Signed-off-by: Heiko Schocher hs@denx.de Cc: Tom Rini trini@ti.com --- arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c | 6 ++++++ arch/arm/include/asm/arch-davinci/pinmux_defs.h | 3 ++- 2 Dateien geändert, 8 Zeilen hinzugefügt(+), 1 Zeile entfernt(-)

diff --git a/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c b/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c index f603f2f..6105f63 100644 --- a/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c +++ b/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c @@ -28,6 +28,11 @@ const struct pinmux_config uart0_pins_txrx[] = { { pinmux(3), 2, 5 }, /* UART0_TXD */ };

+const struct pinmux_config uart0_pins_rtscts[] = { + { pinmux(3), 2, 6 }, + { pinmux(3), 2, 7 }, +}; + const struct pinmux_config uart1_pins_txrx[] = { { pinmux(4), 2, 6 }, /* UART1_RXD */ { pinmux(4), 2, 7 }, /* UART1_TXD */ @@ -51,6 +56,7 @@ const struct pinmux_config emac_pins_rmii[] = { { pinmux(14), 8, 5 }, /* RMII_RXD[1] */ { pinmux(14), 8, 6 }, /* RMII_RXD[0] */ { pinmux(14), 8, 7 }, /* RMII_RXER */ + { pinmux(15), 0, 0 }, /* RMII_MHz_50_CLK */ { pinmux(15), 8, 1 }, /* RMII_CRS_DV */ };

diff --git a/arch/arm/include/asm/arch-davinci/pinmux_defs.h b/arch/arm/include/asm/arch-davinci/pinmux_defs.h index 4d45799..2d82af5 100644 --- a/arch/arm/include/asm/arch-davinci/pinmux_defs.h +++ b/arch/arm/include/asm/arch-davinci/pinmux_defs.h @@ -23,12 +23,13 @@ extern const struct pinmux_config spi1_pins_scs0[1];

/* UART pin muxer settings */ extern const struct pinmux_config uart0_pins_txrx[2]; +extern const struct pinmux_config uart0_pins_rtscts[2]; extern const struct pinmux_config uart1_pins_txrx[2]; extern const struct pinmux_config uart2_pins_txrx[2]; extern const struct pinmux_config uart2_pins_rtscts[2];

/* EMAC pin muxer settings*/ -extern const struct pinmux_config emac_pins_rmii[7]; +extern const struct pinmux_config emac_pins_rmii[8]; extern const struct pinmux_config emac_pins_rmii_clk_source[1]; extern const struct pinmux_config emac_pins_mii[15]; extern const struct pinmux_config emac_pins_mdio[2];

add the am1808 based ipam390 board from Barix.

- 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM interface - 128MByte, NAND Flash, 8bit databus to the NANDFlash Interface - Ethernet PHY Micrel KSZ8051R via RMII - Console on UART 0 - booting fron nand flash - spl falcon bootmode

Signed-off-by: Heiko Schocher hs@denx.de Cc: Tom Rini trini@ti.com

--- Needed patches posted on the ML but not in mainline: - [U-Boot,05/10] arm: spl: For Falcon Mode, set a default machid of ~0 http://patchwork.ozlabs.org/patch/264336/ --- MAINTAINERS | 1 + board/Barix/ipam390/Makefile | 29 +++ board/Barix/ipam390/README.ipam390 | 229 +++++++++++++++++++ board/Barix/ipam390/ipam390-ais-uart.cfg | 202 +++++++++++++++++ board/Barix/ipam390/ipam390.c | 348 +++++++++++++++++++++++++++++ board/Barix/ipam390/u-boot-spl-ipam390.lds | 53 +++++ boards.cfg | 1 + include/configs/ipam390.h | 331 +++++++++++++++++++++++++++ 8 Dateien geändert, 1194 Zeilen hinzugefügt(+) create mode 100644 board/Barix/ipam390/Makefile create mode 100644 board/Barix/ipam390/README.ipam390 create mode 100644 board/Barix/ipam390/ipam390-ais-uart.cfg create mode 100644 board/Barix/ipam390/ipam390.c create mode 100644 board/Barix/ipam390/u-boot-spl-ipam390.lds create mode 100644 include/configs/ipam390.h

diff --git a/MAINTAINERS b/MAINTAINERS index 022cb70..593529f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -448,6 +448,7 @@ Heiko Schocher hs@denx.de cam_enc_4xx davinci/ARM926EJS charon MPC5200 ids8247 MPC8247 + ipam390 davinci/ARM926EJS jupiter MPC5200 kmsupx5 MPC8321 mucmc52 MPC5200 diff --git a/board/Barix/ipam390/Makefile b/board/Barix/ipam390/Makefile new file mode 100644 index 0000000..c84ee05 --- /dev/null +++ b/board/Barix/ipam390/Makefile @@ -0,0 +1,29 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn ksi@koi8.net +# +# SPDX-License-Identifier: GPL-2.0+ +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS += ipam390.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/Barix/ipam390/README.ipam390 b/board/Barix/ipam390/README.ipam390 new file mode 100644 index 0000000..2d155a3 --- /dev/null +++ b/board/Barix/ipam390/README.ipam390 @@ -0,0 +1,229 @@ +Summary +======= +The README is for the boot procedure on the ipam390 board + +In the context of U-Boot, the board is booted in three stages. The initial +bootloader which executes upon reset is the ROM Boot Loader (RBL) and sits +in the internal ROM. The RBL initializes the internal memory and then +depending on the exact board and pin configurations will initialize another +controller (such as NAND) to continue the boot process by loading +the secondary program loader (SPL). The SPL will initialize the system +further (some clocks, SDRAM). As on this board is used the falcon boot +mode, now 2 ways are possible depending on the GPIO 7_14 input pin, +connected with the "soft reset switch" + +If this pin is logical 1 (high level): +spl code starts the kernel image without delay + +If this pin is logical 0 (low level): +spl code starts the u-boot image + +AIS is an image format defined by TI for the images that are to be loaded +to memory by the RBL. The image is divided into a series of sections and +the image's entry point is specified. Each section comes with meta data +like the target address the section is to be copied to and the size of the +section, which is used by the RBL to load the image. At the end of the +image the RBL jumps to the image entry point. The AIS format allows for +other things such as programming the clocks and SDRAM if the header is +programmed for it. We do not take advantage of this and instead use SPL as +it allows for additional flexibility (run-time detect of board revision, +loading the next image from a different media, etc). + +Compilation +=========== +run "./MAKEALL ipam390" in the u-boot source tree. +Once this build completes you will have a u-boot.ais file that needs to +be written to the nand flash. + +Flashing the images to NAND +========================== +The AIS image can be written to NAND flash using the following commands. +Assuming that the network is configured and enabled and the u-boot.ais file +is tftp'able. + +U-Boot > print upd_uboot +upd_uboot=tftp c0000000 ${u-boot};nand erase.part u-boot;nand write c0000000 20000 ${filesize} +U-Boot > +U-Boot > run upd_uboot +Using DaVinci-EMAC device +TFTP from server 192.168.1.1; our IP address is 192.168.20.71 +Filename '/tftpboot/ipam390/u-boot.ais'. +Load address: 0xc0000000 +Loading: ################################## + 1.5 MiB/s +done +Bytes transferred = 493716 (78894 hex) + +NAND erase.part: device 0 offset 0x20000, size 0x160000 +Erasing at 0x160000 -- 100% complete. +OK + +NAND write: device 0 offset 0x20000, size 0x78894 + 493716 bytes written: OK +U-Boot > + +Recovery +======== + +In the case of a "bricked" board, you need to use the TI tools found +here[1] to create an uboot-uart-ais.bin file + +- cd to the u-boot source tree + +- compile the u-boot for the ipam390 board: +$ ./MAKEALL ipam390 + + -> Now we shall have u-boot.bin + +- Create u-boot-uart-ais.bin +$ mono HexAIS_OMAP-L138.exe -entrypoint 0xC1080000 -ini +ipam390-ais-uart.cfg -o ./uboot-uart-ais.bin ./u-boot.bin@0xC1080000; + +Note: The ipam390-ais-uart.cfg is found in the board directory +for the ipam390 board, u-boot:/board/Barix/ipam390/ipam390-ais-uart.cfg + +- We can now run bootloader on IPAM390 via UART using the command below: + +$ mono ./slh_OMAP-L138.exe -waitForDevice -v -p /dev/tty.UC-232AC uboot-uart-ais.bin +NOTE: Do not cancel the command execution! The command takes 20+ seconds +to upload u-boot over serial and run it! +Outcome: +Waiting for the OMAP-L138... +(AIS Parse): Read magic word 0x41504954. +(AIS Parse): Waiting for BOOTME... (power on or reset target now) +(AIS Parse): BOOTME received! +(AIS Parse): Performing Start-Word Sync... +(AIS Parse): Performing Ping Opcode Sync... +(AIS Parse): Processing command 0: 0x5853590D. +(AIS Parse): Performing Opcode Sync... +(AIS Parse): Executing function... +(AIS Parse): Processing command 1: 0x5853590D. +(AIS Parse): Performing Opcode Sync... +(AIS Parse): Executing function... +(AIS Parse): Processing command 2: 0x5853590D. +(AIS Parse): Performing Opcode Sync... +(AIS Parse): Executing function... +(AIS Parse): Processing command 3: 0x5853590D. +(AIS Parse): Performing Opcode Sync... +(AIS Parse): Executing function... +(AIS Parse): Processing command 4: 0x5853590D. +(AIS Parse): Performing Opcode Sync... +(AIS Parse): Executing function... +(AIS Parse): Processing command 5: 0x58535901. +(AIS Parse): Performing Opcode Sync... +(AIS Parse): Loading section... +(AIS Parse): Loaded 326516-Byte section to address 0xC1080000. +(AIS Parse): Processing command 6: 0x58535906. +(AIS Parse): Performing Opcode Sync... +(AIS Parse): Performing jump and close... +(AIS Parse): AIS complete. Jump to address 0xC1080000. +(AIS Parse): Waiting for DONE... +(AIS Parse): Boot completed successfully. + +Operation completed successfully. + +Falcon Bootmode (boot linux without booting U-Boot) +=================================================== + +The Falcon Mode extends this way allowing to start the Linux kernel directly +from SPL. A new command is added to U-Boot to prepare the parameters that SPL +must pass to the kernel, using ATAGS or Device Tree. + +In normal mode, these parameters are generated each time before +loading the kernel, passing to Linux the address in memory where +the parameters can be read. +With Falcon Mode, this snapshot can be saved into persistent storage and SPL is +informed to load it before running the kernel. + +To boot the kernel, these steps under a Falcon-aware U-Boot are required: + +1. Boot the board into U-Boot. +Use the "spl export" command to generate the kernel parameters area or the DT. +U-Boot runs as when it boots the kernel, but stops before passing the control +to the kernel. + +Here the command sequence for the ipam390 board: +- load the linux kernel image into ram: + +U-Boot > nand read c0100000 2 200000 400000 + +NAND read: device 0 offset 0x200000, size 0x400000 + 4194304 bytes read: OK + +- generate the bootparms image: + +U-Boot > spl export atags c0100000 +## Booting kernel from Legacy Image at c0100000 ... + Image Name: Linux-3.5.1 + Image Type: ARM Linux Kernel Image (uncompressed) + Data Size: 2504280 Bytes = 2.4 MiB + Load Address: c0008000 + Entry Point: c0008000 + Verifying Checksum ... OK + Loading Kernel Image ... OK +subcommand not supported +subcommand not supported +Argument image is now in RAM at: 0xc0000100 + +- copy the bootparms image into nand: + +U-Boot > mtdparts + +device nand0 <davinci_nand.0>, # parts = 6 + #: name size offset mask_flags + 0: u-boot-env 0x00020000 0x00000000 0 + 1: u-boot 0x00160000 0x00020000 0 + 2: bootparms 0x00020000 0x00180000 0 + 3: factory-info 0x00060000 0x001a0000 0 + 4: kernel 0x00400000 0x00200000 0 + 5: rootfs 0x07a00000 0x00600000 0 + +active partition: nand0,0 - (u-boot-env) 0x00020000 @ 0x00000000 + +defaults: +mtdids : nand0=davinci_nand.0 +mtdparts: mtdparts=davinci_nand.0:128k(u-boot-env),1408k(u-boot),128k(bootparms),384k(factory-info),4M(kernel),-(rootfs) +U-Boot > nand erase.part bootparms + +NAND erase.part: device 0 offset 0x180000, size 0x20000 +Erasing at 0x180000 -- 100% complete. +OK +U-Boot > nand write c0000100 180000 20000 + +NAND write: device 0 offset 0x180000, size 0x20000 + 131072 bytes written: OK +U-Boot > + +You can use also the predefined U-Boot Environment variable "setbootparms", +which will do all the above steps in one command: + +U-Boot > print setbootparms +setbootparms=nand read c0100000 200000 400000;spl export atags c0100000;nand erase.part bootparms;nand write c0000100 180000 20000 +U-Boot > run setbootparms + +NAND read: device 0 offset 0x200000, size 0x400000 + 4194304 bytes read: OK +## Booting kernel from Legacy Image at c0100000 ... + Image Name: Linux-3.5.1 + Image Type: ARM Linux Kernel Image (uncompressed) + Data Size: 2504280 Bytes = 2.4 MiB + Load Address: c0008000 + Entry Point: c0008000 + Verifying Checksum ... OK + Loading Kernel Image ... OK +subcommand not supported +subcommand not supported +Argument image is now in RAM at: 0xc0000100 + +NAND erase.part: device 0 offset 0x180000, size 0x20000 +Erasing at 0x180000 -- 100% complete. +OK + +NAND write: device 0 offset 0x180000, size 0x20000 + 131072 bytes written: OK +U-Boot > + +Links +===== +[1] + http://sourceforge.net/projects/dvflashutils/files/OMAP-L138/ diff --git a/board/Barix/ipam390/ipam390-ais-uart.cfg b/board/Barix/ipam390/ipam390-ais-uart.cfg new file mode 100644 index 0000000..e1a99f2 --- /dev/null +++ b/board/Barix/ipam390/ipam390-ais-uart.cfg @@ -0,0 +1,202 @@ +; General settings that can be overwritten in the host code +; that calls the AISGen library. +[General] + +; Can be 8 or 16 - used in emifa +busWidth=8 + +; SPIMASTER,I2CMASTER,EMIFA,NAND,EMAC,UART,PCI,HPI,USB,MMC_SD,VLYNQ,RAW +BootMode=UART + +; 8,16,24 - used for SPI,I2C +;AddrWidth=8 + +; NO_CRC,SECTION_CRC,SINGLE_CRC +crcCheckType=NO_CRC + +; This section allows setting the PLL0 system clock with a +; specified multiplier and divider as shown. The clock source +; can also be chosen for internal or external. +; |------24|------16|-------8|-------0| +; PLL0CFG0: | CLKMODE| PLLM | PREDIV | POSTDIV| +; PLL0CFG1: | RSVD | PLLDIV1| PLLDIV3| PLLDIV7| +;[PLL0CONFIG] +;PLL0CFG0 = 0x00180001 +;PLL0CFG1 = 0x00000205 + +[PLLANDCLOCKCONFIG] +PLL0CFG0 = 0x00180001 +PLL0CFG1 = 0x00000205 +PERIPHCLKCFG = 0x00000051 + +; This section allows setting up the PLL1. Usually this will +; take place as part of the EMIF3a DDR setup. The format of +; the input args is as follows: +; |------24|------16|-------8|-------0| +; PLL1CFG0: | PLLM| POSTDIV| PLLDIV1| PLLDIV2| +; PLL1CFG1: | RSVD | PLLDIV3| +[PLL1CONFIG] +PLL1CFG0 = 0x18010001 +PLL1CFG1 = 0x00000002 + +; This section lets us configure the peripheral interface +; of the current booting peripheral (I2C, SPI, or UART). +; Use with caution. The format of the PERIPHCLKCFG field +; is as follows: +; SPI: |------24|------16|-------8|-------0| +; | RSVD |PRESCALE| +; +; I2C: |------24|------16|-------8|-------0| +; | RSVD |PRESCALE| CLKL | CLKH | +; +; UART: |------24|------16|-------8|-------0| +; | RSVD | OSR | DLH | DLL | +[PERIPHCLKCFG] +PERIPHCLKCFG = 0x00000051 + +; This section can be used to configure the PLL1 and the EMIF3a registers +; for starting the DDR2 interface. +; See PLL1CONFIG section for the format of the PLL1CFG fields. +; |------24|------16|-------8|-------0| +; PLL1CFG0: | PLL1CFG | +; PLL1CFG1: | PLL1CFG | +; DDRPHYC1R: | DDRPHYC1R | +; SDCR: | SDCR | +; SDTIMR: | SDTIMR | +; SDTIMR2: | SDTIMR2 | +; SDRCR: | SDRCR | +; CLK2XSRC: | CLK2XSRC | +[EMIF3DDR] +PLL1CFG0 = 0x18010001 +PLL1CFG1 = 0x00000002 +DDRPHYC1R = 0x000000C2 +SDCR = 0x0017C432 +SDTIMR = 0x26922A09 +SDTIMR2 = 0x4414C722 +SDRCR = 0x00000498 +CLK2XSRC = 0x00000000 + +; This section can be used to configure the EMIFA to use +; CS0 as an SDRAM interface. The fields required to do this +; are given below. +; |------24|------16|-------8|-------0| +; SDBCR: | SDBCR | +; SDTIMR: | SDTIMR | +; SDRSRPDEXIT: | SDRSRPDEXIT | +; SDRCR: | SDRCR | +; DIV4p5_CLK_ENABLE: | DIV4p5_CLK_ENABLE | +;[EMIF25SDRAM] +;SDBCR = 0x00004421 +;SDTIMR = 0x42215810 +;SDRSRPDEXIT = 0x00000009 +;SDRCR = 0x00000410 +;DIV4p5_CLK_ENABLE = 0x00000001 + +; This section can be used to configure the async chip selects +; of the EMIFA (CS2-CS5). The fields required to do this +; are given below. +; |------24|------16|-------8|-------0| +; A1CR: | A1CR | +; A2CR: | A2CR | +; A3CR: | A3CR | +; A4CR: | A4CR | +; NANDFCR: | NANDFCR | +;[EMIF25ASYNC] +;A1CR = 0x00000000 +;A2CR = 0x00000000 +;A3CR = 0x00000000 +;A4CR = 0x00000000 +;NANDFCR = 0x00000000 +[EMIF25ASYNC] +A1CR = 0x00000000 +A2CR = 0x3FFFFFFE +A3CR = 0x00000000 +A4CR = 0x00000000 +NANDFCR = 0x00000012 + +; This section should be used in place of PLL0CONFIG when +; the I2C, SPI, or UART modes are being used. This ensures that +; the system PLL and the peripheral's clocks are changed together. +; See PLL0CONFIG section for the format of the PLL0CFG fields. +; See PERIPHCLKCFG section for the format of the CLKCFG field. +; |------24|------16|-------8|-------0| +; PLL0CFG0: | PLL0CFG | +; PLL0CFG1: | PLL0CFG | +; PERIPHCLKCFG: | CLKCFG | +;[PLLANDCLOCKCONFIG] +;PLL0CFG0 = 0x00180001 +;PLL0CFG1 = 0x00000205 +;PERIPHCLKCFG = 0x00010032 + +; This section should be used to setup the power state of modules +; of the two PSCs. This section can be included multiple times to +; allow the configuration of any or all of the device modules. +; |------24|------16|-------8|-------0| +; LPSCCFG: | PSCNUM | MODULE | PD | STATE | +;[PSCCONFIG] +;LPSCCFG= + +; This section allows setting of a single PINMUX register. +; This section can be included multiple times to allow setting +; as many PINMUX registers as needed. +; |------24|------16|-------8|-------0| +; REGNUM: | regNum | +; MASK: | mask | +; VALUE: | value | +;[PINMUX] +;REGNUM = 5 +;MASK = 0x00FF0000 +;VALUE = 0x00880000 + +; No Params required - simply include this section for the fast boot +; function to be called +;[FASTBOOT] + +; This section allows setting up the PLL1. Usually this will +; take place as part of the EMIF3a DDR setup. The format of +; the input args is as follows: +; |------24|------16|-------8|-------0| +; PLL1CFG0: | PLLM| POSTDIV| PLLDIV1| PLLDIV2| +; PLL1CFG1: | RSVD | PLLDIV3| +;[PLL1CONFIG] +;PLL1CFG0 = 0x15010001 +;PLL1CFG1 = 0x00000002 + +; This section can be used to configure the PLL1 and the EMIF3a registers +; for starting the DDR2 interface on ARM-boot D800K002 devices. +; |------24|------16|-------8|-------0| +; DDRPHYC1R: | DDRPHYC1R | +; SDCR: | SDCR | +; SDTIMR: | SDTIMR | +; SDTIMR2: | SDTIMR2 | +; SDRCR: | SDRCR | +; CLK2XSRC: | CLK2XSRC | +;[ARM_EMIF3DDR_PATCHFXN] +;DDRPHYC1R = 0x000000C2 +;SDCR = 0x0017C432 +;SDTIMR = 0x26922A09 +;SDTIMR2 = 0x4414C722 +;SDRCR = 0x00000498 +;CLK2XSRC = 0x00000000 + +; This section can be used to configure the PLL1 and the EMIF3a registers +; for starting the DDR2 interface on DSP-boot D800K002 devices. +; |------24|------16|-------8|-------0| +; DDRPHYC1R: | DDRPHYC1R | +; SDCR: | SDCR | +; SDTIMR: | SDTIMR | +; SDTIMR2: | SDTIMR2 | +; SDRCR: | SDRCR | +; CLK2XSRC: | CLK2XSRC | +;[DSP_EMIF3DDR_PATCHFXN] +;DDRPHYC1R = 0x000000C4 +;SDCR = 0x08134632 +;SDTIMR = 0x26922A09 +;SDTIMR2 = 0x0014C722 +;SDRCR = 0x00000492 +;CLK2XSRC = 0x00000000 + +;[INPUTFILE] +;FILENAME=u-boot.bin +;LOADADDRESS=0xC1080000 +;ENTRYPOINTADDRESS=0xC1080000 diff --git a/board/Barix/ipam390/ipam390.c b/board/Barix/ipam390/ipam390.c new file mode 100644 index 0000000..f3f276e --- /dev/null +++ b/board/Barix/ipam390/ipam390.c @@ -0,0 +1,348 @@ +/* + * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. + * Based on: + * U-Boot:board/davinci/da8xxevm/da850evm.c + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on da830evm.c. Original Copyrights follow: + * + * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. nick.thompson@gefanuc.com + * Copyright (C) 2007 Sergey Kubushyn ksi@koi8.net + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <net.h> +#include <netdev.h> +#include <spi.h> +#include <spi_flash.h> +#include <asm/arch/hardware.h> +#include <asm/arch/emif_defs.h> +#include <asm/arch/emac_defs.h> +#include <asm/arch/pinmux_defs.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> +#include <asm/errno.h> +#include <asm/gpio.h> +#include <hwconfig.h> +#include <bootstage.h> + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_DRIVER_TI_EMAC +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII +#define HAS_RMII 1 +#else +#define HAS_RMII 0 +#endif +#endif /* CONFIG_DRIVER_TI_EMAC */ + +void dsp_lpsc_on(unsigned domain, unsigned int id) +{ + dv_reg_p mdstat, mdctl, ptstat, ptcmd; + struct davinci_psc_regs *psc_regs; + + psc_regs = davinci_psc0_regs; + mdstat = &psc_regs->psc0.mdstat[id]; + mdctl = &psc_regs->psc0.mdctl[id]; + ptstat = &psc_regs->ptstat; + ptcmd = &psc_regs->ptcmd; + + while (*ptstat & (0x1 << domain)) + ; + + if ((*mdstat & 0x1f) == 0x03) + return; /* Already on and enabled */ + + *mdctl |= 0x03; + + *ptcmd = 0x1 << domain; + + while (*ptstat & (0x1 << domain)) + ; + while ((*mdstat & 0x1f) != 0x03) + ; /* Probably an overkill... */ +} + +static void dspwake(void) +{ + unsigned *resetvect = (unsigned *)DAVINCI_L3CBARAM_BASE; + u32 val; + + /* if the device is ARM only, return */ + if ((readl(CHIP_REV_ID_REG) & 0x3f) == 0x10) + return; + + if (hwconfig_subarg_cmp_f("dsp", "wake", "no", NULL)) + return; + + *resetvect++ = 0x1E000; /* DSP Idle */ + /* clear out the next 10 words as NOP */ + memset(resetvect, 0, sizeof(unsigned) * 10); + + /* setup the DSP reset vector */ + writel(DAVINCI_L3CBARAM_BASE, HOST1CFG); + + dsp_lpsc_on(1, DAVINCI_LPSC_GEM); + val = readl(PSC0_MDCTL + (15 * 4)); + val |= 0x100; + writel(val, (PSC0_MDCTL + (15 * 4))); +} + +int misc_init_r(void) +{ + dspwake(); + return 0; +} + +static const struct pinmux_config gpio_pins[] = { + /* GP7[14] selects bootmode*/ + { pinmux(16), 8, 3 }, /* GP7[14] */ +}; + +const struct pinmux_resource pinmuxes[] = { +#ifdef CONFIG_DRIVER_TI_EMAC + PINMUX_ITEM(emac_pins_mdio), +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII + PINMUX_ITEM(emac_pins_rmii), +#else + PINMUX_ITEM(emac_pins_mii), +#endif +#endif + PINMUX_ITEM(uart2_pins_txrx), + PINMUX_ITEM(uart2_pins_rtscts), + PINMUX_ITEM(uart0_pins_txrx), + PINMUX_ITEM(uart0_pins_rtscts), +#ifdef CONFIG_NAND_DAVINCI + PINMUX_ITEM(emifa_pins_cs3), + PINMUX_ITEM(emifa_pins_nand), +#endif + PINMUX_ITEM(gpio_pins), +}; + +const int pinmuxes_size = ARRAY_SIZE(pinmuxes); + +const struct lpsc_resource lpsc[] = { + { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ + { DAVINCI_LPSC_EMAC }, /* image download */ + { DAVINCI_LPSC_UART2 }, /* console */ + { DAVINCI_LPSC_UART0 }, /* console */ + { DAVINCI_LPSC_GPIO }, +}; + +const int lpsc_size = ARRAY_SIZE(lpsc); + +#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK +#define CONFIG_DA850_EVM_MAX_CPU_CLK 300000000 +#endif + +#define REV_AM18X_EVM 0x100 + +/* + * get_board_rev() - setup to pass kernel board revision information + * Returns: + * bit[0-3] Maximum cpu clock rate supported by onboard SoC + * 0000b - 300 MHz + * 0001b - 372 MHz + * 0010b - 408 MHz + * 0011b - 456 MHz + */ +u32 get_board_rev(void) +{ + char *s; + u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK; + u32 rev = 0; + + s = getenv("maxcpuclk"); + if (s) + maxcpuclk = simple_strtoul(s, NULL, 10); + + if (maxcpuclk >= 456000000) + rev = 3; + else if (maxcpuclk >= 408000000) + rev = 2; + else if (maxcpuclk >= 372000000) + rev = 1; +#ifdef CONFIG_DA850_AM18X_EVM + rev |= REV_AM18X_EVM; +#endif + return rev; +} + +int board_early_init_f(void) +{ + /* + * Power on required peripherals + * ARM does not have access by default to PSC0 and PSC1 + * assuming here that the DSP bootloader has set the IOPU + * such that PSC access is available to ARM + */ + if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc))) + return 1; + + return 0; +} + +int board_init(void) +{ +#ifndef CONFIG_USE_IRQ + irq_init(); +#endif + + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* setup the SUSPSRC for ARM to control emulation suspend */ + writel(readl(&davinci_syscfg_regs->suspsrc) & + ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | + DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 | + DAVINCI_SYSCFG_SUSPSRC_UART0), + &davinci_syscfg_regs->suspsrc); + + /* configure pinmux settings */ + if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes))) + return 1; + +#ifdef CONFIG_DRIVER_TI_EMAC + davinci_emac_mii_mode_sel(HAS_RMII); +#endif /* CONFIG_DRIVER_TI_EMAC */ + + /* enable the console UART */ + writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | + DAVINCI_UART_PWREMU_MGMT_UTRST), +#if (CONFIG_SYS_NS16550_COM1 == DAVINCI_UART0_BASE) + &davinci_uart0_ctrl_regs->pwremu_mgmt); +#else + &davinci_uart2_ctrl_regs->pwremu_mgmt); +#endif + return 0; +} + +#ifdef CONFIG_DRIVER_TI_EMAC +/* + * Initializes on-board ethernet controllers. + */ +int board_eth_init(bd_t *bis) +{ + if (!davinci_emac_initialize()) { + printf("Error: Ethernet init failed!\n"); + return -1; + } + + return 0; +} +#endif /* CONFIG_DRIVER_TI_EMAC */ + +static int init_led(int gpio, char *name, int val) +{ + int ret; + + ret = gpio_request(gpio, name); + if (ret) + return -1; + ret = gpio_direction_output(gpio, val); + if (ret) + return -1; + + return gpio; +} + +#define LED_ON 0 +#define LED_OFF 1 + +#if !defined(CONFIG_SPL_BUILD) +#ifdef CONFIG_SHOW_BOOT_PROGRESS +void show_boot_progress(int status) +{ + static int red; + static int green; + + if (red == 0) + red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF); + if (red != CONFIG_IPAM390_GPIO_LED_RED) + return; + if (green == 0) + green = init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", + LED_OFF); + if (green != CONFIG_IPAM390_GPIO_LED_GREEN) + return; + + switch (status) { + case BOOTSTAGE_ID_RUN_OS: + /* + * set normal state + * LED Red : off + * LED green: off + */ + gpio_set_value(red, LED_OFF); + gpio_set_value(green, LED_OFF); + break; + case BOOTSTAGE_ID_MAIN_LOOP: + /* + * U-Boot operation + * LED Red : on + * LED green: on + */ + gpio_set_value(red, LED_ON); + gpio_set_value(green, LED_ON); + break; + } +} +#endif +#endif + +#ifdef CONFIG_SPL_OS_BOOT +int spl_start_uboot(void) +{ + int ret; + int bootmode = 0; + + /* + * GP7[14] selects bootmode: + * 1: boot linux + * 0: boot u-boot + * if error accessing gpio boot U-Boot + * + * SPL bootmode + * 0: boot linux + * 1: boot u-boot + */ + ret = gpio_request(CONFIG_IPAM390_GPIO_BOOTMODE , "bootmode"); + if (ret) + bootmode = 1; + if (!bootmode) { + ret = gpio_direction_input(CONFIG_IPAM390_GPIO_BOOTMODE); + if (ret) + bootmode = 1; + } + if (!bootmode) + ret = gpio_get_value(CONFIG_IPAM390_GPIO_BOOTMODE); + if (!bootmode) + if (ret == 0) + bootmode = 1; + if (bootmode) { + /* + * Booting U-Boot + * LED Red : on + * LED green: off + */ + init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON); + init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF); + } else { + /* + * Booting Linux + * LED Red : off + * LED green: off + */ + init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF); + init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF); + } + return bootmode; +} +#endif diff --git a/board/Barix/ipam390/u-boot-spl-ipam390.lds b/board/Barix/ipam390/u-boot-spl-ipam390.lds new file mode 100644 index 0000000..5480d1f --- /dev/null +++ b/board/Barix/ipam390/u-boot-spl-ipam390.lds @@ -0,0 +1,53 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, garyj@denx.de + * + * (C) Copyright 2008 + * Guennadi Liakhovetki, DENX Software Engineering, lg@denx.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE,\ + LENGTH = CONFIG_SPL_MAX_FOOTPRINT } + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + __start = .; + arch/arm/cpu/arm926ejs/start.o (.text*) + *(.text*) + } >.sram + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram + + . = ALIGN(4); + .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram + + . = ALIGN(4); + .rel.dyn : { + __rel_dyn_start = .; + *(.rel*) + __rel_dyn_end = .; + } >.sram + + .bss : + { + . = ALIGN(4); + __bss_start = .; + *(.bss*) + . = ALIGN(4); + __bss_end = .; + } >.sram + + __image_copy_end = .; + _end = .; +} diff --git a/boards.cfg b/boards.cfg index 3f11f1d..f9ca099 100644 --- a/boards.cfg +++ b/boards.cfg @@ -140,6 +140,7 @@ pm9g45 arm arm926ejs pm9g45 ronetix portuxg20 arm arm926ejs stamp9g20 taskit at91 stamp9g20:AT91SAM9G20,PORTUXG20 stamp9g20 arm arm926ejs stamp9g20 taskit at91 stamp9g20:AT91SAM9G20 cam_enc_4xx arm arm926ejs cam_enc_4xx ait davinci cam_enc_4xx +ipam390 arm arm926ejs ipam390 Barix davinci da830evm arm arm926ejs da8xxevm davinci davinci da850_am18xxevm arm arm926ejs da8xxevm davinci davinci da850evm:DA850_AM18X_EVM,MAC_ADDR_IN_EEPROM,SYS_I2C_EEPROM_ADDR_LEN=2,SYS_I2C_EEPROM_ADDR=0x50 da850evm arm arm926ejs da8xxevm davinci davinci da850evm:MAC_ADDR_IN_SPIFLASH diff --git a/include/configs/ipam390.h b/include/configs/ipam390.h new file mode 100644 index 0000000..82d4298 --- /dev/null +++ b/include/configs/ipam390.h @@ -0,0 +1,331 @@ +/* + * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. + * Based on: + * U-Boot:include/configs/da850evm.h + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on davinci_dvevm.h. Original Copyrights follow: + * + * Copyright (C) 2007 Sergey Kubushyn ksi@koi8.net + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Board + */ +#define CONFIG_DRIVER_TI_EMAC +#define CONFIG_BARIX_IPAM390 + +/* + * SoC Configuration + */ +#define CONFIG_MACH_DAVINCI_DA850_EVM +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SOC_DA850 /* TI DA850 SoC */ +#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) +#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_DA850_PLL_INIT +#define CONFIG_SYS_DA850_DDR_INIT +#define CONFIG_SYS_TEXT_BASE 0xc1080000 + +/* + * Memory Info + */ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ +#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */ +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ + +/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) + +/* memtest will be run on 16MB */ +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 16 * 1024 * 1024) + +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ + +#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ + DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ + DAVINCI_SYSCFG_SUSPSRC_UART2 | \ + DAVINCI_SYSCFG_SUSPSRC_UART0 | \ + DAVINCI_SYSCFG_SUSPSRC_EMAC) + +/* + * PLL configuration + */ +#define CONFIG_SYS_DV_CLKMODE 0 +#define CONFIG_SYS_DA850_PLL0_POSTDIV 1 +#define CONFIG_SYS_DA850_PLL0_PLLDIV1 0x8000 +#define CONFIG_SYS_DA850_PLL0_PLLDIV2 0x8001 +#define CONFIG_SYS_DA850_PLL0_PLLDIV3 0x8002 +#define CONFIG_SYS_DA850_PLL0_PLLDIV4 0x8003 +#define CONFIG_SYS_DA850_PLL0_PLLDIV5 0x8002 +#define CONFIG_SYS_DA850_PLL0_PLLDIV6 CONFIG_SYS_DA850_PLL0_PLLDIV1 +#define CONFIG_SYS_DA850_PLL0_PLLDIV7 0x8005 + +#define CONFIG_SYS_DA850_PLL1_POSTDIV 1 +#define CONFIG_SYS_DA850_PLL1_PLLDIV1 0x8000 +#define CONFIG_SYS_DA850_PLL1_PLLDIV2 0x8001 +#define CONFIG_SYS_DA850_PLL1_PLLDIV3 0x8002 + +#define CONFIG_SYS_DA850_PLL0_PLLM 24 +#define CONFIG_SYS_DA850_PLL1_PLLM 24 + +/* + * DDR2 memory configuration + */ +#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ + DV_DDR_PHY_EXT_STRBEN | \ + (0x2 << DV_DDR_PHY_RD_LATENCY_SHIFT)) +#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000498 + +#define CONFIG_SYS_DA850_DDR2_SDBCR2 0x00000004 +#define CONFIG_SYS_DA850_DDR2_PBBPR 0x00000020 + + +#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ + (13 << DV_DDR_SDTMR1_RFC_SHIFT) | \ + (2 << DV_DDR_SDTMR1_RP_SHIFT) | \ + (2 << DV_DDR_SDTMR1_RCD_SHIFT) | \ + (2 << DV_DDR_SDTMR1_WR_SHIFT) | \ + (5 << DV_DDR_SDTMR1_RAS_SHIFT) | \ + (8 << DV_DDR_SDTMR1_RC_SHIFT) | \ + (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ + (1 << DV_DDR_SDTMR1_WTR_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ + (8 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ + (2 << DV_DDR_SDTMR2_XP_SHIFT) | \ + (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ + (14 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ + (0xc7 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ + (1 << DV_DDR_SDTMR2_RTP_SHIFT) | \ + (2 << DV_DDR_SDTMR2_CKE_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDBCR ( \ + (1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \ + (1 << DV_DDR_SDCR_DDRDRIVE0_SHIFT) | \ + (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ + (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ + (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ + (2 << DV_DDR_SDCR_CL_SHIFT) | \ + (3 << DV_DDR_SDCR_IBANK_SHIFT) | \ + (2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) + +#define CONFIG_SYS_DA850_CS3CFG (DAVINCI_ABCR_WSETUP(2) | \ + DAVINCI_ABCR_WSTROBE(2) | \ + DAVINCI_ABCR_WHOLD(1) | \ + DAVINCI_ABCR_RSETUP(1) | \ + DAVINCI_ABCR_RSTROBE(4) | \ + DAVINCI_ABCR_RHOLD(0) | \ + DAVINCI_ABCR_TA(1) | \ + DAVINCI_ABCR_ASIZE_8BIT) + + +/* + * Serial Driver info + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART0_BASE /* Base address of UART0 */ +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ + +/* + * Flash & Environment + */ +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_PAGE_2K +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_SYS_NAND_MASK_CLE 0x10 +#define CONFIG_SYS_NAND_MASK_ALE 0x8 +#undef CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x120000 +#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000 +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \ + CONFIG_SYS_NAND_U_BOOT_SIZE - \ + CONFIG_SYS_MALLOC_LEN - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_NAND_ECCPOS { \ + 24, 25, 26, 27, 28, \ + 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \ + 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \ + 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \ + 59, 60, 61, 62, 63 } +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 10 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_NAND_SIMPLE +#define CONFIG_SPL_NAND_LOAD + +/* + * Network & Ethernet Configuration + */ +#ifdef CONFIG_DRIVER_TI_EMAC +#define CONFIG_DRIVER_TI_EMAC_USE_RMII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#endif + +/* + * U-Boot general configuration + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CONFIG_SYS_PROMPT "U-Boot > " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* + * Linux Information + */ +#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) +#define CONFIG_HWCONFIG /* enable hwconfig */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_REVISION_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS \ + "mem=128M console=ttyS0,115200n8 root=/dev/mtdblock0p4 rw noinitrd ip=dhcp" +#define CONFIG_BOOTDELAY 3 +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=dsp:wake=yes\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "setbootparms=nand read c0100000 200000 400000;" \ + "spl export atags c0100000;" \ + "nand erase.part bootparms;" \ + "nand write c0000100 180000 20000\0" \ + "\0" + +/* + * U-Boot commands + */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MEMORY + +#ifdef CONFIG_CMD_BDI +#define CONFIG_CLOCKS +#endif + +#ifndef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_MII +#undef CONFIG_CMD_PING +#endif + +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NAND_TRIMFFS + +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_LZO +#define CONFIG_RBTREE +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS + +#define MTDIDS_NAME_STR "davinci_nand.0" +#define MTDIDS_DEFAULT "nand0=" MTDIDS_NAME_STR +#define MTDPARTS_DEFAULT "mtdparts=" MTDIDS_NAME_STR ":" \ + "128k(u-boot-env)," \ + "1408k(u-boot)," \ + "128k(bootparms)," \ + "384k(factory-info)," \ + "4M(kernel)," \ + "-(rootfs)" + +/* defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ + CONFIG_SYS_MALLOC_LEN) +#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-ipam390.lds" +#define CONFIG_SPL_STACK 0x8001ff00 +#define CONFIG_SPL_TEXT_BASE 0x80000000 +#define CONFIG_SPL_MAX_SIZE 0x20000 +#define CONFIG_SPL_MAX_FOOTPRINT 32768 + +/* additions for new relocation code, must added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0xc0000000 + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) + +/* add FALCON boot mode */ +#define CONFIG_CMD_SPL +#define CONFIG_SPL_OS_BOOT +#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 +#define CONFIG_SYS_SPL_ARGS_ADDR LINUX_BOOT_PARAM_ADDR +#define CONFIG_CMD_SPL_NAND_OFS 0x00180000 +#define CONFIG_CMD_SPL_WRITE_SIZE 0x400 + +/* GPIO support */ +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_DA8XX_GPIO +#define CONFIG_IPAM390_GPIO_BOOTMODE ((16 * 7) + 14) + +#define CONFIG_SHOW_BOOT_PROGRESS +#define CONFIG_IPAM390_GPIO_LED_RED ((16 * 7) + 11) +#define CONFIG_IPAM390_GPIO_LED_GREEN ((16 * 7) + 12) + +#endif /* __CONFIG_H */