From: Patrick Delaunay patrick.delaunay@st.com

This patch adds pinctrl/GPIO driver for STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander. STMFX is an I2C slave controller, offering up to 24 GPIOs. The driver relies on UCLASS_PINCTRL and UCLASS_GPIO.

Signed-off-by: Patrick Delaunay patrick.delaunay@st.com Signed-off-by: Patrice Chotard patrice.chotard@st.com ---

drivers/pinctrl/Kconfig | 19 ++ drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-stmfx.c | 431 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 451 insertions(+) create mode 100644 drivers/pinctrl/pinctrl-stmfx.c

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index be709f73d7df..a0ac167d145a 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -209,6 +209,25 @@ config PINCTRL_STM32 the GPIO definitions and pin control functions for each available multiplex function.

+config PINCTRL_STMFX + bool "STMicroelectronics STMFX I2C GPIO expander pinctrl driver" + depends on DM && PINCTRL_FULL + help + I2C driver for STMicroelectronics Multi-Function eXpander (STMFX) + GPIO expander. + Supports pin multiplexing control on stm32 SoCs. + + The driver is controlled by a device tree node which contains both + the GPIO definitions and pin control functions for each available + multiplex function. + +config SPL_PINCTRL_STMFX + bool "STMicroelectronics STMFX I2C GPIO expander pinctrl driver in SPL" + depends on SPL_PINCTRL_FULL + help + This option is an SPL-variant of the SPL_PINCTRL_STMFX option. + See the help of PINCTRL_STMFX for details. + config ASPEED_AST2500_PINCTRL bool "Aspeed AST2500 pin control driver" depends on DM && PINCTRL_GENERIC && ASPEED_AST2500 diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index e2c2b159d8c8..4b080b74dcd1 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -22,4 +22,5 @@ obj-$(CONFIG_ARCH_MVEBU) += mvebu/ obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o obj-$(CONFIG_PINCTRL_STI) += pinctrl-sti.o obj-$(CONFIG_PINCTRL_STM32) += pinctrl_stm32.o +obj-$(CONFIG_$(SPL_)PINCTRL_STMFX) += pinctrl-stmfx.o obj-y += broadcom/ diff --git a/drivers/pinctrl/pinctrl-stmfx.c b/drivers/pinctrl/pinctrl-stmfx.c new file mode 100644 index 000000000000..5431df9813a1 --- /dev/null +++ b/drivers/pinctrl/pinctrl-stmfx.c @@ -0,0 +1,431 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018, STMicroelectronics - All Rights Reserved + * + * Driver for STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander + * based on Linux driver : pinctrl/pinctrl-stmfx.c + */ +#include <common.h> +#include <dm.h> +#include <i2c.h> +#include <asm/gpio.h> +#include <dm/device.h> +#include <dm/device-internal.h> +#include <dm/lists.h> +#include <dm/pinctrl.h> +#include <linux/bitfield.h> +#include <power/regulator.h> + +/* STMFX pins = GPIO[15:0] + aGPIO[7:0] */ +#define STMFX_MAX_GPIO 16 +#define STMFX_MAX_AGPIO 8 + +/* General */ +#define STMFX_REG_CHIP_ID 0x00 /* R */ +#define STMFX_REG_FW_VERSION_MSB 0x01 /* R */ +#define STMFX_REG_FW_VERSION_LSB 0x02 /* R */ +#define STMFX_REG_SYS_CTRL 0x40 /* RW */ + +/* MFX boot time is around 10ms, so after reset, we have to wait this delay */ +#define STMFX_BOOT_TIME_MS 10 + +/* GPIOs expander */ +/* GPIO_STATE1 0x10, GPIO_STATE2 0x11, GPIO_STATE3 0x12 */ +#define STMFX_REG_GPIO_STATE 0x10 /* R */ +/* GPIO_DIR1 0x60, GPIO_DIR2 0x61, GPIO_DIR3 0x63 */ +#define STMFX_REG_GPIO_DIR 0x60 /* RW */ +/* GPIO_TYPE1 0x64, GPIO_TYPE2 0x65, GPIO_TYPE3 0x66 */ +#define STMFX_REG_GPIO_TYPE 0x64 /* RW */ +/* GPIO_PUPD1 0x68, GPIO_PUPD2 0x69, GPIO_PUPD3 0x6A */ +#define STMFX_REG_GPIO_PUPD 0x68 /* RW */ +/* GPO_SET1 0x6C, GPO_SET2 0x6D, GPO_SET3 0x6E */ +#define STMFX_REG_GPO_SET 0x6C /* RW */ +/* GPO_CLR1 0x70, GPO_CLR2 0x71, GPO_CLR3 0x72 */ +#define STMFX_REG_GPO_CLR 0x70 /* RW */ + +/* STMFX_REG_CHIP_ID bitfields */ +#define STMFX_REG_CHIP_ID_MASK GENMASK(7, 0) + +/* STMFX_REG_SYS_CTRL bitfields */ +#define STMFX_REG_SYS_CTRL_GPIO_EN BIT(0) +#define STMFX_REG_SYS_CTRL_ALTGPIO_EN BIT(3) +#define STMFX_REG_SYS_CTRL_SWRST BIT(7) + +#define NR_GPIO_REGS 3 +#define NR_GPIOS_PER_REG 8 +#define get_reg(offset) ((offset) / NR_GPIOS_PER_REG) +#define get_shift(offset) ((offset) % NR_GPIOS_PER_REG) +#define get_mask(offset) (BIT(get_shift(offset))) + +struct stmfx_pinctrl { + struct udevice *gpio; +}; + +static int stmfx_read(struct udevice *dev, uint offset) +{ + return dm_i2c_reg_read(dev_get_parent(dev), offset); +} + +static int stmfx_write(struct udevice *dev, uint offset, unsigned int val) +{ + return dm_i2c_reg_write(dev_get_parent(dev), offset, val); +} + +static int stmfx_gpio_get(struct udevice *dev, unsigned int offset) +{ + u32 reg = STMFX_REG_GPIO_STATE + get_reg(offset); + u32 mask = get_mask(offset); + int ret; + + ret = stmfx_read(dev, reg); + + return ret < 0 ? ret : !!(ret & mask); +} + +static int stmfx_gpio_set(struct udevice *dev, unsigned int offset, int value) +{ + u32 reg = value ? STMFX_REG_GPO_SET : STMFX_REG_GPO_CLR; + u32 mask = get_mask(offset); + + return stmfx_write(dev, reg + get_reg(offset), mask); +} + +static int stmfx_gpio_get_function(struct udevice *dev, unsigned int offset) +{ + u32 reg = STMFX_REG_GPIO_DIR + get_reg(offset); + u32 mask = get_mask(offset); + int ret; + + ret = stmfx_read(dev, reg); + + if (ret < 0) + return ret; + /* On stmfx, gpio pins direction is (0)input, (1)output. */ + + return ret & mask ? GPIOF_OUTPUT : GPIOF_INPUT; +} + +static int stmfx_gpio_direction_input(struct udevice *dev, unsigned int offset) +{ + u32 reg = STMFX_REG_GPIO_DIR + get_reg(offset); + u32 mask = get_mask(offset); + int ret; + + ret = stmfx_read(dev, reg); + if (ret < 0) + return ret; + + ret &= ~mask; + + return stmfx_write(dev, reg, ret & ~mask); +} + +static int stmfx_gpio_direction_output(struct udevice *dev, + unsigned int offset, int value) +{ + u32 reg = STMFX_REG_GPIO_DIR + get_reg(offset); + u32 mask = get_mask(offset); + int ret; + + ret = stmfx_gpio_set(dev, offset, value); + if (ret < 0) + return ret; + + ret = stmfx_read(dev, reg); + if (ret < 0) + return ret; + + return stmfx_write(dev, reg, ret | mask); +} + +static int stmfx_gpio_probe(struct udevice *dev) +{ + struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev); + struct ofnode_phandle_args args; + u8 sys_ctrl; + + uc_priv->bank_name = "stmfx"; + uc_priv->gpio_count = STMFX_MAX_GPIO + STMFX_MAX_AGPIO; + if (!dev_read_phandle_with_args(dev, "gpio-ranges", + NULL, 3, 0, &args)) { + uc_priv->gpio_count = args.args[2]; + } + + /* enable GPIO function */ + sys_ctrl = STMFX_REG_SYS_CTRL_GPIO_EN; + if (uc_priv->gpio_count > STMFX_MAX_GPIO) + sys_ctrl |= STMFX_REG_SYS_CTRL_ALTGPIO_EN; + stmfx_write(dev, STMFX_REG_SYS_CTRL, sys_ctrl); + + return 0; +} + +static const struct dm_gpio_ops stmfx_gpio_ops = { + .set_value = stmfx_gpio_set, + .get_value = stmfx_gpio_get, + .get_function = stmfx_gpio_get_function, + .direction_input = stmfx_gpio_direction_input, + .direction_output = stmfx_gpio_direction_output, +}; + +U_BOOT_DRIVER(stmfx_gpio) = { + .name = "stmfx-gpio", + .id = UCLASS_GPIO, + .probe = stmfx_gpio_probe, + .ops = &stmfx_gpio_ops, +}; + +#if CONFIG_IS_ENABLED(PINCONF) +static const struct pinconf_param stmfx_pinctrl_conf_params[] = { + { "bias-disable", PIN_CONFIG_BIAS_DISABLE, 0 }, + { "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 0 }, + { "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 0 }, + { "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 0 }, + { "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 }, + { "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 }, + { "output-high", PIN_CONFIG_OUTPUT, 1 }, + { "output-low", PIN_CONFIG_OUTPUT, 0 }, +}; + +static int stmfx_pinctrl_set_pupd(struct udevice *dev, + unsigned int pin, u32 pupd) +{ + u8 reg = STMFX_REG_GPIO_PUPD + get_reg(pin); + u32 mask = get_mask(pin); + int ret; + + ret = stmfx_read(dev, reg); + if (ret < 0) + return ret; + ret = (ret & ~mask) | (pupd ? mask : 0); + + return stmfx_write(dev, reg, ret); +} + +static int stmfx_pinctrl_set_type(struct udevice *dev, + unsigned int pin, u32 type) +{ + u8 reg = STMFX_REG_GPIO_TYPE + get_reg(pin); + u32 mask = get_mask(pin); + int ret; + + ret = stmfx_read(dev, reg); + if (ret < 0) + return ret; + ret = (ret & ~mask) | (type ? mask : 0); + + return stmfx_write(dev, reg, ret); +} + +static int stmfx_pinctrl_conf_set(struct udevice *dev, unsigned int pin, + unsigned int param, unsigned int arg) +{ + int ret, dir; + struct stmfx_pinctrl *plat = dev_get_platdata(dev); + + dir = stmfx_gpio_get_function(plat->gpio, pin); + + if (dir < 0) + return dir; + + switch (param) { + case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: + case PIN_CONFIG_BIAS_DISABLE: + case PIN_CONFIG_BIAS_PULL_DOWN: + ret = stmfx_pinctrl_set_pupd(dev, pin, 0); + break; + case PIN_CONFIG_BIAS_PULL_UP: + ret = stmfx_pinctrl_set_pupd(dev, pin, 1); + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + if (dir == GPIOF_OUTPUT) + ret = stmfx_pinctrl_set_type(dev, pin, 1); + else + ret = stmfx_pinctrl_set_type(dev, pin, 0); + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + if (dir == GPIOF_OUTPUT) + ret = stmfx_pinctrl_set_type(dev, pin, 0); + else + ret = stmfx_pinctrl_set_type(dev, pin, 1); + break; + case PIN_CONFIG_OUTPUT: + ret = stmfx_gpio_direction_output(plat->gpio, pin, arg); + break; + default: + return -ENOTSUPP; + } + + return ret; +} +#endif + +static int stmfx_pinctrl_get_pins_count(struct udevice *dev) +{ + struct stmfx_pinctrl *plat = dev_get_platdata(dev); + struct gpio_dev_priv *uc_priv; + + uc_priv = dev_get_uclass_priv(plat->gpio); + + return uc_priv->gpio_count; +} + +/* + * STMFX pins[15:0] are called "gpio[15:0]" + * and STMFX pins[23:16] are called "agpio[7:0]" + */ +#define MAX_PIN_NAME_LEN 7 +static char pin_name[MAX_PIN_NAME_LEN]; +static const char *stmfx_pinctrl_get_pin_name(struct udevice *dev, + unsigned int selector) +{ + if (selector < STMFX_MAX_GPIO) + snprintf(pin_name, MAX_PIN_NAME_LEN, "gpio%u", selector); + else + snprintf(pin_name, MAX_PIN_NAME_LEN, "agpio%u", selector - 16); + return pin_name; +} + +static int stmfx_pinctrl_get_pin_muxing(struct udevice *dev, + unsigned int selector, + char *buf, int size) +{ + struct stmfx_pinctrl *plat = dev_get_platdata(dev); + int func; + + func = stmfx_gpio_get_function(plat->gpio, selector); + if (func < 0) + return func; + + snprintf(buf, size, "%s", func == GPIOF_INPUT ? "input" : "output"); + + return 0; +} + +static int stmfx_pinctrl_bind(struct udevice *dev) +{ + struct stmfx_pinctrl *plat = dev_get_platdata(dev); + + return device_bind_driver_to_node(dev->parent, + "stmfx-gpio", "stmfx-gpio", + dev_ofnode(dev), &plat->gpio); +}; + +static int stmfx_pinctrl_probe(struct udevice *dev) +{ + struct stmfx_pinctrl *plat = dev_get_platdata(dev); + + return device_probe(plat->gpio); +}; + +const struct pinctrl_ops stmfx_pinctrl_ops = { + .get_pins_count = stmfx_pinctrl_get_pins_count, + .get_pin_name = stmfx_pinctrl_get_pin_name, + .set_state = pinctrl_generic_set_state, + .get_pin_muxing = stmfx_pinctrl_get_pin_muxing, +#if CONFIG_IS_ENABLED(PINCONF) + .pinconf_set = stmfx_pinctrl_conf_set, + .pinconf_num_params = ARRAY_SIZE(stmfx_pinctrl_conf_params), + .pinconf_params = stmfx_pinctrl_conf_params, +#endif +}; + +static const struct udevice_id stmfx_pinctrl_match[] = { + { .compatible = "st,stmfx-0300-pinctrl", }, +}; + +U_BOOT_DRIVER(stmfx_pinctrl) = { + .name = "stmfx-pinctrl", + .id = UCLASS_PINCTRL, + .of_match = of_match_ptr(stmfx_pinctrl_match), + .bind = stmfx_pinctrl_bind, + .probe = stmfx_pinctrl_probe, + .ops = &stmfx_pinctrl_ops, + .platdata_auto_alloc_size = sizeof(struct stmfx_pinctrl), +}; + +static int stmfx_chip_init(struct udevice *dev) +{ + u8 id; + u8 version[2]; + int ret; + struct dm_i2c_chip *chip = dev_get_parent_platdata(dev); + + id = dm_i2c_reg_read(dev, STMFX_REG_CHIP_ID); + if (id < 0) { + dev_err(dev, "error reading chip id: %d\n", id); + return ret; + } + /* + * Check that ID is the complement of the I2C address: + * STMFX I2C address follows the 7-bit format (MSB), that's why + * client->addr is shifted. + * + * STMFX_I2C_ADDR| STMFX | Linux + * input pin | I2C device address | I2C device address + *--------------------------------------------------------- + * 0 | b: 1000 010x h:0x84 | 0x42 + * 1 | b: 1000 011x h:0x86 | 0x43 + */ + if (FIELD_GET(STMFX_REG_CHIP_ID_MASK, ~id) != (chip->chip_addr << 1)) { + dev_err(dev, "unknown chip id: %#x\n", id); + return -EINVAL; + } + + ret = dm_i2c_read(dev, STMFX_REG_FW_VERSION_MSB, + version, sizeof(version)); + if (ret) { + dev_err(dev, "error reading fw version: %d\n", ret); + return ret; + } + + dev_info(dev, "STMFX id: %#x, fw version: %x.%02x\n", + id, version[0], version[1]); + + ret = dm_i2c_reg_read(dev, STMFX_REG_SYS_CTRL); + + if (ret < 0) + return ret; + + ret = dm_i2c_reg_write(dev, STMFX_REG_SYS_CTRL, + ret | STMFX_REG_SYS_CTRL_SWRST); + if (ret) + return ret; + + mdelay(STMFX_BOOT_TIME_MS); + + return ret; +} + +static int stmfx_probe(struct udevice *dev) +{ + struct udevice *vdd; + int ret; + + ret = device_get_supply_regulator(dev, "vdd-supply", &vdd); + if (ret && ret != -ENOENT) { + dev_err(dev, "vdd regulator error:%d\n", ret); + return ret; + } + if (!ret) { + ret = regulator_set_enable(vdd, true); + if (ret) { + dev_err(dev, "vdd enable failed: %d\n", ret); + return ret; + } + } + + return stmfx_chip_init(dev); +} + +static const struct udevice_id stmfx_match[] = { + { .compatible = "st,stmfx-0300", }, +}; + +U_BOOT_DRIVER(stmfx) = { + .name = "stmfx", + .id = UCLASS_I2C_GENERIC, + .of_match = of_match_ptr(stmfx_match), + .probe = stmfx_probe, + .bind = dm_scan_fdt_dev, +};

In order to insure that hog GPIOs are configured early during the boot process, force all pinctrl driver probing in board_init().

Signed-off-by: Patrick Delaunay patrick.delaunay@st.com Signed-off-by: Patrice Chotard patrice.chotard@st.com ---

board/st/stm32mp1/stm32mp1.c | 9 +++++++++ 1 file changed, 9 insertions(+)

diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c index 253094e6b418..7b3383547b1c 100644 --- a/board/st/stm32mp1/stm32mp1.c +++ b/board/st/stm32mp1/stm32mp1.c @@ -372,9 +372,18 @@ int board_late_init(void) /* board dependent setup after realloc */ int board_init(void) { + struct udevice *dev; + /* address of boot parameters */ gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;

+ /* probe all PINCTRL for hog */ + for (uclass_first_device(UCLASS_PINCTRL, &dev); + dev; + uclass_next_device(&dev)) { + pr_debug("probe pincontrol = %s\n", dev->name); + } + if (IS_ENABLED(CONFIG_LED)) led_default_state();