MX28_PAD_SAIF0_BITCLK__AUART4_RX 0x3162 +#define MX28_PAD_SAIF0_SDATA0__AUART4_TX 0x3172 +#define MX28_PAD_I2C0_SCL__DUART_RX 0x3182 +#define MX28_PAD_I2C0_SDA__DUART_TX 0x3192 +#define MX28_PAD_SAIF1_SDATA0__SAIF0_SDATA1 0x31a2 +#define MX28_PAD_SPDIF__ENET1_RX_ER 0x31b2 +#define MX28_PAD_ENET0_MDC__SAIF0_SDATA1 0x4002 +#define MX28_PAD_ENET0_MDIO__SAIF0_SDATA2 0x4012 +#define MX28_PAD_ENET0_RX_EN__SAIF1_SDATA1 0x4022 +#define MX28_PAD_ENET0_RXD0__SAIF1_SDATA2 0x4032 +#define MX28_PAD_ENET0_TX_CLK__ENET0_1588_EVENT2_OUT 0x4052 +#define MX28_PAD_ENET0_RXD2__ENET0_1588_EVENT0_OUT 0x4092 +#define MX28_PAD_ENET0_RXD3__ENET0_1588_EVENT0_IN 0x40a2 +#define MX28_PAD_ENET0_TXD2__ENET0_1588_EVENT1_OUT 0x40b2 +#define MX28_PAD_ENET0_TXD3__ENET0_1588_EVENT1_IN 0x40c2 +#define MX28_PAD_ENET0_RX_CLK__ENET0_1588_EVENT2_IN 0x40d2 +#define MX28_PAD_ENET0_COL__ENET0_1588_EVENT3_OUT 0x40e2 +#define MX28_PAD_ENET0_CRS__ENET0_1588_EVENT3_IN 0x40f2 +#define MX28_PAD_GPMI_D00__GPIO_0_0 0x0003 +#define MX28_PAD_GPMI_D01__GPIO_0_1 0x0013 +#define MX28_PAD_GPMI_D02__GPIO_0_2 0x0023 +#define MX28_PAD_GPMI_D03__GPIO_0_3 0x0033 +#define MX28_PAD_GPMI_D04__GPIO_0_4 0x0043 +#define MX28_PAD_GPMI_D05__GPIO_0_5 0x0053 +#define MX28_PAD_GPMI_D06__GPIO_0_6 0x0063 +#define MX28_PAD_GPMI_D07__GPIO_0_7 0x0073 +#define MX28_PAD_GPMI_CE0N__GPIO_0_16 0x0103 +#define MX28_PAD_GPMI_CE1N__GPIO_0_17 0x0113 +#define MX28_PAD_GPMI_CE2N__GPIO_0_18 0x0123 +#define MX28_PAD_GPMI_CE3N__GPIO_0_19 0x0133 +#define MX28_PAD_GPMI_RDY0__GPIO_0_20 0x0143 +#define MX28_PAD_GPMI_RDY1__GPIO_0_21 0x0153 +#define MX28_PAD_GPMI_RDY2__GPIO_0_22 0x0163 +#define MX28_PAD_GPMI_RDY3__GPIO_0_23 0x0173 +#define MX28_PAD_GPMI_RDN__GPIO_0_24 0x0183 +#define MX28_PAD_GPMI_WRN__GPIO_0_25 0x0193 +#define MX28_PAD_GPMI_ALE__GPIO_0_26 0x01a3 +#define MX28_PAD_GPMI_CLE__GPIO_0_27 0x01b3 +#define MX28_PAD_GPMI_RESETN__GPIO_0_28 0x01c3 +#define MX28_PAD_LCD_D00__GPIO_1_0 0x1003 +#define MX28_PAD_LCD_D01__GPIO_1_1 0x1013 +#define MX28_PAD_LCD_D02__GPIO_1_2 0x1023 +#define MX28_PAD_LCD_D03__GPIO_1_3 0x1033 +#define MX28_PAD_LCD_D04__GPIO_1_4 0x1043 +#define MX28_PAD_LCD_D05__GPIO_1_5 0x1053 +#define MX28_PAD_LCD_D06__GPIO_1_6 0x1063 +#define MX28_PAD_LCD_D07__GPIO_1_7 0x1073 +#define MX28_PAD_LCD_D08__GPIO_1_8 0x1083 +#define MX28_PAD_LCD_D09__GPIO_1_9 0x1093 +#define MX28_PAD_LCD_D10__GPIO_1_10 0x10a3 +#define MX28_PAD_LCD_D11__GPIO_1_11 0x10b3 +#define MX28_PAD_LCD_D12__GPIO_1_12 0x10c3 +#define MX28_PAD_LCD_D13__GPIO_1_13 0x10d3 +#define MX28_PAD_LCD_D14__GPIO_1_14 0x10e3 +#define MX28_PAD_LCD_D15__GPIO_1_15 0x10f3 +#define MX28_PAD_LCD_D16__GPIO_1_16 0x1103 +#define MX28_PAD_LCD_D17__GPIO_1_17 0x1113 +#define MX28_PAD_LCD_D18__GPIO_1_18 0x1123 +#define MX28_PAD_LCD_D19__GPIO_1_19 0x1133 +#define MX28_PAD_LCD_D20__GPIO_1_20 0x1143 +#define MX28_PAD_LCD_D21__GPIO_1_21 0x1153 +#define MX28_PAD_LCD_D22__GPIO_1_22 0x1163 +#define MX28_PAD_LCD_D23__GPIO_1_23 0x1173 +#define MX28_PAD_LCD_RD_E__GPIO_1_24 0x1183 +#define MX28_PAD_LCD_WR_RWN__GPIO_1_25 0x1193 +#define MX28_PAD_LCD_RS__GPIO_1_26 0x11a3 +#define MX28_PAD_LCD_CS__GPIO_1_27 0x11b3 +#define MX28_PAD_LCD_VSYNC__GPIO_1_28 0x11c3 +#define MX28_PAD_LCD_HSYNC__GPIO_1_29 0x11d3 +#define MX28_PAD_LCD_DOTCLK__GPIO_1_30 0x11e3 +#define MX28_PAD_LCD_ENABLE__GPIO_1_31 0x11f3 +#define MX28_PAD_SSP0_DATA0__GPIO_2_0 0x2003 +#define MX28_PAD_SSP0_DATA1__GPIO_2_1 0x2013 +#define MX28_PAD_SSP0_DATA2__GPIO_2_2 0x2023 +#define MX28_PAD_SSP0_DATA3__GPIO_2_3 0x2033 +#define MX28_PAD_SSP0_DATA4__GPIO_2_4 0x2043 +#define MX28_PAD_SSP0_DATA5__GPIO_2_5 0x2053 +#define MX28_PAD_SSP0_DATA6__GPIO_2_6 0x2063 +#define MX28_PAD_SSP0_DATA7__GPIO_2_7 0x2073 +#define MX28_PAD_SSP0_CMD__GPIO_2_8 0x2083 +#define MX28_PAD_SSP0_DETECT__GPIO_2_9 0x2093 +#define MX28_PAD_SSP0_SCK__GPIO_2_10 0x20a3 +#define MX28_PAD_SSP1_SCK__GPIO_2_12 0x20c3 +#define MX28_PAD_SSP1_CMD__GPIO_2_13 0x20d3 +#define MX28_PAD_SSP1_DATA0__GPIO_2_14 0x20e3 +#define MX28_PAD_SSP1_DATA3__GPIO_2_15 0x20f3 +#define MX28_PAD_SSP2_SCK__GPIO_2_16 0x2103 +#define MX28_PAD_SSP2_MOSI__GPIO_2_17 0x2113 +#define MX28_PAD_SSP2_MISO__GPIO_2_18 0x2123 +#define MX28_PAD_SSP2_SS0__GPIO_2_19 0x2133 +#define MX28_PAD_SSP2_SS1__GPIO_2_20 0x2143 +#define MX28_PAD_SSP2_SS2__GPIO_2_21 0x2153 +#define MX28_PAD_SSP3_SCK__GPIO_2_24 0x2183 +#define MX28_PAD_SSP3_MOSI__GPIO_2_25 0x2193 +#define MX28_PAD_SSP3_MISO__GPIO_2_26 0x21a3 +#define MX28_PAD_SSP3_SS0__GPIO_2_27 0x21b3 +#define MX28_PAD_AUART0_RX__GPIO_3_0 0x3003 +#define MX28_PAD_AUART0_TX__GPIO_3_1 0x3013 +#define MX28_PAD_AUART0_CTS__GPIO_3_2 0x3023 +#define MX28_PAD_AUART0_RTS__GPIO_3_3 0x3033 +#define MX28_PAD_AUART1_RX__GPIO_3_4 0x3043 +#define MX28_PAD_AUART1_TX__GPIO_3_5 0x3053 +#define MX28_PAD_AUART1_CTS__GPIO_3_6 0x3063 +#define MX28_PAD_AUART1_RTS__GPIO_3_7 0x3073 +#define MX28_PAD_AUART2_RX__GPIO_3_8 0x3083 +#define MX28_PAD_AUART2_TX__GPIO_3_9 0x3093 +#define MX28_PAD_AUART2_CTS__GPIO_3_10 0x30a3 +#define MX28_PAD_AUART2_RTS__GPIO_3_11 0x30b3 +#define MX28_PAD_AUART3_RX__GPIO_3_12 0x30c3 +#define MX28_PAD_AUART3_TX__GPIO_3_13 0x30d3 +#define MX28_PAD_AUART3_CTS__GPIO_3_14 0x30e3 +#define MX28_PAD_AUART3_RTS__GPIO_3_15 0x30f3 +#define MX28_PAD_PWM0__GPIO_3_16 0x3103 +#define MX28_PAD_PWM1__GPIO_3_17 0x3113 +#define MX28_PAD_PWM2__GPIO_3_18 0x3123 +#define MX28_PAD_SAIF0_MCLK__GPIO_3_20 0x3143 +#define MX28_PAD_SAIF0_LRCLK__GPIO_3_21 0x3153 +#define MX28_PAD_SAIF0_BITCLK__GPIO_3_22 0x3163 +#define MX28_PAD_SAIF0_SDATA0__GPIO_3_23 0x3173 +#define MX28_PAD_I2C0_SCL__GPIO_3_24 0x3183 +#define MX28_PAD_I2C0_SDA__GPIO_3_25 0x3193 +#define MX28_PAD_SAIF1_SDATA0__GPIO_3_26 0x31a3 +#define MX28_PAD_SPDIF__GPIO_3_27 0x31b3 +#define MX28_PAD_PWM3__GPIO_3_28 0x31c3 +#define MX28_PAD_PWM4__GPIO_3_29 0x31d3 +#define MX28_PAD_LCD_RESET__GPIO_3_30 0x31e3 +#define MX28_PAD_ENET0_MDC__GPIO_4_0 0x4003 +#define MX28_PAD_ENET0_MDIO__GPIO_4_1 0x4013 +#define MX28_PAD_ENET0_RX_EN__GPIO_4_2 0x4023 +#define MX28_PAD_ENET0_RXD0__GPIO_4_3 0x4033 +#define MX28_PAD_ENET0_RXD1__GPIO_4_4 0x4043 +#define MX28_PAD_ENET0_TX_CLK__GPIO_4_5 0x4053 +#define MX28_PAD_ENET0_TX_EN__GPIO_4_6 0x4063 +#define MX28_PAD_ENET0_TXD0__GPIO_4_7 0x4073 +#define MX28_PAD_ENET0_TXD1__GPIO_4_8 0x4083 +#define MX28_PAD_ENET0_RXD2__GPIO_4_9 0x4093 +#define MX28_PAD_ENET0_RXD3__GPIO_4_10 0x40a3 +#define MX28_PAD_ENET0_TXD2__GPIO_4_11 0x40b3 +#define MX28_PAD_ENET0_TXD3__GPIO_4_12 0x40c3 +#define MX28_PAD_ENET0_RX_CLK__GPIO_4_13 0x40d3 +#define MX28_PAD_ENET0_COL__GPIO_4_14 0x40e3 +#define MX28_PAD_ENET0_CRS__GPIO_4_15 0x40f3 +#define MX28_PAD_ENET_CLK__GPIO_4_16 0x4103 +#define MX28_PAD_JTAG_RTCK__GPIO_4_20 0x4143 + +#endif /* __DT_BINDINGS_MX28_PINCTRL_H__ */ diff --git a/arch/arm/dts/imx28.dtsi b/arch/arm/dts/imx28.dtsi new file mode 100644 index 0000000000..e14d8ef015 --- /dev/null +++ b/arch/arm/dts/imx28.dtsi @@ -0,0 +1,1330 @@ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2012 Freescale Semiconductor, Inc. + +#include <dt-bindings/gpio/gpio.h> +#include "imx28-pinfunc.h" + +/ { + #address-cells = <1>; + #size-cells = <1>; + + interrupt-parent = <&icoll>; + /* + * The decompressor and also some bootloaders rely on a + * pre-existing /chosen node to be available to insert the + * command line and merge other ATAGS info. + */ + chosen {}; + + aliases { + ethernet0 = &mac0; + ethernet1 = &mac1; + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + gpio4 = &gpio4; + saif0 = &saif0; + saif1 = &saif1; + serial0 = &auart0; + serial1 = &auart1; + serial2 = &auart2; + serial3 = &auart3; + serial4 = &auart4; + spi0 = &ssp1; + spi1 = &ssp2; + usbphy0 = &usbphy0; + usbphy1 = &usbphy1; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,arm926ej-s"; + device_type = "cpu"; + reg = <0>; + }; + }; + + apb@80000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x80000000 0x80000>; + ranges; + + apbh@80000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x80000000 0x3c900>; + ranges; + + icoll: interrupt-controller@80000000 { + compatible = "fsl,imx28-icoll", "fsl,icoll"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x80000000 0x2000>; + }; + + hsadc: hsadc@80002000 { + reg = <0x80002000 0x2000>; + interrupts = <13>; + dmas = <&dma_apbh 12>; + dma-names = "rx"; + status = "disabled"; + }; + + dma_apbh: dma-apbh@80004000 { + compatible = "fsl,imx28-dma-apbh"; + reg = <0x80004000 0x2000>; + interrupts = <82 83 84 85 + 88 88 88 88 + 88 88 88 88 + 87 86 0 0>; + interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3", + "gpmi0", "gmpi1", "gpmi2", "gmpi3", + "gpmi4", "gmpi5", "gpmi6", "gmpi7", + "hsadc", "lcdif", "empty", "empty"; + #dma-cells = <1>; + dma-channels = <16>; + clocks = <&clks 25>; + }; + + perfmon: perfmon@80006000 { + reg = <0x80006000 0x800>; + interrupts = <27>; + status = "disabled"; + }; + + gpmi: gpmi-nand@8000c000 { + compatible = "fsl,imx28-gpmi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x8000c000 0x2000>, <0x8000a000 0x2000>; + reg-names = "gpmi-nand", "bch"; + interrupts = <41>; + interrupt-names = "bch"; + clocks = <&clks 50>; + clock-names = "gpmi_io"; + dmas = <&dma_apbh 4>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + ssp0: spi@80010000 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x80010000 0x2000>; + interrupts = <96>; + clocks = <&clks 46>; + dmas = <&dma_apbh 0>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + ssp1: spi@80012000 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x80012000 0x2000>; + interrupts = <97>; + clocks = <&clks 47>; + dmas = <&dma_apbh 1>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + ssp2: spi@80014000 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x80014000 0x2000>; + interrupts = <98>; + clocks = <&clks 48>; + dmas = <&dma_apbh 2>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + ssp3: spi@80016000 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x80016000 0x2000>; + interrupts = <99>; + clocks = <&clks 49>; + dmas = <&dma_apbh 3>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + pinctrl: pinctrl@80018000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-pinctrl", "simple-bus"; + reg = <0x80018000 0x2000>; + + gpio0: gpio@0 { + compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; + reg = <0>; + interrupts = <127>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@1 { + compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; + reg = <1>; + interrupts = <126>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@2 { + compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; + reg = <2>; + interrupts = <125>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@3 { + compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; + reg = <3>; + interrupts = <124>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@4 { + compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; + reg = <4>; + interrupts = <123>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + duart_pins_a: duart@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM0__DUART_RX + MX28_PAD_PWM1__DUART_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + duart_pins_b: duart@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_CTS__DUART_RX + MX28_PAD_AUART0_RTS__DUART_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + duart_4pins_a: duart-4pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_CTS__DUART_RX + MX28_PAD_AUART0_RTS__DUART_TX + MX28_PAD_AUART0_RX__DUART_CTS + MX28_PAD_AUART0_TX__DUART_RTS + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + gpmi_pins_a: gpmi-nand@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_D00__GPMI_D0 + MX28_PAD_GPMI_D01__GPMI_D1 + MX28_PAD_GPMI_D02__GPMI_D2 + MX28_PAD_GPMI_D03__GPMI_D3 + MX28_PAD_GPMI_D04__GPMI_D4 + MX28_PAD_GPMI_D05__GPMI_D5 + MX28_PAD_GPMI_D06__GPMI_D6 + MX28_PAD_GPMI_D07__GPMI_D7 + MX28_PAD_GPMI_CE0N__GPMI_CE0N + MX28_PAD_GPMI_RDY0__GPMI_READY0 + MX28_PAD_GPMI_RDN__GPMI_RDN + MX28_PAD_GPMI_WRN__GPMI_WRN + MX28_PAD_GPMI_ALE__GPMI_ALE + MX28_PAD_GPMI_CLE__GPMI_CLE + MX28_PAD_GPMI_RESETN__GPMI_RESETN + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + gpmi_status_cfg: gpmi-status-cfg@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_RDN__GPMI_RDN + MX28_PAD_GPMI_WRN__GPMI_WRN + MX28_PAD_GPMI_RESETN__GPMI_RESETN + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + }; + + auart0_pins_a: auart0@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_RX__AUART0_RX + MX28_PAD_AUART0_TX__AUART0_TX + MX28_PAD_AUART0_CTS__AUART0_CTS + MX28_PAD_AUART0_RTS__AUART0_RTS + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart0_2pins_a: auart0-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_RX__AUART0_RX + MX28_PAD_AUART0_TX__AUART0_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart1_pins_a: auart1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_RX__AUART1_RX + MX28_PAD_AUART1_TX__AUART1_TX + MX28_PAD_AUART1_CTS__AUART1_CTS + MX28_PAD_AUART1_RTS__AUART1_RTS + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart1_2pins_a: auart1-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_RX__AUART1_RX + MX28_PAD_AUART1_TX__AUART1_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart2_2pins_a: auart2-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_SCK__AUART2_RX + MX28_PAD_SSP2_MOSI__AUART2_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart2_2pins_b: auart2-2pins@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART2_RX__AUART2_RX + MX28_PAD_AUART2_TX__AUART2_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart2_pins_a: auart2-pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART2_RX__AUART2_RX + MX28_PAD_AUART2_TX__AUART2_TX + MX28_PAD_AUART2_CTS__AUART2_CTS + MX28_PAD_AUART2_RTS__AUART2_RTS + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart3_pins_a: auart3@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART3_RX__AUART3_RX + MX28_PAD_AUART3_TX__AUART3_TX + MX28_PAD_AUART3_CTS__AUART3_CTS + MX28_PAD_AUART3_RTS__AUART3_RTS + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart3_2pins_a: auart3-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_MISO__AUART3_RX + MX28_PAD_SSP2_SS0__AUART3_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart3_2pins_b: auart3-2pins@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART3_RX__AUART3_RX + MX28_PAD_AUART3_TX__AUART3_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart4_2pins_a: auart4@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP3_SCK__AUART4_TX + MX28_PAD_SSP3_MOSI__AUART4_RX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + auart4_2pins_b: auart4@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_CTS__AUART4_RX + MX28_PAD_AUART0_RTS__AUART4_TX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mac0_pins_a: mac0@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_MDC__ENET0_MDC + MX28_PAD_ENET0_MDIO__ENET0_MDIO + MX28_PAD_ENET0_RX_EN__ENET0_RX_EN + MX28_PAD_ENET0_RXD0__ENET0_RXD0 + MX28_PAD_ENET0_RXD1__ENET0_RXD1 + MX28_PAD_ENET0_TX_EN__ENET0_TX_EN + MX28_PAD_ENET0_TXD0__ENET0_TXD0 + MX28_PAD_ENET0_TXD1__ENET0_TXD1 + MX28_PAD_ENET_CLK__CLKCTRL_ENET + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mac0_pins_b: mac0@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_MDC__ENET0_MDC + MX28_PAD_ENET0_MDIO__ENET0_MDIO + MX28_PAD_ENET0_RX_EN__ENET0_RX_EN + MX28_PAD_ENET0_RXD0__ENET0_RXD0 + MX28_PAD_ENET0_RXD1__ENET0_RXD1 + MX28_PAD_ENET0_RXD2__ENET0_RXD2 + MX28_PAD_ENET0_RXD3__ENET0_RXD3 + MX28_PAD_ENET0_TX_EN__ENET0_TX_EN + MX28_PAD_ENET0_TXD0__ENET0_TXD0 + MX28_PAD_ENET0_TXD1__ENET0_TXD1 + MX28_PAD_ENET0_TXD2__ENET0_TXD2 + MX28_PAD_ENET0_TXD3__ENET0_TXD3 + MX28_PAD_ENET_CLK__CLKCTRL_ENET + MX28_PAD_ENET0_COL__ENET0_COL + MX28_PAD_ENET0_CRS__ENET0_CRS + MX28_PAD_ENET0_TX_CLK__ENET0_TX_CLK + MX28_PAD_ENET0_RX_CLK__ENET0_RX_CLK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mac1_pins_a: mac1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_CRS__ENET1_RX_EN + MX28_PAD_ENET0_RXD2__ENET1_RXD0 + MX28_PAD_ENET0_RXD3__ENET1_RXD1 + MX28_PAD_ENET0_COL__ENET1_TX_EN + MX28_PAD_ENET0_TXD2__ENET1_TXD0 + MX28_PAD_ENET0_TXD3__ENET1_TXD1 + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc0_8bit_pins_a: mmc0-8bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA0__SSP0_D0 + MX28_PAD_SSP0_DATA1__SSP0_D1 + MX28_PAD_SSP0_DATA2__SSP0_D2 + MX28_PAD_SSP0_DATA3__SSP0_D3 + MX28_PAD_SSP0_DATA4__SSP0_D4 + MX28_PAD_SSP0_DATA5__SSP0_D5 + MX28_PAD_SSP0_DATA6__SSP0_D6 + MX28_PAD_SSP0_DATA7__SSP0_D7 + MX28_PAD_SSP0_CMD__SSP0_CMD + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + MX28_PAD_SSP0_SCK__SSP0_SCK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc0_4bit_pins_a: mmc0-4bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA0__SSP0_D0 + MX28_PAD_SSP0_DATA1__SSP0_D1 + MX28_PAD_SSP0_DATA2__SSP0_D2 + MX28_PAD_SSP0_DATA3__SSP0_D3 + MX28_PAD_SSP0_CMD__SSP0_CMD + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + MX28_PAD_SSP0_SCK__SSP0_SCK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc0_cd_cfg: mmc0-cd-cfg@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + >; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc0_sck_cfg: mmc0-sck-cfg@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_SCK__SSP0_SCK + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc1_4bit_pins_a: mmc1-4bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_D00__SSP1_D0 + MX28_PAD_GPMI_D01__SSP1_D1 + MX28_PAD_GPMI_D02__SSP1_D2 + MX28_PAD_GPMI_D03__SSP1_D3 + MX28_PAD_GPMI_RDY1__SSP1_CMD + MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT + MX28_PAD_GPMI_WRN__SSP1_SCK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc1_cd_cfg: mmc1-cd-cfg@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT + >; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc1_sck_cfg: mmc1-sck-cfg@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_WRN__SSP1_SCK + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + + mmc2_4bit_pins_a: mmc2-4bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA4__SSP2_D0 + MX28_PAD_SSP1_SCK__SSP2_D1 + MX28_PAD_SSP1_CMD__SSP2_D2 + MX28_PAD_SSP0_DATA5__SSP2_D3 + MX28_PAD_SSP0_DATA6__SSP2_CMD + MX28_PAD_AUART1_RX__SSP2_CARD_DETECT + MX28_PAD_SSP0_DATA7__SSP2_SCK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc2_4bit_pins_b: mmc2-4bit@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_SCK__SSP2_SCK + MX28_PAD_SSP2_MOSI__SSP2_CMD + MX28_PAD_SSP2_MISO__SSP2_D0 + MX28_PAD_SSP2_SS0__SSP2_D3 + MX28_PAD_SSP2_SS1__SSP2_D1 + MX28_PAD_SSP2_SS2__SSP2_D2 + MX28_PAD_AUART1_RX__SSP2_CARD_DETECT + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc2_cd_cfg: mmc2-cd-cfg@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_RX__SSP2_CARD_DETECT + >; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc2_sck_cfg_a: mmc2-sck-cfg@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA7__SSP2_SCK + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc2_sck_cfg_b: mmc2-sck-cfg@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_SCK__SSP2_SCK + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + i2c0_pins_a: i2c0@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_I2C0_SCL__I2C0_SCL + MX28_PAD_I2C0_SDA__I2C0_SDA + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + i2c0_pins_b: i2c0@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_RX__I2C0_SCL + MX28_PAD_AUART0_TX__I2C0_SDA + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + i2c1_pins_a: i2c1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM0__I2C1_SCL + MX28_PAD_PWM1__I2C1_SDA + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + i2c1_pins_b: i2c1@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART2_CTS__I2C1_SCL + MX28_PAD_AUART2_RTS__I2C1_SDA + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + saif0_pins_a: saif0@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SAIF0_MCLK__SAIF0_MCLK + MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK + MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK + MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + saif0_pins_b: saif0@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK + MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK + MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + saif1_pins_a: saif1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + pwm0_pins_a: pwm0@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM0__PWM_0 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + pwm2_pins_a: pwm2@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM2__PWM_2 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + pwm3_pins_a: pwm3@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM3__PWM_3 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + pwm3_pins_b: pwm3@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_SAIF0_MCLK__PWM_3 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + pwm4_pins_a: pwm4@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM4__PWM_4 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_24bit_pins_a: lcdif-24bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 + MX28_PAD_LCD_D18__LCD_D18 + MX28_PAD_LCD_D19__LCD_D19 + MX28_PAD_LCD_D20__LCD_D20 + MX28_PAD_LCD_D21__LCD_D21 + MX28_PAD_LCD_D22__LCD_D22 + MX28_PAD_LCD_D23__LCD_D23 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_18bit_pins_a: lcdif-18bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_16bit_pins_a: lcdif-16bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_sync_pins_a: lcdif-sync@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + can0_pins_a: can0@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_RDY2__CAN0_TX + MX28_PAD_GPMI_RDY3__CAN0_RX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + can1_pins_a: can1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_CE2N__CAN1_TX + MX28_PAD_GPMI_CE3N__CAN1_RX + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + spi2_pins_a: spi2@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_SCK__SSP2_SCK + MX28_PAD_SSP2_MOSI__SSP2_CMD + MX28_PAD_SSP2_MISO__SSP2_D0 + MX28_PAD_SSP2_SS0__SSP2_D3 + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + spi3_pins_a: spi3@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART2_RX__SSP3_D4 + MX28_PAD_AUART2_TX__SSP3_D5 + MX28_PAD_SSP3_SCK__SSP3_SCK + MX28_PAD_SSP3_MOSI__SSP3_CMD + MX28_PAD_SSP3_MISO__SSP3_D0 + MX28_PAD_SSP3_SS0__SSP3_D3 + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + spi3_pins_b: spi3@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_SSP3_SCK__SSP3_SCK + MX28_PAD_SSP3_MOSI__SSP3_CMD + MX28_PAD_SSP3_MISO__SSP3_D0 + MX28_PAD_SSP3_SS0__SSP3_D3 + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + usb0_pins_a: usb0@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_SS2__USB0_OVERCURRENT + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + usb0_pins_b: usb0@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_CTS__USB0_OVERCURRENT + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + usb1_pins_a: usb1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_SS1__USB1_OVERCURRENT + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + usb0_id_pins_a: usb0id@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_RTS__USB0_ID + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + usb0_id_pins_b: usb0id1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM2__USB0_ID + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + }; + + digctl: digctl@8001c000 { + compatible = "fsl,imx28-digctl", "fsl,imx23-digctl"; + reg = <0x8001c000 0x2000>; + interrupts = <89>; + status = "disabled"; + }; + + etm: etm@80022000 { + reg = <0x80022000 0x2000>; + status = "disabled"; + }; + + dma_apbx: dma-apbx@80024000 { + compatible = "fsl,imx28-dma-apbx"; + reg = <0x80024000 0x2000>; + interrupts = <78 79 66 0 + 80 81 68 69 + 70 71 72 73 + 74 75 76 77>; + interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty", + "saif0", "saif1", "i2c0", "i2c1", + "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", + "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; + #dma-cells = <1>; + dma-channels = <16>; + clocks = <&clks 26>; + }; + + dcp: dcp@80028000 { + compatible = "fsl,imx28-dcp", "fsl,imx23-dcp"; + reg = <0x80028000 0x2000>; + interrupts = <52 53 54>; + status = "okay"; + }; + + pxp: pxp@8002a000 { + reg = <0x8002a000 0x2000>; + interrupts = <39>; + status = "disabled"; + }; + + ocotp: ocotp@8002c000 { + compatible = "fsl,imx28-ocotp", "fsl,ocotp"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x8002c000 0x2000>; + clocks = <&clks 25>; + }; + + axi-ahb@8002e000 { + reg = <0x8002e000 0x2000>; + status = "disabled"; + }; + + lcdif: lcdif@80030000 { + compatible = "fsl,imx28-lcdif"; + reg = <0x80030000 0x2000>; + interrupts = <38>; + clocks = <&clks 55>; + dmas = <&dma_apbh 13>; + dma-names = "rx"; + status = "disabled"; + }; + + can0: can@80032000 { + compatible = "fsl,imx28-flexcan"; + reg = <0x80032000 0x2000>; + interrupts = <8>; + clocks = <&clks 58>, <&clks 58>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + can1: can@80034000 { + compatible = "fsl,imx28-flexcan"; + reg = <0x80034000 0x2000>; + interrupts = <9>; + clocks = <&clks 59>, <&clks 59>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + simdbg: simdbg@8003c000 { + reg = <0x8003c000 0x200>; + status = "disabled"; + }; + + simgpmisel: simgpmisel@8003c200 { + reg = <0x8003c200 0x100>; + status = "disabled"; + }; + + simsspsel: simsspsel@8003c300 { + reg = <0x8003c300 0x100>; + status = "disabled"; + }; + + simmemsel: simmemsel@8003c400 { + reg = <0x8003c400 0x100>; + status = "disabled"; + }; + + gpiomon: gpiomon@8003c500 { + reg = <0x8003c500 0x100>; + status = "disabled"; + }; + + simenet: simenet@8003c700 { + reg = <0x8003c700 0x100>; + status = "disabled"; + }; + + armjtag: armjtag@8003c800 { + reg = <0x8003c800 0x100>; + status = "disabled"; + }; + }; + + apbx@80040000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x80040000 0x40000>; + ranges; + + clks: clkctrl@80040000 { + compatible = "fsl,imx28-clkctrl", "fsl,clkctrl"; + reg = <0x80040000 0x2000>; + #clock-cells = <1>; + }; + + saif0: saif@80042000 { + #sound-dai-cells = <0>; + compatible = "fsl,imx28-saif"; + reg = <0x80042000 0x2000>; + interrupts = <59>; + #clock-cells = <0>; + clocks = <&clks 53>; + dmas = <&dma_apbx 4>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + power: power@80044000 { + reg = <0x80044000 0x2000>; + status = "disabled"; + }; + + saif1: saif@80046000 { + #sound-dai-cells = <0>; + compatible = "fsl,imx28-saif"; + reg = <0x80046000 0x2000>; + interrupts = <58>; + clocks = <&clks 54>; + dmas = <&dma_apbx 5>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + lradc: lradc@80050000 { + compatible = "fsl,imx28-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <10 14 15 16 17 18 19 + 20 21 22 23 24 25>; + status = "disabled"; + clocks = <&clks 41>; + #io-channel-cells = <1>; + }; + + spdif: spdif@80054000 { + reg = <0x80054000 0x2000>; + interrupts = <45>; + dmas = <&dma_apbx 2>; + dma-names = "tx"; + status = "disabled"; + }; + + mxs_rtc: rtc@80056000 { + compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc"; + reg = <0x80056000 0x2000>; + interrupts = <29>; + }; + + i2c0: i2c@80058000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-i2c"; + reg = <0x80058000 0x2000>; + interrupts = <111>; + clock-frequency = <100000>; + dmas = <&dma_apbx 6>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + i2c1: i2c@8005a000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-i2c"; + reg = <0x8005a000 0x2000>; + interrupts = <110>; + clock-frequency = <100000>; + dmas = <&dma_apbx 7>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + pwm: pwm@80064000 { + compatible = "fsl,imx28-pwm", "fsl,imx23-pwm"; + reg = <0x80064000 0x2000>; + clocks = <&clks 44>; + #pwm-cells = <2>; + fsl,pwm-number = <8>; + status = "disabled"; + }; + + timer: timrot@80068000 { + compatible = "fsl,imx28-timrot", "fsl,timrot"; + reg = <0x80068000 0x2000>; + interrupts = <48 49 50 51>; + clocks = <&clks 26>; + }; + + auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112>; + dmas = <&dma_apbx 8>, <&dma_apbx 9>; + dma-names = "rx", "tx"; + clocks = <&clks 45>; + status = "disabled"; + }; + + auart1: serial@8006c000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006c000 0x2000>; + interrupts = <113>; + dmas = <&dma_apbx 10>, <&dma_apbx 11>; + dma-names = "rx", "tx"; + clocks = <&clks 45>; + status = "disabled"; + }; + + auart2: serial@8006e000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006e000 0x2000>; + interrupts = <114>; + dmas = <&dma_apbx 12>, <&dma_apbx 13>; + dma-names = "rx", "tx"; + clocks = <&clks 45>; + status = "disabled"; + }; + + auart3: serial@80070000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x80070000 0x2000>; + interrupts = <115>; + dmas = <&dma_apbx 14>, <&dma_apbx 15>; + dma-names = "rx", "tx"; + clocks = <&clks 45>; + status = "disabled"; + }; + + auart4: serial@80072000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x80072000 0x2000>; + interrupts = <116>; + dmas = <&dma_apbx 0>, <&dma_apbx 1>; + dma-names = "rx", "tx"; + clocks = <&clks 45>; + status = "disabled"; + }; + + duart: serial@80074000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80074000 0x1000>; + interrupts = <47>; + clocks = <&clks 45>, <&clks 26>; + clock-names = "uart", "apb_pclk"; + status = "disabled"; + }; + + usbphy0: usbphy@8007c000 { + compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy"; + reg = <0x8007c000 0x2000>; + clocks = <&clks 62>; + status = "disabled"; + }; + + usbphy1: usbphy@8007e000 { + compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy"; + reg = <0x8007e000 0x2000>; + clocks = <&clks 63>; + status = "disabled"; + }; + }; + }; + + ahb@80080000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x80080000 0x80000>; + ranges; + + usb0: usb@80080000 { + compatible = "fsl,imx28-usb", "fsl,imx27-usb"; + reg = <0x80080000 0x10000>; + interrupts = <93>; + clocks = <&clks 60>; + fsl,usbphy = <&usbphy0>; + status = "disabled"; + }; + + usb1: usb@80090000 { + compatible = "fsl,imx28-usb", "fsl,imx27-usb"; + reg = <0x80090000 0x10000>; + interrupts = <92>; + clocks = <&clks 61>; + fsl,usbphy = <&usbphy1>; + dr_mode = "host"; + status = "disabled"; + }; + + dflpt: dflpt@800c0000 { + reg = <0x800c0000 0x10000>; + status = "disabled"; + }; + + mac0: ethernet@800f0000 { + compatible = "fsl,imx28-fec"; + reg = <0x800f0000 0x4000>; + interrupts = <101>; + clocks = <&clks 57>, <&clks 57>, <&clks 64>; + clock-names = "ipg", "ahb", "enet_out"; + status = "disabled"; + }; + + mac1: ethernet@800f4000 { + compatible = "fsl,imx28-fec"; + reg = <0x800f4000 0x4000>; + interrupts = <102>; + clocks = <&clks 57>, <&clks 57>; + clock-names = "ipg", "ahb"; + status = "disabled"; + }; + + etn_switch: switch@800f8000 { + reg = <0x800f8000 0x8000>; + status = "disabled"; + }; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&lradc 8>; + }; +}; diff --git a/arch/arm/dts/mxs-pinfunc.h b/arch/arm/dts/mxs-pinfunc.h new file mode 100644 index 0000000000..c6da987b20 --- /dev/null +++ b/arch/arm/dts/mxs-pinfunc.h @@ -0,0 +1,31 @@ +/* + * Header providing constants for i.MX28 pinctrl bindings. + * + * Copyright (C) 2013 Lothar Waßmann LW@KARO-electronics.de + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DT_BINDINGS_MXS_PINCTRL_H__ +#define __DT_BINDINGS_MXS_PINCTRL_H__ + +/* fsl,drive-strength property */ +#define MXS_DRIVE_4mA 0 +#define MXS_DRIVE_8mA 1 +#define MXS_DRIVE_12mA 2 +#define MXS_DRIVE_16mA 3 + +/* fsl,voltage property */ +#define MXS_VOLTAGE_LOW 0 +#define MXS_VOLTAGE_HIGH 1 + +/* fsl,pull-up property */ +#define MXS_PULL_DISABLE 0 +#define MXS_PULL_ENABLE 1 + +#endif /* __DT_BINDINGS_MXS_PINCTRL_H__ */
The fec_mxc.c driver can be reused by i.MX28 when DM_ETH is enabled. One only needs to add proper compatible and dependency on FEC_MXC in the Kconfig.
Signed-off-by: Lukasz Majewski lukma@denx.de ---
drivers/net/Kconfig | 2 +- drivers/net/fec_mxc.c | 1 + 2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index e6a4fdf30e..04f886fe86 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -190,7 +190,7 @@ config FEC_MXC_MDIO_BASE
config FEC_MXC bool "FEC Ethernet controller" - depends on MX5 || MX6 || MX7 || IMX8 || VF610 + depends on MX5 || MX6 || MX7 || IMX8 || VF610 || MX28 help This driver supports the 10/100 Fast Ethernet controller for NXP i.MX processors. diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c index a672250e16..394585cc63 100644 --- a/drivers/net/fec_mxc.c +++ b/drivers/net/fec_mxc.c @@ -1492,6 +1492,7 @@ static const struct udevice_id fecmxc_ids[] = { { .compatible = "fsl,imx53-fec" }, { .compatible = "fsl,imx7d-fec" }, { .compatible = "fsl,mvf600-fec" }, + { .compatible = "fsl,imx28-fec" }, { } };
This commit adds support for DM in the mxs_gpio.c driver when DM_GPIO is enabled in Kconfig.
Signed-off-by: Lukasz Majewski lukma@denx.de ---
arch/arm/include/asm/arch-mxs/gpio.h | 28 +++++++ drivers/gpio/mxs_gpio.c | 149 +++++++++++++++++++++++++++++++++++ 2 files changed, 177 insertions(+)
diff --git a/arch/arm/include/asm/arch-mxs/gpio.h b/arch/arm/include/asm/arch-mxs/gpio.h index 34fa421945..0c152e25e2 100644 --- a/arch/arm/include/asm/arch-mxs/gpio.h +++ b/arch/arm/include/asm/arch-mxs/gpio.h @@ -15,4 +15,32 @@ void mxs_gpio_init(void); inline void mxs_gpio_init(void) {} #endif
+#if defined(CONFIG_MX28) && CONFIG_IS_ENABLED(DM_GPIO) +/* + * According to i.MX28 Reference Manual: + * 'i.MX28 Applications Processor Reference Manual, Rev. 1, 2010' + * The i.MX28 has following number of GPIOs available: + * Bank 0: 0-28 -> 29 PINS + * Bank 1: 0-31 -> 32 PINS + * Bank 2: 0-27 -> 28 PINS + * Bank 3: 0-30 -> 31 PINS + * Bank 4: 0-20 -> 21 PINS + */ +#define IMX28_GPIO_BANK0_PIN_NR 29 +#define IMX28_GPIO_BANK1_PIN_NR 32 +#define IMX28_GPIO_BANK2_PIN_NR 28 +#define IMX28_GPIO_BANK3_PIN_NR 31 +#define IMX28_GPIO_BANK4_PIN_NR 21 +#define IMX28_GPIO_BANK_NR 5 + +struct mxs_gpio_platdata { + u32 gpio_nr_of_bank_pins[IMX28_GPIO_BANK_NR]; + u32 gpio_base_nr[IMX28_GPIO_BANK_NR]; + u32 ngpio; +}; + +extern const struct mxs_gpio_platdata mxs_gpio_def; +#define IMX_GPIO_NR(port, index) (mxs_gpio_def.gpio_base_nr[(port)] + (index)) +#endif + #endif /* __MX28_GPIO_H__ */ diff --git a/drivers/gpio/mxs_gpio.c b/drivers/gpio/mxs_gpio.c index c2c8a25886..0ad29a7342 100644 --- a/drivers/gpio/mxs_gpio.c +++ b/drivers/gpio/mxs_gpio.c @@ -51,6 +51,7 @@ void mxs_gpio_init(void) } }
+#ifndef CONFIG_DM_GPIO int gpio_get_value(unsigned gpio) { uint32_t bank = PAD_BANK(gpio); @@ -127,3 +128,151 @@ int name_to_gpio(const char *name)
return (bank << MXS_PAD_BANK_SHIFT) | (pin << MXS_PAD_PIN_SHIFT); } +#else /* CONFIG_DM_GPIO */ +#include <dm.h> +#include <asm/gpio.h> +#include <asm/arch/gpio.h> +#ifdef CONFIG_MX28 +const struct mxs_gpio_platdata mxs_gpio_def = { + .gpio_nr_of_bank_pins[0] = IMX28_GPIO_BANK0_PIN_NR, + .gpio_nr_of_bank_pins[1] = IMX28_GPIO_BANK1_PIN_NR, + .gpio_nr_of_bank_pins[2] = IMX28_GPIO_BANK2_PIN_NR, + .gpio_nr_of_bank_pins[3] = IMX28_GPIO_BANK3_PIN_NR, + .gpio_nr_of_bank_pins[4] = IMX28_GPIO_BANK4_PIN_NR, + .gpio_base_nr[0] = 0, + .gpio_base_nr[1] = IMX28_GPIO_BANK0_PIN_NR, + .gpio_base_nr[2] = (IMX28_GPIO_BANK0_PIN_NR + \ + IMX28_GPIO_BANK1_PIN_NR), + .gpio_base_nr[3] = (IMX28_GPIO_BANK0_PIN_NR + \ + IMX28_GPIO_BANK1_PIN_NR + \ + IMX28_GPIO_BANK2_PIN_NR), + .gpio_base_nr[4] = (IMX28_GPIO_BANK0_PIN_NR + \ + IMX28_GPIO_BANK1_PIN_NR + \ + IMX28_GPIO_BANK2_PIN_NR + \ + IMX28_GPIO_BANK3_PIN_NR), + .ngpio = (IMX28_GPIO_BANK0_PIN_NR + \ + IMX28_GPIO_BANK1_PIN_NR + \ + IMX28_GPIO_BANK2_PIN_NR + \ + IMX28_GPIO_BANK3_PIN_NR + \ + IMX28_GPIO_BANK4_PIN_NR), +}; + +#else +#error "Only i.MX28 supported with DM_GPIO" +#endif + +struct mxs_gpio_priv { + unsigned int bank; +}; + +static int mxs_gpio_get_value(struct udevice *dev, unsigned offset) +{ + struct mxs_gpio_priv *priv = dev_get_priv(dev); + struct mxs_register_32 *reg = + (struct mxs_register_32 *)(MXS_PINCTRL_BASE + + PINCTRL_DIN(priv->bank)); + + return (readl(®->reg) >> offset) & 1; +} + +static int mxs_gpio_set_value(struct udevice *dev, unsigned offset, + int value) +{ + struct mxs_gpio_priv *priv = dev_get_priv(dev); + struct mxs_register_32 *reg = + (struct mxs_register_32 *)(MXS_PINCTRL_BASE + + PINCTRL_DOUT(priv->bank)); + if (value) + writel(1 << offset, ®->reg_set); + else + writel(1 << offset, ®->reg_clr); + + return 0; +} + +static int mxs_gpio_direction_input(struct udevice *dev, unsigned offset) +{ + struct mxs_gpio_priv *priv = dev_get_priv(dev); + struct mxs_register_32 *reg = + (struct mxs_register_32 *)(MXS_PINCTRL_BASE + + PINCTRL_DOE(priv->bank)); + + writel(1 << offset, ®->reg_clr); + + return 0; +} + +static int mxs_gpio_direction_output(struct udevice *dev, unsigned offset, + int value) +{ + struct mxs_gpio_priv *priv = dev_get_priv(dev); + struct mxs_register_32 *reg = + (struct mxs_register_32 *)(MXS_PINCTRL_BASE + + PINCTRL_DOE(priv->bank)); + + mxs_gpio_set_value(dev, offset, value); + + writel(1 << offset, ®->reg_set); + + return 0; +} + +static int mxs_gpio_get_function(struct udevice *dev, unsigned offset) +{ + struct mxs_gpio_priv *priv = dev_get_priv(dev); + struct mxs_register_32 *reg = + (struct mxs_register_32 *)(MXS_PINCTRL_BASE + + PINCTRL_DOE(priv->bank)); + bool is_output = !!(readl(®->reg) >> offset); + + return is_output ? GPIOF_OUTPUT : GPIOF_INPUT; +} + +static const struct dm_gpio_ops gpio_mxs_ops = { + .direction_input = mxs_gpio_direction_input, + .direction_output = mxs_gpio_direction_output, + .get_value = mxs_gpio_get_value, + .set_value = mxs_gpio_set_value, + .get_function = mxs_gpio_get_function, +}; + +static int mxs_gpio_probe(struct udevice *dev) +{ + struct mxs_gpio_priv *priv = dev_get_priv(dev); + struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev); + struct mxs_gpio_platdata *pdata = + (struct mxs_gpio_platdata *)dev_get_driver_data(dev); + char name[18], *str; + int ret; + + ret = dev_read_u32(dev, "reg", &priv->bank); + if (ret) { + printf("%s: No 'reg' property defined!\n", __func__); + return ret; + } + + sprintf(name, "GPIO%d_", priv->bank); + str = strdup(name); + if (!str) + return -ENOMEM; + + uc_priv->bank_name = str; + uc_priv->gpio_count = pdata->gpio_nr_of_bank_pins[priv->bank]; + + return 0; +} + +static const struct udevice_id mxs_gpio_ids[] = { + { .compatible = "fsl,imx28-gpio", .data = (ulong)&mxs_gpio_def }, + { } +}; + +U_BOOT_DRIVER(gpio_mxs) = { + .name = "gpio_mxs", + .id = UCLASS_GPIO, + .ops = &gpio_mxs_ops, + .probe = mxs_gpio_probe, + .priv_auto_alloc_size = sizeof(struct mxs_gpio_priv), + .of_match = mxs_gpio_ids, +}; +#endif
The code responsible for setting proper values in the MUX registers (in the mxs_pinctrl_set_state()) has been ported from Barebox project (branch: master, SHA1: eb3b0f7414cd8102844dd16b1c789e445e8947f8, file: drivers/pinctrl/pinctrl-mxs.c).
As the pinctrl node in the imx28.dtsi file has gpio pins nodes as subnodes, it was necessary to use 'dm_scan_fdt_dev()' (as a .bind method) to also make them 'visible' by the DM's "gpio_mxs" driver.
Signed-off-by: Lukasz Majewski lukma@denx.de ---
drivers/pinctrl/nxp/Kconfig | 10 +++ drivers/pinctrl/nxp/Makefile | 1 + drivers/pinctrl/nxp/pinctrl-mxs.c | 164 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 175 insertions(+) create mode 100644 drivers/pinctrl/nxp/pinctrl-mxs.c
diff --git a/drivers/pinctrl/nxp/Kconfig b/drivers/pinctrl/nxp/Kconfig index 61f93be42d..f2e67ca231 100644 --- a/drivers/pinctrl/nxp/Kconfig +++ b/drivers/pinctrl/nxp/Kconfig @@ -89,6 +89,16 @@ config PINCTRL_IMX8M only parses the 'fsl,pins' property and configure related registers.
+config PINCTRL_MXS + bool "NXP MXS pinctrl driver" + depends on ARCH_MX28 && PINCTRL_FULL + help + Say Y here to enable the i.MX mxs pinctrl driver + + This option provides a simple pinctrl driver for i.MX mxs SoC + familiy, e.g. i.MX28. This feature depends on device tree + configuration. + config PINCTRL_VYBRID bool "Vybrid (vf610) pinctrl driver" depends on ARCH_VF610 && PINCTRL_FULL diff --git a/drivers/pinctrl/nxp/Makefile b/drivers/pinctrl/nxp/Makefile index b340d9448a..b86448aac9 100644 --- a/drivers/pinctrl/nxp/Makefile +++ b/drivers/pinctrl/nxp/Makefile @@ -6,4 +6,5 @@ obj-$(CONFIG_PINCTRL_IMX7ULP) += pinctrl-imx7ulp.o obj-$(CONFIG_PINCTRL_IMX_SCU) += pinctrl-scu.o obj-$(CONFIG_PINCTRL_IMX8) += pinctrl-imx8.o obj-$(CONFIG_PINCTRL_IMX8M) += pinctrl-imx8m.o +obj-$(CONFIG_PINCTRL_MXS) += pinctrl-mxs.o obj-$(CONFIG_PINCTRL_VYBRID) += pinctrl-vf610.o diff --git a/drivers/pinctrl/nxp/pinctrl-mxs.c b/drivers/pinctrl/nxp/pinctrl-mxs.c new file mode 100644 index 0000000000..42b1b7998b --- /dev/null +++ b/drivers/pinctrl/nxp/pinctrl-mxs.c @@ -0,0 +1,164 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2019 DENX Software Engineering + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de + * + * This work is based on drivers/pinctrl/pinctrl-mxs.c + * SHA1: eb3b0f7414cd8102844dd16b1c789e445e8947f8 + * from Barebox project. + * + * Author of original Barebox pinctrl-mxs.c: + * Copyright (c) 2015 Sascha Hauer s.hauer@pengutronix.de + */ + +#include <common.h> +#include <linux/io.h> +#include <linux/err.h> +#include <dm.h> +#include <dm/pinctrl.h> +#include <dm/read.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define PINID(bank, pin) ((bank) * 32 + (pin)) +#define MUXID_TO_PINID(m) PINID((m) >> 12 & 0xf, (m) >> 4 & 0xff) +#define MUXID_TO_MUXSEL(m) ((m) & 0xf) +#define PINID_TO_BANK(p) ((p) >> 5) +#define PINID_TO_PIN(p) ((p) % 32) + +#define STMP_OFFSET_REG_SET 0x4 +#define STMP_OFFSET_REG_CLR 0x8 +#define STMP_OFFSET_REG_TOG 0xc + +struct mxs_pinctrl_priv { + void __iomem *base; +}; + +static int mxs_pinctrl_set_state(struct udevice *dev, struct udevice *config) +{ + int ma_present = 0, vol_present = 0, pull_present = 0; + struct mxs_pinctrl_priv *iomux = dev_get_priv(dev); + u32 *pin_data, val, ma, vol, pull; + int npins, size, i, ret; + + debug("\n%s: set state: %s\n", __func__, config->name); + + size = dev_read_size(config, "fsl,pinmux-ids"); + if (size < 0) + return size; + + if (!size || size % 4) { + dev_err(dev, "Invalid fsl,pinmux-ids property in %s\n", + config->name); + return -EINVAL; + } + + npins = size / 4; + + pin_data = devm_kzalloc(dev, size, 0); + if (!pin_data) + return -ENOMEM; + + ret = dev_read_u32_array(config, "fsl,pinmux-ids", pin_data, npins); + if (ret) { + dev_err(dev, "Error reading pin data.\n"); + devm_kfree(dev, pin_data); + return -EINVAL; + } + + ret = dev_read_u32(config, "fsl,drive-strength", &ma); + if (!ret) + ma_present = 1; + + ret = dev_read_u32(config, "fsl,voltage", &vol); + if (!ret) + vol_present = 1; + + ret = dev_read_u32(config, "fsl,pull-up", &pull); + if (!ret) + pull_present = 1; + + for (i = 0; i < npins; i++) { + int muxsel, pinid, bank, pin, shift; + void __iomem *reg; + + val = *pin_data++; + + muxsel = MUXID_TO_MUXSEL(val); + pinid = MUXID_TO_PINID(val); + + bank = PINID_TO_BANK(pinid); + pin = PINID_TO_PIN(pinid); + reg = iomux->base + 0x100; + reg += bank * 0x20 + pin / 16 * 0x10; + shift = pin % 16 * 2; + + writel(0x3 << shift, reg + STMP_OFFSET_REG_CLR); + writel(muxsel << shift, reg + STMP_OFFSET_REG_SET); + + debug("(val: 0x%x) pin %d, mux %d, ma: %d, vol: %d, pull: %d\n", + val, pinid, muxsel, ma, vol, pull); + + /* drive */ + reg = iomux->base + 0x300; + reg += bank * 0x40 + pin / 8 * 0x10; + + /* mA */ + if (ma_present) { + shift = pin % 8 * 4; + writel(0x3 << shift, reg + STMP_OFFSET_REG_CLR); + writel(ma << shift, reg + STMP_OFFSET_REG_SET); + } + + /* vol */ + if (vol_present) { + shift = pin % 8 * 4 + 2; + if (vol) + writel(1 << shift, reg + STMP_OFFSET_REG_SET); + else + writel(1 << shift, reg + STMP_OFFSET_REG_CLR); + } + + /* pull */ + if (pull_present) { + reg = iomux->base + 0x600; + reg += bank * 0x10; + shift = pin; + if (pull) + writel(1 << shift, reg + STMP_OFFSET_REG_SET); + else + writel(1 << shift, reg + STMP_OFFSET_REG_CLR); + } + } + + return 0; +} + +static struct pinctrl_ops mxs_pinctrl_ops = { + .set_state = mxs_pinctrl_set_state, +}; + +static int mxs_pinctrl_probe(struct udevice *dev) +{ + struct mxs_pinctrl_priv *iomux = dev_get_priv(dev); + iomux->base = dev_read_addr_ptr(dev); + + return 0; +} + +static const struct udevice_id mxs_pinctrl_match[] = { + { .compatible = "fsl,imx28-pinctrl" }, + { /* sentinel */ } +}; + +U_BOOT_DRIVER(mxs_pinctrl) = { + .name = "mxs-pinctrl", + .id = UCLASS_PINCTRL, + .of_match = of_match_ptr(mxs_pinctrl_match), + .probe = mxs_pinctrl_probe, +#if !CONFIG_IS_ENABLED(OF_PLATDATA) + .bind = dm_scan_fdt_dev, +#endif + .priv_auto_alloc_size = sizeof(struct mxs_pinctrl_priv), + .ops = &mxs_pinctrl_ops, +};
participants (1)
-
Lukasz Majewski