[U-Boot] [PATCH 1/2] arm64: zynqmp: Add support for m-a2197-02
It is based on m-a2197-01 with some changes in i2c intrastructure.
Signed-off-by: Michal Simek michal.simek@xilinx.com ---
arch/arm/dts/Makefile | 1 + arch/arm/dts/zynqmp-m-a2197-02-revA.dts | 465 ++++++++++++++++++ configs/xilinx_zynqmp_a2197_revA_defconfig | 2 +- .../xilinx_zynqmp_m_a2197_02_revA_defconfig | 117 +++++ 4 files changed, 584 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/zynqmp-m-a2197-02-revA.dts create mode 100644 configs/xilinx_zynqmp_m_a2197_02_revA_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index a9240ef450f3..05110a1755e7 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -250,6 +250,7 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \ zynqmp-a2197-revA.dtb \ zynqmp-g-a2197-00-revA.dtb \ zynqmp-m-a2197-01-revA.dtb \ + zynqmp-m-a2197-02-revA.dtb \ zynqmp-p-a2197-00-revA.dtb \ zynqmp-mini.dtb \ zynqmp-mini-emmc0.dtb \ diff --git a/arch/arm/dts/zynqmp-m-a2197-02-revA.dts b/arch/arm/dts/zynqmp-m-a2197-02-revA.dts new file mode 100644 index 000000000000..0a95a272c87f --- /dev/null +++ b/arch/arm/dts/zynqmp-m-a2197-02-revA.dts @@ -0,0 +1,465 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * dts file for Xilinx Versal a2197 RevA System Controller + * + * (C) Copyright 2019, Xilinx, Inc. + * + * Michal Simek michal.simek@xilinx.com + */ +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Versal System Controller on a2197 Memory Char board RevA"; + compatible = "xlnx,zynqmp-m-a2197-02-revA", "xlnx,zynqmp-a2197-revA", + "xlnx,zynqmp-a2197", "xlnx,zynqmp"; + + aliases { + ethernet0 = &gem0; + gpio0 = &gpio; + i2c0 = &i2c0; + i2c1 = &i2c1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + rtc0 = &rtc; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &dcc; + usb0 = &usb0; + usb1 = &usb1; + spi0 = &qspi; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial0:115200n8"; + xlnx,eeprom = <&eeprom>; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; /* FIXME don't know how big memory is there */ + }; +}; + +&qspi { + status = "okay"; + is-dual = <1>; + flash@0 { + compatible = "m25p80", "spi-flash"; /* 32MB */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + }; +}; + +&sdhci0 { /* emmc MIO 13-23 - with some settings 16GB */ + status = "okay"; + non-removable; + disable-wp; + bus-width = <8>; + xlnx,mio_bank = <0>; /* FIXME tap delay */ +}; + +&uart0 { /* uart0 MIO38-39 */ + status = "okay"; + u-boot,dm-pre-reloc; +}; + +&uart1 { /* uart1 MIO40-41 */ + status = "okay"; + u-boot,dm-pre-reloc; +}; + +&sdhci1 { /* sd1 MIO45-51 cd in place */ + status = "disable"; + no-1-8-v; + disable-wp; + xlnx,mio_bank = <1>; +}; + +&gem0 { + status = "okay"; + phy-handle = <&phy0>; + phy-mode = "sgmii"; + phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; + phy0: phy@0 { /* marwell m88e1512 - SGMII */ + reg = <0>; + }; +}; + +&gpio { + status = "okay"; + gpio-line-names = "SCLK_OUT", "MISO_MO1", "MO2", "MO3", "MOSI_MIO0", /* 0 - 4 */ + "N_SS_OUT", "", "SYS_CTRL0", "SYS_CTRL1", "SYS_CTRL2", /* 5 - 9 */ + "SYS_CTRL3", "SYS_CTRL4", "SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */ + "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */ + "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */ + "", "RXD0_IN", "TXD0_OUT", "TXD1_OUT", "RXD1_IN", /* 25 - 29 */ + "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */ + "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */ + "UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */ + "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */ + "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */ + "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */ + "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */ + "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */ + "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */ + "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */ + "", "", "", "", "", /* 78 - 79 */ + "", "", "", "", "", /* 80 - 84 */ + "", "", "", "", "", /* 85 -89 */ + "", "", "", "", "", /* 90 - 94 */ + "", "", "", "", "", /* 95 - 99 */ + "", "", "", "", "", /* 100 - 104 */ + "", "", "", "", "", /* 105 - 109 */ + "", "", "", "", "", /* 110 - 114 */ + "", "", "", "", "", /* 115 - 119 */ + "", "", "", "", "", /* 120 - 124 */ + "", "", "", "", "", /* 125 - 129 */ + "", "", "", "", "", /* 130 - 134 */ + "", "", "", "", "", /* 135 - 139 */ + "", "", "", "", "", /* 140 - 144 */ + "", "", "", "", "", /* 145 - 149 */ + "", "", "", "", "", /* 150 - 154 */ + "", "", "", "", "", /* 155 - 159 */ + "", "", "", "", "", /* 160 - 164 */ + "", "", "", "", "", /* 165 - 169 */ + "", "", "", ""; /* 170 - 174 */ +}; + +&i2c0 { /* MIO 34-35 - can't stay here */ + status = "okay"; + clock-frequency = <400000>; + i2c-mux@74 { /* u46 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + /* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */ + i2c@0 { /* PMBUS must be enabled via SW21 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + reg_vcc1v2_lp4: tps544@15 { /* u97 */ + compatible = "ti,tps544b25"; + reg = <0x15>; + }; + reg_vcc1v1_lp4: tps544@16 { /* u95 */ + compatible = "ti,tps544b25"; + reg = <0x16>; + }; + reg_vdd1_1v8_lp4: tps544@17 { /* u99 */ + compatible = "ti,tps544b25"; + reg = <0x17>; + }; + /* UTIL_PMBUS connection */ + reg_vcc1v8: tps544@13 { /* u92 */ + compatible = "ti,tps544b25"; + reg = <0x13>; + }; + reg_vcc3v3: tps544@14 { /* u93 */ + compatible = "ti,tps544b25"; + reg = <0x14>; + }; + reg_vcc5v0: tps544@1e { /* u94 */ + compatible = "ti,tps544b25"; + reg = <0x1e>; + }; + reg_vpp_2v5_ddr4: tps544@1x { /* u3007 */ + compatible = "ti,tps544b25"; + reg = <0x17>; /* FIXME wrong in schematics */ + }; + }; + i2c@1 { /* PMBUS_INA226 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + vcc_aux: ina226@42 { /* u86 */ + compatible = "ti,ina226"; + reg = <0x42>; + shunt-resistor = <5000>; + }; + vcc_ram: ina226@43 { /* u81 */ + compatible = "ti,ina226"; + reg = <0x43>; + shunt-resistor = <5000>; + }; + vcc1v1_lp4: ina226@46 { /* u96 */ + compatible = "ti,ina226"; + reg = <0x46>; + shunt-resistor = <5000>; + }; + vcc1v2_lp4: ina226@47 { /* u98 */ + compatible = "ti,ina226"; + reg = <0x47>; + shunt-resistor = <5000>; + }; + vdd1_1v8_lp4: ina226@48 { /* u100 */ + compatible = "ti,ina226"; + reg = <0x48>; + shunt-resistor = <5000>; + }; + }; + i2c@2 { /* PMBUS1 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + reg_vccint: tps53681@c0 { /* u69 */ + compatible = "ti,tps53681"; /* FIXME no linux driver */ + reg = <0xc0>; + }; + reg_vcc_pmc: tps544@7 { /* u80 */ + compatible = "ti,tps544b25"; + reg = <0x7>; + }; + reg_vcc_ram: tps544@8 { /* u82 */ + compatible = "ti,tps544b25"; + reg = <0x8>; + }; + reg_vcc_pslp: tps544@9 { /* u83 */ + compatible = "ti,tps544b25"; + reg = <0x9>; + }; + reg_vcc_psfp: tps544@a { /* u84 */ + compatible = "ti,tps544b25"; + reg = <0xa>; + }; + reg_vccaux: tps544@d { /* u85 */ + compatible = "ti,tps544b25"; + reg = <0xd>; + }; + reg_vccaux_pmc: tps544@e { /* u87 */ + compatible = "ti,tps544b25"; + reg = <0xe>; + }; + reg_vcco_500: tps544@f { /* u88 */ + compatible = "ti,tps544b25"; + reg = <0xf>; + }; + reg_vcco_501: tps544@10 { /* u89 */ + compatible = "ti,tps544b25"; + reg = <0x10>; + }; + reg_vcco_502: tps544@11 { /* u90 */ + compatible = "ti,tps544b25"; + reg = <0x11>; + }; + reg_vcco_503: tps544@12 { /* u91 */ + compatible = "ti,tps544b25"; + reg = <0x12>; + }; + }; + i2c@3 { /* MEM PMBUS - FIXME bug in schematics */ + #address-cells = <1>; + #size-cells = <0>; + /* reg = <3>; */ + }; + i2c@4 { /* LP_I2C_SM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + /* connected to U20G */ + }; + i2c@5 { /* C0_DDR4_RDIMM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + }; + i2c@6 { /* C2_DDR5_RDIMM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + }; + i2c@7 { /* C3_DDR4_UDIMM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + }; + }; +}; + +/* TODO sysctrl via J239 */ +/* TODO samtec J212G/H via J242 */ +/* TODO teensy via U30 PCA9543A bus 1 */ +&i2c1 { /* i2c1 MIO 36-37 */ + status = "okay"; + clock-frequency = <400000>; + + /* Must be enabled via J242 */ + eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */ + compatible = "atmel,24c02"; + reg = <0x51>; + }; + + i2c-mux@74 { /* u47 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + /* FIXME reset connected to SYSCTRL_IIC_MUX1_RESET */ + dc_i2c: i2c@0 { /* DC_I2C */ + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + /* Use for storing information about SC board */ + eeprom: eeprom@54 { /* u51 - m24128 16kB FIXME addr */ + compatible = "atmel,24c08"; + reg = <0x54>; + }; + si570_ref_clk: clock-generator@5d { /* u26 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x5d>; /* FIXME addr */ + temperature-stability = <50>; + factory-fout = <156250000>; /* FIXME every chip can be different */ + clock-frequency = <33333333>; + clock-output-names = "REF_CLK"; /* FIXME */ + }; + /* Connection via Samtec U20D */ + /* Use for storing information about X-PRC card */ + x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */ + compatible = "atmel,24c02"; + reg = <0x52>; + }; + + /* Use for setting up certain features on X-PRC card */ + x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */ + compatible = "nxp,pca9534"; + reg = <0x22>; + gpio-controller; /* IRQ not connected */ + #gpio-cells = <2>; + gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4", + "", "", "", ""; + gtr_sel0 { + gpio-hog; + gpios = <0 0>; + input; /* FIXME add meaning */ + line-name = "sw4_1"; + }; + gtr_sel1 { + gpio-hog; + gpios = <1 0>; + input; /* FIXME add meaning */ + line-name = "sw4_2"; + }; + gtr_sel2 { + gpio-hog; + gpios = <2 0>; + input; /* FIXME add meaning */ + line-name = "sw4_3"; + }; + gtr_sel3 { + gpio-hog; + gpios = <3 0>; + input; /* FIXME add meaning */ + line-name = "sw4_4"; + }; + }; + }; + i2c@2 { /* C0_DDR4 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + si570_c0_ddr4: clock-generator@55 { /* u4 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C0_DD4_SI570_CLK"; + }; + }; + i2c@3 { /* C1_RLD3 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + si570_c1_lp4: clock-generator@55 { /* u7 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C1_RLD3_SI570_CLK"; + }; + }; + i2c@4 { /* C2_DDR5 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + si570_c2_lp4: clock-generator@55 { /* u10 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C2_DDR5_SI570_CLK"; + }; + }; + i2c@5 { /* C3_DDR4 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + si570_c3_lp4: clock-generator@55 { /* u15 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C3_LP4_SI570_CLK"; + }; + }; + i2c@6 { /* HSDP_SI570 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + si570_hsdp: clock-generator@5d { /* u19 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x5d>; + temperature-stability = <50>; + factory-fout = <156250000>; + clock-frequency = <156250000>; + clock-output-names = "HSDP_SI570"; + }; + }; + }; +}; + +&usb0 { + status = "okay"; + xlnx,usb-polarity = <0>; + xlnx,usb-reset-mode = <0>; +}; + +&dwc3_0 { + status = "okay"; + dr_mode = "host"; + /* dr_mode = "peripheral"; */ + maximum-speed = "high-speed"; +}; + +&usb1 { + status = "disabled"; /* not at mem board */ + xlnx,usb-polarity = <0>; + xlnx,usb-reset-mode = <0>; +}; + +&dwc3_1 { + /delete-property/ phy-names ; + /delete-property/ phys ; + maximum-speed = "high-speed"; + snps,dis_u2_susphy_quirk ; + snps,dis_u3_susphy_quirk ; + status = "disabled"; +}; diff --git a/configs/xilinx_zynqmp_a2197_revA_defconfig b/configs/xilinx_zynqmp_a2197_revA_defconfig index 5acf70107339..b928d50da123 100644 --- a/configs/xilinx_zynqmp_a2197_revA_defconfig +++ b/configs/xilinx_zynqmp_a2197_revA_defconfig @@ -43,7 +43,7 @@ CONFIG_CMD_TIMER=y CONFIG_CMD_EXT4_WRITE=y CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="zynqmp-a2197-revA" -CONFIG_OF_LIST="zynqmp-a2197-revA zynqmp-g-a2197-00-revA zynqmp-p-a2197-00-revA zynqmp-m-a2197-01-revA" +CONFIG_OF_LIST="zynqmp-a2197-revA zynqmp-g-a2197-00-revA zynqmp-p-a2197-00-revA zynqmp-m-a2197-01-revA zynqmp-m-a2197-02-revA" CONFIG_ENV_IS_IN_FAT=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SPL_DM=y diff --git a/configs/xilinx_zynqmp_m_a2197_02_revA_defconfig b/configs/xilinx_zynqmp_m_a2197_02_revA_defconfig new file mode 100644 index 000000000000..cf8f97ceca0a --- /dev/null +++ b/configs/xilinx_zynqmp_m_a2197_02_revA_defconfig @@ -0,0 +1,117 @@ +CONFIG_ARM=y +CONFIG_ARCH_ZYNQMP=y +CONFIG_SYS_TEXT_BASE=0x8000000 +CONFIG_SYS_MALLOC_F_LEN=0x8000 +CONFIG_SPL=y +CONFIG_DEBUG_UART_BASE=0xff000000 +CONFIG_DEBUG_UART_CLOCK=100000000 +CONFIG_IDENT_STRING=" Xilinx ZynqMP SC for Versal" +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y +CONFIG_ZYNQMP_USB=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_LOAD_FIT=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_RAM_SUPPORT=y +CONFIG_SPL_RAM_DEVICE=y +CONFIG_SPL_ATF=y +CONFIG_SYS_PROMPT="ZynqMP> " +CONFIG_CMD_THOR_DOWNLOAD=y +CONFIG_CMD_MEMTEST=y +CONFIG_SYS_ALT_MEMTEST=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_FPGA_LOADBP=y +CONFIG_CMD_FPGA_LOADP=y +CONFIG_CMD_FPGA_LOAD_SECURE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SDRAM=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_TIME=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="zynqmp-m-a2197-02-revA" +CONFIG_ENV_IS_IN_FAT=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SCSI_AHCI=y +CONFIG_SATA_CEVA=y +CONFIG_CLK_ZYNQMP=y +CONFIG_DFU_RAM=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_FPGA_XILINX=y +CONFIG_FPGA_ZYNQMPPL=y +CONFIG_DM_GPIO=y +CONFIG_XILINX_GPIO=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_CADENCE=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x0 +CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW=0x0 +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_ZYNQ=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SF_DUAL_FLASH=y +CONFIG_SPI_GENERIC=y +CONFIG_SPI_FLASH_ISSI=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHY_MARVELL=y +CONFIG_PHY_NATSEMI=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_TI=y +CONFIG_PHY_VITESSE=y +CONFIG_PHY_FIXED=y +CONFIG_PHY_GIGE=y +CONFIG_MII=y +CONFIG_ZYNQ_GEM=y +CONFIG_SCSI=y +CONFIG_DM_SCSI=y +CONFIG_DEBUG_UART_ZYNQ=y +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_ZYNQ_SERIAL=y +CONFIG_SPI=y +CONFIG_ZYNQMP_GQSPI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_XHCI_ZYNQMP=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GADGET=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_ULPI_VIEWPORT=y +CONFIG_USB_ULPI=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Xilinx" +CONFIG_USB_GADGET_VENDOR_NUM=0x03FD +CONFIG_USB_GADGET_PRODUCT_NUM=0x0300 +CONFIG_USB_FUNCTION_THOR=y +CONFIG_SPL_GZIP=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
It is based on m-a2197-01 with some changes in i2c intrastructure.
Signed-off-by: Michal Simek michal.simek@xilinx.com ---
arch/arm/dts/Makefile | 1 + arch/arm/dts/zynqmp-m-a2197-03-revA.dts | 455 ++++++++++++++++++ configs/xilinx_zynqmp_a2197_revA_defconfig | 2 +- .../xilinx_zynqmp_m_a2197_03_revA_defconfig | 117 +++++ 4 files changed, 574 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/zynqmp-m-a2197-03-revA.dts create mode 100644 configs/xilinx_zynqmp_m_a2197_03_revA_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 05110a1755e7..f37d20c38f66 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -251,6 +251,7 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \ zynqmp-g-a2197-00-revA.dtb \ zynqmp-m-a2197-01-revA.dtb \ zynqmp-m-a2197-02-revA.dtb \ + zynqmp-m-a2197-03-revA.dtb \ zynqmp-p-a2197-00-revA.dtb \ zynqmp-mini.dtb \ zynqmp-mini-emmc0.dtb \ diff --git a/arch/arm/dts/zynqmp-m-a2197-03-revA.dts b/arch/arm/dts/zynqmp-m-a2197-03-revA.dts new file mode 100644 index 000000000000..d8fc730325cb --- /dev/null +++ b/arch/arm/dts/zynqmp-m-a2197-03-revA.dts @@ -0,0 +1,455 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * dts file for Xilinx Versal a2197 RevA System Controller + * + * (C) Copyright 2019, Xilinx, Inc. + * + * Michal Simek michal.simek@xilinx.com + */ +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Versal System Controller on a2197 Memory Char board RevA"; + compatible = "xlnx,zynqmp-m-a2197-03-revA", "xlnx,zynqmp-a2197-revA", + "xlnx,zynqmp-a2197", "xlnx,zynqmp"; + + aliases { + ethernet0 = &gem0; + gpio0 = &gpio; + i2c0 = &i2c0; + i2c1 = &i2c1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + rtc0 = &rtc; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &dcc; + usb0 = &usb0; + usb1 = &usb1; + spi0 = &qspi; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial0:115200n8"; + xlnx,eeprom = <&eeprom>; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; /* FIXME don't know how big memory is there */ + }; +}; + +&qspi { + status = "okay"; + is-dual = <1>; + flash@0 { + compatible = "m25p80", "spi-flash"; /* 32MB */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + }; +}; + +&sdhci0 { /* emmc MIO 13-23 - with some settings 16GB */ + status = "okay"; + non-removable; + disable-wp; + bus-width = <8>; + xlnx,mio_bank = <0>; /* FIXME tap delay */ +}; + +&uart0 { /* uart0 MIO38-39 */ + status = "okay"; + u-boot,dm-pre-reloc; +}; + +&uart1 { /* uart1 MIO40-41 */ + status = "okay"; + u-boot,dm-pre-reloc; +}; + +&sdhci1 { /* sd1 MIO45-51 cd in place */ + status = "disable"; + no-1-8-v; + disable-wp; + xlnx,mio_bank = <1>; +}; + +&gem0 { + status = "okay"; + phy-handle = <&phy0>; + phy-mode = "sgmii"; + phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; + phy0: phy@0 { /* marwell m88e1512 - SGMII */ + reg = <0>; + }; +}; + +&gpio { + status = "okay"; + gpio-line-names = "SCLK_OUT", "MISO_MO1", "MO2", "MO3", "MOSI_MIO0", /* 0 - 4 */ + "N_SS_OUT", "", "SYS_CTRL0", "SYS_CTRL1", "SYS_CTRL2", /* 5 - 9 */ + "SYS_CTRL3", "SYS_CTRL4", "SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */ + "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */ + "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */ + "", "RXD0_IN", "TXD0_OUT", "TXD1_OUT", "RXD1_IN", /* 25 - 29 */ + "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */ + "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */ + "UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */ + "SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */ + "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */ + "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */ + "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */ + "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */ + "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */ + "USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */ + "", "", "", "", "", /* 78 - 79 */ + "", "", "", "", "", /* 80 - 84 */ + "", "", "", "", "", /* 85 -89 */ + "", "", "", "", "", /* 90 - 94 */ + "", "", "", "", "", /* 95 - 99 */ + "", "", "", "", "", /* 100 - 104 */ + "", "", "", "", "", /* 105 - 109 */ + "", "", "", "", "", /* 110 - 114 */ + "", "", "", "", "", /* 115 - 119 */ + "", "", "", "", "", /* 120 - 124 */ + "", "", "", "", "", /* 125 - 129 */ + "", "", "", "", "", /* 130 - 134 */ + "", "", "", "", "", /* 135 - 139 */ + "", "", "", "", "", /* 140 - 144 */ + "", "", "", "", "", /* 145 - 149 */ + "", "", "", "", "", /* 150 - 154 */ + "", "", "", "", "", /* 155 - 159 */ + "", "", "", "", "", /* 160 - 164 */ + "", "", "", "", "", /* 165 - 169 */ + "", "", "", ""; /* 170 - 174 */ +}; + +&i2c0 { /* MIO 34-35 - can't stay here */ + status = "okay"; + clock-frequency = <400000>; + i2c-mux@74 { /* u46 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + /* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */ + i2c@0 { /* PMBUS must be enabled via SW21 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + reg_vcc1v2_lp4: tps544@15 { /* u97 */ + compatible = "ti,tps544b25"; + reg = <0x15>; + }; + reg_vcc1v1_lp4: tps544@16 { /* u95 */ + compatible = "ti,tps544b25"; + reg = <0x16>; + }; + reg_vdd1_1v8_lp4: tps544@17 { /* u99 */ + compatible = "ti,tps544b25"; + reg = <0x17>; + }; + /* UTIL_PMBUS connection */ + reg_vcc1v8: tps544@13 { /* u92 */ + compatible = "ti,tps544b25"; + reg = <0x13>; + }; + reg_vcc3v3: tps544@14 { /* u93 */ + compatible = "ti,tps544b25"; + reg = <0x14>; + }; + reg_vcc5v0: tps544@1e { /* u94 */ + compatible = "ti,tps544b25"; + reg = <0x1e>; + }; + reg_vpp_2v5_ddr4: tps544@1x { /* u3007 */ + compatible = "ti,tps544b25"; + reg = <0x17>; /* FIXME wrong in schematics */ + }; + }; + i2c@1 { /* PMBUS_INA226 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + vcc_aux: ina226@42 { /* u86 */ + compatible = "ti,ina226"; + reg = <0x42>; + shunt-resistor = <5000>; + }; + vcc_ram: ina226@43 { /* u81 */ + compatible = "ti,ina226"; + reg = <0x43>; + shunt-resistor = <5000>; + }; + vcc1v1_lp4: ina226@46 { /* u96 */ + compatible = "ti,ina226"; + reg = <0x46>; + shunt-resistor = <5000>; + }; + vcc1v2_lp4: ina226@47 { /* u98 */ + compatible = "ti,ina226"; + reg = <0x47>; + shunt-resistor = <5000>; + }; + vdd1_1v8_lp4: ina226@48 { /* u100 */ + compatible = "ti,ina226"; + reg = <0x48>; + shunt-resistor = <5000>; + }; + }; + i2c@2 { /* PMBUS1 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + reg_vccint: tps53681@c0 { /* u69 */ + compatible = "ti,tps53681"; /* FIXME no linux driver */ + reg = <0xc0>; + }; + reg_vcc_pmc: tps544@7 { /* u80 */ + compatible = "ti,tps544b25"; + reg = <0x7>; + }; + reg_vcc_ram: tps544@8 { /* u82 */ + compatible = "ti,tps544b25"; + reg = <0x8>; + }; + reg_vcc_pslp: tps544@9 { /* u83 */ + compatible = "ti,tps544b25"; + reg = <0x9>; + }; + reg_vcc_psfp: tps544@a { /* u84 */ + compatible = "ti,tps544b25"; + reg = <0xa>; + }; + reg_vccaux: tps544@d { /* u85 */ + compatible = "ti,tps544b25"; + reg = <0xd>; + }; + reg_vccaux_pmc: tps544@e { /* u87 */ + compatible = "ti,tps544b25"; + reg = <0xe>; + }; + reg_vcco_500: tps544@f { /* u88 */ + compatible = "ti,tps544b25"; + reg = <0xf>; + }; + reg_vcco_501: tps544@10 { /* u89 */ + compatible = "ti,tps544b25"; + reg = <0x10>; + }; + reg_vcco_502: tps544@11 { /* u90 */ + compatible = "ti,tps544b25"; + reg = <0x11>; + }; + reg_vcco_503: tps544@12 { /* u91 */ + compatible = "ti,tps544b25"; + reg = <0x12>; + }; + }; + i2c@3 { /* MEM PMBUS - FIXME bug in schematics */ + #address-cells = <1>; + #size-cells = <0>; + /* reg = <3>; */ + }; + i2c@4 { /* LP_I2C_SM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + /* connected to U20G */ + }; + i2c@5 { /* DDR4_SODIMM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + }; + }; +}; + +/* TODO sysctrl via J239 */ +/* TODO samtec J212G/H via J242 */ +/* TODO teensy via U30 PCA9543A bus 1 */ +&i2c1 { /* i2c1 MIO 36-37 */ + status = "okay"; + clock-frequency = <400000>; + + /* Must be enabled via J242 */ + eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */ + compatible = "atmel,24c02"; + reg = <0x51>; + }; + + i2c-mux@74 { /* u47 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + /* FIXME reset connected to SYSCTRL_IIC_MUX1_RESET */ + dc_i2c: i2c@0 { /* DC_I2C */ + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + /* Use for storing information about SC board */ + eeprom: eeprom@54 { /* u51 - m24128 16kB FIXME addr */ + compatible = "atmel,24c08"; + reg = <0x54>; + }; + si570_ref_clk: clock-generator@5d { /* u26 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x5d>; /* FIXME addr */ + temperature-stability = <50>; + factory-fout = <156250000>; /* FIXME every chip can be different */ + clock-frequency = <33333333>; + clock-output-names = "REF_CLK"; /* FIXME */ + }; + /* Connection via Samtec U20D */ + /* Use for storing information about X-PRC card */ + x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */ + compatible = "atmel,24c02"; + reg = <0x52>; + }; + + /* Use for setting up certain features on X-PRC card */ + x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */ + compatible = "nxp,pca9534"; + reg = <0x22>; + gpio-controller; /* IRQ not connected */ + #gpio-cells = <2>; + gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4", + "", "", "", ""; + gtr_sel0 { + gpio-hog; + gpios = <0 0>; + input; /* FIXME add meaning */ + line-name = "sw4_1"; + }; + gtr_sel1 { + gpio-hog; + gpios = <1 0>; + input; /* FIXME add meaning */ + line-name = "sw4_2"; + }; + gtr_sel2 { + gpio-hog; + gpios = <2 0>; + input; /* FIXME add meaning */ + line-name = "sw4_3"; + }; + gtr_sel3 { + gpio-hog; + gpios = <3 0>; + input; /* FIXME add meaning */ + line-name = "sw4_4"; + }; + }; + }; + i2c@2 { /* C0_DDR4 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + si570_c0_ddr4: clock-generator@55 { /* u4 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C0_DD4_SI570_CLK"; + }; + }; + i2c@3 { /* C1_SODIMM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + si570_c1_lp4: clock-generator@55 { /* u7 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C1_SODIMM_SI570_CLK"; + }; + }; + i2c@4 { /* C2_QDRIV */ + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + si570_c2_lp4: clock-generator@55 { /* u10 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C2_QDRIV_SI570_CLK"; + }; + }; + i2c@5 { /* C3_DDR4 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + si570_c3_lp4: clock-generator@55 { /* u15 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x55>; + temperature-stability = <50>; + factory-fout = <30000000>; + clock-frequency = <30000000>; + clock-output-names = "C3_LP4_SI570_CLK"; + }; + }; + i2c@6 { /* HSDP_SI570 */ + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + si570_hsdp: clock-generator@5d { /* u19 */ + #clock-cells = <0>; + compatible = "silabs,si570"; + reg = <0x5d>; + temperature-stability = <50>; + factory-fout = <156250000>; + clock-frequency = <156250000>; + clock-output-names = "HSDP_SI570"; + }; + }; + }; +}; + +&usb0 { + status = "okay"; + xlnx,usb-polarity = <0>; + xlnx,usb-reset-mode = <0>; +}; + +&dwc3_0 { + status = "okay"; + dr_mode = "host"; + /* dr_mode = "peripheral"; */ + maximum-speed = "high-speed"; +}; + +&usb1 { + status = "disabled"; /* not at mem board */ + xlnx,usb-polarity = <0>; + xlnx,usb-reset-mode = <0>; +}; + +&dwc3_1 { + /delete-property/ phy-names ; + /delete-property/ phys ; + maximum-speed = "high-speed"; + snps,dis_u2_susphy_quirk ; + snps,dis_u3_susphy_quirk ; + status = "disabled"; +}; diff --git a/configs/xilinx_zynqmp_a2197_revA_defconfig b/configs/xilinx_zynqmp_a2197_revA_defconfig index b928d50da123..e5e2b54ae3b1 100644 --- a/configs/xilinx_zynqmp_a2197_revA_defconfig +++ b/configs/xilinx_zynqmp_a2197_revA_defconfig @@ -43,7 +43,7 @@ CONFIG_CMD_TIMER=y CONFIG_CMD_EXT4_WRITE=y CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="zynqmp-a2197-revA" -CONFIG_OF_LIST="zynqmp-a2197-revA zynqmp-g-a2197-00-revA zynqmp-p-a2197-00-revA zynqmp-m-a2197-01-revA zynqmp-m-a2197-02-revA" +CONFIG_OF_LIST="zynqmp-a2197-revA zynqmp-g-a2197-00-revA zynqmp-p-a2197-00-revA zynqmp-m-a2197-01-revA zynqmp-m-a2197-02-revA zynqmp-m-a2197-03-revA" CONFIG_ENV_IS_IN_FAT=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SPL_DM=y diff --git a/configs/xilinx_zynqmp_m_a2197_03_revA_defconfig b/configs/xilinx_zynqmp_m_a2197_03_revA_defconfig new file mode 100644 index 000000000000..6fd40fd44e59 --- /dev/null +++ b/configs/xilinx_zynqmp_m_a2197_03_revA_defconfig @@ -0,0 +1,117 @@ +CONFIG_ARM=y +CONFIG_ARCH_ZYNQMP=y +CONFIG_SYS_TEXT_BASE=0x8000000 +CONFIG_SYS_MALLOC_F_LEN=0x8000 +CONFIG_SPL=y +CONFIG_DEBUG_UART_BASE=0xff000000 +CONFIG_DEBUG_UART_CLOCK=100000000 +CONFIG_IDENT_STRING=" Xilinx ZynqMP SC for Versal" +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y +CONFIG_ZYNQMP_USB=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_LOAD_FIT=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_RAM_SUPPORT=y +CONFIG_SPL_RAM_DEVICE=y +CONFIG_SPL_ATF=y +CONFIG_SYS_PROMPT="ZynqMP> " +CONFIG_CMD_THOR_DOWNLOAD=y +CONFIG_CMD_MEMTEST=y +CONFIG_SYS_ALT_MEMTEST=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_FPGA_LOADBP=y +CONFIG_CMD_FPGA_LOADP=y +CONFIG_CMD_FPGA_LOAD_SECURE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SDRAM=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_TIME=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="zynqmp-m-a2197-03-revA" +CONFIG_ENV_IS_IN_FAT=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SCSI_AHCI=y +CONFIG_SATA_CEVA=y +CONFIG_CLK_ZYNQMP=y +CONFIG_DFU_RAM=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_FPGA_XILINX=y +CONFIG_FPGA_ZYNQMPPL=y +CONFIG_DM_GPIO=y +CONFIG_XILINX_GPIO=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_CADENCE=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x0 +CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW=0x0 +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_ZYNQ=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SF_DUAL_FLASH=y +CONFIG_SPI_GENERIC=y +CONFIG_SPI_FLASH_ISSI=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHY_MARVELL=y +CONFIG_PHY_NATSEMI=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_TI=y +CONFIG_PHY_VITESSE=y +CONFIG_PHY_FIXED=y +CONFIG_PHY_GIGE=y +CONFIG_MII=y +CONFIG_ZYNQ_GEM=y +CONFIG_SCSI=y +CONFIG_DM_SCSI=y +CONFIG_DEBUG_UART_ZYNQ=y +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_ZYNQ_SERIAL=y +CONFIG_SPI=y +CONFIG_ZYNQMP_GQSPI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_XHCI_ZYNQMP=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GADGET=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_ULPI_VIEWPORT=y +CONFIG_USB_ULPI=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Xilinx" +CONFIG_USB_GADGET_VENDOR_NUM=0x03FD +CONFIG_USB_GADGET_PRODUCT_NUM=0x0300 +CONFIG_USB_FUNCTION_THOR=y +CONFIG_SPL_GZIP=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
út 15. 10. 2019 v 10:55 odesílatel Michal Simek michal.simek@xilinx.com napsal:
It is based on m-a2197-01 with some changes in i2c intrastructure.
Signed-off-by: Michal Simek michal.simek@xilinx.com
arch/arm/dts/Makefile | 1 + arch/arm/dts/zynqmp-m-a2197-03-revA.dts | 455 ++++++++++++++++++ configs/xilinx_zynqmp_a2197_revA_defconfig | 2 +- .../xilinx_zynqmp_m_a2197_03_revA_defconfig | 117 +++++ 4 files changed, 574 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/zynqmp-m-a2197-03-revA.dts create mode 100644 configs/xilinx_zynqmp_m_a2197_03_revA_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 05110a1755e7..f37d20c38f66 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -251,6 +251,7 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \ zynqmp-g-a2197-00-revA.dtb \ zynqmp-m-a2197-01-revA.dtb \ zynqmp-m-a2197-02-revA.dtb \
zynqmp-m-a2197-03-revA.dtb \ zynqmp-p-a2197-00-revA.dtb \ zynqmp-mini.dtb \ zynqmp-mini-emmc0.dtb \diff --git a/arch/arm/dts/zynqmp-m-a2197-03-revA.dts b/arch/arm/dts/zynqmp-m-a2197-03-revA.dts new file mode 100644 index 000000000000..d8fc730325cb --- /dev/null +++ b/arch/arm/dts/zynqmp-m-a2197-03-revA.dts @@ -0,0 +1,455 @@ +// SPDX-License-Identifier: GPL-2.0 +/*
- dts file for Xilinx Versal a2197 RevA System Controller
- (C) Copyright 2019, Xilinx, Inc.
- Michal Simek michal.simek@xilinx.com
- */
+/dts-v1/;
+#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/gpio/gpio.h>
+/ {
model = "Versal System Controller on a2197 Memory Char board RevA";compatible = "xlnx,zynqmp-m-a2197-03-revA", "xlnx,zynqmp-a2197-revA","xlnx,zynqmp-a2197", "xlnx,zynqmp";aliases {ethernet0 = &gem0;gpio0 = &gpio;i2c0 = &i2c0;i2c1 = &i2c1;mmc0 = &sdhci0;mmc1 = &sdhci1;rtc0 = &rtc;serial0 = &uart0;serial1 = &uart1;serial2 = &dcc;usb0 = &usb0;usb1 = &usb1;spi0 = &qspi;};chosen {bootargs = "earlycon";stdout-path = "serial0:115200n8";xlnx,eeprom = <&eeprom>;};memory@0 {device_type = "memory";reg = <0x0 0x0 0x0 0x80000000>; /* FIXME don't know how big memory is there */};+};
+&qspi {
status = "okay";is-dual = <1>;flash@0 {compatible = "m25p80", "spi-flash"; /* 32MB */#address-cells = <1>;#size-cells = <1>;reg = <0x0>;spi-tx-bus-width = <1>;spi-rx-bus-width = <4>;spi-max-frequency = <108000000>;};+};
+&sdhci0 { /* emmc MIO 13-23 - with some settings 16GB */
status = "okay";non-removable;disable-wp;bus-width = <8>;xlnx,mio_bank = <0>; /* FIXME tap delay */+};
+&uart0 { /* uart0 MIO38-39 */
status = "okay";u-boot,dm-pre-reloc;+};
+&uart1 { /* uart1 MIO40-41 */
status = "okay";u-boot,dm-pre-reloc;+};
+&sdhci1 { /* sd1 MIO45-51 cd in place */
status = "disable";no-1-8-v;disable-wp;xlnx,mio_bank = <1>;+};
+&gem0 {
status = "okay";phy-handle = <&phy0>;phy-mode = "sgmii";phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>;phy0: phy@0 { /* marwell m88e1512 - SGMII */reg = <0>;};+};
+&gpio {
status = "okay";gpio-line-names = "SCLK_OUT", "MISO_MO1", "MO2", "MO3", "MOSI_MIO0", /* 0 - 4 */"N_SS_OUT", "", "SYS_CTRL0", "SYS_CTRL1", "SYS_CTRL2", /* 5 - 9 */"SYS_CTRL3", "SYS_CTRL4", "SYS_CTRL5", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */"EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */"EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */"", "RXD0_IN", "TXD0_OUT", "TXD1_OUT", "RXD1_IN", /* 25 - 29 */"", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */"LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */"UART1_TXD_OUT", "UART1_RXD_IN", "ETH_RESET_B", "", "", /* 40 - 44 */"SD1_CD_B", "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3", /* 45 - 49 */"SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */"USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */"USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", /* 60 - 64 */"USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", /* 65 - 69 */"USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", /* 70 - 74 */"USB1_DATA7", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */"", "", "", "", "", /* 78 - 79 */"", "", "", "", "", /* 80 - 84 */"", "", "", "", "", /* 85 -89 */"", "", "", "", "", /* 90 - 94 */"", "", "", "", "", /* 95 - 99 */"", "", "", "", "", /* 100 - 104 */"", "", "", "", "", /* 105 - 109 */"", "", "", "", "", /* 110 - 114 */"", "", "", "", "", /* 115 - 119 */"", "", "", "", "", /* 120 - 124 */"", "", "", "", "", /* 125 - 129 */"", "", "", "", "", /* 130 - 134 */"", "", "", "", "", /* 135 - 139 */"", "", "", "", "", /* 140 - 144 */"", "", "", "", "", /* 145 - 149 */"", "", "", "", "", /* 150 - 154 */"", "", "", "", "", /* 155 - 159 */"", "", "", "", "", /* 160 - 164 */"", "", "", "", "", /* 165 - 169 */"", "", "", ""; /* 170 - 174 */+};
+&i2c0 { /* MIO 34-35 - can't stay here */
status = "okay";clock-frequency = <400000>;i2c-mux@74 { /* u46 */compatible = "nxp,pca9548";#address-cells = <1>;#size-cells = <0>;reg = <0x74>;/* FIXME reset connected to SYSCTRL_IIC_MUX0_RESET */i2c@0 { /* PMBUS must be enabled via SW21 */#address-cells = <1>;#size-cells = <0>;reg = <0>;reg_vcc1v2_lp4: tps544@15 { /* u97 */compatible = "ti,tps544b25";reg = <0x15>;};reg_vcc1v1_lp4: tps544@16 { /* u95 */compatible = "ti,tps544b25";reg = <0x16>;};reg_vdd1_1v8_lp4: tps544@17 { /* u99 */compatible = "ti,tps544b25";reg = <0x17>;};/* UTIL_PMBUS connection */reg_vcc1v8: tps544@13 { /* u92 */compatible = "ti,tps544b25";reg = <0x13>;};reg_vcc3v3: tps544@14 { /* u93 */compatible = "ti,tps544b25";reg = <0x14>;};reg_vcc5v0: tps544@1e { /* u94 */compatible = "ti,tps544b25";reg = <0x1e>;};reg_vpp_2v5_ddr4: tps544@1x { /* u3007 */compatible = "ti,tps544b25";reg = <0x17>; /* FIXME wrong in schematics */};};i2c@1 { /* PMBUS_INA226 */#address-cells = <1>;#size-cells = <0>;reg = <1>;vcc_aux: ina226@42 { /* u86 */compatible = "ti,ina226";reg = <0x42>;shunt-resistor = <5000>;};vcc_ram: ina226@43 { /* u81 */compatible = "ti,ina226";reg = <0x43>;shunt-resistor = <5000>;};vcc1v1_lp4: ina226@46 { /* u96 */compatible = "ti,ina226";reg = <0x46>;shunt-resistor = <5000>;};vcc1v2_lp4: ina226@47 { /* u98 */compatible = "ti,ina226";reg = <0x47>;shunt-resistor = <5000>;};vdd1_1v8_lp4: ina226@48 { /* u100 */compatible = "ti,ina226";reg = <0x48>;shunt-resistor = <5000>;};};i2c@2 { /* PMBUS1 */#address-cells = <1>;#size-cells = <0>;reg = <2>;reg_vccint: tps53681@c0 { /* u69 */compatible = "ti,tps53681"; /* FIXME no linux driver */reg = <0xc0>;};reg_vcc_pmc: tps544@7 { /* u80 */compatible = "ti,tps544b25";reg = <0x7>;};reg_vcc_ram: tps544@8 { /* u82 */compatible = "ti,tps544b25";reg = <0x8>;};reg_vcc_pslp: tps544@9 { /* u83 */compatible = "ti,tps544b25";reg = <0x9>;};reg_vcc_psfp: tps544@a { /* u84 */compatible = "ti,tps544b25";reg = <0xa>;};reg_vccaux: tps544@d { /* u85 */compatible = "ti,tps544b25";reg = <0xd>;};reg_vccaux_pmc: tps544@e { /* u87 */compatible = "ti,tps544b25";reg = <0xe>;};reg_vcco_500: tps544@f { /* u88 */compatible = "ti,tps544b25";reg = <0xf>;};reg_vcco_501: tps544@10 { /* u89 */compatible = "ti,tps544b25";reg = <0x10>;};reg_vcco_502: tps544@11 { /* u90 */compatible = "ti,tps544b25";reg = <0x11>;};reg_vcco_503: tps544@12 { /* u91 */compatible = "ti,tps544b25";reg = <0x12>;};};i2c@3 { /* MEM PMBUS - FIXME bug in schematics */#address-cells = <1>;#size-cells = <0>;/* reg = <3>; */};i2c@4 { /* LP_I2C_SM */#address-cells = <1>;#size-cells = <0>;reg = <4>;/* connected to U20G */};i2c@5 { /* DDR4_SODIMM */#address-cells = <1>;#size-cells = <0>;reg = <5>;};};+};
+/* TODO sysctrl via J239 */ +/* TODO samtec J212G/H via J242 */ +/* TODO teensy via U30 PCA9543A bus 1 */ +&i2c1 { /* i2c1 MIO 36-37 */
status = "okay";clock-frequency = <400000>;/* Must be enabled via J242 */eeprom_versal: eeprom@51 { /* x-prc-01-revA u116, x-prc-02-revA u12 */compatible = "atmel,24c02";reg = <0x51>;};i2c-mux@74 { /* u47 */compatible = "nxp,pca9548";#address-cells = <1>;#size-cells = <0>;reg = <0x74>;/* FIXME reset connected to SYSCTRL_IIC_MUX1_RESET */dc_i2c: i2c@0 { /* DC_I2C */#address-cells = <1>;#size-cells = <0>;reg = <0>;/* Use for storing information about SC board */eeprom: eeprom@54 { /* u51 - m24128 16kB FIXME addr */compatible = "atmel,24c08";reg = <0x54>;};si570_ref_clk: clock-generator@5d { /* u26 */#clock-cells = <0>;compatible = "silabs,si570";reg = <0x5d>; /* FIXME addr */temperature-stability = <50>;factory-fout = <156250000>; /* FIXME every chip can be different */clock-frequency = <33333333>;clock-output-names = "REF_CLK"; /* FIXME */};/* Connection via Samtec U20D *//* Use for storing information about X-PRC card */x_prc_eeprom: eeprom@52 { /* x-prc-01-revA u120, x-prc-02-revA u16 */compatible = "atmel,24c02";reg = <0x52>;};/* Use for setting up certain features on X-PRC card */x_prc_tca9534: gpio@22 { /* x-prc-01-revA u121, x-prc-02-revA u17 */compatible = "nxp,pca9534";reg = <0x22>;gpio-controller; /* IRQ not connected */#gpio-cells = <2>;gpio-line-names = "sw4_1", "sw4_2", "sw4_3", "sw4_4","", "", "", "";gtr_sel0 {gpio-hog;gpios = <0 0>;input; /* FIXME add meaning */line-name = "sw4_1";};gtr_sel1 {gpio-hog;gpios = <1 0>;input; /* FIXME add meaning */line-name = "sw4_2";};gtr_sel2 {gpio-hog;gpios = <2 0>;input; /* FIXME add meaning */line-name = "sw4_3";};gtr_sel3 {gpio-hog;gpios = <3 0>;input; /* FIXME add meaning */line-name = "sw4_4";};};};i2c@2 { /* C0_DDR4 */#address-cells = <1>;#size-cells = <0>;reg = <2>;si570_c0_ddr4: clock-generator@55 { /* u4 */#clock-cells = <0>;compatible = "silabs,si570";reg = <0x55>;temperature-stability = <50>;factory-fout = <30000000>;clock-frequency = <30000000>;clock-output-names = "C0_DD4_SI570_CLK";};};i2c@3 { /* C1_SODIMM */#address-cells = <1>;#size-cells = <0>;reg = <3>;si570_c1_lp4: clock-generator@55 { /* u7 */#clock-cells = <0>;compatible = "silabs,si570";reg = <0x55>;temperature-stability = <50>;factory-fout = <30000000>;clock-frequency = <30000000>;clock-output-names = "C1_SODIMM_SI570_CLK";};};i2c@4 { /* C2_QDRIV */#address-cells = <1>;#size-cells = <0>;reg = <4>;si570_c2_lp4: clock-generator@55 { /* u10 */#clock-cells = <0>;compatible = "silabs,si570";reg = <0x55>;temperature-stability = <50>;factory-fout = <30000000>;clock-frequency = <30000000>;clock-output-names = "C2_QDRIV_SI570_CLK";};};i2c@5 { /* C3_DDR4 */#address-cells = <1>;#size-cells = <0>;reg = <5>;si570_c3_lp4: clock-generator@55 { /* u15 */#clock-cells = <0>;compatible = "silabs,si570";reg = <0x55>;temperature-stability = <50>;factory-fout = <30000000>;clock-frequency = <30000000>;clock-output-names = "C3_LP4_SI570_CLK";};};i2c@6 { /* HSDP_SI570 */#address-cells = <1>;#size-cells = <0>;reg = <6>;si570_hsdp: clock-generator@5d { /* u19 */#clock-cells = <0>;compatible = "silabs,si570";reg = <0x5d>;temperature-stability = <50>;factory-fout = <156250000>;clock-frequency = <156250000>;clock-output-names = "HSDP_SI570";};};};+};
+&usb0 {
status = "okay";xlnx,usb-polarity = <0>;xlnx,usb-reset-mode = <0>;+};
+&dwc3_0 {
status = "okay";dr_mode = "host";/* dr_mode = "peripheral"; */maximum-speed = "high-speed";+};
+&usb1 {
status = "disabled"; /* not at mem board */xlnx,usb-polarity = <0>;xlnx,usb-reset-mode = <0>;+};
+&dwc3_1 {
/delete-property/ phy-names ;/delete-property/ phys ;maximum-speed = "high-speed";snps,dis_u2_susphy_quirk ;snps,dis_u3_susphy_quirk ;status = "disabled";+}; diff --git a/configs/xilinx_zynqmp_a2197_revA_defconfig b/configs/xilinx_zynqmp_a2197_revA_defconfig index b928d50da123..e5e2b54ae3b1 100644 --- a/configs/xilinx_zynqmp_a2197_revA_defconfig +++ b/configs/xilinx_zynqmp_a2197_revA_defconfig @@ -43,7 +43,7 @@ CONFIG_CMD_TIMER=y CONFIG_CMD_EXT4_WRITE=y CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="zynqmp-a2197-revA" -CONFIG_OF_LIST="zynqmp-a2197-revA zynqmp-g-a2197-00-revA zynqmp-p-a2197-00-revA zynqmp-m-a2197-01-revA zynqmp-m-a2197-02-revA" +CONFIG_OF_LIST="zynqmp-a2197-revA zynqmp-g-a2197-00-revA zynqmp-p-a2197-00-revA zynqmp-m-a2197-01-revA zynqmp-m-a2197-02-revA zynqmp-m-a2197-03-revA" CONFIG_ENV_IS_IN_FAT=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SPL_DM=y diff --git a/configs/xilinx_zynqmp_m_a2197_03_revA_defconfig b/configs/xilinx_zynqmp_m_a2197_03_revA_defconfig new file mode 100644 index 000000000000..6fd40fd44e59 --- /dev/null +++ b/configs/xilinx_zynqmp_m_a2197_03_revA_defconfig @@ -0,0 +1,117 @@ +CONFIG_ARM=y +CONFIG_ARCH_ZYNQMP=y +CONFIG_SYS_TEXT_BASE=0x8000000 +CONFIG_SYS_MALLOC_F_LEN=0x8000 +CONFIG_SPL=y +CONFIG_DEBUG_UART_BASE=0xff000000 +CONFIG_DEBUG_UART_CLOCK=100000000 +CONFIG_IDENT_STRING=" Xilinx ZynqMP SC for Versal" +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y +CONFIG_ZYNQMP_USB=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_LOAD_FIT=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_RAM_SUPPORT=y +CONFIG_SPL_RAM_DEVICE=y +CONFIG_SPL_ATF=y +CONFIG_SYS_PROMPT="ZynqMP> " +CONFIG_CMD_THOR_DOWNLOAD=y +CONFIG_CMD_MEMTEST=y +CONFIG_SYS_ALT_MEMTEST=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_FPGA_LOADBP=y +CONFIG_CMD_FPGA_LOADP=y +CONFIG_CMD_FPGA_LOAD_SECURE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SDRAM=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_TIME=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="zynqmp-m-a2197-03-revA" +CONFIG_ENV_IS_IN_FAT=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SCSI_AHCI=y +CONFIG_SATA_CEVA=y +CONFIG_CLK_ZYNQMP=y +CONFIG_DFU_RAM=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_FPGA_XILINX=y +CONFIG_FPGA_ZYNQMPPL=y +CONFIG_DM_GPIO=y +CONFIG_XILINX_GPIO=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_CADENCE=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x0 +CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW=0x0 +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_ZYNQ=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SF_DUAL_FLASH=y +CONFIG_SPI_GENERIC=y +CONFIG_SPI_FLASH_ISSI=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHY_MARVELL=y +CONFIG_PHY_NATSEMI=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_TI=y +CONFIG_PHY_VITESSE=y +CONFIG_PHY_FIXED=y +CONFIG_PHY_GIGE=y +CONFIG_MII=y +CONFIG_ZYNQ_GEM=y +CONFIG_SCSI=y +CONFIG_DM_SCSI=y +CONFIG_DEBUG_UART_ZYNQ=y +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_ZYNQ_SERIAL=y +CONFIG_SPI=y +CONFIG_ZYNQMP_GQSPI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_XHCI_ZYNQMP=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GADGET=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_ULPI_VIEWPORT=y +CONFIG_USB_ULPI=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Xilinx" +CONFIG_USB_GADGET_VENDOR_NUM=0x03FD +CONFIG_USB_GADGET_PRODUCT_NUM=0x0300 +CONFIG_USB_FUNCTION_THOR=y +CONFIG_SPL_GZIP=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
2.17.1
Applied both but with removing PROMPT and spi generic symbols from defconfigs and also with iio ina226 description which is done for 00/01 variants.
M
participants (2)
-
Michal Simek -
Michal Simek