po 9. 12. 2019 v 15:58 odesílatel Michal Simek michal.simek@xilinx.com napsal:

In past SPL_ZYNQMP_TWO_SDHCI symbol was introduced to handle boards with two sdhci controllers. The problem was that U-Boot is registering controllers based on aliases in DT but bootmode targets specific controller ID. That's why on boards with one "second" sdhci controller bootmode was pointing to second controller(MMC2) but alias was setup to mmc0 (the first controller). And SPL requires to point to mmc0 in this case.

Long time ago commit f101e4bd3703 ("spl: add support for alternative boot device") added support for handling multiple bootmodes in SPL. Use this functionality and setup second sdhci controller as backup boot device.

Below is table with behavior: HW/bootmode bootorder sd0/sd0 mmc0/mmc1 (mmc1 never called) sd1/sd1 mmc1/mmc0 (mmc0 fails and mmc1 is called) sd0+sd1/sd0 mmc0/mmc1 (mmc1 never called) sd0+sd1/sd1 mmc1/mmc0 (mmc0 never called)

All other bootmodes are not affected but order can be extended to cover advance boot flows.

Signed-off-by: Michal Simek michal.simek@xilinx.com

arch/arm/mach-zynqmp/Kconfig | 11 ----------- arch/arm/mach-zynqmp/spl.c | 14 ++++++++++---- ...ltrazedev_cc_v1_0_ultrazedev_som_v1_0_defconfig | 1 - configs/xilinx_zynqmp_p_a2197_00_revA_defconfig | 1 - configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 - 5 files changed, 10 insertions(+), 18 deletions(-)

diff --git a/arch/arm/mach-zynqmp/Kconfig b/arch/arm/mach-zynqmp/Kconfig index 6cf17eb94e11..d82a737a699e 100644 --- a/arch/arm/mach-zynqmp/Kconfig +++ b/arch/arm/mach-zynqmp/Kconfig @@ -117,17 +117,6 @@ config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED config ZYNQ_SDHCI_MAX_FREQ default 200000000

-config SPL_ZYNQMP_TWO_SDHCI

•   bool "Enable booting from both SDHCIs"
  

•   depends on SPL
  

•   help
  

•     This option reflects that board has two SDHCI controllers which
  

•     platform can use as boot device. This option ensures that SPL will
  

•     setup BOOT_DEVICE_MMC2 for SDHCI1 controller and BOOT_DEVICE_MMC1 for
  

•     SDHCI0 controller. Platforms which have only one SDHCI controller
  

•     shouldn't enable this option because it for software SDHCI0 or SDHCI1
  

•     are both covered by BOOT_DEVICE_MMC1.
  

config SPL_ZYNQMP_ALT_BOOTMODE hex default 0x0 if JTAG_MODE diff --git a/arch/arm/mach-zynqmp/spl.c b/arch/arm/mach-zynqmp/spl.c index 8bb1cdf69e1b..37f690d9b958 100644 --- a/arch/arm/mach-zynqmp/spl.c +++ b/arch/arm/mach-zynqmp/spl.c @@ -65,6 +65,16 @@ void spl_board_init(void) } #endif

+void board_boot_order(u32 *spl_boot_list) +{

•   spl_boot_list[0] = spl_boot_device();
  

•   if (spl_boot_list[0] == BOOT_DEVICE_MMC1)
  

•           spl_boot_list[1] = BOOT_DEVICE_MMC2;
  

•   if (spl_boot_list[0] == BOOT_DEVICE_MMC2)
  

•           spl_boot_list[1] = BOOT_DEVICE_MMC1;
  

+}

u32 spl_boot_device(void) { u32 reg = 0; @@ -88,11 +98,7 @@ u32 spl_boot_device(void) #ifdef CONFIG_SPL_MMC_SUPPORT case SD_MODE1: case SD1_LSHFT_MODE: /* not working on silicon v1 */ -/* if both controllers enabled, then these two are the second controller */ -#ifdef CONFIG_SPL_ZYNQMP_TWO_SDHCI return BOOT_DEVICE_MMC2; -/* else, fall through, the one SDHCI controller that is enabled is number 1 */ -#endif case SD_MODE: case EMMC_MODE: return BOOT_DEVICE_MMC1; diff --git a/configs/avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0_defconfig b/configs/avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0_defconfig index 177558db4198..280983d187a1 100644 --- a/configs/avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0_defconfig +++ b/configs/avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0_defconfig @@ -7,7 +7,6 @@ CONFIG_DEBUG_UART_BASE=0xff000000 CONFIG_DEBUG_UART_CLOCK=100000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_ZYNQMP_TWO_SDHCI=y CONFIG_DEBUG_UART=y CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y diff --git a/configs/xilinx_zynqmp_p_a2197_00_revA_defconfig b/configs/xilinx_zynqmp_p_a2197_00_revA_defconfig index ba2cbaba58e9..f206be8a3145 100644 --- a/configs/xilinx_zynqmp_p_a2197_00_revA_defconfig +++ b/configs/xilinx_zynqmp_p_a2197_00_revA_defconfig @@ -9,7 +9,6 @@ CONFIG_IDENT_STRING=" Xilinx ZynqMP SC for Versal" CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_ZYNQMP_USB=y -CONFIG_SPL_ZYNQMP_TWO_SDHCI=y CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y diff --git a/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig b/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig index 65ce1ff2d337..c7524f630788 100644 --- a/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig +++ b/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig @@ -7,7 +7,6 @@ CONFIG_DEBUG_UART_BASE=0xff000000 CONFIG_DEBUG_UART_CLOCK=100000000 CONFIG_PMUFW_INIT_FILE="/mnt/disk/u-boot-bins/zynqmp/zynqmp-zc1751-xm015-dc1/pmufw.bin" CONFIG_ZYNQMP_USB=y -CONFIG_SPL_ZYNQMP_TWO_SDHCI=y CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y -- 2.24.0

Applied. M