[PATCH v3 0/6] rockchip: Update stack and bss addresses on RK3308, RK3328, RK3399, RK356x and RK3588
Trying to run U-Boot proper close to 1 MiB in size with debug logging something similar to following can be observed:
FDT 00000000002fc4e0 gd 00000000002fddf0 FDT overlap resetting ... System reset not supported on this platform ### ERROR ### Please RESET the board ###
Fix this by changing stack and bss addresses used on RK3328 and RK3399. The addresses chosen for stack and bss is a combination from both boards.
In v3 the implementation is changed to introduce a new Kconfig flag that will help set default addresses and sizes that prevent code, heap and stack from overlapping, see first patch for more details.
Other Rockchip aarch64 SoCs can also be migrated to use these defaults. However, I only have devices using these SoCs to test and verify on.
TEXT_BASE for U-Boot proper can be changed to start at 0x200000 (2 M) for migrated SoCs, I however opted to keep the existing TEXT_BASE used on each migrated SoC.
The malloc heap sizes chosen is almost double of what current affected SoCs are using. RK35xx was using an unusual large malloc heap for pre-reloc, so these was reduced to use more sane values. There should be plenty of room to increase bss and malloc heap sizes without risk of overlapping if there is ever any need for that in the future.
Four RK3399 boards have been left untouched because they use SRAM for SPL stack: - chromebook_bob_defconfig - chromebook_kevin_defconfig - ficus-rk3399_defconfig - puma-rk3399_defconfig
The following steps have been performed to migrate SoCs and boards to use the common bss and stack addresses.
In SoC Kconfig: - Add ROCKCHIP_COMMON_STACK_ADDR - Set TPL malloc heap size - Set custom TEXT_BASE to use for SoC - Remove defaults any of the Kconfig options that now have default values defined
In board defconfig: - Enable CONFIG_SPL_SHARES_INIT_SP_ADDR - Remove any of the Kconfig options that now have default values defined - Refresh defconfig using make savedefconfig (or using qconfig.py) - Verify using a clean build of U-Boot
Changes in v3: - Rework to use a new Kconfig option to enable use of common bss and stack addresses. - Migrate RK3308, RK356x and RK3588 in addition to RK3328 and RK3399 - Drop r-b tags because of major changes
Changes in v2: - Rebase on v2 of "rockchip: rk3328: Update defconfigs, DTs and enable boot from SPI" [1] - Use correct address 0x04000000 for 64 MiB offset in commit message - Collect r-b tag
The RK3328 patch in this series depends on v2 of the following two series: - rockchip: rk3328: Update defconfigs, DTs and enable boot from SPI [1] - rockchip: Read cpuid and generate MAC address from efuse for RK3328 and RK3399 [2]
A copy of this series and its two depends can be found at [3].
[1] https://patchwork.ozlabs.org/cover/1900345/ [2] https://patchwork.ozlabs.org/cover/1897743/ [3] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3xxx-stack-v3
Jonas Karlman (6): rockchip: Add common default bss and stack addresses rockchip: Use common bss and stack addresses on RK3308 rockchip: Use common bss and stack addresses on RK3328 rockchip: Use common bss and stack addresses on RK3399 rockchip: Use common bss and stack addresses on RK356x rockchip: Use common bss and stack addresses on RK3588
Kconfig | 2 +- arch/arm/mach-rockchip/Kconfig | 55 +++++++++++++++++++ arch/arm/mach-rockchip/rk3308/Kconfig | 7 ++- arch/arm/mach-rockchip/rk3328/Kconfig | 11 ++-- arch/arm/mach-rockchip/rk3399/Kconfig | 7 ++- arch/arm/mach-rockchip/rk3568/Kconfig | 7 ++- arch/arm/mach-rockchip/rk3588/Kconfig | 7 ++- configs/anbernic-rgxx3-rk3566_defconfig | 13 ----- configs/bpi-r2-pro-rk3568_defconfig | 13 ----- configs/eaidk-610-rk3399_defconfig | 10 ---- configs/evb-rk3308_defconfig | 13 ----- configs/evb-rk3328_defconfig | 17 ------ configs/evb-rk3399_defconfig | 10 ---- configs/evb-rk3568_defconfig | 13 ----- configs/evb-rk3588_defconfig | 13 ----- configs/firefly-rk3399_defconfig | 10 ---- configs/generic-rk3568_defconfig | 13 ----- configs/khadas-edge-captain-rk3399_defconfig | 10 ---- configs/khadas-edge-rk3399_defconfig | 10 ---- configs/khadas-edge-v-rk3399_defconfig | 10 ---- configs/leez-rk3399_defconfig | 10 ---- configs/lubancat-2-rk3568_defconfig | 13 ----- configs/nanopc-t4-rk3399_defconfig | 10 ---- configs/nanopc-t6-rk3588_defconfig | 13 ----- configs/nanopi-m4-2gb-rk3399_defconfig | 10 ---- configs/nanopi-m4-rk3399_defconfig | 10 ---- configs/nanopi-m4b-rk3399_defconfig | 10 ---- configs/nanopi-neo4-rk3399_defconfig | 10 ---- configs/nanopi-r2c-plus-rk3328_defconfig | 15 ----- configs/nanopi-r2c-rk3328_defconfig | 15 ----- configs/nanopi-r2s-rk3328_defconfig | 15 ----- configs/nanopi-r4s-rk3399_defconfig | 10 ---- configs/nanopi-r5c-rk3568_defconfig | 13 ----- configs/nanopi-r5s-rk3568_defconfig | 13 ----- configs/neu6a-io-rk3588_defconfig | 13 ----- configs/neu6b-io-rk3588_defconfig | 13 ----- configs/odroid-m1-rk3568_defconfig | 13 ----- configs/orangepi-5-plus-rk3588_defconfig | 13 ----- configs/orangepi-5-rk3588s_defconfig | 13 ----- configs/orangepi-r1-plus-lts-rk3328_defconfig | 15 ----- configs/orangepi-r1-plus-rk3328_defconfig | 15 ----- configs/orangepi-rk3399_defconfig | 10 ---- configs/pinebook-pro-rk3399_defconfig | 10 ---- configs/pinephone-pro-rk3399_defconfig | 10 ---- configs/quartz64-a-rk3566_defconfig | 13 ----- configs/quartz64-b-rk3566_defconfig | 13 ----- configs/quartzpro64-rk3588_defconfig | 13 ----- configs/radxa-cm3-io-rk3566_defconfig | 13 ----- configs/radxa-e25-rk3568_defconfig | 13 ----- configs/roc-cc-rk3308_defconfig | 13 ----- configs/roc-cc-rk3328_defconfig | 15 ----- configs/roc-pc-mezzanine-rk3399_defconfig | 10 ---- configs/roc-pc-rk3399_defconfig | 10 ---- configs/rock-3a-rk3568_defconfig | 13 ----- configs/rock-4c-plus-rk3399_defconfig | 10 ---- configs/rock-4se-rk3399_defconfig | 10 ---- configs/rock-pi-4-rk3399_defconfig | 10 ---- configs/rock-pi-4c-rk3399_defconfig | 10 ---- configs/rock-pi-e-rk3328_defconfig | 17 ------ configs/rock-pi-n10-rk3399pro_defconfig | 10 ---- configs/rock-pi-s-rk3308_defconfig | 13 ----- configs/rock5a-rk3588s_defconfig | 13 ----- configs/rock5b-rk3588_defconfig | 13 ----- configs/rock64-rk3328_defconfig | 15 ----- configs/rock960-rk3399_defconfig | 10 ---- configs/rockpro64-rk3399_defconfig | 10 ---- configs/soquartz-blade-rk3566_defconfig | 13 ----- configs/soquartz-cm4-rk3566_defconfig | 13 ----- configs/soquartz-model-a-rk3566_defconfig | 13 ----- configs/turing-rk1-rk3588_defconfig | 13 ----- 70 files changed, 80 insertions(+), 782 deletions(-)
On Rockchip the typical aarch64 boot steps are as follows: - BROM load TPL to SRAM - TPL init full DRAM - use stack in SRAM at TPL_STACK addr - use malloc heap on stack, size is TPL_SYS_MALLOC_F_LEN - TPL jump back to BROM - BROM load SPL to beginning of DRAM - SPL init storage devices - use bss in DRAM at SPL_BSS_START_ADDR, size is SPL_BSS_MAX_SIZE - use stack in DRAM at SPL_STACK addr (or CUSTOM_SYS_INIT_SP_ADDR) - use malloc heap on stack, size is SPL_SYS_MALLOC_F_LEN - SPL load FIT images from storage to DRAM - use stack in DRAM at SPL_STACK_R_ADDR - use new malloc heap on stack, size is SPL_STACK_R_MALLOC_SIMPLE_LEN - SPL jump to TF-A at 0x40000 - (optional) TF-A load OPTEE - TF-A jump to U-Boot proper at TEXT_BASE - U-Boot proper init pre-reloc devices - use stack in DRAM at CUSTOM_SYS_INIT_SP_ADDR - use malloc heap on stack, size is SYS_MALLOC_F_LEN - U-Boot proper relocate to end of usable DRAM - U-Boot proper init devices and complete boot
SPL have access to full DRAM, however, current configuration for text base, stack addr and malloc heap size used at the different boot steps are at risk of overlapping, e.g. when U-Boot proper + FDT grows close to 1 MiB on RK3328/RK3399 or when pre-reloc and reloc stack and malloc heap overlap on ROCK 5A.
Fix this by defining safe defaults for bss, stack and malloc size and addresses. A range at around [60 MiB, 64 MiB) was chosen to be used for bss and stack until U-Boot proper have been relocated to end of usable DRAM. The range was primarily chosen to be able to accommodate SoCs with a small amount of embedded DRAM, e.g. RK3308G has 64 MiB DRAM.
Overiew of the new common memory layout: [ 0, 2M) - SPL / TF-A / reserved [ 2M, +X) - U-Boot proper pre-reloc [ -X, 64M) - bss, stack and malloc heap
During SPL pre-reloc phase: [ 0, 256K) - SPL binary is loaded by BROM to beginning of DRAM [ -X, 63M) - SPL pre-reloc stack [ -32K, 63M) - SPL pre-reloc malloc heap [63.5M, +32K) - SPL bss
After SPL reloc phase: [ 0, 256K) - SPL binary [ 256K, +X) - TF-A image is loaded by SPL [ 2M, +X) - U-Boot proper + FDT image is loaded by SPL [ -X, 62M) - SPL reloc stack [ 60M, 62M) - SPL reloc malloc heap [ -32K, 63M) - SPL init malloc heap, memory allocated during SPL pre-reloc phase is still in use at reloc phase [63.5M, +32K) - SPL bss
During U-Boot proper pre-reloc phase: [ 0, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper + FDT [ -X, 63M) - U-Boot proper pre-reloc stack (shared addr with SPL) [ -64K, 63M) - U-Boot proper pre-reloc malloc heap
After U-Boot proper has relocated to top of memory we should be able to use 2M+ for loading kernel, initrd, scripts etc.
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- arch/arm/mach-rockchip/Kconfig | 55 ++++++++++++++++++++++++++++++++++ 1 file changed, 55 insertions(+)
diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig index 2c6b045c51c8..edbe3fd30853 100644 --- a/arch/arm/mach-rockchip/Kconfig +++ b/arch/arm/mach-rockchip/Kconfig @@ -534,6 +534,21 @@ config ROCKCHIP_SPI_IMAGE config LNX_KRNL_IMG_TEXT_OFFSET_BASE default TEXT_BASE
+config ROCKCHIP_COMMON_STACK_ADDR + bool + depends on SPL_SHARES_INIT_SP_ADDR + select HAS_CUSTOM_SYS_INIT_SP_ADDR + imply SPL_LIBCOMMON_SUPPORT if SPL + imply SPL_LIBGENERIC_SUPPORT if SPL + imply SPL_ROCKCHIP_COMMON_BOARD if SPL + imply SPL_SYS_MALLOC_F if SPL + imply SPL_SYS_MALLOC_SIMPLE if SPL + imply TPL_LIBCOMMON_SUPPORT if TPL + imply TPL_LIBGENERIC_SUPPORT if TPL + imply TPL_ROCKCHIP_COMMON_BOARD if TPL + imply TPL_SYS_MALLOC_F if TPL + imply TPL_SYS_MALLOC_SIMPLE if TPL + source "arch/arm/mach-rockchip/px30/Kconfig" source "arch/arm/mach-rockchip/rk3036/Kconfig" source "arch/arm/mach-rockchip/rk3066/Kconfig" @@ -549,4 +564,44 @@ source "arch/arm/mach-rockchip/rk3568/Kconfig" source "arch/arm/mach-rockchip/rk3588/Kconfig" source "arch/arm/mach-rockchip/rv1108/Kconfig" source "arch/arm/mach-rockchip/rv1126/Kconfig" + +if ROCKCHIP_COMMON_STACK_ADDR && SPL_SHARES_INIT_SP_ADDR + +config CUSTOM_SYS_INIT_SP_ADDR + default 0x3f00000 + +config SYS_MALLOC_F_LEN + default 0x10000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000 + +config SPL_SYS_MALLOC_F_LEN + default 0x8000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000 + +config TPL_SYS_MALLOC_F_LEN + default 0x4000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000 + +config TEXT_BASE + default 0x00200000 if ARM64 + +config SPL_TEXT_BASE + default 0x0 if ARM64 + +config SPL_HAS_BSS_LINKER_SECTION + default y if ARM64 + +config SPL_BSS_START_ADDR + default 0x3f80000 + +config SPL_BSS_MAX_SIZE + default 0x8000 if SPL_BSS_START_ADDR = 0x3f80000 + +config SPL_STACK_R + default y if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000 + +config SPL_STACK_R_ADDR + default 0x3e00000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000 + +config SPL_STACK_R_MALLOC_SIMPLE_LEN + default 0x200000 if SPL_STACK_R_ADDR = 0x3e00000 + +endif endif
Hi Jonas,
On 2024/3/3 03:16, Jonas Karlman wrote:
On Rockchip the typical aarch64 boot steps are as follows:
- BROM load TPL to SRAM
- TPL init full DRAM
- use stack in SRAM at TPL_STACK addr
- use malloc heap on stack, size is TPL_SYS_MALLOC_F_LEN
- TPL jump back to BROM
- BROM load SPL to beginning of DRAM
- SPL init storage devices
- use bss in DRAM at SPL_BSS_START_ADDR, size is SPL_BSS_MAX_SIZE
- use stack in DRAM at SPL_STACK addr (or CUSTOM_SYS_INIT_SP_ADDR)
- use malloc heap on stack, size is SPL_SYS_MALLOC_F_LEN
- SPL load FIT images from storage to DRAM
- use stack in DRAM at SPL_STACK_R_ADDR
- use new malloc heap on stack, size is SPL_STACK_R_MALLOC_SIMPLE_LEN
- SPL jump to TF-A at 0x40000
- (optional) TF-A load OPTEE
- TF-A jump to U-Boot proper at TEXT_BASE
- U-Boot proper init pre-reloc devices
- use stack in DRAM at CUSTOM_SYS_INIT_SP_ADDR
- use malloc heap on stack, size is SYS_MALLOC_F_LEN
- U-Boot proper relocate to end of usable DRAM
- U-Boot proper init devices and complete boot
SPL have access to full DRAM, however, current configuration for text base, stack addr and malloc heap size used at the different boot steps are at risk of overlapping, e.g. when U-Boot proper + FDT grows close to 1 MiB on RK3328/RK3399 or when pre-reloc and reloc stack and malloc heap overlap on ROCK 5A.
Fix this by defining safe defaults for bss, stack and malloc size and addresses. A range at around [60 MiB, 64 MiB) was chosen to be used for bss and stack until U-Boot proper have been relocated to end of usable DRAM. The range was primarily chosen to be able to accommodate SoCs with a small amount of embedded DRAM, e.g. RK3308G has 64 MiB DRAM.
Overiew of the new common memory layout: [ 0, 2M) - SPL / TF-A / reserved [ 2M, +X) - U-Boot proper pre-reloc [ -X, 64M) - bss, stack and malloc heap
During SPL pre-reloc phase: [ 0, 256K) - SPL binary is loaded by BROM to beginning of DRAM [ -X, 63M) - SPL pre-reloc stack [ -32K, 63M) - SPL pre-reloc malloc heap [63.5M, +32K) - SPL bss
After SPL reloc phase: [ 0, 256K) - SPL binary [ 256K, +X) - TF-A image is loaded by SPL [ 2M, +X) - U-Boot proper + FDT image is loaded by SPL [ -X, 62M) - SPL reloc stack [ 60M, 62M) - SPL reloc malloc heap [ -32K, 63M) - SPL init malloc heap, memory allocated during SPL pre-reloc phase is still in use at reloc phase [63.5M, +32K) - SPL bss
During U-Boot proper pre-reloc phase: [ 0, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper + FDT [ -X, 63M) - U-Boot proper pre-reloc stack (shared addr with SPL) [ -64K, 63M) - U-Boot proper pre-reloc malloc heap
After U-Boot proper has relocated to top of memory we should be able to use 2M+ for loading kernel, initrd, scripts etc.
Very good update and also good description here, can we also add the memory usage
description after update to rockchip.rst?
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
Signed-off-by: Jonas Karlman jonas@kwiboo.se
arch/arm/mach-rockchip/Kconfig | 55 ++++++++++++++++++++++++++++++++++ 1 file changed, 55 insertions(+)
diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig index 2c6b045c51c8..edbe3fd30853 100644 --- a/arch/arm/mach-rockchip/Kconfig +++ b/arch/arm/mach-rockchip/Kconfig @@ -534,6 +534,21 @@ config ROCKCHIP_SPI_IMAGE config LNX_KRNL_IMG_TEXT_OFFSET_BASE default TEXT_BASE
+config ROCKCHIP_COMMON_STACK_ADDR
- bool
- depends on SPL_SHARES_INIT_SP_ADDR
- select HAS_CUSTOM_SYS_INIT_SP_ADDR
- imply SPL_LIBCOMMON_SUPPORT if SPL
- imply SPL_LIBGENERIC_SUPPORT if SPL
- imply SPL_ROCKCHIP_COMMON_BOARD if SPL
- imply SPL_SYS_MALLOC_F if SPL
- imply SPL_SYS_MALLOC_SIMPLE if SPL
- imply TPL_LIBCOMMON_SUPPORT if TPL
- imply TPL_LIBGENERIC_SUPPORT if TPL
- imply TPL_ROCKCHIP_COMMON_BOARD if TPL
- imply TPL_SYS_MALLOC_F if TPL
- imply TPL_SYS_MALLOC_SIMPLE if TPL
- source "arch/arm/mach-rockchip/px30/Kconfig" source "arch/arm/mach-rockchip/rk3036/Kconfig" source "arch/arm/mach-rockchip/rk3066/Kconfig"
@@ -549,4 +564,44 @@ source "arch/arm/mach-rockchip/rk3568/Kconfig" source "arch/arm/mach-rockchip/rk3588/Kconfig" source "arch/arm/mach-rockchip/rv1108/Kconfig" source "arch/arm/mach-rockchip/rv1126/Kconfig"
+if ROCKCHIP_COMMON_STACK_ADDR && SPL_SHARES_INIT_SP_ADDR
+config CUSTOM_SYS_INIT_SP_ADDR
- default 0x3f00000
+config SYS_MALLOC_F_LEN
- default 0x10000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000
+config SPL_SYS_MALLOC_F_LEN
- default 0x8000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000
+config TPL_SYS_MALLOC_F_LEN
- default 0x4000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000
+config TEXT_BASE
- default 0x00200000 if ARM64
+config SPL_TEXT_BASE
- default 0x0 if ARM64
+config SPL_HAS_BSS_LINKER_SECTION
- default y if ARM64
+config SPL_BSS_START_ADDR
- default 0x3f80000
+config SPL_BSS_MAX_SIZE
- default 0x8000 if SPL_BSS_START_ADDR = 0x3f80000
+config SPL_STACK_R
- default y if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000
+config SPL_STACK_R_ADDR
- default 0x3e00000 if CUSTOM_SYS_INIT_SP_ADDR = 0x3f00000
+config SPL_STACK_R_MALLOC_SIMPLE_LEN
- default 0x200000 if SPL_STACK_R_ADDR = 0x3e00000
+endif endif
Currently the following memory layout is typically used on RK3308: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ 4M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE) [ 6M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 8M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -8K, 8M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 12M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 11M, 12M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
SPL can safely load U-Boot proper + FDT to [6M, 8M-8K) with this layout.
Migrate to use common bss, stack and malloc heap size and addresses to remove this size limitation and extend the malloc heap size being used.
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- Kconfig | 2 +- arch/arm/mach-rockchip/rk3308/Kconfig | 7 +++++-- configs/evb-rk3308_defconfig | 13 ------------- configs/roc-cc-rk3308_defconfig | 13 ------------- configs/rock-pi-s-rk3308_defconfig | 13 ------------- 5 files changed, 6 insertions(+), 42 deletions(-)
diff --git a/Kconfig b/Kconfig index 5710934000f6..75f9563ce6c6 100644 --- a/Kconfig +++ b/Kconfig @@ -265,7 +265,7 @@ config SYS_MALLOC_F_LEN hex "Size of malloc() pool before relocation" depends on SYS_MALLOC_F default 0x400 if M68K || PPC || ROCKCHIP_PX30 || ROCKCHIP_RK3036 || \ - ROCKCHIP_RK3308 || ROCKCHIP_RV1108 + ROCKCHIP_RV1108 default 0x600 if ARCH_ZYNQMP_R5 || ARCH_ZYNQMP default 0x800 if ARCH_ZYNQ || ROCKCHIP_RK3128 || ROCKCHIP_RK3188 || \ ROCKCHIP_RK322X || X86 diff --git a/arch/arm/mach-rockchip/rk3308/Kconfig b/arch/arm/mach-rockchip/rk3308/Kconfig index 194353e4cd9a..749e9995d91f 100644 --- a/arch/arm/mach-rockchip/rk3308/Kconfig +++ b/arch/arm/mach-rockchip/rk3308/Kconfig @@ -17,8 +17,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3308"
-config SYS_MALLOC_F_LEN - default 0x400 +config ROCKCHIP_COMMON_STACK_ADDR + default y + +config TEXT_BASE + default 0x00600000
config SPL_SERIAL default y diff --git a/configs/evb-rk3308_defconfig b/configs/evb-rk3308_defconfig index 2729060d6e91..d57b2f6b8e55 100644 --- a/configs/evb-rk3308_defconfig +++ b/configs/evb-rk3308_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00600000 -CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x800000 CONFIG_DEFAULT_DEVICE_TREE="rk3308-evb" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3308=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_TARGET_EVB_RK3308=y -CONFIG_SPL_STACK_R_ADDR=0xc00000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF0C0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,11 +20,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_ELF is not set diff --git a/configs/roc-cc-rk3308_defconfig b/configs/roc-cc-rk3308_defconfig index 7502da5b1e7a..5e8f51ec01e3 100644 --- a/configs/roc-cc-rk3308_defconfig +++ b/configs/roc-cc-rk3308_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00600000 -CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x800000 CONFIG_DEFAULT_DEVICE_TREE="rk3308-roc-cc" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3308=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_TARGET_ROC_RK3308_CC=y -CONFIG_SPL_STACK_R_ADDR=0xc00000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF0C0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,11 +20,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_ELF is not set diff --git a/configs/rock-pi-s-rk3308_defconfig b/configs/rock-pi-s-rk3308_defconfig index 9908a4b4f457..1e9cd2c0fc7e 100644 --- a/configs/rock-pi-s-rk3308_defconfig +++ b/configs/rock-pi-s-rk3308_defconfig @@ -2,20 +2,12 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00600000 -CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x800000 CONFIG_DEFAULT_DEVICE_TREE="rk3308-rock-pi-s" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3308=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_TARGET_EVB_RK3308=y -CONFIG_SPL_STACK_R_ADDR=0xc00000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF0A0000 CONFIG_DEBUG_UART_CLOCK=24000000 # CONFIG_DEBUG_UART_BOARD_INIT is not set @@ -29,11 +21,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_ELF is not set
On 2024/3/3 03:16, Jonas Karlman wrote:
Currently the following memory layout is typically used on RK3308: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ 4M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE) [ 6M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 8M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -8K, 8M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 12M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 11M, 12M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
SPL can safely load U-Boot proper + FDT to [6M, 8M-8K) with this layout.
Migrate to use common bss, stack and malloc heap size and addresses to remove this size limitation and extend the malloc heap size being used.
Signed-off-by: Jonas Karlman jonas@kwiboo.se
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
Kconfig | 2 +- arch/arm/mach-rockchip/rk3308/Kconfig | 7 +++++-- configs/evb-rk3308_defconfig | 13 ------------- configs/roc-cc-rk3308_defconfig | 13 ------------- configs/rock-pi-s-rk3308_defconfig | 13 ------------- 5 files changed, 6 insertions(+), 42 deletions(-)
diff --git a/Kconfig b/Kconfig index 5710934000f6..75f9563ce6c6 100644 --- a/Kconfig +++ b/Kconfig @@ -265,7 +265,7 @@ config SYS_MALLOC_F_LEN hex "Size of malloc() pool before relocation" depends on SYS_MALLOC_F default 0x400 if M68K || PPC || ROCKCHIP_PX30 || ROCKCHIP_RK3036 || \
ROCKCHIP_RK3308 || ROCKCHIP_RV1108
ROCKCHIP_RV1108diff --git a/arch/arm/mach-rockchip/rk3308/Kconfig b/arch/arm/mach-rockchip/rk3308/Kconfig index 194353e4cd9a..749e9995d91f 100644 --- a/arch/arm/mach-rockchip/rk3308/Kconfig +++ b/arch/arm/mach-rockchip/rk3308/Kconfig @@ -17,8 +17,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3308"
-config SYS_MALLOC_F_LEN
- default 0x400
+config ROCKCHIP_COMMON_STACK_ADDR
- default y
+config TEXT_BASE
default 0x00600000
config SPL_SERIAL default y
diff --git a/configs/evb-rk3308_defconfig b/configs/evb-rk3308_defconfig index 2729060d6e91..d57b2f6b8e55 100644 --- a/configs/evb-rk3308_defconfig +++ b/configs/evb-rk3308_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00600000 -CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x800000 CONFIG_DEFAULT_DEVICE_TREE="rk3308-evb" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3308=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_TARGET_EVB_RK3308=y -CONFIG_SPL_STACK_R_ADDR=0xc00000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF0C0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,11 +20,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_ELF is not set diff --git a/configs/roc-cc-rk3308_defconfig b/configs/roc-cc-rk3308_defconfig index 7502da5b1e7a..5e8f51ec01e3 100644 --- a/configs/roc-cc-rk3308_defconfig +++ b/configs/roc-cc-rk3308_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00600000 -CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x800000 CONFIG_DEFAULT_DEVICE_TREE="rk3308-roc-cc" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3308=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_TARGET_ROC_RK3308_CC=y -CONFIG_SPL_STACK_R_ADDR=0xc00000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF0C0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,11 +20,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_ELF is not set diff --git a/configs/rock-pi-s-rk3308_defconfig b/configs/rock-pi-s-rk3308_defconfig index 9908a4b4f457..1e9cd2c0fc7e 100644 --- a/configs/rock-pi-s-rk3308_defconfig +++ b/configs/rock-pi-s-rk3308_defconfig @@ -2,20 +2,12 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00600000 -CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x800000 CONFIG_DEFAULT_DEVICE_TREE="rk3308-rock-pi-s" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3308=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_TARGET_EVB_RK3308=y -CONFIG_SPL_STACK_R_ADDR=0xc00000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF0A0000 CONFIG_DEBUG_UART_CLOCK=24000000 # CONFIG_DEBUG_UART_BOARD_INIT is not set @@ -29,11 +21,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_ELF is not set
With the stack and text base used by U-Boot SPL and proper on RK3328 there is a high likelihood of overlapping when U-Boot proper + FDT nears or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3328: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -8K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 32M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [2M, 4M-8K) with this layout. However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- arch/arm/mach-rockchip/rk3328/Kconfig | 11 ++++------- configs/evb-rk3328_defconfig | 17 ----------------- configs/nanopi-r2c-plus-rk3328_defconfig | 15 --------------- configs/nanopi-r2c-rk3328_defconfig | 15 --------------- configs/nanopi-r2s-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-lts-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-rk3328_defconfig | 15 --------------- configs/roc-cc-rk3328_defconfig | 15 --------------- configs/rock-pi-e-rk3328_defconfig | 17 ----------------- configs/rock64-rk3328_defconfig | 15 --------------- 10 files changed, 4 insertions(+), 146 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3328/Kconfig b/arch/arm/mach-rockchip/rk3328/Kconfig index d5cb649ae6ba..70770da5fdf2 100644 --- a/arch/arm/mach-rockchip/rk3328/Kconfig +++ b/arch/arm/mach-rockchip/rk3328/Kconfig @@ -21,13 +21,7 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3328"
-config SYS_MALLOC_F_LEN - default 0x2000 - -config SPL_LIBCOMMON_SUPPORT - default y - -config SPL_LIBGENERIC_SUPPORT +config ROCKCHIP_COMMON_STACK_ADDR default y
config TPL_LDSCRIPT @@ -39,6 +33,9 @@ config TPL_TEXT_BASE config TPL_STACK default 0xff098000
+config TPL_SYS_MALLOC_F_LEN + default 0x800 + source "board/rockchip/evb_rk3328/Kconfig"
endif diff --git a/configs/evb-rk3328_defconfig b/configs/evb-rk3328_defconfig index da422c8ba4e7..4fa8a7d365a4 100644 --- a/configs/evb-rk3328_defconfig +++ b/configs/evb-rk3328_defconfig @@ -2,22 +2,12 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-evb" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x4000000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 -CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +23,9 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2c-plus-rk3328_defconfig b/configs/nanopi-r2c-plus-rk3328_defconfig index 25850328f8b8..5302fd91a0f5 100644 --- a/configs/nanopi-r2c-plus-rk3328_defconfig +++ b/configs/nanopi-r2c-plus-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c-plus" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2c-rk3328_defconfig b/configs/nanopi-r2c-rk3328_defconfig index a4cb148246e6..5a722c182631 100644 --- a/configs/nanopi-r2c-rk3328_defconfig +++ b/configs/nanopi-r2c-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2s-rk3328_defconfig b/configs/nanopi-r2s-rk3328_defconfig index c5d13788528b..985d02475ece 100644 --- a/configs/nanopi-r2s-rk3328_defconfig +++ b/configs/nanopi-r2s-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2s" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/orangepi-r1-plus-lts-rk3328_defconfig b/configs/orangepi-r1-plus-lts-rk3328_defconfig index 6360f5df3864..e9f7a1306923 100644 --- a/configs/orangepi-r1-plus-lts-rk3328_defconfig +++ b/configs/orangepi-r1-plus-lts-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus-lts" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus-lts.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/orangepi-r1-plus-rk3328_defconfig b/configs/orangepi-r1-plus-rk3328_defconfig index 9473a08fe20d..6019f33ae3f5 100644 --- a/configs/orangepi-r1-plus-rk3328_defconfig +++ b/configs/orangepi-r1-plus-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/roc-cc-rk3328_defconfig b/configs/roc-cc-rk3328_defconfig index c66b1ccba267..191dbff928bb 100644 --- a/configs/roc-cc-rk3328_defconfig +++ b/configs/roc-cc-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-roc-cc" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-roc-cc.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock-pi-e-rk3328_defconfig b/configs/rock-pi-e-rk3328_defconfig index 275ffc3ed8f4..e4f2123e0b17 100644 --- a/configs/rock-pi-e-rk3328_defconfig +++ b/configs/rock-pi-e-rk3328_defconfig @@ -2,23 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock-pi-e" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x4000000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 -CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -34,17 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock-pi-e.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock64-rk3328_defconfig b/configs/rock64-rk3328_defconfig index 1cb4e6777d45..f38431891bf8 100644 --- a/configs/rock64-rk3328_defconfig +++ b/configs/rock64-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock64" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock64.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y
On 2024/3/3 03:16, Jonas Karlman wrote:
With the stack and text base used by U-Boot SPL and proper on RK3328 there is a high likelihood of overlapping when U-Boot proper + FDT nears or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3328: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -8K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 32M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [2M, 4M-8K) with this layout. However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
arch/arm/mach-rockchip/rk3328/Kconfig | 11 ++++------- configs/evb-rk3328_defconfig | 17 ----------------- configs/nanopi-r2c-plus-rk3328_defconfig | 15 --------------- configs/nanopi-r2c-rk3328_defconfig | 15 --------------- configs/nanopi-r2s-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-lts-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-rk3328_defconfig | 15 --------------- configs/roc-cc-rk3328_defconfig | 15 --------------- configs/rock-pi-e-rk3328_defconfig | 17 ----------------- configs/rock64-rk3328_defconfig | 15 --------------- 10 files changed, 4 insertions(+), 146 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3328/Kconfig b/arch/arm/mach-rockchip/rk3328/Kconfig index d5cb649ae6ba..70770da5fdf2 100644 --- a/arch/arm/mach-rockchip/rk3328/Kconfig +++ b/arch/arm/mach-rockchip/rk3328/Kconfig @@ -21,13 +21,7 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3328"
-config SYS_MALLOC_F_LEN
- default 0x2000
-config SPL_LIBCOMMON_SUPPORT
- default y
-config SPL_LIBGENERIC_SUPPORT +config ROCKCHIP_COMMON_STACK_ADDR default y
config TPL_LDSCRIPT @@ -39,6 +33,9 @@ config TPL_TEXT_BASE config TPL_STACK default 0xff098000
+config TPL_SYS_MALLOC_F_LEN
default 0x800
source "board/rockchip/evb_rk3328/Kconfig"
endif
diff --git a/configs/evb-rk3328_defconfig b/configs/evb-rk3328_defconfig index da422c8ba4e7..4fa8a7d365a4 100644 --- a/configs/evb-rk3328_defconfig +++ b/configs/evb-rk3328_defconfig @@ -2,22 +2,12 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-evb" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x4000000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 -CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +23,9 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2c-plus-rk3328_defconfig b/configs/nanopi-r2c-plus-rk3328_defconfig index 25850328f8b8..5302fd91a0f5 100644 --- a/configs/nanopi-r2c-plus-rk3328_defconfig +++ b/configs/nanopi-r2c-plus-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c-plus" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2c-rk3328_defconfig b/configs/nanopi-r2c-rk3328_defconfig index a4cb148246e6..5a722c182631 100644 --- a/configs/nanopi-r2c-rk3328_defconfig +++ b/configs/nanopi-r2c-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2s-rk3328_defconfig b/configs/nanopi-r2s-rk3328_defconfig index c5d13788528b..985d02475ece 100644 --- a/configs/nanopi-r2s-rk3328_defconfig +++ b/configs/nanopi-r2s-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2s" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/orangepi-r1-plus-lts-rk3328_defconfig b/configs/orangepi-r1-plus-lts-rk3328_defconfig index 6360f5df3864..e9f7a1306923 100644 --- a/configs/orangepi-r1-plus-lts-rk3328_defconfig +++ b/configs/orangepi-r1-plus-lts-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus-lts" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus-lts.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/orangepi-r1-plus-rk3328_defconfig b/configs/orangepi-r1-plus-rk3328_defconfig index 9473a08fe20d..6019f33ae3f5 100644 --- a/configs/orangepi-r1-plus-rk3328_defconfig +++ b/configs/orangepi-r1-plus-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/roc-cc-rk3328_defconfig b/configs/roc-cc-rk3328_defconfig index c66b1ccba267..191dbff928bb 100644 --- a/configs/roc-cc-rk3328_defconfig +++ b/configs/roc-cc-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-roc-cc" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-roc-cc.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock-pi-e-rk3328_defconfig b/configs/rock-pi-e-rk3328_defconfig index 275ffc3ed8f4..e4f2123e0b17 100644 --- a/configs/rock-pi-e-rk3328_defconfig +++ b/configs/rock-pi-e-rk3328_defconfig @@ -2,23 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock-pi-e" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x4000000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 -CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -34,17 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock-pi-e.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock64-rk3328_defconfig b/configs/rock64-rk3328_defconfig index 1cb4e6777d45..f38431891bf8 100644 --- a/configs/rock64-rk3328_defconfig +++ b/configs/rock64-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock64" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock64.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y
Hi Jonas,
This patch does not able to apply on next, could you help to take a look.
And also add document of memory layout in rockchip.rst if possible.
Thanks,
- Kever
On 2024/3/3 03:16, Jonas Karlman wrote:
With the stack and text base used by U-Boot SPL and proper on RK3328 there is a high likelihood of overlapping when U-Boot proper + FDT nears or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3328: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -8K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 32M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [2M, 4M-8K) with this layout. However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se
arch/arm/mach-rockchip/rk3328/Kconfig | 11 ++++------- configs/evb-rk3328_defconfig | 17 ----------------- configs/nanopi-r2c-plus-rk3328_defconfig | 15 --------------- configs/nanopi-r2c-rk3328_defconfig | 15 --------------- configs/nanopi-r2s-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-lts-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-rk3328_defconfig | 15 --------------- configs/roc-cc-rk3328_defconfig | 15 --------------- configs/rock-pi-e-rk3328_defconfig | 17 ----------------- configs/rock64-rk3328_defconfig | 15 --------------- 10 files changed, 4 insertions(+), 146 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3328/Kconfig b/arch/arm/mach-rockchip/rk3328/Kconfig index d5cb649ae6ba..70770da5fdf2 100644 --- a/arch/arm/mach-rockchip/rk3328/Kconfig +++ b/arch/arm/mach-rockchip/rk3328/Kconfig @@ -21,13 +21,7 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3328"
-config SYS_MALLOC_F_LEN
- default 0x2000
-config SPL_LIBCOMMON_SUPPORT
- default y
-config SPL_LIBGENERIC_SUPPORT +config ROCKCHIP_COMMON_STACK_ADDR default y
config TPL_LDSCRIPT @@ -39,6 +33,9 @@ config TPL_TEXT_BASE config TPL_STACK default 0xff098000
+config TPL_SYS_MALLOC_F_LEN
default 0x800
source "board/rockchip/evb_rk3328/Kconfig"
endif
diff --git a/configs/evb-rk3328_defconfig b/configs/evb-rk3328_defconfig index da422c8ba4e7..4fa8a7d365a4 100644 --- a/configs/evb-rk3328_defconfig +++ b/configs/evb-rk3328_defconfig @@ -2,22 +2,12 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-evb" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x4000000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 -CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +23,9 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2c-plus-rk3328_defconfig b/configs/nanopi-r2c-plus-rk3328_defconfig index 25850328f8b8..5302fd91a0f5 100644 --- a/configs/nanopi-r2c-plus-rk3328_defconfig +++ b/configs/nanopi-r2c-plus-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c-plus" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2c-rk3328_defconfig b/configs/nanopi-r2c-rk3328_defconfig index a4cb148246e6..5a722c182631 100644 --- a/configs/nanopi-r2c-rk3328_defconfig +++ b/configs/nanopi-r2c-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2c" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2c.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r2s-rk3328_defconfig b/configs/nanopi-r2s-rk3328_defconfig index c5d13788528b..985d02475ece 100644 --- a/configs/nanopi-r2s-rk3328_defconfig +++ b/configs/nanopi-r2s-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2s" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/orangepi-r1-plus-lts-rk3328_defconfig b/configs/orangepi-r1-plus-lts-rk3328_defconfig index 6360f5df3864..e9f7a1306923 100644 --- a/configs/orangepi-r1-plus-lts-rk3328_defconfig +++ b/configs/orangepi-r1-plus-lts-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus-lts" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus-lts.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/orangepi-r1-plus-rk3328_defconfig b/configs/orangepi-r1-plus-rk3328_defconfig index 9473a08fe20d..6019f33ae3f5 100644 --- a/configs/orangepi-r1-plus-rk3328_defconfig +++ b/configs/orangepi-r1-plus-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/roc-cc-rk3328_defconfig b/configs/roc-cc-rk3328_defconfig index c66b1ccba267..191dbff928bb 100644 --- a/configs/roc-cc-rk3328_defconfig +++ b/configs/roc-cc-rk3328_defconfig @@ -2,22 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-roc-cc" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -33,16 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-roc-cc.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock-pi-e-rk3328_defconfig b/configs/rock-pi-e-rk3328_defconfig index 275ffc3ed8f4..e4f2123e0b17 100644 --- a/configs/rock-pi-e-rk3328_defconfig +++ b/configs/rock-pi-e-rk3328_defconfig @@ -2,23 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock-pi-e" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x4000000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 -CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -34,17 +24,10 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock-pi-e.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_POWER=y CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock64-rk3328_defconfig b/configs/rock64-rk3328_defconfig index 1cb4e6777d45..f38431891bf8 100644 --- a/configs/rock64-rk3328_defconfig +++ b/configs/rock64-rk3328_defconfig @@ -2,23 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3328-rock64" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3328=y -CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y -CONFIG_TPL_LIBCOMMON_SUPPORT=y -CONFIG_TPL_LIBGENERIC_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 -CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,18 +27,12 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock64.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x2000000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y -CONFIG_TPL_SYS_MALLOC_SIMPLE=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y
Hi Kever,
On 2024-03-13 11:39, Kever Yang wrote:
Hi Jonas,
This patch does not able to apply on next, could you help to take a look.
And also add document of memory layout in rockchip.rst if possible.
I will send a follow-up patch that adds details about this memory layout and the new Kconfig option to the rockchip documentation.
Regards, Jonas
Thanks,
- Kever
On 2024/3/3 03:16, Jonas Karlman wrote:
With the stack and text base used by U-Boot SPL and proper on RK3328 there is a high likelihood of overlapping when U-Boot proper + FDT nears or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3328: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -8K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 32M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [2M, 4M-8K) with this layout. However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se
arch/arm/mach-rockchip/rk3328/Kconfig | 11 ++++------- configs/evb-rk3328_defconfig | 17 ----------------- configs/nanopi-r2c-plus-rk3328_defconfig | 15 --------------- configs/nanopi-r2c-rk3328_defconfig | 15 --------------- configs/nanopi-r2s-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-lts-rk3328_defconfig | 15 --------------- configs/orangepi-r1-plus-rk3328_defconfig | 15 --------------- configs/roc-cc-rk3328_defconfig | 15 --------------- configs/rock-pi-e-rk3328_defconfig | 17 ----------------- configs/rock64-rk3328_defconfig | 15 --------------- 10 files changed, 4 insertions(+), 146 deletions(-)
[snip]
With the stack and text base used by U-Boot SPL and proper on RK3399 there is a high likelihood of overlapping when U-Boot proper + FDT nears or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3399: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -16K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -16K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ 4M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE) [ -X, 64M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 63M, 64M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
SPL can safely load U-Boot proper + FDT to [2M, 4M-16K) with this layout. However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- arch/arm/mach-rockchip/rk3399/Kconfig | 7 +++++-- configs/eaidk-610-rk3399_defconfig | 10 ---------- configs/evb-rk3399_defconfig | 10 ---------- configs/firefly-rk3399_defconfig | 10 ---------- configs/khadas-edge-captain-rk3399_defconfig | 10 ---------- configs/khadas-edge-rk3399_defconfig | 10 ---------- configs/khadas-edge-v-rk3399_defconfig | 10 ---------- configs/leez-rk3399_defconfig | 10 ---------- configs/nanopc-t4-rk3399_defconfig | 10 ---------- configs/nanopi-m4-2gb-rk3399_defconfig | 10 ---------- configs/nanopi-m4-rk3399_defconfig | 10 ---------- configs/nanopi-m4b-rk3399_defconfig | 10 ---------- configs/nanopi-neo4-rk3399_defconfig | 10 ---------- configs/nanopi-r4s-rk3399_defconfig | 10 ---------- configs/orangepi-rk3399_defconfig | 10 ---------- configs/pinebook-pro-rk3399_defconfig | 10 ---------- configs/pinephone-pro-rk3399_defconfig | 10 ---------- configs/roc-pc-mezzanine-rk3399_defconfig | 10 ---------- configs/roc-pc-rk3399_defconfig | 10 ---------- configs/rock-4c-plus-rk3399_defconfig | 10 ---------- configs/rock-4se-rk3399_defconfig | 10 ---------- configs/rock-pi-4-rk3399_defconfig | 10 ---------- configs/rock-pi-4c-rk3399_defconfig | 10 ---------- configs/rock-pi-n10-rk3399pro_defconfig | 10 ---------- configs/rock960-rk3399_defconfig | 10 ---------- configs/rockpro64-rk3399_defconfig | 10 ---------- 26 files changed, 5 insertions(+), 252 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3399/Kconfig b/arch/arm/mach-rockchip/rk3399/Kconfig index d01063ac98b6..38904291dfa6 100644 --- a/arch/arm/mach-rockchip/rk3399/Kconfig +++ b/arch/arm/mach-rockchip/rk3399/Kconfig @@ -138,8 +138,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3399"
+config ROCKCHIP_COMMON_STACK_ADDR + default y + config SYS_MALLOC_F_LEN - default 0x4000 + default 0x4000 if !SPL_SHARES_INIT_SP_ADDR
config SPL_LIBCOMMON_SUPPORT default y @@ -157,7 +160,7 @@ config TPL_TEXT_BASE default 0xff8c2000
config SPL_STACK_R_ADDR - default 0x04000000 + default 0x04000000 if !SPL_SHARES_INIT_SP_ADDR
if BOOTCOUNT_LIMIT
diff --git a/configs/eaidk-610-rk3399_defconfig b/configs/eaidk-610-rk3399_defconfig index 0ca4cebc4d90..4d8b495ccfec 100644 --- a/configs/eaidk-610-rk3399_defconfig +++ b/configs/eaidk-610-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-eaidk-610" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-eaidk-610.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/evb-rk3399_defconfig b/configs/evb-rk3399_defconfig index 1d1e55162290..d81c7f9604e1 100644 --- a/configs/evb-rk3399_defconfig +++ b/configs/evb-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-evb" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -21,13 +17,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/firefly-rk3399_defconfig b/configs/firefly-rk3399_defconfig index 2fe38f81c50d..545c047c6df8 100644 --- a/configs/firefly-rk3399_defconfig +++ b/configs/firefly-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-firefly" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -22,13 +18,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-firefly.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/khadas-edge-captain-rk3399_defconfig b/configs/khadas-edge-captain-rk3399_defconfig index 28a59899e1cb..310250ed4a52 100644 --- a/configs/khadas-edge-captain-rk3399_defconfig +++ b/configs/khadas-edge-captain-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-khadas-edge-captain" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -20,13 +16,7 @@ CONFIG_SYS_PBSIZE=1048 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="kedge# " diff --git a/configs/khadas-edge-rk3399_defconfig b/configs/khadas-edge-rk3399_defconfig index 075e28a509f4..3fe5542d1256 100644 --- a/configs/khadas-edge-rk3399_defconfig +++ b/configs/khadas-edge-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-khadas-edge" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -20,13 +16,7 @@ CONFIG_SYS_PBSIZE=1048 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="kedge# " diff --git a/configs/khadas-edge-v-rk3399_defconfig b/configs/khadas-edge-v-rk3399_defconfig index c65690ce3da7..4b41454d710d 100644 --- a/configs/khadas-edge-v-rk3399_defconfig +++ b/configs/khadas-edge-v-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-khadas-edge-v" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -20,13 +16,7 @@ CONFIG_SYS_PBSIZE=1048 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="kedge# " diff --git a/configs/leez-rk3399_defconfig b/configs/leez-rk3399_defconfig index 2122018e7a3e..e5088341389a 100644 --- a/configs/leez-rk3399_defconfig +++ b/configs/leez-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-leez-p710" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,12 +15,6 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-leez-p710.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig index c1617d740112..cdfacb66e678 100644 --- a/configs/nanopc-t4-rk3399_defconfig +++ b/configs/nanopc-t4-rk3399_defconfig @@ -2,16 +2,12 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -21,13 +17,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-m4-2gb-rk3399_defconfig b/configs/nanopi-m4-2gb-rk3399_defconfig index 4d70fde6b14d..51596f57ae35 100644 --- a/configs/nanopi-m4-2gb-rk3399_defconfig +++ b/configs/nanopi-m4-2gb-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4-2gb" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4-2gb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig index a96fe0306dad..2af84fb6ff17 100644 --- a/configs/nanopi-m4-rk3399_defconfig +++ b/configs/nanopi-m4-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-m4b-rk3399_defconfig b/configs/nanopi-m4b-rk3399_defconfig index c8faccb233a5..1b76f98e0df7 100644 --- a/configs/nanopi-m4b-rk3399_defconfig +++ b/configs/nanopi-m4b-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4b" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4b.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-neo4-rk3399_defconfig b/configs/nanopi-neo4-rk3399_defconfig index 1c4ffbb44041..c176c5a12111 100644 --- a/configs/nanopi-neo4-rk3399_defconfig +++ b/configs/nanopi-neo4-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-neo4" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-neo4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-r4s-rk3399_defconfig b/configs/nanopi-r4s-rk3399_defconfig index 50dbd7a854d4..ea01d323541b 100644 --- a/configs/nanopi-r4s-rk3399_defconfig +++ b/configs/nanopi-r4s-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-r4s" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-r4s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig index bc2c4782efbc..c6a92b2decf3 100644 --- a/configs/orangepi-rk3399_defconfig +++ b/configs/orangepi-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/pinebook-pro-rk3399_defconfig b/configs/pinebook-pro-rk3399_defconfig index 3083d0a8bb77..57e614c314e9 100644 --- a/configs/pinebook-pro-rk3399_defconfig +++ b/configs/pinebook-pro-rk3399_defconfig @@ -2,10 +2,7 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 @@ -14,7 +11,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_PINEBOOK_PRO_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -28,13 +24,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-pinebook-pro.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y diff --git a/configs/pinephone-pro-rk3399_defconfig b/configs/pinephone-pro-rk3399_defconfig index 454cb7eec76b..49d3d0456b57 100644 --- a/configs/pinephone-pro-rk3399_defconfig +++ b/configs/pinephone-pro-rk3399_defconfig @@ -2,10 +2,7 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 @@ -14,7 +11,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_PINEPHONE_PRO_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -27,13 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-pinephone-pro.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y diff --git a/configs/roc-pc-mezzanine-rk3399_defconfig b/configs/roc-pc-mezzanine-rk3399_defconfig index 8d4153ea5f0e..1ff4e15c8c10 100644 --- a/configs/roc-pc-mezzanine-rk3399_defconfig +++ b/configs/roc-pc-mezzanine-rk3399_defconfig @@ -2,11 +2,8 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_ENV_SECT_SIZE=0x1000 @@ -15,7 +12,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_ROC_PC_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -28,13 +24,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-roc-pc-mezzanine.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x20000 CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 diff --git a/configs/roc-pc-rk3399_defconfig b/configs/roc-pc-rk3399_defconfig index 3824eb22d3da..a41f71d9e167 100644 --- a/configs/roc-pc-rk3399_defconfig +++ b/configs/roc-pc-rk3399_defconfig @@ -2,11 +2,8 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=30000000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 @@ -16,7 +13,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_ROC_PC_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -29,13 +25,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-roc-pc.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x20000 CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 diff --git a/configs/rock-4c-plus-rk3399_defconfig b/configs/rock-4c-plus-rk3399_defconfig index 67ad54610a72..1652da5b6ca6 100644 --- a/configs/rock-4c-plus-rk3399_defconfig +++ b/configs/rock-4c-plus-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-4c-plus" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -23,13 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-4c-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock-4se-rk3399_defconfig b/configs/rock-4se-rk3399_defconfig index b0993bb81020..e51a074a2972 100644 --- a/configs/rock-4se-rk3399_defconfig +++ b/configs/rock-4se-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-4se" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -25,13 +21,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-4se.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_TPL=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_NVEDIT_EFI=y diff --git a/configs/rock-pi-4-rk3399_defconfig b/configs/rock-pi-4-rk3399_defconfig index 2df3cd41e16c..6dc607590050 100644 --- a/configs/rock-pi-4-rk3399_defconfig +++ b/configs/rock-pi-4-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-pi-4a" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -25,13 +21,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-pi-4a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock-pi-4c-rk3399_defconfig b/configs/rock-pi-4c-rk3399_defconfig index bac745202bc7..5c71f0bd9e8e 100644 --- a/configs/rock-pi-4c-rk3399_defconfig +++ b/configs/rock-pi-4c-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-pi-4c" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -23,13 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-pi-4c.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock-pi-n10-rk3399pro_defconfig b/configs/rock-pi-n10-rk3399pro_defconfig index e86df4b7456a..6889cdcbf7d8 100644 --- a/configs/rock-pi-n10-rk3399pro_defconfig +++ b/configs/rock-pi-n10-rk3399pro_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399pro-rock-pi-n10" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -24,13 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399pro-rock-pi-n10.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock960-rk3399_defconfig b/configs/rock960-rk3399_defconfig index a9cae27ccd2f..5c0b95f10bd1 100644 --- a/configs/rock960-rk3399_defconfig +++ b/configs/rock960-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock960" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_ROCK960_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -22,13 +18,7 @@ CONFIG_SYS_PBSIZE=1052 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="rock960 => " diff --git a/configs/rockpro64-rk3399_defconfig b/configs/rockpro64-rk3399_defconfig index b9c885cfee55..4de3d5b1c7f8 100644 --- a/configs/rockpro64-rk3399_defconfig +++ b/configs/rockpro64-rk3399_defconfig @@ -2,10 +2,7 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rockpro64" @@ -13,7 +10,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_ROCKPRO64_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -30,13 +26,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rockpro64.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
On 2024/3/3 03:16, Jonas Karlman wrote:
With the stack and text base used by U-Boot SPL and proper on RK3399 there is a high likelihood of overlapping when U-Boot proper + FDT nears or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3399: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -16K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -16K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ 4M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE) [ -X, 64M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 63M, 64M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
SPL can safely load U-Boot proper + FDT to [2M, 4M-16K) with this layout. However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
arch/arm/mach-rockchip/rk3399/Kconfig | 7 +++++-- configs/eaidk-610-rk3399_defconfig | 10 ---------- configs/evb-rk3399_defconfig | 10 ---------- configs/firefly-rk3399_defconfig | 10 ---------- configs/khadas-edge-captain-rk3399_defconfig | 10 ---------- configs/khadas-edge-rk3399_defconfig | 10 ---------- configs/khadas-edge-v-rk3399_defconfig | 10 ---------- configs/leez-rk3399_defconfig | 10 ---------- configs/nanopc-t4-rk3399_defconfig | 10 ---------- configs/nanopi-m4-2gb-rk3399_defconfig | 10 ---------- configs/nanopi-m4-rk3399_defconfig | 10 ---------- configs/nanopi-m4b-rk3399_defconfig | 10 ---------- configs/nanopi-neo4-rk3399_defconfig | 10 ---------- configs/nanopi-r4s-rk3399_defconfig | 10 ---------- configs/orangepi-rk3399_defconfig | 10 ---------- configs/pinebook-pro-rk3399_defconfig | 10 ---------- configs/pinephone-pro-rk3399_defconfig | 10 ---------- configs/roc-pc-mezzanine-rk3399_defconfig | 10 ---------- configs/roc-pc-rk3399_defconfig | 10 ---------- configs/rock-4c-plus-rk3399_defconfig | 10 ---------- configs/rock-4se-rk3399_defconfig | 10 ---------- configs/rock-pi-4-rk3399_defconfig | 10 ---------- configs/rock-pi-4c-rk3399_defconfig | 10 ---------- configs/rock-pi-n10-rk3399pro_defconfig | 10 ---------- configs/rock960-rk3399_defconfig | 10 ---------- configs/rockpro64-rk3399_defconfig | 10 ---------- 26 files changed, 5 insertions(+), 252 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3399/Kconfig b/arch/arm/mach-rockchip/rk3399/Kconfig index d01063ac98b6..38904291dfa6 100644 --- a/arch/arm/mach-rockchip/rk3399/Kconfig +++ b/arch/arm/mach-rockchip/rk3399/Kconfig @@ -138,8 +138,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3399"
+config ROCKCHIP_COMMON_STACK_ADDR
- default y
- config SYS_MALLOC_F_LEN
- default 0x4000
default 0x4000 if !SPL_SHARES_INIT_SP_ADDR
config SPL_LIBCOMMON_SUPPORT default y
@@ -157,7 +160,7 @@ config TPL_TEXT_BASE default 0xff8c2000
config SPL_STACK_R_ADDR
- default 0x04000000
default 0x04000000 if !SPL_SHARES_INIT_SP_ADDR
if BOOTCOUNT_LIMIT
diff --git a/configs/eaidk-610-rk3399_defconfig b/configs/eaidk-610-rk3399_defconfig index 0ca4cebc4d90..4d8b495ccfec 100644 --- a/configs/eaidk-610-rk3399_defconfig +++ b/configs/eaidk-610-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-eaidk-610" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-eaidk-610.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/evb-rk3399_defconfig b/configs/evb-rk3399_defconfig index 1d1e55162290..d81c7f9604e1 100644 --- a/configs/evb-rk3399_defconfig +++ b/configs/evb-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-evb" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -21,13 +17,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/firefly-rk3399_defconfig b/configs/firefly-rk3399_defconfig index 2fe38f81c50d..545c047c6df8 100644 --- a/configs/firefly-rk3399_defconfig +++ b/configs/firefly-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-firefly" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -22,13 +18,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-firefly.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/khadas-edge-captain-rk3399_defconfig b/configs/khadas-edge-captain-rk3399_defconfig index 28a59899e1cb..310250ed4a52 100644 --- a/configs/khadas-edge-captain-rk3399_defconfig +++ b/configs/khadas-edge-captain-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-khadas-edge-captain" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -20,13 +16,7 @@ CONFIG_SYS_PBSIZE=1048 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="kedge# " diff --git a/configs/khadas-edge-rk3399_defconfig b/configs/khadas-edge-rk3399_defconfig index 075e28a509f4..3fe5542d1256 100644 --- a/configs/khadas-edge-rk3399_defconfig +++ b/configs/khadas-edge-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-khadas-edge" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -20,13 +16,7 @@ CONFIG_SYS_PBSIZE=1048 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="kedge# " diff --git a/configs/khadas-edge-v-rk3399_defconfig b/configs/khadas-edge-v-rk3399_defconfig index c65690ce3da7..4b41454d710d 100644 --- a/configs/khadas-edge-v-rk3399_defconfig +++ b/configs/khadas-edge-v-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-khadas-edge-v" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -20,13 +16,7 @@ CONFIG_SYS_PBSIZE=1048 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="kedge# " diff --git a/configs/leez-rk3399_defconfig b/configs/leez-rk3399_defconfig index 2122018e7a3e..e5088341389a 100644 --- a/configs/leez-rk3399_defconfig +++ b/configs/leez-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-leez-p710" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,12 +15,6 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-leez-p710.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopc-t4-rk3399_defconfig b/configs/nanopc-t4-rk3399_defconfig index c1617d740112..cdfacb66e678 100644 --- a/configs/nanopc-t4-rk3399_defconfig +++ b/configs/nanopc-t4-rk3399_defconfig @@ -2,16 +2,12 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -21,13 +17,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-m4-2gb-rk3399_defconfig b/configs/nanopi-m4-2gb-rk3399_defconfig index 4d70fde6b14d..51596f57ae35 100644 --- a/configs/nanopi-m4-2gb-rk3399_defconfig +++ b/configs/nanopi-m4-2gb-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4-2gb" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4-2gb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-m4-rk3399_defconfig b/configs/nanopi-m4-rk3399_defconfig index a96fe0306dad..2af84fb6ff17 100644 --- a/configs/nanopi-m4-rk3399_defconfig +++ b/configs/nanopi-m4-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-m4b-rk3399_defconfig b/configs/nanopi-m4b-rk3399_defconfig index c8faccb233a5..1b76f98e0df7 100644 --- a/configs/nanopi-m4b-rk3399_defconfig +++ b/configs/nanopi-m4b-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4b" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4b.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-neo4-rk3399_defconfig b/configs/nanopi-neo4-rk3399_defconfig index 1c4ffbb44041..c176c5a12111 100644 --- a/configs/nanopi-neo4-rk3399_defconfig +++ b/configs/nanopi-neo4-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-neo4" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-neo4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/nanopi-r4s-rk3399_defconfig b/configs/nanopi-r4s-rk3399_defconfig index 50dbd7a854d4..ea01d323541b 100644 --- a/configs/nanopi-r4s-rk3399_defconfig +++ b/configs/nanopi-r4s-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-r4s" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-r4s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/orangepi-rk3399_defconfig b/configs/orangepi-rk3399_defconfig index bc2c4782efbc..c6a92b2decf3 100644 --- a/configs/orangepi-rk3399_defconfig +++ b/configs/orangepi-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi" CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -19,13 +15,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/pinebook-pro-rk3399_defconfig b/configs/pinebook-pro-rk3399_defconfig index 3083d0a8bb77..57e614c314e9 100644 --- a/configs/pinebook-pro-rk3399_defconfig +++ b/configs/pinebook-pro-rk3399_defconfig @@ -2,10 +2,7 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 @@ -14,7 +11,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_PINEBOOK_PRO_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -28,13 +24,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-pinebook-pro.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y diff --git a/configs/pinephone-pro-rk3399_defconfig b/configs/pinephone-pro-rk3399_defconfig index 454cb7eec76b..49d3d0456b57 100644 --- a/configs/pinephone-pro-rk3399_defconfig +++ b/configs/pinephone-pro-rk3399_defconfig @@ -2,10 +2,7 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 @@ -14,7 +11,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_PINEPHONE_PRO_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -27,13 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-pinephone-pro.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y diff --git a/configs/roc-pc-mezzanine-rk3399_defconfig b/configs/roc-pc-mezzanine-rk3399_defconfig index 8d4153ea5f0e..1ff4e15c8c10 100644 --- a/configs/roc-pc-mezzanine-rk3399_defconfig +++ b/configs/roc-pc-mezzanine-rk3399_defconfig @@ -2,11 +2,8 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_ENV_SECT_SIZE=0x1000 @@ -15,7 +12,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_ROC_PC_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -28,13 +24,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-roc-pc-mezzanine.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x20000 CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 diff --git a/configs/roc-pc-rk3399_defconfig b/configs/roc-pc-rk3399_defconfig index 3824eb22d3da..a41f71d9e167 100644 --- a/configs/roc-pc-rk3399_defconfig +++ b/configs/roc-pc-rk3399_defconfig @@ -2,11 +2,8 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_SF_DEFAULT_SPEED=30000000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 @@ -16,7 +13,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_ROC_PC_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -29,13 +25,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-roc-pc.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x20000 CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 diff --git a/configs/rock-4c-plus-rk3399_defconfig b/configs/rock-4c-plus-rk3399_defconfig index 67ad54610a72..1652da5b6ca6 100644 --- a/configs/rock-4c-plus-rk3399_defconfig +++ b/configs/rock-4c-plus-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-4c-plus" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -23,13 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-4c-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock-4se-rk3399_defconfig b/configs/rock-4se-rk3399_defconfig index b0993bb81020..e51a074a2972 100644 --- a/configs/rock-4se-rk3399_defconfig +++ b/configs/rock-4se-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-4se" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -25,13 +21,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-4se.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_TPL=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_NVEDIT_EFI=y diff --git a/configs/rock-pi-4-rk3399_defconfig b/configs/rock-pi-4-rk3399_defconfig index 2df3cd41e16c..6dc607590050 100644 --- a/configs/rock-pi-4-rk3399_defconfig +++ b/configs/rock-pi-4-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-pi-4a" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -25,13 +21,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-pi-4a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock-pi-4c-rk3399_defconfig b/configs/rock-pi-4c-rk3399_defconfig index bac745202bc7..5c71f0bd9e8e 100644 --- a/configs/rock-pi-4c-rk3399_defconfig +++ b/configs/rock-pi-4c-rk3399_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-pi-4c" CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -23,13 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-pi-4c.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock-pi-n10-rk3399pro_defconfig b/configs/rock-pi-n10-rk3399pro_defconfig index e86df4b7456a..6889cdcbf7d8 100644 --- a/configs/rock-pi-n10-rk3399pro_defconfig +++ b/configs/rock-pi-n10-rk3399pro_defconfig @@ -2,17 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_SPL_GPIO=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399pro-rock-pi-n10" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_EVB_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -24,13 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399pro-rock-pi-n10.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_CMD_BOOTZ=y diff --git a/configs/rock960-rk3399_defconfig b/configs/rock960-rk3399_defconfig index a9cae27ccd2f..5c0b95f10bd1 100644 --- a/configs/rock960-rk3399_defconfig +++ b/configs/rock960-rk3399_defconfig @@ -2,15 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock960" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_TARGET_ROCK960_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 @@ -22,13 +18,7 @@ CONFIG_SYS_PBSIZE=1052 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y CONFIG_TPL=y CONFIG_SYS_PROMPT="rock960 => " diff --git a/configs/rockpro64-rk3399_defconfig b/configs/rockpro64-rk3399_defconfig index b9c885cfee55..4de3d5b1c7f8 100644 --- a/configs/rockpro64-rk3399_defconfig +++ b/configs/rockpro64-rk3399_defconfig @@ -2,10 +2,7 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00200000 CONFIG_NR_DRAM_BANKS=1 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ENV_SIZE=0x8000 CONFIG_ENV_OFFSET=0x3F8000 CONFIG_DEFAULT_DEVICE_TREE="rk3399-rockpro64" @@ -13,7 +10,6 @@ CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3399=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_TARGET_ROCKPRO64_RK3399=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -30,13 +26,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rockpro64.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x400000 -CONFIG_SPL_BSS_MAX_SIZE=0x2000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y -CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000 CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000 CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
Currently the following memory layout is typically used on RK356x: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [-128K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 10M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [-128K, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 12M-128K) with this layout.
Migrate to use common bss, stack and malloc heap size and addresses to remove this size limitation.
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- arch/arm/mach-rockchip/rk3568/Kconfig | 7 +++++-- configs/anbernic-rgxx3-rk3566_defconfig | 13 ------------- configs/bpi-r2-pro-rk3568_defconfig | 13 ------------- configs/evb-rk3568_defconfig | 13 ------------- configs/generic-rk3568_defconfig | 13 ------------- configs/lubancat-2-rk3568_defconfig | 13 ------------- configs/nanopi-r5c-rk3568_defconfig | 13 ------------- configs/nanopi-r5s-rk3568_defconfig | 13 ------------- configs/odroid-m1-rk3568_defconfig | 13 ------------- configs/quartz64-a-rk3566_defconfig | 13 ------------- configs/quartz64-b-rk3566_defconfig | 13 ------------- configs/radxa-cm3-io-rk3566_defconfig | 13 ------------- configs/radxa-e25-rk3568_defconfig | 13 ------------- configs/rock-3a-rk3568_defconfig | 13 ------------- configs/soquartz-blade-rk3566_defconfig | 13 ------------- configs/soquartz-cm4-rk3566_defconfig | 13 ------------- configs/soquartz-model-a-rk3566_defconfig | 13 ------------- 17 files changed, 5 insertions(+), 210 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3568/Kconfig b/arch/arm/mach-rockchip/rk3568/Kconfig index baa51349f4be..af537d912a62 100644 --- a/arch/arm/mach-rockchip/rk3568/Kconfig +++ b/arch/arm/mach-rockchip/rk3568/Kconfig @@ -38,8 +38,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3568"
-config SYS_MALLOC_F_LEN - default 0x20000 +config ROCKCHIP_COMMON_STACK_ADDR + default y + +config TEXT_BASE + default 0x00a00000
source "board/rockchip/evb_rk3568/Kconfig" source "board/anbernic/rgxx3_rk3566/Kconfig" diff --git a/configs/anbernic-rgxx3-rk3566_defconfig b/configs/anbernic-rgxx3-rk3566_defconfig index ed6643d9d4fa..2b484fcaef5e 100644 --- a/configs/anbernic-rgxx3-rk3566_defconfig +++ b/configs/anbernic-rgxx3-rk3566_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-anbernic-rgxx3" CONFIG_ROCKCHIP_RK3568=y CONFIG_SPL_ROCKCHIP_BACK_TO_BROM=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y CONFIG_SPL_MMC=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_ANBERNIC_RGXX3_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -34,13 +26,8 @@ CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_BOARD_RNG_SEED=y CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 CONFIG_SPL_BOARD_INIT=y # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_PWM=y CONFIG_CMD_GPT=y diff --git a/configs/bpi-r2-pro-rk3568_defconfig b/configs/bpi-r2-pro-rk3568_defconfig index e6e0e6fc6fa6..5cc95241ba43 100644 --- a/configs/bpi-r2-pro-rk3568_defconfig +++ b/configs/bpi-r2-pro-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-bpi-r2-pro" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-bpi-r2-pro.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_SYS_PROMPT="BPI-R2PRO> " CONFIG_CMD_GPIO=y diff --git a/configs/evb-rk3568_defconfig b/configs/evb-rk3568_defconfig index cb9b87ff12cb..6e8061f5f487 100644 --- a/configs/evb-rk3568_defconfig +++ b/configs/evb-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-evb" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/generic-rk3568_defconfig b/configs/generic-rk3568_defconfig index 8fb79c9b4403..e7d5e55bbfd8 100644 --- a/configs/generic-rk3568_defconfig +++ b/configs/generic-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-generic" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-generic.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/lubancat-2-rk3568_defconfig b/configs/lubancat-2-rk3568_defconfig index 80ae6ec3a2e9..1c50a0ccbe60 100644 --- a/configs/lubancat-2-rk3568_defconfig +++ b/configs/lubancat-2-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-lubancat-2" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-lubancat-2.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r5c-rk3568_defconfig b/configs/nanopi-r5c-rk3568_defconfig index f5a472d03d78..0f1a9461a0ce 100644 --- a/configs/nanopi-r5c-rk3568_defconfig +++ b/configs/nanopi-r5c-rk3568_defconfig @@ -3,18 +3,10 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-nanopi-r5c" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-nanopi-r5c.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r5s-rk3568_defconfig b/configs/nanopi-r5s-rk3568_defconfig index 99692d341f44..4ebf0cc9ee88 100644 --- a/configs/nanopi-r5s-rk3568_defconfig +++ b/configs/nanopi-r5s-rk3568_defconfig @@ -3,18 +3,10 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-nanopi-r5s" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-nanopi-r5s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/odroid-m1-rk3568_defconfig b/configs/odroid-m1-rk3568_defconfig index 3130e341e776..b5ed9e4bc98e 100644 --- a/configs/odroid-m1-rk3568_defconfig +++ b/configs/odroid-m1-rk3568_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x1000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-odroid-m1" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_ODROID_M1_RK3568=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,12 +28,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-odroid-m1.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x100000 CONFIG_SPL_ATF=y diff --git a/configs/quartz64-a-rk3566_defconfig b/configs/quartz64-a-rk3566_defconfig index ade08867f60f..fef80439d89b 100644 --- a/configs/quartz64-a-rk3566_defconfig +++ b/configs/quartz64-a-rk3566_defconfig @@ -2,23 +2,15 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 CONFIG_SPL_GPIO=y -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-a" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -37,12 +29,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 diff --git a/configs/quartz64-b-rk3566_defconfig b/configs/quartz64-b-rk3566_defconfig index 8d01db54407d..bb541ed1af63 100644 --- a/configs/quartz64-b-rk3566_defconfig +++ b/configs/quartz64-b-rk3566_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-b" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,12 +28,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-b.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/radxa-cm3-io-rk3566_defconfig b/configs/radxa-cm3-io-rk3566_defconfig index 4b606dcb8e94..bf61db44d3a4 100644 --- a/configs/radxa-cm3-io-rk3566_defconfig +++ b/configs/radxa-cm3-io-rk3566_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-radxa-cm3-io" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-radxa-cm3-io.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/radxa-e25-rk3568_defconfig b/configs/radxa-e25-rk3568_defconfig index fedb137877ab..43aa8ec20e48 100644 --- a/configs/radxa-e25-rk3568_defconfig +++ b/configs/radxa-e25-rk3568_defconfig @@ -3,18 +3,10 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-radxa-e25" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-radxa-e25.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock-3a-rk3568_defconfig b/configs/rock-3a-rk3568_defconfig index 18372a570eb7..c161bc974fb0 100644 --- a/configs/rock-3a-rk3568_defconfig +++ b/configs/rock-3a-rk3568_defconfig @@ -2,21 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-rock-3a" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -35,12 +27,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-rock-3a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/soquartz-blade-rk3566_defconfig b/configs/soquartz-blade-rk3566_defconfig index 9693cc2f9eb9..b9ac6b9f33d5 100644 --- a/configs/soquartz-blade-rk3566_defconfig +++ b/configs/soquartz-blade-rk3566_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-blade" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-blade.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/soquartz-cm4-rk3566_defconfig b/configs/soquartz-cm4-rk3566_defconfig index 9c6b12d23028..e87a6392c527 100644 --- a/configs/soquartz-cm4-rk3566_defconfig +++ b/configs/soquartz-cm4-rk3566_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-cm4" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-cm4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/soquartz-model-a-rk3566_defconfig b/configs/soquartz-model-a-rk3566_defconfig index fd72d78a47a8..b2c1684515e8 100644 --- a/configs/soquartz-model-a-rk3566_defconfig +++ b/configs/soquartz-model-a-rk3566_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-model-a" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-model-a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y
On 2024/3/3 03:16, Jonas Karlman wrote:
Currently the following memory layout is typically used on RK356x: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [-128K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 10M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [-128K, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 12M-128K) with this layout.
Migrate to use common bss, stack and malloc heap size and addresses to remove this size limitation.
Signed-off-by: Jonas Karlman jonas@kwiboo.se
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
arch/arm/mach-rockchip/rk3568/Kconfig | 7 +++++-- configs/anbernic-rgxx3-rk3566_defconfig | 13 ------------- configs/bpi-r2-pro-rk3568_defconfig | 13 ------------- configs/evb-rk3568_defconfig | 13 ------------- configs/generic-rk3568_defconfig | 13 ------------- configs/lubancat-2-rk3568_defconfig | 13 ------------- configs/nanopi-r5c-rk3568_defconfig | 13 ------------- configs/nanopi-r5s-rk3568_defconfig | 13 ------------- configs/odroid-m1-rk3568_defconfig | 13 ------------- configs/quartz64-a-rk3566_defconfig | 13 ------------- configs/quartz64-b-rk3566_defconfig | 13 ------------- configs/radxa-cm3-io-rk3566_defconfig | 13 ------------- configs/radxa-e25-rk3568_defconfig | 13 ------------- configs/rock-3a-rk3568_defconfig | 13 ------------- configs/soquartz-blade-rk3566_defconfig | 13 ------------- configs/soquartz-cm4-rk3566_defconfig | 13 ------------- configs/soquartz-model-a-rk3566_defconfig | 13 ------------- 17 files changed, 5 insertions(+), 210 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3568/Kconfig b/arch/arm/mach-rockchip/rk3568/Kconfig index baa51349f4be..af537d912a62 100644 --- a/arch/arm/mach-rockchip/rk3568/Kconfig +++ b/arch/arm/mach-rockchip/rk3568/Kconfig @@ -38,8 +38,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3568"
-config SYS_MALLOC_F_LEN
- default 0x20000
+config ROCKCHIP_COMMON_STACK_ADDR
- default y
+config TEXT_BASE
default 0x00a00000
source "board/rockchip/evb_rk3568/Kconfig" source "board/anbernic/rgxx3_rk3566/Kconfig"
diff --git a/configs/anbernic-rgxx3-rk3566_defconfig b/configs/anbernic-rgxx3-rk3566_defconfig index ed6643d9d4fa..2b484fcaef5e 100644 --- a/configs/anbernic-rgxx3-rk3566_defconfig +++ b/configs/anbernic-rgxx3-rk3566_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-anbernic-rgxx3" CONFIG_ROCKCHIP_RK3568=y CONFIG_SPL_ROCKCHIP_BACK_TO_BROM=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y CONFIG_SPL_MMC=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_ANBERNIC_RGXX3_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -34,13 +26,8 @@ CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_BOARD_RNG_SEED=y CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 CONFIG_SPL_BOARD_INIT=y # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_PWM=y CONFIG_CMD_GPT=y diff --git a/configs/bpi-r2-pro-rk3568_defconfig b/configs/bpi-r2-pro-rk3568_defconfig index e6e0e6fc6fa6..5cc95241ba43 100644 --- a/configs/bpi-r2-pro-rk3568_defconfig +++ b/configs/bpi-r2-pro-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-bpi-r2-pro" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-bpi-r2-pro.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_SYS_PROMPT="BPI-R2PRO> " CONFIG_CMD_GPIO=y diff --git a/configs/evb-rk3568_defconfig b/configs/evb-rk3568_defconfig index cb9b87ff12cb..6e8061f5f487 100644 --- a/configs/evb-rk3568_defconfig +++ b/configs/evb-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-evb" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/generic-rk3568_defconfig b/configs/generic-rk3568_defconfig index 8fb79c9b4403..e7d5e55bbfd8 100644 --- a/configs/generic-rk3568_defconfig +++ b/configs/generic-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-generic" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-generic.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/lubancat-2-rk3568_defconfig b/configs/lubancat-2-rk3568_defconfig index 80ae6ec3a2e9..1c50a0ccbe60 100644 --- a/configs/lubancat-2-rk3568_defconfig +++ b/configs/lubancat-2-rk3568_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-lubancat-2" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-lubancat-2.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r5c-rk3568_defconfig b/configs/nanopi-r5c-rk3568_defconfig index f5a472d03d78..0f1a9461a0ce 100644 --- a/configs/nanopi-r5c-rk3568_defconfig +++ b/configs/nanopi-r5c-rk3568_defconfig @@ -3,18 +3,10 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-nanopi-r5c" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-nanopi-r5c.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopi-r5s-rk3568_defconfig b/configs/nanopi-r5s-rk3568_defconfig index 99692d341f44..4ebf0cc9ee88 100644 --- a/configs/nanopi-r5s-rk3568_defconfig +++ b/configs/nanopi-r5s-rk3568_defconfig @@ -3,18 +3,10 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-nanopi-r5s" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-nanopi-r5s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/odroid-m1-rk3568_defconfig b/configs/odroid-m1-rk3568_defconfig index 3130e341e776..b5ed9e4bc98e 100644 --- a/configs/odroid-m1-rk3568_defconfig +++ b/configs/odroid-m1-rk3568_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x1000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-odroid-m1" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_ODROID_M1_RK3568=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,12 +28,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-odroid-m1.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x100000 CONFIG_SPL_ATF=y diff --git a/configs/quartz64-a-rk3566_defconfig b/configs/quartz64-a-rk3566_defconfig index ade08867f60f..fef80439d89b 100644 --- a/configs/quartz64-a-rk3566_defconfig +++ b/configs/quartz64-a-rk3566_defconfig @@ -2,23 +2,15 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 CONFIG_SPL_GPIO=y -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-a" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -37,12 +29,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_POWER=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 diff --git a/configs/quartz64-b-rk3566_defconfig b/configs/quartz64-b-rk3566_defconfig index 8d01db54407d..bb541ed1af63 100644 --- a/configs/quartz64-b-rk3566_defconfig +++ b/configs/quartz64-b-rk3566_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-b" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -36,12 +28,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-b.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/radxa-cm3-io-rk3566_defconfig b/configs/radxa-cm3-io-rk3566_defconfig index 4b606dcb8e94..bf61db44d3a4 100644 --- a/configs/radxa-cm3-io-rk3566_defconfig +++ b/configs/radxa-cm3-io-rk3566_defconfig @@ -2,18 +2,10 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-radxa-cm3-io" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -28,12 +20,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-radxa-cm3-io.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/radxa-e25-rk3568_defconfig b/configs/radxa-e25-rk3568_defconfig index fedb137877ab..43aa8ec20e48 100644 --- a/configs/radxa-e25-rk3568_defconfig +++ b/configs/radxa-e25-rk3568_defconfig @@ -3,18 +3,10 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-radxa-e25" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-radxa-e25.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock-3a-rk3568_defconfig b/configs/rock-3a-rk3568_defconfig index 18372a570eb7..c161bc974fb0 100644 --- a/configs/rock-3a-rk3568_defconfig +++ b/configs/rock-3a-rk3568_defconfig @@ -2,21 +2,13 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3568-rock-3a" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -35,12 +27,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-rock-3a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/soquartz-blade-rk3566_defconfig b/configs/soquartz-blade-rk3566_defconfig index 9693cc2f9eb9..b9ac6b9f33d5 100644 --- a/configs/soquartz-blade-rk3566_defconfig +++ b/configs/soquartz-blade-rk3566_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-blade" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-blade.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/soquartz-cm4-rk3566_defconfig b/configs/soquartz-cm4-rk3566_defconfig index 9c6b12d23028..e87a6392c527 100644 --- a/configs/soquartz-cm4-rk3566_defconfig +++ b/configs/soquartz-cm4-rk3566_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-cm4" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-cm4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/soquartz-model-a-rk3566_defconfig b/configs/soquartz-model-a-rk3566_defconfig index fd72d78a47a8..b2c1684515e8 100644 --- a/configs/soquartz-model-a-rk3566_defconfig +++ b/configs/soquartz-model-a-rk3566_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-model-a" CONFIG_ROCKCHIP_RK3568=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZ64_RK3566=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -31,12 +23,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-model-a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y
Currently the following memory layout is typically used on RK3588: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ 3.5M, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 10M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [11.5M, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 11.5M) with this layout.
However, on ROCK 5A the SPL stacks is overlapping: [ -X, 16M) - SPL pre-reloc stack (SPL_STACK) [15.5M, 16M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 16M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 15M, 16M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
Because bind and probe udevice instanses is allocated on the pre-reloc malloc heap, there is going to be an overlap when reloc malloc heap reaches close to 512 KiB of usage.
Migrate to use common bss, stack and malloc heap size and addresses to mitigate these limitations and allow for a larger U-Boot proper size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se --- arch/arm/mach-rockchip/rk3588/Kconfig | 7 +++++-- configs/evb-rk3588_defconfig | 13 ------------- configs/nanopc-t6-rk3588_defconfig | 13 ------------- configs/neu6a-io-rk3588_defconfig | 13 ------------- configs/neu6b-io-rk3588_defconfig | 13 ------------- configs/orangepi-5-plus-rk3588_defconfig | 13 ------------- configs/orangepi-5-rk3588s_defconfig | 13 ------------- configs/quartzpro64-rk3588_defconfig | 13 ------------- configs/rock5a-rk3588s_defconfig | 13 ------------- configs/rock5b-rk3588_defconfig | 13 ------------- configs/turing-rk1-rk3588_defconfig | 13 ------------- 11 files changed, 5 insertions(+), 132 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3588/Kconfig b/arch/arm/mach-rockchip/rk3588/Kconfig index a2193fbd41fe..1ce65566261b 100644 --- a/arch/arm/mach-rockchip/rk3588/Kconfig +++ b/arch/arm/mach-rockchip/rk3588/Kconfig @@ -164,8 +164,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3588"
-config SYS_MALLOC_F_LEN - default 0x80000 +config ROCKCHIP_COMMON_STACK_ADDR + default y + +config TEXT_BASE + default 0x00a00000
source board/edgeble/neural-compute-module-6/Kconfig source board/friendlyelec/nanopc-t6-rk3588/Kconfig diff --git a/configs/evb-rk3588_defconfig b/configs/evb-rk3588_defconfig index 8a6aa91cb29a..c8db04c076ef 100644 --- a/configs/evb-rk3588_defconfig +++ b/configs/evb-rk3588_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-evb1-v10" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_EVB_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-evb1-v10.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopc-t6-rk3588_defconfig b/configs/nanopc-t6-rk3588_defconfig index 760993220929..5c7bc0b71968 100644 --- a/configs/nanopc-t6-rk3588_defconfig +++ b/configs/nanopc-t6-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-nanopc-t6" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_NANOPCT6_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -37,12 +29,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-nanopc-t6.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/neu6a-io-rk3588_defconfig b/configs/neu6a-io-rk3588_defconfig index d5301c630b2a..307a540f4249 100644 --- a/configs/neu6a-io-rk3588_defconfig +++ b/configs/neu6a-io-rk3588_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-edgeble-neu6a-io" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_RK3588_NEU6=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -27,12 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-edgeble-neu6a-io.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y diff --git a/configs/neu6b-io-rk3588_defconfig b/configs/neu6b-io-rk3588_defconfig index b13c9b5db1b0..9ef2bb21fffa 100644 --- a/configs/neu6b-io-rk3588_defconfig +++ b/configs/neu6b-io-rk3588_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-edgeble-neu6b-io" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_RK3588_NEU6=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -27,12 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-edgeble-neu6b-io.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y diff --git a/configs/orangepi-5-plus-rk3588_defconfig b/configs/orangepi-5-plus-rk3588_defconfig index a58f96d57798..d6e23c154f15 100644 --- a/configs/orangepi-5-plus-rk3588_defconfig +++ b/configs/orangepi-5-plus-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-orangepi-5-plus" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_EVB_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -38,12 +30,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-orangepi-5-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/orangepi-5-rk3588s_defconfig b/configs/orangepi-5-rk3588s_defconfig index a9404c912ea3..e6b3da1dc593 100644 --- a/configs/orangepi-5-rk3588s_defconfig +++ b/configs/orangepi-5-rk3588s_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588s-orangepi-5" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_EVB_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -37,12 +29,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588s-orangepi-5.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/quartzpro64-rk3588_defconfig b/configs/quartzpro64-rk3588_defconfig index 9cc4eb02e089..b2a66d3f2db0 100644 --- a/configs/quartzpro64-rk3588_defconfig +++ b/configs/quartzpro64-rk3588_defconfig @@ -3,19 +3,11 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-quartzpro64" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZPRO64_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -33,12 +25,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-quartzpro64.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock5a-rk3588s_defconfig b/configs/rock5a-rk3588s_defconfig index efa7bcbdcda6..ebe2d4a2d810 100644 --- a/configs/rock5a-rk3588s_defconfig +++ b/configs/rock5a-rk3588s_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588s-rock-5a" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x1000000 CONFIG_TARGET_ROCK5A_RK3588=y -CONFIG_SPL_STACK=0x1000000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588s-rock-5a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock5b-rk3588_defconfig b/configs/rock5b-rk3588_defconfig index a0678ff1290c..58c7c44fb4f7 100644 --- a/configs/rock5b-rk3588_defconfig +++ b/configs/rock5b-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-rock-5b" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_ROCK5B_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -38,12 +30,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-rock-5b.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/turing-rk1-rk3588_defconfig b/configs/turing-rk1-rk3588_defconfig index 0f903cf6e8b9..07f7b848529e 100644 --- a/configs/turing-rk1-rk3588_defconfig +++ b/configs/turing-rk1-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-turing-rk1" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_TURINGRK1_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEBC0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -38,12 +30,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-turing-rk1.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y
On 2024/3/3 03:16, Jonas Karlman wrote:
Currently the following memory layout is typically used on RK3588: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ 3.5M, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) [ 10M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [11.5M, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 11.5M) with this layout.
However, on ROCK 5A the SPL stacks is overlapping: [ -X, 16M) - SPL pre-reloc stack (SPL_STACK) [15.5M, 16M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ -X, 16M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 15M, 16M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
Because bind and probe udevice instanses is allocated on the pre-reloc malloc heap, there is going to be an overlap when reloc malloc heap reaches close to 512 KiB of usage.
Migrate to use common bss, stack and malloc heap size and addresses to mitigate these limitations and allow for a larger U-Boot proper size.
Signed-off-by: Jonas Karlman jonas@kwiboo.se
Reviewed-by: Kever Yang kever.yang@rock-chips.com
Thanks, - Kever
arch/arm/mach-rockchip/rk3588/Kconfig | 7 +++++-- configs/evb-rk3588_defconfig | 13 ------------- configs/nanopc-t6-rk3588_defconfig | 13 ------------- configs/neu6a-io-rk3588_defconfig | 13 ------------- configs/neu6b-io-rk3588_defconfig | 13 ------------- configs/orangepi-5-plus-rk3588_defconfig | 13 ------------- configs/orangepi-5-rk3588s_defconfig | 13 ------------- configs/quartzpro64-rk3588_defconfig | 13 ------------- configs/rock5a-rk3588s_defconfig | 13 ------------- configs/rock5b-rk3588_defconfig | 13 ------------- configs/turing-rk1-rk3588_defconfig | 13 ------------- 11 files changed, 5 insertions(+), 132 deletions(-)
diff --git a/arch/arm/mach-rockchip/rk3588/Kconfig b/arch/arm/mach-rockchip/rk3588/Kconfig index a2193fbd41fe..1ce65566261b 100644 --- a/arch/arm/mach-rockchip/rk3588/Kconfig +++ b/arch/arm/mach-rockchip/rk3588/Kconfig @@ -164,8 +164,11 @@ config ROCKCHIP_STIMER_BASE config SYS_SOC default "rk3588"
-config SYS_MALLOC_F_LEN
- default 0x80000
+config ROCKCHIP_COMMON_STACK_ADDR
- default y
+config TEXT_BASE
default 0x00a00000
source board/edgeble/neural-compute-module-6/Kconfig source board/friendlyelec/nanopc-t6-rk3588/Kconfig
diff --git a/configs/evb-rk3588_defconfig b/configs/evb-rk3588_defconfig index 8a6aa91cb29a..c8db04c076ef 100644 --- a/configs/evb-rk3588_defconfig +++ b/configs/evb-rk3588_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-evb1-v10" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_EVB_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-evb1-v10.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/nanopc-t6-rk3588_defconfig b/configs/nanopc-t6-rk3588_defconfig index 760993220929..5c7bc0b71968 100644 --- a/configs/nanopc-t6-rk3588_defconfig +++ b/configs/nanopc-t6-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-nanopc-t6" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_NANOPCT6_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -37,12 +29,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-nanopc-t6.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/neu6a-io-rk3588_defconfig b/configs/neu6a-io-rk3588_defconfig index d5301c630b2a..307a540f4249 100644 --- a/configs/neu6a-io-rk3588_defconfig +++ b/configs/neu6a-io-rk3588_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-edgeble-neu6a-io" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_RK3588_NEU6=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -27,12 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-edgeble-neu6a-io.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y diff --git a/configs/neu6b-io-rk3588_defconfig b/configs/neu6b-io-rk3588_defconfig index b13c9b5db1b0..9ef2bb21fffa 100644 --- a/configs/neu6b-io-rk3588_defconfig +++ b/configs/neu6b-io-rk3588_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-edgeble-neu6b-io" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_RK3588_NEU6=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -27,12 +19,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-edgeble-neu6b-io.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x20000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y diff --git a/configs/orangepi-5-plus-rk3588_defconfig b/configs/orangepi-5-plus-rk3588_defconfig index a58f96d57798..d6e23c154f15 100644 --- a/configs/orangepi-5-plus-rk3588_defconfig +++ b/configs/orangepi-5-plus-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-orangepi-5-plus" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_EVB_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -38,12 +30,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-orangepi-5-plus.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/orangepi-5-rk3588s_defconfig b/configs/orangepi-5-rk3588s_defconfig index a9404c912ea3..e6b3da1dc593 100644 --- a/configs/orangepi-5-rk3588s_defconfig +++ b/configs/orangepi-5-rk3588s_defconfig @@ -2,22 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588s-orangepi-5" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_EVB_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -37,12 +29,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588s-orangepi-5.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/quartzpro64-rk3588_defconfig b/configs/quartzpro64-rk3588_defconfig index 9cc4eb02e089..b2a66d3f2db0 100644 --- a/configs/quartzpro64-rk3588_defconfig +++ b/configs/quartzpro64-rk3588_defconfig @@ -3,19 +3,11 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-quartzpro64" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_QUARTZPRO64_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -33,12 +25,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-quartzpro64.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock5a-rk3588s_defconfig b/configs/rock5a-rk3588s_defconfig index efa7bcbdcda6..ebe2d4a2d810 100644 --- a/configs/rock5a-rk3588s_defconfig +++ b/configs/rock5a-rk3588s_defconfig @@ -2,19 +2,11 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_DEFAULT_DEVICE_TREE="rk3588s-rock-5a" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x1000000 CONFIG_TARGET_ROCK5A_RK3588=y -CONFIG_SPL_STACK=0x1000000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 @@ -30,12 +22,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588s-rock-5a.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y diff --git a/configs/rock5b-rk3588_defconfig b/configs/rock5b-rk3588_defconfig index a0678ff1290c..58c7c44fb4f7 100644 --- a/configs/rock5b-rk3588_defconfig +++ b/configs/rock5b-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-rock-5b" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_ROCK5B_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEB50000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -38,12 +30,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-rock-5b.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y diff --git a/configs/turing-rk1-rk3588_defconfig b/configs/turing-rk1-rk3588_defconfig index 0f903cf6e8b9..07f7b848529e 100644 --- a/configs/turing-rk1-rk3588_defconfig +++ b/configs/turing-rk1-rk3588_defconfig @@ -3,22 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_HAS_NONCACHED_MEMORY=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y -CONFIG_TEXT_BASE=0x00a00000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_SF_DEFAULT_SPEED=24000000 CONFIG_SF_DEFAULT_MODE=0x2000 CONFIG_DEFAULT_DEVICE_TREE="rk3588-turing-rk1" CONFIG_ROCKCHIP_RK3588=y -CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y CONFIG_ROCKCHIP_SPI_IMAGE=y CONFIG_SPL_SERIAL=y -CONFIG_SPL_STACK_R_ADDR=0x600000 CONFIG_TARGET_TURINGRK1_RK3588=y -CONFIG_SPL_STACK=0x400000 CONFIG_DEBUG_UART_BASE=0xFEBC0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y @@ -38,12 +30,7 @@ CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588-turing-rk1.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x40000 CONFIG_SPL_PAD_TO=0x7f8000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x4000000 -CONFIG_SPL_BSS_MAX_SIZE=0x4000 # CONFIG_SPL_RAW_IMAGE_SUPPORT is not set -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SPL_STACK_R=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 CONFIG_SPL_ATF=y
participants (2)
-
Jonas Karlman -
Kever Yang