This patch supports P1021MDS NAND boot with the following features: * Boot from NAND flash with SRAM BOOT support.(No NOR flash on this board) * SPD DDR Initialization

Signed-off-by: Haiying Wang Haiying.Wang@freescale.com Signed-off-by: Mohit Kumar Mohit.Kumar@freescale.com Signed-off-by: Yu.Liu Yu.Liu@freescale.com --- MAKEALL | 1 + Makefile | 4 + board/freescale/p1021mds/Makefile | 38 ++ board/freescale/p1021mds/bcsr.c | 22 + board/freescale/p1021mds/bcsr.h | 18 + board/freescale/p1021mds/config.mk | 24 ++ board/freescale/p1021mds/ddr.c | 148 +++++++ board/freescale/p1021mds/law.c | 24 ++ board/freescale/p1021mds/p1021mds.c | 122 ++++++ board/freescale/p1021mds/pci.c | 91 +++++ board/freescale/p1021mds/tlb.c | 72 ++++ include/configs/P1021MDS.h | 536 +++++++++++++++++++++++++ nand_spl/board/freescale/p1021mds/Makefile | 117 ++++++ nand_spl/board/freescale/p1021mds/nand_boot.c | 59 +++ 14 files changed, 1276 insertions(+), 0 deletions(-) create mode 100644 board/freescale/p1021mds/Makefile create mode 100644 board/freescale/p1021mds/bcsr.c create mode 100644 board/freescale/p1021mds/bcsr.h create mode 100644 board/freescale/p1021mds/config.mk create mode 100644 board/freescale/p1021mds/ddr.c create mode 100644 board/freescale/p1021mds/law.c create mode 100644 board/freescale/p1021mds/p1021mds.c create mode 100644 board/freescale/p1021mds/pci.c create mode 100644 board/freescale/p1021mds/tlb.c create mode 100644 include/configs/P1021MDS.h create mode 100644 nand_spl/board/freescale/p1021mds/Makefile create mode 100644 nand_spl/board/freescale/p1021mds/nand_boot.c

diff --git a/MAKEALL b/MAKEALL index b34ae33..f14c955 100755 --- a/MAKEALL +++ b/MAKEALL @@ -428,6 +428,7 @@ LIST_85xx=" \ P2020RDB_NAND \ P2020RDB_SDCARD \ P2020RDB_SPIFLASH \ + P1021MDS_NAND \ P4080DS \ PM854 \ PM856 \ diff --git a/Makefile b/Makefile index b1d92b7..7bfa733 100644 --- a/Makefile +++ b/Makefile @@ -1809,6 +1809,10 @@ P2020RDB_SDCARD_config \ P2020RDB_SPIFLASH_config: unconfig @$(MKCONFIG) -n $@ -t $@ P1_P2_RDB powerpc mpc85xx p1_p2_rdb freescale

+P1021MDS_config \ +P1021MDS_NAND_config: unconfig + @$(MKCONFIG) -n $@ -t $@ P1021MDS powerpc mpc85xx p1021mds freescale + sbc8540_config \ sbc8540_33_config \ sbc8540_66_config: unconfig diff --git a/board/freescale/p1021mds/Makefile b/board/freescale/p1021mds/Makefile new file mode 100644 index 0000000..bb744f0 --- /dev/null +++ b/board/freescale/p1021mds/Makefile @@ -0,0 +1,38 @@ +# +# Copyright (C) 2010 Freescale Semiconductor, Inc. +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o +COBJS-y += bcsr.o +COBJS-y += law.o +COBJS-y += tlb.o +COBJS-y += pci.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1021mds/bcsr.c b/board/freescale/p1021mds/bcsr.c new file mode 100644 index 0000000..6daf690 --- /dev/null +++ b/board/freescale/p1021mds/bcsr.c @@ -0,0 +1,22 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + */ + +#include <common.h> +#include <asm/io.h> + +#include "bcsr.h" + +#define BCSR11_ENET_MICRST 0x20 + +void reset_p1021mds_micrel_phy(void) +{ + clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 11), BCSR11_ENET_MICRST); + setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 11), BCSR11_ENET_MICRST); +} diff --git a/board/freescale/p1021mds/bcsr.h b/board/freescale/p1021mds/bcsr.h new file mode 100644 index 0000000..f3e47d4 --- /dev/null +++ b/board/freescale/p1021mds/bcsr.h @@ -0,0 +1,18 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + */ + +#ifndef __BCSR_H_ +#define __BCSR_H_ + +#include <common.h> + +/*BCSR Utils functions*/ +void reset_p1021mds_micrel_phy(void); +#endif /* __BCSR_H_ */ diff --git a/board/freescale/p1021mds/config.mk b/board/freescale/p1021mds/config.mk new file mode 100644 index 0000000..b2019d3 --- /dev/null +++ b/board/freescale/p1021mds/config.mk @@ -0,0 +1,24 @@ +# +# Copyright (C) 2010 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# +# p1021mds board +# + +ifdef SRAM_BOOT +TEXT_BASE := 0xf8f81000 +PAD_TO := 0xf8f8c000 +endif + +ifndef NAND_SPL +ifeq ($(CONFIG_MK_NAND), y) +ifndef SRAM_BOOT +TEXT_BASE = $(CONFIG_RAMBOOT_TEXT_BASE) +LDSCRIPT := $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds +endif +endif +endif diff --git a/board/freescale/p1021mds/ddr.c b/board/freescale/p1021mds/ddr.c new file mode 100644 index 0000000..0efa9bb --- /dev/null +++ b/board/freescale/p1021mds/ddr.c @@ -0,0 +1,148 @@ +/* + * Copyright 2009 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <i2c.h> +#include <asm/processor.h> +#include <asm/io.h> +#include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +DECLARE_GLOBAL_DATA_PTR; + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd, unsigned int ctrl_num) +{ + int ret; + + /* + * The P1021 only has one DDR controller, and the P1021MDS board has + * only one DIMM slot. + */ + + ret = i2c_read(SPD_EEPROM_ADDRESS1, 0, 1, (u8 *)ctrl_dimms_spd, + sizeof(ddr3_spd_eeprom_t)); + + if (ret) { + debug("DDR: failed to read SPD from address %u\n", + SPD_EEPROM_ADDRESS1); + memset(ctrl_dimms_spd, 0, sizeof(ddr3_spd_eeprom_t)); + } +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * Factors to consider for clock adjust: + */ + popts->clk_adjust = 6; + + /* + * Factors to consider for CPO: + */ + popts->cpo_override = 0x1f; + + /* + * Factors to consider for write data delay: + */ + popts->write_data_delay = 2; + + /* + * Factors to consider for half-strength driver enable: + */ + popts->half_strength_driver_enable = 1; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 1; + popts->rtt_override_value = DDR3_RTT_40_OHM; /* 40 Ohm rtt */ + popts->rtt_wr_override_value = 2; /* Rtt_WR */ + + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xa; + popts->wrlvl_start = 0x8; + /* + * P1021 supports max 32-bit DDR width + */ + popts->data_bus_width = 1; + + /* + * disable on-the-fly burst chop mode for 32 bit data bus + */ + popts->OTF_burst_chop_en = 0; + + /* + * Set fixed 8 beat burst for 32 bit data bus + */ + popts->burst_length = DDR_BL8; +} + +phys_size_t fixed_sdram(void) +{ + ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR; + u32 temp_sdram_cfg; + + set_next_law(0 , LAW_SIZE_512M , LAW_TRGT_IF_DDR_1); + + out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); + out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); + out_be32(&ddr->cs0_config_2, CONFIG_SYS_DDR_CS0_CONFIG_2); + out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL_2); + out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL); + out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL); + out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT); + out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1); + out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_1); + out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); + out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); + out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); + out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); + out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_SDRAM_MODE); + out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_SDRAM_MODE_2); + out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_SDRAM_INTERVAL); + out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL); + out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4); + out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); + out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | SDRAM_CFG_32_BE); + + sync(); + isync(); + + udelay(500); + + /* Let the controller go */ + temp_sdram_cfg = in_be32(&ddr->sdram_cfg); + out_be32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN); + + return 512 * 1024 * 1024; +} + +phys_size_t init_ddr_dram(void) +{ + phys_size_t dram_size = 0; +#ifdef CONFIG_SPD_EEPROM + dram_size = fsl_ddr_sdram(); +#else + dram_size = fixed_sdram(); +#endif + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts("\n DDR: "); + return dram_size; +} diff --git a/board/freescale/p1021mds/law.c b/board/freescale/p1021mds/law.c new file mode 100644 index 0000000..bb9d92e --- /dev/null +++ b/board/freescale/p1021mds/law.c @@ -0,0 +1,24 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_1), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_1), + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_2), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_2), + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256K, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1021mds/p1021mds.c b/board/freescale/p1021mds/p1021mds.c new file mode 100644 index 0000000..c61c902 --- /dev/null +++ b/board/freescale/p1021mds/p1021mds.c @@ -0,0 +1,122 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <hwconfig.h> +#include <pci.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <asm/mp.h> +#include <i2c.h> +#include <ioports.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <fsl_esdhc.h> +#include <tsec.h> +#include <netdev.h> + +const char *board_hwconfig = "foo:bar=baz"; +const char *cpu_hwconfig = "foo:bar=baz"; + +int board_early_init_f(void) +{ + + fsl_lbc_t *lbc = LBC_BASE_ADDR; + +#ifdef CONFIG_MMC + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + setbits_be32(&gur->pmuxcr, + (MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP)); +#endif + + /* Set ABSWP to implement conversion of addresses in the LBC */ + setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR); + + return 0; +} + +int checkboard(void) +{ + printf("Board: P1021 MDS\n"); + + return 0; +} + +phys_size_t initdram(int board_type) +{ + return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; +} + +#ifdef CONFIG_TSEC_ENET +int board_eth_init(bd_t *bis) +{ + struct tsec_info_struct tsec_info[3]; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif + +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + num++; +#endif + +#ifdef CONFIG_TSEC3 + SET_STD_TSEC_INFO(tsec_info[num], 3); + if (!(in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_SGMII3_DIS)) + tsec_info[num].flags |= TSEC_SGMII; + num++; +#endif + + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + tsec_eth_init(bis, tsec_info, num); + + return pci_eth_init(bis); +} +#endif + +#if defined(CONFIG_OF_BOARD_SETUP) +extern void ft_pci_board_setup(void *blob); + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, base, size); + + ft_pci_board_setup(blob); + +} +#endif +; +#ifdef CONFIG_MP +extern void cpu_mp_lmb_reserve(struct lmb *lmb); + +void board_lmb_reserve(struct lmb *lmb) +{ + cpu_mp_lmb_reserve(lmb); +} +#endif diff --git a/board/freescale/p1021mds/pci.c b/board/freescale/p1021mds/pci.c new file mode 100644 index 0000000..2a19ae5 --- /dev/null +++ b/board/freescale/p1021mds/pci.c @@ -0,0 +1,91 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <hwconfig.h> +#include <pci.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <libfdt.h> +#include <fdt_support.h> + +#ifdef CONFIG_PCIE1 +static struct pci_controller pcie1_hose; +#endif /* CONFIG_PCIE1 */ +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif /* CONFIG_PCIE2 */ + +void pci_init_board(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + struct fsl_pci_info pci_info[2]; + u32 devdisr, pordevsr, io_sel; + int first_free_busno = 0; + int num = 0; + + int pcie_ep, pcie_configured; + + devdisr = in_be32(&gur->devdisr); + pordevsr = in_be32(&gur->pordevsr); + io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19; + + debug(" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel); + + if (!(pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS)) + printf(" eTSEC2 is in sgmii mode.\n"); + if (!(pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS)) + printf(" eTSEC3 is in sgmii mode.\n"); + + puts("\n"); +#ifdef CONFIG_PCIE1 + pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel); + + if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)) { + SET_STD_PCIE_INFO(pci_info[num], 1); + pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs); + printf(" PCIE1 connected to Slot as %s (base addr %lx)\n", + pcie_ep ? "End Point" : "Root Complex", + pci_info[num].regs); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie1_hose, first_free_busno); + } else { + printf(" PCIE1: disabled\n"); + } + puts("\n"); +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE); /* disable */ +#endif /* CONFIG_PCIE1 */ + +#ifdef CONFIG_PCIE2 + pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_2, io_sel); + + if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE2)) { + SET_STD_PCIE_INFO(pci_info[num], 2); + pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs); + printf(" PCIE2 connected to Slot as %s (base addr %lx)\n", + pcie_ep ? "End Point" : "Root Complex", + pci_info[num].regs); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie2_hose, first_free_busno); + + } else { + printf(" PCIE2: disabled\n"); + } + puts("\n"); +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE2); /* disable */ +#endif /* CONFIG_PCIE2 */ +} + +void ft_pci_board_setup(void *blob) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/p1021mds/tlb.c b/board/freescale/p1021mds/tlb.c new file mode 100644 index 0000000..66ec22a --- /dev/null +++ b/board/freescale/p1021mds/tlb.c @@ -0,0 +1,72 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - PCIE */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCIE I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_IO_VIRT, CONFIG_SYS_PCIE2_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_256K, 1), + + /* *I*G - NAND */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1M, 1), + + /* + * *I*G BCSR/PMC0/PMC1 + */ + SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256K, 1), + +#if defined(CONFIG_NAND_SPL) || defined(CONFIG_SRAM_BOOT) + /* *I*G - L2SRAM */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 7, BOOKE_PAGESZ_256K, 1) +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/include/configs/P1021MDS.h b/include/configs/P1021MDS.h new file mode 100644 index 0000000..6f63aac --- /dev/null +++ b/include/configs/P1021MDS.h @@ -0,0 +1,536 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + */ + +/* + * p1021mds board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx /* MPC8540/60/55/41/48/68/P1021 */ +#define CONFIG_P1021 /* P1021 silicon support */ +#define CONFIG_P1021MDS /* P1021MDS board specific */ +#define CONFIG_MP /* Multiprocessor support */ + +#define CONFIG_FSL_ELBC /* Has Enhance localbus controller */ + +#define CONFIG_PCI /* Disable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controller */ +#define CONFIG_PCIE2 /* PCIE controller */ +#define CONFIG_FSL_PCI_INIT /* use common fsl pci init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_TSEC_ENET /* tsec ethernet support */ + +#ifdef CONFIG_MK_NAND +#define CONFIG_NAND_U_BOOT +#define CONFIG_MIDDLE_STAGE_SRAM_BOOT +#define CONFIG_RAMBOOT_NAND +#define CONFIG_RAMBOOT_TEXT_BASE 0x01001000 +#endif + +/* Replace a call to get_clock_freq (after it is implemented)*/ +#define CONFIG_SYS_CLK_FREQ 66666666 +#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ +#define CONFIG_HWCONFIG + +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x1fffffff + +#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of + addresses in the LBC */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR + /* physical addr of CCSRBAR */ +#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR +#else +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#endif +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR + /* PQII uses CONFIG_SYS_IMMR */ + +/* DDR Setup */ +#define CONFIG_FSL_DDR3 +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_SPD + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 + /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ + +/* These are used when DDR doesn't use SPD. */ +#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 +#define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 +#define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 +#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 +#define CONFIG_SYS_DDR_WRLVL_CNTL 0x86559608 +#define CONFIG_SYS_DDR_CDR_1 0x000eaa00 +#define CONFIG_SYS_DDR_CDR_2 0x00000000 +#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 +#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 +#define CONFIG_SYS_DDR_CONTROL 0x470c0000 /* Type = DDR3 */ +#define CONFIG_SYS_DDR_CONTROL_2 0x04401050 +#define CONFIG_SYS_DDR_DATA_INIT 0x1021babe +#define CONFIG_SYS_DDR_TIMING_3 0x00010000 +#define CONFIG_SYS_DDR_TIMING_0 0x00330004 +#define CONFIG_SYS_DDR_TIMING_1 0x5d5bd746 +#define CONFIG_SYS_DDR_TIMING_2 0x0fa8c8cd +#define CONFIG_SYS_DDR_SDRAM_MODE 0x40461320 +#define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 +#define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x0a280000 +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x03000000 +#define CONFIG_SYS_DDR_TIMING_4 0x00220001 +#define CONFIG_SYS_DDR_TIMING_5 0x03402400 + +#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 +#define CONFIG_SYS_DDR_SBE 0x00010000 + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Config the L2 Cache as L2 SRAM + */ +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) + + +/* + * Memory map + * + * 0x0000_0000 0x1fff_ffff DDR3 512MB cacheable + * 0xa000_0000 0xbfff_ffff PCIE2 Mem 512MB non-cacheable + * 0xc000_0000 0xdfff_ffff PCIE1 Mem 512MB non-cacheable + * 0xffc1_0000 0xffc1_ffff PCIE2 IO range 64K non-cacheable + * 0xffc2_0000 0xffc2_ffff PCIE1 IO range 64K non-cacheable + * 0xf800_0000 0xf800_7fff BCSR on CS1 32KB non-cacheable + * 0xf801_0000 0xf801_ffff PMC1 on CS2 64KB non-cacheable + * 0xf802_0000 0xf802_ffff PMC0 on CS3 64KB non-cacheable + * 0xfc00_0000 0xfdff_ffff NAND on CS0 32MB non-cacheable + * 0xffe0_0000 0xffef_ffff CCSRBAR 1M + */ + + +/* + * Local Bus Definitions + */ + +#define CONFIG_SYS_BCSR_BASE 0xf8000000 +#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE + +#define CONFIG_SYS_PIB_PMC1_BASE 0xf8010000 + /* start of PIB-QOC3(PMC1) 64K */ +#define CONFIG_SYS_PIB_PMC1_BASE_PHYS CONFIG_SYS_PIB_PMC1_BASE + +#define CONFIG_SYS_PIB_PMC0_BASE 0xf8020000 + /* start of PIB-T1/E1(PMC0) 64K */ +#define CONFIG_SYS_PIB_PMC0_BASE_PHYS CONFIG_SYS_PIB_PMC0_BASE + +/* chip select 1 - BCSR*/ +#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +/* chip select 2 - PIB(QOC3-PMC1)*/ +#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC1_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR2_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +/* chip select 3 - PIB(T1/E1-PMC0)*/ +#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC0_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR3_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_NO_FLASH + +#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) \ + || defined(CONFIG_RAMBOOT_SPIFLASH) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_NAND_BASE 0xFFF00000 +#else +#define CONFIG_SYS_NAND_BASE 0xFC000000 +#endif +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) + +/* NAND boot: 4K NAND loader config */ +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_NAND_SPL_SIZE 0x1000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE (48 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) +#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) +#endif +#ifdef CONFIG_SRAM_BOOT +/* Sram boot: 48K middle stage uboot config*/ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x01000000) +#define CONFIG_SYS_NAND_U_BOOT_START (0x01000000) +#define CONFIG_SYS_NAND_U_BOOT_OFFS (64 << 10) +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + \ + (128 << 10)) +#endif + +/* NAND FLASH CONFIG */ +#define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) +/* chip select 0 - NAND */ +#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SERIAL_MULTI +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) +#ifdef CONFIG_NAND_SPL +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif + +/* Use the HUSH parser*/ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +#define CONFIG_SYS_64BIT_VSPRINTF +#define CONFIG_SYS_64BIT_STRTOUL + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* TSEC support */ +#if defined(CONFIG_TSEC_ENET) + +/* TSECV2 */ +#define CONFIG_TSECV2 + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI +#endif + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 0 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHYIDX 0 + +#define TSEC2_PHY_ADDR 4 +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_SGMII) +#define TSEC2_PHYIDX 0 + +#ifdef CONFIG_TSEC3_IN_SGMII /* Need to set SW8.6 to 0 */ +#define TSEC3_PHY_ADDR 6 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_SGMII) +#else +#define TSEC3_PHY_ADDR 1 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#endif +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif /* CONFIG_TSEC_ENET */ + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0, 0x69}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#ifdef CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#endif +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +#define PLPPAR1_I2C_BIT_MASK 0x0000000F +#define PLPPAR1_I2C2_VAL 0x00000000 +#define PLPPAR1_ESDHC_VAL 0x0000000A +#define PLPDIR1_I2C_BIT_MASK 0x0000000F +#define PLPDIR1_I2C2_VAL 0x0000000F +#define PLPDIR1_ESDHC_VAL 0x00000006 + +/* + * General PCI + * Memory Addresses are mapped 1-1. I/O is mapped from 0 + */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64K */ + +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ + +#if defined(CONFIG_PCI) +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#endif + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (576 * 1024) +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ + +#define CONFIG_MMC +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) + /* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_HOSTNAME p1021mds +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_BOOTFILE your.uImage + +#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=your.ramdisk.u-boot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=your.fdt.dtb\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + "ramargs=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + +#define CONFIG_NFSBOOTCOMMAND \ + "run nfsargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "run ramargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr $ramdiskaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ diff --git a/nand_spl/board/freescale/p1021mds/Makefile b/nand_spl/board/freescale/p1021mds/Makefile new file mode 100644 index 0000000..2e88d72 --- /dev/null +++ b/nand_spl/board/freescale/p1021mds/Makefile @@ -0,0 +1,117 @@ +# +# Copyright (C) 2010 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# + +NAND_SPL := y +TEXT_BASE := 0xfff00000 +PAD_TO := 0xfff04000 + +include $(TOPDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-nand_spl.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_NAND_SPL + +SOBJS = start.o resetvec.o +COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \ + nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +nandobj := $(OBJTREE)/nand_spl/ + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin + +all: $(obj).depend $(ALL) + +$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +# create symbolic links for common files + +$(obj)cache.c: + @rm -f $(obj)cache.c + ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c + +$(obj)cpu_init_early.c: + @rm -f $(obj)cpu_init_early.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_early.c $(obj)cpu_init_early.c + +$(obj)cpu_init_nand.c: + @rm -f $(obj)cpu_init_nand.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c $(obj)cpu_init_nand.c + +$(obj)fsl_law.c: + @rm -f $(obj)fsl_law.c + ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c + +$(obj)law.c: + @rm -f $(obj)law.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c + +$(obj)nand_boot_fsl_elbc.c: + @rm -f $(obj)nand_boot_fsl_elbc.c + ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \ + $(obj)nand_boot_fsl_elbc.c + +$(obj)ns16550.c: + @rm -f $(obj)ns16550.c + ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c + +$(obj)resetvec.S: + @rm -f $(obj)resetvec.S + ln -s $(SRCTREE)/arch/powerpc/cpu/$(CPU)/resetvec.S $(obj)resetvec.S + +$(obj)fixed_ivor.S: + @rm -f $(obj)fixed_ivor.S + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/fixed_ivor.S $(obj)fixed_ivor.S + +$(obj)start.S: $(obj)fixed_ivor.S + @rm -f $(obj)start.S + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/start.S $(obj)start.S + +$(obj)tlb.c: + @rm -f $(obj)tlb.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/tlb.c $(obj)tlb.c + +$(obj)tlb_table.c: + @rm -f $(obj)tlb_table.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c + +ifneq ($(OBJTREE), $(SRCTREE)) +$(obj)nand_boot.c: + @rm -f $(obj)nand_boot.c + ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c +endif + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/freescale/p1021mds/nand_boot.c b/nand_spl/board/freescale/p1021mds/nand_boot.c new file mode 100644 index 0000000..18898a9 --- /dev/null +++ b/nand_spl/board/freescale/p1021mds/nand_boot.c @@ -0,0 +1,59 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + */ +#include <common.h> +#include <mpc85xx.h> +#include <asm/io.h> +#include <ns16550.h> +#include <nand.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> + +DECLARE_GLOBAL_DATA_PTR; + +void board_init_f(ulong bootflag) +{ + uint plat_ratio, bus_clk, sys_clk = 0; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + sys_clk = CONFIG_SYS_CLK_FREQ; + + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + bus_clk = plat_ratio * sys_clk; + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + /* copy code to DDR and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0, + CONFIG_SYS_NAND_U_BOOT_RELOC); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +}