[U-Boot] [PATCH] sun7i: Add new Bananapro board / defconfig
Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede hdegoede@redhat.com --- board/sunxi/Kconfig | 4 ++++ board/sunxi/Makefile | 1 + board/sunxi/gmac.c | 2 +- configs/Bananapro_defconfig | 9 +++++++++ 4 files changed, 15 insertions(+), 1 deletion(-) create mode 100644 configs/Bananapro_defconfig
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index 0cbfb26..8782394 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -97,6 +97,10 @@ config TARGET_BANANAPI bool "BANANAPI" depends on MACH_SUN7I
+config TARGET_BANANAPRO + bool "BANANAPRO" + depends on MACH_SUN7I + config TARGET_COLOMBUS bool "COLOMBUS" depends on MACH_SUN6I diff --git a/board/sunxi/Makefile b/board/sunxi/Makefile index 97aff10..8ca01f6 100644 --- a/board/sunxi/Makefile +++ b/board/sunxi/Makefile @@ -22,6 +22,7 @@ obj-$(CONFIG_TARGET_A20_OLINUXINO_M) += dram_sun7i_384_1024_iow16.o obj-$(CONFIG_TARGET_AUXTEK_T004) += dram_a10s_olinuxino_m.o obj-$(CONFIG_TARGET_BA10_TV_BOX) += dram_sun4i_384_1024_iow8.o obj-$(CONFIG_TARGET_BANANAPI) += dram_bananapi.o +obj-$(CONFIG_TARGET_BANANAPRO) += dram_bananapi.o obj-$(CONFIG_TARGET_CUBIEBOARD) += dram_cubieboard.o obj-$(CONFIG_TARGET_CUBIEBOARD2) += dram_cubieboard2.o obj-$(CONFIG_TARGET_CUBIETRUCK) += dram_cubietruck.o diff --git a/board/sunxi/gmac.c b/board/sunxi/gmac.c index 571bc9e..4e4615e 100644 --- a/board/sunxi/gmac.c +++ b/board/sunxi/gmac.c @@ -34,7 +34,7 @@ int sunxi_gmac_initialize(bd_t *bis) * need to set bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" * of the GMAC clk register to 3. */ -#ifdef CONFIG_TARGET_BANANAPI +#if defined CONFIG_TARGET_BANANAPI || defined CONFIG_TARGET_BANANAPRO setbits_le32(&ccm->gmac_clk_cfg, 0x3 << 10); #endif
diff --git a/configs/Bananapro_defconfig b/configs/Bananapro_defconfig new file mode 100644 index 0000000..7f9ce13 --- /dev/null +++ b/configs/Bananapro_defconfig @@ -0,0 +1,9 @@ +CONFIG_SPL=y +CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI" +CONFIG_FDTFILE="sun7i-a20-bananapro.dtb" +CONFIG_USB1_VBUS_PIN="PH0" +CONFIG_USB2_VBUS_PIN="PH1" ++S:CONFIG_ARM=y ++S:CONFIG_ARCH_SUNXI=y ++S:CONFIG_MACH_SUN7I=y ++S:CONFIG_TARGET_BANANAPRO=y
On Wed, 2014-12-31 at 11:38 +0100, Hans de Goede wrote:
Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede hdegoede@redhat.com
Acked-by: Ian Campbell ijc@hellion.org.uk
-#ifdef CONFIG_TARGET_BANANAPI +#if defined CONFIG_TARGET_BANANAPI || defined CONFIG_TARGET_BANANAPRO setbits_le32(&ccm->gmac_clk_cfg, 0x3 << 10);
Did we ever get to the bottom of what this was?
I take it that you've confirmed it is needed for the pro, rather than just carrying it over?
Ian.
Hi,
On 31-12-14 11:42, Ian Campbell wrote:
On Wed, 2014-12-31 at 11:38 +0100, Hans de Goede wrote:
Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede hdegoede@redhat.com
Acked-by: Ian Campbell ijc@hellion.org.uk
-#ifdef CONFIG_TARGET_BANANAPI +#if defined CONFIG_TARGET_BANANAPI || defined CONFIG_TARGET_BANANAPRO setbits_le32(&ccm->gmac_clk_cfg, 0x3 << 10);
Did we ever get to the bottom of what this was?
Yes it sets the TX clock delay chain, which is something which one typically need to do for RGMII phy-s, why this is not needed on the cubietruck is not known / clear.
I take it that you've confirmed it is needed for the pro, rather than just carrying it over?
I've not tested the gmac myself yet, but this is being done by their own u-boot port for the pro in their lemaker github account.
Regards,
Hans
Hi,
On 31-12-14 11:42, Ian Campbell wrote:
On Wed, 2014-12-31 at 11:38 +0100, Hans de Goede wrote:
Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede hdegoede@redhat.com
Acked-by: Ian Campbell ijc@hellion.org.uk
Thanks, I've rebased u-boot-sunxi/next to the latest master, squashed the sun6i m / k pll5 fix into the original commit as you suggested, added this patch and done a forced push with the result.
If you plan to add Jan Kiszka's patches to next (which I think is a good idea), please base them on top of what I've just pushed.
Thanks & Regards,
Hans
participants (2)
-
Hans de Goede -
Ian Campbell