This patch adds support for the kmeter1 board from Keymile, based on a Freescale MPC8360 CPU.

- serial console on UART 1 - 256 MB DDR2 RAM - 64 MB NOR Flash - Ethernet RMII Mode over UCC4 - PHY SMSC LAN8700

Signed-off-by: Heiko Schocher hs@denx.de ---

changes since v2:

added comments from Kim Philips added doc/README.kmeter1

MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 + board/keymile/kmeter1/Makefile | 51 ++++ board/keymile/kmeter1/config.mk | 24 ++ board/keymile/kmeter1/kmeter1.c | 153 ++++++++++++ doc/README.kmeter1 | 91 +++++++ include/configs/kmeter1.h | 523 +++++++++++++++++++++++++++++++++++++++ 8 files changed, 847 insertions(+), 0 deletions(-) create mode 100644 board/keymile/kmeter1/Makefile create mode 100644 board/keymile/kmeter1/config.mk create mode 100644 board/keymile/kmeter1/kmeter1.c create mode 100644 doc/README.kmeter1 create mode 100644 include/configs/kmeter1.h

diff --git a/MAINTAINERS b/MAINTAINERS index 127604b..4086831 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -374,6 +374,7 @@ Heiko Schocher hs@denx.de

ids8247 MPC8247 jupiter MPC5200 + kmeter1 MPC8360 mgcoge MPC8247 mgsuvd MPC852 mucmc52 MPC5200 diff --git a/MAKEALL b/MAKEALL index dbed268..a4e38ce 100755 --- a/MAKEALL +++ b/MAKEALL @@ -326,6 +326,7 @@ LIST_8260=" \ #########################################################################

LIST_83xx=" \ + kmeter1 \ MPC8313ERDB_33 \ MPC8313ERDB_NAND_66 \ MPC8315ERDB \ diff --git a/Makefile b/Makefile index fd521b6..1fe8f70 100644 --- a/Makefile +++ b/Makefile @@ -2175,6 +2175,9 @@ TASREG_config : unconfig ## MPC83xx Systems #########################################################################

+kmeter1_config: unconfig + @$(MKCONFIG) kmeter1 ppc mpc83xx kmeter1 keymile + MPC8313ERDB_33_config \ MPC8313ERDB_66_config \ MPC8313ERDB_NAND_33_config \ diff --git a/board/keymile/kmeter1/Makefile b/board/keymile/kmeter1/Makefile new file mode 100644 index 0000000..88b79f3 --- /dev/null +++ b/board/keymile/kmeter1/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o + +COBJS := $(COBJS-y) +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/keymile/kmeter1/config.mk b/board/keymile/kmeter1/config.mk new file mode 100644 index 0000000..20f298b --- /dev/null +++ b/board/keymile/kmeter1/config.mk @@ -0,0 +1,24 @@ +# +# (C) Copyright 2008 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +TEXT_BASE = 0xF0000000 diff --git a/board/keymile/kmeter1/kmeter1.c b/board/keymile/kmeter1/kmeter1.c new file mode 100644 index 0000000..f9a59a6 --- /dev/null +++ b/board/keymile/kmeter1/kmeter1.c @@ -0,0 +1,153 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * Dave Liu daveliu@freescale.com + * + * Copyright (C) 2007 Logic Product Development, Inc. + * Peter Barada peterb@logicpd.com + * + * Copyright (C) 2007 MontaVista Software, Inc. + * Anton Vorontsov avorontsov@ru.mvista.com + * + * (C) Copyright 2008 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include <common.h> +#include <ioports.h> +#include <mpc83xx.h> +#include <i2c.h> +#include <miiphy.h> +#include <asm/io.h> +#include <asm/mmu.h> +#include <pci.h> +#include <libfdt.h> + +const qe_iop_conf_t qe_iop_conf_tab[] = { + /* port pin dir open_drain assign */ + + /* MDIO */ + {0, 1, 3, 0, 2}, /* MDIO */ + {0, 2, 1, 0, 1}, /* MDC */ + + /* UCC4 - UEC */ + {1, 14, 1, 0, 1}, /* TxD0 */ + {1, 15, 1, 0, 1}, /* TxD1 */ + {1, 20, 2, 0, 1}, /* RxD0 */ + {1, 21, 2, 0, 1}, /* RxD1 */ + {1, 18, 1, 0, 1}, /* TX_EN */ + {1, 26, 2, 0, 1}, /* RX_DV */ + {1, 27, 2, 0, 1}, /* RX_ER */ + {1, 24, 2, 0, 1}, /* COL */ + {1, 25, 2, 0, 1}, /* CRS */ + {2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */ + {2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */ + + /* DUART - UART2 */ + {5, 0, 1, 0, 2}, /* UART2_SOUT */ + {5, 2, 1, 0, 1}, /* UART2_RTS */ + {5, 3, 2, 0, 2}, /* UART2_SIN */ + {5, 1, 2, 0, 3}, /* UART2_CTS */ + + /* END of table */ + {0, 0, 0, 0, QE_IOP_TAB_END}, +}; + +int board_early_init_r (void) +{ + void *reg = (void *)(CONFIG_SYS_IMMR + 0x14a8); + u32 val; + + /* + * Because of errata in the UCCs, we have to write to the reserved + * registers to slow the clocks down. + */ + val = in_be32 (reg); + /* UCC1 */ + val |= 0x00003000; + /* UCC2 */ + val |= 0x0c000000; + out_be32 (reg, val); + /* enable the PHY on the PIGGY */ + setbits (8, (void *)(CONFIG_SYS_PIGGY_BASE + 0x10003), 0x01); + + return 0; +} + +int fixed_sdram(void) +{ + volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR; + u32 msize = 0; + u32 ddr_size; + u32 ddr_size_log2; + + msize = CONFIG_SYS_DDR_SIZE; + for (ddr_size = msize << 20, ddr_size_log2 = 0; + (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) { + if (ddr_size & 1) + return -1; + } + + im->sysconf.ddrlaw[0].ar = + LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE); + + im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS; + im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG; + im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0; + im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2; + im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3; + im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG; + im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2; + im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE; + im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2; + im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL; + im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL; + udelay (200); + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + + return msize; +} + +phys_size_t initdram (int board_type) +{ +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) + extern void ddr_enable_ecc (unsigned int dram_size); +#endif + volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR; + u32 msize = 0; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im) + return -1; + + /* DDR SDRAM - Main SODIMM */ + im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR; + msize = fixed_sdram (); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) + /* + * Initialize DDR ECC byte + */ + ddr_enable_ecc (msize * 1024 * 1024); +#endif + + /* return total bus SDRAM size(bytes) -- DDR */ + return (msize * 1024 * 1024); +} + +int checkboard (void) +{ + puts ("Board: Keymile kmeter1\n"); + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup (void *blob, bd_t *bd) +{ + ft_cpu_setup (blob, bd); +} +#endif diff --git a/doc/README.kmeter1 b/doc/README.kmeter1 new file mode 100644 index 0000000..44ebb7a --- /dev/null +++ b/doc/README.kmeter1 @@ -0,0 +1,91 @@ +Keymile kmeter1 Board +----------------------------------------- +1. Alternative Boot EEPROM + + Upon the kmeter1 startup the I2C_1 controller is used to fetch the boot + configuration from a serial EEPROM. During the development and debugging + phase it might be helpful to apply an alternative boot configuration in + a simple way. Therefore it is an alternative boot eeprom on the PIGGY, + which can be activated by setting the "ST" jumper on the PIGGY board. + +2. Memory Map + + BaseAddr PortSz Size Device + ----------- ------ ----- ------ + 0x0000_0000 64 bit 256MB DDR + 0x8000_0000 8 bit 256KB GPIO/PIGGY on CS1 + 0xa000_0000 8 bit 256MB PAXE on CS3 + 0xe000_0000 2MB Int Mem Reg Space + 0xf000_0000 16 bit 256MB FLASH on CS0 + + + DDR-SDRAM: + The current realization is made with four 16-bits memory devices. + Mounting options have been foreseen for device architectures from + 4Mx16 to 512Mx16. The kmeter1 is equipped with four 32Mx16 devices + thus resulting in a total capacity of 256MBytes. + +3. Compilation + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + make kmeter1_config + make + +4. Downloading and Flashing Images + +4.0 Download over serial line using Kermit: + + loadb + [Drop to kermit: + ^\c + send <u-boot-bin-image> + c + ] + + + Or via tftp: + + tftp 10000 u-boot.bin + => run load + Using FSL UEC0 device + TFTP from server 192.168.1.1; our IP address is 192.168.205.4 + Filename '/tftpboot/kmeter1/u-boot.bin'. + Load address: 0x200000 + Loading: ############## + done + Bytes transferred = 204204 (31dac hex) + => + +4.1 Reflash U-boot Image using U-boot + + => run update + ..... done + Un-Protected 5 sectors + + ..... done + Erased 5 sectors + Copy to Flash... done + ..... done + Protected 5 sectors + Total of 204204 bytes were the same + Saving Environment to Flash... + . done + Un-Protected 1 sectors + . done + Un-Protected 1 sectors + Erasing Flash... + . done + Erased 1 sectors + Writing to Flash... done + . done + Protected 1 sectors + . done + Protected 1 sectors + => + +5. Notes + 1) The console baudrate for kmeter1 is 115200bps. diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h new file mode 100644 index 0000000..bca1b9b --- /dev/null +++ b/include/configs/kmeter1.h @@ -0,0 +1,523 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * Dave Liu daveliu@freescale.com + * + * Copyright (C) 2007 Logic Product Development, Inc. + * Peter Barada peterb@logicpd.com + * + * Copyright (C) 2007 MontaVista Software, Inc. + * Anton Vorontsov avorontsov@ru.mvista.com + * + * (C) Copyright 2008 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ +#define CONFIG_MPC83XX 1 /* MPC83XX family */ +#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ +#define CONFIG_KMETER1 1 /* KMETER1 board specific */ + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 66000000 +#define CONFIG_SYS_CLK_FREQ 66000000 +#define CONFIG_83XX_PCICLK 66000000 + +/* + * Hardware Reset Configuration Word + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_CSB_TO_CLKIN_4X1 | \ + HRCWL_CORE_TO_CSB_2X1 | \ + HRCWL_CE_PLL_VCO_DIV_2 | \ + HRCWL_CE_TO_PLL_1X6 ) + +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_CORE_ENABLE | \ + HRCWH_FROM_0X00000100 | \ + HRCWH_BOOTSEQ_NORMAL | \ + HRCWH_SW_WATCHDOG_DISABLE | \ + HRCWH_ROM_LOC_LOCAL_16BIT | \ + HRCWH_BIG_ENDIAN | \ + HRCWH_LDP_CLEAR ) + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH 0x00000006 +#define CONFIG_SYS_SICRL 0x00000000 + +#define CONFIG_BOARD_EARLY_INIT_R + +/* + * IMMR new address + */ +#define CONFIG_SYS_IMMR 0xE0000000 + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ + DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) + +#define CFG_83XX_DDR_USES_CS0 + +#undef CONFIG_DDR_ECC + +/* + * DDRCDR - DDR Control Driver Register + */ + +#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ + +/* + * Manually set up DDR parameters + */ +#define CONFIG_DDR_II +#define CONFIG_SYS_DDR_SIZE 256 /* MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ + CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS) + +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_SREN) +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((0x100 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x406 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_MODE 0x04440242 +#define CONFIG_SYS_DDR_MODE2 0x00800000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_40) | \ + ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \ + ( 1 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + ( 2 << TIMING_CFG1_WRREC_SHIFT) | \ + ( 2 << TIMING_CFG1_REFREC_SHIFT) | \ + ( 2 << TIMING_CFG1_ACTTORW_SHIFT) | \ + ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + ( 2 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((5 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (4 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +/* + * Memory test + */ +#define CONFIG_SYS_ALT_MEMTEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00F00000 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_FLASH_BASE 0xF0000000 +#define CONFIG_SYS_FLASH_BASE_1 0xF2000000 +#define CONFIG_SYS_PIGGY_BASE 0x80000000 +#define CONFIG_SYS_PAXE_BASE 0xA0000000 +#define CONFIG_SYS_PAXE_SIZE 256 + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_2 | LCRR_CLKDIV_4) + +/* + * Init Local Bus Memory Controller: + * + * Bank Bus Machine PortSz Size Device + * ---- --- ------- ------ ----- ------ + * 0 Local GPCM 16 bit 256MB FLASH + * 1 Local GPCM 8 bit 256KB GPIO/PIGGY + * 3 Local GPCM 8 bit 256MB PAXE + * + */ +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 + +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001b /* 256MB window size */ + +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ + BR_V) + +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ + OR_GPCM_SCY_5 | \ + OR_GPCM_TRLX | OR_GPCM_EAD) + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_1 } + +#undef CONFIG_SYS_FLASH_CHECKSUM + +/* + * PRIO1/PIGGY on the local bus CS1 + */ +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE /* Window base at flash base */ +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x80000011 /* 256KB window size */ + +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE | \ + (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ + BR_V) +#define CONFIG_SYS_OR1_PRELIM (0xfffc0000 | /* 256KB */ \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ + OR_GPCM_SCY_2 | \ + OR_GPCM_TRLX | OR_GPCM_EAD) + +/* + * PAXE on the local bus CS3 + */ +#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PAXE_BASE /* Window base at flash base */ +#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001b /* 256MB window size */ + +#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_PAXE_BASE | \ + (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ + BR_V) +#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ + OR_GPCM_SCY_2 | \ + OR_GPCM_TRLX | OR_GPCM_EAD) + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200,} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#undef CONFIG_PCI /* No PCI */ + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH +#define CONFIG_ETHPRIME "FSL UEC0" + +#define CONFIG_UEC_ETH1 /* GETH1 */ +#define UEC_VERBOSE_DEBUG 1 + +#ifdef CONFIG_UEC_ETH1 +#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 +#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 0 +#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII +#endif + +/* + * Environment + */ + +#ifndef CONFIG_SYS_RAMBOOT +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#else /* CFG_RAMBOOT */ +#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ +#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ +#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_SIZE 0x2000 +#endif /* CFG_RAMBOOT */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#endif + +#if defined(CFG_RAMBOOT) +#undef CONFIG_CMD_ENV +#undef CONFIG_CMD_LOADS +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +#define CONFIG_SYS_HZ 1000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CONFIG_SYS_HID2 HID2_HBE + +/* + * MMU Setup + */ + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* DDR: cache cacheable */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* IMMRBAR & PCI IO: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_256K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) +#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U + +/* PAXE: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U + +#ifdef CONFIG_PCI +/* PCI MEM space: cacheable */ +#define CFG_IBAT6L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT6U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +/* PCI MMIO space: cache-inhibit and guarded */ +#define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#else /* CONFIG_PCI */ +#define CONFIG_SYS_IBAT6L (0) +#define CONFIG_SYS_IBAT6U (0) +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U +#endif /* CONFIG_PCI */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "rootpath=/opt/eldk/ppc_82xx\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs}" \ + " console=ttyS0,${baudrate}\0" \ + "fdt_addr=f0080000\0" \ + "kernel_addr=f00a0000\0" \ + "ramdisk_addr=f03a0000\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=800000\0" \ + "ramdisk_addr_r=810000\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${boot_file}; " \ + "tftp ${fdt_addr_r} ${fdt_file}; " \ + "run nfsargs addip addtty;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "fdt_file=/tftpboot/kmeter1/kmeter1.dtb\0" \ + "boot_file=/tftpboot/kmeter1/uImage\0" \ + "ramdisk_file=/tftpboot/kmeter1/uRamdisk\0" \ + "u-boot=/tftpboot/kmeter1/u-boot.bin\0" \ + "loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0" \ + "load=tftp $loadaddr ${u-boot}\0" \ + "update=protect off " MK_STR(TEXT_BASE) " +$filesize;" \ + "erase " MK_STR(TEXT_BASE) " +$filesize;" \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \ + "protect on " MK_STR(TEXT_BASE) " +$filesize;" \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \ + "setenv filesize;saveenv\0" \ + "upd=run load update\0" \ + "loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0" \ + "loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0" \ + "loadkernel=tftp ${kernel_addr_r} ${boot_file}\0" \ + "unlock=yes\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run net_nfs" + +#endif /* __CONFIG_H */