[U-Boot] [PATCH V1 0/5] prepare for mx6dl/ mx6solo

Troy Kisky

23 Oct 23 Oct

10:57 p.m.

New subject: [U-Boot] [PATCH V1 1/5] mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololite

Previously, the same value was returned for both mx6dl and mx6solo. Check number of processors to differeniate. Also, a freescale patch says that sololite has its cpu/rev stored at 0x280 instead of 0x260. I don't have a sololite to verify.

Signed-off-by: Troy Kisky troy.kisky@boundarydevices.com

--- --- arch/arm/cpu/armv7/mx6/soc.c | 32 +++++++++++++++++++++-------- arch/arm/imx-common/cpu.c | 16 ++++++++------- arch/arm/include/asm/arch-mx5/sys_proto.h | 9 +++++++- arch/arm/include/asm/arch-mx6/imx-regs.h | 2 ++ arch/arm/include/asm/arch-mx6/sys_proto.h | 9 +++++++- 5 files changed, 51 insertions(+), 17 deletions(-)

diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index bc65767..a8aad5d 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -31,17 +31,33 @@ #include <asm/arch/sys_proto.h> #include <asm/imx-common/boot_mode.h>

+struct scu_regs { + u32 ctrl; + u32 config; + u32 status; + u32 invalidate; + u32 fpga_rev; +}; + u32 get_cpu_rev(void) { struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; - int reg = readl(&anatop->digprog); - - /* Read mx6 variant: quad, dual or solo */ - int system_rev = (reg >> 4) & 0xFF000; - /* Read mx6 silicon revision */ - system_rev |= (reg & 0xFF) + 0x10; - - return system_rev; + u32 reg = readl(&anatop->digprog_sololite); + u32 type = ((reg >> 16) & 0xff); + + if (type != MXC_CPU_MX6SL) { + reg = readl(&anatop->digprog); + type = ((reg >> 16) & 0xff); + if (type == MXC_CPU_MX6DL) { + struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; + u32 cfg = readl(&scu->config) & 3; + + if (!cfg) + type = MXC_CPU_MX6SOLO; + } + } + reg &= 0xff; /* mx6 silicon revision */ + return (type << 12) | (reg + 0x10); }

void init_aips(void) diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c index a10d12d..102c254 100644 --- a/arch/arm/imx-common/cpu.c +++ b/arch/arm/imx-common/cpu.c @@ -67,18 +67,20 @@ char *get_reset_cause(void)

#if defined(CONFIG_DISPLAY_CPUINFO)

-static const char *get_imx_type(u32 imxtype) +const char *get_imx_type(u32 imxtype) { switch (imxtype) { - case 0x63: + case MXC_CPU_MX6Q: return "6Q"; /* Quad-core version of the mx6 */ - case 0x61: - return "6DS"; /* Dual/Solo version of the mx6 */ - case 0x60: + case MXC_CPU_MX6DL: + return "6DL"; /* Dual Lite version of the mx6 */ + case MXC_CPU_MX6SOLO: + return "6SOLO"; /* Solo version of the mx6 */ + case MXC_CPU_MX6SL: return "6SL"; /* Solo-Lite version of the mx6 */ - case 0x51: + case MXC_CPU_MX51: return "51"; - case 0x53: + case MXC_CPU_MX53: return "53"; default: return "??"; diff --git a/arch/arm/include/asm/arch-mx5/sys_proto.h b/arch/arm/include/asm/arch-mx5/sys_proto.h index 7b5246e..4435be1 100644 --- a/arch/arm/include/asm/arch-mx5/sys_proto.h +++ b/arch/arm/include/asm/arch-mx5/sys_proto.h @@ -24,8 +24,15 @@ #ifndef _SYS_PROTO_H_ #define _SYS_PROTO_H_

-u32 get_cpu_rev(void); +#define MXC_CPU_MX51 0x51 +#define MXC_CPU_MX53 0x53 +#define MXC_CPU_MX6SL 0x60 +#define MXC_CPU_MX6DL 0x61 +#define MXC_CPU_MX6SOLO 0x62 +#define MXC_CPU_MX6Q 0x63 + #define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) +u32 get_cpu_rev(void); void sdelay(unsigned long); void set_chipselect_size(int const);

diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h index 09ab010..3eb0081 100644 --- a/arch/arm/include/asm/arch-mx6/imx-regs.h +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h @@ -564,6 +564,8 @@ struct anatop_regs { u32 usb2_misc_clr; /* 0x258 */ u32 usb2_misc_tog; /* 0x25c */ u32 digprog; /* 0x260 */ + u32 reserved1[7]; + u32 digprog_sololite; /* 0x280 */ };

#define ANATOP_PFD_480_PFD0_FRAC_SHIFT 0 diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h index 711b30d..6627bbc 100644 --- a/arch/arm/include/asm/arch-mx6/sys_proto.h +++ b/arch/arm/include/asm/arch-mx6/sys_proto.h @@ -24,9 +24,16 @@ #ifndef _SYS_PROTO_H_ #define _SYS_PROTO_H_

-#define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) +#define MXC_CPU_MX51 0x51 +#define MXC_CPU_MX53 0x53 +#define MXC_CPU_MX6SL 0x60 +#define MXC_CPU_MX6DL 0x61 +#define MXC_CPU_MX6SOLO 0x62 +#define MXC_CPU_MX6Q 0x63

+#define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) u32 get_cpu_rev(void); +const char *get_imx_type(u32 imxtype);

void set_vddsoc(u32 mv);

-- 1.7.9.5

Reply

Troy Kisky

23 Oct 23 Oct

10:57 p.m.

New subject: [U-Boot] [PATCH V1 2/5] mx6: use CONFIG_MX6 instead of CONFIG_MX6Q

Use CONFIG_MX6 when the particular processor variant isn't important.

Reserve the use of CONFIG_MX6Q to specifically test for quad cores variant.

Signed-off-by: Troy Kisky troy.kisky@boundarydevices.com --- drivers/gpio/mxc_gpio.c | 6 +++--- drivers/video/ipu_regs.h | 2 +- include/configs/mx6qarm2.h | 1 + include/configs/mx6qsabre_common.h | 1 + include/configs/mx6qsabrelite.h | 1 + 5 files changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/gpio/mxc_gpio.c b/drivers/gpio/mxc_gpio.c index 2c79bff..a388064 100644 --- a/drivers/gpio/mxc_gpio.c +++ b/drivers/gpio/mxc_gpio.c @@ -42,14 +42,14 @@ static unsigned long gpio_ports[] = { [1] = GPIO2_BASE_ADDR, [2] = GPIO3_BASE_ADDR, #if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX51) || \ - defined(CONFIG_MX53) || defined(CONFIG_MX6Q) + defined(CONFIG_MX53) || defined(CONFIG_MX6) [3] = GPIO4_BASE_ADDR, #endif -#if defined(CONFIG_MX27) || defined(CONFIG_MX53) || defined(CONFIG_MX6Q) +#if defined(CONFIG_MX27) || defined(CONFIG_MX53) || defined(CONFIG_MX6) [4] = GPIO5_BASE_ADDR, [5] = GPIO6_BASE_ADDR, #endif -#if defined(CONFIG_MX53) || defined(CONFIG_MX6Q) +#if defined(CONFIG_MX53) || defined(CONFIG_MX6) [6] = GPIO7_BASE_ADDR, #endif }; diff --git a/drivers/video/ipu_regs.h b/drivers/video/ipu_regs.h index a43aa03..982e252 100644 --- a/drivers/video/ipu_regs.h +++ b/drivers/video/ipu_regs.h @@ -55,7 +55,7 @@ #define IPU_TPM_REG_BASE 0x01060000 #define IPU_DC_TMPL_REG_BASE 0x01080000 #define IPU_ISP_TBPR_REG_BASE 0x010C0000 -#elif defined(CONFIG_MX6Q) +#elif defined(CONFIG_MX6) #define IPU_CPMEM_REG_BASE 0x00100000 #define IPU_LUT_REG_BASE 0x00120000 #define IPU_SRM_REG_BASE 0x00140000 diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h index b425fed..e8ce6db 100644 --- a/include/configs/mx6qarm2.h +++ b/include/configs/mx6qarm2.h @@ -22,6 +22,7 @@ #ifndef __CONFIG_H #define __CONFIG_H

+#define CONFIG_MX6 #define CONFIG_MX6Q #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO diff --git a/include/configs/mx6qsabre_common.h b/include/configs/mx6qsabre_common.h index bfb9cd4..75eeda5 100644 --- a/include/configs/mx6qsabre_common.h +++ b/include/configs/mx6qsabre_common.h @@ -17,6 +17,7 @@ #ifndef __MX6QSABRE_COMMON_CONFIG_H #define __MX6QSABRE_COMMON_CONFIG_H

+#define CONFIG_MX6 #define CONFIG_MX6Q #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h index 5989eb2..3ce6cf7 100644 --- a/include/configs/mx6qsabrelite.h +++ b/include/configs/mx6qsabrelite.h @@ -22,6 +22,7 @@ #ifndef __CONFIG_H #define __CONFIG_H

+#define CONFIG_MX6 #define CONFIG_MX6Q #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO

-- 1.7.9.5

Reply

Troy Kisky

23 Oct 23 Oct

10:57 p.m.

New subject: [U-Boot] [PATCH V1 3/5] imx-common: cpu: add imx_ddr_size

Read memory setup registers to determine size of available ram. This routine works for mx53/mx6x

I need this because when mx6solo called get_ram_size with a too large maximum size, the system hanged.

Signed-off-by: Troy Kisky troy.kisky@boundarydevices.com

--- --- arch/arm/imx-common/cpu.c | 50 +++++++++++++++++++++++++++++ arch/arm/include/asm/arch-mx5/sys_proto.h | 1 + arch/arm/include/asm/arch-mx6/sys_proto.h | 1 + 3 files changed, 52 insertions(+)

diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c index 102c254..5081908 100644 --- a/arch/arm/imx-common/cpu.c +++ b/arch/arm/imx-common/cpu.c @@ -65,6 +65,56 @@ char *get_reset_cause(void) } }

+#if defined(CONFIG_MX53) || defined(CONFIG_MX6) +#if defined(CONFIG_MX53) +#define MEMCTL_BASE ESDCTL_BASE_ADDR; +#else +#define MEMCTL_BASE MMDC_P0_BASE_ADDR; +#endif +static const unsigned char col_lookup[] = {9, 10, 11, 8, 12, 9, 9, 9}; +static const unsigned char bank_lookup[] = {3, 2}; + +struct esd_mmdc_regs { + uint32_t ctl; + uint32_t pdc; + uint32_t otc; + uint32_t cfg0; + uint32_t cfg1; + uint32_t cfg2; + uint32_t misc; + uint32_t scr; + uint32_t ref; + uint32_t rsvd1; + uint32_t rsvd2; + uint32_t rwd; + uint32_t or; + uint32_t mrr; + uint32_t cfg3lp; + uint32_t mr4; +}; + +#define ESD_MMDC_CTL_GET_ROW(mdctl) ((ctl >> 24) & 7) +#define ESD_MMDC_CTL_GET_COLUMN(mdctl) ((ctl >> 20) & 7) +#define ESD_MMDC_CTL_GET_WIDTH(mdctl) ((ctl >> 16) & 3) +#define ESD_MMDC_CTL_GET_CS1(mdctl) ((ctl >> 30) & 1) +#define ESD_MMDC_MISC_GET_BANK(mdmisc) ((misc >> 5) & 1) + +unsigned imx_ddr_size(void) +{ + struct esd_mmdc_regs *mem = (struct esd_mmdc_regs *)MEMCTL_BASE; + unsigned ctl = readl(&mem->ctl); + unsigned misc = readl(&mem->misc); + int bits = 11 + 0 + 0 + 1; /* row + col + bank + width */ + + bits += ESD_MMDC_CTL_GET_ROW(ctl); + bits += col_lookup[ESD_MMDC_CTL_GET_COLUMN(ctl)]; + bits += bank_lookup[ESD_MMDC_MISC_GET_BANK(misc)]; + bits += ESD_MMDC_CTL_GET_WIDTH(ctl); + bits += ESD_MMDC_CTL_GET_CS1(ctl); + return 1 << bits; +} +#endif + #if defined(CONFIG_DISPLAY_CPUINFO)

const char *get_imx_type(u32 imxtype) diff --git a/arch/arm/include/asm/arch-mx5/sys_proto.h b/arch/arm/include/asm/arch-mx5/sys_proto.h index 4435be1..93ad1c6 100644 --- a/arch/arm/include/asm/arch-mx5/sys_proto.h +++ b/arch/arm/include/asm/arch-mx5/sys_proto.h @@ -33,6 +33,7 @@

#define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) u32 get_cpu_rev(void); +unsigned imx_ddr_size(void); void sdelay(unsigned long); void set_chipselect_size(int const);

diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h index 6627bbc..3193297 100644 --- a/arch/arm/include/asm/arch-mx6/sys_proto.h +++ b/arch/arm/include/asm/arch-mx6/sys_proto.h @@ -34,6 +34,7 @@ #define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) u32 get_cpu_rev(void); const char *get_imx_type(u32 imxtype); +unsigned imx_ddr_size(void);

void set_vddsoc(u32 mv);

-- 1.7.9.5

Reply

Troy Kisky

23 Oct 23 Oct

10:57 p.m.

New subject: [U-Boot] [PATCH V1 4/5] arch-mx6: add mx6dl_pins.h

Only the values used in the sabrelite board are added currently. Add more as other boards use them.

Signed-off-by: Troy Kisky troy.kisky@boundarydevices.com --- arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 149 ++++++++++++++++++++++++++++ 1 file changed, 149 insertions(+) create mode 100644 arch/arm/include/asm/arch-mx6/mx6dl_pins.h

diff --git a/arch/arm/include/asm/arch-mx6/mx6dl_pins.h b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h new file mode 100644 index 0000000..79e2c4f --- /dev/null +++ b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h @@ -0,0 +1,149 @@ +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + * + */ + +#ifndef __ASM_ARCH_MX6_MX6DL_PINS_H__ +#define __ASM_ARCH_MX6_MX6DL_PINS_H__ + +#include <asm/imx-common/iomux-v3.h> + +/* Use to set PAD control */ +#define PAD_CTL_HYS (1 << 16) +#define PAD_CTL_PUS_100K_DOWN (0 << 14) +#define PAD_CTL_PUS_47K_UP (1 << 14) +#define PAD_CTL_PUS_100K_UP (2 << 14) +#define PAD_CTL_PUS_22K_UP (3 << 14) + +#define PAD_CTL_PUE (1 << 13) +#define PAD_CTL_PKE (1 << 12) +#define PAD_CTL_ODE (1 << 11) +#define PAD_CTL_SPEED_LOW (1 << 6) +#define PAD_CTL_SPEED_MED (2 << 6) +#define PAD_CTL_SPEED_HIGH (3 << 6) +#define PAD_CTL_DSE_DISABLE (0 << 3) +#define PAD_CTL_DSE_240ohm (1 << 3) +#define PAD_CTL_DSE_120ohm (2 << 3) +#define PAD_CTL_DSE_80ohm (3 << 3) +#define PAD_CTL_DSE_60ohm (4 << 3) +#define PAD_CTL_DSE_48ohm (5 << 3) +#define PAD_CTL_DSE_40ohm (6 << 3) +#define PAD_CTL_DSE_34ohm (7 << 3) +#define PAD_CTL_SRE_FAST (1 << 0) +#define PAD_CTL_SRE_SLOW (0 << 0) + +#define IOMUX_CONFIG_SION 0x10 +#define NO_MUX_I 0 +#define NO_PAD_I 0 +enum { + MX6DL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK = IOMUX_PAD(0x03B0, 0x009C, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DI0_PIN15__IPU1_DI0_PIN15 = IOMUX_PAD(0x03B4, 0x00A0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DI0_PIN2__IPU1_DI0_PIN2 = IOMUX_PAD(0x03B8, 0x00A4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DI0_PIN3__IPU1_DI0_PIN3 = IOMUX_PAD(0x03BC, 0x00A8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DI0_PIN4__GPIO_4_20 = IOMUX_PAD(0x03C0, 0x00AC, 5, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT0__IPU1_DISP0_DAT_0 = IOMUX_PAD(0x03C4, 0x00B0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT1__IPU1_DISP0_DAT_1 = IOMUX_PAD(0x03C8, 0x00B4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT10__IPU1_DISP0_DAT_10 = IOMUX_PAD(0x03CC, 0x00B8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT11__IPU1_DISP0_DAT_11 = IOMUX_PAD(0x03D0, 0x00BC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT12__IPU1_DISP0_DAT_12 = IOMUX_PAD(0x03D4, 0x00C0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT13__IPU1_DISP0_DAT_13 = IOMUX_PAD(0x03D8, 0x00C4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT14__IPU1_DISP0_DAT_14 = IOMUX_PAD(0x03DC, 0x00C8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT15__IPU1_DISP0_DAT_15 = IOMUX_PAD(0x03E0, 0x00CC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT16__IPU1_DISP0_DAT_16 = IOMUX_PAD(0x03E4, 0x00D0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT17__IPU1_DISP0_DAT_17 = IOMUX_PAD(0x03E8, 0x00D4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT18__IPU1_DISP0_DAT_18 = IOMUX_PAD(0x03EC, 0x00D8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT19__IPU1_DISP0_DAT_19 = IOMUX_PAD(0x03F0, 0x00DC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT2__IPU1_DISP0_DAT_2 = IOMUX_PAD(0x03F4, 0x00E0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT20__IPU1_DISP0_DAT_20 = IOMUX_PAD(0x03F8, 0x00E4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT21__IPU1_DISP0_DAT_21 = IOMUX_PAD(0x03FC, 0x00E8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT22__IPU1_DISP0_DAT_22 = IOMUX_PAD(0x0400, 0x00EC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT23__IPU1_DISP0_DAT_23 = IOMUX_PAD(0x0404, 0x00F0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT3__IPU1_DISP0_DAT_3 = IOMUX_PAD(0x0408, 0x00F4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT4__IPU1_DISP0_DAT_4 = IOMUX_PAD(0x040C, 0x00F8, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT5__IPU1_DISP0_DAT_5 = IOMUX_PAD(0x0410, 0x00FC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT6__IPU1_DISP0_DAT_6 = IOMUX_PAD(0x0414, 0x0100, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT7__IPU1_DISP0_DAT_7 = IOMUX_PAD(0x0418, 0x0104, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT8__IPU1_DISP0_DAT_8 = IOMUX_PAD(0x041C, 0x0108, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_DISP0_DAT9__IPU1_DISP0_DAT_9 = IOMUX_PAD(0x0420, 0x010C, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), + MX6DL_PAD_EIM_D16__ECSPI1_SCLK = IOMUX_PAD(0x0514, 0x0144, 1, 0x07D8, 2, 0), + MX6DL_PAD_EIM_D17__ECSPI1_MISO = IOMUX_PAD(0x0518, 0x0148, 1, 0x07DC, 2, 0), + MX6DL_PAD_EIM_D18__ECSPI1_MOSI = IOMUX_PAD(0x051C, 0x014C, 1, 0x07E0, 2, 0), + MX6DL_PAD_EIM_D19__GPIO_3_19 = IOMUX_PAD(0x0520, 0x0150, 5, 0x0000, 0, 0), + MX6DL_PAD_EIM_D21__GPIO_3_21 = IOMUX_PAD(0x0528, 0x0158, 5, 0x0000, 0, 0), + MX6DL_PAD_EIM_D21__I2C1_SCL = IOMUX_PAD(0x0528, 0x0158, 6 | IOMUX_CONFIG_SION, 0x0868, 1, 0), + MX6DL_PAD_EIM_D23__GPIO_3_23 = IOMUX_PAD(0x0530, 0x0160, 5, 0x0000, 0, 0), + MX6DL_PAD_EIM_D26__UART2_TXD = IOMUX_PAD(0x053C, 0x016C, 4, 0x0000, 0, 0), + MX6DL_PAD_EIM_D27__UART2_RXD = IOMUX_PAD(0x0540, 0x0170, 4, 0x0904, 1, 0), + MX6DL_PAD_EIM_D28__I2C1_SDA = IOMUX_PAD(0x0544, 0x0174, 1 | IOMUX_CONFIG_SION, 0x086C, 1, 0), + MX6DL_PAD_EIM_D28__GPIO_3_28 = IOMUX_PAD(0x0544, 0x0174, 5, 0x0000, 0, 0), + MX6DL_PAD_ENET_MDC__ENET_MDC = IOMUX_PAD(0x05B8, 0x01E8, 1, 0x0000, 0, 0), + MX6DL_PAD_ENET_MDIO__ENET_MDIO = IOMUX_PAD(0x05BC, 0x01EC, 1, 0x0810, 0, 0), + MX6DL_PAD_ENET_REF_CLK__ENET_TX_CLK = IOMUX_PAD(0x05C0, 0x01F0, 1, 0x0000, 0, 0), + MX6DL_PAD_ENET_RXD0__GPIO_1_27 = IOMUX_PAD(0x05C8, 0x01F8, 5, 0x0000, 0, 0), + MX6DL_PAD_GPIO_16__GPIO_7_11 = IOMUX_PAD(0x05E4, 0x0214, 5, 0x0000, 0, 0), + MX6DL_PAD_GPIO_16__I2C3_SDA = IOMUX_PAD(0x05E4, 0x0214, 6 | IOMUX_CONFIG_SION, 0x087C, 1, 0), + MX6DL_PAD_GPIO_17__GPIO_7_12 = IOMUX_PAD(0x05E8, 0x0218, 5, 0x0000, 0, 0), + MX6DL_PAD_GPIO_18__GPIO_7_13 = IOMUX_PAD(0x05EC, 0x021C, 5, 0x0000, 0, 0), + MX6DL_PAD_GPIO_19__GPIO_4_5 = IOMUX_PAD(0x05F0, 0x0220, 5, 0x0000, 0, 0), + MX6DL_PAD_GPIO_5__GPIO_1_5 = IOMUX_PAD(0x0600, 0x0230, 5, 0x0000, 0, 0), + MX6DL_PAD_GPIO_5__I2C3_SCL = IOMUX_PAD(0x0600, 0x0230, 6 | IOMUX_CONFIG_SION, 0x0878, 2, 0), + MX6DL_PAD_KEY_COL3__I2C2_SCL = IOMUX_PAD(0x0638, 0x0250, 4 | IOMUX_CONFIG_SION, 0x0870, 1, 0), + MX6DL_PAD_KEY_COL3__GPIO_4_12 = IOMUX_PAD(0x0638, 0x0250, 5, 0x0000, 0, 0), + MX6DL_PAD_KEY_ROW3__I2C2_SDA = IOMUX_PAD(0x064C, 0x0264, 4 | IOMUX_CONFIG_SION, 0x0874, 1, 0), + MX6DL_PAD_KEY_ROW3__GPIO_4_13 = IOMUX_PAD(0x064C, 0x0264, 5, 0x0000, 0, 0), + MX6DL_PAD_NANDF_D1__GPIO_2_1 = IOMUX_PAD(0x0670, 0x0288, 5, 0x0000, 0, 0), + MX6DL_PAD_NANDF_D2__GPIO_2_2 = IOMUX_PAD(0x0674, 0x028C, 5, 0x0000, 0, 0), + MX6DL_PAD_NANDF_D3__GPIO_2_3 = IOMUX_PAD(0x0678, 0x0290, 5, 0x0000, 0, 0), + MX6DL_PAD_NANDF_D4__GPIO_2_4 = IOMUX_PAD(0x067C, 0x0294, 5, 0x0000, 0, 0), + MX6DL_PAD_NANDF_D6__GPIO_2_6 = IOMUX_PAD(0x0684, 0x029C, 5, 0x0000, 0, 0), + MX6DL_PAD_RGMII_RD0__ENET_RGMII_RD0 = IOMUX_PAD(0x0694, 0x02AC, 1, 0x0818, 1, 0), + MX6DL_PAD_RGMII_RD0__GPIO_6_25 = IOMUX_PAD(0x0694, 0x02AC, 5, 0x0000, 0, 0), + MX6DL_PAD_RGMII_RD1__ENET_RGMII_RD1 = IOMUX_PAD(0x0698, 0x02B0, 1, 0x081C, 1, 0), + MX6DL_PAD_RGMII_RD1__GPIO_6_27 = IOMUX_PAD(0x0698, 0x02B0, 5, 0x0000, 0, 0), + MX6DL_PAD_RGMII_RD2__ENET_RGMII_RD2 = IOMUX_PAD(0x069C, 0x02B4, 1, 0x0820, 1, 0), + MX6DL_PAD_RGMII_RD2__GPIO_6_28 = IOMUX_PAD(0x069C, 0x02B4, 5, 0x0000, 0, 0), + MX6DL_PAD_RGMII_RD3__ENET_RGMII_RD3 = IOMUX_PAD(0x06A0, 0x02B8, 1, 0x0824, 1, 0), + MX6DL_PAD_RGMII_RD3__GPIO_6_29 = IOMUX_PAD(0x06A0, 0x02B8, 5, 0x0000, 0, 0), + MX6DL_PAD_RGMII_RX_CTL__RGMII_RX_CTL = IOMUX_PAD(0x06A4, 0x02BC, 1, 0x0828, 1, 0), + MX6DL_PAD_RGMII_RX_CTL__GPIO_6_24 = IOMUX_PAD(0x06A4, 0x02BC, 5, 0x0000, 0, 0), + MX6DL_PAD_RGMII_RXC__ENET_RGMII_RXC = IOMUX_PAD(0x06A8, 0x02C0, 1, 0x0814, 1, 0), + MX6DL_PAD_RGMII_RXC__GPIO_6_30 = IOMUX_PAD(0x06A8, 0x02C0, 5, 0x0000, 0, 0), + MX6DL_PAD_RGMII_TD0__ENET_RGMII_TD0 = IOMUX_PAD(0x06AC, 0x02C4, 1, 0x0000, 0, 0), + MX6DL_PAD_RGMII_TD1__ENET_RGMII_TD1 = IOMUX_PAD(0x06B0, 0x02C8, 1, 0x0000, 0, 0), + MX6DL_PAD_RGMII_TD2__ENET_RGMII_TD2 = IOMUX_PAD(0x06B4, 0x02CC, 1, 0x0000, 0, 0), + MX6DL_PAD_RGMII_TD3__ENET_RGMII_TD3 = IOMUX_PAD(0x06B8, 0x02D0, 1, 0x0000, 0, 0), + MX6DL_PAD_RGMII_TX_CTL__RGMII_TX_CTL = IOMUX_PAD(0x06BC, 0x02D4, 1, 0x0000, 0, 0), + MX6DL_PAD_RGMII_TXC__ENET_RGMII_TXC = IOMUX_PAD(0x06C0, 0x02D8, 1, 0x0000, 0, 0), + MX6DL_PAD_SD1_CMD__GPIO_1_18 = IOMUX_PAD(0x06C8, 0x02E0, 5, 0x0000, 0, 0), + MX6DL_PAD_SD1_DAT3__GPIO_1_21 = IOMUX_PAD(0x06D8, 0x02F0, 5, 0x0000, 0, 0), + MX6DL_PAD_SD3_CLK__USDHC3_CLK = IOMUX_PAD(0x06F4, 0x030C, 0, 0x0934, 1, 0), + MX6DL_PAD_SD3_CMD__USDHC3_CMD = IOMUX_PAD(0x06F8, 0x0310, 0 | IOMUX_CONFIG_SION, 0x0000, 0, 0), + MX6DL_PAD_SD3_DAT0__USDHC3_DAT0 = IOMUX_PAD(0x06FC, 0x0314, 0, 0x0000, 0, 0), + MX6DL_PAD_SD3_DAT1__USDHC3_DAT1 = IOMUX_PAD(0x0700, 0x0318, 0, 0x0000, 0, 0), + MX6DL_PAD_SD3_DAT2__USDHC3_DAT2 = IOMUX_PAD(0x0704, 0x031C, 0, 0x0000, 0, 0), + MX6DL_PAD_SD3_DAT3__USDHC3_DAT3 = IOMUX_PAD(0x0708, 0x0320, 0, 0x0000, 0, 0), + MX6DL_PAD_SD3_DAT5__GPIO_7_0 = IOMUX_PAD(0x0710, 0x0328, 5, 0x0000, 0, 0), + MX6DL_PAD_SD3_DAT6__UART1_RXD = IOMUX_PAD(0x0714, 0x032C, 1, 0x08FC, 2, 0), + MX6DL_PAD_SD3_DAT7__UART1_TXD = IOMUX_PAD(0x0718, 0x0330, 1, 0x0000, 0, 0), + MX6DL_PAD_SD4_CLK__USDHC4_CLK = IOMUX_PAD(0x0720, 0x0338, 0, 0x0938, 1, 0), + MX6DL_PAD_SD4_CMD__USDHC4_CMD = IOMUX_PAD(0x0724, 0x033C, 0 | IOMUX_CONFIG_SION, 0x0000, 0, 0), + MX6DL_PAD_SD4_DAT0__USDHC4_DAT0 = IOMUX_PAD(0x0728, 0x0340, 1, 0x0000, 0, 0), + MX6DL_PAD_SD4_DAT1__USDHC4_DAT1 = IOMUX_PAD(0x072C, 0x0344, 1, 0x0000, 0, 0), + MX6DL_PAD_SD4_DAT2__USDHC4_DAT2 = IOMUX_PAD(0x0730, 0x0348, 1, 0x0000, 0, 0), + MX6DL_PAD_SD4_DAT3__USDHC4_DAT3 = IOMUX_PAD(0x0734, 0x034C, 1, 0x0000, 0, 0), +}; +#endif /* __ASM_ARCH_MX6_MX6DL_PINS_H__ */

-- 1.7.9.5

Reply

Troy Kisky

23 Oct 23 Oct

10:57 p.m.

New subject: [U-Boot] [PATCH V1 5/5] imximage.cfg: run files through C preprocessor

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.

Signed-off-by: Troy Kisky troy.kisky@boundarydevices.com --- .gitignore | 1 + Makefile | 11 +- board/esg/ima3-mx53/imximage.cfg | 120 ++++++----- board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg | 90 ++++---- board/freescale/mx25pdk/imximage.cfg | 77 +++---- board/freescale/mx51evk/imximage.cfg | 114 +++++----- board/freescale/mx53ard/imximage_dd3.cfg | 83 ++++---- board/freescale/mx53evk/imximage.cfg | 86 ++++---- board/freescale/mx53loco/imximage.cfg | 83 ++++---- board/freescale/mx53smd/imximage.cfg | 83 ++++---- board/freescale/mx6qarm2/imximage.cfg | 88 ++++---- board/freescale/mx6qsabreauto/imximage.cfg | 82 +++---- board/genesi/mx51_efikamx/imximage_mx.cfg | 132 ++++++------ board/genesi/mx51_efikamx/imximage_sb.cfg | 126 +++++------ board/ttcontrol/vision2/imximage_hynix.cfg | 295 ++++++++++++++------------ 15 files changed, 777 insertions(+), 694 deletions(-)

diff --git a/.gitignore b/.gitignore index d91e91b..be09894 100644 --- a/.gitignore +++ b/.gitignore @@ -15,6 +15,7 @@ *.swp *.patch *.bin +*.cfgtmp

# Build tree /build-* diff --git a/Makefile b/Makefile index 08eecbb..dce8239 100644 --- a/Makefile +++ b/Makefile @@ -450,8 +450,12 @@ $(obj)u-boot.img: $(obj)u-boot.bin sed -e 's/"[ ]*$$/ for $(BOARD) board"/') \ -d $< $@

-$(obj)u-boot.imx: $(obj)u-boot.bin - $(obj)tools/mkimage -n $(CONFIG_IMX_CONFIG) -T imximage \ +$(obj)$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp: $(obj)%.cfgtmp : % + mkdir -p $(dir $@) + $(CC) -E -x c $< $(CPPFLAGS) -o $@ + +$(obj)u-boot.imx: %.imx : %.bin $(obj)$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp + $(obj)tools/mkimage -n $(filter-out %.bin,$^) -T imximage \ -e $(CONFIG_SYS_TEXT_BASE) -d $< $@

$(obj)u-boot.kwb: $(obj)u-boot.bin @@ -819,7 +823,8 @@ clean: @$(MAKE) -C doc/DocBook/ cleandocs @find $(OBJTREE) -type f \ ( -name 'core' -o -name '*.bak' -o -name '*~' -o -name '*.su' \ - -o -name '*.o' -o -name '*.a' -o -name '*.exe' ) -print \ + -o -name '*.o' -o -name '*.a' -o -name '*.exe' \ + -o -name '*.cfgtmp' ) -print \ | xargs rm -f

# Removes everything not needed for testing u-boot diff --git a/board/esg/ima3-mx53/imximage.cfg b/board/esg/ima3-mx53/imximage.cfg index fa6b42d..fce7492 100644 --- a/board/esg/ima3-mx53/imximage.cfg +++ b/board/esg/ima3-mx53/imximage.cfg @@ -1,50 +1,52 @@ -# -# (C) Copyright 2012 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version +/* + * (C) Copyright 2012 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

+/* image version */ IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM nor

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register - -# IOMUX for RAM only +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +/* IOMUX for RAM only */ DATA 4 0x53fa8554 0x300020 DATA 4 0x53fa8560 0x300020 DATA 4 0x53fa8594 0x300020 @@ -72,37 +74,47 @@ DATA 4 0x53fa86fc 0x0 DATA 4 0x53fa86f4 0x0 DATA 4 0x53fa8714 0x0 DATA 4 0x53fa8724 0x4000000 -# -# DDR RAM + +/* DDR RAM */ DATA 4 0x63fd9088 0x40404040 DATA 4 0x63fd9090 0x40404040 DATA 4 0x63fd907C 0x01420143 DATA 4 0x63fd9080 0x01450146 DATA 4 0x63fd9018 0x00111740 DATA 4 0x63fd9000 0x84190000 -# esdcfgX + +/* esdcfgX */ DATA 4 0x63fd900C 0x9f5152e3 DATA 4 0x63fd9010 0xb68e8a63 DATA 4 0x63fd9014 0x01ff00db -# Read/Write command delay + +/* Read/Write command delay */ DATA 4 0x63fd902c 0x000026d2 -# Out of reset delays + +/* Out of reset delays */ DATA 4 0x63fd9030 0x00ff0e21 -# ESDCTL ODT timing control + +/* ESDCTL ODT timing control */ DATA 4 0x63fd9008 0x12273030 -# ESDCTL power down control + +/* ESDCTL power down control */ DATA 4 0x63fd9004 0x0002002d -# Set registers in DDR memory chips + +/* Set registers in DDR memory chips */ DATA 4 0x63fd901c 0x00008032 DATA 4 0x63fd901c 0x00008033 DATA 4 0x63fd901c 0x00028031 DATA 4 0x63fd901c 0x052080b0 DATA 4 0x63fd901c 0x04008040 -# ESDCTL refresh control + +/* ESDCTL refresh control */ DATA 4 0x63fd9020 0x00005800 -# PHY ZQ HW control + +/* PHY ZQ HW control */ DATA 4 0x63fd9040 0x05380003 -# PHY ODT control + +/* PHY ODT control */ DATA 4 0x63fd9058 0x00022222 -# start DDR3 + +/* start DDR3 */ DATA 4 0x63fd901c 0x00000000 diff --git a/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg b/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg index 62498ab..c86cd40 100644 --- a/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +++ b/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg @@ -1,47 +1,51 @@ -# Copyright (C) 2011 Freescale Semiconductor, Inc. -# Jason Liu r64343@freescale.com -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version - +/* + * Copyright (C) 2011 Freescale Semiconductor, Inc. + * Jason Liu r64343@freescale.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* image version */ IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ DATA 4 0x020e05a8 0x00000030 DATA 4 0x020e05b0 0x00000030 DATA 4 0x020e0524 0x00000030 @@ -154,7 +158,7 @@ DATA 4 0x021b48b8 0x00000800 DATA 4 0x021b001c 0x00000000 DATA 4 0x021b0404 0x00011006

-# set the default clock gate to save power +/* set the default clock gate to save power */ DATA 4 0x020c4068 0x00C03F3F DATA 4 0x020c406c 0x0030FC03 DATA 4 0x020c4070 0x0FFFC000 @@ -163,8 +167,8 @@ DATA 4 0x020c4078 0x00FFF300 DATA 4 0x020c407c 0x0F0000C3 DATA 4 0x020c4080 0x000003FF

-# enable AXI cache for VDOA/VPU/IPU +/* enable AXI cache for VDOA/VPU/IPU */ DATA 4 0x020e0010 0xF00000CF -# set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ DATA 4 0x020e0018 0x007F007F DATA 4 0x020e001c 0x007F007F diff --git a/board/freescale/mx25pdk/imximage.cfg b/board/freescale/mx25pdk/imximage.cfg index f7af7ff..c42a283 100644 --- a/board/freescale/mx25pdk/imximage.cfg +++ b/board/freescale/mx25pdk/imximage.cfg @@ -1,46 +1,49 @@ -# -# (C) Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# Boot Device : one of -# spi, sd (the board has no nand neither onenand) +/* + * (C) Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

+/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register - -# EIM config-CS5 init -- CPLD +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +/* EIM config-CS5 init -- CPLD */ DATA 4 0xB8002050 0x0000D843 DATA 4 0xB8002054 0x22252521 DATA 4 0xB8002058 0x22220A00

-# DDR2 init +/* DDR2 init */ DATA 4 0xB8001004 0x0076E83A DATA 4 0xB8001010 0x00000204 DATA 4 0xB8001000 0x92210000 @@ -67,7 +70,7 @@ DATA 4 0x43FAC454 0x00001000

DATA 4 0x53F80008 0x20034000

-# Enable the clocks +/* Enable the clocks */ DATA 4 0x53f8000c 0x1fffffff DATA 4 0x53f80010 0xffffffff DATA 4 0x53f80014 0xfdfff diff --git a/board/freescale/mx51evk/imximage.cfg b/board/freescale/mx51evk/imximage.cfg index a875e8f..3e141ee 100644 --- a/board/freescale/mx51evk/imximage.cfg +++ b/board/freescale/mx51evk/imximage.cfg @@ -1,46 +1,50 @@ -# -# (C Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# Boot Device : one of -# spi, sd (the board has no nand neither onenand) +/* + * (C Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

+/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM spi

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */

-# Setting IOMUXC +/* Setting IOMUXC */ DATA 4 0x73FA88a0 0x200 DATA 4 0x73FA850c 0x20c5 DATA 4 0x73FA8510 0x20c5 @@ -65,22 +69,24 @@ DATA 4 0x73FA88a4 0x6 DATA 4 0x73FA88ac 0x6 DATA 4 0x73FA88b8 0x6

-# Setting DDR for micron -# 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model -# CAS=3 BL=4 -# ESDCTL_ESDCTL0 +/* + * Setting DDR for micron + * 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model + * CAS=3 BL=4 + */ +/* ESDCTL_ESDCTL0 */ DATA 4 0x83FD9000 0x82a20000 -# ESDCTL_ESDCTL1 +/* ESDCTL_ESDCTL1 */ DATA 4 0x83FD9008 0x82a20000 -# ESDCTL_ESDMISC +/* ESDCTL_ESDMISC */ DATA 4 0x83FD9010 0x000ad0d0 -# ESDCTL_ESDCFG0 +/* ESDCTL_ESDCFG0 */ DATA 4 0x83FD9004 0x333574aa -# ESDCTL_ESDCFG1 +/* ESDCTL_ESDCFG1 */ DATA 4 0x83FD900C 0x333574aa

-# Init DRAM on CS0 -# ESDCTL_ESDSCR +/* Init DRAM on CS0 */ +/* ESDCTL_ESDSCR */ DATA 4 0x83FD9014 0x04008008 DATA 4 0x83FD9014 0x0000801a DATA 4 0x83FD9014 0x0000801b @@ -94,7 +100,7 @@ DATA 4 0x83FD9014 0x03808019 DATA 4 0x83FD9014 0x00408019 DATA 4 0x83FD9014 0x00008000

-# Init DRAM on CS1 +/* Init DRAM on CS1 */ DATA 4 0x83FD9014 0x0400800c DATA 4 0x83FD9014 0x0000801e DATA 4 0x83FD9014 0x0000801f @@ -108,12 +114,12 @@ DATA 4 0x83FD9014 0x0380801d DATA 4 0x83FD9014 0x0040801d DATA 4 0x83FD9014 0x00008004

-# Write to CTL0 +/* Write to CTL0 */ DATA 4 0x83FD9000 0xb2a20000 -# Write to CTL1 +/* Write to CTL1 */ DATA 4 0x83FD9008 0xb2a20000 -# ESDMISC +/* ESDMISC */ DATA 4 0x83FD9010 0x000ad6d0 -#ESDCTL_ESDCDLYGD +/* ESDCTL_ESDCDLYGD */ DATA 4 0x83FD9034 0x90000000 DATA 4 0x83FD9014 0x00000000 diff --git a/board/freescale/mx53ard/imximage_dd3.cfg b/board/freescale/mx53ard/imximage_dd3.cfg index 614d29e..4633e4d 100644 --- a/board/freescale/mx53ard/imximage_dd3.cfg +++ b/board/freescale/mx53ard/imximage_dd3.cfg @@ -1,48 +1,51 @@ -# -# (C) Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version +/* + * (C) Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

+/* image version */ IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ DATA 4 0x53fa8554 0x00300000 DATA 4 0x53fa8558 0x00300040 DATA 4 0x53fa8560 0x00300000 diff --git a/board/freescale/mx53evk/imximage.cfg b/board/freescale/mx53evk/imximage.cfg index 915fb2c..1cd61d5 100644 --- a/board/freescale/mx53evk/imximage.cfg +++ b/board/freescale/mx53evk/imximage.cfg @@ -1,50 +1,52 @@ -# -# (C Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version +/* + * (C Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

+/* image version */ IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register - -# Setting IOMUXC +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +/* Setting IOMUXC */ DATA 4 0x53fa8554 0x00200000 DATA 4 0x53fa8560 0x00200000 DATA 4 0x53fa8594 0x00200000 diff --git a/board/freescale/mx53loco/imximage.cfg b/board/freescale/mx53loco/imximage.cfg index 2ce5f8d..e6b90c1 100644 --- a/board/freescale/mx53loco/imximage.cfg +++ b/board/freescale/mx53loco/imximage.cfg @@ -1,48 +1,51 @@ -# Copyright (C) 2011 Freescale Semiconductor, Inc. -# Jason Liu r64343@freescale.com -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version +/* + * Copyright (C) 2011 Freescale Semiconductor, Inc. + * Jason Liu r64343@freescale.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

+/* image version */ IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register - +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ DATA 4 0x53fa8554 0x00300000 DATA 4 0x53fa8558 0x00300040 DATA 4 0x53fa8560 0x00300000 diff --git a/board/freescale/mx53smd/imximage.cfg b/board/freescale/mx53smd/imximage.cfg index 614d29e..4633e4d 100644 --- a/board/freescale/mx53smd/imximage.cfg +++ b/board/freescale/mx53smd/imximage.cfg @@ -1,48 +1,51 @@ -# -# (C) Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version +/* + * (C) Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

+/* image version */ IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ DATA 4 0x53fa8554 0x00300000 DATA 4 0x53fa8558 0x00300040 DATA 4 0x53fa8560 0x00300000 diff --git a/board/freescale/mx6qarm2/imximage.cfg b/board/freescale/mx6qarm2/imximage.cfg index bf941a3..4ed211e 100644 --- a/board/freescale/mx6qarm2/imximage.cfg +++ b/board/freescale/mx6qarm2/imximage.cfg @@ -1,47 +1,51 @@ -# Copyright (C) 2011 Freescale Semiconductor, Inc. -# Jason Liu r64343@freescale.com -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version - +/* + * Copyright (C) 2011 Freescale Semiconductor, Inc. + * Jason Liu r64343@freescale.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* image version */ IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ DATA 4 0x020e05a8 0x00000030 DATA 4 0x020e05b0 0x00000030 DATA 4 0x020e0524 0x00000030 @@ -166,8 +170,8 @@ DATA 4 0x020c4078 0x00FFF300 DATA 4 0x020c407c 0x0F0000C3 DATA 4 0x020c4080 0x000003FF

-# enable AXI cache for VDOA/VPU/IPU +/* enable AXI cache for VDOA/VPU/IPU */ DATA 4 0x020e0010 0xF00000CF -# set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ DATA 4 0x020e0018 0x007F007F DATA 4 0x020e001c 0x007F007F diff --git a/board/freescale/mx6qsabreauto/imximage.cfg b/board/freescale/mx6qsabreauto/imximage.cfg index d909aa8..bbff813 100644 --- a/board/freescale/mx6qsabreauto/imximage.cfg +++ b/board/freescale/mx6qsabreauto/imximage.cfg @@ -1,46 +1,50 @@ -# Copyright (C) 2012 Freescale Semiconductor, Inc. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ +/* image version */

IMAGE_VERSION 2

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) - +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM sd

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ DATA 4 0x020e05a8 0x00000028 DATA 4 0x020e05b0 0x00000028 DATA 4 0x020e0524 0x00000028 @@ -126,7 +130,7 @@ DATA 4 0x021b0020 0x00005800 DATA 4 0x021b0818 0x00000007 DATA 4 0x021b4818 0x00000007

-# Calibration values based on ARD and 528MHz +/* Calibration values based on ARD and 528MHz */ DATA 4 0x021b083c 0x434B0358 DATA 4 0x021b0840 0x033D033C DATA 4 0x021b483c 0x03520362 diff --git a/board/genesi/mx51_efikamx/imximage_mx.cfg b/board/genesi/mx51_efikamx/imximage_mx.cfg index 38fa760..21ff6d6 100644 --- a/board/genesi/mx51_efikamx/imximage_mx.cfg +++ b/board/genesi/mx51_efikamx/imximage_mx.cfg @@ -1,52 +1,58 @@ -# -# Copyright (C) 2009 Pegatron Corporation -# Copyright (C) 2010 Marek Vasut marek.vasut@gmail.com -# Copyright (C) 2009-2012 Genesi USA, Inc. -# -# BASED ON: imx51evk -# -# (C) Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage +/* + * Copyright (C) 2009 Pegatron Corporation + * Copyright (C) 2010 Marek Vasut marek.vasut@gmail.com + * Copyright (C) 2009-2012 Genesi USA, Inc. + * + * BASED ON: imx51evk + * + * (C) Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM spi

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register - -# Essential GPIO settings to be done as early as possible -# PCBIDn pad settings are all the defaults except #2 which needs HVE off +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +/* + * Essential GPIO settings to be done as early as possible + * PCBIDn pad settings are all the defaults except #2 which needs HVE off + */ DATA 4 0x73fa8134 0x3 # PCBID0 ALT3 GPIO 3_16 DATA 4 0x73fa8130 0x3 # PCBID1 ALT3 GPIO 3_17 DATA 4 0x73fa8128 0x3 # PCBID2 ALT3 GPIO 3_11 @@ -55,7 +61,7 @@ DATA 4 0x73fa8198 0x3 # LED0 ALT3 GPIO 3_13 DATA 4 0x73fa81c4 0x3 # LED1 ALT3 GPIO 3_14 DATA 4 0x73fa81c8 0x3 # LED2 ALT3 GPIO 3_15

-# DDR bus IOMUX PAD settings +/* DDR bus IOMUX PAD settings */ DATA 4 0x73fa850c 0x20c5 # SDODT1 DATA 4 0x73fa8510 0x20c5 # SDODT0 DATA 4 0x73fa84ac 0xc5 # SDWE @@ -72,22 +78,24 @@ DATA 4 0x73fa84d8 0xc5 # DRAM_DQM1 DATA 4 0x73fa84dc 0xc5 # DRAM_DQM2 DATA 4 0x73fa84e0 0xc5 # DRAM_DQM3

-# Setting DDR for micron -# 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model -# CAS=3 BL=4 -# ESDCTL_ESDCTL0 +/* + * Setting DDR for micron + * 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model + * CAS=3 BL=4 + */ +/* ESDCTL_ESDCTL0 */ DATA 4 0x83fd9000 0x82a20000 -# ESDCTL_ESDCTL1 +/* ESDCTL_ESDCTL1 */ DATA 4 0x83fd9008 0x82a20000 -# ESDCTL_ESDMISC +/* ESDCTL_ESDMISC */ DATA 4 0x83fd9010 0xcaaaf6d0 -# ESDCTL_ESDCFG0 +/* ESDCTL_ESDCFG0 */ DATA 4 0x83fd9004 0x3f3574aa -# ESDCTL_ESDCFG1 +/* ESDCTL_ESDCFG1 */ DATA 4 0x83fd900c 0x3f3574aa

-# Init DRAM on CS0 -# ESDCTL_ESDSCR +/* Init DRAM on CS0 */ +/* ESDCTL_ESDSCR */ DATA 4 0x83fd9014 0x04008008 DATA 4 0x83fd9014 0x0000801a DATA 4 0x83fd9014 0x0000801b @@ -101,7 +109,7 @@ DATA 4 0x83fd9014 0x03808019 DATA 4 0x83fd9014 0x00408019 DATA 4 0x83fd9014 0x00008000

-# Init DRAM on CS1 +/* Init DRAM on CS1 */ DATA 4 0x83fd9014 0x0400800c DATA 4 0x83fd9014 0x0000801e DATA 4 0x83fd9014 0x0000801f @@ -115,12 +123,12 @@ DATA 4 0x83fd9014 0x0380801d DATA 4 0x83fd9014 0x0040801d DATA 4 0x83fd9014 0x00008004

-# Write to CTL0 +/* Write to CTL0 */ DATA 4 0x83fd9000 0xb2a20000 -# Write to CTL1 +/* Write to CTL1 */ DATA 4 0x83fd9008 0xb2a20000 -# ESDMISC +/* ESDMISC */ DATA 4 0x83fd9010 0x000ad6d0 -#ESDCTL_ESDCDLYGD +/* ESDCTL_ESDCDLYGD */ DATA 4 0x83fd9034 0x90000000 DATA 4 0x83fd9014 0x00000000 diff --git a/board/genesi/mx51_efikamx/imximage_sb.cfg b/board/genesi/mx51_efikamx/imximage_sb.cfg index 26d259f..7ddd0b1 100644 --- a/board/genesi/mx51_efikamx/imximage_sb.cfg +++ b/board/genesi/mx51_efikamx/imximage_sb.cfg @@ -1,51 +1,55 @@ -# -# Copyright (C) 2009 Pegatron Corporation -# Copyright (C) 2010 Marek Vasut marek.vasut@gmail.com -# Copyright (C) 2009-2012 Genesi USA, Inc. -# -# BASED ON: imx51evk -# -# (C) Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage +/* + * Copyright (C) 2009 Pegatron Corporation + * Copyright (C) 2010 Marek Vasut marek.vasut@gmail.com + * Copyright (C) 2009-2012 Genesi USA, Inc. + * + * BASED ON: imx51evk + * + * (C) Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */

-# Boot Device : one of -# spi, sd (the board has no nand neither onenand) +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ BOOT_FROM spi

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register - -# DDR bus IOMUX PAD settings +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register +*/ +/* DDR bus IOMUX PAD settings */ DATA 4 0x73fa88a0 0x200 # GRP_INMODE1 DATA 4 0x73fa850c 0x20c5 # SDODT1 DATA 4 0x73fa8510 0x20c5 # SDODT0 @@ -62,22 +66,24 @@ DATA 4 0x73fa84b4 0xe5 # SDCKE1 DATA 4 0x73fa84cc 0xe5 # DRAM_CS0 DATA 4 0x73fa84d0 0xe4 # DRAM_CS1

-# Setting DDR for micron -# 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model -# CAS=3 BL=4 -# ESDCTL_ESDCTL0 +/* + * Setting DDR for micron + * 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model + * CAS=3 BL=4 + */ +/* ESDCTL_ESDCTL0 */ DATA 4 0x83fd9000 0x82a20000 -# ESDCTL_ESDCTL1 +/* ESDCTL_ESDCTL1 */ DATA 4 0x83fd9008 0x82a20000 -# ESDCTL_ESDMISC +/* ESDCTL_ESDMISC */ DATA 4 0x83fd9010 0xcaaaf6d0 -# ESDCTL_ESDCFG0 +/* ESDCTL_ESDCFG0 */ DATA 4 0x83fd9004 0x333574aa -# ESDCTL_ESDCFG1 +/* ESDCTL_ESDCFG1 */ DATA 4 0x83fd900c 0x333574aa

-# Init DRAM on CS0 -# ESDCTL_ESDSCR +/* Init DRAM on CS0 */ +/* ESDCTL_ESDSCR */ DATA 4 0x83fd9014 0x04008008 DATA 4 0x83fd9014 0x0000801a DATA 4 0x83fd9014 0x0000801b @@ -91,7 +97,7 @@ DATA 4 0x83fd9014 0x03808019 DATA 4 0x83fd9014 0x00408019 DATA 4 0x83fd9014 0x00008000

-# Init DRAM on CS1 +/* Init DRAM on CS1 */ DATA 4 0x83fd9014 0x0400800c DATA 4 0x83fd9014 0x0000801e DATA 4 0x83fd9014 0x0000801f @@ -105,12 +111,12 @@ DATA 4 0x83fd9014 0x0380801d DATA 4 0x83fd9014 0x0042801d DATA 4 0x83fd9014 0x00008004

-# Write to CTL0 +/* Write to CTL0 */ DATA 4 0x83fd9000 0xb2a20000 -# Write to CTL1 +/* Write to CTL1 */ DATA 4 0x83fd9008 0xb2a20000 -# ESDMISC +/* ESDMISC */ DATA 4 0x83fd9010 0xcaaaf6d0 -#ESDCTL_ESDCDLYGD +/* ESDCTL_ESDCDLYGD */ DATA 4 0x83fd9034 0x90000000 DATA 4 0x83fd9014 0x00000000 diff --git a/board/ttcontrol/vision2/imximage_hynix.cfg b/board/ttcontrol/vision2/imximage_hynix.cfg index ed531db..c1de94f 100644 --- a/board/ttcontrol/vision2/imximage_hynix.cfg +++ b/board/ttcontrol/vision2/imximage_hynix.cfg @@ -1,209 +1,228 @@ -# -# (C) Copyright 2009 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# (C) Copyright 2010 -# Klaus Steinhammer TTECH Control Gmbh kst@tttech.com -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# Boot Device : one of -# spi, nand, onenand, sd - +/* + * (C) Copyright 2009 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * (C) Copyright 2010 + * Klaus Steinhammer TTECH Control Gmbh kst@tttech.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* + * Boot Device : one of + * spi, nand, onenand, sd + */ BOOT_FROM spi

-# Device Configuration Data (DCD) -# -# Each entry must have the format: -# Addr-type Address Value -# -# where: -# Addr-type register length (1,2 or 4 bytes) -# Address absolute address of the register -# value value to be stored in the register - -####################### -### Disable WDOG ### -####################### +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* + * ####################### + * ### Disable WDOG ### + * ####################### + */ DATA 2 0x73f98000 0x30

-####################### -### SET DDR Clk ### -####################### - -# CCM: CBMCR - ddr_clk_sel: axi_b (133MHz) +/* + * ####################### + * ### SET DDR Clk ### + * ####################### + */ +/* CCM: CBMCR - ddr_clk_sel: axi_b (133MHz) */ DATA 4 0x73FD4018 0x000024C0

-# DOUBLE SPI CLK (13MHz->26 MHz Clock) +/* DOUBLE SPI CLK (13MHz->26 MHz Clock) */ DATA 4 0x73FD4038 0x2010241

-#IOMUXC_SW_PAD_CTL_PAD_CSPI1_MOSI HYS_ENABLE | DRV_MAX | SRE_FAST +/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_MOSI HYS_ENABLE | DRV_MAX | SRE_FAST */ DATA 4 0x73fa8600 0x00000107 -#IOMUXC_SW_PAD_CTL_PAD_CSPI1_MISO HYS_ENABLE | DRV_MAX | SRE_FAST +/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_MISO HYS_ENABLE | DRV_MAX | SRE_FAST */ DATA 4 0x73fa8604 0x00000107 -#IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS0 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST +/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS0 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST */ DATA 4 0x73fa8608 0x00000187 -#IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS1 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST +/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS1 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST */ DATA 4 0x73fa860c 0x00000187 -#IOMUXC_SW_PAD_CTL_PAD_CSPI1_SCLK HYS_ENABLE | DRV_MAX | SRE_FAST +/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SCLK HYS_ENABLE | DRV_MAX | SRE_FAST */ DATA 4 0x73fa8614 0x00000107 -#IOMUXC_SW_PAD_CTL_PAD_DI1_PIN11 HYS_ENABLE | DRV_MAX | SRE_FAST (CSPI1_SS2) +/* IOMUXC_SW_PAD_CTL_PAD_DI1_PIN11 HYS_ENABLE | DRV_MAX | SRE_FAST (CSPI1_SS2) */ DATA 4 0x73fa86a8 0x00000187

-####################### -### Settings IOMUXC ### -####################### - -# DDR IOMUX configuration -# Control, Data, Address pads are in their default state: HIGH DS, FAST SR. -# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK MAX DS +/* + * ####################### + * ### Settings IOMUXC ### + * ####################### + */ +/* + * DDR IOMUX configuration + * Control, Data, Address pads are in their default state: HIGH DS, FAST SR. + * IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK MAX DS + */ DATA 4 0x73fa84b8 0x000000e7 -# PVTC MAX (at GPC, PGR reg) -#DATA 4 0x73FD8004 0x1fc00000 +/* PVTC MAX (at GPC, PGR reg) */ +/* DATA 4 0x73FD8004 0x1fc00000 */

-#DQM0 DS high slew rate slow +/* DQM0 DS high slew rate slow */ DATA 4 0x73fa84d4 0x000000e4 -#DQM1 DS high slew rate slow +/* DQM1 DS high slew rate slow */ DATA 4 0x73fa84d8 0x000000e4 -#DQM2 DS high slew rate slow +/* DQM2 DS high slew rate slow */ DATA 4 0x73fa84dc 0x000000e4 -#DQM3 DS high slew rate slow +/* DQM3 DS high slew rate slow */ DATA 4 0x73fa84e0 0x000000e4

-#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 DS high & SLEW slow +/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 DS high & SLEW slow */ DATA 4 0x73fa84bc 0x000000c4 -#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 DS high & SLEW slow +/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 DS high & SLEW slow */ DATA 4 0x73fa84c0 0x000000c4 -#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2 DS high & SLEW slow +/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2 DS high & SLEW slow */ DATA 4 0x73fa84c4 0x000000c4 -#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3 DS high & SLEW slow +/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3 DS high & SLEW slow */ DATA 4 0x73fa84c8 0x000000c4

-#DRAM_DATA B0 +/* DRAM_DATA B0 */ DATA 4 0x73fa88a4 0x00000004 -#DRAM_DATA B1 +/* DRAM_DATA B1 */ DATA 4 0x73fa88ac 0x00000004 -#DRAM_DATA B2 +/* DRAM_DATA B2 */ DATA 4 0x73fa88b8 0x00000004 -#DRAM_DATA B3 +/* DRAM_DATA B3 */ DATA 4 0x73fa882c 0x00000004

-#DRAM_DATA B0 slew rate +/* DRAM_DATA B0 slew rate */ DATA 4 0x73fa8878 0x00000000 -#DRAM_DATA B1 slew rate +/* DRAM_DATA B1 slew rate */ DATA 4 0x73fa8880 0x00000000 -#DRAM_DATA B2 slew rate +/* DRAM_DATA B2 slew rate */ DATA 4 0x73fa888c 0x00000000 -#DRAM_DATA B3 slew rate +/* DRAM_DATA B3 slew rate */ DATA 4 0x73fa889c 0x00000000

-####################### -### Configure SDRAM ### -####################### +/* + * ####################### + * ### Configure SDRAM ### + * ####################### + */

-# Configure CS0 -####################### +/* Configure CS0 */ +/* ####################### */

-# ESDCTL0: Enable controller +/* ESDCTL0: Enable controller */ DATA 4 0x83fd9000 0x83220000

-# Init DRAM on CS0 -# ESDSCR: Precharge command +/* Init DRAM on CS0 / +/* ESDSCR: Precharge command */ DATA 4 0x83fd9014 0x04008008 -# ESDSCR: Refresh command +/* ESDSCR: Refresh command */ DATA 4 0x83fd9014 0x00008010 -# ESDSCR: Refresh command +/* ESDSCR: Refresh command */ DATA 4 0x83fd9014 0x00008010 -# ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) +/* ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) */ DATA 4 0x83fd9014 0x00338018 -# ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) +/* ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) */ DATA 4 0x83fd9014 0x0020801a -# ESDSCR +/* ESDSCR */ DATA 4 0x83fd9014 0x00008000

-# ESDSCR: EMR with full Drive strength -#DATA 4 0x83fd9014 0x0000801a +/* ESDSCR: EMR with full Drive strength */ +/* DATA 4 0x83fd9014 0x0000801a */

-# ESDCTL0: 14 ROW, 10 COL, 32Bit, SREF=8 +/* ESDCTL0: 14 ROW, 10 COL, 32Bit, SREF=8 */ DATA 4 0x83fd9000 0xC3220000

-# ESDCFG0: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks -# tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks -#DATA 4 0x83fd9004 0xC33574AA - -#micron mDDR -# ESDCFG0: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks -# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks -#DATA 4 0x83FD9004 0x101564a8 - -#hynix mDDR -# ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks -# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks +/* + * ESDCFG0: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks + * tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks + * DATA 4 0x83fd9004 0xC33574AA + */ +/* + * micron mDDR + * ESDCFG0: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks + * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks + * DATA 4 0x83FD9004 0x101564a8 + */ +/* + * hynix mDDR + * ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks + * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks + */ DATA 4 0x83FD9004 0x704564a8

-# ESDMISC: AP=10, Bank interleaving on, MIF3 en, RALAT=2 +/* ESDMISC: AP=10, Bank interleaving on, MIF3 en, RALAT=2 */ DATA 4 0x83fd9010 0x000a1700

-# Configure CS1 -####################### +/* Configure CS1 */ +/* ####################### */

-# ESDCTL1: Enable controller +/* ESDCTL1: Enable controller */ DATA 4 0x83fd9008 0x83220000

-# Init DRAM on CS1 -# ESDSCR: Precharge command +/* Init DRAM on CS1 */ +/* ESDSCR: Precharge command */ DATA 4 0x83fd9014 0x0400800c -# ESDSCR: Refresh command +/* ESDSCR: Refresh command */ DATA 4 0x83fd9014 0x00008014 -# ESDSCR: Refresh command +/* ESDSCR: Refresh command */ DATA 4 0x83fd9014 0x00008014 -# ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) +/* ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) */ DATA 4 0x83fd9014 0x0033801c -# ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) +/* ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) */ DATA 4 0x83fd9014 0x0020801e -# ESDSCR +/* ESDSCR */ DATA 4 0x83fd9014 0x00008004

-# ESDCTL1: 14 ROW, 10 COL, 32Bit, SREF=8 +/* ESDCTL1: 14 ROW, 10 COL, 32Bit, SREF=8 */ DATA 4 0x83fd9008 0xC3220000 - -# ESDCFG1: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks -# tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks -#DATA 4 0x83fd900c 0xC33574AA - -#micron mDDR -# ESDCFG1: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks -# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks -#DATA 4 0x83FD900C 0x101564a8 - -#hynix mDDR -# ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks -# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks +/* + * ESDCFG1: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks + * tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks + * DATA 4 0x83fd900c 0xC33574AA + */ +/* + * micron mDDR + * ESDCFG1: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks + * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks + * DATA 4 0x83FD900C 0x101564a8 + */ +/* + * hynix mDDR + * ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks + * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks + */ DATA 4 0x83FD900C 0x704564a8

-# ESDSCR (mDRAM configuration finished) +/* ESDSCR (mDRAM configuration finished) */ DATA 4 0x83FD9014 0x00000004

-# ESDSCR - clear "configuration request" bit +/* ESDSCR - clear "configuration request" bit */ DATA 4 0x83fd9014 0x00000000

-- 1.7.9.5

Reply

Troy Kisky

18 Jan 18 Jan

2:49 a.m.

New subject: [U-Boot] [PATCH V2 1/1] imximage.cfg: run files through C preprocessor

The '#' used as comments in the files cause the preprocessor trouble, so change to /* */.

Signed-off-by: Troy Kisky troy.kisky@boundarydevices.com --- v2: moved the mkimage call to arch/arm/imx-common Makefile updated spl/Makefile as well added board/woodburn/imximage.cfg conversion --- .gitignore | 1 + Makefile | 8 +- arch/arm/cpu/arm926ejs/config.mk | 2 +- arch/arm/cpu/armv7/config.mk | 2 +- arch/arm/imx-common/Makefile | 13 ++ board/esg/ima3-mx53/imximage.cfg | 120 ++++++----- board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg | 90 ++++---- board/freescale/mx25pdk/imximage.cfg | 77 +++---- board/freescale/mx51evk/imximage.cfg | 114 +++++----- board/freescale/mx53ard/imximage_dd3.cfg | 83 ++++---- board/freescale/mx53evk/imximage.cfg | 86 ++++---- board/freescale/mx53loco/imximage.cfg | 83 ++++---- board/freescale/mx53smd/imximage.cfg | 83 ++++---- board/freescale/mx6qarm2/imximage.cfg | 88 ++++---- board/freescale/mx6qsabreauto/imximage.cfg | 82 +++---- board/genesi/mx51_efikamx/imximage_mx.cfg | 132 ++++++------ board/genesi/mx51_efikamx/imximage_sb.cfg | 126 +++++------ board/ttcontrol/vision2/imximage_hynix.cfg | 295 ++++++++++++++------------ board/woodburn/imximage.cfg | 2 +- spl/Makefile | 7 +- 20 files changed, 791 insertions(+), 703 deletions(-)

diff --git a/.gitignore b/.gitignore index a163728..e40eb7b 100644 --- a/.gitignore +++ b/.gitignore @@ -15,6 +15,7 @@ *.swp *.patch *.bin +*.cfgtmp

# Build tree /build-* diff --git a/Makefile b/Makefile index 3305e8c..7ba7766 100644 --- a/Makefile +++ b/Makefile @@ -467,9 +467,8 @@ $(obj)u-boot.img: $(obj)u-boot.bin sed -e 's/"[ ]*$$/ for $(BOARD) board"/') \ -d $< $@

-$(obj)u-boot.imx: $(obj)u-boot.bin - $(obj)tools/mkimage -n $(CONFIG_IMX_CONFIG) -T imximage \ - -e $(CONFIG_SYS_TEXT_BASE) -d $< $@ +$(OBJTREE)/u-boot.imx : $(obj)u-boot.bin $(SUBDIR_TOOLS) depend + $(MAKE) -C $(SRCTREE)/arch/arm/imx-common $@

$(obj)u-boot.kwb: $(obj)u-boot.bin $(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T kwbimage \ @@ -843,7 +842,8 @@ clean: @$(MAKE) -s -C doc/DocBook/ cleandocs @find $(OBJTREE) -type f \ ( -name 'core' -o -name '*.bak' -o -name '*~' -o -name '*.su' \ - -o -name '*.o' -o -name '*.a' -o -name '*.exe' ) -print \ + -o -name '*.o' -o -name '*.a' -o -name '*.exe' \ + -o -name '*.cfgtmp' ) -print \ | xargs rm -f

# Removes everything not needed for testing u-boot diff --git a/arch/arm/cpu/arm926ejs/config.mk b/arch/arm/cpu/arm926ejs/config.mk index 6a3a1bb..47f24f5 100644 --- a/arch/arm/cpu/arm926ejs/config.mk +++ b/arch/arm/cpu/arm926ejs/config.mk @@ -34,6 +34,6 @@ PLATFORM_RELFLAGS += $(PF_RELFLAGS_SLB_AT)

ifneq ($(CONFIG_IMX_CONFIG),)

-ALL-y += $(obj)u-boot.imx +ALL-y += $(OBJTREE)/u-boot.imx

endif diff --git a/arch/arm/cpu/armv7/config.mk b/arch/arm/cpu/armv7/config.mk index 9c3e2f3..350e946 100644 --- a/arch/arm/cpu/armv7/config.mk +++ b/arch/arm/cpu/armv7/config.mk @@ -40,5 +40,5 @@ PF_NO_UNALIGNED := $(call cc-option, -mno-unaligned-access,) PLATFORM_NO_UNALIGNED := $(PF_NO_UNALIGNED)

ifneq ($(CONFIG_IMX_CONFIG),) -ALL-y += $(obj)u-boot.imx +ALL-y += $(OBJTREE)/u-boot.imx endif diff --git a/arch/arm/imx-common/Makefile b/arch/arm/imx-common/Makefile index b3e608e..6309fcd 100644 --- a/arch/arm/imx-common/Makefile +++ b/arch/arm/imx-common/Makefile @@ -42,6 +42,19 @@ all: $(obj).depend $(LIB) $(LIB): $(OBJS) $(call cmd_link_o_target, $(OBJS))

+$(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp: $(OBJTREE)/%.cfgtmp : $(SRCTREE)/% + mkdir -p $(dir $@) + $(CC) -E -x c $< $(CPPFLAGS) -o $@ + +$(OBJTREE)/u-boot.imx: $(OBJTREE)/u-boot.bin $(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp + $(OBJTREE)/tools/mkimage -n $(filter-out %.bin,$^) -T imximage \ + -e $(CONFIG_SYS_TEXT_BASE) -d $< $@ + +$(OBJTREE)/SPL: $(OBJTREE)/spl/u-boot-spl.bin $(OBJTREE)/$(patsubst "%",%,$(CONFIG_IMX_CONFIG)).cfgtmp + $(OBJTREE)/tools/mkimage -n $(filter-out %.bin,$^) -T imximage \ + -e $(CONFIG_SPL_TEXT_BASE) -d $< $@ + + #########################################################################

# defines $(obj).depend target diff --git a/board/esg/ima3-mx53/imximage.cfg b/board/esg/ima3-mx53/imximage.cfg index fa6b42d..fce7492 100644 --- a/board/esg/ima3-mx53/imximage.cfg +++ b/board/esg/ima3-mx53/imximage.cfg @@ -1,50 +1,52 @@ -# -# (C) Copyright 2012 -# Stefano Babic DENX Software Engineering sbabic@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not write to the Free Software -# Foundation Inc. 51 Franklin Street Fifth Floor Boston, -# MA 02110-1301 USA -# -# Refer docs/README.imxmage for more details about how-to configure -# and create imximage boot image -# -# The syntax is taken as close as possible with the kwbimage - -# image version +/* + * (C) Copyright 2012 + * Stefano Babic DENX Software Engineering sbabic@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not write to the Free Software + * Foundation Inc. 51 Franklin Street Fifth Floor Boston, + * MA 02110-1301 USA + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */