TWR-P1025 Specification: ----------------------- Memory subsystem: 512MB DDR3 (on board DDR) 64Mbyte 16bit NOR flash One microSD Card slot

Ethernet: eTSEC1: Connected to Atheros AR8035 GETH PHY eTSEC3: Connected to Atheros AR8035 GETH PHY

UART: Two UARTs are routed to the FDTI dual USB to RS232 convertor

USB: Two USB2.0 Type A ports

I2C: AT24C01B 1K Board EEPROM (8 bit address)

QUICC Engine: Connected to DP83849i PHY supply two 10/100M ethernet ports QE UART for RS485 or RS232

PCIE: One mini-PCIE slot

Signed-off-by: Michael Johnston michael.johnston@freescale.com Signed-off-by: Xie Xiaobo X.Xie@freescale.com --- arch/powerpc/include/asm/immap_85xx.h | 2 + board/freescale/p1_twr/Makefile | 52 +++ board/freescale/p1_twr/ddr.c | 71 ++++ board/freescale/p1_twr/law.c | 32 ++ board/freescale/p1_twr/p1_twr.c | 333 ++++++++++++++++ board/freescale/p1_twr/tlb.c | 92 +++++ boards.cfg | 2 + include/configs/p1_twr.h | 694 ++++++++++++++++++++++++++++++++++ 8 files changed, 1278 insertions(+) create mode 100644 board/freescale/p1_twr/Makefile create mode 100644 board/freescale/p1_twr/ddr.c create mode 100644 board/freescale/p1_twr/law.c create mode 100644 board/freescale/p1_twr/p1_twr.c create mode 100644 board/freescale/p1_twr/tlb.c create mode 100644 include/configs/p1_twr.h

diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 296b549..1730827 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -2164,6 +2164,8 @@ typedef struct ccsr_gur { u32 porbmsr; /* POR boot mode status */ #define MPC85xx_PORBMSR_HA 0x00070000 #define MPC85xx_PORBMSR_HA_SHIFT 16 +#define MPC85xx_PORBMSR_ROMLOC 0x0f000000 +#define MPC85xx_PORBMSR_ROMLOC_SHIFT 24 u32 porimpscr; /* POR I/O impedance status & control */ u32 pordevsr; /* POR I/O device status regsiter */ #if defined(CONFIG_P1017) || defined(CONFIG_P1023) diff --git a/board/freescale/p1_twr/Makefile b/board/freescale/p1_twr/Makefile new file mode 100644 index 0000000..8056af8 --- /dev/null +++ b/board/freescale/p1_twr/Makefile @@ -0,0 +1,52 @@ +# +# Copyright 2010-2011 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1_twr/ddr.c b/board/freescale/p1_twr/ddr.c new file mode 100644 index 0000000..b67ec1b --- /dev/null +++ b/board/freescale/p1_twr/ddr.c @@ -0,0 +1,71 @@ +/* + * Copyright 2010-2011, 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/processor.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> +#include <asm/io.h> +#include <asm/fsl_law.h> + +/* Fixed sdram init -- doesn't use serial presence detect. */ +phys_size_t fixed_sdram(void) +{ + sys_info_t sysinfo; + char buf[32]; + size_t ddr_size; + fsl_ddr_cfg_regs_t ddr_cfg_regs = { + .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, + .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, + .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, +#if CONFIG_CHIP_SELECTS_PER_CTRL > 1 + .cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS, + .cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG, + .cs[1].config_2 = CONFIG_SYS_DDR_CS1_CONFIG_2, +#endif + .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3, + .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0, + .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1, + .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2, + .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL, + .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2, + .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1, + .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2, + .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, + .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL, + .ddr_data_init = CONFIG_SYS_DDR_DATA_INIT, + .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL, + .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, + .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, + .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, + .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, + .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL, + .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL, + .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR, + .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, + .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 + }; + + get_sys_info(&sysinfo); + printf("Configuring DDR for %s MT/s data rate\n", + strmhz(buf, sysinfo.freqDDRBus)); + + ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; + + fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0); + + if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, + ddr_size, LAW_TRGT_IF_DDR_1) < 0) { + printf("ERROR setting Local Access Windows for DDR\n"); + return 0; + }; + + return ddr_size; +} diff --git a/board/freescale/p1_twr/law.c b/board/freescale/p1_twr/law.c new file mode 100644 index 0000000..cfefbb0 --- /dev/null +++ b/board/freescale/p1_twr/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_SSD_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC) +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1_twr/p1_twr.c b/board/freescale/p1_twr/p1_twr.c new file mode 100644 index 0000000..953b214 --- /dev/null +++ b/board/freescale/p1_twr/p1_twr.c @@ -0,0 +1,333 @@ +/* + * Copyright 2010-2011, 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <hwconfig.h> +#include <pci.h> +#include <i2c.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/io.h> +#include <asm/fsl_law.h> +#include <asm/fsl_lbc.h> +#include <asm/mp.h> +#include <miiphy.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <fsl_mdio.h> +#include <tsec.h> +#include <ioports.h> +#include <asm/fsl_serdes.h> +#include <netdev.h> + +#define SYSCLK_64 64000000 +#define SYSCLK_66 66666666 + +unsigned long get_board_sys_clk(ulong dummy) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + par_io_t *par_io = (par_io_t *) &(gur->qe_par_io); + unsigned int cpdat_val = 0; + + /* Set-up up pin muxing based on board switch settings */ + cpdat_val = par_io[1].cpdat; + + /* Check switch setting for SYSCLK select (PB3) */ + if (cpdat_val & 0x10000000) + return SYSCLK_64; + else + return SYSCLK_66; + + return 0; +} + +#ifdef CONFIG_QE + +#define PCA_IOPORT_I2C_ADDR 0x23 +#define PCA_IOPORT_OUTPUT_CMD 0x2 +#define PCA_IOPORT_CFG_CMD 0x6 + +const qe_iop_conf_t qe_iop_conf_tab[] = { + +#ifdef CONFIG_TWR_P1025 + /* GPIO */ + {1, 0, 1, 0, 0}, + {1, 18, 1, 0, 0}, + + /* GPIO for switch options */ + {1, 2, 2, 0, 0}, /* PROFIBUS_MODE_SEL */ + {1, 3, 2, 0, 0}, /* SYS_CLK_SELECT */ + {1, 29, 2, 0, 0}, /* LOCALBUS_QE_MUXSEL */ + {1, 30, 2, 0, 0}, /* ETH_TDM_SEL */ + + /* QE_MUX_MDC */ + {1, 19, 1, 0, 1}, /* QE_MUX_MDC */ + + /* QE_MUX_MDIO */ + {1, 20, 3, 0, 1}, /* QE_MUX_MDIO */ + + /* UCC_1_MII */ + {0, 23, 2, 0, 2}, /* CLK12 */ + {0, 24, 2, 0, 1}, /* CLK9 */ + {0, 7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0 */ + {0, 9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1 */ + {0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2 */ + {0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */ + {0, 6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0 */ + {0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1 */ + {0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */ + {0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */ + {0, 5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */ + {0, 13, 1, 0, 2}, /* ENET1_TX_ER */ + {0, 4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B */ + {0, 8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B */ + {0, 17, 2, 0, 2}, /* ENET1_CRS */ + {0, 16, 2, 0, 2}, /* ENET1_COL */ + + /* UCC_3_UART */ + {1, 0, 2, 0, 2}, /* SER3_CD_B */ + {0, 28, 2, 0, 2}, /* SER3_CTS_B */ + {0, 29, 1, 0, 2}, /* SER3_RTS_B */ + {0, 30, 2, 0, 2}, /* SER3_RXD0 */ + {0, 31, 1, 0, 2}, /* SER3_TXD0 */ + + /* UCC_5_RMII */ + {1, 11, 2, 0, 1}, /* CLK13 */ + {1, 7, 1, 0, 2}, /* ENET5_TXD0_SER5_TXD0 */ + {1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1 */ + {1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0 */ + {1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1 */ + {1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B */ + {1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B */ + {1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B */ + + /* UCC_7_UART */ + {0, 22, 2, 0, 2}, /* SER7_CD_B */ + {0, 18, 2, 0, 2}, /* SER7_CTS_B */ + {0, 19, 1, 0, 2}, /* SER7_RTS_B */ + {0, 20, 2, 0, 2}, /* SER7_RXD0 */ + {0, 21, 1, 0, 2}, /* SER7_TXD0 */ + + /* TDMA - clock option is configured in OS based on board setting */ + {1, 23, 2, 0, 2}, /* TDMA_TXD */ + {1, 25, 2, 0, 2}, /* TDMA_RXD */ + {1, 26, 1, 0, 2}, /* TDMA_SYNC */ +#endif + + {0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */ +}; +#endif + +int board_early_init_f(void) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + setbits_be32(&gur->pmuxcr, + (MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP)); + + /* SDHC_DAT[4:7] not exposed to pins (use as SPI) */ + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA); + + return 0; +} + +int checkboard(void) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u8 boot_status; + + printf("Board: %s\n", CONFIG_BOARDNAME); + +#ifdef CONFIG_PHYS_64BIT + puts("(36-bit addrmap) "); +#endif + + boot_status = ((gur->porbmsr) & MPC85xx_PORBMSR_ROMLOC) + >> MPC85xx_PORBMSR_ROMLOC_SHIFT; + puts("rom_loc: "); + if (boot_status == 0x0F || boot_status == 0x0E) + puts("nor flash"); + else if (boot_status == 0x07) + puts("sd"); + else + puts("unknow"); + puts("\n"); + + return 0; +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} +#endif + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */ + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,/* perms, wimge */ + 0, flash_esel, BOOKE_PAGESZ_64M, 1);/* ts, esel, tsize, iprot */ + return 0; +} + +int board_eth_init(bd_t *bis) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[4]; + ccsr_gur_t *gur __attribute__((unused)) = + (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + if (is_serdes_configured(SGMII_TSEC2)) { + printf("eTSEC2 is in sgmii mode.\n"); + tsec_info[num].flags |= TSEC_SGMII; + } + num++; +#endif +#ifdef CONFIG_TSEC3 + SET_STD_TSEC_INFO(tsec_info[num], 3); + num++; +#endif + + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, num); + +#if defined(CONFIG_UEC_ETH) + /* QE0 and QE3 need to be exposed for UCC1 + * and UCC5 Eth mode (in PMUXCR register). + * Currently QE/LBC muxed pins assumed to be + * LBC for U-Boot and PMUXCR updated by OS if required */ + + uec_standard_init(bis); +#endif + + return pci_eth_init(bis); +} + +#if defined(CONFIG_QE) +static void fdt_board_fixup_qe_pins(void *blob) +{ + int node; + + if (!hwconfig("qe")) { + /* For QE and eLBC pins multiplexing, + * When don't use QE function, remove + * qe node from dt blob. + */ + node = fdt_path_offset(blob, "/qe"); + if (node >= 0) + fdt_del_node(blob, node); + } else { + /* For TWR Peripheral Modules - TWR-SER2 + * board only can support Signal Port MII, + * so delete one UEC node when use MII port. + */ + if (hwconfig("mii")) + node = fdt_path_offset(blob, "/qe/ucc@2400"); + else + node = fdt_path_offset(blob, "/qe/ucc@2000"); + if (node >= 0) + fdt_del_node(blob, node); + } + + return; +} +#endif + +#if defined(CONFIG_TWR_P1025) +static void fdt_board_fixup_etsec(void *blob) +{ + int node; + + /* In TWR-P1025 board, the eTSEC2 don't + * be used, remove the node from dt blob. + */ + node = fdt_path_offset(blob, "/soc/ethernet@b1000"); + if (node >= 0) + fdt_del_node(blob, node); + + return; +} +#endif + +#ifdef CONFIG_OF_BOARD_SETUP +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + + FT_FSL_PCI_SETUP; + +#ifdef CONFIG_QE + do_fixup_by_compat(blob, "fsl,qe", "status", "okay", + sizeof("okay"), 0); +#endif +#if defined(CONFIG_TWR_P1025) + fdt_board_fixup_qe_pins(blob); + fdt_board_fixup_etsec(blob); +#endif + fdt_fixup_dr_usb(blob, bd); +} +#endif diff --git a/board/freescale/p1_twr/tlb.c b/board/freescale/p1_twr/tlb.c new file mode 100644 index 0000000..c0bdc99 --- /dev/null +++ b/board/freescale/p1_twr/tlb.c @@ -0,0 +1,92 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + +#ifndef CONFIG_NAND_SPL + /* W**G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_64M, 1), + + /* W**G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_SSD_BASE, CONFIG_SYS_SSD_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_1M, 1), + +#ifdef CONFIG_PCI + /* *I*G* - PCI memory 1.5G */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O effective: 192K */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), +#endif + +#endif + +#ifdef CONFIG_SYS_RAMBOOT + /* *I*G - eSDHC boot */ + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 8, BOOKE_PAGESZ_1G, 1), +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 35f38f3..fab6f67 100644 --- a/boards.cfg +++ b/boards.cfg @@ -798,6 +798,8 @@ P1025RDB_36BIT powerpc mpc85xx p1_p2_rdb_pc freesca P1025RDB_NAND powerpc mpc85xx p1_p2_rdb_pc freescale - p1_p2_rdb_pc:P1025RDB,NAND P1025RDB_SDCARD powerpc mpc85xx p1_p2_rdb_pc freescale - p1_p2_rdb_pc:P1025RDB,SDCARD P1025RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb_pc freescale - p1_p2_rdb_pc:P1025RDB,SPIFLASH +TWR-P1025 powerpc mpc85xx p1_twr freescale - p1_twr:TWR_P1025 +TWR-P1025_36BIT powerpc mpc85xx p1_twr freescale - p1_twr:TWR_P1025,36BIT P2010RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB P2010RDB_36BIT powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB,36BIT P2010RDB_36BIT_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB,36BIT,SDCARD diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h new file mode 100644 index 0000000..e9a13cf --- /dev/null +++ b/include/configs/p1_twr.h @@ -0,0 +1,694 @@ +/* + * Copyright 2010-2011, 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * QorIQ P1 Tower boards configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#ifdef CONFIG_36BIT +#define CONFIG_PHYS_64BIT +#endif + +#if defined(CONFIG_TWR_P1025) +#define CONFIG_BOARDNAME "TWR-P1025" +#define CONFIG_P1025 +#define CONFIG_PHY_ATHEROS +#define CONFIG_QE +#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Conversion of LBC addr */ +#define CONFIG_SYS_LBC_LCRR 0x80000002 /* LB clock ratio reg */ +#endif + +#ifdef CONFIG_SDCARD +#define CONFIG_RAMBOOT_SDCARD +#define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_SYS_TEXT_BASE 0x11000000 +#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc +#endif + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 +#define CONFIG_MPC85xx + +#define CONFIG_MP + +#define CONFIG_FSL_ELBC +#define CONFIG_PCI +#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_CMD_SATA +#define CONFIG_SATA_SIL3114 +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_LIBATA +#define CONFIG_LBA48 + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +#endif +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /*sysclk for TWR-P1025 */ + +#define CONFIG_DDR_CLK_FREQ 66666666 + +#define CONFIG_HWCONFIG +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE +#define CONFIG_BTB + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ENABLE_36BIT_PHYS +#endif + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP 1 +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ +#endif + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x1fffffff +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* DDR Setup */ +#define CONFIG_FSL_DDR3 + +#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 + +#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 + +/* Default settings for DDR3 */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 +#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 +#define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 +#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 + +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 +#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 +#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 + +#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 +#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655a608 +#define CONFIG_SYS_DDR_SR_CNTR 0x00000000 +#define CONFIG_SYS_DDR_RCW_1 0x00000000 +#define CONFIG_SYS_DDR_RCW_2 0x00000000 +#define CONFIG_SYS_DDR_CONTROL 0xc70c0000 /* Type = DDR3 */ +#define CONFIG_SYS_DDR_CONTROL_2 0x04401050 +#define CONFIG_SYS_DDR_TIMING_4 0x00220001 +#define CONFIG_SYS_DDR_TIMING_5 0x03402400 + +#define CONFIG_SYS_DDR_TIMING_3 0x00020000 +#define CONFIG_SYS_DDR_TIMING_0 0x00220004 +#define CONFIG_SYS_DDR_TIMING_1 0x5c5b6544 +#define CONFIG_SYS_DDR_TIMING_2 0x0fa880de +#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 +#define CONFIG_SYS_DDR_MODE_1 0x80461320 +#define CONFIG_SYS_DDR_MODE_2 0x00008000 +#define CONFIG_SYS_DDR_INTERVAL 0x09480000 + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Memory map + * + * 0x0000_0000 0x1fff_ffff DDR Up to 512MB cacheable + * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3) + * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable + * + * Localbus cacheable (TBD) + * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable + * + * Localbus non-cacheable + * 0xec00_0000 0xefff_ffff FLASH Up to 64M non-cacheable + * 0xff90_0000 0xff97_ffff L2 SDRAM(REV.) 512K cacheable(optional) + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 + * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + */ + + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ +#define CONFIG_SYS_FLASH_BASE 0xec000000 + + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) +#else +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#endif + +#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \ + | BR_PS_16 | BR_V) + +#define CONFIG_FLASH_OR_PRELIM 0xfc0000b1 + +#define CONFIG_SYS_SSD_BASE 0xe0000000 +#define CONFIG_SYS_SSD_BASE_PHYS CONFIG_SYS_SSD_BASE +#define CONFIG_SSD_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \ + BR_PS_16 | BR_V) +#define CONFIG_SSD_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ + OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \ + OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) + +#define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM +#define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ + +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#else +/* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS +#endif +/* Size of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ + +#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ + +/* Serial Port + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +#define CONFIG_SYS_64BIT_VSPRINTF +#define CONFIG_SYS_64BIT_STRTOUL + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C spd and slave address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#undef CONFIG_ID_EEPROM + +#define CONFIG_SYS_I2C_PCA9555_ADDR 0x23 + +/* enable read and write access to EEPROM */ +#define CONFIG_CMD_EEPROM +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_HARD_SPI +#define CONFIG_FSL_ESPI + +#if defined(CONFIG_PCI) +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 2, direct to uli, tgtid 2, Base address 9000 */ +#define CONFIG_SYS_PCIE2_NAME "TWR-ELEV PCIe SLOT" +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#else +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#endif +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull +#else +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#endif +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 1, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_NAME "mini PCIe SLOT" +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#else +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 +#endif +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull +#else +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 +#endif +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 /* Defind e1000 pci Ethernet card*/ +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI +#endif + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#undef CONFIG_TSEC2 +#undef CONFIG_TSEC2_NAME +#define CONFIG_TSEC3 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 0 +#define TSEC3_PHY_ADDR 1 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#undef CONFIG_HAS_ETH2 +#endif /* CONFIG_TSEC_ENET */ + +#ifdef CONFIG_QE +/* QE microcode/firmware address */ +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xefec0000 +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#endif /* CONFIG_QE */ + +#ifdef CONFIG_TWR_P1025 +/* + * QE UEC ethernet configuration + */ +#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) + +#undef CONFIG_UEC_ETH +#define CONFIG_PHY_MODE_NEED_CHANGE + +#define CONFIG_UEC_ETH1 /* ETH1 */ +#define CONFIG_HAS_ETH0 + +#ifdef CONFIG_UEC_ETH1 +#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */ +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */ +#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 0x18 /* 0x18 for MII */ +#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII +#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 +#endif /* CONFIG_UEC_ETH1 */ + +#define CONFIG_UEC_ETH5 /* ETH5 */ +#define CONFIG_HAS_ETH1 + +#ifdef CONFIG_UEC_ETH5 +#define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */ +#define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */ +#define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC5_PHY_ADDR 0x19 /* 0x19 for RMII */ +#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII +#define CONFIG_SYS_UEC5_INTERFACE_SPEED 100 +#endif /* CONFIG_UEC_ETH5 */ +#endif /* CONFIG_TWR-P1025 */ + +/* + * Environment + */ +#ifdef CONFIG_SYS_RAMBOOT +#ifdef CONFIG_RAMBOOT_SDCARD +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_SYS_MMC_ENV_DEV 0 +#else +#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_SIZE 0x2000 +#endif +#else +#define CONFIG_ENV_IS_IN_FLASH +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 +#define CONFIG_ENV_ADDR 0xfff80000 +#else +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#endif +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO + +/* + * USB + */ +#define CONFIG_HAS_FSL_DR_USB + +#if defined(CONFIG_HAS_FSL_DR_USB) +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#endif +#endif + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#endif + +#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \ + || defined(CONFIG_FSL_SATA) +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_HOSTNAME unknown +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#define CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + + +#define CONFIG_EXTRA_ENV_SETTINGS \ +"netdev=eth0\0" \ +"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ +"loadaddr=1000000\0" \ +"bootfile=uImage\0" \ +"dtbfile=twr-p1025_32b.dtb\0" \ +"ramdiskfile=rootfs.ext2.gz.uboot\0" \ +"qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0" \ +"tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ +"kernelflash=tftpboot $loadaddr $bootfile; " \ + "protect off 0xefa80000 +$filesize; " \ + "erase 0xefa80000 +$filesize; " \ + "cp.b $loadaddr 0xefa80000 $filesize; " \ + "protect on 0xefa80000 +$filesize; " \ + "cmp.b $loadaddr 0xefa80000 $filesize\0" \ +"dtbflash=tftpboot $loadaddr $dtbfile; " \ + "protect off 0xefe80000 +$filesize; " \ + "erase 0xefe80000 +$filesize; " \ + "cp.b $loadaddr 0xefe80000 $filesize; " \ + "protect on 0xefe80000 +$filesize; " \ + "cmp.b $loadaddr 0xefe80000 $filesize\0" \ +"ramdiskflash=tftpboot $loadaddr $ramdiskfile; " \ + "protect off 0xeeb80000 +$filesize; " \ + "erase 0xeeb80000 +$filesize; " \ + "cp.b $loadaddr 0xeeb80000 $filesize; " \ + "protect on 0xeeb80000 +$filesize; " \ + "cmp.b $loadaddr 0xeeb80000 $filesize\0" \ +"qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; " \ + "protect off 0xefec0000 +$filesize; " \ + "erase 0xefec0000 +$filesize; " \ + "cp.b $loadaddr 0xefec0000 $filesize; " \ + "protect on 0xefec0000 +$filesize; " \ + "cmp.b $loadaddr 0xefec0000 $filesize\0" \ +"consoledev=ttyS0\0" \ +"ramdiskaddr=2000000\0" \ +"ramdiskfile=rootfs.ext2.gz.uboot\0" \ +"fdtaddr=c00000\0" \ +"bdev=sda1\0" \ +"jffs2nor=mtdblock3\0" \ +"norbootaddr=ef080000\0" \ +"norfdtaddr=ef040000\0" \ +"jffs2nand=mtdblock9\0" \ +"nandbootaddr=100000\0" \ +"nandfdtaddr=80000\0" \ +"ramdisk_size=120000\0" \ +"usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \ + "console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000" + +#define CONFIG_NFSBOOTCOMMAND \ +"setenv bootargs root=/dev/nfs rw " \ +"nfsroot=$serverip:$rootpath " \ +"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ +"console=$consoledev,$baudrate $othbootargs;" \ +"tftp $loadaddr $bootfile;" \ +"tftp $fdtaddr $fdtfile;" \ +"bootm $loadaddr - $fdtaddr" + +#define CONFIG_HDBOOT \ +"setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ +"console=$consoledev,$baudrate $othbootargs;" \ +"usb start;" \ +"ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ +"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ +"bootm $loadaddr - $fdtaddr" + +#define CONFIG_USB_FAT_BOOT \ +"setenv bootargs root=/dev/ram rw " \ +"console=$consoledev,$baudrate $othbootargs " \ +"ramdisk_size=$ramdisk_size;" \ +"usb start;" \ +"fatload usb 0:2 $loadaddr $bootfile;" \ +"fatload usb 0:2 $fdtaddr $fdtfile;" \ +"fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ +"bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_USB_EXT2_BOOT \ +"setenv bootargs root=/dev/ram rw " \ +"console=$consoledev,$baudrate $othbootargs " \ +"ramdisk_size=$ramdisk_size;" \ +"usb start;" \ +"ext2load usb 0:4 $loadaddr $bootfile;" \ +"ext2load usb 0:4 $fdtaddr $fdtfile;" \ +"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ +"bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_NORBOOT \ +"setenv bootargs root=/dev/$jffs2nor rw " \ +"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ +"bootm $norbootaddr - $norfdtaddr" + +#define CONFIG_RAMBOOTCOMMAND_TFTP \ +"setenv bootargs root=/dev/ram rw " \ +"console=$consoledev,$baudrate $othbootargs " \ +"ramdisk_size=$ramdisk_size;" \ +"tftp $ramdiskaddr $ramdiskfile;" \ +"tftp $loadaddr $bootfile;" \ +"tftp $fdtaddr $fdtfile;" \ +"bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ +"setenv bootargs root=/dev/ram rw " \ +"console=$consoledev,$baudrate $othbootargs " \ +"ramdisk_size=$ramdisk_size;" \ +"bootm 0xefa80000 0xeeb80000 0xefe80000" + +#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND + +#endif /* __CONFIG_H */