[U-Boot-Users] MPC8245 custom board, Linux kernel hangs after uncompressing
Hi
I am trying to run Embedded linux (ELDK) on a custom powerpc board, which is similar to Artis A3000 board. This board has mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320 flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled U-boot for A3000 borad. U-boot worked on my board also. Next I compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But linux hangs after uncompressing
U-Boot 1.1.2 (Apr 14 2005 - 00:02:29)
CPU: MPC8245 Revision 1.2 at 249.999 MHz: 16 kB I-Cache 16 kB D-Cache Board: A3000 Local Bus at 99.999 MHz I2C: ready DRAM: 16 MB FLASH: Get flash bank 0 @ 0xffc00000 Manuf. ID @ 0xff800000: 0x00000089 Device ID @ 0xff800001: 0x00000016 ## Flash bank 0 at 0xffc00000 sizes: 0x00400000 protect monitor fff00000 @ 40000 protect environtment fffc0000 @ 20000 ## Final Flash bank sizes: 00400000 4 MB 00 13 100b 0020 0200 ff In: serial Out: serial Err: serial Net: natsemi: EEPROM contents: ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff dp83815#0 Warning: dp83815#0 MAC addresses don't match: Address in SROM is FF:FF:FF:FF:FF:FF Address in environment is 00:40:05:B0:F1:BA
A3000> tftpboot 400000 uImage.eldk Using dp83815#0 device TFTP from server 192.168.1.124; our IP address is 192.168.1.54 Filename 'uImage.eldk'. Load address: 0x400000 Loading: ################################################################# ################################################################# ################### done Bytes transferred = 757926 (b90a6 hex) A3000> bootm ## Booting image at 00400000 ... Image Name: Linux-2.4.25 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 757862 Bytes = 740.1 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK
nothing happens after this until I reboot the board. I read u-boot FAQ and configured bd_info structure same for both u-boot and Linux. I found that CFG_IMMR is not applicable to MPC8245. I also used clocks_in_mhz variable also before loading Linux. I am stuck here. Could you please let me know what should I do next?
Thanks Kishore
In message 2cf2641f0504191646536d2ad5@mail.gmail.com you wrote:
I am trying to run Embedded linux (ELDK) on a custom powerpc board, which is similar to Artis A3000 board. This board has mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320 flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled U-boot for A3000 borad. U-boot worked on my board also. Next I compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But
I don't think that you compiled the _ELDK_!
linux hangs after uncompressing
...
nothing happens after this until I reboot the board. I read u-boot FAQ and configured bd_info structure same for both u-boot and Linux. I found that CFG_IMMR is not applicable to MPC8245. I also used clocks_in_mhz variable also before loading Linux. I am stuck here.
I hope with "used" you mean that you made sure it is NOT set.
Could you please let me know what should I do next?
You make a fundamental error. You're using an U-Boot configuration which has not been correctly ported and configured to your board, and you're using a Linux kernel which has not been correctly ported and configured to your board.
This cannot work. Go back to square 1.
Best regards,
Wolfgang Denk
Hi
Thanks for your reply. U-boot is working very well on the custom mpc8245 board. I did some changes in the A3000.h file to make it work. All most all the features of u-boot are working. Problem comes when I load linux on to it. I compiled ELDK 3.0 verison. Since ELDK 3.0 does not have A3000 configuration I modified Sandpoint8245 configuration and compiled it. As I mentioned I did all the 3 steps mentioned in FAQ for "linux hangs after uncompressing" problem.
1. I configured linux kernel Sandpoint8245 .config file with flash and network drivers needed for my board. Is there any thing I need to do for SDRAM? 2. When I tried to run vmlinux using BDI2000 (with out u-boot) I got the following output
BDI>prog 0xffc00000 vmlinux.eldk bin Programming vmlinux.eldk , please wait .... Programming flash passed BDI>go 0xffc00000 - TARGET: target has entered debug mode BDI>info Target CPU : MPC82xx (G2H4) Target state : debug mode Debug entry cause : FPU unavailable exception Current PC : 0x00000000 Current CR : 0x20000000 Current MSR : 0x00000000 Current LR : 0xffd7ee18
Is there any thing I need to do to fix this.
3. Is there any embedded linux available for the artis A3000 type of board?
Thanks Kishore
On 4/19/05, Wolfgang Denk wd@denx.de wrote:
In message 2cf2641f0504191646536d2ad5@mail.gmail.com you wrote:
I am trying to run Embedded linux (ELDK) on a custom powerpc board, which is similar to Artis A3000 board. This board has mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320 flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled U-boot for A3000 borad. U-boot worked on my board also. Next I compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But
I don't think that you compiled the _ELDK_!
linux hangs after uncompressing
...
nothing happens after this until I reboot the board. I read u-boot FAQ and configured bd_info structure same for both u-boot and Linux. I found that CFG_IMMR is not applicable to MPC8245. I also used clocks_in_mhz variable also before loading Linux. I am stuck here.
I hope with "used" you mean that you made sure it is NOT set.
Could you please let me know what should I do next?
You make a fundamental error. You're using an U-Boot configuration which has not been correctly ported and configured to your board, and you're using a Linux kernel which has not been correctly ported and configured to your board.
This cannot work. Go back to square 1.
Best regards,
Wolfgang Denk
-- Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de If A equals success, then the formula is A = X + Y + Z. X is work. Y is play. Z is keep your mouth shut. - Albert Einstein
On 4/21/05, Kishore Devireddy kishorekrd@gmail.com wrote:
- Is there any embedded linux available for the artis A3000 type of board?
You're keep referring to A3000, I'm just wondering why. A3000 is a reference board from Artis Micro. Its referencing MPC8245. But artis have stopped rolling out this model for something like 2 years now. And trying to find linux ported for this model would be quite hard.
Alternative is to use Sandpoint8245.
After using A3000 myself, it worked well with the custom image (ppcboot 1.1.6) but putting on no customized version of u-boot (latest), it failed short in many aspect. So, my guess is that, even if your board is one off A3000, you still have to do some hard work to port for your board.
Alternatively, you could try getting answers from GDA Technologies (www.gdatech.com). They did the porting for A3000 model. I tried getting answers from Artis Micro Systems, and got no helpful answer but "we have stopped supporting this model" reply. :P
participants (3)
-
Daniel Ann -
Kishore Devireddy -
Wolfgang Denk