Hi, Gerrit!

Gerrit Van de Velde wrote:

Hi all,

I'm not sure if it's entirely on topic but here we go: We've been trying to set the local bus speed of the MPC8540 to 82MHz without much success until now. We're using Uboot 1.1.4 with our own board.c code mostly ripped from the 8540ADS board. In the code there's some info about a workaround for the DLL of te cpu:

/* * Errata LBC11. * Fix Local Bus clock glitch when DLL is enabled. * * If localbus freq is < 66Mhz, DLL bypass mode must be used. * If localbus freq is > 133Mhz, DLL can be safely enabled. * Between 66 and 133, the DLL is enabled with an override workaround. */

But actually, the 82Mhz is in between those values. In this code, the U-Boot stops working after the LCRR is assigned and doesn't even get to the udelay part (checked with printfs)

lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ Udelay(200);

Disabling or enabling has the same result, the clock speed of the bus has changed though to 82MHz (checked it with the scope).

Has anyone of you some pointers on what to check or what to try out?

Hmm, not really. I didn't run into the LBC11 Errata yet. I did some experiments with the LBC some time ago on 82MHz as well as on 166MHz when I did my UPM coding for the MPC8540 - no problems so far. See some code snippets below, YMMV using U-Boot:

MPC8540 code examples to illustrate the Local Bus Clock setup from my Linux 2.6.18 kernel module: -----8<-----

/* 0. map the phys area to be able to write the UPM RAM patterns*/ ecam_map.virt = ioremap_nocache(ecam_map.phys, ecam_map.size);

/* speed up the local bus */ /* immap->im_lbc.lcrr=0x00010002; */ /* 166MHz fast */ immap->im_lbc.lcrr=0x00030004; /* 83MHz slow */

/* LCRR * 0000 0000 0000 0001 0000 0000 0000 0010 0x00030004 * 0 DPY DLL bypass 0 DLL enabled * 1 reserved 0 * 2-3 BUFCMDC 00. 4 (doesn't matter) * 4-5 reserved 00 * 6-7 ECL Ext CAS latency 00. 4 (minimum) * 8-13 reserved 0000.00 * 14-15 EADC ext addr delay 01. 1 cycle (minimum) * 16-27 reserved 0000.0000.0000. * 28-31 CLKDIV CCB to LBC 0010 div by 2 */ /*local bus configuration register*/ immap->im_lbc.lbcr=0x00200000; /* LBCR * 0000 0000 0010 0000 0000 0000 0000 0000 0x00200000 * 0 LDIS local bus disable 0 enabled * 1-7 reserved 000.0000. * 8-9 BCTLC buf ctrl 00 W/#R control * 10 AHD addr hold disable 1 highspeed * 11-13 reserved 0.00 * 14 LPBSE parity 0 disabled * 15 EPAR parity 0. odd * 16-23 BMT bus monitor timing 0000.0000 default * 24-31 reserved 0000 */

/* 1. set up BRn and ORn registers */ /* set up BR4 and OR4 registers for 64k command io window */ immap->im_lbc.br4 = 0x00000000; /* clear br before touching or */ immap->im_lbc.or4 = (0x00000000-ECAM_FPGACMDSIZE)+0x6100; /*no bursts*/

//immap->im_lbc.or4 = 0xffff6100; /* 64kb, no bursts */ /* 1111 1111 1111 1111 0000 0001 0000 0000 */

immap->im_lbc.br4 = ECAM_FPGACMD+0x1881; /*ps=32bit, UPMA, set base and valid */ //immap->im_lbc.br4 = 0xfc101881; /* @fc01, PS=32bit, UPMA, set base and valid */ /* 1111 1100 0000 0000 0001 1000 1000 0001 */

/* set up CR5 and OR5 registers for 64k data io window */ /* clear valid bit, otherwise ORx is not programmable!!! */ immap->im_lbc.br5=0x00000000; #if BURST immap->im_lbc.or5 = (0x00000000-ECAM_FPGADATASIZE)+0x6000; /*bursts*/ //immap->im_lbc.or5 = 0xfff06000; /* 1MByte, bursts */ DBG("Bursts enabled!\n"); #else immap->im_lbc.or5 = (0x00000000-ECAM_FPGADATASIZE)+0x6100; /*bursts inhibited*/ //immap->im_lbc.or5 = 0xfff06100; /* 1MByte, bursts inhibited */ DBG("Bursts disabled!\n"); #endif /* default: 0xff006f67 */ /* OR5 * 1111 1111 0000 0000 0110 0000 0000 0111 0xff006816 * 00-16 AM address mask 0xff00.0 16 MBytes * 17-18 reserved?? 11 manual unclear! * 19 BCTLD buf ctrl disable 0. enabled * 20-22 reserved 000 * 23 BI burst inhibit 0. bursts allowed * 24-28 reserved 0000.0 * 29 TRLX timing relaxed 0 relax * 30 EHTR ext. hold time 0 extend * 31 EAD ext AL delay 0 delayes */ immap->im_lbc.br5 = ECAM_FPGADATA+0x1881; /* PS=32bit, UPMA, set base and valid */ //immap->im_lbc.br5=0xfc001881; /* @fc00, PS=32bit, UPMA, set base and valid */ /* BR5 * 1111 1100 0000 0000 0001 1000 1000 0001 0xfc001801 * 00-16 BA base address 0xfc00.0 * 17-18 reserved 00 * 19-20 PS port size 1.1 32bit * 21-22 DECC error checking 00 disabled * 23 WP Write Protect 0. r/w * 24-26 MSEL Machine Select 100 UPMA * 27 reserved 0. * 28-29 ATOM 00 no atomic oprtations * 30 reserved 0 * 31 V valid 1 valid */

-----8<-----

Good luck!

Clemens Koller _______________________________ R&D Imaging Devices Anagramm GmbH Rupert-Mayer-Str. 45/1 81379 Muenchen Germany

http://www.anagramm.de Phone: +49-89-741518-50 Fax: +49-89-741518-19