Add a function to look up a property which is a phandle in a node, and another to read a fixed-length integer array from an fdt property. Also add a function to read boolean properties, although there is no actual boolean type in U-Boot.

Signed-off-by: Simon Glass sjg@chromium.org Acked-by: Gerald Van Baren vanbaren@cideas.com Acked-by: Stephen Warren swarren@nvidia.com ---

include/fdtdec.h | 39 +++++++++++++++++++++++++++++++ lib/fdtdec.c | 67 ++++++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 106 insertions(+), 0 deletions(-)

diff --git a/include/fdtdec.h b/include/fdtdec.h index 01badd4..047f603 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -188,3 +188,42 @@ int fdtdec_find_aliases_for_id(const void *blob, const char *name, * @return compatible string for that id */ const char *fdtdec_get_compatible(enum fdt_compat_id id); + +/* Look up a phandle and follow it to its node. Then return the offset + * of that node. + * + * @param blob FDT blob + * @param node node to examine + * @param prop_name name of property to find + * @return node offset if found, -ve error code on error + */ +int fdtdec_lookup_phandle(const void *blob, int node, const char *prop_name); + +/** + * Look up a property in a node and return its contents in an integer + * array of given length. The property must have at least enough data for + * the array (4*count bytes). It may have more, but this will be ignored. + * + * @param blob FDT blob + * @param node node to examine + * @param prop_name name of property to find + * @param array array to fill with data + * @param count number of array elements + * @return 0 if ok, or -FDT_ERR_NOTFOUND if the property is not found, + * or -FDT_ERR_BADLAYOUT if not enough data + */ +int fdtdec_get_int_array(const void *blob, int node, const char *prop_name, + u32 *array, int count); + +/** + * Look up a boolean property in a node and return it. + * + * A boolean properly is true if present in the device tree and false if not + * present, regardless of its value. + * + * @param blob FDT blob + * @param node node to examine + * @param prop_name name of property to find + * @return 1 if the properly is present; 0 if it isn't present + */ +int fdtdec_get_bool(const void *blob, int node, const char *prop_name); diff --git a/lib/fdtdec.c b/lib/fdtdec.c index 846ec3f..977528b 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -269,3 +269,70 @@ int fdtdec_check_fdt(void) "binary or define CONFIG_OF_EMBED\n"); return 0; } + +int fdtdec_lookup_phandle(const void *blob, int node, const char *prop_name) +{ + const u32 *phandle; + int lookup; + + phandle = fdt_getprop(blob, node, prop_name, NULL); + if (!phandle) + return -FDT_ERR_NOTFOUND; + + lookup = fdt_node_offset_by_phandle(blob, fdt32_to_cpu(*phandle)); + return lookup; +} + +/** + * Look up a property in a node and check that it has a minimum length. + * + * @param blob FDT blob + * @param node node to examine + * @param prop_name name of property to find + * @param min_len minimum property length in bytes + * @param err 0 if ok, or -FDT_ERR_NOTFOUND if the property is not + found, or -FDT_ERR_BADLAYOUT if not enough data + * @return pointer to cell, which is only valid if err == 0 + */ +static const void *get_prop_check_min_len(const void *blob, int node, + const char *prop_name, int min_len, int *err) +{ + const void *cell; + int len; + + debug("%s: %s\n", __func__, prop_name); + cell = fdt_getprop(blob, node, prop_name, &len); + if (!cell) + *err = -FDT_ERR_NOTFOUND; + else if (len < min_len) + *err = -FDT_ERR_BADLAYOUT; + else + *err = 0; + return cell; +} + +int fdtdec_get_int_array(const void *blob, int node, const char *prop_name, + u32 *array, int count) +{ + const u32 *cell; + int i, err = 0; + + debug("%s: %s\n", __func__, prop_name); + cell = get_prop_check_min_len(blob, node, prop_name, + sizeof(u32) * count, &err); + if (!err) { + for (i = 0; i < count; i++) + array[i] = fdt32_to_cpu(cell[i]); + } + return err; +} + +int fdtdec_get_bool(const void *blob, int node, const char *prop_name) +{ + const s32 *cell; + int len; + + debug("%s: %s\n", __func__, prop_name); + cell = fdt_getprop(blob, node, prop_name, &len); + return cell != NULL; +}

This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git

Signed-off-by: Simon Glass sjg@chromium.org ---

arch/arm/dts/skeleton.dtsi | 13 +++++++++++++ 1 files changed, 13 insertions(+), 0 deletions(-) create mode 100644 arch/arm/dts/skeleton.dtsi

diff --git a/arch/arm/dts/skeleton.dtsi b/arch/arm/dts/skeleton.dtsi new file mode 100644 index 0000000..b41d241 --- /dev/null +++ b/arch/arm/dts/skeleton.dtsi @@ -0,0 +1,13 @@ +/* + * Skeleton device tree; the bare minimum needed to boot; just include and + * add a compatible value. The bootloader will typically populate the memory + * node. + */ + +/ { + #address-cells = <1>; + #size-cells = <1>; + chosen { }; + aliases { }; + memory { device_type = "memory"; reg = <0 0>; }; +};

This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git

Signed-off-by: Simon Glass sjg@chromium.org ---

board/nvidia/dts/tegra2-seaboard.dts | 36 ++++++++++++++++++++++++++++++++++ 1 files changed, 36 insertions(+), 0 deletions(-) create mode 100644 board/nvidia/dts/tegra2-seaboard.dts

diff --git a/board/nvidia/dts/tegra2-seaboard.dts b/board/nvidia/dts/tegra2-seaboard.dts new file mode 100644 index 0000000..dde5d03 --- /dev/null +++ b/board/nvidia/dts/tegra2-seaboard.dts @@ -0,0 +1,36 @@ +/dts-v1/; + +/memreserve/ 0x1c000000 0x04000000; +/include/ ARCH_CPU_DTS + +/ { + model = "NVIDIA Seaboard"; + compatible = "nvidia,seaboard", "nvidia,tegra20"; + + chosen { + bootargs = "vmalloc=192M video=tegrafb console=ttyS0,115200n8 root=/dev/mmcblk1p3 rw rootwait"; + }; + + memory { + device_type = "memory"; + reg = < 0x00000000 0x40000000 >; + }; + + serial@70006300 { + clock-frequency = < 216000000 >; + }; + + sdhci@c8000400 { + cd-gpios = <&gpio 69 0>; /* gpio PI5 */ + wp-gpios = <&gpio 57 0>; /* gpio PH1 */ + power-gpios = <&gpio 70 0>; /* gpio PI6 */ + }; + + sdhci@c8000600 { + support-8bit; + }; + + usb@c5000000 { + nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */ + }; +};

This file is taken from the Linux mailing list.

Signed-off-by: Simon Glass sjg@chromium.org ---

doc/device-tree-bindings/usb/tegra-usb.txt | 13 +++++++++++++ 1 files changed, 13 insertions(+), 0 deletions(-) create mode 100644 doc/device-tree-bindings/usb/tegra-usb.txt

diff --git a/doc/device-tree-bindings/usb/tegra-usb.txt b/doc/device-tree-bindings/usb/tegra-usb.txt new file mode 100644 index 0000000..035d63d --- /dev/null +++ b/doc/device-tree-bindings/usb/tegra-usb.txt @@ -0,0 +1,13 @@ +Tegra SOC USB controllers + +The device node for a USB controller that is part of a Tegra +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "nvidia,tegra20-ehci" for USB controllers + used in host mode. + - phy_type : Should be one of "ulpi" or "utmi". + - nvidia,vbus-gpio : If present, specifies a gpio that needs to be + activated for the bus to be powered.

Add the definition of the oscillator clock frequency.

Signed-off-by: Simon Glass sjg@chromium.org --- Changes in v6: - Add new patch to bring in clock bindings to seaboard

board/nvidia/dts/tegra2-seaboard.dts | 10 ++++++++++ 1 files changed, 10 insertions(+), 0 deletions(-)

diff --git a/board/nvidia/dts/tegra2-seaboard.dts b/board/nvidia/dts/tegra2-seaboard.dts index dde5d03..87f58fb 100644 --- a/board/nvidia/dts/tegra2-seaboard.dts +++ b/board/nvidia/dts/tegra2-seaboard.dts @@ -16,6 +16,16 @@ reg = < 0x00000000 0x40000000 >; };

+ clocks { + osc { + clock-frequency = <12000000>; + }; + }; + + clock@60006000 { + clocks = <&osc>; + }; + serial@70006300 { clock-frequency = < 216000000 >; };

We set up two USB ports, one of which can be host or device. For some reason the kernel version does enable both ports.

Signed-off-by: Simon Glass sjg@chromium.org --- Changes in v2: - Remove 0x from fdt aliases - Use "okay" instead of "ok" for fdt node status

Changes in v3: - Disable USB2 which is not used on Seaboard - Fix device tree indenting with tabs instead of spaces - Remove "okay" from nodes since this is the default anyway

Changes in v5: - Remove support-host-mode property

Changes in v6: - Remove dr_mode properties from SOC .dtsi file and move to boards

board/nvidia/dts/tegra2-seaboard.dts | 11 +++++++++++ 1 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/board/nvidia/dts/tegra2-seaboard.dts b/board/nvidia/dts/tegra2-seaboard.dts index 87f58fb..4fbb252 100644 --- a/board/nvidia/dts/tegra2-seaboard.dts +++ b/board/nvidia/dts/tegra2-seaboard.dts @@ -11,6 +11,12 @@ bootargs = "vmalloc=192M video=tegrafb console=ttyS0,115200n8 root=/dev/mmcblk1p3 rw rootwait"; };

+ aliases { + /* This defines the order of our USB ports */ + usb0 = "/usb@c5008000"; + usb1 = "/usb@c5000000"; + }; + memory { device_type = "memory"; reg = < 0x00000000 0x40000000 >; @@ -42,5 +48,10 @@

usb@c5000000 { nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */ + dr_mode = "otg"; + }; + + usb@c5004000 { + status = "disabled"; }; };

A common requirement is to find the clock ID for a peripheral. This is the second cell of the 'clocks' property (the first being the phandle itself).

Signed-off-by: Simon Glass sjg@chromium.org --- Changes in v4: - Add fdtdec function to return peripheral ID

Changes in v6: - Move peripheral decode function into Tegra's clock.c

arch/arm/cpu/armv7/tegra2/clock.c | 19 +++++++++++++++++++ arch/arm/include/asm/arch-tegra2/clock.h | 13 +++++++++++++ 2 files changed, 32 insertions(+), 0 deletions(-)

diff --git a/arch/arm/cpu/armv7/tegra2/clock.c b/arch/arm/cpu/armv7/tegra2/clock.c index 11d2346..ffbfc28 100644 --- a/arch/arm/cpu/armv7/tegra2/clock.c +++ b/arch/arm/cpu/armv7/tegra2/clock.c @@ -28,6 +28,7 @@ #include <asm/arch/tegra2.h> #include <common.h> #include <div64.h> +#include <fdtdec.h>

/* * This is our record of the current clock rate of each clock. We don't @@ -918,6 +919,24 @@ void clock_ll_start_uart(enum periph_id periph_id) reset_set_enable(periph_id, 0); }

+ +int clock_decode_periph_id(const void *blob, int node) +{ + enum periph_id id; + int err, valid; + u32 cell[2]; + + err = fdtdec_get_int_array(blob, node, "clocks", cell, + ARRAY_SIZE(cell)); + if (err) + return -1; + id = cell[1]; + + valid = clock_periph_id_isvalid(id); + assert(valid); + return valid ? id : PERIPH_ID_NONE; +} + int clock_verify(void) { struct clk_pll *pll = get_pll(CLOCK_ID_PERIPH); diff --git a/arch/arm/include/asm/arch-tegra2/clock.h b/arch/arm/include/asm/arch-tegra2/clock.h index 080ef18..6b12c76 100644 --- a/arch/arm/include/asm/arch-tegra2/clock.h +++ b/arch/arm/include/asm/arch-tegra2/clock.h @@ -177,6 +177,7 @@ enum periph_id { PERIPH_ID_CRAM2,

PERIPH_ID_COUNT, + PERIPH_ID_NONE = -1, };

/* Converts a clock number to a clock register: 0=L, 1=H, 2=U */ @@ -355,6 +356,18 @@ unsigned clock_get_rate(enum clock_id clkid); */ void clock_ll_start_uart(enum periph_id periph_id);

+/** + * Decode a peripheral ID from a device tree node. + * + * This works by looking up the peripheral's 'clocks' node and reading out + * the second cell, which is the clock number / peripheral ID. + * + * @param blob FDT blob to use + * @param node Node to look at + * @return peripheral ID, or PERIPH_ID_NONE if none + */ +enum periph_id clock_decode_periph_id(const void *blob, int node); + /* * Checks that clocks are valid and prints a warning if not *

This adds basic support for the Tegra2 USB controller. Board files should call board_usb_init() to set things up.

Configuration is performed through the FDT, with aliases used to set the order of the ports, like this fragment:

aliases { /* This defines the order of our USB ports */ usb0 = "/usb@0xc5008000"; usb1 = "/usb@0xc5000000"; };

drivers/usb/host files ONLY: Acked-by: Remy Bohmer linux@bohmer.net Signed-off-by: Simon Glass sjg@chromium.org --- Changes in v2: - Decode USB VBUS GPIO from the fdt - Decode phy type differently (to match new kernel fdt) - Improve debug() printouts in case of failure to init USB - Remove non-fdt operation of USB, since it is not needed - Rename params to timing - Rename tegra20-usb to tegra20-ehcui (to match new kernel fdt) - Store entire fdt config in port list, not just register pointer

Changes in v3: - Remove usbparams properties from fdt and moved them to C code

Changes in v4: - Use peripheral clock node to obtain peripheral ID - Use updated fdtdec alias functiona to get USB aliases

Changes in v5: - Add additional debugging to report active USB ports - Allow any port to operate in otg mode - Correct PTS_MASK value to be unsigned - Implement new device tree properties - Remove checking of peripheral ID and try to use only device tree - Report error if phy clock does not start up

Changes in v6: - Use updated clock_decode_periph_id() function

arch/arm/cpu/armv7/tegra2/Makefile | 4 +- arch/arm/cpu/armv7/tegra2/usb.c | 460 +++++++++++++++++++++++++++++ arch/arm/include/asm/arch-tegra2/tegra2.h | 2 + arch/arm/include/asm/arch-tegra2/usb.h | 252 ++++++++++++++++ drivers/usb/host/Makefile | 1 + drivers/usb/host/ehci-tegra.c | 62 ++++ include/fdtdec.h | 1 + lib/fdtdec.c | 1 + 8 files changed, 782 insertions(+), 1 deletions(-) create mode 100644 arch/arm/cpu/armv7/tegra2/usb.c create mode 100644 arch/arm/include/asm/arch-tegra2/usb.h create mode 100644 drivers/usb/host/ehci-tegra.c

diff --git a/arch/arm/cpu/armv7/tegra2/Makefile b/arch/arm/cpu/armv7/tegra2/Makefile index f668a81..e9ac6c9 100644 --- a/arch/arm/cpu/armv7/tegra2/Makefile +++ b/arch/arm/cpu/armv7/tegra2/Makefile @@ -33,8 +33,10 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(SOC).o

SOBJS := lowlevel_init.o -COBJS := ap20.o board.o clock.o funcmux.o pinmux.o sys_info.o timer.o +COBJS-y := ap20.o board.o clock.o funcmux.o pinmux.o sys_info.o timer.o +COBJS-$(CONFIG_USB_EHCI_TEGRA) += usb.o

+COBJS := $(COBJS-y) SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))

diff --git a/arch/arm/cpu/armv7/tegra2/usb.c b/arch/arm/cpu/armv7/tegra2/usb.c new file mode 100644 index 0000000..c80de7f --- /dev/null +++ b/arch/arm/cpu/armv7/tegra2/usb.c @@ -0,0 +1,460 @@ +/* + * Copyright (c) 2011 The Chromium OS Authors. + * (C) Copyright 2010,2011 NVIDIA Corporation <www.nvidia.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm-generic/gpio.h> +#include <asm/arch/tegra2.h> +#include <asm/arch/clk_rst.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <asm/arch/pinmux.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/uart.h> +#include <asm/arch/usb.h> +#include <libfdt.h> +#include <fdtdec.h> + +enum { + USB_PORTS_MAX = 4, /* Maximum ports we allow */ +}; + +/* Parameters we need for USB */ +enum { + PARAM_DIVN, /* PLL FEEDBACK DIVIDer */ + PARAM_DIVM, /* PLL INPUT DIVIDER */ + PARAM_DIVP, /* POST DIVIDER (2^N) */ + PARAM_CPCON, /* BASE PLLC CHARGE Pump setup ctrl */ + PARAM_LFCON, /* BASE PLLC LOOP FILter setup ctrl */ + PARAM_ENABLE_DELAY_COUNT, /* PLL-U Enable Delay Count */ + PARAM_STABLE_COUNT, /* PLL-U STABLE count */ + PARAM_ACTIVE_DELAY_COUNT, /* PLL-U Active delay count */ + PARAM_XTAL_FREQ_COUNT, /* PLL-U XTAL frequency count */ + PARAM_DEBOUNCE_A_TIME, /* 10MS DELAY for BIAS_DEBOUNCE_A */ + PARAM_BIAS_TIME, /* 20US DELAY AFter bias cell op */ + + PARAM_COUNT +}; + +/* Possible port types (dual role mode) */ +enum dr_mode { + DR_MODE_NONE = 0, + DR_MODE_HOST, /* supports host operation */ + DR_MODE_DEVICE, /* supports device operation */ + DR_MODE_OTG, /* supports both */ +}; + +/* Information about a USB port */ +struct fdt_usb { + struct usb_ctlr *reg; /* address of registers in physical memory */ + unsigned utmi:1; /* 1 if port has external tranceiver, else 0 */ + unsigned enabled:1; /* 1 to enable, 0 to disable */ + unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */ + enum dr_mode dr_mode; /* dual role mode */ + enum periph_id periph_id;/* peripheral id */ + struct fdt_gpio_state vbus_gpio; /* GPIO for vbus enable */ +}; + +static struct fdt_usb port[USB_PORTS_MAX]; /* List of valid USB ports */ +static unsigned port_count; /* Number of available ports */ +static int port_current; /* Current port (-1 = none) */ + +/* + * This table has USB timing parameters for each Oscillator frequency we + * support. There are four sets of values: + * + * 1. PLLU configuration information (reference clock is osc/clk_m and + * PLLU-FOs are fixed at 12MHz/60MHz/480MHz). + * + * Reference frequency 13.0MHz 19.2MHz 12.0MHz 26.0MHz + * ---------------------------------------------------------------------- + * DIVN 960 (0x3c0) 200 (0c8) 960 (3c0h) 960 (3c0) + * DIVM 13 (0d) 4 (04) 12 (0c) 26 (1a) + * Filter frequency (MHz) 1 4.8 6 2 + * CPCON 1100b 0011b 1100b 1100b + * LFCON0 0 0 0 0 + * + * 2. PLL CONFIGURATION & PARAMETERS for different clock generators: + * + * Reference frequency 13.0MHz 19.2MHz 12.0MHz 26.0MHz + * --------------------------------------------------------------------------- + * PLLU_ENABLE_DLY_COUNT 02 (0x02) 03 (03) 02 (02) 04 (04) + * PLLU_STABLE_COUNT 51 (33) 75 (4B) 47 (2F) 102 (66) + * PLL_ACTIVE_DLY_COUNT 05 (05) 06 (06) 04 (04) 09 (09) + * XTAL_FREQ_COUNT 127 (7F) 187 (BB) 118 (76) 254 (FE) + * + * 3. Debounce values IdDig, Avalid, Bvalid, VbusValid, VbusWakeUp, and + * SessEnd. Each of these signals have their own debouncer and for each of + * those one out of two debouncing times can be chosen (BIAS_DEBOUNCE_A or + * BIAS_DEBOUNCE_B). + * + * The values of DEBOUNCE_A and DEBOUNCE_B are calculated as follows: + * 0xffff -> No debouncing at all + * <n> ms = <n> *1000 / (1/19.2MHz) / 4 + * + * So to program a 1 ms debounce for BIAS_DEBOUNCE_A, we have: + * BIAS_DEBOUNCE_A[15:0] = 1000 * 19.2 / 4 = 4800 = 0x12c0 + * + * We need to use only DebounceA for BOOTROM. We don't need the DebounceB + * values, so we can keep those to default. + * + * 4. The 20 microsecond delay after bias cell operation. + */ +static const unsigned usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = { + /* DivN, DivM, DivP, CPCON, LFCON, Delays Debounce, Bias */ + { 0x3C0, 0x0D, 0x00, 0xC, 0, 0x02, 0x33, 0x05, 0x7F, 0x7EF4, 5 }, + { 0x0C8, 0x04, 0x00, 0x3, 0, 0x03, 0x4B, 0x06, 0xBB, 0xBB80, 7 }, + { 0x3C0, 0x0C, 0x00, 0xC, 0, 0x02, 0x2F, 0x04, 0x76, 0x7530, 5 }, + { 0x3C0, 0x1A, 0x00, 0xC, 0, 0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 } +}; + +/* UTMIP Idle Wait Delay */ +static const u8 utmip_idle_wait_delay = 17; + +/* UTMIP Elastic limit */ +static const u8 utmip_elastic_limit = 16; + +/* UTMIP High Speed Sync Start Delay */ +static const u8 utmip_hs_sync_start_delay = 9; + +/* Put the port into host mode (this only works for OTG ports) */ +static void set_host_mode(struct fdt_usb *config) +{ + if (config->dr_mode == DR_MODE_OTG) { + /* Check whether remote host from USB1 is driving VBus */ + if (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS) + return; + + /* + * If not driving, we set the GPIO to enable VBUS. We assume + * that the pinmux is set up correctly for this. + */ + if (fdt_gpio_isvalid(&config->vbus_gpio)) { + fdtdec_setup_gpio(&config->vbus_gpio); + gpio_direction_output(config->vbus_gpio.gpio, 1); + debug("set_host_mode: GPIO %d high\n", + config->vbus_gpio.gpio); + } + } +} + +void usbf_reset_controller(struct fdt_usb *config, struct usb_ctlr *usbctlr) +{ + /* Reset the USB controller with 2us delay */ + reset_periph(config->periph_id, 2); + + /* + * Set USB1_NO_LEGACY_MODE to 1, Registers are accessible under + * base address + */ + if (config->has_legacy_mode) + setbits_le32(&usbctlr->usb1_legacy_ctrl, USB1_NO_LEGACY_MODE); + + /* Put UTMIP1/3 in reset */ + setbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET); + + /* Enable the UTMIP PHY */ + if (config->utmi) + setbits_le32(&usbctlr->susp_ctrl, UTMIP_PHY_ENB); + + /* + * TODO: where do we take the USB1 out of reset? The old code would + * take USB3 out of reset, but not USB1. This code doesn't do either. + */ +} + +/* set up the USB controller with the parameters provided */ +static int init_usb_controller(struct fdt_usb *config, + struct usb_ctlr *usbctlr, const u32 timing[]) +{ + u32 val; + int loop_count; + + clock_enable(config->periph_id); + + /* Reset the usb controller */ + usbf_reset_controller(config, usbctlr); + + /* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */ + clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN); + + /* Follow the crystal clock disable by >100ns delay */ + udelay(1); + + /* + * To Use the A Session Valid for cable detection logic, VBUS_WAKEUP + * mux must be switched to actually use a_sess_vld threshold. + */ + if (fdt_gpio_isvalid(&config->vbus_gpio)) { + clrsetbits_le32(&usbctlr->usb1_legacy_ctrl, + VBUS_SENSE_CTL_MASK, + VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT); + } + + /* + * PLL Delay CONFIGURATION settings. The following parameters control + * the bring up of the plls. + */ + val = readl(&usbctlr->utmip_misc_cfg1); + clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK, + timing[PARAM_STABLE_COUNT] << UTMIP_PLLU_STABLE_COUNT_SHIFT); + clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK, + timing[PARAM_ACTIVE_DELAY_COUNT] << + UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT); + writel(val, &usbctlr->utmip_misc_cfg1); + + /* Set PLL enable delay count and crystal frequency count */ + val = readl(&usbctlr->utmip_pll_cfg1); + clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK, + timing[PARAM_ENABLE_DELAY_COUNT] << + UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT); + clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK, + timing[PARAM_XTAL_FREQ_COUNT] << + UTMIP_XTAL_FREQ_COUNT_SHIFT); + writel(val, &usbctlr->utmip_pll_cfg1); + + /* Setting the tracking length time */ + clrsetbits_le32(&usbctlr->utmip_bias_cfg1, + UTMIP_BIAS_PDTRK_COUNT_MASK, + timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT); + + /* Program debounce time for VBUS to become valid */ + clrsetbits_le32(&usbctlr->utmip_debounce_cfg0, + UTMIP_DEBOUNCE_CFG0_MASK, + timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT); + + setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J); + + /* Disable battery charge enabling bit */ + setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG); + + clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE); + setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL); + + /* + * Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT + * Setting these fields, together with default values of the + * other fields, results in programming the registers below as + * follows: + * UTMIP_HSRX_CFG0 = 0x9168c000 + * UTMIP_HSRX_CFG1 = 0x13 + */ + + /* Set PLL enable delay count and Crystal frequency count */ + val = readl(&usbctlr->utmip_hsrx_cfg0); + clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK, + utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT); + clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK, + utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT); + writel(val, &usbctlr->utmip_hsrx_cfg0); + + /* Configure the UTMIP_HS_SYNC_START_DLY */ + clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1, + UTMIP_HS_SYNC_START_DLY_MASK, + utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT); + + /* Preceed the crystal clock disable by >100ns delay. */ + udelay(1); + + /* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */ + setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN); + + /* Finished the per-controller init. */ + + /* De-assert UTMIP_RESET to bring out of reset. */ + clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET); + + /* Wait for the phy clock to become valid in 100 ms */ + for (loop_count = 100000; loop_count != 0; loop_count--) { + if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID) + break; + udelay(1); + } + if (loop_count == 100000) + return -1; + + return 0; +} + +static void power_up_port(struct usb_ctlr *usbctlr) +{ + /* Deassert power down state */ + clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN | + UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN); + clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN | + UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN); +} + +static void config_clock(const u32 timing[]) +{ + clock_start_pll(CLOCK_ID_USB, + timing[PARAM_DIVM], timing[PARAM_DIVN], timing[PARAM_DIVP], + timing[PARAM_CPCON], timing[PARAM_LFCON]); +} + +/** + * Add a new USB port to the list of available ports. + * + * @param config USB port configuration + * @return 0 if ok, -1 if error (too many ports) + */ +static int add_port(struct fdt_usb *config, const u32 timing[]) +{ + struct usb_ctlr *usbctlr = config->reg; + + if (port_count == USB_PORTS_MAX) { + debug("tegrausb: Cannot register more than %d ports\n", + USB_PORTS_MAX); + return -1; + } + if (init_usb_controller(config, usbctlr, timing)) { + debug("tegrausb: Cannot init port\n"); + return -1; + } + if (config->utmi) { + /* Disable ICUSB FS/LS transceiver */ + clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1); + + /* Select UTMI parallel interface */ + clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, + PTS_UTMI << PTS_SHIFT); + clrbits_le32(&usbctlr->port_sc1, STS); + power_up_port(usbctlr); + } + port[port_count++] = *config; + + return 0; +} + +int tegrausb_start_port(unsigned portnum, u32 *hccr, u32 *hcor) +{ + struct usb_ctlr *usbctlr; + + if (portnum >= port_count) + return -1; + tegrausb_stop_port(); + set_host_mode(&port[portnum]); + + usbctlr = port[portnum].reg; + *hccr = (u32)&usbctlr->cap_length; + *hcor = (u32)&usbctlr->usb_cmd; + port_current = portnum; + return 0; +} + +int tegrausb_stop_port(void) +{ + struct usb_ctlr *usbctlr; + + if (port_current == -1) + return -1; + + usbctlr = port[port_current].reg; + + /* Stop controller */ + writel(0, &usbctlr->usb_cmd); + udelay(1000); + + /* Initiate controller reset */ + writel(2, &usbctlr->usb_cmd); + udelay(1000); + port_current = -1; + return 0; +} + +int fdt_decode_usb(const void *blob, int node, unsigned osc_frequency_mhz, + struct fdt_usb *config) +{ + const char *phy, *mode; + + config->reg = (struct usb_ctlr *)fdtdec_get_addr(blob, node, "reg"); + mode = fdt_getprop(blob, node, "dr_mode", NULL); + if (mode) { + if (0 == strcmp(mode, "host")) + config->dr_mode = DR_MODE_HOST; + else if (0 == strcmp(mode, "peripheral")) + config->dr_mode = DR_MODE_DEVICE; + else if (0 == strcmp(mode, "otg")) + config->dr_mode = DR_MODE_OTG; + else { + debug("%s: Cannot decode dr_mode '%s'\n", __func__, + mode); + return -FDT_ERR_NOTFOUND; + } + } else { + config->dr_mode = DR_MODE_HOST; + } + + phy = fdt_getprop(blob, node, "phy_type", NULL); + config->utmi = phy && 0 == strcmp("utmi", phy); + config->enabled = fdtdec_get_is_enabled(blob, node); + config->has_legacy_mode = fdtdec_get_bool(blob, node, + "nvidia,has-legacy-mode"); + config->periph_id = clock_decode_periph_id(blob, node); + if (config->periph_id == PERIPH_ID_NONE) { + debug("%s: Missing/invalid peripheral ID\n", __func__); + return -FDT_ERR_NOTFOUND; + } + fdtdec_decode_gpio(blob, node, "nvidia,vbus-gpio", &config->vbus_gpio); + debug("enabled=%d, legacy_mode=%d, utmi=%d, periph_id=%d, vbus=%d, " + "dr_mode=%d\n", config->enabled, config->has_legacy_mode, + config->utmi, config->periph_id, config->vbus_gpio.gpio, + config->dr_mode); + + return 0; +} + +int board_usb_init(const void *blob) +{ + struct fdt_usb config; + unsigned osc_freq = clock_get_rate(CLOCK_ID_OSC); + enum clock_osc_freq freq; + int node_list[USB_PORTS_MAX]; + int node, count, i; + + /* Set up the USB clocks correctly based on our oscillator frequency */ + freq = clock_get_osc_freq(); + config_clock(usb_pll[freq]); + + /* count may return <0 on error */ + count = fdtdec_find_aliases_for_id(blob, "usb", + COMPAT_NVIDIA_TEGRA20_USB, node_list, USB_PORTS_MAX); + for (i = 0; i < count; i++) { + debug("USB %d: ", i); + node = node_list[i]; + if (!node) + continue; + if (fdt_decode_usb(blob, node, osc_freq, &config)) { + debug("Cannot decode USB node %s\n", + fdt_get_name(blob, node, NULL)); + return -1; + } + + if (add_port(&config, usb_pll[freq])) + return -1; + set_host_mode(&config); + } + port_current = -1; + + return 0; +} diff --git a/arch/arm/include/asm/arch-tegra2/tegra2.h b/arch/arm/include/asm/arch-tegra2/tegra2.h index 8941443..baae2eb 100644 --- a/arch/arm/include/asm/arch-tegra2/tegra2.h +++ b/arch/arm/include/asm/arch-tegra2/tegra2.h @@ -41,6 +41,8 @@ #define TEGRA2_SPI_BASE (NV_PA_APB_MISC_BASE + 0xC380) #define NV_PA_PMC_BASE 0x7000E400 #define NV_PA_CSITE_BASE 0x70040000 +#define TEGRA_USB1_BASE 0xC5000000 +#define TEGRA_USB3_BASE 0xC5008000

#define TEGRA2_SDRC_CS0 NV_PA_SDRAM_BASE #define LOW_LEVEL_SRAM_STACK 0x4000FFFC diff --git a/arch/arm/include/asm/arch-tegra2/usb.h b/arch/arm/include/asm/arch-tegra2/usb.h new file mode 100644 index 0000000..638033b --- /dev/null +++ b/arch/arm/include/asm/arch-tegra2/usb.h @@ -0,0 +1,252 @@ +/* + * Copyright (c) 2011 The Chromium OS Authors. + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _TEGRA_USB_H_ +#define _TEGRA_USB_H_ + + +/* USB Controller (USBx_CONTROLLER_) regs */ +struct usb_ctlr { + /* 0x000 */ + uint id; + uint reserved0; + uint host; + uint device; + + /* 0x010 */ + uint txbuf; + uint rxbuf; + uint reserved1[2]; + + /* 0x020 */ + uint reserved2[56]; + + /* 0x100 */ + u16 cap_length; + u16 hci_version; + uint hcs_params; + uint hcc_params; + uint reserved3[5]; + + /* 0x120 */ + uint dci_version; + uint dcc_params; + uint reserved4[6]; + + /* 0x140 */ + uint usb_cmd; + uint usb_sts; + uint usb_intr; + uint frindex; + + /* 0x150 */ + uint reserved5; + uint periodic_list_base; + uint async_list_addr; + uint async_tt_sts; + + /* 0x160 */ + uint burst_size; + uint tx_fill_tuning; + uint reserved6; /* is this port_sc1 on some controllers? */ + uint icusb_ctrl; + + /* 0x170 */ + uint ulpi_viewport; + uint reserved7; + uint endpt_nak; + uint endpt_nak_enable; + + /* 0x180 */ + uint reserved; + uint port_sc1; + uint reserved8[6]; + + /* 0x1a0 */ + uint reserved9; + uint otgsc; + uint usb_mode; + uint endpt_setup_stat; + + /* 0x1b0 */ + uint reserved10[20]; + + /* 0x200 */ + uint reserved11[0x80]; + + /* 0x400 */ + uint susp_ctrl; + uint phy_vbus_sensors; + uint phy_vbus_wakeup_id; + uint phy_alt_vbus_sys; + + /* 0x410 */ + uint usb1_legacy_ctrl; + uint reserved12[3]; + + /* 0x420 */ + uint reserved13[56]; + + /* 0x500 */ + uint reserved14[64 * 3]; + + /* 0x800 */ + uint utmip_pll_cfg0; + uint utmip_pll_cfg1; + uint utmip_xcvr_cfg0; + uint utmip_bias_cfg0; + + /* 0x810 */ + uint utmip_hsrx_cfg0; + uint utmip_hsrx_cfg1; + uint utmip_fslsrx_cfg0; + uint utmip_fslsrx_cfg1; + + /* 0x820 */ + uint utmip_tx_cfg0; + uint utmip_misc_cfg0; + uint utmip_misc_cfg1; + uint utmip_debounce_cfg0; + + /* 0x830 */ + uint utmip_bat_chrg_cfg0; + uint utmip_spare_cfg0; + uint utmip_xcvr_cfg1; + uint utmip_bias_cfg1; +}; + + +/* USB1_LEGACY_CTRL */ +#define USB1_NO_LEGACY_MODE 1 + +#define VBUS_SENSE_CTL_SHIFT 1 +#define VBUS_SENSE_CTL_MASK (3 << VBUS_SENSE_CTL_SHIFT) +#define VBUS_SENSE_CTL_VBUS_WAKEUP 0 +#define VBUS_SENSE_CTL_AB_SESS_VLD_OR_VBUS_WAKEUP 1 +#define VBUS_SENSE_CTL_AB_SESS_VLD 2 +#define VBUS_SENSE_CTL_A_SESS_VLD 3 + +/* USBx_IF_USB_SUSP_CTRL_0 */ +#define UTMIP_PHY_ENB (1 << 12) +#define UTMIP_RESET (1 << 11) +#define USB_PHY_CLK_VALID (1 << 7) + +/* USBx_UTMIP_MISC_CFG1 */ +#define UTMIP_PLLU_STABLE_COUNT_SHIFT 6 +#define UTMIP_PLLU_STABLE_COUNT_MASK \ + (0xfff << UTMIP_PLLU_STABLE_COUNT_SHIFT) +#define UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT 18 +#define UTMIP_PLL_ACTIVE_DLY_COUNT_MASK \ + (0x1f << UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT) +#define UTMIP_PHY_XTAL_CLOCKEN (1 << 30) + +/* USBx_UTMIP_PLL_CFG1_0 */ +#define UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT 27 +#define UTMIP_PLLU_ENABLE_DLY_COUNT_MASK \ + (0xf << UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT) +#define UTMIP_XTAL_FREQ_COUNT_SHIFT 0 +#define UTMIP_XTAL_FREQ_COUNT_MASK 0xfff + +/* USBx_UTMIP_BIAS_CFG1_0 */ +#define UTMIP_BIAS_PDTRK_COUNT_SHIFT 3 +#define UTMIP_BIAS_PDTRK_COUNT_MASK \ + (0x1f << UTMIP_BIAS_PDTRK_COUNT_SHIFT) + +#define UTMIP_DEBOUNCE_CFG0_SHIFT 0 +#define UTMIP_DEBOUNCE_CFG0_MASK 0xffff + +/* USBx_UTMIP_TX_CFG0_0 */ +#define UTMIP_FS_PREAMBLE_J (1 << 19) + +/* USBx_UTMIP_BAT_CHRG_CFG0_0 */ +#define UTMIP_PD_CHRG 1 + +/* USBx_UTMIP_XCVR_CFG0_0 */ +#define UTMIP_XCVR_LSBIAS_SE (1 << 21) + +/* USBx_UTMIP_SPARE_CFG0_0 */ +#define FUSE_SETUP_SEL (1 << 3) + +/* USBx_UTMIP_HSRX_CFG0_0 */ +#define UTMIP_IDLE_WAIT_SHIFT 15 +#define UTMIP_IDLE_WAIT_MASK (0x1f << UTMIP_IDLE_WAIT_SHIFT) +#define UTMIP_ELASTIC_LIMIT_SHIFT 10 +#define UTMIP_ELASTIC_LIMIT_MASK \ + (0x1f << UTMIP_ELASTIC_LIMIT_SHIFT) + +/* USBx_UTMIP_HSRX_CFG0_1 */ +#define UTMIP_HS_SYNC_START_DLY_SHIFT 1 +#define UTMIP_HS_SYNC_START_DLY_MASK \ + (0xf << UTMIP_HS_SYNC_START_DLY_SHIFT) + +/* USBx_CONTROLLER_2_USB2D_ICUSB_CTRL_0 */ +#define IC_ENB1 (1 << 3) + +/* SB2_CONTROLLER_2_USB2D_PORTSC1_0 */ +#define PTS_SHIFT 30 +#define PTS_MASK (3U << PTS_SHIFT) +#define PTS_UTMI 0 +#define PTS_RESERVED 1 +#define PTS_ULP 2 +#define PTS_ICUSB_SER 3 + +#define STS (1 << 29) + +/* USBx_UTMIP_XCVR_CFG0_0 */ +#define UTMIP_FORCE_PD_POWERDOWN (1 << 14) +#define UTMIP_FORCE_PD2_POWERDOWN (1 << 16) +#define UTMIP_FORCE_PDZI_POWERDOWN (1 << 18) + +/* USBx_UTMIP_XCVR_CFG1_0 */ +#define UTMIP_FORCE_PDDISC_POWERDOWN (1 << 0) +#define UTMIP_FORCE_PDCHRP_POWERDOWN (1 << 2) +#define UTMIP_FORCE_PDDR_POWERDOWN (1 << 4) + +/* USB3_IF_USB_PHY_VBUS_SENSORS_0 */ +#define VBUS_VLD_STS (1 << 26) + + +/* Change the USB host port into host mode */ +void usb_set_host_mode(void); + +/* Setup USB on the board */ +int board_usb_init(const void *blob); + +/** + * Start up the given port number (ports are numbered from 0 on each board). + * This returns values for the appropriate hccr and hcor addresses to use for + * USB EHCI operations. + * + * @param portnum port number to start + * @param hccr returns start address of EHCI HCCR registers + * @param hcor returns start address of EHCI HCOR registers + * @return 0 if ok, -1 on error (generally invalid port number) + */ +int tegrausb_start_port(unsigned portnum, u32 *hccr, u32 *hcor); + +/** + * Stop the current port + * + * @return 0 if ok, -1 if no port was active + */ +int tegrausb_stop_port(void); + +#endif /* _TEGRA_USB_H_ */ diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 77e217f..a11cebb 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -47,6 +47,7 @@ COBJS-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o COBJS-$(CONFIG_USB_EHCI_KIRKWOOD) += ehci-kirkwood.o COBJS-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o +COBJS-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o COBJS-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o

COBJS := $(COBJS-y) diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c new file mode 100644 index 0000000..a7e105b --- /dev/null +++ b/drivers/usb/host/ehci-tegra.c @@ -0,0 +1,62 @@ +/* + * Copyright (c) 2009 NVIDIA Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <usb.h> + +#include "ehci.h" +#include "ehci-core.h" + +#include <asm/errno.h> +#include <asm/arch/usb.h> + + +/* + * Create the appropriate control structures to manage + * a new EHCI host controller. + */ +int ehci_hcd_init(void) +{ + u32 our_hccr, our_hcor; + + /* + * Select the first port, as we don't have a way of selecting others + * yet + */ + if (tegrausb_start_port(0, &our_hccr, &our_hcor)) + return -1; + + hccr = (struct ehci_hccr *)our_hccr; + hcor = (struct ehci_hcor *)our_hcor; + + return 0; +} + +/* + * Destroy the appropriate control structures corresponding + * the the EHCI host controller. + */ +int ehci_hcd_stop(void) +{ + tegrausb_stop_port(); + return 0; +} diff --git a/include/fdtdec.h b/include/fdtdec.h index 6c0a2d1..2ac8c9c 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -57,6 +57,7 @@ struct fdt_memory { */ enum fdt_compat_id { COMPAT_UNKNOWN, + COMPAT_NVIDIA_TEGRA20_USB, /* Tegra2 USB port */

COMPAT_COUNT, }; diff --git a/lib/fdtdec.c b/lib/fdtdec.c index c748cac..5f137a5 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -37,6 +37,7 @@ DECLARE_GLOBAL_DATA_PTR; #define COMPAT(id, name) name static const char * const compat_names[COMPAT_COUNT] = { COMPAT(UNKNOWN, "<none>"), + COMPAT(NVIDIA_TEGRA20_USB, "nvidia,tegra20-ehci"), };

const char *fdtdec_get_compatible(enum fdt_compat_id id)

All Tegra2 boards should include tegra2-common. This adds the required USB config to that file.

Signed-off-by: Simon Glass sjg@chromium.org --- Changes in v5: - Add CONFIG_EHCI_DCACHE which is needed for dcache operation - Drop unused CONFIG_USB_EHCI_DATA_ALIGN option

include/configs/tegra2-common.h | 10 ++++++++++ 1 files changed, 10 insertions(+), 0 deletions(-)

diff --git a/include/configs/tegra2-common.h b/include/configs/tegra2-common.h index e6f385f..266d0e5 100644 --- a/include/configs/tegra2-common.h +++ b/include/configs/tegra2-common.h @@ -84,6 +84,16 @@ #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 115200}

+/* + * This parameter affects a TXFILLTUNING field that controls how much data is + * sent to the latency fifo before it is sent to the wire. Without this + * parameter, the default (2) causes occasional Data Buffer Errors in OUT + * packets depending on the buffer address and size. + */ +#define CONFIG_USB_EHCI_TXFIFO_THRESH 10 +#define CONFIG_EHCI_IS_TDI +#define CONFIG_EHCI_DCACHE + /* include default commands */ #include <config_cmd_default.h>

This switches Seaboard over to use FDT for run-time config instead of CONFIG options. USB is the only user at present.

Signed-off-by: Simon Glass sjg@chromium.org --- Changes in v3: - Drop Tegra USB alignment patch as we will deal with this another way

Changes in v6: - Drop fdt alignment patch as we will handle this after generic reloc

include/configs/seaboard.h | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-)

diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index b6d9f7a..1dc775a 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -27,6 +27,11 @@ #include <asm/sizes.h> #include "tegra2-common.h"

+/* Enable fdt support for Seaboard. Flash the image in u-boot-dtb.bin */ +#define CONFIG_DEFAULT_DEVICE_TREE tegra2-seaboard +#define CONFIG_OF_CONTROL +#define CONFIG_OF_SEPARATE + /* High-level configuration options */ #define TEGRA2_SYSMEM "mem=384M@0M nvmem=128M@384M mem=512M@512M" #define V_PROMPT "Tegra2 (SeaBoard) # "