[U-Boot] [PATCH 0/3] pmic:pfuze support buck regulator mode switch
This patch set is to support buck regulator can working in different switching modes.
To improve system efficiency the buck regulators can operate in different switching modes.
patch 1/3 is to add related bit definitions and registers. patch 2/3 is to implement the switching mode init function. patch 3/3 is to add related mode init function in board code.
mx6slevk board is not included in this patch set, since power and i2c interface are not implemented for it. Future patch will cover this to add PAD setting, power_init_board and etc.
Peng Fan (3): pmic:pfuz100 add switch mode and more registers pmic:pfuze implement pmic_mode_init imx:mx6 set normal APS and standby PFM mode
board/freescale/common/pfuze.c | 36 ++++++++++++++++++ board/freescale/common/pfuze.h | 1 + board/freescale/mx6qsabreauto/mx6qsabreauto.c | 5 +++ board/freescale/mx6sabresd/mx6sabresd.c | 6 ++- board/freescale/mx6sxsabresd/mx6sxsabresd.c | 6 ++- include/power/pfuze100_pmic.h | 53 +++++++++++++++++++++++++++ 6 files changed, 105 insertions(+), 2 deletions(-)
Add more pfuze register offset. And switch mode definition.
Signed-off-by: Peng Fan Peng.Fan@freescale.com --- include/power/pfuze100_pmic.h | 53 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 53 insertions(+)
diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h index 1118489..7474afb 100644 --- a/include/power/pfuze100_pmic.h +++ b/include/power/pfuze100_pmic.h @@ -16,14 +16,34 @@ enum {
PFUZE100_SW1ABVOL = 0x20, PFUZE100_SW1ABSTBY = 0x21, + PFUZE100_SW1ABOFF = 0x22, + PFUZE100_SW1ABMODE = 0x23, PUZE_100_SW1ABCONF = 0x24, PFUZE100_SW1CVOL = 0x2e, PFUZE100_SW1CSTBY = 0x2f, + PFUZE100_SW1COFF = 0x30, + PFUZE100_SW1CMODE = 0x31, PFUZE100_SW1CCONF = 0x32, PFUZE100_SW2VOL = 0x35, + PFUZE100_SW2STBY = 0x36, + PFUZE100_SW2OFF = 0x37, + PFUZE100_SW2MODE = 0x38, + PFUZE100_SW2CONF = 0x39, PFUZE100_SW3AVOL = 0x3c, + PFUZE100_SW3ASTBY = 0x3D, + PFUZE100_SW3AOFF = 0x3E, + PFUZE100_SW3AMODE = 0x3F, + PFUZE100_SW3ACONF = 0x40, PFUZE100_SW3BVOL = 0x43, + PFUZE100_SW3BSTBY = 0x44, + PFUZE100_SW3BOFF = 0x45, + PFUZE100_SW3BMODE = 0x46, + PFUZE100_SW3BCONF = 0x47, PFUZE100_SW4VOL = 0x4a, + PFUZE100_SW4STBY = 0x4b, + PFUZE100_SW4OFF = 0x4c, + PFUZE100_SW4MODE = 0x4d, + PFUZE100_SW4CONF = 0x4e, PFUZE100_SWBSTCON1 = 0x66, PFUZE100_VREFDDRCON = 0x6a, PFUZE100_VSNVSVOL = 0x6b, @@ -177,5 +197,38 @@ enum { #define SWBST_MODE_AUTO (2 << 2) #define SWBST_MODE_APS (2 << 3)
+/* + * Regulator Mode Control + * + * OFF: The regulator is switched off and the output voltage is discharged. + * PFM: In this mode, the regulator is always in PFM mode, which is useful + * at light loads for optimized efficiency. + * PWM: In this mode, the regulator is always in PWM mode operation + * regardless of load conditions. + * APS: In this mode, the regulator moves automatically between pulse + * skipping mode and PWM mode depending on load conditions. + * + * SWxMODE[3:0] + * Normal Mode | Standby Mode | value + * OFF OFF 0x0 + * PWM OFF 0x1 + * PFM OFF 0x3 + * APS OFF 0x4 + * PWM PWM 0x5 + * PWM APS 0x6 + * APS APS 0x8 + * APS PFM 0xc + * PWM PFM 0xd + */ +#define OFF_OFF 0x0 +#define PWM_OFF 0x1 +#define PFM_OFF 0x3 +#define APS_OFF 0x4 +#define PWM_PWM 0x5 +#define PWM_APS 0x6 +#define APS_APS 0x8 +#define APS_PFM 0xc +#define PWM_PFM 0xd + int power_pfuze100_init(unsigned char bus); #endif
This patch is to implement pmic_mode_init function, and add prototype in header file.
This function is to set switching mode for pmic buck regulators to improve system efficiency.
Mode: OFF: The regulator is switched off and the output voltage is discharged. PFM: In this mode, the regulator is always in PFM mode, which is useful at light loads for optimized efficiency. PWM: In this mode, the regulator is always in PWM mode operation regardless of load conditions. APS: In this mode, the regulator moves automatically between pulse skipping mode and PWM mode depending on load conditions.
Signed-off-by: Peng Fan Peng.Fan@freescale.com --- board/freescale/common/pfuze.c | 36 ++++++++++++++++++++++++++++++++++++ board/freescale/common/pfuze.h | 1 + 2 files changed, 37 insertions(+)
diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c index 2cd1794..74df69c 100644 --- a/board/freescale/common/pfuze.c +++ b/board/freescale/common/pfuze.c @@ -8,6 +8,42 @@ #include <power/pmic.h> #include <power/pfuze100_pmic.h>
+int pfuze_mode_init(struct pmic *p, u32 mode) +{ + unsigned char offset, i, switch_num; + u32 id, ret; + + pmic_reg_read(p, PFUZE100_DEVICEID, &id); + id = id & 0xf; + + if (id == 0) { + switch_num = 6; + offset = PFUZE100_SW1CMODE; + } else if (id == 1) { + switch_num = 4; + offset = PFUZE100_SW2MODE; + } else { + printf("Not supported, id=%d\n", id); + return -1; + } + + ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode); + if (ret < 0) { + printf("Set SW1AB mode error!\n"); + return ret; + } + + for (i = 0; i < switch_num - 1; i++) { + ret = pmic_reg_write(p, offset + i * 7, mode); + if (ret < 0) { + printf("Set switch%x mode error!\n", offset + i * 7); + return ret; + } + } + + return ret; +} + struct pmic *pfuze_common_init(unsigned char i2cbus) { struct pmic *p; diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h index 7a4126c..53cfc99 100644 --- a/board/freescale/common/pfuze.h +++ b/board/freescale/common/pfuze.h @@ -8,5 +8,6 @@ #define __PFUZE_BOARD_HELPER__
struct pmic *pfuze_common_init(unsigned char i2cbus); +int pfuze_mode_init(struct pmic *p, u32 mode);
#endif
Hello Peg,
On 01/08/2015 02:00 PM, Peng Fan wrote:
This patch is to implement pmic_mode_init function, and add prototype in header file.
This function is to set switching mode for pmic buck regulators to improve system efficiency.
Mode: OFF: The regulator is switched off and the output voltage is discharged. PFM: In this mode, the regulator is always in PFM mode, which is useful at light loads for optimized efficiency. PWM: In this mode, the regulator is always in PWM mode operation regardless of load conditions. APS: In this mode, the regulator moves automatically between pulse skipping mode and PWM mode depending on load conditions.
Signed-off-by: Peng Fan Peng.Fan@freescale.com
board/freescale/common/pfuze.c | 36 ++++++++++++++++++++++++++++++++++++ board/freescale/common/pfuze.h | 1 + 2 files changed, 37 insertions(+)
diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c index 2cd1794..74df69c 100644 --- a/board/freescale/common/pfuze.c +++ b/board/freescale/common/pfuze.c @@ -8,6 +8,42 @@ #include <power/pmic.h> #include <power/pfuze100_pmic.h>
In this function, you set the same operating mode to the all switching regulators, so this will be done for the all boards which will use this pmic call. I assume that this is what you want, if not, then maybe adding the regulator number as an argument, could make it more flexible, for the other configurations. So what do you think about this?
+int pfuze_mode_init(struct pmic *p, u32 mode) +{
- unsigned char offset, i, switch_num;
- u32 id, ret;
- pmic_reg_read(p, PFUZE100_DEVICEID, &id);
- id = id & 0xf;
- if (id == 0) {
switch_num = 6;offset = PFUZE100_SW1CMODE;- } else if (id == 1) {
switch_num = 4;offset = PFUZE100_SW2MODE;- } else {
printf("Not supported, id=%d\n", id);return -1;- }
- ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
- if (ret < 0) {
printf("Set SW1AB mode error!\n");return ret;- }
- for (i = 0; i < switch_num - 1; i++) {
ret = pmic_reg_write(p, offset + i * 7, mode);if (ret < 0) {printf("Set switch%x mode error!\n", offset + i * 7);return ret;}- }
- return ret;
+}
- struct pmic *pfuze_common_init(unsigned char i2cbus) { struct pmic *p;
diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h index 7a4126c..53cfc99 100644 --- a/board/freescale/common/pfuze.h +++ b/board/freescale/common/pfuze.h @@ -8,5 +8,6 @@ #define __PFUZE_BOARD_HELPER__
struct pmic *pfuze_common_init(unsigned char i2cbus); +int pfuze_mode_init(struct pmic *p, u32 mode);
#endif
If you don't need such feature, then you have my ACK.
For the patchset: Acked-by: Przemyslaw Marczak p.marczak@samsung.com
Best regards,
Hi, Przemyslaw
On 1/15/2015 5:00 PM, Przemyslaw Marczak wrote:
Hello Peg,
On 01/08/2015 02:00 PM, Peng Fan wrote:
This patch is to implement pmic_mode_init function, and add prototype in header file.
This function is to set switching mode for pmic buck regulators to improve system efficiency.
Mode: OFF: The regulator is switched off and the output voltage is discharged. PFM: In this mode, the regulator is always in PFM mode, which is useful at light loads for optimized efficiency. PWM: In this mode, the regulator is always in PWM mode operation regardless of load conditions. APS: In this mode, the regulator moves automatically between pulse skipping mode and PWM mode depending on load conditions.
Signed-off-by: Peng Fan Peng.Fan@freescale.com
board/freescale/common/pfuze.c | 36 ++++++++++++++++++++++++++++++++++++ board/freescale/common/pfuze.h | 1 + 2 files changed, 37 insertions(+)
diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c index 2cd1794..74df69c 100644 --- a/board/freescale/common/pfuze.c +++ b/board/freescale/common/pfuze.c @@ -8,6 +8,42 @@ #include <power/pmic.h> #include <power/pfuze100_pmic.h>
In this function, you set the same operating mode to the all switching regulators, so this will be done for the all boards which will use this pmic call. I assume that this is what you want, if not, then maybe adding the regulator number as an argument, could make it more flexible, for the other configurations. So what do you think about this?
This is a good suggestion that configure each regulator with it's own requirement. I'll add a new function pfuze_regulator_mode_set to set each regulator's mode according input parameter, and also keep pfuze_mode_init to configure all regulators. I'll sent out v2 patch soon.
+int pfuze_mode_init(struct pmic *p, u32 mode) +{
- unsigned char offset, i, switch_num;
- u32 id, ret;
- pmic_reg_read(p, PFUZE100_DEVICEID, &id);
- id = id & 0xf;
- if (id == 0) {
switch_num = 6;offset = PFUZE100_SW1CMODE;- } else if (id == 1) {
switch_num = 4;offset = PFUZE100_SW2MODE;- } else {
printf("Not supported, id=%d\n", id);return -1;- }
- ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
- if (ret < 0) {
printf("Set SW1AB mode error!\n");return ret;- }
- for (i = 0; i < switch_num - 1; i++) {
ret = pmic_reg_write(p, offset + i * 7, mode);if (ret < 0) {printf("Set switch%x mode error!\n", offset + i * 7);return ret;}- }
- return ret;
+}
- struct pmic *pfuze_common_init(unsigned char i2cbus) { struct pmic *p;
diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h index 7a4126c..53cfc99 100644 --- a/board/freescale/common/pfuze.h +++ b/board/freescale/common/pfuze.h @@ -8,5 +8,6 @@ #define __PFUZE_BOARD_HELPER__
struct pmic *pfuze_common_init(unsigned char i2cbus); +int pfuze_mode_init(struct pmic *p, u32 mode);
#endif
If you don't need such feature, then you have my ACK.
For the patchset: Acked-by: Przemyslaw Marczak p.marczak@samsung.com
Thanks, Peng.
Hi Stefano,
On 1/15/2015 5:00 PM, Przemyslaw Marczak wrote:
Hello Peg,
On 01/08/2015 02:00 PM, Peng Fan wrote:
This patch is to implement pmic_mode_init function, and add prototype in header file.
This function is to set switching mode for pmic buck regulators to improve system efficiency.
Mode: OFF: The regulator is switched off and the output voltage is discharged. PFM: In this mode, the regulator is always in PFM mode, which is useful at light loads for optimized efficiency. PWM: In this mode, the regulator is always in PWM mode operation regardless of load conditions. APS: In this mode, the regulator moves automatically between pulse skipping mode and PWM mode depending on load conditions.
Signed-off-by: Peng Fan Peng.Fan@freescale.com
board/freescale/common/pfuze.c | 36 ++++++++++++++++++++++++++++++++++++ board/freescale/common/pfuze.h | 1 + 2 files changed, 37 insertions(+)
diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c index 2cd1794..74df69c 100644 --- a/board/freescale/common/pfuze.c +++ b/board/freescale/common/pfuze.c @@ -8,6 +8,42 @@ #include <power/pmic.h> #include <power/pfuze100_pmic.h>
In this function, you set the same operating mode to the all switching regulators, so this will be done for the all boards which will use this pmic call. I assume that this is what you want, if not, then maybe adding the regulator number as an argument, could make it more flexible, for the other configurations. So what do you think about this?
+int pfuze_mode_init(struct pmic *p, u32 mode) +{
- unsigned char offset, i, switch_num;
- u32 id, ret;
- pmic_reg_read(p, PFUZE100_DEVICEID, &id);
- id = id & 0xf;
- if (id == 0) {
switch_num = 6;offset = PFUZE100_SW1CMODE;- } else if (id == 1) {
switch_num = 4;offset = PFUZE100_SW2MODE;- } else {
printf("Not supported, id=%d\n", id);return -1;- }
- ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
- if (ret < 0) {
printf("Set SW1AB mode error!\n");return ret;- }
- for (i = 0; i < switch_num - 1; i++) {
ret = pmic_reg_write(p, offset + i * 7, mode);if (ret < 0) {printf("Set switch%x mode error!\n", offset + i * 7);return ret;}- }
- return ret;
+}
- struct pmic *pfuze_common_init(unsigned char i2cbus) { struct pmic *p;
diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h index 7a4126c..53cfc99 100644 --- a/board/freescale/common/pfuze.h +++ b/board/freescale/common/pfuze.h @@ -8,5 +8,6 @@ #define __PFUZE_BOARD_HELPER__
struct pmic *pfuze_common_init(unsigned char i2cbus); +int pfuze_mode_init(struct pmic *p, u32 mode);
#endif
If you don't need such feature, then you have my ACK.
For the patchset: Acked-by: Przemyslaw Marczak p.marczak@samsung.com
Since this patch set is fine for the boards, and the new feature can be done in future patch, please review the ldo bypass patches based on this patch set. That v2 patch set is discarded.
Best regards,
Thanks, Peng.
To normal mode, use APS switching mode. To standy mode, use PFM switching mode.
Signed-off-by: Peng Fan Peng.Fan@freescale.com --- board/freescale/mx6qsabreauto/mx6qsabreauto.c | 5 +++++ board/freescale/mx6sabresd/mx6sabresd.c | 6 +++++- board/freescale/mx6sxsabresd/mx6sxsabresd.c | 6 +++++- 3 files changed, 15 insertions(+), 2 deletions(-)
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c index 59387ff..b29ff2b 100644 --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c @@ -515,11 +515,16 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs) int power_init_board(void) { struct pmic *p; + unsigned int ret;
p = pfuze_common_init(I2C_PMIC); if (!p) return -ENODEV;
+ ret = pfuze_mode_init(p, APS_PFM); + if (ret < 0) + return -EIO; + return 0; }
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 2f7198d..59544d9 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -631,12 +631,16 @@ int board_init(void) int power_init_board(void) { struct pmic *p; - unsigned int reg; + unsigned int reg, ret;
p = pfuze_common_init(I2C_PMIC); if (!p) return -ENODEV;
+ ret = pfuze_mode_init(p, APS_PFM); + if (ret < 0) + return -EIO; + /* Increase VGEN3 from 2.5 to 2.8V */ pmic_reg_read(p, PFUZE100_VGEN3VOL, ®); reg &= ~LDO_VOL_MASK; diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c index 5cc58ac..fbf3337 100644 --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c @@ -199,12 +199,16 @@ static struct i2c_pads_info i2c_pad_info1 = { int power_init_board(void) { struct pmic *p; - unsigned int reg; + unsigned int reg, ret;
p = pfuze_common_init(I2C_PMIC); if (!p) return -ENODEV;
+ ret = pfuze_mode_init(p, APS_PFM); + if (ret < 0) + return -EIO; + /* Enable power of VGEN5 3V3, needed for SD3 */ pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); reg &= ~LDO_VOL_MASK;
participants (3)
-
Peng Fan -
Peng Fan -
Przemyslaw Marczak